Network Working Group E. Gray Internet-Draft Ericsson Updates: 4379 (if approved) N. Bahadur Intended status: Standards Track Juniper Networks, Inc. Expires: March 30, 2012 S. Boutros Cisco Systems, Inc. R. Aggarwal September 27, 2011 MPLS On-demand Connectivity Verification and Route Tracing draft-ietf-mpls-tp-on-demand-cv-07 Abstract Label Switched Path Ping (LSP-Ping) is an existing and widely deployed Operations, Administration and Maintenance (OAM) mechanism for Multi-Protocol Label Switching (MPLS) Label Switched Paths (LSPs). This document describes extensions to LSP-Ping so that LSP- Ping can be used for On-demand Connectivity Verification of MPLS Transport Profile (MPLS-TP) LSPs and Pseudowires. This document also clarifies procedures to be used for processing the related OAM packets. Further, it describes procedures for using LSP-Ping to perform Connectivity Verification and Route Tracing functions in MPLS-TP networks. Finally this document updates RFC 4379 by adding a new address type and requesting an IANA registry. Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on March 30, 2012. Copyright Notice Copyright (c) 2011 IETF Trust and the persons identified as the document authors. All rights reserved. Gray, et al. Expires March 30, 2012 [Page 1] Internet-Draft MPLS On-demand Connectivity Verification September 2011 This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1. Conventions used in this document . . . . . . . . . . . . 4 1.2. On-demand CV for MPLS-TP LSPs using IP encapsulation . . . 5 1.3. On-demand CV for MPLS-TP LSPs using non-IP encapsulation . . . . . . . . . . . . . . . . . . . . . . 5 2. LSP-Ping Extensions . . . . . . . . . . . . . . . . . . . . . 5 2.1. New address type for Downstream Mapping TLV . . . . . . . 5 2.1.1. DSMAP/DDMAP Non-IP Address Information . . . . . . . . 6 2.2. Source/Destination Identifier TLV . . . . . . . . . . . . 7 2.2.1. Source/Destination Identifier TLV Format . . . . . . . 7 2.2.2. Source Identifier TLV . . . . . . . . . . . . . . . . 8 2.2.3. Destination Identifier TLV . . . . . . . . . . . . . . 8 2.3. Identifying Statically provisioned LSPs and PWs . . . . . 8 2.3.1. Static LSP Sub-TLV . . . . . . . . . . . . . . . . . . 9 2.3.2. Static Pseudowire Sub-TLV . . . . . . . . . . . . . . 9 3. Performing On-demand CV over MPLS-TP LSPs . . . . . . . . . . 10 3.1. LSP-Ping with IP encapsulation . . . . . . . . . . . . . . 11 3.2. On-demand CV with IP encapsulation, over ACH . . . . . . . 11 3.3. Non-IP based On-demand CV, using ACH . . . . . . . . . . . 12 3.4. Reverse Path Connectivity Verification . . . . . . . . . . 12 3.4.1. Requesting Reverse Path Connectivity Verification . . 13 3.4.2. Responder Procedures . . . . . . . . . . . . . . . . . 13 3.4.3. Requester Procedures . . . . . . . . . . . . . . . . . 14 3.5. P2MP Considerations . . . . . . . . . . . . . . . . . . . 14 3.6. Management Considerations for Operation with Static MPLS-TP . . . . . . . . . . . . . . . . . . . . . . . . . 14 3.7. GAL Label Processing . . . . . . . . . . . . . . . . . . . 14 4. Performing on-demand Route Tracing over MPLS-TP LSPs . . . . . 15 4.1. On-demand LSP Route Tracing with IP encapsulation . . . . 15 4.2. Non-IP based On-demand LSP Route Tracing, using ACH . . . 15 4.2.1. Requester procedure for sending echo request packets . . . . . . . . . . . . . . . . . . . . . . . 15 4.2.2. Requester procedure for receiving echo response packets . . . . . . . . . . . . . . . . . . . . . . . 16 4.2.3. Responder procedure . . . . . . . . . . . . . . . . . 16 Gray, et al. Expires March 30, 2012 [Page 2] Internet-Draft MPLS On-demand Connectivity Verification September 2011 4.3. P2MP Considerations . . . . . . . . . . . . . . . . . . . 16 4.4. ECMP Considerations . . . . . . . . . . . . . . . . . . . 16 5. Applicability . . . . . . . . . . . . . . . . . . . . . . . . 16 6. Security Considerations . . . . . . . . . . . . . . . . . . . 16 7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 17 7.1. New Source and Destination Identifier TLVs . . . . . . . . 17 7.2. New Target FEC Stack Sub-TLVs . . . . . . . . . . . . . . 17 7.3. New Reverse-path Target FEC Stack TLV . . . . . . . . . . 17 7.4. New Pseudowire Associated Channel Type . . . . . . . . . . 18 7.5. New RFC 4379 Registry . . . . . . . . . . . . . . . . . . 18 8. Contributing Authors and Acknowledgements . . . . . . . . . . 19 9. References . . . . . . . . . . . . . . . . . . . . . . . . . . 19 9.1. Normative References . . . . . . . . . . . . . . . . . . . 19 9.2. Informative References . . . . . . . . . . . . . . . . . . 