Internet-Draft A YANG Network Model for ACs March 2023
Boucadair, et al. Expires 10 September 2023 [Page]
Workgroup:
Operations and Management Area Working Group
Internet-Draft:
draft-boro-opsawg-ntw-attachment-circuit-02
Published:
Intended Status:
Standards Track
Expires:
Authors:
M. Boucadair, Ed.
Orange
R. Roberts
Juniper
O. G. D. Dios
Telefonica
S. B. Giraldo
Nokia
B. Wu
Huawei Technologies

A Network YANG Data Model for Attachment Circuits

Abstract

This document specifies a network model for attachment circuits. The model can be used for the provisioning of attachment circuits prior or during service provisioning (e.g., Network Slice Service). A companion service model is specified in [I-D.boro-opsawg-teas-attachment-circuit].

The module augments the Service Attachment Point (SAP) model with the detailed information for the provisioning of attachment circuits in Provider Edges (PEs).

Discussion Venues

This note is to be removed before publishing as an RFC.

Discussion of this document takes place on the Operations and Management Area Working Group Working Group mailing list (opsawg@ietf.org), which is archived at https://mailarchive.ietf.org/arch/browse/opsawg/.

Source for this draft and an issue tracker can be found at https://github.com/boucadair/network-attachment-circuits.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 10 September 2023.

Table of Contents

1. Introduction

The procedure to provision a service in a service provider network may depend on the practices adopted by a service provider, including the flow put in place for the provisioning of advanced network services and how they are bound to an attachment circuit (AC). For example, the same attachment circuit may be used to host multiple services (e.g., Layer 2 VPN, Slice Services, or Layer 3 VPN). In order to avoid service interference and redundant information in various locations, a service provider may expose an interface to manage attachment circuits network-wide. Customers can then request a base attachment circuit to be put in place, and then refer to that AC when requesting services to be bound to that AC. [I-D.boro-opsawg-teas-attachment-circuit] specifies a data model for managing attachment circuits as a service.

This document specifies a network model for attachment circuits ("ietf-ac-ntw"). The model can be used for the provisioning of attachment circuits prior or during service provisioning (e.g., Network Slice Service).

The document leverages [RFC9182] and [RFC9291] by adopting an AC provisioning structure that uses data nodes that are defined in these RFCs. Some refinements were introduced to cover, not only conventional service provider networks, but also specifics of other target deployments (cloud, for example).

The AC network model is designed as an augmnetation to the Service Attachment Point (SAP) model [I-D.ietf-opsawg-sap]. An AC can be bound to a single or multiple SAPs. Likewise, the model is designed to accomdate deployments where a SAP can be bound to one or multiple ACs.

                    .---.
                    |CE6|
                    '-+-'
                   ac |        .---.                    .---.
                      |        |CE5+----------+---------+CE2|
               .------+-----.  '---'          |         '---'
               |            |                 |ac
               |            |                 |
             .-+-.       .-+-.              .-+-.
           .-+sap+-------+sap+-.          .-+sap+-------------.
           | '---'       '---' |          | '---'             |
.---.    .-+-.                 |          |                   |
|CE1+----+sap|      PE1        |          |         PE2       |
'---' ac '-+-'                 |          |                   |
           '-------------------'          '-------------------'

           .-------------------.          .-------------------.
           |                   |          |                 .-+-. ac .---.
           |         PE3       |          |        PE4      |sap+----+CE5|
           |                   |          |                 '---'    '---'
           |             .---. |          | .---. .---. .---. |
           '-------------+sap+-'          '-+sap+-+sap+-+sap+-'
                         '-+-'              '-+-' '-+-' '-+-'
                           |ac                |     |ac   |ac
                         .-+-.                |   .-+-.   |
                         |CE3+--------ac------'   |CE4+---'
                         '---'                    '---'
Figure 1: Attachment Circuits Examples

The AC network model uses the AC common model defined in [I-D.boro-opsawg-teas-common-ac].

The YANG data model in this document conforms to the Network Management Datastore Architecture (NMDA) defined in [RFC8342].

2. Conventions and Definitions

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.

The reader should be familiar with the terms defined in Section 2 of [I-D.ietf-opsawg-sap].

This document uses the term "network model" as defined in Section 2.1 of [RFC8969].

The meanings of the symbols in the YANG tree diagrams are defined in [RFC8340].

This document uses the following terms:

Bearer:

A physical or logical link that connects a customer node (or site) to a provider network. A bearer can be a wireless or wired link. One or multiple technologies can be used to build a bearer. The bearer type can be specified by a customer.

The operator allocates a unique bearer reference to identify a bearer within its network (e.g., customer line identifier). Such a reference can be retrieved by a customer and used in subsequent service placement requests to unambiguously identify where a service is to be bound.

The concept of bearer can be generalized to refer to the required underlying connection for the provisioning of an attachment circuit. One or multiple attachment circuits may be hosted over the same bearer (e.g., multiple VLANs on the same bearer that is provided by a physical link).

Network controller:

Denotes a functional entity responsible for the management of the service provider network.

Service orchestrator:

Refers to a functional entity that interacts with the customer of a network service. The service orchestrator is typically responsible for the attachment circuits, the Provider Edge (PE) selection, and requesting the activation of the requested service to a network controller.

Service provider network:

A network that is able to provide network services (e.g., Network Slice Services).

Service provider:

A service provider that offers network services (e.g., Network Slice Services).

Customer Terminating Point (CTP):

Refers to a customer-owned endpoint that terminates an attachment circuit. Such an endpoint can be a Customer Edge (CE), a Network Function (NF), a peer ASBR, etc.

3. Sample Uses of the Attachment Circuit Data Models

Figure 2 shows the positioning of the AC network model in the overall service delivery process.

                          +---------------+
                          |   Customer    |
                          +-------+-------+
          Customer Service Model  |
        e.g., slice-svc, ac-svc   |
                          +-------+-------+
                          |    Service    |
                          | Orchestration |
                          +-------+-------+
           Network Model          |
     e.g., l3vpn-ntw, sap, ac-ntw |
                          +-------+-------+
                          |   Network     |
                          | Orchestration |
                          +-------+-------+
    Network Configuration Model   |
                      +-----------+-----------+
                      |                       |
             +--------+------+       +--------+------+
             |    Domain     |       |     Domain    |
             | Orchestration |       | Orchestration |
             +---+-----------+       +--------+------+
  Device         |        |                   |
  Configuration  |        |                   |
  Model          |        |                   |
            +----+----+   |                   |
            | Config  |   |                   |
            | Manager |   |                   |
            +----+----+   |                   |
                 |        |                   |
                 | NETCONF/CLI..................
                 |        |                   |
               +--------------------------------+
 +----+ Bearer |                                | Bearer +----+
 |CTP +--------+            Network             +--------+ CTP|
 +----+        |                                |        +----+
               +--------------------------------+
  Site A                                                  Site B
Figure 2: An Example of the Network AC Model Usage

4. Description of the Attachment Circuit YANG Module

4.1. Overall Structure of the Module

The overall tree structure of the module is shown in Figure 3. A node can host one or more SAPs as per [I-D.ietf-opsawg-sap]. Each SAP terminate one or multiple ACs. The SAP model in [I-D.ietf-opsawg-sap] is thus augmented with required AC-related information. Also, in order to ease the correlation between the AC exposed at the service layer and the one that is actually provisioned in the network operation, a reference to the AC exposed to the customer ('ac-ref') is stored in the 'ac-ntw' module.

Unlike the AC service model, an AC is uniquely identified within the scope of a node, not a network. An AC can be characterized using Layer 2 connectivity, Layer 3 connectivity, routing protocols, OAM, and security considerations. In order to factorize a set of data that is provisioned for a set of ACs, a set of profiles can be defined at the network level, and then called under the node level. The information contained in the profile are thus inherited, unless the corresponding data node is refined at the AC level. In such as case, the value provided at the AC level takes precedence over the global one.

  augment /nw:networks/nw:network:
    +--rw ac-profile* [name]
       ...
  augment /nw:networks/nw:network/nw:node/sap:service/sap:sap:
    +--rw ac* [name]
       +--rw name                 string
       +--rw ac-ref?              ac-svc:attachment-circuit-reference
       +--rw ac-profile* [profile-id]
       |  +--rw profile-id    -> /nw:networks/network/ac-profile/name
       +--rw peer-sap-id*         string
       +--rw group* [group-id]
       |  +--rw group-id      string
       |  +--rw precedence?   identityref
       +--rw status
       |  +--rw admin-status
       |  |  +--rw status?        identityref
       |  |  +--rw last-change?   yang:date-and-time
       |  +--ro oper-status
       |     +--ro status?        identityref
       |     +--ro last-change?   yang:date-and-time
       +--rw description?         string
       +--rw l2-connection
       |  ...
       +--rw ip-connection
       |  ...
       +--rw routing-protocols
       |  ...
       +--rw oam
       |  ...
       +--rw security
          ...
Figure 3: Overall Tree Structure

The full tree of the 'ac-ntw' is provided in [AC-Ntw-Tree].

