Network Working Group O. Troan, Ed. Internet-Draft W. Dec Intended status: Standards Track Cisco Systems Expires: April 16, 2015 X. Li C. Bao CERNET Center/Tsinghua University S. Matsushima SoftBank Telecom T. Murakami IP Infusion T. Taylor, Ed. Huawei Technologies October 13, 2014 Mapping of Address and Port with Encapsulation (MAP) draft-ietf-softwire-map-11 Abstract This document describes a mechanism for transporting IPv4 packets across an IPv6 network using IP encapsulation, and a generic mechanism for mapping between IPv6 addresses and IPv4 addresses and transport layer ports. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on April 16, 2015. Copyright Notice Copyright (c) 2014 IETF Trust and the persons identified as the document authors. All rights reserved. Troan, et al. Expires April 16, 2015 [Page 1] Internet-Draft MAP October 2014 This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Conventions . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4 4. Architecture . . . . . . . . . . . . . . . . . . . . . . . . 5 5. Mapping Algorithm . . . . . . . . . . . . . . . . . . . . . . 7 5.1. Port mapping algorithm . . . . . . . . . . . . . . . . . 8 5.2. Basic mapping rule (BMR) . . . . . . . . . . . . . . . . 9 5.3. Forwarding mapping rule (FMR) . . . . . . . . . . . . . . 12 5.4. Destinations outside the MAP domain . . . . . . . . . . . 13 6. The IPv6 Interface Identifier . . . . . . . . . . . . . . . . 13 7. MAP Configuration . . . . . . . . . . . . . . . . . . . . . . 14 7.1. MAP CE . . . . . . . . . . . . . . . . . . . . . . . . . 14 7.2. MAP BR . . . . . . . . . . . . . . . . . . . . . . . . . 15 8. Forwarding Considerations . . . . . . . . . . . . . . . . . . 15 8.1. Receiving Rules . . . . . . . . . . . . . . . . . . . . . 15 8.2. ICMP . . . . . . . . . . . . . . . . . . . . . . . . . . 16 8.3. Fragmentation and Path MTU Discovery . . . . . . . . . . 17 8.3.1. Fragmentation in the MAP domain . . . . . . . . . . . 17 8.3.2. Receiving IPv4 Fragments on the MAP domain borders . 17 8.3.3. Sending IPv4 fragments to the outside . . . . . . . . 18 9. NAT44 Considerations . . . . . . . . . . . . . . . . . . . . 18 10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 18 11. Security Considerations . . . . . . . . . . . . . . . . . . . 18 12. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 19 13. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 20 14. References . . . . . . . . . . . . . . . . . . . . . . . . . 20 14.1. Normative References . . . . . . . . . . . . . . . . . . 20 14.2. Informative References . . . . . . . . . . . . . . . . . 20 Appendix A. Examples . . . . . . . . . . . . . . . . . . . . . . 23 Appendix B. A More Detailed Description of the Derivation of the Port Mapping Algorithm . . . . . . . . . . . . . . . 27 B.1. Bit Representation of the Algorithm . . . . . . . . . . . 29 B.2. GMA examples . . . . . . . . . . . . . . . . . . . . . . 30 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 30 Troan, et al. Expires April 16, 2015 [Page 2] Internet-Draft MAP October 2014 1. Introduction Mapping of IPv4 addresses in IPv6 addresses has been described in numerous mechanisms dating back to 1995 [RFC1933]. The Automatic tunneling mechanism described in RFC1933 assigned a globally unique IPv6 address to a host by combining the host's IPv4 address with a well-known IPv6 prefix. Given an IPv6 packet with a destination address with an embedded IPv4 address, a node could automatically tunnel this packet by extracting the IPv4 tunnel end-point address from the IPv6 destination address. There are numerous variations of this idea, described in 6over4 [RFC2529], 6to4 [RFC3056], ISATAP [RFC5214], and 6rd [RFC5969]. The commonalities of all these IPv6 over IPv4 mechanisms are: o Automatically provisions an IPv6 address for a host or an IPv6 prefix for a site o Algorithmic or implicit address resolution of tunnel end point addresses. Given an IPv6 destination address, an IPv4 tunnel endpoint address can be calculated. o Embedding of an IPv4 address or part thereof into an IPv6 address. In later phases of IPv4 to IPv6 migration, it is expected that IPv6-only networks will be common, while there will still be a need for residual IPv4 deployment. This document describes a generic mapping of IPv4 to IPv6, and a mechanism for encapsulating IPv4 over IPv6. Just as the IPv6 over IPv4 mechanisms referred to above, the residual IPv4 over IPv6 mechanism must be capable of: o Provisioning an IPv4 prefix, an IPv4 address or a shared IPv4 address. o Algorithmically map between either an IPv4 prefix, an IPv4 address or a shared IPv4 address and an IPv6 address. The mapping scheme described here supports encapsulation of IPv4 packets in IPv6 in both mesh and hub-and-spoke topologies, including address mappings with full independence between IPv6 and IPv4 addresses. This document describes delivery of IPv4 unicast service across an IPv6 infrastructure. IPv4 multicast is not considered further in this document. Troan, et al. Expires April 16, 2015 [Page 3] Internet-Draft MAP October 2014 The A+P (Address and Port) architecture of sharing an IPv4 address by distributing the port space is described in [RFC6346]. Specifically section 4 of [RFC6346] covers stateless mapping. The corresponding stateful solution DS-lite is described in [RFC6333]. The motivation for this work is described in [I-D.ietf-softwire-stateless-4v6-motivation]. A companion document defines a DHCPv6 option for provisioning of MAP [I-D.ietf-softwire-map-dhcp]. Other means of provisioning are possible. Deployment considerations are described in [I-D.ietf-softwire-map-deployment]. MAP relies on IPv6 and is designed to deliver dual-stack service while allowing IPv4 to be phased out within the service provider's (SP) network. The phasing out of IPv4 within the SP network is independent of whether the end user disables IPv4 service or not. Further, "greenfield"; IPv6-only networks may use MAP in order to deliver IPv4 to sites via the IPv6 network. 2. Conventions The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. 