20 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 21 Gray, et al. Expires March 30, 2012 [Page 3] Internet-Draft MPLS On-demand Connectivity Verification September 2011 1. Introduction Label Switched Path Ping (LSP-Ping) [RFC4379] is an Operations, Administration and Maintenance (OAM) mechanism for Multi-Protocol Label Switching (MPLS) Label Switched Paths (LSPs). This document describes extensions to LSP-Ping so that LSP-Ping can be used for on- demand monitoring of MPLS Transport Profile (MPLS-TP) LSPs and Pseudowires. It also clarifies the procedures to be used for processing the related OAM packets. This document describes how LSP- Ping can be used for on-demand Connectivity Verification (Section 3) and Route Tracing (Section 4) functions required in [RFC5860] and specified in [RFC6371]. 1.1. Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. There is considerable opportunity for confusion in use of the terms "on-demand connectivity verification" (CV), "on-demand route tracing" and "LSP-Ping." In this document, we try to use the terms consistently as follows: o LSP-Ping: refers to the mechanism - particularly as defined and used in referenced material; o On-demand CV: refers to on-demand connectivity verification and - where both apply equally - on-demand route tracing, as implemented using the LSP-Ping mechanism extended for support of MPLS-TP; o On-demand route tracing: used in those cases where the LSP-Ping mechanism (as extended) is used exclusively for route tracing. From the perspective of on-demand CV and route tracing, we use the concepts of "Requester" and "Responder" as follows: o Requester: Originator of an OAM Request message, o Responder: Entity responding to an OAM Request message. Since - in this document - all messages are assumed to be carried in an LSP, all Request messages would be injected at the ingress to an LSP. A Responder might or might not be at the egress of this same LSP, given that it could receive Request messages as a result of TTL expiry. If a Reply is to be delivered via a reverse path LSP, the message would again be inserted at the ingress of that LSP. Gray, et al. Expires March 30, 2012 [Page 4] Internet-Draft MPLS On-demand Connectivity Verification September 2011 1.2. On-demand CV for MPLS-TP LSPs using IP encapsulation LSP-Ping requires IP addressing on responding Label Switching Routers (LSRs) for performing OAM on MPLS signaled LSPs and pseudowires. In particular, in these cases, LSP-Ping packets generated by a Requester are encapsulated in an IP/UDP header with the destination address from the 127/8 range and then encapsulated in the MPLS label stack ([RFC4379] , [RFC5884]). A Responder uses the presence of the 127/8 destination address to identify OAM packets and relies further on the UDP port number to determine whether the packet is a LSP-Ping packet. It is to be noted that this determination does not require IP forwarding capabilities. It requires the presence of an IP host stack which enables responding LSRs to process packets with a destination address from the 127/8 range. [RFC1122] allocates the 127/8 range as "Internal host loopback address" and [RFC1812] states that "a router SHOULD NOT forward, except over a loopback interface, any packet that has a destination address on network 127". 1.3. On-demand CV for MPLS-TP LSPs using non-IP encapsulation In certain MPLS-TP deployment scenarios IP addressing might not be available or it might be preferred to use some form of non-IP encapsulation for On-demand CV, route tracing and BFD packets. In such scenarios, On-demand CV and/or route tracing SHOULD be run without IP addressing, using the Associated Channel (ACH) channel type specified in Section 3. Section 3.3 and Section 4.2 describe the theory of operation for performing On-demand CV over MPLS-TP LSPs with any non-IP encapsulation. 2. LSP-Ping Extensions 2.1. New address type for Downstream Mapping TLV [RFC4379] defines the Downstream Mapping (DSMAP) TLV. [I-D.ietf-mpls-lsp-ping-enhanced-dsmap] further defines the Downstream Detailed Mapping (DDMAP) TLV. This document defines the following new address type which MAY be used in any DSMAP or DDMAP TLV included in an On-demand CV message: Type # Address Type K Octets ------ -------------- -------- 5 Non IP 12 Figure 1: Downstream Mapping TLV new address type Gray, et al. Expires March 30, 2012 [Page 5] Internet-Draft MPLS On-demand Connectivity Verification September 2011 The new address type indicates that no address is present in the DSMAP or DDMAP TLV. However, IF_Num information (see definition of "IF_NUM" in [RFC6370]) for both ingress and egress interfaces, as well as multipath information is included in the format and MAY be present. IF_Num values of zero indicate that no IF_Num applies in the field in which this value appears. Multipath type SHOULD be set to 0 (no multipath) when using this address type. When this address type is used, on receipt of a LSP-Ping echo request, interface verification MUST be bypassed. Thus the receiving node SHOULD only perform MPLS label control-plane/data-plane consistency checks. Note that these consistency checks include checking of included identifier information. The new address type is also applicable to the Detailed Downstream Mapping (DDMAP) TLV defined in [I-D.ietf-mpls-lsp-ping-enhanced-dsmap]. 