4.2. L2 Connection

The Layer 2 connection tree structure is shown in Figure 4.

  augment /nw:networks/nw:network/nw:node/sap:service/sap:sap:
    +--rw ac* [name]
       +--rw name                 string
       +--rw ac-ref?              ac-svc:attachment-circuit-reference
       +--rw ac-profile* [profile-id]
       |  +--rw profile-id    -> /nw:networks/network/ac-profile/name
       +--rw description?         string
       +--rw l2-connection
       |  +--rw encapsulation
       |  |  +--rw encap-type?        identityref
       |  |  +--rw dot1q
       |  |  |  +--rw tag-type?         identityref
       |  |  |  +--rw cvlan-id?         uint16
       |  |  |  +--rw tag-operations
       |  |  |     +--rw (op-choice)?
       |  |  |     |  +--:(pop)
       |  |  |     |  |  +--rw pop?         empty
       |  |  |     |  +--:(push)
       |  |  |     |  |  +--rw push?        empty
       |  |  |     |  +--:(translate)
       |  |  |     |     +--rw translate?   empty
       |  |  |     +--rw tag-1?             dot1q-types:vlanid
       |  |  |     +--rw tag-1-type?
       |  |  |     |       dot1q-types:dot1q-tag-type
       |  |  |     +--rw tag-2?             dot1q-types:vlanid
       |  |  |     +--rw tag-2-type?
       |  |  |             dot1q-types:dot1q-tag-type
       |  |  +--rw priority-tagged
       |  |  |  +--rw tag-type?   identityref
       |  |  +--rw qinq
       |  |     +--rw tag-type?         identityref
       |  |     +--rw svlan-id          uint16
       |  |     +--rw cvlan-id          uint16
       |  |     +--rw tag-operations
       |  |        +--rw (op-choice)?
       |  |        |  +--:(pop)
       |  |        |  |  +--rw pop?         uint8
       |  |        |  +--:(push)
       |  |        |  |  +--rw push?        empty
       |  |        |  +--:(translate)
       |  |        |     +--rw translate?   uint8
       |  |        +--rw tag-1?             dot1q-types:vlanid
       |  |        +--rw tag-1-type?
       |  |        |       dot1q-types:dot1q-tag-type
       |  |        +--rw tag-2?             dot1q-types:vlanid
       |  |        +--rw tag-2-type?
       |  |                dot1q-types:dot1q-tag-type
       |  +--rw (l2-service)?
       |  |  +--:(l2-tunnel-service)
       |  |  |  +--rw l2-tunnel-service
       |  |  |     +--rw type?         identityref
       |  |  |     +--rw pseudowire
       |  |  |     |  +--rw vcid?      uint32
       |  |  |     |  +--rw far-end?   union
       |  |  |     +--rw vpls
       |  |  |     |  +--rw vcid?      uint32
       |  |  |     |  +--rw far-end*   union
       |  |  |     +--rw vxlan
       |  |  |        +--rw vni-id             uint32
       |  |  |        +--rw peer-mode?         identityref
       |  |  |        +--rw peer-ip-address*   inet:ip-address
       |  |  +--:(l2vpn)
       |  |     +--rw l2vpn-id?            vpn-common:vpn-id
       |  +--rw l2-termination-point?      string
       |  +--rw local-bridge-reference?    string
       |  +--rw bearer-reference?          string
       |  |       {vpn-common:bearer-reference}?
       |  +--rw lag-interface {vpn-common:lag-interface}?
       |     +--rw lag-interface-id?   string
       |     +--rw member-link-list
       |        +--rw member-link* [name]
       |           +--rw name    string
       +--rw ip-connection
       |  ...
       +--rw routing-protocols
       |  ...
       +--rw oam
       |  ...
       +--rw security
          ...
Figure 4: Layer 2 Connection Tree Structure

4.3. IP Connection

The Layer 3 connection tree structure is shown in Figure 5.

  augment /nw:networks/nw:network/nw:node/sap:service/sap:sap:
    +--rw ac* [name]
       +--rw name                 string
       +--rw ac-ref?              ac-svc:attachment-circuit-reference
       +--rw ac-profile* [profile-id]
       |  +--rw profile-id    -> /nw:networks/network/ac-profile/name
       +--rw description?         string
       +--rw l2-connection
       |  ...
       +--rw ip-connection
       |  +--rw l3-termination-point?   string
       |  +--rw ipv4 {vpn-common:ipv4}?
       |  |  +--rw local-address?
       |  |  |       inet:ipv4-address
       |  |  +--rw prefix-length?                           uint8
       |  |  +--rw address-allocation-type?
       |  |  |       identityref
       |  |  +--rw (allocation-type)?
       |  |     +--:(dynamic)
       |  |     |  +--rw (address-assign)?
       |  |     |  |  +--:(number)
       |  |     |  |  |  +--rw number-of-dynamic-address?   uint16
       |  |     |  |  +--:(explicit)
       |  |     |  |     +--rw customer-addresses
       |  |     |  |        +--rw address-pool* [pool-id]
       |  |     |  |           +--rw pool-id          string
       |  |     |  |           +--rw start-address
       |  |     |  |           |       inet:ipv4-address
       |  |     |  |           +--rw end-address?
       |  |     |  |                   inet:ipv4-address
       |  |     |  +--rw (provider-dhcp)?
       |  |     |  |  +--:(dhcp-service-type)
       |  |     |  |  |  +--rw dhcp-service-type?
       |  |     |  |  |          enumeration
       |  |     |  |  +--:(service-type)
       |  |     |  |     +--rw (service-type)?
       |  |     |  |        +--:(relay)
       |  |     |  |           +--rw server-ip-address*
       |  |     |  |                   inet:ipv4-address
       |  |     |  +--rw (dhcp-relay)?
       |  |     |     +--:(customer-dhcp-servers)
       |  |     |        +--rw customer-dhcp-servers
       |  |     |           +--rw server-ip-address*
       |  |     |                   inet:ipv4-address
       |  |     +--:(static-addresses)
       |  |        +--rw address* [address-id]
       |  |           +--rw address-id          string
       |  |           +--rw customer-address?   inet:ipv4-address
       |  +--rw ipv6 {vpn-common:ipv6}?
       |     +--rw local-address?
       |     |       inet:ipv6-address
       |     +--rw prefix-length?                           uint8
       |     +--rw address-allocation-type?
       |     |       identityref
       |     +--rw (allocation-type)?
       |        +--:(dynamic)
       |        |  +--rw (address-assign)?
       |        |  |  +--:(number)
       |        |  |  |  +--rw number-of-dynamic-address?   uint16
       |        |  |  +--:(explicit)
       |        |  |     +--rw customer-addresses
       |        |  |        +--rw address-pool* [pool-id]
       |        |  |           +--rw pool-id          string
       |        |  |           +--rw start-address
       |        |  |           |       inet:ipv6-address
       |        |  |           +--rw end-address?
       |        |  |                   inet:ipv6-address
       |        |  +--rw (provider-dhcp)?
       |        |  |  +--:(dhcp-service-type)
       |        |  |  |  +--rw dhcp-service-type?
       |        |  |  |          enumeration
       |        |  |  +--:(service-type)
       |        |  |     +--rw (service-type)?
       |        |  |        +--:(relay)
       |        |  |           +--rw server-ip-address*
       |        |  |                   inet:ipv6-address
       |        |  +--rw (dhcp-relay)?
       |        |     +--:(customer-dhcp-servers)
       |        |        +--rw customer-dhcp-servers
       |        |           +--rw server-ip-address*
       |        |                   inet:ipv6-address
       |        +--:(static-addresses)
       |           +--rw address* [address-id]
       |              +--rw address-id          string
       |              +--rw customer-address?   inet:ipv6-address
       +--rw routing-protocols
       |  ...
       +--rw oam
       |  ...
       +--rw security
          ...
Figure 5: IP Connection Tree Structure

4.4. Routing

The routing tree structure is shown in Figure 6.

