Softwire Working Group Y. Cui Internet-Draft Tsinghua University Intended status: Standards Track Q. Sun Expires: April 17, 2015 China Telecom M. Boucadair France Telecom T. Tsou Huawei Technologies Y. Lee Comcast I. Farrer Deutsche Telekom AG October 14, 2014 Lightweight 4over6: An Extension to the DS-Lite Architecture draft-ietf-softwire-lw4over6-11 Abstract Dual-Stack Lite (RFC 6333) describes an architecture for transporting IPv4 packets over an IPv6 network. This document specifies an extension to DS-Lite called Lightweight 4over6 which moves the Network Address and Port Translation (NAPT) function from the centralized DS-Lite tunnel concentrator to the tunnel client located in the Customer Premises Equipment (CPE). This removes the requirement for a Carrier Grade NAT function in the tunnel concentrator and reduces the amount of centralized state that must be held to a per-subscriber level. In order to delegate the NAPT function and make IPv4 Address sharing possible, port-restricted IPv4 addresses are allocated to the CPEs. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on April 17, 2015. Cui, et al. Expires April 17, 2015 [Page 1] Internet-Draft Lightweight 4over6 October 2014 Copyright Notice Copyright (c) 2014 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Conventions . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4 4. Lightweight 4over6 Architecture . . . . . . . . . . . . . . . 5 5. Lightweight B4 Behavior . . . . . . . . . . . . . . . . . . . 7 5.1. Lightweight B4 Provisioning with DHCPv6 . . . . . . . . . 7 5.2. Lightweight B4 Data Plane Behavior . . . . . . . . . . . 9 5.2.1. Changes to RFC2473 and RFC6333 Fragmentation Behaviour . . . . . . . . . . . . . . . . . . . . . . 10 6. Lightweight AFTR Behavior . . . . . . . . . . . . . . . . . . 11 6.1. Binding Table Maintenance . . . . . . . . . . . . . . . . 11 6.2. lwAFTR Data Plane Behavior . . . . . . . . . . . . . . . 11 7. Additional IPv4 address and Port Set Provisioning Mechanisms . . . . . . . . . . . . . . . . . . . . . . . . . 12 8. ICMP Processing . . . . . . . . . . . . . . . . . . . . . . . 13 8.1. ICMPv4 Processing by the lwAFTR . . . . . . . . . . . . . 13 8.2. ICMPv4 Processing by the lwB4 . . . . . . . . . . . . . . 14 9. Security Considerations . . . . . . . . . . . . . . . . . . . 14 10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 14 11. Author List . . . . . . . . . . . . . . . . . . . . . . . . . 14 12. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 18 13. References . . . . . . . . . . . . . . . . . . . . . . . . . 18 13.1. Normative References . . . . . . . . . . . . . . . . . . 18 13.2. Informative References . . . . . . . . . . . . . . . . . 19 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 20 1. Introduction Dual-Stack Lite (DS-Lite, [RFC6333]) defines a model for providing IPv4 access over an IPv6 network using two well-known technologies: Cui, et al. Expires April 17, 2015 [Page 2] Internet-Draft Lightweight 4over6 October 2014 IP in IP [RFC2473] and Network Address Translation (NAT). The DS- Lite architecture defines two major functional elements as follows: Basic Bridging BroadBand element: A B4 element is a function implemented on a dual-stack capable node, either a directly connected device or a CPE, that creates a tunnel to an AFTR. Address Family Transition Router: An AFTR element is the combination of an IPv4-in-IPv6 tunnel endpoint and an IPv4-IPv4 NAT implemented on the same node. As the AFTR performs the centralized NAT44 function, it dynamically assigns public IPv4 addresses and ports to requesting host's traffic (as described in [RFC3022]). To achieve this, the AFTR must dynamically maintain per-flow state in the form of active NAPT sessions. For service providers with a large number of B4 clients, the size and associated costs for scaling the AFTR can quickly become prohibitive. It can also place a large NAPT logging overhead upon the service provider in countries where legal requirements mandate this. This document describes a mechanism