2.1.1. DSMAP/DDMAP Non-IP Address Information If the DSMAP (or DDMAP) TLV is included when sending On-demand CV packets using ACH, without IP encapsulation, the following information MUST be included in any DSMAP or DDMAP TLV that is included in the packet. This information forms the address portion of the DSMAP TLV (as defined in [RFC4379]) or DDMAP TLV (as defined in [I-D.ietf-mpls-lsp-ping-enhanced-dsmap] using one of the address information fields defined in [RFC4379] and extended to include non-IP identifier types in this document). 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MTU | Address Type | DS Flags | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Ingress IF_Num (4 octets) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Egress IF_Num (4 octets) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Multipath Type| Depth Limit | Multipath Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 2: New DSMAP/DDMAP Address Format Address Type will be 5 (as shown in Section 2.1 above. Gray, et al. Expires March 30, 2012 [Page 6] Internet-Draft MPLS On-demand Connectivity Verification September 2011 Ingress IF_Num identifies the ingress interface on the target node. A value of 0 indicates that the interface is not part of the identifier. Egress IF_Num identifies the egress interface on the target node. A value of 0 indicates that the interface is not part of the identifier. Multipath type SHOULD be set to 0 (no multipath) when using this address type. Including this TLV, with one or the other IF_Num (but not both) set to a non-zero value, in a request message that also includes a destination identifier TLV (as described in section 2.2.3), is sufficient to identify the "per-interface" MIP in section 7.3 of [RFC6370]. Inclusion of this TLV with both IF_Num fields set to zero would be interpretted as specifying neither an ingress, nor an egress, interface. Note that this is the same as not including the TLV, hence including this TLV with both IF_Num values set to zero is NOT RECOMMENDED. Including this TLV with both IF_NUM fields set to a non-zero value will result in the responder sending a Return Code of 5 ("Downstream Mapping Mis-match") if either IF_Num is incorrect for this LSP or PW. 2.2. Source/Destination Identifier TLV 2.2.1. Source/Destination Identifier TLV Format The format for the identifier TLV is the same for both Source and Destination Identifier TLVs (only the type is different). The format is as specified in the figure below. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length = 8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Global_ID (4 Octets) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Node_ID (4 Octets) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 3: New Source/Destination Identifier Format Gray, et al. Expires March 30, 2012 [Page 7] Internet-Draft MPLS On-demand Connectivity Verification September 2011 Type will be one of either TBD-SRC or TBD-DST, depending on whether the TLV in question is a Source or Destination Identifier TLV. Global_ID is as defined in [RFC6370]. Node_ID is as defined in [RFC6370]. 2.2.2. Source Identifier TLV When sending On-demand CV packets using ACH, without IP encapsulation, there MAY be a need to identify the source of the packet. This source identifier will be specified via the Source Identifier TLV, using the Identifier TLV defined in Section 2.2.1, containing the information specified above. An On-demand CV packet MUST NOT include more than 1 Source Identifier TLV. The Source Identifier TLV MUST specify the identifier of the originator of the packet. If more than 1 such TLV is present in an On-demand CV request packet, then an error of 1 (Malformed echo request received, Section 3.3 [RFC4379]) MUST be returned, if it is possible to unambiguously identify the source of the packet. 2.2.3. Destination Identifier TLV When sending On-demand CV packets using ACH, without IP encapsulation, there MAY be a need to identify the destination of the packet. This destination identifier will be specified via the Destination Identifier TLV, using the Identifier TLV defined in Section 2.2.1, containing the information specified above. An On-demand CV packet MUST NOT include more than 1 Destination Identifier TLV. The Destination Identifier TLV MUST specify the destination node for the packet. If more than 1 such TLV is present in an On-demand CV Request packet, then an error of 1 (Malformed echo request received, Section 3.3 [RFC4379]) MUST be returned, if it is possible to unambiguously identify the source of the packet. 