Network Working Group A. Bierman
Internet-Draft Brocade
Intended status: Standards Track M. Bjorklund
Expires: May 03, 2012 Tail-f Systems
October 31, 2011

YANG Data Model for System Management
draft-bierman-netmod-system-mgmt-01

Abstract

This document defines a YANG data model for the configuration and identification of the management system of a device.

Status of this Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on May 03, 2012.

Copyright Notice

Copyright (c) 2011 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.


Table of Contents

1. Introduction

This document defines a YANG [RFC6020] data model for the configuration and identification of the management system of a device.

Devices that are managed by NETCONF and perhaps other mechanisms have common properties that need to be configured and monitored in a standard way.

The YANG module defined in this document provides the following features:

1.1. Terminology

The keywords "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14, [RFC2119].

1.1.1. Terms

The following terms are used within this document:

2. Objectives

2.1. System Identification

There are many common properties used to identify devices, operating systems, software versions, etc. that need to be supported in the system data module. These objects are defined as operational data and intended to be specific to the device vendor.

Some user-configurable administrative strings are also provided such as the system location and description.

2.2. System Time Management

The management of the date and time used by the system need to be supported. Use of one or more NTP servers to automatically set the system date and time need to be possible. Utilization of the Timezone database [I-D.lear-iana-timezone-database] also need to be supported.

2.3. User Authentication

The authentication mechanism need to support password authentication over RADIUS, to support deployment scenarios with centralized authentication servers. Additionally, local users need to be supported, for scenarios when no centralized authentication server exists, or for situations where the centralized authentication server cannot be reached from the device.

Since the mandatory transport protocol for NETCONF is SSH [RFC6242] the authentication model need to support SSH's "publickey" and "password" authentication methods [RFC4252].

The model for authentication configuration should be flexible enough to support authentication methods defined by other standard documents or by vendors.

3. System Data Model

3.1. System Identification

The data model for system identification has the following structure:

   +--rw system
      +--rw contact?          string
      +--rw name?             string
      +--rw location?         string
      +--ro platform
         +--ro os-name?       string
         +--ro os-release?    string
         +--ro os-version?    string
         +--ro machine?       string
         +--ro nodename?      string
	    

3.2. System Time Management

The data model for system time management has the following structure:

   +--rw system
      +--rw clock
      |  +--ro current-datetime?      yang:date-and-time
      |  +--ro boot-datetime?         yang:date-and-time
      |  +--rw (timezone)?
      |     +--:(timezone-location)
      |     |  +--rw timezone-location?     string
      |     +--:(timezone-name)
      |     |  +--rw timezone-name?         string
      |     +--:(timezone-utc-offset)
      |        +--rw timezone-utc-offset?   int16
      +--rw ntp
         +--rw use-ntp?      boolean
         +--rw ntp-server [address]
            +--rw address    inet:host
	    

3.3. DNS Resolver Model

The data model for configuration of the DNS resolver has the following structure:

   +--rw system
      +--rw dns
         +--rw search*    inet:host
         +--rw server*    inet:ip-address
         +--rw options
            +--rw ndots?      uint8
            +--rw timeout?    uint8
            +--rw attempts?   uint8
	    

3.4. User Authentication Model

This document defines three authentication methods for use with NETCONF:

Additional methods can be defined by other standard documents or by vendors.

This document defines two optional YANG features, "local‑users" and "radius", which the server advertises to indicate support for configuring local users on the device, and for configuring RADIUS access, respectively.

The authentication parameters defined in this document are primarily used to configure authentication of NETCONF users, but MAY also be used by other interfaces, e.g., a Command Line Interface or a Web-based User Interface.