called Lightweight 4 over 6 (lw4o6), which provides a solution for these problems. By relocating the NAPT functionality from the centralized AFTR to the distributed B4s, a number of benefits can be realised: o NAPT44 functionality is already widely supported and used in today's CPE devices. Lw4o6 uses this to provide private<->public NAPT44, meaning that the service provider does not need a centralized NAT44 function. o The amount of state that must be maintained centrally in the AFTR can be reduced from per-flow to per-subscriber. This reduces the amount of resources (memory and processing power) necessary in the AFTR. o The reduction of maintained state results in a greatly reduced logging overhead on the service provider. Operator's IPv6 and IPv4 addressing architectures remain independent of each other. Therefore, flexible IPv4/IPv6 addressing schemes can be deployed. Lightweight 4over6 is a solution designed specifically for complete independence between IPv6 subnet prefix and IPv4 address with or Cui, et al. Expires April 17, 2015 [Page 3] Internet-Draft Lightweight 4over6 October 2014 without IPv4 address sharing. This is accomplished by maintaining state for each softwire (per-subscriber state) in the central lwAFTR and a hub-and-spoke forwarding architecture. [I-D.ietf-softwire-map] also offers these capabilities or, alternatively, allows for a reduction of the amount of centralized state using rules to express IPv4/IPv6 address mappings. This introduces an algorithmic relationship between the IPv6 subnet and IPv4 address. This relationship also allows the option of direct, meshed connectivity between users. The tunneling mechanism remains the same for DS-Lite and Lightweight 4over6. This document describes the changes to DS-Lite that are necessary to implement Lightweight 4over6. These changes mainly concern the configuration parameters and provisioning method necessary for the functional elements. Lightweight 4over6 features keeping per-subscriber state in the service provider's network. It is categorized as Binding approach in [I-D.ietf-softwire-unified-cpe] which defines a unified IPv4-in-IPv6 Softwire CPE. This document is an extended case, which covers address sharing for [RFC7040]. It is also a variant of A+P called Binding Table Mode (see Section 4.4 of [RFC6346]). This document focuses on architectural considerations and particularly on the expected behavior of the involved functional elements and their interfaces. Deployment-specific issues are discussed in a companion document. As such, discussions about redundancy and provisioning policy are out of scope. 2. Conventions The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. 3. Terminology The document defines the following terms: Lightweight 4over6 (lw4o6): An IPv4-over-IPv6 hub and spoke mechanism, which extends DS-Lite by moving the IPv4 translation (NAPT44) function from the AFTR to the B4. Lightweight B4 (lwB4): A B4 element (Basic Bridging BroadBand element [RFC6333]), which supports Cui, et al. Expires April 17, 2015 [Page 4] Internet-Draft Lightweight 4over6 October 2014 Lightweight 4over6 extensions. An lwB4 is a function implemented on a dual- stack capable node, (either a directly connected device or a CPE), that supports port-restricted IPv4 address allocation, implements NAPT44 functionality and creates a tunnel to an lwAFTR. Lightweight AFTR (lwAFTR): An AFTR element (Address Family Transition Router element [RFC6333]), which supports Lightweight 4over6 extension. An lwAFTR is an IPv4-in- IPv6 tunnel endpoint which maintains per-subscriber address binding only and does not perform a NAPT44 function. Restricted Port-Set: A non-overlapping range of allowed external ports allocated to the lwB4 to use for NAPT44. Source ports of IPv4 packets sent by the B4 must belong to the assigned port-set. The port set is used for all port aware IP protocols (TCP, UDP, SCTP etc.). Port-restricted IPv4 Address: A public IPv4 address with a restricted port-set. In Lightweight 4over6, multiple B4s may share the same IPv4 address, however, their port-sets must be non-overlapping. Throughout the remainder of this document, the terms B4/AFTR should be understood to refer specifically to a DS-Lite implementation. The terms lwB4/lwAFTR refer to a Lightweight 4over6 implementation. 