2.3. Identifying Statically provisioned LSPs and PWs [RFC4379] specifies how an MPLS LSP under test is identified in an echo request. A Target FEC Stack TLV is used to identify the LSP. In order to identify a statically provisioned LSP and PW, new target FEC stack sub-TLVs are being defined. The new sub-TLVs are assigned sub-type identifiers as follows, and are described in the following sections. Gray, et al. Expires March 30, 2012 [Page 8] Internet-Draft MPLS On-demand Connectivity Verification September 2011 Type # Sub-Type # Length Value Field ------ ---------- ------ ----------- 1 22 24 Static LSP 1 23 32 Static Pseudowire Figure 4: New target FEC sub-types 2.3.1. Static LSP Sub-TLV The format of the Static LSP sub-TLV value field is specified in the following figure. The value fields are taken from the definitions in [RFC6370]. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Global ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Node ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Tunnel Number | LSP Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Destination Global ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Destination Node ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Destination Tunnel Number | Must be Zero | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 5: Static LSP FEC Sub-TLV The Source Global ID and Destination Global ID MAY be set to 0. When set to zero, the field is not applicable. 2.3.2. Static Pseudowire Sub-TLV The format of the Static PW sub-TLV value field is specified in the following figure. Gray, et al. Expires March 30, 2012 [Page 9] Internet-Draft MPLS On-demand Connectivity Verification September 2011 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + Service Identifier + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Global ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Node ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source AC-ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Destination Global ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Destination Node ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Destination AC-ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 6: Static PW FEC Sub-TLV Service Identifier is a 64-bit unsigned integer, that is included in the first two words, as shown. The Service Identifier identifies the service associated with the transport path under test. The value MAY - for example - be an Attachment Group Identifier (AGI), type 0x01, as defined in [RFC4446]. The Source Global ID and Destination Global ID MAY be set to 0. When either of these fields is set to zero, the corresponding Global ID is not applicable. This might be done in a scenario where local scope is sufficient for uniquely identifying services. The Global ID and Node ID fields are defined in [RFC6370]. The AC-ID fields are defined in [RFC5003]. 3. Performing On-demand CV over MPLS-TP LSPs This section specifies how On-demand CV can be used in the context of MPLS-TP LSPs. The On-demand CV function meets the On-demand Connectivity Verification requirements specified in [RFC5860], section 2.2.3. This function SHOULD NOT be performed except in the on-demand mode. This function SHOULD be performed between End Points (MEPs) and Intermediate Points (MIPs) of PWs and LSPs, and between End Points of PWs, LSPs and Sections. In order for the On-demand CV packet to be processed at the desired MIP, the TTL of the MPLS label Gray, et al. Expires March 30, 2012 [Page 10] Internet-Draft MPLS On-demand Connectivity Verification September 2011 MUST be set such that it expires at the MIP to be probed. [RFC5586] defines an ACH mechanism for MPLS LSPs. The mechanism is a generalization of Associated Channel mechanism that [RFC4385] defined for use with Pseudowires. As a result, it is possible to use a single Associated Channel Type for either an LSP or Pseudowire. A new Pseudowire Associated Channel Type (type TBD-2) is defined for use in performing On-demand Connectivity Verification. Its use is described in the following sections. ACH TLVs SHALL NOT be associated with this channel type. Except as specifically stated in the sections below, message and TLV construction procedures for On-demand CV messages are as defined in [RFC4379]. 