Internet Engineering Task Force Tim Jenkins IP Security Working Group Catena Networks Internet Draft John Shriver Intel Corporation February 7, 2001 ISAKMP DOI-Independent Monitoring MIB Status of this Memo This document is a submission to the IETF Internet Protocol Security (IPsec) Working Group. Comments are solicited and should be addressed to the working group mailing list (ipsec@lists.tislabs.com) or to the editor. This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC 2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or made obsolete by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at . The list of Internet-Draft Shadow Directories can be accessed at . Copyright Notice This document is a product of the IETF's IPsec Working Group. Copyright (C) The Internet Society (2001). All Rights Reserved. Jenkins & Shriver Expires August 7, 2001 [Page 1] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 Table of Contents 1. The SNMP Management Framework...................................2 1.1 Object Definitions.............................................3 2. ISAKMP DOI-independent MIB Objects Architecture.................4 2.1 Phase 1 Security Associations Table............................4 3. MIB Definitions.................................................4 4. Security Considerations........................................23 5. Acknowledgments................................................24 6. References.....................................................25 Introduction This document defines a DOI (domain of interpretation) independent monitoring MIB for ISAKMP. The purpose of this MIB is to be used as the basis for protocol specific MIBs that use ISAKMP as the basis for key exchanges or security association negotiation. As such, it has no DOI-dependent objects. 1. The SNMP Management Framework The SNMP Management Framework presently consists of five major components: o An overall architecture, described in RFC 2571 [RFC2571]. o Mechanisms for describing and naming objects and events for the purpose of management. The first version of this Structure of Management Information (SMI) is called SMIv1 and described in STD 16, RFC 1155 [RFC1155], STD 16, RFC 1212 [RFC1212] and RFC 1215 [RFC1215]. The second version, called SMIv2, is described in STD 58, RFC 2578 [RFC2578], RFC 2579 [RFC2579] and RFC 2580 [RFC2580]. o Message protocols for transferring management information. The first version of the SNMP message protocol is called SNMPv1 and described in STD 15, RFC 1157 [RFC1157]. A second version of the SNMP message protocol, which is not an Internet standards track protocol, is called SNMPv2c and described in RFC 1901 [RFC1901] and RFC 1906 [RFC1906]. The third version of the message protocol is called SNMPv3 and described in RFC 1906 [RFC1906], RFC 2572 [RFC2572] and RFC 2574 [RFC2574]. Jenkins & Shriver [Page 2] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 o Protocol operations for accessing management information. The first set of protocol operations and associated PDU formats is described in STD 15, RFC 1157 [RFC1157]. A second set of protocol operations and associated PDU formats is described in RFC 1905 [RFC1905]. o A set of fundamental applications described in RFC 2573 [RFC2573] and the view-based access control mechanism described in RFC 2575 [RFC2575]. A more detailed introduction to the current SNMP Management Framework can be found in RFC 2570 [RFC2570]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the mechanisms defined in the SMI. This memo specifies a MIB module that is compliant to the SMIv2. A MIB conforming to the SMIv1 can be produced through the appropriate translations. The resulting translated MIB must be semantically equivalent, except where objects or events are omitted because no translation is possible (use of Counter64). Some machine readable information in SMIv2 will be converted into textual descriptions in SMIv1 during the translation process. However, this loss of machine readable information is not considered to change the semantics of the MIB. 1.1 Object Definitions Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the subset of Abstract Syntax Notation One (ASN.1) defined in the SMI. In particular, each object type is named by an OBJECT IDENTIFIER, an administratively assigned name. The object type together with an object instance serves to uniquely identify a specific instantiation of the object. For human convenience, we often use a textual string, termed the descriptor, to refer to the object type. Jenkins & Shriver [Page 3] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 2. ISAKMP DOI-independent MIB Objects Architecture The ISAKMP DOI-independent MIB consists of consists of a table of security associations (SAs), providing the DOI-independent portion of all SAs that use ISAKMP as the basis of their negotiations. There are also provided entity statistics related to generic ISAKMP SA usage. The traffic statistics collected include re-transmissions and both encrypted and unencrypted traffic to allow network administrators determine how much of their total traffic is related to ISAKMP, and thus management of security associations in general. There is a single trap defined. The reason for this is that the DOI- independent portion of ISAKMP makes no assumptions about the use of ISAKMP, aside from the aggregate statistics assumption stated above. The single trap defined is the invalid cookie trap; it is provided since repeated detection of this error can indicate systems that have become badly out of sync or are subject to denial-of-service attacks. There is no count of notifications sent or received. The reason for this is that the usage of notifications is associated with specific DOIs (even though there are ISAKMP defined notification types), and this is a DOI-independent MIB. Protocols that use the notifications must be designed to allow counting of the notification types from DOI of 0 if they use the ISAKMP notification types in addition to their own. 2.1 Phase 1 Security Associations Table This table includes the uniqueness identifiers for those SAs, some version information, some communications information and some basic status information. Also included are aggregate statistics based on the assumption that DOI-specific usage of ISAKMP is for the purpose of negotiating SAs. Additional tables could be generated that are specific to the ISAKMP DOI, however, there is no attempt to define these tables as part of this MIB. These tables are intended to be part of a separate MIB. 3. MIB Definitions ISAKMP-DOI-IND-MON-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Gauge32, Jenkins & Shriver [Page 4] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 Counter64, NOTIFICATION-TYPE, OBJECT-IDENTITY -- delete this and next line before release , experimental FROM SNMPv2-SMI TEXTUAL-CONVENTION, TruthValue FROM SNMPv2-TC OBJECT-GROUP, NOTIFICATION-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF InetAddressType, InetAddress FROM INET-ADDRESS-MIB IsakmpDOI, IsakmpExchangeType FROM IPSEC-ISAKMP-IKE-DOI-TC; isakmpDoiIndMonModule MODULE-IDENTITY LAST-UPDATED "0102071200Z" ORGANIZATION "IETF IPsec Working Group" CONTACT-INFO " Tim Jenkins Catena Networks 307 Legget Drive Kanata, ON Canada K2K 3C8 +1 (613) 599-6430 tjenkins@catena.com John Shriver Intel Corporation 28 Crosby Drive Bedford, MA 01730 +1 (781) 687-1329 John.Shriver@intel.com " DESCRIPTION "The MIB module to describe the DOI-independent part of ISAKMP objects; to be used for monitoring purposes." REVISION "9906031200Z" DESCRIPTION "Initial revision." REVISION "9910211200Z" DESCRIPTION "Compliances and groups added. OID value under experimental tree added. Removed SA expiration objects. Added invalid cookie count and trap." REVISION "0007101200Z" Jenkins & Shriver [Page 5] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 DESCRIPTION "Change addresses to use format from INET-ADDRESS-MIB. Add explicit trap objects. Other minor changes." REVISION "0102071200Z" DESCRIPTION "Change MAX-ACCESS clause of index objects to not-accessible. This lead to other changes due to restrictions on the use of objects with MAX-ACCESS clause values of not-accessible." -- replace xxx in next line before release, uncomment before release -- ::= { mib-2 xxx } -- delete this and next line before release ::= { experimental 99 } isakmpDoiIndMIBObjects OBJECT-IDENTITY STATUS current DESCRIPTION "This is the base object identifier for all ISAKMP branches." ::= { isakmpDoiIndMonModule 1 } -- -- significant branches -- isakmpSaTable OBJECT-IDENTITY STATUS current DESCRIPTION "This is the base object identifier for the security associations table." ::= { isakmpDoiIndMIBObjects 1 } isakmpGlobals OBJECT-IDENTITY STATUS current DESCRIPTION "This is the base object identifier for all objects which are global values for ISAKMP." ::= { isakmpDoiIndMIBObjects 2 } isakmpNegStats OBJECT-IDENTITY STATUS current DESCRIPTION "This is the base object identifier for all objects which are global counters for ISAKMP negotiation statistics." ::= { isakmpDoiIndMIBObjects 3 } Jenkins & Shriver [Page 6] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 isakmpTrafStats OBJECT-IDENTITY STATUS current DESCRIPTION "This is the base object identifier for all objects which are global counters for ISAKMP security association traffic statistics." ::= { isakmpDoiIndMIBObjects 4 } isakmpErrors OBJECT-IDENTITY STATUS current DESCRIPTION "This is the base object identifier for all objects