4. Lightweight 4over6 Architecture The Lightweight 4over6 architecture is functionally similar to DS- Lite. lwB4s and an lwAFTR are connected through an IPv6-enabled network. Both approaches use an IPv4-in-IPv6 encapsulation scheme to deliver IPv4 connectivity. The following figure shows the data plane with the main functional change between DS-Lite and lw4o6: Cui, et al. Expires April 17, 2015 [Page 5] Internet-Draft Lightweight 4over6 October 2014 +--------+ +---------+ IPv4-in-IPv6 +---------+ +-------------+ |IPv4 LAN|---| B4 |==================|AFTR/NAPT|----|IPv4Internet| +--------+ +---------+ +---------+ +-------------+ DS-Lite NAPT model: all state in the AFTR +--------+ +---------+ IPv4-in-IPv6 +------+ +-------------+ |IPv4 LAN|---|lwB4/NAPT|==================|lwAFTR|----|IPv4 Internet| +--------+ +---------+ +------+ +-------------+ LW4over6 NAPT model: subscriber state in the lwAFTR, NAPT state in lwB4 Figure 1 Comparison of DS-Lite and Lightweight 4over6 Data Plane There are three main components in the Lightweight 4over6 architecture: o The lwB4, which performs the NAPT function and encapsulation/de- capsulation IPv4/IPv6. o The lwAFTR, which performs the encapsulation/de-capsulation IPv4/ IPv6. o The provisioning system, which tells the lwB4 which IPv4 address and port set to use. The lwB4 differs from a regular B4 in that it now performs the NAPT functionality. This means that it needs to be provisioned with the public IPv4 address and port set it is allowed to use. This information is provided though a provisioning mechanism such as DHCP, PCP or TR-69. The lwAFTR needs to know the binding between the IPv6 address of each subscriber and the IPv4 address and port set allocated to that subscriber. This information is used to perform ingress filtering upstream and encapsulation downstream. Note that this is per- subscriber state as opposed to per-flow state in the regular AFTR case. The consequence of this architecture is that the information maintained by the provisioning mechanism and the one maintained by the lwAFTR MUST be synchronized (See figure 2). The details of this synchronization depend on the exact provisioning mechanism and will be discussed in a companion document. The solution specified in this document allows the assignment of either a full or a shared IPv4 address requesting CPEs. [RFC7040] provides a mechanism for assigning a full IPv4 address only. Cui, et al. Expires April 17, 2015 [Page 6] Internet-Draft Lightweight 4over6 October 2014 +------------+ /-------|Provisioning|<-----\ | +------------+ | | | V V +--------+ +---------+ IPv4/IPv6 +------+ +-------------+ |IPv4 LAN|---|lwB4/NAPT|==================|lwAFTR|----|IPv4 Internet| +--------+ +---------+ +------+ +-------------+ Figure 2 Lightweight 4over6 Provisioning Synchronization 5. Lightweight B4 Behavior 5.1. Lightweight B4 Provisioning with DHCPv6 With DS-Lite, the B4 element only needs to be configured with a single DS-Lite specific parameter so that it can set up the softwire (the IPv6 address of the AFTR). Its IPv4 address can be taken from the well-known range 192.0.0.0/29. In lw4o6, a number of lw4o6 specific configuration parameters must be provisioned to the lwB4. These are: o IPv6 Address for the lwAFTR o IPv4 External (Public) Address for NAPT44 o Restricted port-set to use for NAPT44 o IPv6 Binding Prefix For DHCPv6 based configuration of these parameters, the lwB4 SHOULD implement OPTION_S46_CONT_LW as described in section 5.3 of [I-D.ietf-softwire-map-dhcp]. This means that the lifetime of the softwire and the derived configuration information (e.g. IPv4 shared address, IPv4 address) is bound to the lifetime of the DHCPv6 lease. If stateful IPv4 configuration or additional IPv4 configuration information is required, DHCP 