module: ietf-ac-ntw
  augment /nw:networks/nw:network:
    +--rw ac-profile* [name]
       +--rw name                 string
       +--rw l2-connection
       +--rw ip-connection
       +--rw routing-protocols
       |  +--rw routing-protocol* [id]
       |     +--rw id      string
       |     +--rw type?   identityref
       |     +--rw bgp
       |     |  +--rw description?              string
       |     |  +--rw local-as?                 inet:as-number
       |     |  +--rw peer-as                   inet:as-number
       |     |  +--rw address-family?           identityref
       |     |  +--rw multihop?                 uint8
       |     |  +--rw as-override?              boolean
       |     |  +--rw allow-own-as?             uint8
       |     |  +--rw prepend-global-as?        boolean
       |     |  +--rw send-default-route?       boolean
       |     |  +--rw site-of-origin?           rt-types:route-origin
       |     |  +--rw ipv6-site-of-origin?
       |     |  |       rt-types:ipv6-route-origin
       |     |  +--rw redistribute-connected* [address-family]
       |     |  |  +--rw address-family    identityref
       |     |  |  +--rw enable?           boolean
       |     |  +--rw bgp-max-prefix
       |     |  |  +--rw max-prefix?          uint32
       |     |  |  +--rw warning-threshold?   decimal64
       |     |  |  +--rw violate-action?      enumeration
       |     |  |  +--rw restart-timer?       uint32
       |     |  +--rw bgp-timers
       |     |     +--rw keepalive?   uint16
       |     |     +--rw hold-time?   uint16
       |     +--rw ospf
       |     |  +--rw address-family?   identityref
       |     |  +--rw area-id           yang:dotted-quad
       |     |  +--rw metric?           uint16
       |     |  +--rw max-lsa?          uint32
       |     +--rw isis
       |     |  +--rw address-family?   identityref
       |     |  +--rw area-address      area-address
       |     |  +--rw level?            identityref
       |     |  +--rw metric?           uint16
       |     |  +--rw mode?             enumeration
       |     +--rw rip
       |     |  +--rw address-family?   identityref
       |     |  +--rw timers
       |     |  |  +--rw update-interval?     uint16
       |     |  |  +--rw invalid-interval?    uint16
       |     |  |  +--rw holddown-interval?   uint16
       |     |  |  +--rw flush-interval?      uint16
       |     |  +--rw default-metric?   uint8
       |     +--rw vrrp
       |        +--rw address-family?   identityref
       |        +--rw ping-reply?       boolean
       +--rw oam
          ...
  augment /nw:networks/nw:network/nw:node/sap:service/sap:sap:
    +--rw ac* [name]
       +--rw name                 string
       +--rw ac-ref?              ac-svc:attachment-circuit-reference
       +--rw ac-profile* [profile-id]
       |  +--rw profile-id    -> /nw:networks/network/ac-profile/name
       +--rw description?         string
       +--rw l2-connection
       |  ...
       +--rw ip-connection
       |  ...
       +--rw routing-protocols
       |  +--rw routing-protocol* [id]
       |     +--rw id                  string
       |     +--rw type?               identityref
       |     +--rw routing-profiles* [id]
       |     |  +--rw id      leafref
       |     |  +--rw type?   identityref
       |     +--rw static
       |     |  +--rw cascaded-lan-prefixes
       |     |     +--rw ipv4-lan-prefixes* [lan next-hop]
       |     |     |       {vpn-common:ipv4}?
       |     |     |  +--rw lan           inet:ipv4-prefix
       |     |     |  +--rw lan-tag?      string
       |     |     |  +--rw next-hop      union
       |     |     |  +--rw metric?       uint32
       |     |     |  +--rw bfd-enable?   boolean {vpn-common:bfd}?
       |     |     |  +--rw preference?   uint32
       |     |     |  +--rw status
       |     |     |     +--rw admin-status
       |     |     |     |  +--rw status?        identityref
       |     |     |     |  +--rw last-change?   yang:date-and-time
       |     |     |     +--ro oper-status
       |     |     |        +--ro status?        identityref
       |     |     |        +--ro last-change?   yang:date-and-time
       |     |     +--rw ipv6-lan-prefixes* [lan next-hop]
       |     |             {vpn-common:ipv6}?
       |     |        +--rw lan           inet:ipv4-prefix
       |     |        +--rw lan-tag?      string
       |     |        +--rw next-hop      union
       |     |        +--rw metric?       uint32
       |     |        +--rw bfd-enable?   boolean {vpn-common:bfd}?
       |     |        +--rw preference?   uint32
       |     |        +--rw status
       |     |           +--rw admin-status
       |     |           |  +--rw status?        identityref
       |     |           |  +--rw last-change?   yang:date-and-time
       |     |           +--ro oper-status
       |     |              +--ro status?        identityref
       |     |              +--ro last-change?   yang:date-and-time
       |     +--rw bgp
       |     |  +--rw peer-groups
       |     |  |  +--rw peer-group* [name]
       |     |  |     +--rw name                      string
       |     |  |     +--rw local-address?            union
       |     |  |     +--rw description?              string
       |     |  |     +--rw local-as?                 inet:as-number
       |     |  |     +--rw peer-as                   inet:as-number
       |     |  |     +--rw address-family?           identityref
       |     |  |     +--rw multihop?                 uint8
       |     |  |     +--rw as-override?              boolean
       |     |  |     +--rw allow-own-as?             uint8
       |     |  |     +--rw prepend-global-as?        boolean
       |     |  |     +--rw send-default-route?       boolean
       |     |  |     +--rw site-of-origin?
       |     |  |     |       rt-types:route-origin
       |     |  |     +--rw ipv6-site-of-origin?
       |     |  |     |       rt-types:ipv6-route-origin
       |     |  |     +--rw redistribute-connected* [address-family]
       |     |  |     |  +--rw address-family    identityref
       |     |  |     |  +--rw enable?           boolean
       |     |  |     +--rw bgp-max-prefix
       |     |  |     |  +--rw max-prefix?          uint32
       |     |  |     |  +--rw warning-threshold?   decimal64
       |     |  |     |  +--rw violate-action?      enumeration
       |     |  |     |  +--rw restart-timer?       uint32
       |     |  |     +--rw bgp-timers
       |     |  |     |  +--rw keepalive?   uint16
       |     |  |     |  +--rw hold-time?   uint16
       |     |  |     +--rw authentication
       |     |  |        +--rw enable?            boolean
       |     |  |        +--rw keying-material
       |     |  |           +--rw (option)?
       |     |  |              +--:(ao)
       |     |  |              |  +--rw enable-ao?          boolean
       |     |  |              |  +--rw ao-keychain?
       |     |  |              |          key-chain:key-chain-ref
       |     |  |              +--:(md5)
       |     |  |              |  +--rw md5-keychain?
       |     |  |              |          key-chain:key-chain-ref
       |     |  |              +--:(explicit)
       |     |  |                 +--rw key-id?             uint32
       |     |  |                 +--rw key?                string
       |     |  |                 +--rw crypto-algorithm?
       |     |  |                         identityref
       |     |  +--rw neighbor* [remote-address]
       |     |     +--rw remote-address            inet:ip-address
       |     |     +--rw local-address?            union
       |     |     +--rw peer-group?
       |     |     |       -> ../../peer-groups/peer-group/name
       |     |     +--rw description?              string
       |     |     +--rw local-as?                 inet:as-number
       |     |     +--rw peer-as                   inet:as-number
       |     |     +--rw address-family?           identityref
       |     |     +--rw multihop?                 uint8
       |     |     +--rw as-override?              boolean
       |     |     +--rw allow-own-as?             uint8
       |     |     +--rw prepend-global-as?        boolean
       |     |     +--rw send-default-route?       boolean
       |     |     +--rw site-of-origin?
       |     |     |       rt-types:route-origin
       |     |     +--rw ipv6-site-of-origin?
       |     |     |       rt-types:ipv6-route-origin
       |     |     +--rw redistribute-connected* [address-family]
       |     |     |  +--rw address-family    identityref
       |     |     |  +--rw enable?           boolean
       |     |     +--rw bgp-max-prefix
       |     |     |  +--rw max-prefix?          uint32
       |     |     |  +--rw warning-threshold?   decimal64
       |     |     |  +--rw violate-action?      enumeration
       |     |     |  +--rw restart-timer?       uint32
       |     |     +--rw bgp-timers
       |     |     |  +--rw keepalive?   uint16
       |     |     |  +--rw hold-time?   uint16
       |     |     +--rw authentication
       |     |     |  +--rw enable?            boolean
       |     |     |  +--rw keying-material
       |     |     |     +--rw (option)?
       |     |     |        +--:(ao)
       |     |     |        |  +--rw enable-ao?          boolean
       |     |     |        |  +--rw ao-keychain?
       |     |     |        |          key-chain:key-chain-ref
       |     |     |        +--:(md5)
       |     |     |        |  +--rw md5-keychain?
       |     |     |        |          key-chain:key-chain-ref
       |     |     |        +--:(explicit)
       |     |     |           +--rw key-id?             uint32
       |     |     |           +--rw key?                string
       |     |     |           +--rw crypto-algorithm?   identityref
       |     |     +--rw status
       |     |        +--rw admin-status
       |     |        |  +--rw status?        identityref
       |     |        |  +--rw last-change?   yang:date-and-time
       |     |        +--ro oper-status
       |     |           +--ro status?        identityref
       |     |           +--ro last-change?   yang:date-and-time
       |     +--rw ospf
       |     |  +--rw address-family?   identityref
       |     |  +--rw area-id           yang:dotted-quad
       |     |  +--rw metric?           uint16
       |     |  +--rw sham-links {vpn-common:rtg-ospf-sham-link}?
       |     |  |  +--rw sham-link* [target-site]
       |     |  |     +--rw target-site    string
       |     |  |     +--rw metric?        uint16
       |     |  +--rw max-lsa?          uint32
       |     |  +--rw authentication
       |     |  |  +--rw enable?            boolean
       |     |  |  +--rw keying-material
       |     |  |     +--rw (option)?
       |     |  |        +--:(auth-key-chain)
       |     |  |        |  +--rw key-chain?
       |     |  |        |          key-chain:key-chain-ref
       |     |  |        +--:(auth-key-explicit)
       |     |  |           +--rw key-id?             uint32
       |     |  |           +--rw key?                string
       |     |  |           +--rw crypto-algorithm?   identityref
       |     |  +--rw status
       |     |     +--rw admin-status
       |     |     |  +--rw status?        identityref
       |     |     |  +--rw last-change?   yang:date-and-time
       |     |     +--ro oper-status
       |     |        +--ro status?        identityref
       |     |        +--ro last-change?   yang:date-and-time
       |     +--rw isis
       |     |  +--rw address-family?   identityref
       |     |  +--rw area-address      area-address
       |     |  +--rw level?            identityref
       |     |  +--rw metric?           uint16
       |     |  +--rw mode?             enumeration
       |     |  +--rw authentication
       |     |  |  +--rw enable?            boolean
       |     |  |  +--rw keying-material
       |     |  |     +--rw (option)?
       |     |  |        +--:(auth-key-chain)
       |     |  |        |  +--rw key-chain?
       |     |  |        |          key-chain:key-chain-ref
       |     |  |        +--:(auth-key-explicit)
       |     |  |           +--rw key-id?             uint32
       |     |  |           +--rw key?                string
       |     |  |           +--rw crypto-algorithm?   identityref
       |     |  +--rw status
       |     |     +--rw admin-status
       |     |     |  +--rw status?        identityref
       |     |     |  +--rw last-change?   yang:date-and-time
       |     |     +--ro oper-status
       |     |        +--ro status?        identityref
       |     |        +--ro last-change?   yang:date-and-time
       |     +--rw rip
       |     |  +--rw address-family?   identityref
       |     |  +--rw timers
       |     |  |  +--rw update-interval?     uint16
       |     |  |  +--rw invalid-interval?    uint16
       |     |  |  +--rw holddown-interval?   uint16
       |     |  |  +--rw flush-interval?      uint16
       |     |  +--rw default-metric?   uint8
       |     |  +--rw authentication
       |     |  |  +--rw enable?            boolean
       |     |  |  +--rw keying-material
       |     |  |     +--rw (option)?
       |     |  |        +--:(auth-key-chain)
       |     |  |        |  +--rw key-chain?
       |     |  |        |          key-chain:key-chain-ref
       |     |  |        +--:(auth-key-explicit)
       |     |  |           +--rw key?                string
       |     |  |           +--rw crypto-algorithm?   identityref
       |     |  +--rw status
       |     |     +--rw admin-status
       |     |     |  +--rw status?        identityref
       |     |     |  +--rw last-change?   yang:date-and-time
       |     |     +--ro oper-status
       |     |        +--ro status?        identityref
       |     |        +--ro last-change?   yang:date-and-time
       |     +--rw vrrp
       |        +--rw address-family?       identityref
       |        +--rw vrrp-group?           uint8
       |        +--rw backup-peer?          inet:ip-address
       |        +--rw virtual-ip-address*   inet:ip-address
       |        +--rw priority?             uint8
       |        +--rw ping-reply?           boolean
       |        +--rw status
       |           +--rw admin-status
       |           |  +--rw status?        identityref
       |           |  +--rw last-change?   yang:date-and-time
       |           +--ro oper-status
       |              +--ro status?        identityref
       |              +--ro last-change?   yang:date-and-time
       +--rw oam
       |  ...
       +--rw security
          ...
Figure 6: Rotuing Tree Structure