3. Terminology MAP domain: One or more MAP CEs and BRs connected to the same virtual link. A service provider may deploy a single MAP domain, or may utilize multiple MAP domains. MAP rule A set of parameters describing the mapping between an IPv4 prefix, IPv4 address or shared IPv4 address and an IPv6 prefix or address. Each domain uses a different mapping rule set. MAP node A device that implements MAP. MAP Border Relay (BR): A MAP enabled router managed by the service provider at the edge of a MAP domain. A Border Relay router has at least an IPv6-enabled interface and an IPv4 interface connected to the native IPv4 network. A MAP BR may also be referred to simply as a "BR" within the context of MAP. Troan, et al. Expires April 16, 2015 [Page 4] Internet-Draft MAP October 2014 MAP Customer Edge (CE): A device functioning as a Customer Edge router in a MAP deployment. A typical MAP CE adopting MAP rules will serve a residential site with one WAN side interface, and one or more LAN side interfaces. A MAP CE may also be referred to simply as a "CE" within the context of MAP. Port-set: The separate part of the transport layer port space; denoted as a port-set. Port-set ID (PSID): Algorithmically identifies a set of ports exclusively assigned to a CE. Shared IPv4 address: An IPv4 address that is shared among multiple CEs. Only ports that belong to the assigned port-set can be used for communication. Also known as a Port-Restricted IPv4 address. End-user IPv6 prefix: The IPv6 prefix assigned to an End-user CE by other means than MAP itself. E.g., Provisioned using DHCPv6 PD [RFC3633], assigned via SLAAC [RFC4862], or configured manually. It is unique for each CE. MAP IPv6 address: The IPv6 address used to reach the MAP function of a CE from other CEs and from BRs. Rule IPv6 prefix: An IPv6 prefix assigned by a Service Provider for a mapping rule. Rule IPv4 prefix: An IPv4 prefix assigned by a Service Provider for a mapping rule. Embedded Address (EA) bits: The IPv4 EA-bits in the IPv6 address identify an IPv4 prefix/address (or part thereof) or a shared IPv4 address (or part thereof) and a port-set identifier. 4. Architecture In accordance with the requirements stated above, the MAP mechanism can operate with shared IPv4 addresses, full IPv4 addresses or IPv4 prefixes. Operation with shared IPv4 addresses is described here, and the differences for full IPv4 addresses and prefixes are described below. Troan, et al. Expires April 16, 2015 [Page 5] Internet-Draft MAP October 2014 The MAP mechanism uses existing standard building blocks. The existing NAPT [RFC2663] on the CE is used with additional support for restricting transport protocol ports, ICMP identifiers and fragment identifiers to the configured port-set. For packets outbound from the private IPv4 network, the CE NAPT MUST translate transport identifiers (e.g., TCP and UDP port numbers) so that they fall within the CE's assigned port-range. The NAPT MUST in turn be connected to a MAP-aware forwarding function, that does encapsulation / decapsulation of IPv4 packets in IPv6. MAP supports the encapsulation mode specified in [RFC2473]. In addition MAP specifies an algorithm to do "address resolution" from an IPv4 address and port to an IPv6 address. This algorithmic mapping is specified in Section 5. The MAP architecture described here restricts the use of the shared IPv4 address to only be used as the global address (outside) of the NAPT running on the CE. A shared IPv4 address MUST NOT be used to identify an interface. While it is theoretically possible to make host stacks and applications port-aware, it would be a drastic change to the IP model [RFC6250]. For full IPv4 addresses and IPv4 prefixes, the architecture just described applies with two differences. First, a full IPv4 address or IPv4 prefix can be used as it is today, e.g., for identifying an interface or as a DHCP pool, respectively. Secondly, the NAPT is not required to restrict the ports used on outgoing packets. This architecture is illustrated in Figure 1. User N Private IPv4 | Network | O--+---------------O | | MAP CE | | +-----+--------+ | | NAPT44| MAP | | | +-----+ | |\ ,-------. .------. | +--------+ | \ ,-' `-. ,-' `-. O------------------O / \ O---------O / Public \ / IPv6 only \ | MAP | / IPv4 \ ( Network --+ Border +- Network ) \ (MAP Domain) / | Relay | \ / O------------------O \ / O---------O \ / | MAP CE | /". ,-' `-. ,-' | +-----+--------+ | / `----+--' ------' Troan, et al. Expires April 16, 2015 [Page 6] Internet-Draft MAP October 2014 | NAPT44| MAP | |/ | +-----+ | | | | +--------+ | O---+--------------O | User M Private IPv4 Network Figure 1: Network Topology The MAP BR connects one or more MAP domains to external IPv4 networks. 5. Mapping Algorithm A MAP node is provisioned with one or more mapping rules. Mapping rules are used differently depending on their function. Every MAP node must be provisioned with a Basic mapping rule. This is used by the node to configure its IPv4 address, IPv4 prefix or shared IPv4 address. This same basic rule can also be used for forwarding, where an IPv4 destination address and optionally a destination port are mapped into an IPv6 address. Additional mapping rules are specified to allow for multiple different IPv4 sub-nets to exist within the domain and optimize forwarding between them. Traffic outside of the domain (i.e., when the destination IPv4 address does not match (using longest matching prefix) any Rule IPv4 prefix in the Rules database) is forwarded to the BR. There are two types of mapping rules: 1. Basic Mapping Rule (BMR) - mandatory. A CE can be provisioned with multiple End-user IPv6 prefixes. There can only be one Basic Mapping Rule per End-user IPv6 prefix. However all CE's having End-user IPv6 prefixes within (aggregated by) the same Rule IPv6 prefix may share the same Basic Mapping Rule. In combination with the End-user IPv6 prefix, the Basic Mapping Rule is used to derive the IPv4 prefix, address, or shared address and the PSID assigned to the CE. 2. Forwarding Mapping Rule (FMR) - optional, used for forwarding. The Basic Mapping Rule may also be a Forwarding Mapping Rule. Each Forwarding Mapping Rule will result in an entry in the Rules table for the Rule IPv4 prefix. Given a destination IPv4 address and port within the MAP domain, a MAP node can use the matching Troan, et al. Expires April 16, 2015 [Page 7] Internet-Draft MAP October 2014 FMR to derive the End-user IPv6 address of the interface through which that IPv4 destination address and port combination can be reached. In hub and spoke mode there are no FMRs. Both mapping rules share the same parameters: o Rule IPv6 prefix (including prefix length) o Rule IPv4 prefix (including prefix length) o Rule EA-bits length (in bits) A MAP node finds its BMR by doing a longest match between the End- user IPv6 prefix and the Rule IPv6 prefix in the Mapping Rules table. The rule is then used for IPv4 prefix, address or shared address assignment. A MAP IPv6 address is formed from the BMR Rule IPv6 prefix. This address MUST be assigned to an interface of the MAP node and is used to terminate all MAP traffic being sent or received to the node. Port-restricted IPv4 routes are installed in the Rules table for all the Forwarding Mapping Rules, and a default route is installed to the MAP BR (see Section 5.4). Forwarding Mapping Rules are used to allow direct communication between MAP CEs, known as mesh mode. In hub and spoke mode, there are no forwarding mapping rules, all traffic MUST be forwarded directly to the BR. While an FMR is optional in the sense that a MAP CE MAY be configured with zero or more FMRs depending on the deployment, all MAP CEs MUST implement support for both rule types. 