3.1. LSP-Ping with IP encapsulation LSP-Ping packets, as specified in [RFC4379], are sent over the MPLS LSP for which OAM is being performed and contain an IP/UDP packet within them. The IP header is not used for forwarding (since LSP forwarding is done using MPLS label switching). The IP header is used mainly for addressing and can be used in the context of MPLS-TP LSPs. This form of On-demand CV OAM MUST be supported for MPLS-TP LSPs when IP addressing is in use. The On-demand CV echo response message MUST be sent on the reverse path of the LSP. The reply MUST contain IP/UDP headers followed by the On-demand CV payload. The destination address in the IP header MUST be set to that of the sender of the echo request message. The source address in the IP header MUST be set to a valid address of the replying node. 3.2. On-demand CV with IP encapsulation, over ACH IP encapsulated On-demand CV packets MAY be sent over the MPLS LSP using the control channel (ACH). IP ACH type specified in [RFC4385] MUST be used in such a case. The IP header is used mainly for addressing and can be used in the context of MPLS-TP LSPs. The On-demand CV echo response message MUST be sent on the reverse path of the LSP. The response in this case SHOULD use ACH and SHOULD be IP encapsulated. If IP encapsulated, the destination address in the IP header MUST be set to that of the sender of the echo request message, and the source address in the IP header MUST be set to a valid address of the Gray, et al. Expires March 30, 2012 [Page 11] Internet-Draft MPLS On-demand Connectivity Verification September 2011 replying node. 3.3. Non-IP based On-demand CV, using ACH The OAM procedures defined in [RFC4379] require the use of IP addressing, and in some cases IP routing, to perform OAM functions. When the ACH header is used, IP addressing and routing is not needed. This section describes procedures for performing on-demand CV without a dependency on IP addressing and routing. In the non-IP case, when using On-demand CV via LSP-Ping with the ACH header, the On-demand CV request payload MUST directly follow the ACH header, and the LSP-Ping Reply mode [RFC4379] in the LSP-Ping echo request SHOULD be set to 4 (Reply via application level control channel). Note that the application level control channel in this case is the reverse path of the LSP (or Pseudowire) using ACH. The requesting node MAY attach a Source Identifier TLV (Section 2.2) to identify the node originating the request. If the Reply mode indicated in an On-demand CV Request is 4 (Reply via application level control channel), the On-demand CV reply message MUST be sent on the reverse path of the LSP using ACH. The On-demand CV payload MUST directly follow the ACH header and IP and/or UDP headers MUST NOT be attached. The responding node MAY attach a Source Identifier TLV to identify the node sending the response. If a node receives an MPLS echo request packet over ACH, without IP/ UDP headers, with a reply mode of 4, and if that node does not have a return MPLS LSP path to the echo request source, then the node SHOULD drop the echo request packet and not attempt to send a response. If a node receives an MPLS echo request with a reply mode other than 4 (reply via application level control channel), and if the node supports that reply mode, then it MAY respond using that reply mode. If the node does not support the reply mode requested, or is unable to reply using the requested reply mode in any specific instance, the node MUST drop the echo request packet and not attempt to send a response. 3.4. Reverse Path Connectivity Verification Gray, et al. Expires March 30, 2012 [Page 12] Internet-Draft MPLS On-demand Connectivity Verification September 2011 3.4.1. Requesting Reverse Path Connectivity Verification A new Global flag, Validate Reverse Path (R), is being defined in the LSP-Ping packet header. When this flag is set in the echo request, the Responder SHOULD return reverse path FEC information, as described in Section 3.4.2. The R flag MUST NOT be set in the echo response. The Global Flags field is now a bit vector with the following format: 0 1 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MBZ |R|T|V| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 7: Global Flags Field The V flag is defined in [RFC4379]. The T flag is defined in [I-D.ietf-mpls-p2mp-lsp-ping]. The R flag is defined in this draft. The Validate FEC Stack (V) flag MAY be set in the echo response when reverse path connectivity verification is being performed. 