4.5. OAM

The OAM tree structure is shown in Figure 7.

  augment /nw:networks/nw:network:
    +--rw ac-profile* [name]
       +--rw name                 string
       +--rw l2-connection
       +--rw ip-connection
       +--rw routing-protocols
       |  ...
       +--rw oam
          +--rw bfd {vpn-common:bfd}?
             +--rw session-type?               identityref
             +--rw desired-min-tx-interval?    uint32
             +--rw required-min-rx-interval?   uint32
             +--rw local-multiplier?           uint8
             +--rw holdtime?                   uint32
  augment /nw:networks/nw:network/nw:node/sap:service/sap:sap:
    +--rw ac* [name]
       +--rw name                 string
       +--rw ac-ref?              ac-svc:attachment-circuit-reference
       +--rw ac-profile* [profile-id]
       |  +--rw profile-id    -> /nw:networks/network/ac-profile/name
       +--rw description?         string
       +--rw l2-connection
       |  ...
       +--rw ip-connection
       |  ...
       +--rw routing-protocols
       |  ...
       +--rw oam
       |  +--rw bfd
       |     +--rw profile?                    ac-svc:bfd-profile-reference
       |     +--rw session-type?               identityref
       |     +--rw desired-min-tx-interval?    uint32
       |     +--rw required-min-rx-interval?   uint32
       |     +--rw local-multiplier?           uint8
       |     +--rw holdtime?                   uint32
       |     +--rw authentication!
       |     |  +--rw key-chain?    key-chain:key-chain-ref
       |     |  +--rw meticulous?   boolean
       |     +--rw status
       |        +--rw admin-status
       |        |  +--rw status?        identityref
       |        |  +--rw last-change?   yang:date-and-time
       |        +--ro oper-status
       |           +--ro status?        identityref
       |           +--ro last-change?   yang:date-and-time
       +--rw security
          ...
Figure 7: OAM Tree Structure

4.6. Security

The security tree structure is shown in Figure 8.

  augment /nw:networks/nw:network/nw:node/sap:service/sap:sap:
    +--rw ac* [name]
       +--rw name                 string
       +--rw ac-ref?              ac-svc:attachment-circuit-reference
       +--rw ac-profile* [profile-id]
       |  +--rw profile-id    -> /nw:networks/network/ac-profile/name
       +--rw description?         string
       +--rw l2-connection
       |  ...
       +--rw ip-connection
       |  ...
       +--rw routing-protocols
       |  ...
       +--rw oam
       |  ...
       +--rw security
          +--rw encryption {vpn-common:encryption}?
          |  +--rw enabled?   boolean
          |  +--rw layer?     enumeration
          +--rw encryption-profile
             +--rw (profile)?
                +--:(provider-profile)
                |  +--rw profile-name?         leafref
                +--:(customer-profile)
                   +--rw customer-key-chain?
                           key-chain:key-chain-ref
Figure 8: Security Tree Structure

5. YANG Module

This module uses types defined in [RFC6991], [RFC8177], [RFC8294], [RFC8343], [RFC9181], [I-D.boro-opsawg-teas-common-ac], and IEEE Std 802.1Qcp.