5.1. Port mapping algorithm The port mapping algorithm is used in domains whose rules allow IPv4 address sharing. The simplest way to represent a port range is using a notation similar to CIDR [RFC4632]. For example the first 256 ports are represented as port prefix 0.0/8. The last 256 ports as 255.0/8. In hexadecimal, 0x0000/8 (PSID = 0) and 0xFF00/8 (PSID = 0xFF). Using this technique, but wishing to avoid allocating the system ports [I-D.ietf-tsvwg-iana-ports] to the user, one would have to exclude the use of one or more PSIDs (e.g., PSIDs 0 to 3 in the example just given). Troan, et al. Expires April 16, 2015 [Page 8] Internet-Draft MAP October 2014 When the PSID is embedded in the End-user IPv6 prefix, then to minimize dependencies between the End-user IPv6 prefix and the assigned port-set, it is desirable to minimize the restrictions of possible PSID values. This is achieved by using an infix representation of the port value. Using such a representation, the well-known ports are excluded by restrictions on the value of the high-order bitfield (A) rather than the PSID. The infix algorithm allocates ports to a given CE as a series of contiguous ranges spaced at regular intervals throughout the complete range of possible port-set values. 0 1 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 +-----------+-----------+-------+ Ports in | A | PSID | M | the CE port-set | > 0 | | | +-----------+-----------+-------+ | a bits | k bits |m bits | Figure 2: Structure of a port-restricted port field a bits: The number of offset bits. 6 by default as this excludes the system ports (0-1023). A: Selects the range of the port number. For a > 0, A MUST be larger than 0. This ensures that the algorithm excludes the system ports. For the default value of a (6), the system ports, are excluded by requiring that A be greater than 0. Smaller values of a excludes a larger initial range. E.g., a = 4, will exclude ports 0 - 4095. The interval between successive contiguous ranges assigned to the same user is 2^a. PSID: The Port-Set Identifier (PSID). Different PSIDs guarantee non-overlapping port-sets. k bits: The length in bits of the PSID field. The sharing ratio is 2^k. The number of ports assigned to the user is 2^(16-k) - 2^m (excluded ports) M: Selects the specific port within a particular range specified by the concatenation of A and the PSID. m bits: The number of contiguous ports is given by 2^m. 5.2. Basic mapping rule (BMR) Troan, et al. Expires April 16, 2015 [Page 9] Internet-Draft MAP October 2014 The Basic Mapping Rule is mandatory, used by the CE to provision itself with an IPv4 prefix, IPv4 address or shared IPv4 address. Recall from Section 5 that the BMR consists of the following parameters: o Rule IPv6 prefix (including prefix length) o Rule IPv4 prefix (including prefix length) o Rule EA-bits length (in bits) Figure 3 shows the structure of the complete MAP IPv6 address as specified in this document. | n bits | o bits | s bits | 128-n-o-s bits | +--------------------+-----------+---------+-----------------------+ | Rule IPv6 prefix | EA bits |subnet ID| interface ID | +--------------------+-----------+---------+-----------------------+ |<--- End-user IPv6 prefix --->| Figure 3: MAP IPv6 Address Format The Rule IPv6 prefix (which is part of the End-user IPv6 prefix) that is common among all CEs using the same Basic Mapping Rule within the MAP domain. The EA bits encode the CE specific IPv4 address and port information. The EA bits, which are unique for a given Rule IPv6 prefix, can contain a full or part of an IPv4 address and, in the shared IPv4 address case, a Port-Set Identifier (PSID). An EA-bit length of 0 signifies that all relevant MAP IPv4 addressing information is passed directly in the BMR, and not derived from the End-user IPv6 prefix. The MAP IPv6 address is created by concatenating the End-user IPv6 prefix with the MAP subnet identifier (if the End-user IPv6 prefix is shorter than 64 bits) and the interface identifier as specified in Section 6. The MAP subnet identifier is defined to be the first subnet (s bits set to zero). Define: r = length of the IPv4 prefix given by the BMR; o = length of the EA bit field as given by the BMR; Troan, et al. Expires April 16, 2015 [Page 10] Internet-Draft MAP October 2014 p = length of the IPv4 suffix contained in the EA bit field. The length r MAY be zero, in which case the complete IPv4 address or prefix is encoded in the EA bits. If only a part of the IPv4 address / prefix is encoded in the EA bits, the Rule IPv4 prefix is provisioned to the CE by other means (e.g., a DHCPv6 option). To create a complete IPv4 address (or prefix), the IPv4 address suffix (p) from the EA bits, is concatenated with the Rule IPv4 prefix (r bits). The offset of the EA bits field in the IPv6 address is equal to the BMR Rule IPv6 prefix length. The length of the EA bits field (o) is given by the BMR Rule EA-bits length, and can be between 0 and 48. A length of 48 means that the complete IPv4 address and port is embedded in the End-user IPv6 prefix (a single port is assigned). A length of 0 means that no part of the IPv4 address or port is embedded in the address. The sum of the Rule IPv6 Prefix length and the Rule EA-bits length MUST be less or equal than the End-user IPv6 prefix length. If o + r < 32 (length of the IPv4 address in bits), then an IPv4 prefix is assigned. This case is shown in Figure 4. IPv4 prefix: | r bits | o bits = p bits | +-------------+---------------------+ | Rule IPv4 | IPv4 Address suffix | +-------------+---------------------+ | < 32 bits | Figure 4: IPv4 prefix If o + r is equal to 32, then a full IPv4 address is to be assigned. The address is created by concatenating the Rule IPv4 prefix and the EA-bits. This case is shown in Figure 5. Troan, et al. Expires April 16, 2015 [Page 11] Internet-Draft MAP October 2014 Complete IPv4 address: | r bits | o bits = p bits | +-------------+---------------------+ | Rule IPv4 | IPv4 Address suffix | +-------------+---------------------+ | 