which are global error counters for ISAKMP." ::= { isakmpDoiIndMIBObjects 5 } isakmpGroups OBJECT-IDENTITY STATUS current DESCRIPTION "This is the base object identifier for all objects which describe the groups in this MIB." ::= { isakmpDoiIndMIBObjects 6 } isakmpConformance OBJECT-IDENTITY STATUS current DESCRIPTION "This is the base object identifier for all objects which describe the conformance for this MIB." ::= { isakmpDoiIndMIBObjects 7 } isakmpTrapControl OBJECT-IDENTITY STATUS current DESCRIPTION "This is the base object identifier for all trap controls for this MIB." ::= { isakmpDoiIndMIBObjects 8 } isakmpTraps OBJECT-IDENTITY STATUS current DESCRIPTION "This is the base object identifier for all traps for this MIB." ::= { isakmpDoiIndMIBObjects 9 } isakmpTrapObjects OBJECT-IDENTITY STATUS current Jenkins & Shriver [Page 7] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 DESCRIPTION "This is the base object identifier for all objects used by traps for this MIB." ::= { isakmpDoiIndMIBObjects 10 } -- -- textual conventions -- IsakmpCookie ::= TEXTUAL-CONVENTION DISPLAY-HINT "x" STATUS current DESCRIPTION "This data type is used to model ISAKMP cookies. This is a binary string of 8 octets in network byte-order." SYNTAX OCTET STRING (SIZE (8)) -- the ISAKMP DOI-independent SA MIB-Group -- -- a collection of objects providing information about the -- DOI-independent portion of SAs generated using ISAKMP -- saTable OBJECT-TYPE SYNTAX SEQUENCE OF SaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing the DOI-independent portion of ISAKMP SAs. There should be one row for every phase 1 security association that exists in the entity that uses ISAKMP. The maximum number of rows is implementation dependent." ::= { isakmpSaTable 1 } saEntry OBJECT-TYPE SYNTAX SaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) containing the DOI-independent information on a particular ISAKMP SA. A row in this table cannot be created or deleted by SNMP operations on columns of the table." INDEX { saLocalIpAddressType, Jenkins & Shriver [Page 8] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 saLocalIpAddress, saRemoteIpAddressType, saRemoteIpAddress, saInitiatorCookie, saResponderCookie } ::= { saTable 1 } SaEntry::= SEQUENCE { -- identification saLocalIpAddressType InetAddressType, saLocalIpAddress InetAddress, saRemoteIpAddressType InetAddressType, saRemoteIpAddress InetAddress, saInitiatorCookie IsakmpCookie, saResponderCookie IsakmpCookie, -- communication information saLocalUdpPort INTEGER, saRemoteUdpPort INTEGER, -- peer version information saPeerMajorVersion INTEGER, saPeerMinorVersion INTEGER, -- creation/status/type saDoi IsakmpDOI, saLocallyInitiated TruthValue, saStatus INTEGER, saExchangeType IsakmpExchangeType, -- statistics saTimeSeconds Counter32, saInPackets Counter32, saOutPackets Counter32, saInOctets Counter32, saOutOctets Counter32 } saLocalIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of the local address used to negotiate the ISAKMP phase 1 SA." ::= { saEntry 1 } Jenkins & Shriver [Page 9] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 saLocalIpAddress OBJECT-TYPE SYNTAX InetAddress (SIZE(4|16|20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The local address used to negotiate the ISAKMP phase 1 SA." ::= { saEntry 2 } saRemoteIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of the remote address used to negotiate the ISAKMP phase 1 SA." ::= { saEntry 3 } saRemoteIpAddress OBJECT-TYPE SYNTAX InetAddress (SIZE(4|16|20)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The remote address used to negotiate the ISAKMP phase 1 SA." ::= { saEntry 4 } saInitiatorCookie OBJECT-TYPE SYNTAX IsakmpCookie MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of the cookie used by the initiator for the ISAKMP phase 1 SA." ::= { saEntry 5 } saResponderCookie OBJECT-TYPE SYNTAX IsakmpCookie MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of the cookie used by the responder for the ISAKMP phase 1 SA. Note that this value may be 0 if the ISAKMP phase 1 SA has been initiated but not responded to by the peer entity. Jenkins & Shriver [Page 10] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 It must never be 0 if this entry represents an ISAKMP phase 1 SA establishment attempt that has been initiated by the peer. This rule prevents index collisions in the (unlikely) event that two peers simultaneously initiate with the same cookie at the same time." ::= { saEntry 6 } saLocalUdpPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The local UDP port number that this ISAKMP phase 1 SA was negotiated with." ::= { saEntry 7 } saRemoteUdpPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The remote UDP port number that this ISAKMP phase 1 SA