<CODE BEGINS> file "ietf-ac-ntw@2022-11-30.yang"

module ietf-ac-ntw {
  yang-version 1.1;
  namespace "urn:ietf:params:xml:ns:yang:ietf-ac-ntw";
  prefix ac-ntw;

  import ietf-vpn-common {
    prefix vpn-common;
    reference
      "RFC 9181: A Common YANG Data Model for Layer 2 and Layer 3
                 VPNs";
  }
  import ietf-inet-types {
    prefix inet;
    reference
      "RFC 6991: Common YANG Data Types, Section 4";
  }
  import ietf-key-chain {
    prefix key-chain;
    reference
      "RFC 8177: YANG Data Model for Key Chains";
  }
  import ietf-routing-types {
    prefix rt-types;
    reference
      "RFC 8294: Common YANG Data Types for the Routing Area";
  }
  import ietf-interfaces {
    prefix if;
    reference
      "RFC 8343: A YANG Data Model for Interface Management";
  }
  import ieee802-dot1q-types {
    prefix dot1q-types;
    reference
      "IEEE Std 802.1Qcp: Bridges and Bridged Networks--
                          Amendment 30: YANG Data Model";
  }
  import ietf-network {
    prefix nw;
    reference
      "RFC 8345: A YANG Data Model for Network Topologies,
                 Section 6.1";
  }
  import ietf-sap-ntw {
    prefix sap;
    reference
      "RFC SSSS: A YANG Network Model for Service Attachment
                 Points (SAPs)";
  }
  import ietf-ac-common {
    prefix ac-common;
    reference
      "RFC CCCC: A Common YANG Data Model for Attachment Circuits";
  }
  import ietf-ac-svc {
    prefix ac-svc;
    reference
      "RFC SSSS: YANG Service Data Models for Attachment Circuits";
  }

  organization
    "IETF OPSAWG (Operations and Management Area Working Group)";
  contact
    "WG Web:   <https://datatracker.ietf.org/wg/opsawg/>
     WG List:  <mailto:opsawg@ietf.org>

     Editor:   Mohamed Boucadair
               <mailto:mohamed.boucadair@orange.com>
     Author:   Richard Roberts
               <mailto:rroberts@juniper.net>";
  description
    "This YANG module defines a YANG model for the management of
     attachment circuits.

     Copyright (c) 2023 IETF Trust and the persons identified as
     authors of the code.  All rights reserved.

     Redistribution and use in source and binary forms, with or
     without modification, is permitted pursuant to, and subject
     to the license terms contained in, the Revised BSD License
     set forth in Section 4.c of the IETF Trust's Legal Provisions
     Relating to IETF Documents
     (https://trustee.ietf.org/license-info).

     This version of this YANG module is part of RFC xxx; see the
     RFC itself for full legal notices.";

  revision 2022-11-30 {
    description
      "Initial revision.";
    reference
      "RFC xxxx: A YANG Network Data Model for Attachment Circuits";
  }

  // L2 conenction

  grouping l2-connection {
    description
      "Defines Layer 2 protocols and parameters that are required to
       enable AC connectivity.";
    container encapsulation {
      description
        "Container for Layer 2 encapsulation.";
      leaf encap-type {
        type identityref {
          base vpn-common:encapsulation-type;
        }
        description
          "Tagged interface type.";
      }
      container dot1q {
        when "derived-from-or-self(../encap-type, "
           + "'vpn-common:dot1q')" {
          description
            "Only applies when the type of the tagged interface is
             'dot1q'.";
        }
        description
          "Tagged interface.";
        uses ac-common:dot1q;
        container tag-operations {
          description
            "Sets the tag manipulation policy for this AC. It defines
             a set of tag manipulations that allow for the insertion,
             removal, or rewriting of 802.1Q VLAN tags. These
             operations are indicated for the CE-PE direction.
             By default, tag operations are symmetric. As such, the
             reverse tag operation is assumed on the PE-CE
             direction.";
          choice op-choice {
            description
              "Selects the tag rewriting policy for an AC.";
            leaf pop {
              type empty;
              description
                "Pop the outer tag.";
            }
            leaf push {
              type empty;
              description
                "Pushes one or two tags defined by the tag-1 and
                 tag-2 leaves.  It is assumed that, absent any
                 policy, the default value of 0 will be used for
                 the PCP  setting.";
            }
            leaf translate {
              type empty;
              description
                "Translates the outer tag to one or two tags. PCP
                 bits are preserved.";
            }
          }
          leaf tag-1 {
            when 'not(../pop)';
            type dot1q-types:vlanid;
            description
              "A first tag to be used for push or translate
               operations. This tag will be used as the outermost tag
               as a result of the tag operation.";
          }
          leaf tag-1-type {
            type dot1q-types:dot1q-tag-type;
            default "dot1q-types:s-vlan";
            description
              "Specifies a specific 802.1Q tag type of tag-1.";
          }
          leaf tag-2 {
            when '(../translate)';
            type dot1q-types:vlanid;
            description
              "A second tag to be used for translation.";
          }
          leaf tag-2-type {
            type dot1q-types:dot1q-tag-type;
            default "dot1q-types:c-vlan";
            description
              "Specifies a specific 802.1Q tag type of tag-2.";
          }
        }
      }
      container priority-tagged {
        when "derived-from-or-self(../encap-type, "
           + "'vpn-common:priority-tagged')" {
          description
            "Only applies when the type of the tagged interface is
             'priority-tagged'.";
        }
        description
          "Priority tagged container.";
        uses ac-common:priority-tagged;
      }
      container qinq {
        when "derived-from-or-self(../encap-type, "
           + "'vpn-common:qinq')" {
          description
            "Only applies when the type of the tagged interface is
             'QinQ'.";
        }
        description
          "Includes QinQ parameters.";
        uses ac-common:qinq;
        container tag-operations {
          description
            "Sets the tag manipulation policy for this AC. It defines
             a set of tag manipulations that allow for the insertion,
             removal, or rewriting of 802.1Q VLAN tags. These
             operations are indicated for the CE-PE direction.
             By default, tag operations are symmetric. As such, the
             reverse tag operation is assumed on the PE-CE
             direction.";
          choice op-choice {
            description
              "Selects the tag rewriting policy for a AC.";
            leaf pop {
              type uint8 {
                range "1|2";
              }
              description
                "Pops one or two tags as a function of the indicated
                 pop value.";
            }
            leaf push {
              type empty;
              description
                "Pushes one or two tags defined by the tag-1 and
                 tag-2 leaves. It is assumed that, absent any
                 policy, the default value of 0 will be used for
                 PCP setting.";
            }
            leaf translate {
              type uint8 {
                range "1|2";
              }
              description
                "Translates one or two outer tags. PCP bits are
                 preserved. The following operations are supported:

                 - translate 1 with tag-1 leaf is provided: only the
                   outermost tag is translated to the value in tag-1.

                 - translate 2 with both tag-1 and tag-2 leaves are
                   provided: both outer and inner tags are translated
                   to the values in tag-1 and tag-2, respectively.

                 - translate 2 with tag-1 leaf is provided: the
                   outer tag is popped while the inner tag is
                   translated to the value in tag-1.";
            }
          }
          leaf tag-1 {
            when 'not(../pop)';
            type dot1q-types:vlanid;
            description
              "A first tag to be used for push or translate
               operations. This tag will be used as the outermost tag
               as a result of the tag operation.";
          }
          leaf tag-1-type {
            type dot1q-types:dot1q-tag-type;
            default "dot1q-types:s-vlan";
            description
              "Specifies a specific 802.1Q tag type of tag-1.";
          }
          leaf tag-2 {
            when 'not(../pop)';
            type dot1q-types:vlanid;
            description
              "A second tag to be used for push or translate
               operations.";
          }
          leaf tag-2-type {
            type dot1q-types:dot1q-tag-type;
            default "dot1q-types:c-vlan";
            description
              "Specifies a specific 802.1Q tag type of tag-2.";
          }
        }
      }
    }
    choice l2-service {
      description
        "The Layer 2 connectivity service can be provided by
         indicating a pointer to an L2VPN or by specifying a Layer 2
         tunnel service.";
      container l2-tunnel-service {
        description
          "Defines a Layer 2 tunnel termination.";
        uses ac-common:l2-tunnel-service;
      }
      case l2vpn {
        leaf l2vpn-id {
          type vpn-common:vpn-id;
          description
            "Indicates the L2VPN service associated with an
             Integrated Routing and Bridging (IRB) interface.";
        }
      }
    }
  }

  grouping l2-connection-if-ref {
    description
      "Specifies Layer 2 connection paramters with interface
       references.";
    uses l2-connection;
    leaf l2-termination-point {
      type string;
      description
        "Specifies a reference to a local Layer 2 termination point,
         such as a Layer 2 sub-interface.";
    }
    leaf local-bridge-reference {
      type string;
      description
        "Specifies a local bridge reference to accommodate, e.g.,
         implementations that require internal bridging.
         A reference may be a local bridge domain.";
    }
    leaf bearer-reference {
      if-feature "vpn-common:bearer-reference";
      type string;
      description
        "This is an internal reference for the service provider to
         identify the bearer associated with this AC.";
    }
    container lag-interface {
      if-feature "vpn-common:lag-interface";
      description
        "Container for configuration of Link Aggregation Group (LAG)
         interface attributes.";
      leaf lag-interface-id {
        type string;
        description
          "LAG interface identifier.";
      }
      container member-link-list {
        description
          "Container for the member link list.";
        list member-link {
          key "name";
          description
            "Member link.";
          leaf name {
            type string;
            description
              "Member link name.";
          }
        }
      }
    }
  }

  // IPv4 connection

  grouping ipv4-connection {
    description
      "IPv4-specific parameters.";
    leaf local-address {
      type inet:ipv4-address;
      description
        "The IP address used at the provider's interface.";
    }
    uses ac-common:ipv4-allocation-type;
    choice allocation-type {
      description
        "Choice of the IPv4 address allocation.";
      case dynamic {
        description
          "When the addresses are allocated by DHCP or other
           dynamic means local to the infrastructure.";
        choice address-assign {
          default "number";
          description
            "A choice for how IPv4 addresses are assigned.";
          case number {
            leaf number-of-dynamic-address {
              type uint16;
              description
                "Specifies the number of IP addresses to be
                 assigned to the customer on this access.";
            }
          }
          case explicit {
            container customer-addresses {
              description
                "Container for customer addresses to be allocated
                 using DHCP.";
              list address-pool {
                key "pool-id";
                description
                  "Describes IP addresses to be dyncamically
                   allocated.