3.4.2. Responder Procedures When the R flag is set in the echo request, the responding node SHOULD attach a Reverse-path Target FEC Stack TLV in the echo response. The requesting node (on receipt of the response) can use the Reverse-path Target FEC Stack TLV to perform reverse path connectivity verification. For co-routed bi-directional LSPs, the Reverse-path Target FEC Stack used for On-demand CV will be the same in both the forward and reverse path of the LSP. For associated bi- directional LSPs, the target FEC stack MAY be different for the reverse path. The format of the Reverse-path Target FEC Stack TLV is the same as that of the Target FEC stack TLV defined in [RFC4379]. The rules for creating a Target FEC stack TLV also apply to the Reverse-path Target FEC Stack TLV. Value TLV -------- ------------------------------------ TBD-1 Reverse-path Target FEC Stack Gray, et al. Expires March 30, 2012 [Page 13] Internet-Draft MPLS On-demand Connectivity Verification September 2011 Figure 8: Reverse-Path Target FEC Stack TLV Type 3.4.3. Requester Procedures On receipt of the echo response, the requesting node MUST perform the following checks: 1. Perform interface and label-stack validation to ensure that the packet is received on the reverse path of the bi-directional LSP 2. If the Reverse-Path Target FEC Stack TLV is present in the echo response, then perform FEC validation. The verification in this case is performed as described for Target FEC Stack in section 3.6 of [RFC4379]. If any of the validations fail, then the requesting node MUST drop the echo response and SHOULD log and/or report an error. 3.5. P2MP Considerations [I-D.ietf-mpls-p2mp-lsp-ping] describes how LSP-Ping can be used for OAM on P2MP LSPs with IP encapsulation. This MUST be supported for MPLS-TP P2MP LSPs when IP addressing is used. When IP addressing is not used, then the procedures described in Section 3.3 can be applied to P2MP MPLS-TP LSPs as well. 3.6. Management Considerations for Operation with Static MPLS-TP Support for static MPLS-TP LSP, or Pseudowire, usage and on-demand CV, MAY require manageable objects to allow, for instance, configuring operating parameters such as identifiers associated with a statically configured LSP or PW. The specifics of this manageability requirement are out-of-scope in this document and SHOULD be addressed in appropriate management specifications. 3.7. GAL Label Processing At the Requester, when encapsulating the LSP echo request (LSP Ping) packet (with the IP ACH, or the non IP ACH, codepoint), a GAL label MUST be added before adding the MPLS LSP label, and sending the LSP Ping echo request packet in-band in the MPLS LSP. The GAL label MUST NOT be considered as part of the MPLS label stack that requires verification by the Responder. For this reason, a NIL FEC Stack TLV MUST NOT be added or associated with the GAL label. Gray, et al. Expires March 30, 2012 [Page 14] Internet-Draft MPLS On-demand Connectivity Verification September 2011 The GAL Label MUST NOT be included in DSMAP or DDMAP TLVs. Interface and label stack TLVs MUST include the whole label stack including the GAL label. 4. Performing on-demand Route Tracing over MPLS-TP LSPs This section specifies how On-demand CV route tracing can be used in the context of MPLS-TP LSPs. The On-demand CV route tracing function meets the Route Tracing requirement specified in [RFC5860], section 2.2.4. This function SHOULD be performed on-demand. This function SHOULD be performed between End Points and Intermediate Points of PWs and LSPs, and between End Points of PWs, LSPs and Sections. When performing On-demand CV route tracing, the requesting node inserts a Downstream Mapping TLV to get the downstream node information and to enable LSP verification along the transit nodes. The Downstream Mapping TLV can be used as is for performing route tracing. If IP addressing is not in use, then the Address Type field in the Downstream Mapping TLV can be set to "Non IP" (Section 2.1). The Downstream Mapping TLV address type field can be extended to include other address types as need be. 4.1. On-demand LSP Route Tracing with IP encapsulation The mechanics of On-demand CV route tracing are similar to those described for ping in Section 3.1. On-demand Route Tracing packets sent by the Requester MUST follow procedures described in [RFC4379]. This form of On-demand CV OAM MUST be supported for MPLS-TP LSPs, when IP addressing is used. 4.2. Non-IP based On-demand LSP Route Tracing, using ACH This section describes procedures for performing LSP route tracing when using LSP-Ping with the ACH header and without any dependency on IP addressing. The procedures specified in Section 3.3 with regards to Source Idenfier TLV apply to LSP route tracing as well. 4.2.1. Requester procedure for sending echo request packets On-demand Route Tracing packets sent by the Requester MUST adhere to the format described in Section 3.3. MPLS-TTL expiry (as described in [RFC4379]) will be used to direct the packets to specific nodes along the LSP path. Gray, et al. Expires March 30, 2012 [Page 15] Internet-Draft MPLS On-demand Connectivity Verification September 2011 4.2.2. Requester procedure for receiving echo response packets The On-demand CV route tracing responses will be received on the LSP itself and the presence of an ACH header with channel type of On- demand CV is an indicator that the packet contains an On-demand CV payload. 