32 bits | Figure 5: Complete IPv4 address If o + r is > 32, then a shared IPv4 address is to be assigned. The number of IPv4 address suffix bits (p) in the EA bits is given by 32 - r bits. The PSID bits are used to create a port set. The length of the PSID bit field within EA bits is: q = o - p. Shared IPv4 address: | r bits | p bits | | q bits | +-------------+---------------------+ +------------+ | Rule IPv4 | IPv4 Address suffix | |Port-Set ID | +-------------+---------------------+ +------------+ | 32 bits | Figure 6: Shared IPv4 address The length of r MAY be 32, with no part of the IPv4 address embedded in the EA bits. This results in a mapping with no dependence between the IPv4 address and the IPv6 address. In addition the length of o MAY be zero (no EA bits embedded in the End-User IPv6 prefix), meaning that also the PSID is provisioned using e.g., the DHCP option. See Appendix A for an example of the Basic Mapping Rule. 5.3. Forwarding mapping rule (FMR) The Forwarding Mapping Rule is optional, and used in mesh mode to enable direct CE to CE connectivity. On adding an FMR rule, an IPv4 route is installed in the Rules table for the Rule IPv4 prefix. | 32 bits | | 16 bits | Troan, et al. Expires April 16, 2015 [Page 12] Internet-Draft MAP October 2014 +--------------------------+ +-------------------+ | IPv4 destination address | | IPv4 dest port | +--------------------------+ +-------------------+ : : ___/ : | p bits | / q bits : +----------+ +------------+ |IPv4 sufx| |Port-Set ID | +----------+ +------------+ \ / ____/ ________/ \ : __/ _____/ \ : / / | n bits | o bits | s bits | 128-n-o-s bits | +--------------------+-----------+---------+------------+----------+ | Rule IPv6 prefix | EA bits |subnet ID| interface ID | +--------------------+-----------+---------+-----------------------+ |<--- End-user IPv6 prefix --->| Figure 7: Deriving of MAP IPv6 address See Appendix A for an example of the Forwarding Mapping Rule. 5.4. Destinations outside the MAP domain IPv4 traffic between MAP nodes that are all within one MAP domain is encapsulated in IPv6, with the sender's MAP IPv6 address as the IPv6 source address and the receiving MAP node's MAP IPv6 address as the IPv6 destination address. To reach IPv4 destinations outside of the MAP domain, traffic is also encapsulated in IPv6, but the destination IPv6 address is set to the configured IPv6 address of the MAP BR. On the CE, the path to the BR can be represented as a point to point IPv4 over IPv6 tunnel [RFC2473] with the source address of the tunnel being the CE's MAP IPv6 address and the BR IPv6 address as the remote tunnel address. When MAP is enabled, a typical CE router will install a default IPv4 route to the BR. The BR forwards traffic received from the outside to CE's using the normal MAP forwarding rules. 6. The IPv6 Interface Identifier The Interface identifier format of a MAP node is described below. | 128-n-o-s bits | | 16 bits| 32 bits | 16 bits| +--------+----------------+--------+ Troan, et al. Expires April 16, 2015 [Page 13] Internet-Draft MAP October 2014 | 0 | IPv4 address | PSID | +--------+----+-----------+--------+ Figure 8 In the case of an IPv4 prefix, the IPv4 address field is right-padded with zeroes up to 32 bits. The PSID field is left-padded to create a 16 bit field. For an IPv4 prefix or a complete IPv4 address, the PSID field is zero. If the End-user IPv6 prefix length is larger than 64, the most significant parts of the interface identifier is overwritten by the prefix. 7. MAP Configuration For a given MAP domain, the BR and CE MUST be configured with the following MAP elements. The configured values for these elements are identical for all CEs and BRs within a given MAP domain. o The Basic Mapping Rule and optionally the Forwarding Mapping Rules, including the Rule IPv6 prefix, Rule IPv4 prefix, and Length of EA bits o Hub and spoke mode or Mesh mode. (If all traffic should be sent to the BR, or if direct CE to CE traffic should be supported). In addition the MAP CE MUST be configured with the IPv6 address(es) of the MAP BR (Section 5.4). 7.1. MAP CE The MAP elements are set to values that are the same across all CEs within a MAP domain. The values may be configured in a variety of manners, including provisioning methods such as the Broadband Forum's "TR-69" Residential Gateway management interface, an XML-based object retrieved after IPv6 connectivity is established, or manual configuration by an administrator. IPv6 DHCP options for MAP configuration is defined in [I-D.ietf-softwire-map-dhcp]. Other configuration and management methods may use the format described by this option for consistency and convenience of implementation on CEs that support multiple configuration methods. The only remaining provisioning information the CE requires in order to calculate the MAP IPv4 address and enable IPv4 connectivity is the IPv6 prefix for the CE. The End-user IPv6 prefix is configured as part of obtaining IPv6 Internet access. Troan, et al. Expires April 16, 2015 [Page 14] Internet-Draft MAP October 2014 The MAP provisioning parameters, and hence the IPv4 service itself, are tied to the associated End-user IPv6 prefix lifetime; thus, the MAP service is also tied to this in terms of authorization, accounting, etc. A single MAP CE MAY be connected to more than one MAP domain, just as any router may have more than one IPv4-enabled service provider facing interface and more than one set of associated addresses assigned by DHCP. Each domain a given CE operates within would require its own set of MAP configuration elements and would generate its own IPv4 address. Each MAP domain requires a distinct End-user IPv6 prefix. The MAP DHCP option is specified in [I-D.ietf-softwire-map-dhcp]. 7.2. MAP BR The MAP BR MUST be configured with the same MAP elements as the MAP CEs operating within the same domain. For increased reliability and load balancing, the BR IPv6 address MAY be an anycast address shared across a given MAP domain. As MAP is stateless, any BR may be used at any time. If the BR IPv6 address is anycast the relay MUST use this anycast IPv6 address as the source address in packets relayed to CEs. Since MAP uses provider address space, no specific routes need to be advertised externally for MAP to operate, neither in IPv6 nor IPv4 BGP. However, if anycast is used for the MAP IPv6 relays, the anycast addresses must be advertised in the service provider's IGP. 8. Forwarding Considerations Figure 1 depicts the overall MAP architecture with IPv4 users (N and M) networks connected to a routed IPv6 network. MAP uses Encapsulation mode as specified in [RFC2473]. For a shared IPv4 address, a MAP CE forwarding IPv4 packets from the LAN performs NAT44 functions first and creates appropriate NAT44 bindings. The resulting IPv4 packets MUST contain the source IPv4 address and source transport identifiers specified by the MAP provisioning parameters. The IPv4 packet is forwarded using the CE's MAP forwarding function. The IPv6 source and destination addresses MUST then be derived as per Section 5 of this draft. 