                   When only 'start-address' is present, it
                   represents a single address.

                   When both 'start-address' and 'end-address' are
                   specified, it implies a range inclusive of both
                   addresses.";
                leaf pool-id {
                  type string;
                  description
                    "A pool identifier for the address range from
                     'start-address' to 'end-address'.";
                }
                leaf start-address {
                  type inet:ipv4-address;
                  mandatory true;
                  description
                    "Indicates the first address in the pool.";
                }
                leaf end-address {
                  type inet:ipv4-address;
                  description
                    "Indicates the last address in the pool.";
                }
              }
            }
          }
        }
        choice provider-dhcp {
          description
            "Parameters related to DHCP-allocated addresses.
             IP addresses are allocated by DHCP, which is provided
             by the operator.";
          leaf dhcp-service-type {
            type enumeration {
              enum server {
                description
                  "Local DHCP server.";
              }
              enum relay {
                description
                  "Local DHCP relay.  DHCP requests are relayed to a
                   provider's server.";
              }
            }
            description
              "Indicates the type of DHCP service to be enabled on
               this access.";
          }
          choice service-type {
            description
              "Choice based on the DHCP service type.";
            case relay {
              description
                "Container for a list of the provider's DHCP servers
                 (i.e., 'dhcp-service-type' is set to 'relay').";
              leaf-list server-ip-address {
                type inet:ipv4-address;
                description
                  "IPv4 addresses of the provider's DHCP server, for
                   use by the local DHCP relay.";
              }
            }
          }
        }
        choice dhcp-relay {
          description
            "The DHCP relay is provided by the operator.";
          container customer-dhcp-servers {
            description
              "Container for a list of the customer's DHCP servers.";
            leaf-list server-ip-address {
              type inet:ipv4-address;
              description
                "IPv4 addresses of the customer's DHCP server.";
            }
          }
        }
      }
      case static-addresses {
        description
          "Lists the IPv4 addresses that are used.";
        list address {
          key "address-id";
          ordered-by user;
          description
            "Lists the IPv4 addresses that are used. The first
             address of the list is the primary address of the
             connection.";
          leaf address-id {
            type string;
            description
              "An identifier of the static IPv4 address.";
          }
          leaf customer-address {
            type inet:ipv4-address;
            description
              "An IPv4 address of the customer side.";
          }
        }
      }
    }
  }

  grouping ipv6-connection {
    description
      "IPv6-specific parameters.";
    leaf local-address {
      type inet:ipv6-address;
      description
        "IPv6 address of the provider side.";
    }
    uses ac-common:ipv6-allocation-type;
    choice allocation-type {
      description
        "Choice of the IPv6 address allocation.";
      case dynamic {
        description
          "When the addresses are allocated by DHCP or other
           dynamic means local to the infrastructure.";
        choice address-assign {
          default "number";
          description
            "A choice for how IPv6 addresses are assigned.";
          case number {
            leaf number-of-dynamic-address {
              type uint16;
              default "1";
              description
                "Specifies the number of IP addresses to be
                 assigned to the customer on this access.";
            }
          }
          case explicit {
            container customer-addresses {
              description
                "Container for customer addresses to be allocated
                 using DHCP.";
              list address-pool {
                key "pool-id";
                description
                  "Describes IP addresses to be dyncamically
                   allocated.

                   When only 'start-address' is present, it
                   represents a single address.

                   When both 'start-address' and 'end-address' are
                   specified, it implies a range inclusive of both
                   addresses.";
                leaf pool-id {
                  type string;
                  description
                    "A pool identifier for the address range from
                     'start-address' to 'end-address'.";
                }
                leaf start-address {
                  type inet:ipv6-address;
                  mandatory true;
                  description
                    "Indicates the first address in the pool.";
                }
                leaf end-address {
                  type inet:ipv6-address;
                  description
                    "Indicates the last address in the pool.";
                }
              }
            }
          }
        }
        choice provider-dhcp {
          description
            "Parameters related to DHCP-allocated addresses.
             IP addresses are allocated by DHCP, which is provided
             by the operator.";
          leaf dhcp-service-type {
            type enumeration {
              enum server {
                description
                  "Local DHCP server.";
              }
              enum relay {
                description
                  "Local DHCP relay. DHCP requests are relayed to
                   a provider's server.";
              }
            }
            description
              "Indicates the type of DHCP service to
               be enabled on this access.";
          }
          choice service-type {
            description
              "Choice based on the DHCP service type.";
            case relay {
              description
                "Container for a list of the provider's DHCP servers
                 (i.e., 'dhcp-service-type' is set to 'relay').";
              leaf-list server-ip-address {
                type inet:ipv6-address;
                description
                  "IPv6 addresses of the provider's DHCP server, for
                   use by the local DHCP relay.";
              }
            }
          }
        }
        choice dhcp-relay {
          description
            "The DHCP relay is provided by the operator.";
          container customer-dhcp-servers {
            description
              "Container for a list of the customer's DHCP servers.";
            leaf-list server-ip-address {
              type inet:ipv6-address;
              description
                "IPv6 addresses of the customer's DHCP server.";
            }
          }
        }
      }
      case static-addresses {
        description
          "Lists the IPv4 addresses that are used.";
        list address {
          key "address-id";
          ordered-by user;
          description
            "Lists the IPv6 addresses that are used. The first
             address of the list is the primary address of
             the connection.";
          leaf address-id {
            type string;
            description
              "An identifier of the static IPv4 address.";
          }
          leaf customer-address {
            type inet:ipv6-address;
            description
              "An IPv6 address of the customer side.";
          }
        }
      }
    }
  }

  grouping ip-connection {
    description
      "Defines IP connection parameters.";
    leaf l3-termination-point {
      type string;
      description
        "Specifies a reference to a local Layer 3 termination point,
         such as a bridge domain interface.";
    }
    container ipv4 {
      if-feature "vpn-common:ipv4";
      description
        "IPv4-specific parameters.";
      uses ipv4-connection;
    }
    container ipv6 {
      if-feature "vpn-common:ipv6";
      description
        "IPv6-specific parameters.";
      uses ipv6-connection;
    }
  }