4.2.3. Responder procedure When a echo request reaches the Responder, the presence of the ACH channel type of On-demand CV will indicate that the packet contains On-demand CV data. The On-demand CV data, the label stack and the destination identifier are sufficient to identify the LSP associated with the echo request packet. If there is an error and the node is unable to identify the LSP on which the echo response would be sent, the node MUST drop the echo request packet and not send any response back. All responses MUST always be sent on a LSP path using the ACH header and ACH channel type of On-demand CV. 4.3. P2MP Considerations [I-D.ietf-mpls-p2mp-lsp-ping] describes how LSP-Ping can be used for OAM on P2MP LSPs. This MUST be supported for MPLS-TP P2MP LSPs when IP addressing is used. When IP addressing is not used, then the procedures described in Section 4.2 can be applied to P2MP MPLS-TP LSPs as well. 4.4. ECMP Considerations On-demand CV using ACH SHOULD NOT be used when there is ECMP (equal cost multiple paths) for a given LSP. The addition of the additional ACH header can modify the hashing behavior for OAM packets which could result in incorrect monitoring of path taken by data traffic. 5. Applicability The procedures specified in this document for non-IP encapsulation apply to MPLS-TP Transport paths. This includes LSPs and PWs when IP encapsulation is not desired. However, when IP addressing is used, as in non MPLS-TP LSPs, procedures specified in [RFC4379] MUST be used. 6. Security Considerations The draft does not itself introduce any new security considerations. Those discussed in [RFC4379] are also applicable to this document. Gray, et al. Expires March 30, 2012 [Page 16] Internet-Draft MPLS On-demand Connectivity Verification September 2011 Unlike typical deployment scenarios identified in [RFC4379], however, likely deployments of on-demand CV for transport paths involves a strong possibility that the techniques in this document may be used across MPLS administrative boundaries. Where this may occur, it is RECOMMENDED that on-demand OAM is configured as necessary to ensure that Source Identifier TLVs are included in on-demand CV messages. This will allow implementations to filter OAM messages arriving from an unexpected or unknown source. 7. IANA Considerations 7.1. New Source and Destination Identifier TLVs IANA is requested to assign the following TLV types from the "Label Switched Paths (LSPs) Ping Parameters - TLVs" Registry, "TLVs and sub-TLVs" sub-registry (from "Standards Action" TLV type range): Length Type # TLV Name Octets Reference ------ -------------------- ------ ------------------------ TBD-SRC Source ID TLV 8 this document (sect 2.2) TBD-DST Destination ID TLV 8 this document (sect 2.2) Figure 9: New Source/Destination Identifier TLV Type 7.2. New Target FEC Stack Sub-TLVs Section 2.3 defines 2 new sub-TLV types for inclusion within the LSP Ping [RFC4379] Target FEC Stack TLV. IANA is requested to assign sub-type values to the following sub-TLVs from the "Multiprotocol Label Switching Architecture (MPLS) Label Switched Paths (LSPs) Ping Parameters - TLVs" registry, "TLVs and sub-TLVs" sub-registry. Value Meaning Reference ----- ------------------------- -------------------------- 22 Static LSP sub-TLV this document (sect 2.4.1) 23 Static Pseudowire sub-TLV this document (sect 2.4.2) 7.3. New Reverse-path Target FEC Stack TLV Section 3.4.2 defines a new TLV type for inclusion in the LSP-Ping packet. IANA is requested to assign a type value to the TLV from the Gray, et al. Expires March 30, 2012 [Page 17] Internet-Draft MPLS On-demand Connectivity Verification September 2011 "Multiprotocol Label Switching Architecture (MPLS) Label Switched Paths (LSPs) Ping Parameters - TLVs" registry, "TLVs and sub-TLVs" sub-registry. Value Meaning Reference ----- -------------------------- ------------------------ TBD-1 Reverse-path Target FEC this document (sect 3.4) Stack TLV The sub-TLV space and assignments for this TLV will be the same as that for the Target FEC Stack TLV. Sub-types for the Target FEC Stack TLV and the Reverse-path Target FEC Stack TLV MUST be kept the same. Any new sub-type added to the Target FEC Stack TLV MUST apply to the Reverse-path Target FEC Stack TLV as well. 7.4. New Pseudowire Associated Channel Type On-demand Connectivity Verification requires a unique Associated Channel Type. IANA is requested to assign a PW ACh Type from the "Pseudowire Associated Channel Types Registry" as describe below: Value Description TLV Follows Reference ------ ------------- ----------- ---------------------- TBD-2 On-Demand CV No this document (sect 3) ACH TLVs SHALL NOT be associated with this channel type. 7.5. New RFC 4379 Registry [RFC4379] defined several