8.1. Receiving Rules Troan, et al. Expires April 16, 2015 [Page 15] Internet-Draft MAP October 2014 A MAP CE receiving an IPv6 packet to its MAP IPv6 address sends this packet to the CE's MAP function where it is decapsulated. The resulting IPv4 packet is then forwarded to the CE's NAT44 function where it is handled according to the NAT's translation table. A MAP BR receiving IPv6 packets selects a best matching MAP domain rule (Rule IPv6 prefix) based on a longest address match of the packet's IPv6 source address, as well as a match of the packet destination address against the configured BR IPv6 address(es). The selected MAP rule allows the BR to determine the EA-bits from the source IPv6 address. To prevent spoofing of IPv4 addresses, any MAP node (CE and BR) MUST perform the following validation upon reception of a packet. First, the embedded IPv4 address or prefix, as well as PSID (if any), are extracted from the source IPv6 address using the matching MAP rule. These represent the range of what is acceptable as source IPv4 address and port. Secondly, the node extracts the source IPv4 address and port from the IPv4 packet embedded inside the IPv6 packet. If they are found to be outside the acceptable range, the packet MUST be silently discard and a counter incremented to indicate that a potential spoofing attack may be underway. The source validation checks just described are not done for packets whose source IPv6 address is that of the BR (BR IPv6 address). By default, the CE router MUST drop packets received on the MAP virtual interface (i.e., after decapsulation of IPv6) for IPv4 destinations not for its own IPv4 shared address, full IPv4 address or IPv4 prefix. 8.2. ICMP ICMP message should be supported in MAP domain. Hence, the NAT44 in MAP CE MUST implement the behavior for ICMP message conforming to the best current practice documented in [RFC5508]. If a MAP CE receives an ICMP message having ICMP identifier field in ICMP header, NAT44 in the MAP CE MUST rewrite this field to a specific value assigned from the port set. BR and other CEs must handle this field similar to the port number in the TCP/UDP header upon receiving the ICMP message with ICMP identifier field. If a MAP node receives an ICMP error message without the ICMP identifier field for errors that is detected inside a IPv6 tunnel, a node should relay the ICMP error message to the original source. This behavior SHOULD be implemented conforming to the section 8 of [RFC2473]. Troan, et al. Expires April 16, 2015 [Page 16] Internet-Draft MAP October 2014 8.3. Fragmentation and Path MTU Discovery Due to the different sizes of the IPv4 and IPv6 header, handling the maximum packet size is relevant for the operation of any system connecting the two address families. There are three mechanisms to handle this issue: Path MTU discovery (PMTUD), fragmentation, and transport-layer negotiation such as the TCP Maximum Segment Size (MSS) option [RFC0897]. MAP uses all three mechanisms to deal with different cases. 8.3.1. Fragmentation in the MAP domain Encapsulating an IPv4 packet to carry it across the MAP domain will increase its size (typically by 40 bytes). It is strongly recommended that the MTU in the MAP domain be well managed and that the IPv6 MTU on the CE WAN side interface be set so that no fragmentation occurs within the boundary of the MAP domain. Fragmentation on MAP domain entry is described in section 7.2 of [RFC2473]. The use of an anycast source address could lead to an ICMP error message generated on the path being sent to a different BR. Therefore, using dynamic tunnel MTU Section 6.7 of [RFC2473] is subject to IPv6 Path MTU black-holes. A MAP BR using an anycast source address SHOULD NOT by default use Path MTU discovery across the MAP domain. Multiple BRs using the same anycast source address could send fragmented packets to the same CE at the same time. If the fragmented packets from different BRs happen to use the same fragment ID, incorrect reassembly might occur. See [RFC4459] for an analysis of the problem. Section 3.4 suggests solving the problem by fragmenting the inner packet. 8.3.2. Receiving IPv4 Fragments on the MAP domain borders Forwarding of an IPv4 packet received from the outside of the MAP domain requires the IPv4 destination address and the transport protocol destination port. The transport protocol information is only available in the first fragment received. As described in section 5.3.3 of [RFC6346] a MAP node receiving an IPv4 fragmented packet from outside has to reassemble the packet before sending the packet onto the MAP link. If the first packet received contains the transport protocol information, it is possible to optimize this behavior by using a cache and forwarding the fragments unchanged. Implementers of MAP should be aware that there are a number of well- known attacks against IP fragmentation; see [RFC1858] and [RFC3128]. Troan, et al. Expires April 16, 2015 [Page 17] Internet-Draft MAP October 2014 Implementers should also be aware of additional issues with reassembling packets at high rates, as described in [RFC4963]. 8.3.3. Sending IPv4 fragments to the outside If two IPv4 host behind two different MAP CE's with the same IPv4 address sends fragments to an IPv4 destination host outside the domain, those hosts may use the same IPv4 fragmentation identifier, resulting in incorrect reassembly of the fragments at the destination host. Given that the IPv4 fragmentation identifier is a 16 bit field, it can be used similarly to port ranges. A MAP CE MUST rewrite the IPv4 fragmentation identifier to be within its allocated port-set. 9. NAT44 Considerations The NAT44 implemented in the MAP CE SHOULD conform with the behavior and best current practice documented in [RFC4787], [RFC5508], and [RFC5382]. In MAP address sharing mode (determined by the MAP domain /rule configuration parameters) the operation of the NAT44 MUST be restricted to the available port numbers derived via the basic mapping rule. 10. IANA Considerations This specification does not require any IANA actions. 