  /* Routing */
  //BGP base parameters

  grouping bgp-base {
    description
      "Configuration specific to BGP.";
    leaf description {
      type string;
      description
        "Includes a description of the BGP session. This description
         is meant to be used for diagnostic purposes. The semantic
         of the description is local to an implementation.";
    }
    leaf local-as {
      type inet:as-number;
      description
        "Indicates a local AS Number (ASN), if an ASN distinct from
         the ASN configured at the AC level is needed.";
    }
    leaf peer-as {
      type inet:as-number;
      mandatory true;
      description
        "Indicates the customer's ASN when the customer requests BGP
         routing.";
    }
    leaf address-family {
      type identityref {
        base vpn-common:address-family;
      }
      description
        "This node contains the address families to be activated.
         'dual-stack' means that both IPv4 and IPv6 will be
         activated.";
    }
    leaf multihop {
      type uint8;
      description
        "Describes the number of IP hops allowed between a given BGP
         neighbor and the PE.";
    }
    leaf as-override {
      type boolean;
      default "false";
      description
        "Defines whether ASN override is enabled, i.e., replacing the
         ASN of the customer specified in the AS_PATH attribute with
         the local ASN.";
    }
    leaf allow-own-as {
      type uint8;
      default "0";
      description
        "If set, specifies the maximum number of occurrences of the
         provider's ASN that are permitted within the AS_PATH
         before it is rejected.";
    }
    leaf prepend-global-as {
      type boolean;
      default "false";
      description
        "In some situations, the ASN that is provided at the node
         level may be distinct from the ASN configured at the AC.
         When such ASNs are provided, they are both prepended to the
         BGP route updates for this AC. To disable that behavior,
         'prepend-global-as' must be set to 'false'.  In such a
         case, the ASN that is provided at the node level is not
         prepended to the BGP route updates for this access.";
    }
    leaf send-default-route {
      type boolean;
      default "false";
      description
        "Defines whether default routes can be advertised to a peer.
         If set, the default routes are advertised to a peer.";
    }
    leaf site-of-origin {
      when "../address-family = 'vpn-common:ipv4' "
         + "or 'vpn-common:dual-stack'" {
        description
          "Only applies if IPv4 is activated.";
      }
      type rt-types:route-origin;
      description
        "The Site of Origin attribute is encoded as a Route Origin
         Extended Community. It is meant to uniquely identify the
         set of routes learned from a site via a particular AC and
         is used to prevent routing loops.";
      reference
        "RFC 4364: BGP/MPLS IP Virtual Private Networks (VPNs),
                   Section 7";
    }
    leaf ipv6-site-of-origin {
      when "../address-family = 'vpn-common:ipv6' "
         + "or 'vpn-common:dual-stack'" {
        description
          "Only applies if IPv6 is activated.";
      }
      type rt-types:ipv6-route-origin;
      description
        "The IPv6 Site of Origin attribute is encoded as an IPv6
         Route Origin Extended Community.  It is meant to uniquely
         identify the set of routes learned from a site.";
      reference
        "RFC 5701: IPv6 Address Specific BGP Extended Community
                   Attribute";
    }
    list redistribute-connected {
      key "address-family";
      description
        "Indicates, per address family, the policy to follow for
         connected routes.";
      leaf address-family {
        type identityref {
          base vpn-common:address-family;
        }
        description
          "Indicates the address family.";
      }
      leaf enable {
        type boolean;
        description
          "Enables the redistribution of connected routes.";
      }
    }
    container bgp-max-prefix {
      description
        "Controls the behavior when a prefix maximum is reached.";
      leaf max-prefix {
        type uint32;
        default "5000";
        description
          "Indicates the maximum number of BGP prefixes allowed in
           the BGP session.

           It allows control of how many prefixes can be received
           from a neighbor.

           If the limit is exceeded, the action indicated in
           'violate-action' will be followed.";
        reference
          "RFC 4271: A Border Gateway Protocol 4 (BGP-4),
                     Section 8.2.2";
      }
      leaf warning-threshold {
        type decimal64 {
          fraction-digits 5;
          range "0..100";
        }
        units "percent";
        default "75";
        description
          "When this value is reached, a warning notification will be
           triggered.";
      }
      leaf violate-action {
        type enumeration {
          enum warning {
            description
              "Only a warning message is sent to the peer when the
               limit is exceeded.";
          }
          enum discard-extra-paths {
            description
              "Discards extra paths when the limit is exceeded.";
          }
          enum restart {
            description
              "The BGP session restarts after the indicated time
               interval.";
          }
        }
        description
          "If the BGP neighbor 'max-prefix' limit is reached, the
           action indicated in 'violate-action' will be followed.";
      }
      leaf restart-timer {
        type uint32;
        units "seconds";
        description
          "Time interval after which the BGP session will be
           reestablished.";
      }
    }
    container bgp-timers {
      description
        "Includes two BGP timers.";
      leaf keepalive {
        type uint16 {
          range "0..21845";
        }
        units "seconds";
        default "30";
        description
          "This timer indicates the KEEPALIVE messages' frequency
           between a PE and a BGP peer.

           If set to '0', it indicates that KEEPALIVE messages are
           disabled.

           It is suggested that the maximum time between KEEPALIVE
           messages be one-third of the Hold Time interval.";
        reference
          "RFC 4271: A Border Gateway Protocol 4 (BGP-4),
                     Section 4.4";
      }
      leaf hold-time {
        type uint16 {
          range "0 | 3..65535";
        }
        units "seconds";
        default "90";
        description
          "Indicates the maximum number of seconds that may elapse
           between the receipt of successive KEEPALIVE and/or UPDATE
           messages from the peer.

           The Hold Time must be either zero or at least three
           seconds.";
        reference
          "RFC 4271: A Border Gateway Protocol 4 (BGP-4),
                     Section 4.2";
      }
    }
  }

  // RIP base parameters

  grouping rip-base {
    description
      "Configuration specific to RIP routing.";
    leaf address-family {
      type identityref {
        base vpn-common:address-family;
      }
      description
        "Indicates whether IPv4, IPv6, or both address families are
         to be activated.";
    }
    container timers {
      description
        "Indicates the RIP timers.";
      reference
        "RFC 2453: RIP Version 2";
      leaf update-interval {
        type uint16 {
          range "1..32767";
        }
        units "seconds";
        description
          "Indicates the RIP update time, i.e., the amount of time
           for which RIP updates are sent.";
      }
      leaf invalid-interval {
        type uint16 {
          range "1..32767";
        }
        units "seconds";
        description
          "The interval before a route is declared invalid after no
           updates are received. This value is at least three times
           the value for the 'update-interval' argument.";
      }
      leaf holddown-interval {
        type uint16 {
          range "1..32767";
        }
        units "seconds";
        description
          "Specifies the interval before better routes are
           released.";
      }
      leaf flush-interval {
        type uint16 {
          range "1..32767";
        }
        units "seconds";
        description
          "Indicates the RIP flush timer, i.e., the amount of time
           that must elapse before a route is removed from the
           routing table.";
      }
    }
    leaf default-metric {
      type uint8 {
        range "0..16";
      }
      description
        "Sets the default metric.";
    }
  }

  // routing profile

  grouping routing-profile {
    description
      "Defines routing protocols.";
    list routing-protocol {
      key "id";
      description
        "List of routing protocols used on the AC.";
      leaf id {
        type string;
        description
          "Unique identifier for the routing protocol.";
      }
      leaf type {
        type identityref {
          base vpn-common:routing-protocol-type;
        }
        description
          "Type of routing protocol.";
      }
      container bgp {
        when "derived-from-or-self(../type, "
           + "'vpn-common:bgp-routing')" {
          description
            "Only applies when the protocol is BGP.";
        }
        description
          "Configuration specific to BGP.";
        uses bgp-base;
      }
      container ospf {
        when "derived-from-or-self(../type, "
           + "'vpn-common:ospf-routing')" {
          description
            "Only applies when the protocol is OSPF.";
        }
        description
          "Configuration specific to OSPF.";
        uses ac-common:ospf-basic;
        leaf max-lsa {
          type uint32 {
            range "1..4294967294";
          }
          description
            "Maximum number of allowed Link State Advertisements
             (LSAs) that the OSPF instance will accept.";
        }
      }
      container isis {
        when "derived-from-or-self(../type, "
           + "'vpn-common:isis-routing')" {
          description
            "Only applies when the protocol is IS-IS.";
        }
        description
          "Configuration specific to IS-IS.";
        uses ac-common:isis-basic;
        leaf level {
          type identityref {
            base vpn-common:isis-level;
          }
          description
            "Can be 'level-1', 'level-2', or 'level-1-2'.";
          reference
            "RFC 9181: A Common YANG Data Model for Layer 2
                       and Layer 3 VPNs";
        }
        leaf metric {
          type uint16;
          description
            "Metric of the AC. It is used in the routing state
             calculation and path selection.";
        }
        leaf mode {
          type enumeration {
            enum active {
              description
                "The interface sends or receives IS-IS protocol
                 control packets.";
            }
            enum passive {
              description
                "Suppresses the sending of IS-IS updates through the
                 specified interface.";
            }
          }
          description
            "IS-IS interface mode type.";
        }
      }
      container rip {
        when "derived-from-or-self(../type, "
           + "'vpn-common:rip-routing')" {
          description
            "Only applies when the protocol is RIP.";
        }
        description
          "Configuration specific to RIP routing.";
        uses rip-base;
      }
      container vrrp {
        when "derived-from-or-self(../type, "
           + "'vpn-common:vrrp-routing')" {
          description
            "Only applies when the protocol is the Virtual Router
             Redundancy Protocol (VRRP).";
        }
        description
          "Configuration specific to VRRP.";
        reference
          "RFC 5798: Virtual Router Redundancy Protocol (VRRP)
                     Version 3 for IPv4 and IPv6";
        leaf address-family {
          type identityref {
            base vpn-common:address-family;
          }
          description
            "Indicates whether IPv4, IPv6, or both address families
             are to be enabled.";
        }
        leaf ping-reply {
          type boolean;
          description
            "Controls whether the VRRP speaker should reply to ping
             requests.";
        }
      }
    }
  }