was negotiated with." ::= { saEntry 8 } saPeerMajorVersion OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The major version number from the ISAKMP packet header used by the peer." REFERENCE "Section 3.1 of RFC 2408" ::= { saEntry 9 } saPeerMinorVersion OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The minor version number from the ISAKMP packet header used by the peer." REFERENCE "Section 3.1 of RFC 2408" ::= { saEntry 10 } saDoi OBJECT-TYPE SYNTAX IsakmpDOI MAX-ACCESS read-only Jenkins & Shriver [Page 11] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 STATUS current DESCRIPTION "The specific DOI value that this ISAKMP SA is using. Note that this value MAY be 0, as allowed by Section 3.4 of RFC 2408" REFERENCE "Section 3.3 of RFC 2408" ::= { saEntry 11 } saLocallyInitiated OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This value is 'true' if the ISAKMP phase 1 SA was initiated by the local entity, and 'false' if initiated by the remote entity." ::= { saEntry 12 } saStatus OBJECT-TYPE SYNTAX INTEGER { negotiating(1), established(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the ISAKMP phase 1 SA. If the state is 'negotiating', it means that processing of the final packet of the phase 1 exchange is not yet complete. If the state is 'established', it means that processing of all packets associated with ISAKMP phase 1 SA negotation is complete, and the entities involved in the ISAKMP phase 1 SA are authenticated." ::= { saEntry 13 } saExchangeType OBJECT-TYPE SYNTAX IsakmpExchangeType MAX-ACCESS read-only STATUS current DESCRIPTION "The exchange type used to negotiate the ISAKMP phase 1 SA." REFERENCE "Section 3.1 of RFC 2408" ::= { saEntry 14 } saTimeSeconds OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" Jenkins & Shriver [Page 12] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds the SA has existed. In other words, how old the SA is." ::= { saEntry 15 } saInPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by the ISAKMP phase 1 SA, including un-encrypted packets used to negotiate the ISAKMP phase 1 SA, and any re-transmissions." ::= { saEntry 16 } saOutPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets sent by the ISAKMP phase 1 SA, including un-encrypted packets used to negotiate the ISAKMP phase 1 SA, and any re-transmissions received." ::= { saEntry 17 } saInOctets OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of traffic measured in bytes received by the ISAKMP phase 1 SA. This includes encrypted and un-encrypted traffic used to negotiate the ISAKMP phase 1 SA, and any re- transmissions received." ::= { saEntry 18 } saOutOctets OBJECT-TYPE SYNTAX Counter32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of traffic measured in bytes sent by the ISAKMP phase 1 SA. This includes encrypted and un-encrypted traffic Jenkins & Shriver [Page 13] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 used to negotiate the ISAKMP phase 1 SA, and any re- transmissions." ::= { saEntry 19 } -- -- the ISAKMP Entity MIB-Group -- isakmpMajorVersion OBJECT-TYPE SYNTAX INTEGER ( 0..15 ) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum major version number value capable of being supported by the entity." ::= { isakmpGlobals 1 } isakmpMinorVersion OBJECT-TYPE SYNTAX INTEGER ( 0..15 ) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum minor version number value capable of being supported by the entity." ::= { isakmpGlobals 2 } -- -- ISAKMP phase 1 SA statistics -- isakmpCurrentSAs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of ISAKMP SAs in the entity." ::= { isakmpNegStats 1 } isakmpCurrentInitiatedSAs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of ISAKMP SAs successfully negotiated in the entity that were initiated by the entity." ::= { isakmpNegStats 2 } Jenkins & Shriver [Page 14] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 isakmpCurrentRespondedSAs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of ISAKMP SAs successfully negotiated in the entity that were initiated by the peer entity." ::= { isakmpNegStats 3 } isakmpTotalSAs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ISAKMP SAs successfully negotiated in the entity since boot time." ::= { isakmpNegStats 4 } isakmpTotalInitiatedSAs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ISAKMP SAs successfully negotiated in the entity since boot time that were initiated by the entity." ::= { isakmpNegStats 5 } isakmpTotalRespondedSAs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ISAKMP SAs successfully negotiated in the entity since boot time that were initiated by the peer entity." ::= { isakmpNegStats 6 } isakmpTotalAttempts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ISAKMP SAs negotiation attempts made since boot