The data model for user authentication has the following structure:

   +--rw system
      +--rw authentication
         +--rw user-authentication-order*   identityref
         +--rw radius
         |  +--rw server [address]
         |  |  +--rw address          inet:host
         |  |  +--rw port?            inet:port-number
         |  |  +--rw shared-secret?   string
         |  +--rw options
         |     +--rw timeout?    uint8
         |     +--rw attempts?   uint8
         +--rw user [name]
            +--rw name        string
            +--rw password?   crypt-hash
            +--rw ssh-dsa?    binary
            +--rw ssh-rsa?    binary
	    

3.4.1. SSH Public Key Authentication

If the NETCONF server advertises the "local‑users" feature, configuration of local users and their SSH public keys is supported in the /system/authentication/user list.

Public key authentication is requested by the SSH client. If the "local‑users" feature is supported, then when a NETCONF client starts an SSH session towards the server using the "publickey" authentication "method name" [RFC4252], the SSH server looks up the user name given in the SSH authentication request in the /system/authentication/user list, and verifies the key as described in [RFC4253].

3.4.2. Local User Password Authentication

If the NETCONF server advertises the "local‑users" feature, configuration of local users and their passwords is supported in the /system/authentication/user list.

For NETCONF transport protocols that support password authentication, the leaf-list "user‑authentication‑order" is used to control if local user password authentication should be used.

In SSH, password authentication is requested by the client. Other NETCONF transport protocols MAY also support password authentication.

When local user password authentication is requested, the NETCONF transport looks up the user name provided by the client in the /system/ authentication/user list, and verifies the password.

3.4.3. RADIUS Password Authentication

If the NETCONF server advertises the "radius" feature, the device supports user authentication RADIUS.

For NETCONF transport protocols that support password authentication, the leaf-list "user‑authentication‑order" is used to control if RADIUS password authentication should be used.

In SSH, password authentication is requested by the client. Other NETCONF transport protocols MAY also support password authentication.

3.5. System Control

Two protocol operations are included to restart or shutdown the system. The 'system‑restart' operation can be used to restart the entire system (not just the NETCONF server). The 'system‑shutdown' operation can be used to power off the entire system.

4. System YANG module

RFC Ed.: update the date below with the date of RFC publication and remove this note.

This YANG module imports YANG extensions from [I-D.ietf-netconf-access-control], imports YANG types from [RFC6021], and references [RFC1321], [RFC2865], [RFC3418], [RFC5607], [IEEE-1003.1-2008], and [FIPS.180-3.2008].

<CODE BEGINS> file "ietf-system@2011-10-30.yang"

module ietf-system {
  namespace "urn:ietf:params:xml:ns:yang:ietf-system";
  prefix "sys";

  import ietf-yang-types {
    prefix yang;
  }

  import ietf-inet-types {
    prefix inet;
  }

  import ietf-netconf-acm {
    prefix nacm;
  }

  organization
    "IETF NETMOD (NETCONF Data Modeling Language) Working Group";

  contact
    "WG Web:   <http://tools.ietf.org/wg/netmod/>
     WG List:  <mailto:netmod@ietf.org>

     WG Chair: David Kessens
               <mailto:david.kessens@nsn.com>

     WG Chair: Juergen Schoenwaelder
               <mailto:j.schoenwaelder@jacobs-university.de>

     Editor:   Andy Bierman
               <mailto:andy.bierman@brocade.com>

     Editor:   Martin Bjorklund
               <mailto:mbj@tail-f.com>";

  description
    "This module contains a collection of YANG definitions for the
     configuration and identification of the management system of a
     device.

     Copyright (c) 2011 IETF Trust and the persons identified as
     authors of the code.  All rights reserved.

     Redistribution and use in source and binary forms, with or
     without modification, is permitted pursuant to, and subject
     to the license terms contained in, the Simplified BSD License
     set forth in Section 4.c of the IETF Trust's Legal Provisions
     Relating to IETF Documents
     (http://trustee.ietf.org/license-info).

     This version of this YANG module is part of RFC XXXX; see
     the RFC itself for full legal notices.";

  // RFC Ed.: replace XXXX with actual RFC number and remove this
  // note.