registries. It also defined some value assignments without explicitly asking for IANA to create a registry to support additional value assingments. One such case is in defining address types associated with the Downstream Mapping (DSMAP) TLV. This document extends RFC 4379 by defining a new address type for use with the Downstream Mapping and Downstream Detailed Mapping TLVs. Recognizing that the absence of a registry makes it possible to have collisions of "address-type" usages, IANA is requested to establish a new registry - associated with both [RFC4379] and this document - that initially allocates the following assignments: Gray, et al. Expires March 30, 2012 [Page 18] Internet-Draft MPLS On-demand Connectivity Verification September 2011 Type # Address Type K Octets Reference ------ ------------ -------- -------------------------- 1 IPv4 Numbered 16 RFC 4379 2 IPv4 Unnumbered 16 RFC 4379 3 IPv6 Numbered 40 RFC 4379 4 IPv6 Unnumbered 28 RFC 4379 5 Non IP 12 this document (sect 2.1.1) Downstream Mapping Address Type Registry Because the field in this case is an 8-bit field, the allocation policy for this registry is "Standards Action." 8. Contributing Authors and Acknowledgements The following individuals contributed materially to this document: o Thomas D. Nadeau, CA Technologies o Nurit Sprecher, Nokia Siemens Networks o Yaacov Weingarten, Nokia Siemens Networks In addition, we would like to thank the following individuals for their efforts in reviewing and commenting on the document: o Adrian Farrel, o Alexander Vaishtein, o David Sinicrope (Routing Directorate), o Greg Mirsky, o Hideki Endo, o Huub van Helvoort, o Joel Halpern (Routing Directorate), o Loa Andersson, o Mach Chen, o Mahesh Akula, o Sam Aldrin, o Sandra Murphy (Security Directorate), o Yaacov Weingarten, o Yoshinori Koike, o Zhenlong Cui 9. References 9.1. Normative References [I-D.ietf-mpls-lsp-ping-enhanced-dsmap] Bahadur, N., Kompella, K., and G. Swallow, "Mechanism for Gray, et al. Expires March 30, 2012 [Page 19] Internet-Draft MPLS On-demand Connectivity Verification September 2011 performing LSP-Ping over MPLS tunnels", draft-ietf-mpls-lsp-ping-enhanced-dsmap-11 (work in progress), September 2011. [I-D.ietf-mpls-p2mp-lsp-ping] Saxena, S., Swallow, G., Ali, Z., Farrel, A., Yasukawa, S., and T. Nadeau, "Detecting Data Plane Failures in Point-to-Multipoint Multiprotocol Label Switching (MPLS) - Extensions to LSP Ping", draft-ietf-mpls-p2mp-lsp-ping-18 (work in progress), September 2011. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC4379] Kompella, K. and G. Swallow, "Detecting Multi-Protocol Label Switched (MPLS) Data Plane Failures", RFC 4379, February 2006. [RFC4385] Bryant, S., Swallow, G., Martini, L., and D. McPherson, "Pseudowire Emulation Edge-to-Edge (PWE3) Control Word for Use over an MPLS PSN", RFC 4385, February 2006. [RFC5586] Bocci, M., Vigoureux, M., and S. Bryant, "MPLS Generic Associated Channel", RFC 5586, June 2009. [RFC6370] Bocci, M., Swallow, G., and E. Gray, "MPLS Transport Profile (MPLS-TP) Identifiers", RFC 6370, September 2011. 9.2. Informative References [RFC1122] Braden, R., "Requirements for Internet Hosts - Communication Layers", STD 3, RFC 1122, October 1989. [RFC1812] Baker, F., "Requirements for IP Version 4 Routers", RFC 1812, June 1995. [RFC4446] Martini, L., "IANA Allocations for Pseudowire Edge to Edge Emulation (PWE3)", BCP 116, RFC 4446, April 2006. [RFC5003] Metz, C., Martini, L., Balus, F., and J. Sugimoto, "Attachment Individual Identifier (AII) Types for Aggregation", RFC 5003, September 2007. [RFC5860] Vigoureux, M., Ward, D., and M. Betts, "Requirements for Operations, Administration, and Maintenance (OAM) in MPLS Transport Networks", RFC 5860, May 2010. [RFC5884] Aggarwal, R., Kompella, K., Nadeau, T., and G. Swallow, Gray, et al. Expires March 30, 2012 [Page 20] Internet-Draft MPLS On-demand Connectivity Verification September 2011 "Bidirectional Forwarding Detection (BFD) for MPLS Label Switched Paths (LSPs)", RFC 5884, June 2010. [RFC6371] Busi, I. and D. Allan, "Operations, Administration, and Maintenance Framework for MPLS-Based Transport Networks", RFC 6371, September 2011. Authors' Addresses Eric Gray Ericsson 900 Chelmsford Street Lowell, MA 01851 US Phone: +1 978 275 7470 Fax: Email: eric.gray@ericsson.com URI: Nitin Bahadur Juniper Networks, Inc. 1194 N. Mathilda Avenue Sunnyvale, CA 94089 US Phone: +1 408 745 2000 Email: nitinb@juniper.net URI: www.juniper.net Sami Boutros Cisco Systems, Inc. 3750 Cisco Way San Jose, CA 95134 US Phone: Fax: Email: sboutros@cisco.com URI: Gray, et al. Expires March 30, 2012 [Page 21] Internet-Draft MPLS On-demand Connectivity Verification September 2011 Rahul Aggarwal Email: raggarwa_1@yahoo.com Gray, et al. Expires March 30, 2012 [Page 22]