time. This includes successful negotiations." ::= { isakmpNegStats 7 } Jenkins & Shriver [Page 15] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 isakmpTotalAsInitAttempts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ISAKMP SAs negotiation attempts made where the entity was the initiator since boot time. This includes successful negotiations." ::= { isakmpNegStats 8 } isakmpTotalAsRespAttempts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ISAKMP SAs negotiation attempts made where the entity was the responder since boot time. This includes successful negotiations." ::= { isakmpNegStats 9 } -- -- traffic statistics -- isakmpTotalInPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ISAKMP packets received by the entity since boot time, including re-transmissions and un-encrypted packets." ::= { isakmpTrafStats 1 } isakmpTotalOutPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ISAKMP packets sent by the entity since boot time, including re-transmissions and un-encrypted packets." ::= { isakmpTrafStats 2 } isakmpTotalInOctets OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" Jenkins & Shriver [Page 16] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 MAX-ACCESS read-only STATUS current DESCRIPTION "The total amount of ISAKMP traffic received by the entity since boot time, measured in bytes, including any re- transmitted packets received, and including encrypted and un-encrypted packets." ::= { isakmpTrafStats 3 } isakmpTotalOutOctets OBJECT-TYPE SYNTAX Counter64 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The total amount of ISAKMP traffic sent by the entity since boot time, measured in bytes, including any re-transmissions and including encrypted and un-encrypted packets." ::= { isakmpTrafStats 4 } -- -- global error counts -- isakmpTotalInitFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of attempts to initiate an ISAKMP phase 1 SA that failed since boot time, when there was a response from the peer entity. This value may be used to detect clogging or denial-of- service attacks." ::= { isakmpErrors 1 } isakmpTotalInitNoResponses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of attempts to initiate an ISAKMP phase 1 SA that failed since boot time, when there was no response from the peer entity. Jenkins & Shriver [Page 17] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 This should only be incremented if the peer does not repond to the first packet of attempted negotiations." ::= { isakmpErrors 2 } isakmpTotalRespFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of attempts to initiate an ISAKMP phase 1 SA that failed since boot time, when the initiation attempt came for the peer entity." ::= { isakmpErrors 3 } isakmpInvalidCookieCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ISAKMP packets with invalid cookies received by the entity since boot time." ::= { isakmpErrors 4 } -- -- ISAKMP Traps and Control -- invalidCookieTrapEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether invalidCookieTrap traps should be generated." DEFVAL { false } ::= { isakmpTrapControl 1 } localIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The type of the local IP address used in an ISAKMP message, to be associated with a trap." ::= { isakmpTrapObjects 1 } Jenkins & Shriver [Page 18] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 localIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The local IP address used in an ISAKMP message, to be associated with a trap." ::= { isakmpTrapObjects 2 } localUdpPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The local port UDP number used in an ISAKMP message, to be associated with a trap." ::= { isakmpTrapObjects 3 } remoteIpAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The type of the remote IP used in an ISAKMP message, to be associated with a trap." ::= { isakmpTrapObjects 4 } remoteIpAddress OBJECT-TYPE SYNTAX IsakmpCookie MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The remote IPaddress used in an ISAKMP message, to be associated with a trap." ::= { isakmpTrapObjects 5 } remoteUdpPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The remote UDP port number used in an ISAKMP message, to be associated with a trap." ::= { isakmpTrapObjects 6 } initiatorCookie OBJECT-TYPE SYNTAX IsakmpCookie Jenkins & Shriver [Page 19] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The initiator cookie used in an ISAKMP message, to be associated with a trap." ::= { isakmpTrapObjects 7 } responderCookie OBJECT-TYPE SYNTAX IsakmpCookie MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The responder cookie used in an ISAKMP message, to be associated with a trap." ::= { isakmpTrapObjects 8 } invalidCookieTrap NOTIFICATION-TYPE OBJECTS { localIpAddressType, localIpAddress, localUdpPort, remoteIpAddressType, remoteIpAddress, remoteUdpPort, initiatorCookie, responderCookie, isakmpInvalidCookieCount } STATUS current DESCRIPTION "ISAKMP packets with invalid cookies were detected from the specified source, intended for the specified destination. The initiator and responder cookies are also sent with the trap. The current count is sent to allow the trap to accurately relfect dropped and throttled traps. Implementations SHOULD send one trap per peer (within a reasonable time period, rather than sending one trap per packet." ::= { isakmpTraps 0 1 } -- -- Units of Conformance (Object Groups) -- Jenkins & Shriver [Page 20] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 isakmpSaGroup OBJECT-GROUP OBJECTS { -- saLocalIpAddressType, saLocalIpAddress, -- saRemoteIpAddressType, saRemoteIpAddress, -- saInitiatorCookie, saResponderCookie, saLocalUdpPort, saRemoteUdpPort, saPeerMajorVersion, saPeerMinorVersion, saDoi, saLocallyInitiated, saStatus, saExchangeType, saTimeSeconds, saInPackets, saOutPackets, saInOctets, saOutOctets } STATUS current DESCRIPTION "A collection of objects that describe the state of the security associations of the ISAKMP protocol." ::= { isakmpGroups 1 } isakmpGlobalsGroup OBJECT-GROUP OBJECTS { isakmpMajorVersion, isakmpMinorVersion, isakmpCurrentSAs, isakmpCurrentInitiatedSAs, isakmpCurrentRespondedSAs, isakmpTotalSAs, isakmpTotalInitiatedSAs, isakmpTotalRespondedSAs, isakmpTotalAttempts, isakmpTotalAsInitAttempts, isakmpTotalAsRespAttempts, isakmpTotalInPackets, isakmpTotalOutPackets, isakmpTotalInOctets, isakmpTotalOutOctets, isakmpTotalInitFailures, isakmpTotalInitNoResponses, isakmpTotalRespFailures, isakmpInvalidCookieCount } STATUS current DESCRIPTION "A collections of objects that describe the global state of the ISAKMP protocol." ::= { isakmpGroups 2 } isakmpTrapControlGroup OBJECT-GROUP OBJECTS { invalidCookieTrapEnable } STATUS current DESCRIPTION "Trap control for the ISAKMP protocol." ::= { isakmpGroups 3 } Jenkins & Shriver [Page 21] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 isakmpTrapDataGroup OBJECT-GROUP OBJECTS { localIpAddressType, localIpAddress, localUdpPort, remoteIpAddressType, remoteIpAddress, remoteUdpPort, initiatorCookie, responderCookie } STATUS current DESCRIPTION "Trap data for the ISAKMP protocol." ::= { isakmpGroups 4 } isakmpTrapGroup NOTIFICATION-GROUP NOTIFICATIONS { invalidCookieTrap } STATUS current DESCRIPTION "The traps for the ISAKMP protocol." ::= { isakmpGroups 5 } -- -- Compliance Statements -- isakmpDoiIndependentMonitorCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the SNMPv3 entities which implement the ISAKMP DOI-Indpendent Monitoring MIB." MODULE -- this module MANDATORY-GROUPS { isakmpSaGroup, isakmpGlobalsGroup, isakmpTrapControlGroup, isakmpTrapDataGroup, isakmpTrapGroup } -- Allows the trap control to be read-only. OBJECT invalidCookieTrapEnable MIN-ACCESS read-only DESCRIPTION "If an implementation cannot properly secure this variable against unauthorized write access, it SHOULD implement it as read-only, to prevent the security risk of enabling the traps. Of course, there must be other means of controlling the generation of the associated trap." Jenkins & Shriver [Page 22] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 -- Don't require support for dns(16) address type -- Authors' note: The following statements are commented out, -- since the current SMI does not allow objects with a -- MAX-ACCESS clause of not-accessible to be put in groups, -- and objects that are not in groups cannot be in -- compliance statements. -- OBJECT saLocalIpAddressType -- SYNTAX INTEGER { ipv4(1), ipv6(2) } -- DESCRIPTION -- "An implementation is only required to support IPv4 and IPv6 -- addresses." -- OBJECT saRemoteIpAddressType -- SYNTAX INTEGER { ipv4(1), ipv6(2) } -- DESCRIPTION -- "An implementation is only required to support IPv4 and IPv6 -- addresses." ::= { isakmpConformance 1 } END 4. Security Considerations This MIB contains readable objects whose values provide information related to IPsec SAs. While some of the information is readily available by monitoring the traffic into an entity, other information may provide attackers with more information than an administrator may desire. Of particular concern is the ability to disable the transmission of traps. The traps defined in this MIB may appear due to badly configured systems and transient error conditions, but they may also appear due to attacks. If an attacker can disable these traps, they reduce some of the warnings that may be provided to system administrators. While unauthorized access to the readable objects is relatively innocuous, unauthorized access to those objects through an insecure channel can