  // RFC Ed.: remove this note
  // Note: extracted from draft-bierman-netmod-system-mgmt-01.txt

  // RFC Ed.: update the date below with the date of RFC publication
  // and remove this note.
  revision 2011-10-30 {
    description
      "Initial revision.";
    reference
      "RFC XXXX: A YANG Data Model for System Management";
  }
  
  /*
   * Typedefs
   */ 

   typedef crypt-hash {
     type string {
       pattern "$0$.* | $1|5|6$[a-zA-Z0-9./]{2,16}$.*";
     }
     description
       "The crypt-hash type is used to store passwords using
        a hash function.  This type is implemented in various UNIX
        systems as the function crypt(3).

        When a clear text value is set to a leaf of this type, the
        server calculates a password hash, and stores the result
        in the datastore.  Thus, the password is never stored in
        clear text.

        When a leaf of this type is read, the stored password hash is
        returned.

        A value of this type matches one of the forms:

          $0$<clear text password>
          $<id>$<salt>$<password hash>

       The '$0$' prefix signals that the value is clear text.  When
       such a value is received by the server, a hash value is
       calculated, and the string '$<id>$<salt>$' is prepended to the
       result, where <salt> is a random 2-16 characters long salt
       used to generate the digest.  This value is stored in the
       configuration data store.

       If a value starting with '$<id>$<salt>$' is received, the
       server knows that the value already represents a hashed value,
       and stores it as is in the data store.

       When a server needs to verify a password given by a user, it
       finds the stored password hash string for that user, extracts
       the salt, and calculates the hash with the salt and given
       password as input.  If the calculated hash value is the same
       as the stored value, the password given by the client is
       correct.

       This type defines the following hash functions:

         id | hash function | feature
         ---+---------------+-------------------
          1 | MD5           | crypt-hash-md5
          5 | SHA-256       | crypt-hash-sha-256
          6 | SHA-512       | crypt-hash-sha-512

       The server indicates support for the different hash functions
       by advertising the corresponding feature.";
     reference
       "IEEE Std 1003.1-2008 - crypt() function
        Wikipedia: http://en.wikipedia.org/wiki/Crypt_(Unix)
        RFC 1321: The MD5 Message-Digest Algorithm
        FIPS.180-3.2008: Secure Hash Standard";
   }

  /*
   * Features
   */

  feature authentication {
    description
      "Indicates that the device can be configured
       to do authentication of users.";
  }

  feature radius {
    if-feature authentication;
    description
      "Indicates that the device can be
       configured to act as a NAS and authenticate users
       with RADIUS.";
    reference
      "RFC 2865: Remote Authentication Dial In User Service (RADIUS)
       RFC 5607: Remote Authentication Dial-In User Service (RADIUS)
                 Authorization for Network Access Server (NAS)
                 Management";
  }

  feature local-users {
    if-feature authentication;
    description
      "Indicates that the device supports
       local user authentication.";
  }

  feature crypt-hash-md5 {
    description
      "Indicates that the device supports the MD5
       hash function in 'crypt-hash' values";
    reference "RFC 1321: The MD5 Message-Digest Algorithm";
  }

  feature crypt-hash-sha-256 {
    description
      "Indicates that the device supports the SHA-256
       hash function in 'crypt-hash' values";
    reference "FIPS.180-3.2008: Secure Hash Standard";
  }

  feature crypt-hash-sha-512 {
    description
      "Indicates that the device supports the SHA-512
       hash function in 'crypt-hash' values";
    reference "FIPS.180-3.2008: Secure Hash Standard";
  }

  feature ntp {
    description
      "Indicates that the device can be configured
       to use one or more NTP servers to set the 
       system date and time.";
  }

  feature timezone-location {
    description
      "Indicates that the local timezone on the device
       can be configured to use the TZ database
       to set the timezone and manage daylight savings time.";
    reference
      "TZ Database  http://www.twinsun.com/tz/tz-link.htm
       Maintaining the Timezone Database
       http://www.ietf.org/id/draft-lear-iana-timezone-database-04.txt
      ";
  }

  feature timezone-name {
    description
      "Indicates that the local timezone on the device
       can be configured using the timezone enumeration
       strings as an alias for an UTC offset.";
    reference
      "Wikipedia: http://en.wikipedia.org/wiki/"
    + "List_of_time_zone_abbreviations";
  }