4o6 [RFC7341] must be used. Although it would be possible to extend lw4o6 to have more than one active lw4o6 tunnel configured simultaneously, this document is only concerned with the use of a single tunnel. The IPv6 binding prefix field is provisioned so that the CE can identify the correct prefix to use as the tunnel source. On receipt of the necessary configuration parameters listed in Section 5.1 of this document, the lwB4 performs a longest prefix match between the IPv6 binding prefix and its currently active IPv6 prefixes. The Cui, et al. Expires April 17, 2015 [Page 7] Internet-Draft Lightweight 4over6 October 2014 result forms the subnet to be used for sourcing the lw4o6 tunnel. The full /128 address is then constructed in the same manner as [I-D.ietf-softwire-map]. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Operator Assigned Prefix | . (64-bits) . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Zero Padding | IPv4 Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IPv4 Addr cont. | PSID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 3 Construction of the lw4o6 /128 Prefix Operator Assigned Prefix: IPv6 prefix allocated to the client. If the prefix length is less than 64, right padded with zeros to 64-bits. Padding: Padding (all zeros) IPv4 Address: Public IPv4 address allocated to the client PSID: Port Set ID allocated to the client, left padded with zeros to 16-bits. If no PSID is provisioned, all zeros. In the event that the lwB4's IPv6 encapsulation source address is changed for any reason (such as the DHCPv6 lease expiring), the lwB4's dynamic provisioning process must be re-initiated. When the lwB4's public IPv4 address or port set ID is changed for any reason, the lwB4 must flush its NAPT table. An lwB4 MUST support dynamic port-restricted IPv4 address provisioning. The port set algorithm for provisioning this is described in Section 5.1 of [I-D.ietf-softwire-map]. For lw4o6, the number of a-bits SHOULD be 0, thus allocating a single contiguous port set to each lwB4. Unless an lwB4 is being allocated a full IPv4 address, it is RECOMMENDED that PSIDs containing the well-known ports (0-1023) are not allocated to lwB4s. Cui, et al. Expires April 17, 2015 [Page 8] Internet-Draft Lightweight 4over6 October 2014 In the event that the lwB4 receives an ICMPv6 error message (type 1, code 5) originating from the lwAFTR, the lwB4 SHOULD interpret this to mean that no matching entry in the lwAFTR's binding table has been found. The lwB4 MAY then re-initiate the dynamic port-restricted provisioning process. The lwB4's re-initiation policy SHOULD be configurable. The DNS considerations described in Section 5.5 and Section 6.4 of [RFC6333] SHOULD be followed. 5.2. Lightweight B4 Data Plane Behavior Several sections of [RFC6333] provide background information on the B4's data plane functionality and MUST be implemented by the lwB4 as they are common to both solutions. The relevant sections are: 5.2 Encapsulation Covering encapsulation and de- capsulation of tunneled traffic 5.3 Fragmentation and Reassembly Covering MTU and fragmentation considerations (referencing [RFC2473]), with the exception noted below. 7.1 Tunneling Covering tunneling and traffic class mapping between IPv4 and IPv6 (referencing [RFC2473] and [RFC2983]) The lwB4 element performs IPv4 address translation (NAPT44) as well as encapsulation and de-capsulation. It runs standard NAPT44 [RFC3022] using the allocated port-restricted address as its external IPv4 address and port numbers. The working flow of the lwB4 is illustrated in figure 4. +-------------+ | lwB4 | +--------+ IPv4 |------+------| IPv4-in-IPv6 +----------+ |IPv4 LAN|------->| |Encap.|-------------->|Configured| | |<-------| NAPT | or |<--------------| lwAFTR | +--------+ | |Decap.