provide attackers with more information about a system than an administrator may desire. Jenkins & Shriver [Page 23] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 A specific example of this includes, but is not limited to, the monitoring of global statistic counts by attackers that provides feedback on the progress of an attack. It is thus important to control even GET access to these objects and possibly to even encrypt the values of these object when sending them over the network via SNMP. Not all versions of SNMP provide features for such a secure environment. SNMPv1 by itself is not a secure environment. Even if the network itself is secure (for example by using IPsec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB. It is recommended that the implementers consider the security features as provided by the SNMPv3 framework. Specifically, the use of the User-based Security Model RFC 2574 [RFC2574] and the View- based Access Control Model RFC 2575 [RFC2575] is recommended. It is then a customer/user responsibility to ensure that the SNMP entity giving access to an instance of this MIB, is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 5. Acknowledgments This document is based in part on an earlier proposal titled "draft- ietf-ipsec-mib-xx.txt". That series was abandoned, since it included application specific constructs in addition to the IPsec only objects. Portions of the original document's origins were based on the working paper "IP Security Management Information Base" by R. Thayer and U. Blumenthal. Contribution to the IPsec MIB series of documents comes from D. McDonald, M. Baugher, C. Brooks, C. Powell, M. Daniele, T. Kivinen, J. Walker, S. Kelly, J. Leonard, M. Richardson and R. Charlet, and others participating in the IPsec working group. Jenkins & Shriver [Page 24] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 6. References [ADDRMIB] Daniele, M., Haberman, B., Routhier, S., Schoenwaelder, J., "Textual Conventions for Internet Network Addresses", RFC 2851, June, 2000 [IPSECTC] Shriver, J., "IPSec DOI Textual Conventions MIB ", work in progress, November 22, 2000 [ISAKMP]Maughan, D., Schertler, M., Schneider, M., and Turner, J., "Internet Security Association and Key Management Protocol (ISAKMP)", RFC 2408, November 1998 [RFC2571] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for Describing SNMP Management Frameworks", RFC 2571, April 1999 [RFC1155] Rose, M., and K. McCloghrie, "Structure and Identification of Management Information for TCP/IP-based Internets", STD 16, RFC 1155, May 1990 [RFC1212] Rose, M., and K. McCloghrie, "Concise MIB Definitions", STD 16, RFC 1212, March 1991 [RFC1215] M. Rose, "A Convention for Defining Traps for use with the SNMP", RFC 1215, March 1991 [RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M., and S. Waldbusser, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999 [RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M., and S. Waldbusser, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999 [RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M., and S. Waldbusser, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999 [RFC1157] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network Management Protocol", STD 15, RFC 1157, May 1990. [RFC1901] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Introduction to Community-based SNMPv2", RFC 1901, January 1996. Jenkins & Shriver [Page 25] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 [RFC1906] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1906, January 1996. [RFC2572] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)", RFC 2572, April 1999 [RFC2574] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", RFC 2574, April 1999 [RFC1905] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1905, January 1996. [RFC2573] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC 2573, April 1999 [RFC2575] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", RFC 2575, April 1999 [RFC2570] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction to Version 3 of the Internet-standard Network Management Framework", RFC 2570, April 1999 Authors' Addresses Tim Jenkins tjenkins@catena.com Catena Networks 307 Legget Drive Kanata, ON Canada K2K 3C8 +1 (613) 599-6430 John Shriver John.Shriver@intel.com Intel Corporation 28 Crosby Drive Bedford, MA 01730 +1 (781) 687-1329 Jenkins & Shriver [Page 26] Internet Draft ISAKMP DOI-Independent Monitoring MIB February 7, 2001 The IPsec working group can be contacted via the IPsec working group's mailing list (ipsec@lists.tislabs.com) or through its chair: Theodore Y. Ts'o tytso@MIT.EDU Massachusetts Institute of Technology Expiration This document expires August 7, 2001. Jenkins & Shriver [Page 27]