  /*
   * Identities
   */
  
  identity authentication-method {
    description
      "Base identity for user authentication methods.";
  }
  
  identity radius {
    base authentication-method;
    description
      "Indicates user authentication using RADIUS.";
    reference
      "RFC 2865: Remote Authentication Dial In User Service (RADIUS)
       RFC 5607: Remote Authentication Dial-In User Service (RADIUS)
                 Authorization for Network Access Server (NAS)
                 Management";
  }

  identity local-users {
    base authentication-method;
    description
      "Indicates password-based authentication of locally
       configured users.";
  }


  /*
   * Top-level container
   */

  container system {
    description
      "System group configuration.";
    
    leaf contact { 
      type string {
        length "0..255";
      }
      default "";
      reference
        "RFC 3418 - Management Information Base (MIB) for the
                    Simple Network Management Protocol (SNMP)
                    SNMPv2-MIB.sysContact";
    }
    
    leaf name {
      type string {
        length "0..255";
      }
      default "";
      reference
        "RFC 3418 - Management Information Base (MIB) for the
                    Simple Network Management Protocol (SNMP)
                    SNMPv2-MIB.sysName";
    }
    
    leaf location {
      type string {
        length "0..255";
      }
      default "";
      reference
        "RFC 3418 - Management Information Base (MIB) for the
                    Simple Network Management Protocol (SNMP)
                    SNMPv2-MIB.sysLocation";
    }

    container platform {
      description
        "Contains vendor-specific information for
         identifying the system platform and operating system.";
      reference
        "IEEE Std 1003.1-2008 - sys/utsname.h";

      config false;

      leaf os-name {
        type string;
        description
          "The name of the operating system in use,
           for example 'Linux'";
        reference
          "IEEE Std 1003.1-2008 - utsname.sysname";
      }

      leaf os-release {
        type string;
        description
          "The current release level of the operating
           system in use.  This string MAY indicate
           the OS source code revision.";
        reference
          "IEEE Std 1003.1-2008 - utsname.release";
      }

      leaf os-version {
        type string;
        description
          "The current version level of the operating
           system in use.  This string MAY indicate
           the specific OS build date and target variant
           information.";
        reference
          "IEEE Std 1003.1-2008 - utsname.version";
      }

      leaf machine {
        type string;
        description 
          "A vendor-specific identifier string representing
           the hardware in use.";
        reference
          "IEEE Std 1003.1-2008 - utsname.machine";
      }

      leaf nodename {
        type string;
        description
          "The host name of this system.";
        reference
          "IEEE Std 1003.1-2008 - utsname.nodename";
      }
    }

    container clock {
      description
        "Configuration and monitoring of the system
         date and time properties.";

      leaf current-datetime {
        description 
          "The current system date and time.";
        type yang:date-and-time;
        config false;
      }

      leaf boot-datetime {
        description
          "The system date and time when the NETCONF
           server last restarted.";
        type yang:date-and-time;
        config false;
      }

      choice timezone {
        description
          "Configure the system timezone information.";

        leaf timezone-location {
          if-feature timezone-location;
          description
            "The TZ database location identifier string
             to use for the system, such as 'Europe/Stockholm'.";
          type string;
        }

        leaf timezone-name {
          if-feature timezone-name;
          description
            "The timezone enumeration string to use
             for the system, such as 'CET'.";
          type string; 
          // FIXME: use TimezoneEnum typedef instead
          // see http://en.wikipedia.org/wiki/
          //           List_of_time_zone_abbreviations
        }