11. Security Considerations Spoofing attacks: With consistency checks between IPv4 and IPv6 sources that are performed on IPv4/IPv6 packets received by MAP nodes, MAP does not introduce any new opportunity for spoofing attacks that would not already exist in IPv6. Denial-of-service attacks: In MAP domains where IPv4 addresses are shared, the fact that IPv4 datagram reassembly may be necessary introduces an opportunity for DOS attacks. This is inherent to address sharing, and is common with other address sharing approaches such as DS-Lite and NAT64/DNS64. The best protection against such attacks is to accelerate IPv6 deployment, so that, where MAP is supported, it is less and less used. Routing-loop attacks: This attack may exist in some automatic tunneling scenarios are documented in [RFC6324]. They cannot exist with MAP because each BRs checks that the IPv6 source address of a received IPv6 packet is a CE address based on Forwarding Mapping Rule. Troan, et al. Expires April 16, 2015 [Page 18] Internet-Draft MAP October 2014 Attacks facilitated by restricted port set: From hosts that are not subject to ingress filtering of [RFC2827], some attacks are possible by an attacker injecting spoofed packets during ongoing transport connections ([RFC4953], [RFC5961], [RFC6056]. The attacks depend on guessing which ports are currently used by target hosts, and using an unrestricted port-set is preferable, i.e., using native IPv6 connections that are not subject to MAP port range restrictions. To minimize this type of attacks when using a restricted port-set, the MAP CE's NAT44 filtering behavior SHOULD be "Address-Dependent Filtering". Furthermore, the MAP CEs SHOULD use a DNS transport proxy [RFC5625] function to handle DNS traffic, and source such traffic from IPv6 interfaces not assigned to MAP. [RFC6269] outlines general issues with IPv4 address sharing. 12. Contributors This document is the result of the IETF Softwire MAP design team effort and numerous previous individual contributions in this area: Chongfeng Xie (China Telecom) Room 708, No.118, Xizhimennei Street Beijing 100035 People's Republic of China Phone: +86-10-58552116 Email: xiechf@ctbri.com.cn Qiong Sun (China Telecom) Room 708, No.118, Xizhimennei Street Beijing 100035 People's Republic of China Phone: +86-10-58552936 Email: sunqiong@ctbri.com.cn Gang Chen (China Mobile) 53A,Xibianmennei Ave. Beijing 100053 People's Republic of China Email: chengang@chinamobile.com Yu Zhai CERNET Center/Tsinghua University Room 225, Main Building, Tsinghua University Beijing 100084 People's Republic of China Email: jacky.zhai@gmail.com Troan, et al. Expires April 16, 2015 [Page 19] Internet-Draft MAP October 2014 Wentao Shang (CERNET Center/Tsinghua University) Room 225, Main Building, Tsinghua University Beijing 100084 People's Republic of China Email: wentaoshang@gmail.com Guoliang Han (CERNET Center/Tsinghua University) Room 225, Main Building, Tsinghua University Beijing 100084 People's Republic of China Email: bupthgl@gmail.com Rajiv Asati (Cisco Systems) 7025-6 Kit Creek Road Research Triangle Park NC 27709 USA Email: rajiva@cisco.com 13. Acknowledgments This document is based on the ideas of many, including Masakazu Asama, Mohamed Boucadair, Gang Chen, Maoke Chen, Wojciech Dec, Xiaohong Deng, Jouni Korhonen, Tomasz Mrugalski, Jacni Qin, Chunfa Sun, Qiong Sun, and Leaf Yeh. The authors want in particular to recognize Remi Despres, who has tirelessly worked on generalized mechanisms for stateless address mapping. The authors would like to thank Lichun Bao, Guillaume Gottard, Dan Wing, Jan Zorz, Necj Scoberne, Tina Tsou, Kristian Poscic, and especially Tom Taylor and Simon Perreault for the thorough review and comments of this document. 14. References 14.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2473] Conta, A. and S. Deering, "Generic Packet Tunneling in IPv6 Specification", RFC 2473, December 1998. [RFC5625] Bellis, R., "DNS Proxy Implementation Guidelines", BCP 152, RFC 5625, August 2009. 14.2. Informative References [I-D.ietf-softwire-map-deployment] Troan, et al. Expires April 16, 2015 [Page 20] Internet-Draft MAP October 2014 Qiong, Q., Chen, M., Chen, G., Tsou, T., and S. Perreault, "Mapping of Address and Port (MAP) - Deployment Considerations", draft-ietf-softwire-map-deployment-03 (work in progress), October 2013. [I-D.ietf-softwire-map-dhcp] Mrugalski, T., Troan, O., Dec, W., Bao, C., leaf.yeh.sdo@gmail.com, l., and X. Deng, "DHCPv6 Options for configuration of Softwire Address and Port Mapped Clients", draft-ietf-softwire-map-dhcp-06 (work in progress), November 2013. [I-D.ietf-softwire-stateless-4v6-motivation] Boucadair, M., Matsushima, S., Lee, Y., Bonness, O., Borges, I., and G. Chen, "Motivations for Carrier-side Stateless IPv4 over IPv6 Migration Solutions", draft-ietf- softwire-stateless-4v6-motivation-05 (work in progress), November 2012. [I-D.ietf-tsvwg-iana-ports] Cotton, M., Eggert, L., Touch, J., Westerlund, M., and S. Cheshire, "Internet Assigned Numbers Authority (IANA) Procedures for the Management of the Service Name and Transport Protocol Port Number Registry", draft-ietf- tsvwg-iana-ports-10 (work in progress), February 2011. [RFC0897] Postel, J., "Domain name system implementation schedule", RFC 897, February 1984. [RFC1858] Ziemba, G., Reed, D., and P. Traina, "Security Considerations for IP Fragment Filtering", RFC 1858, October 1995. [RFC1933] Gilligan, R. and E. Nordmark, "Transition Mechanisms for IPv6 Hosts and Routers", RFC 1933, April 1996. [RFC2529] Carpenter, B. and C. Jung, "Transmission of IPv6 over IPv4 Domains without Explicit Tunnels", RFC 2529, March 1999. [RFC2663] Srisuresh, P. and M. Holdrege, "IP Network Address Translator (NAT) Terminology and Considerations", RFC 2663, August 1999. [RFC2827] Ferguson, P. and D. Senie, "Network Ingress Filtering: Defeating Denial of Service Attacks which employ IP Source Address Spoofing", BCP 38, RFC 2827, May 2000. Troan, et al. Expires April 16, 2015 [Page 21] Internet-Draft MAP October 2014 [RFC3056] Carpenter, B. and K. Moore, "Connection of IPv6 Domains via IPv4 Clouds", RFC 3056, February 2001. [RFC3128] Miller, I., "Protection Against a Variant of the Tiny Fragment Attack (RFC 1858)", RFC 3128, June 2001. [RFC3633] Troan, O. and R. Droms, "IPv6 Prefix Options for Dynamic Host Configuration Protocol (DHCP) version 6", RFC 3633, December 2003. [RFC4459] Savola, P., "MTU and Fragmentation Issues with In-the- Network Tunneling", RFC 4459, April 2006. [RFC4632] Fuller, V. and T. Li, "Classless Inter-domain Routing (CIDR): The Internet Address Assignment and Aggregation Plan", BCP 122, RFC 4632, August 2006. [RFC4787] Audet, F. and