| +----------+ +------+------+ Figure 4 Working Flow of the lwB4 Internally connected hosts source IPv4 packets with an [RFC1918] address. When the lwB4 receives such an IPv4 packet, it performs a Cui, et al. Expires April 17, 2015 [Page 9] Internet-Draft Lightweight 4over6 October 2014 NAPT44 function on the source address and port by using the public IPv4 address and a port number from the allocated port-set. Then, it encapsulates the packet with an IPv6 header. The destination IPv6 address is the lwAFTR's IPv6 address and the source IPv6 address is the lwB4's IPv6 tunnel endpoint address. Finally, the lwB4 forwards the encapsulated packet to the configured lwAFTR. When the lwB4 receives an IPv4-in-IPv6 packet from the lwAFTR, it de- capsulates the IPv4 packet from the IPv6 packet. Then, it performs NAPT44 translation on the destination address and port, based on the available information in its local NAPT44 table. If the IPv6 source address does not match the configured lwAFTR address, then the packet MUST be discarded. If the decapsulated IPv4 packet does not match the lwB4's configuration (i.e. invalid destination IPv4 address or port) then the packet MUST be dropped. An ICMPv4 error message (type 13 - Communication Administratively Prohibited) message MAY be sent back to the lwAFTR. The ICMP policy SHOULD be configurable. The lwB4 is responsible for performing ALG functions (e.g., SIP, FTP), and other NAPT traversal mechanisms (e.g., UPnP, NAPT-PMP, manual binding configuration, PCP) for the internal hosts. This requirement is typical for NAPT44 gateways available today. It is possible that a lwB4 is co-located in a host. In this case, the functions of NAPT44 and encapsulation/de-capsulation are implemented inside the host. 5.2.1. Changes to RFC2473 and RFC6333 Fragmentation Behaviour For TCP and UDP traffic the NAPT44 implemented in the lwB4 SHOULD conform with the behaviour and best current practices documented in [RFC4787], [RFC5508], and [RFC5382]. If the lwB4 supports DCCP, then the requirements in [RFC5597] SHOULD be implemented. The NAPT44 in the lwB4 MUST implement ICMP message handling behaviour conforming to the best current practice documented in [RFC5508]. If the lwB4 receives an ICMP error (for errors detected inside the IPv6 tunnel), the node should relay the ICMP error message to the original source (the lwAFTR). This behaviour SHOULD be implemented conforming to the section 8 of [RFC2473]. Cui, et al. Expires April 17, 2015 [Page 10] Internet-Draft Lightweight 4over6 October 2014 6. Lightweight AFTR Behavior 6.1. Binding Table Maintenance The lwAFTR maintains an address binding table containing the binding between the lwB4's IPv6 address, the allocated IPv4 address and restricted port-set. Unlike the DS-Lite extended binding table defined in section 6.6 of [RFC6333] which is a 5-tuple NAPT table, each entry in the Lightweight 4over6 binding table contains the following 3-tuples: o IPv6 Address for a single lwB4 o Public IPv4 Address o Restricted port-set The entry has two functions: the IPv6 encapsulation of inbound IPv4 packets destined to the lwB4 and the validation of outbound IPv4-in- IPv6 packets received from the lwB4 for de-capsulation. The lwAFTR does not perform NAPT and so does not need session entries. The lwAFTR MUST synchronize the binding information with the port- restricted address provisioning process. If the lwAFTR does not participate in the port-restricted address provisioning process, the binding MUST be synchronized through other methods (e.g. out-of-band static update). If the lwAFTR participates in the port-restricted provisioning process, then its binding table MUST be created as part of this process. For all provisioning processes, the lifetime of binding table entries MUST be synchronized with the lifetime of address allocations. 