        leaf timezone-utc-offset {
          description
            "The number of minutes to add to UTC time to
             identify the timezone for this system.
             For example, 'UTC - 8:00 hours' would be
             represented as '-480'.";
          type int16 {
            range "-1439 .. 1439";
          }
        }
      }
    }

    container ntp {
      if-feature ntp;

      description
        "Configuration of the NTP client.
         FIXME: should NTP server mode be supported here,
         or in a submodule?  Should NTP client and server
         mode be kept together in the same container?";

      leaf use-ntp {
        description
          "Indicates that the system should attempt
           to synchronize the system clock with an
           NTP server from the 'ntp-server' list.";
        type boolean;
        default true;
      }

      list ntp-server {
        description
          "List of NTP servers to use for
           system clock synchronization.  If 'use-ntp'
           is 'true', then the system will attempt to
           contact and utilize the specified NTP servers.";

        key address;

        leaf address {
          description
            "The IP address or domain name of the NTP server.";
          type inet:host;
        }
      }
    }

    container dns {
      description
        "Configuration of the DNS resolver.";

      leaf-list search {
        type inet:host;
        ordered-by user;
      }
      leaf-list server {
        type inet:ip-address;
        ordered-by user;
        description
          "Addresses of the name servers that the resolver should
           query.

           Implementations MAY limit the number of entries in this
           leaf list.";
      }
      container options {
        description
          "Resolver options.  The set of available options has been
           limited to those that are generally available across
           different resolver implementations, and generally useful.";
        leaf ndots {
          type uint8;
          default "1";
        }
        leaf timeout {
          type uint8;
          units "seconds";
          default "5";
        }
        leaf attempts {
          type uint8;
          default "2";
        }
      }
    }

    container authentication {
      nacm:default-deny-write;
      if-feature authentication;

       description
         "The authentication configuration subtree.";

       leaf-list user-authentication-order {
         type identityref {
           base authentication-method;
         }
         must '(. = "sys:radius" and ../radius/server) or'
            + '(. != "sys:radius")' {
           error-message
             "When 'radius' is used, a radius server
              must be configured.";
         }
         ordered-by user;

         description
           "When the device authenticates a user with
            a password, it tries the authentication methods in this
            leaf-list in order.  If authentication with one method
            fails, the next method is used.  If no method succeeds,
            the user is denied access.

            If the 'radius' feature is advertised by the NETCONF
            server, the 'radius' identity can be added to this
            list.

            If the 'local-users' feature is advertised by the
            NETCONF server, the 'local-users' identity can be
            added to this list.";
       }

       container radius {
         if-feature radius;

         description
           "The RADIUS configuration for authentication.";

         list server {
           key address;
           ordered-by user;

           description
             "The RADIUS server configuration used by
              the device.";

           leaf address {
             type inet:host;
             description
               "The address of the RADIUS server.";
           }
           leaf port {
             type inet:port-number;
             default "1812";
             description
              "The port number of the RADIUS server.";
           }
           leaf shared-secret {
             type string;
             nacm:default-deny-all;
             description
               "The shared secret which is known to both the RADIUS
                client and server.";
             reference
               "RFC 2865: Remote Authentication Dial In User Service";
           }
         }
         container options {
           description
             "RADIUS client options.";

           leaf timeout {
             type uint8;
             units "seconds";
             default "5";
             description
               "The number of seconds the device will wait for a
                response from a RADIUS server before trying with a
                different server.";
           }
           leaf attempts {
             type uint8;
             default "2";
             description
               "The number of times the device will send a query to
                the RADIUS servers before giving up.";
           }
         }
       }

       list user {
         if-feature local-users;
         key name;

         description
           "The list of local users configured on this device.";
         
         leaf name {
           type string;
           description
            "The user name string identifying this entry.";
         }
         leaf password {
           type crypt-hash;
           description
             "The password for this entry.";
         }
         leaf ssh-dsa {
           type binary;
           description
             "The public DSA key for this entry.";
         }
         leaf ssh-rsa {
           type binary;
           description
             "The public RSA key for this entry.";
         }
       }
     }
  }

  rpc set-current-datetime {
    nacm:default-deny-all;
    description
      "Manually set the /system/clock/current-datetime leaf
       to the specified value.