C. Jennings, "Network Address Translation (NAT) Behavioral Requirements for Unicast UDP", BCP 127, RFC 4787, January 2007. [RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless Address Autoconfiguration", RFC 4862, September 2007. [RFC4953] Touch, J., "Defending TCP Against Spoofing Attacks", RFC 4953, July 2007. [RFC4963] Heffner, J., Mathis, M., and B. Chandler, "IPv4 Reassembly Errors at High Data Rates", RFC 4963, July 2007. [RFC5214] Templin, F., Gleeson, T., and D. Thaler, "Intra-Site Automatic Tunnel Addressing Protocol (ISATAP)", RFC 5214, March 2008. [RFC5382] Guha, S., Biswas, K., Ford, B., Sivakumar, S., and P. Srisuresh, "NAT Behavioral Requirements for TCP", BCP 142, RFC 5382, October 2008. [RFC5508] Srisuresh, P., Ford, B., Sivakumar, S., and S. Guha, "NAT Behavioral Requirements for ICMP", BCP 148, RFC 5508, April 2009. [RFC5961] Ramaiah, A., Stewart, R., and M. Dalal, "Improving TCP's Robustness to Blind In-Window Attacks", RFC 5961, August 2010. Troan, et al. Expires April 16, 2015 [Page 22] Internet-Draft MAP October 2014 [RFC5969] Townsley, W. and O. Troan, "IPv6 Rapid Deployment on IPv4 Infrastructures (6rd) -- Protocol Specification", RFC 5969, August 2010. [RFC6052] Bao, C., Huitema, C., Bagnulo, M., Boucadair, M., and X. Li, "IPv6 Addressing of IPv4/IPv6 Translators", RFC 6052, October 2010. [RFC6056] Larsen, M. and F. Gont, "Recommendations for Transport- Protocol Port Randomization", BCP 156, RFC 6056, January 2011. [RFC6250] Thaler, D., "Evolution of the IP Model", RFC 6250, May 2011. [RFC6269] Ford, M., Boucadair, M., Durand, A., Levis, P., and P. Roberts, "Issues with IP Address Sharing", RFC 6269, June 2011. [RFC6324] Nakibly, G. and F. Templin, "Routing Loop Attack Using IPv6 Automatic Tunnels: Problem Statement and Proposed Mitigations", RFC 6324, August 2011. [RFC6333] Durand, A., Droms, R., Woodyatt, J., and Y. Lee, "Dual- Stack Lite Broadband Deployments Following IPv4 Exhaustion", RFC 6333, August 2011. [RFC6346] Bush, R., "The Address plus Port (A+P) Approach to the IPv4 Address Shortage", RFC 6346, August 2011. Appendix A. Examples Example 1 - Basic Mapping Rule Troan, et al. Expires April 16, 2015 [Page 23] Internet-Draft MAP October 2014 Given the MAP domain information and an IPv6 address of an endpoint: End-user IPv6 prefix: 2001:db8:0012:3400::/56 Basic Mapping Rule: {2001:db8:0000::/40 (Rule IPv6 prefix), 192.0.2.0/24 (Rule IPv4 prefix), 16 (Rule EA-bits length)} PSID length: (16 - (32 - 24) = 8. (Sharing ratio of 256) PSID offset: 6 (default) A MAP node (CE or BR) can via the BMR, or equivalent FMR, determine the IPv4 address and port-set as shown below: EA bits offset: 40 IPv4 suffix bits (p) Length of IPv4 address (32) - IPv4 prefix length (24) = 8 IPv4 address: 192.0.2.18 (0xc0000212) PSID start: 40 + p = 40 + 8 = 48 PSID length: o - p = (56 - 40) - 8 = 8 PSID: 0x34 Available ports (63 ranges) : 1232-1235, 2256-2259, ...... , 63696-63699, 64720-64723 The BMR information allows a MAP CE to determine (complete) its IPv6 address within the indicated IPv6 prefix. IPv6 address of MAP CE: 2001:db8:0012:3400:0000:c000:0212:0034 Example 2 - BR: Troan, et al. Expires April 16, 2015 [Page 24] Internet-Draft MAP October 2014 Another example can be made of a MAP BR, configured with the following FMR when receiving a packet with the following characteristics: IPv4 source address: 1.2.3.4 (0x01020304) IPv4 source port: 80 IPv4 destination address: 192.0.2.18 (0xc0000212) IPv4 destination port: 1232 Forwarding Mapping Rule: {2001:db8::/40 (Rule IPv6 prefix), 192.0.2.0/24 (Rule IPv4 prefix), 16 (Rule EA-bits length)} IPv6 address of MAP BR: 2001:db8:ffff::1 The above information allows the BR to derive as follows the mapped destination IPv6 address for the corresponding MAP CE, and also the mapped source IPv6 address for the IPv4 source address. IPv4 suffix bits (p): 32 - 24 = 8 (18 (0x12)) PSID length: 8 PSID: 0x34 (1232) The resulting IPv6 packet will have the following key fields: IPv6 source address: 2001:db8:ffff::1 IPv6 destination address: 2001:db8:0012:3400:0000:c000:0212:0034 Example 3 - Forwarding Mapping Rule: An IPv4 host behind the MAP CE (addressed as per the previous examples) corresponding with IPv4 host 1.2.3.4 will have its packets encapsulated by IPv6 using the IPv6 address of the BR configured on the MAP CE as follows: IPv6 address of BR: 2001:db8:ffff::1 IPv4 source address: 192.0.2.18 IPv4 destination address: 1.2.3.4 IPv4 source port: 1232 IPv4 destination port: 80 MAP CE IPv6 source address: 2001:db8:0012:3400:0000:c000:0212:0034 IPv6 destination address: 2001:db8:ffff::1 Troan, et al. Expires April 16, 2015 [Page 25] Internet-Draft MAP October 2014 Example 4 - Rule with no embedded address bits and no address sharing End-User IPv6 prefix: 2001:db8:0012:3400::/56 Basic Mapping Rule: {2001:db8:0012:3400::/56 (Rule IPv6 prefix), 192.0.2.18/32 (Rule IPv4 prefix), 0 (Rule EA-bits length)} PSID length: 0 (Sharing ratio is 1) PSID offset: n/a A MAP node (CE or BR) can via the BMR or equivalent FMR, determine the IPv4 address and port-set as shown below: EA bits offset: 0 IPv4 suffix bits (p): Length of IPv4 address (32) - IPv4 prefix length (32) = 0 IPv4 address: 192.0.2.18 (0xc0000212) PSID start: 0 PSID length: 0 PSID: null The BMR information allows a MAP CE also to determine (complete) its full IPv6 address by combining the IPv6 prefix with the MAP interface identifier (that embeds the IPv4 address). IPv6 address of MAP CE: 2001:db8:0012:3400:0000:c000:0201:0000 Example 5 - Rule with no embedded address bits and address sharing (sharing ratio 256) Troan, et al. Expires April 16, 2015 [Page 26] Internet-Draft MAP October 2014 End-User IPv6 prefix: 2001:db8:0012:3400::/56 Basic Mapping Rule: {2001:db8:0012:3400::/56 (Rule IPv6 prefix), 192.0.2.18/32 (Rule IPv4 prefix), 0 (Rule EA-bits length)} PSID length: 8. (From DHCP. Sharing ratio of 256) PSID offset: 6 (Default) PSID : 0x34 (From DHCP.) A MAP node can via the Basic Mapping Rule determine the IPv4 address and port-set as shown below: EA bits offset: 0 IPv4 suffix bits (p): Length of IPv4 address (32) - IPv4 prefix length (32) = 0 IPv4 address: 192.0.2.18 (0xc0000212) PSID offset: 6 PSID length: 8 PSID: 0x34 Available ports (63 ranges) : 1232-1235, 2256-2259, ...... , 63696-63699, 64720-64723 The Basic Mapping Rule information allows a MAP CE also to determine (complete) its full IPv6 address by combining the IPv6 prefix with the MAP interface identifier (that embeds the IPv4 address and PSID). IPv6 address of MAP CE: 2001:db8:0012:3400:0000:c000:0212:0034 Note that the IPv4 address and PSID is not derived