6.2. lwAFTR Data Plane Behavior Several sections of [RFC6333] provide background information on the AFTR's data plane functionality and MUST be implemented by the lwAFTR as they are common to both solutions. The relevant sections are: 6.2 Encapsulation Covering encapsulation and de- capsulation of tunneled traffic Cui, et al. Expires April 17, 2015 [Page 11] Internet-Draft Lightweight 4over6 October 2014 6.3 Fragmentation and Reassembly Fragmentation and re-assembly considerations (referencing [RFC2473]) 7.1 Tunneling Covering tunneling and traffic class mapping between IPv4 and IPv6 (referencing [RFC2473] and [RFC2983]) When the lwAFTR receives an IPv4-in-IPv6 packet from an lwB4, it de- capsulates the IPv6 header and verifies the source addresses and port in the binding table. If both the source IPv4 and IPv6 addresses match a single entry in the binding table and the source port is in the allowed port-set for that entry, the lwAFTR forwards the packet to the IPv4 destination. If no match is found (e.g., no matching IPv4 address entry, port out of range, etc.), the lwAFTR MUST discard or implement a policy (such as redirection) on the packet. An ICMPv6 type 1, code 5 (source address failed ingress/egress policy) error message MAY be sent back to the requesting lwB4. The ICMP policy SHOULD be configurable. When the lwAFTR receives an inbound IPv4 packet, it uses the IPv4 destination address and port to lookup the destination lwB4's IPv6 address in its binding table. If a match is found, the lwAFTR encapsulates the IPv4 packet. The source is the lwAFTR's IPv6 address and the destination is the lwB4's IPv6 address from the matched entry. Then, the lwAFTR forwards the packet to the lwB4 natively over the IPv6 network. If no match is found, the lwAFTR MUST discard the packet. An ICMPv4 type 3, code 1 (Destination unreachable, host unreachable) error message MAY be sent back. The ICMP policy SHOULD be configurable. The lwAFTR MUST support hairpinning of traffic between two lwB4s, by performing de-capsulation and re-encapsulation of packets. The hairpinning policy MUST be configurable. 7. Additional IPv4 address and Port Set Provisioning Mechanisms In addition to the DHCPv6 based mechanism described in section 5.1, several other IPv4 provisioning protocols have been suggested. These protocols MAY be implemented. These alternatives include: o DHCPv4 over DHCPv6: [RFC7341] describes implementing DHCPv4 messages over an IPv6 only service providers network. This enables leasing of IPv4 addresses and makes DHCPv4 options available to the DHCPv4 over DHCPv6 client. Cui, et al. Expires April 17, 2015 [Page 12] Internet-Draft Lightweight 4over6 October 2014 o PCP[RFC6887]: an lwB4 MAY use [I-D.ietf-pcp-port-set] to retrieve a restricted IPv4 address and a set of ports. In a Lightweight 4over6 domain, the binding information MUST be aligned between the lwB4s, the lwAFTRs and the provisioning server. 8. ICMP Processing For both the lwAFTR and the lwB4, ICMPv6 MUST be handled as described in [RFC2473]. ICMPv4 does not work in an address sharing environment without special handling [RFC6269]. Due to the port-set style address sharing, Lightweight 4over6 requires specific ICMP message handling not required by DS-Lite. 8.1. ICMPv4 Processing by the lwAFTR For inbound ICMP messages The following behavior SHOULD be implemented by the lwAFTR to provide ICMP error handling and basic remote IPv4 service diagnostics for a port restricted CPE: 1. Check the ICMP Type field. 2. If the ICMP type is set to 0 or 8 (echo reply or request), then the lwAFTR MUST take the value of the ICMP identifier field as the source port, and use this value to lookup the binding table for an encapsulation destination. If a match is found, the lwAFTR forwards the ICMP packet to the IPv6 address stored in the entry; otherwise it MUST discard the packet. 3. If the ICMP type field is set to any other value, then the lwAFTR MUST use the method described in REQ-3 of [RFC5508] to locate the source port within the transport layer header in ICMP packet's data field. The destination IPv4 address and source port extracted from the ICMP packet are then used to make a lookup in the binding table. If a match is found, it MUST forward the ICMP reply packet to the IPv6 address stored in the entry; otherwise it MUST discard the packet. Additionally, the lwAFTR MAY implement: o Discarding of all inbound ICMP messages. The ICMP policy SHOULD be configurable. Cui, et al. Expires April 17, 2015 [Page 13] Internet-Draft Lightweight 4over6 October 2014 8.2. ICMPv4 Processing by the lwB4 The lwB4 SHOULD implement the requirements defined in [RFC5508] for ICMP forwarding. For ICMP echo request packets originating from the private IPv4 network, the lwB4 SHOULD implement the method described in [RFC6346] and use an available port from its port-set as the ICMP Identifier. 