       If the /system/ntp/ntp-in-use leaf exists and
       is set to 'true', then this operation will
       fail with error-tag 'operation-failed',
       and error-app-tag value of 'ntp-active'";
    input {
      leaf current-datetime {
        description 
          "The current system date and time.";
        type yang:date-and-time;
        mandatory true;
      }
    }
  }

  rpc system-restart {
    nacm:default-deny-all;
    description
      "Request that the entire system be restarted immediately.
       A server SHOULD send an rpc reply to the client before
       restarting the system.";
  }

  rpc system-shutdown {
    nacm:default-deny-all;
    description
      "Request that the entire system be shut down immediately.
       A server SHOULD send an rpc reply to the client before
       shutting down the system.";
  }


}


	    

<CODE ENDS>

5. IANA Considerations

This document registers a URI in the IETF XML registry [RFC3688]. Following the format in RFC 3688, the following registration is requested to be made.

     URI: urn:ietf:params:xml:ns:yang:ietf-system

     Registrant Contact: The NETMOD WG of the IETF.

     XML: N/A, the requested URI is an XML namespace.
	    

This document registers a YANG module in the YANG Module Names registry [RFC6020].

  name:         ietf-system
  namespace:    urn:ietf:params:xml:ns:yang:ietf-system
  prefix:       sys
  reference:    RFC XXXX
	    

6. Security Considerations

TBD.

7. References

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, January 2004.
[RFC4252] Ylonen, T. and C. Lonvick, "The Secure Shell (SSH) Authentication Protocol", RFC 4252, January 2006.
[RFC4253] Ylonen, T. and C. Lonvick, "The Secure Shell (SSH) Transport Layer Protocol", RFC 4253, January 2006.
[RFC6242] Wasserman, M., "Using the NETCONF Protocol over Secure Shell (SSH)", RFC 6242, June 2011.
[I-D.lear-iana-timezone-database] Lear, E and P Eggert, "IANA Procedures for Maintaining the Timezone Database", Internet-Draft draft-lear-iana-timezone-database-04, May 2011.
[I-D.ietf-netconf-access-control] Bierman, A and M Bjorklund, "Network Configuration Protocol (NETCONF) Access Control Model", Internet-Draft draft-ietf-netconf-access-control-05, October 2011.
[RFC6020] Bjorklund, M., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, October 2010.
[RFC6021] Schoenwaelder, J., "Common YANG Data Types", RFC 6021, October 2010.
[RFC1321] Rivest, R., "The MD5 Message-Digest Algorithm", RFC 1321, April 1992.
[RFC2865] Rigney, C., Willens, S., Rubens, A. and W. Simpson, "Remote Authentication Dial In User Service (RADIUS)", RFC 2865, June 2000.
[RFC3418] Presuhn, R., "Management Information Base (MIB) for the Simple Network Management Protocol (SNMP)", STD 62, RFC 3418, December 2002.
[RFC5607] Nelson, D. and G. Weber, "Remote Authentication Dial-In User Service (RADIUS) Authorization for Network Access Server (NAS) Management", RFC 5607, July 2009.
[FIPS.180-3.2008] National Institute of Standards and Technology, "Secure Hash Standard", FIPS PUB 180-3, October 2008.
[IEEE-1003.1-2008] Institute of Electrical and Electronics Engineers, "POSIX.1-2008", IEEE Standard 1003.1, March 2008.

Authors' Addresses

Andy Bierman Brocade EMail: andy.bierman@brocade.com
Martin Bjorklund Tail-f Systems EMail: mbj@tail-f.com