from the IPv6 prefix assigned to the CE, but provisioned separately using e.g., DHCP. Appendix B. A More Detailed Description of the Derivation of the Port Mapping Algorithm This Appendix describes how the port mapping algorithm described in Section 5.1 was derived. The algorithm is used in domains whose rules allow IPv4 address sharing. The basic requirement for a port mapping algorithm is that the port- sets it assigns to different MAP CEs MUST be non-overlapping. A number of other requirements guided the choice of the algorithm: Troan, et al. Expires April 16, 2015 [Page 27] Internet-Draft MAP October 2014 o In keeping with the general MAP algorithm the port-set MUST be derivable from a port-set identifier (PSID) that can be embedded in the End-user IPv6 prefix. o The mapping MUST be reversible, such that, given the port number, the PSID of the port-set to which it belongs can be quickly derived. o The algorithm MUST allow a broad range of address sharing ratios. o It SHOULD be possible to exclude subsets of the complete port numbering space from assignment. Most operators would exclude the system ports (0-1023). A conservative operator might exclude all but the transient ports (49152-65535). o The effect of port exclusion on the possible values of the End- user IPv6 prefix (i.e., due to restrictions on the PSID value) SHOULD be minimized. o For administrative simplicity, the algorithm SHOULD allocate the the same or almost the same number of ports to each CE sharing a given IPv4 address. The two extreme cases that an algorithm satisfying those conditions might support are: (1) the port numbers are not contiguous for each PSID, but uniformly distributed across the allowed port range; (2) the port numbers are contiguous in a single range for each PSID. The port mapping algorithm proposed here is called the Generalized Modulus Algorithm (GMA) and supports both these cases. For a given IPv4 address sharing ratio (R) and the maximum number of contiguous ports (M) in a port-set, the GMA is defined as: a. The port numbers (P) corresponding to a given PSID are generated by: (1) ... P = (R * M) * i + M * PSID + j where i and j are indices and the ranges of i, j, and the PSID are discussed in a moment. b. For any given port number P, the PSID is calculated as: (2) ... PSID = trunc((P modulo (R * M)) / M) Troan, et al. Expires April 16, 2015 [Page 28] Internet-Draft MAP October 2014 where trunc() is the operation of rounding down to the nearest integer. Formula (1) can be interpreted as follows. First, the available port space is divided into blocks of size R * M. Each block is divided into R individual ranges of length M. The index i in formula (1) selects a block, PSID selects a range within that block, and the index j selects a specific port value within the range. On the basis of this interpretation: o i ranges from ceil(N / (R * M)) to trunc(65536/(R * M)) - 1, where ceil is the operation of rounding up to the nearest integer and N is the number of ports (e.g., 1024) excluded from the lower end of the range. That is, any block containing excluded values is discarded at the lower end, and if the final block has fewer than R * M values it is discarded. This ensures that the same number of ports is assigned to every PSID. o PSID ranges from 0 to R - 1; o j ranges from 0 to M - 1. B.1. Bit Representation of the Algorithm If R and M are powers of 2 (R = 2^k, M = 2^m), formula (1) translates to a computationally convenient structure for any port number represented as a 16-bit binary number. This structure is shown in Figure 9. 0 8 15 +---------------+----------+------+-------------------+ | P | ----------------+-----------------+-------------------+ | i | PSID | j | +---------------+----------+------+-------------------+ |<----a bits--->|<-----k bits---->|<------m bits----->| Figure 9: Bit Representation of a Port Number As shown in the figure, the index value i of formula (1) is given by the first a = 16 - k - m bits of the port number. The PSID value is given by the next k bits, and the index value j is given by the last m bits. For any port number, the PSID can be obtained by a bit mask operation. Troan, et al. Expires April 16, 2015 [Page 29] Internet-Draft MAP October 2014 Note that when M and R are powers of 2, 65536 divides evenly by R * M. Hence the final block is complete and the upper bound on i is exactly 65536/(R * M) - 1. The lower bound on i is still the minimum required to ensure that the required set of ports is excluded. No port numbers are wasted through discarding of blocks at the lower end if block size R * M is a factor of N, the number of ports to be excluded. As a final note, the number of blocks into which the range 0-65535 is being divided in the above representation is given by 2^a. Hence the case where a = 0 can be interpreted as one where the complete range has been divided into a single block, and individual port-sets are contained in contiguous ranges in that block. We cannot throw away the whole block in that case, so port exclusion has to be achieved by putting a lower bound equal to ceil(N / M) on the allowed set of PSID values instead. B.2. GMA examples For example, for R = 256, PSID = 0, offset: a = 6 and PSID length: k = 8 bits Available ports (63 ranges) : 1024-1027, 2048-2051, ...... , 63488-63491, 64512-64515 Example 1: with offset = 6 (a = 6) For example, for R = 64, PSID = 0, a = 0 (PSID offset = 0 and PSID length = 6 bits), no port exclusion: Available ports (1 range) : 0-1023 Example 2: with offset = 0 (a = 0) and N = 0 Authors' Addresses Ole Troan (editor) Cisco Systems Philip Pedersens vei 1 Lysaker 1366 Norway Email: ot@cisco.com Troan, et al. Expires April 16, 2015 [Page 30] Internet-Draft MAP October 2014 Wojciech Dec Cisco Systems Haarlerbergpark Haarlerbergweg 13-19 Amsterdam, NOORD-HOLLAND 1101 CH Netherlands Email: wdec@cisco.com Xing Li CERNET Center/Tsinghua University Room 225, Main Building, Tsinghua University Beijing 100084 People's Republic of China Email: xing@cernet.edu.cn Congxiao Bao CERNET Center/Tsinghua University Room 225, Main Building, Tsinghua University Beijing 100084 People's Republic of China Email: congxiao@cernet.edu.cn Satoru Matsushima SoftBank Telecom 1-9-1 Higashi-Shinbashi, Munato-ku Tokyo Japan Email: satoru.matsushima@g.softbank.co.jp Tetsuya Murakami IP Infusion 1188 East Arques Avenue Sunnyvale USA Email: tetsuya@ipinfusion.com Troan, et al. Expires April 16, 2015 [Page 31] Internet-Draft MAP October 2014 Tom Taylor (editor) Huawei Technologies Ottawa Canada Email: tom.taylor.stds@gmail.com Troan, et al. Expires April 16, 2015 [Page 32]