9. Security Considerations As the port space for a subscriber shrinks due to address sharing, the randomness for the port numbers of the subscriber is decreased significantly. This means it is much easier for an attacker to guess the port number used, which could result in attacks ranging from throughput reduction to broken connections or data corruption. The port-set for a subscriber can be a set of contiguous ports or non-contiguous ports. Contiguous port-sets do not reduce this threat. However, with non-contiguous port-set (which may be generated in a pseudo-random way [RFC6431]), the randomness of the port number is improved, provided that the attacker is outside the Lightweight 4over6 domain and hence does not know the port-set generation algorithm. More considerations about IP address sharing are discussed in Section 13 of [RFC6269], which is applicable to this solution. 10. IANA Considerations This document does not include an IANA request. 11. Author List The following are extended authors who contributed to the effort: Jianping Wu Tsinghua University Department of Computer Science, Tsinghua University Beijing 100084 P.R.China Phone: +86-10-62785983 Email: jianping@cernet.edu.cn Cui, et al. Expires April 17, 2015 [Page 14] Internet-Draft Lightweight 4over6 October 2014 Peng Wu Tsinghua University Department of Computer Science, Tsinghua University Beijing 100084 P.R.China Phone: +86-10-62785822 Email: pengwu.thu@gmail.com Qi Sun Tsinghua University Beijing 100084 P.R.China Phone: +86-10-62785822 Email: sunqi@csnet1.cs.tsinghua.edu.cn Chongfeng Xie China Telecom Room 708, No.118, Xizhimennei Street Beijing 100035 P.R.China Phone: +86-10-58552116 Email: xiechf@ctbri.com.cn Xiaohong Deng Cui, et al. Expires April 17, 2015 [Page 15] Internet-Draft Lightweight 4over6 October 2014 France Telecom Email: xiaohong.deng@orange.com Cathy Zhou Huawei Technologies Section B, Huawei Industrial Base, Bantian Longgang Shenzhen 518129 P.R.China Email: cathyzhou@huawei.com Alain Durand Juniper Networks 1194 North Mathilda Avenue Sunnyvale, CA 94089-1206 USA Email: adurand@juniper.net Reinaldo Penno Cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134 USA Email: repenno@cisco.com Cui, et al. Expires April 17, 2015 [Page 16] Internet-Draft Lightweight 4over6 October 2014 Axel Clauberg Deutsche Telekom AG CTO-ATI Landgrabenweg 151 Bonn, 53227 Germany Email: axel.clauberg@telekom.de Lionel Hoffmann Bouygues Telecom TECHNOPOLE 13/15 Avenue du Marechal Juin Meudon 92360 France Email: lhoffman@bouyguestelecom.fr Maoke Chen FreeBit Co., Ltd. 13F E-space Tower, Maruyama-cho 3-6 Shibuya-ku, Tokyo 150-0044 Japan Email: fibrib@gmail.com Cui, et al. Expires April 17, 2015 [Page 17] Internet-Draft Lightweight 4over6 October 2014 12. Acknowledgement The authors would like to thank Ole Troan, Ralph Droms and Suresh Krishnan for their comments and feedback. This document is a merge of three documents: [I-D.cui-softwire-b4-translated-ds-lite], [I-D.zhou-softwire-b4-nat] and [I-D.penno-softwire-sdnat]. 13. References 13.1. Normative References [I-D.ietf-softwire-map-dhcp] Mrugalski, T., Troan, O., Farrer, I., Perreault, S., Dec, W., Bao, C., leaf.yeh.sdo@gmail.com, l., and X. Deng, "DHCPv6 Options for configuration of Softwire Address and Port Mapped Clients", draft-ietf-softwire-map-dhcp-09 (work in progress), October 2014. [RFC1918] Rekhter, Y., Moskowitz, R., Karrenberg, D., Groot, G., and E. Lear, "Address Allocation for Private Internets", BCP 5, RFC 1918, February 1996. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2473] Conta, A. and S. Deering, "Generic Packet Tunneling in IPv6 Specification", RFC 2473, December 1998. [RFC4787] Audet, F. and C. Jennings, "Network Address Translation (NAT) Behavioral Requirements for Unicast UDP", BCP 127, RFC 4787, January 2007. [RFC5382] Guha, S., Biswas, K., Ford, B., Sivakumar, S., and P. Srisuresh, "NAT Behavioral Requirements for TCP", BCP 142, RFC 5382, October 2008. [RFC5508] Srisuresh, P., Ford, B., Sivakumar, S., and S. Guha, "NAT Behavioral Requirements for ICMP", BCP 148, RFC 5508, April 2009. [RFC5597] Denis-Courmont, R., "Network Address Translation (NAT) Behavioral Requirements for the Datagram Congestion Control Protocol", BCP 150, RFC 5597, September 2009. Cui, et al. Expires April 17, 2015 [Page 18] Internet-Draft Lightweight 4over6 October 2014 [RFC6333] Durand, A., Droms, R., Woodyatt, J., and Y. Lee, "Dual- Stack Lite Broadband Deployments Following IPv4 Exhaustion", RFC 6333, August 2011. 13.2. Informative References [I-D.cui-softwire-b4-translated-ds-lite] Cui, Y., Sun, Q., Boucadair, M., Tsou, T., Lee, Y., and I. Farrer, "Lightweight 4over6: An Extension to the DS-Lite Architecture", draft-cui-softwire-b4-translated-ds-lite-11 (work in progress), February 2013. [I-D.ietf-pcp-port-set] Qiong, Q., Boucadair, M., Sivakumar, S., Zhou, C., Tsou, T., and S. Perreault, "Port Control Protocol (PCP) Extension for Port Set Allocation", draft-ietf-pcp-port- set-06 (work in progress), July 2014. [I-D.ietf-softwire-map] Troan, O., Dec, W., Li, X., Bao, C., Matsushima, S., Murakami, T., and T. Taylor, "Mapping of Address and Port with Encapsulation (MAP)", draft-ietf-softwire-map-11 (work in progress), October 2014. [I-D.ietf-softwire-unified-cpe] Boucadair, M., Farrer, I., Perreault, S., and S. Sivakumar, "Unified IPv4-in-IPv6 Softwire CPE", draft- ietf-softwire-unified-cpe-01 (work in progress), May 2013. [I-D.penno-softwire-sdnat] Penno, R., Durand, A., Hoffmann, L., and A. Clauberg, "Stateless DS-Lite", draft-penno-softwire-sdnat-02 (work in progress), March 2012. [I-D.zhou-softwire-b4-nat] Zhou, C., Boucadair, M., and X. Deng, "NAT offload extension to Dual-Stack lite", draft-zhou-softwire- b4-nat-04 (work in progress), October 2011. [RFC2983] Black, D., "Differentiated Services and Tunnels", RFC 2983, October 2000. [RFC3022] Srisuresh, P. and K. Egevang, "Traditional IP Network Address Translator (Traditional NAT)", RFC 3022, January 2001. Cui, et al. Expires April 17, 2015 [Page 19] Internet-Draft Lightweight 4over6 October 2014 [RFC6269] Ford, M., Boucadair, M., Durand, A., Levis, P., and P. Roberts, "Issues with IP Address Sharing", RFC 6269, June 2011. [RFC6346] Bush, R., "The Address plus Port (A+P) Approach to the IPv4 Address Shortage", RFC 6346, August 2011. [RFC6431] Boucadair, M., Levis, P., Bajko, G., Savolainen, T., and T. Tsou, "Huawei Port Range Configuration Options for PPP IP Control Protocol (IPCP)", RFC 6431, November 2011. [RFC6887] Wing, D., Cheshire, S., Boucadair, M., Penno, R., and P. Selkirk, "Port Control Protocol (PCP)", RFC 6887, April 2013. [RFC7040] Cui, Y., Wu, J., Wu, P., Vautrin, O., and Y. Lee, "Public IPv4-over-IPv6 Access Network", RFC 7040, November 2013. [RFC7341] Sun, Q., Cui, Y., Siodelski, M., Krishnan, S., and I. Farrer, "DHCPv4-over-DHCPv6 (DHCP 4o6) Transport", RFC 7341, August 2014. Authors' Addresses Yong Cui Tsinghua University Beijing 100084 P.R.China Phone: +86-10-62603059 Email: yong@csnet1.cs.tsinghua.edu.cn Qiong Sun China Telecom Room 708, No.118, Xizhimennei Street Beijing 100035 P.R.China Phone: +86-10-58552936 Email: sunqiong@ctbri.com.cn Cui, et al. Expires April 17, 2015 [Page 20] Internet-Draft Lightweight 4over6 October 2014 Mohamed Boucadair France Telecom Rennes 35000 France Email: mohamed.boucadair@orange.com Tina Tsou Huawei Technologies 2330 Central Expressway Santa Clara, CA 95050 USA Phone: +1-408-330-4424 Email: tena@huawei.com Yiu L. Lee Comcast One Comcast Center Philadelphia, PA 19103 USA Email: yiu_lee@cable.comcast.com Ian Farrer Deutsche Telekom AG CTO-ATI, Landgrabenweg 151 Bonn, NRW 53227 Germany Email: ian.farrer@telekom.de Cui, et al. Expires April 17, 2015 [Page 21]