  grouping routing {
    description
      "Defines routing protocols.";
    list routing-protocol {
      key "id";
      description
        "List of routing protocols used on the AC.";
      leaf id {
        type string;
        description
          "Unique identifier for the routing protocol.";
      }
      leaf type {
        type identityref {
          base vpn-common:routing-protocol-type;
        }
        description
          "Type of routing protocol.";
      }
      list routing-profiles {
        key "id";
        description
          "Routing profiles.";
        leaf id {
          type leafref {
            path "/nw:networks/nw:network"
               + "/ac-ntw:specific-provisioning-profiles"
               + "/valid-provider-identifiers"
               + "/routing-profile-identifier/id";
          }
          description
            "Routing profile to be used.";
        }
        leaf type {
          type identityref {
            base vpn-common:ie-type;
          }
          description
            "Import, export, or both.";
        }
      }
      container static {
        when "derived-from-or-self(../type, "
           + "'vpn-common:static-routing')" {
          description
            "Only applies when the protocol is a static routing
             protocol.";
        }
        description
          "Configuration specific to static routing.";
        container cascaded-lan-prefixes {
          description
            "LAN prefixes from the customer.";
          list ipv4-lan-prefixes {
            if-feature "vpn-common:ipv4";
            key "lan next-hop";
            description
              "List of LAN prefixes for the site.";
            uses ac-common:ipv4-static-rtg-entry;
            leaf bfd-enable {
              if-feature "vpn-common:bfd";
              type boolean;
              description
                "Enables BFD.";
            }
            leaf preference {
              type uint32;
              description
                "Indicates the preference associated with the static
                 route.";
            }
            uses vpn-common:service-status;
          }
          list ipv6-lan-prefixes {
            if-feature "vpn-common:ipv6";
            key "lan next-hop";
            description
              "List of LAN prefixes for the site.";
            uses ac-common:ipv4-static-rtg-entry;
            leaf bfd-enable {
              if-feature "vpn-common:bfd";
              type boolean;
              description
                "Enables BFD.";
            }
            leaf preference {
              type uint32;
              description
                "Indicates the preference associated with the static
                 route.";
            }
            uses vpn-common:service-status;
          }
        }
      }
      container bgp {
        when "derived-from-or-self(../type, "
           + "'vpn-common:bgp-routing')" {
          description
            "Only applies when the protocol is BGP.";
        }
        description
          "Configuration specific to BGP.";
        container peer-groups {
          description
            "Configuration for BGP peer-groups";
          list peer-group {
            key "name";
            description
              "List of BGP peer-groups configured on the local
               system - uniquely identified by peer-group name";
            leaf name {
              type string;
              description
                "Name of the BGP peer-group";
            }
            leaf local-address {
              type union {
                type inet:ip-address;
                type if:interface-ref;
              }
              description
                "Sets the local IP address to use for the BGP
                 transport session. This may be expressed as either
                 an IP address or a reference to an interface.";
            }
            uses bgp-base;
            uses ac-common:bgp-authentication;
          }
        }
        list neighbor {
          key "remote-address";
          description
            "List of BGP neighbors.";
          leaf remote-address {
            type inet:ip-address;
            description
              "The remote IP address of this entry's BGP peer.";
          }
          leaf local-address {
            type union {
              type inet:ip-address;
              type if:interface-ref;
            }
            description
              "Sets the local IP address to use for
               the BGP transport session.  This may be
               expressed as either an IP address or a
               reference to an interface.";
          }
          leaf peer-group {
            type leafref {
              path "../../peer-groups/peer-group/name";
            }
            description
              "The peer-group with which this neighbor is
               associated.";
          }
          uses bgp-base;
          uses ac-common:bgp-authentication;
          uses vpn-common:service-status;
        }
      }
      container ospf {
        when "derived-from-or-self(../type, "
           + "'vpn-common:ospf-routing')" {
          description
            "Only applies when the protocol is OSPF.";
        }
        description
          "Configuration specific to OSPF.";
        uses ac-common:ospf-basic;
        container sham-links {
          if-feature "vpn-common:rtg-ospf-sham-link";
          description
            "List of sham links.";
          reference
            "RFC 4577: OSPF as the Provider/Customer Edge Protocol
                       for BGP/MPLS IP Virtual Private Networks
                       (VPNs), Section 4.2.7
             RFC 6565: OSPFv3 as a Provider Edge to Customer Edge
                       (PE-CE) Routing Protocol, Section 5";
          list sham-link {
            key "target-site";
            description
              "Creates a sham link with another
               site.";
            leaf target-site {
              type string;
              description
                "Target site for the sham link connection. The site
                 is referred to by its identifier.";
            }
            leaf metric {
              type uint16;
              default "1";
              description
                "Metric of the sham link. It is used in the routing
                 state calculation and path selection.";
              reference
                "RFC 4577: OSPF as the Provider/Customer Edge
                           Protocol for BGP/MPLS IP Virtual Private
                           Networks (VPNs), Section 4.2.7.3
                 RFC 6565: OSPFv3 as a Provider Edge to Customer Edge
                           (PE-CE) Routing Protocol, Section 5.2";
            }
          }
        }
        leaf max-lsa {
          type uint32 {
            range "1..4294967294";
          }
          description
            "Maximum number of allowed Link State Advertisements
             (LSAs) that the OSPF instance will accept.";
        }
        uses ac-common:ospf-authentication;
        uses vpn-common:service-status;
      }
      container isis {
        when "derived-from-or-self(../type, "
           + "'vpn-common:isis-routing')" {
          description
            "Only applies when the protocol is
             IS-IS.";
        }
        description
          "Configuration specific to IS-IS.";
        uses ac-common:isis-basic;
        leaf level {
          type identityref {
            base vpn-common:isis-level;
          }
          description
            "Can be 'level-1', 'level-2', or 'level-1-2'.";
          reference
            "RFC 9181: A Common YANG Data Model for Layer 2 and
                       Layer 3 VPNs";
        }
        leaf metric {
          type uint16;
          default "1";
          description
            "Metric of the PE-CE link. It is used in the routing
             state calculation and path selection.";
        }
        leaf mode {
          type enumeration {
            enum active {
              description
                "The interface sends or receives
                 IS-IS protocol control packets.";
            }
            enum passive {
              description
                "Suppresses the sending of IS-IS
                 updates through the specified
                 interface.";
            }
          }
          default "active";
          description
            "IS-IS interface mode type.";
        }
        uses ac-common:isis-authentication;
        uses vpn-common:service-status;
      }
      container rip {
        when "derived-from-or-self(../type, "
           + "'vpn-common:rip-routing')" {
          description
            "Only applies when the protocol is RIP.
             For IPv4, the model assumes that RIP
             version 2 is used.";
        }
        description
          "Configuration specific to RIP routing.";
        uses rip-base;
        uses ac-common:rip-authentication;
        uses vpn-common:service-status;
      }
      container vrrp {
        when "derived-from-or-self(../type, "
           + "'vpn-common:vrrp-routing')" {
          description
            "Only applies when the protocol is the VRRP.";
        }
        description
          "Configuration specific to VRRP.";
        reference
          "RFC 5798: Virtual Router Redundancy Protocol (VRRP)
                     Version 3 for IPv4 and IPv6";
        leaf address-family {
          type identityref {
            base vpn-common:address-family;
          }
          description
            "Indicates whether IPv4, IPv6, or both address families
             are to be enabled.";
        }
        leaf vrrp-group {
          type uint8 {
            range "1..255";
          }
          description
            "Includes the VRRP group identifier.";
        }
        leaf backup-peer {
          type inet:ip-address;
          description
            "Indicates the IP address of the peer.";
        }
        leaf-list virtual-ip-address {
          type inet:ip-address;
          description
            "Virtual IP addresses for a single VRRP
             group.";
          reference
            "RFC 5798: Virtual Router Redundancy Protocol (VRRP)
                       Version 3 for IPv4 and IPv6, Sections 1.2
                       and 1.3";
        }
        leaf priority {
          type uint8 {
            range "1..254";
          }
          default "100";
          description
            "Sets the local priority of the VRRP speaker.";
        }
        leaf ping-reply {
          type boolean;
          default "false";
          description
            "Controls whether the VRRP speaker should reply to ping
             requests.";
        }
        uses vpn-common:service-status;
      }
    }
  }

  // OAM

  grouping bfd {
    description
      "Grouping for BFD.";
    leaf session-type {
      type identityref {
        base vpn-common:bfd-session-type;
      }
      default "vpn-common:classic-bfd";
      description
        "Specifies the BFD session type.";
    }
    leaf desired-min-tx-interval {
      type uint32;
      units "microseconds";
      default "1000000";
      description
        "The minimum interval between transmissions of BFD Control
         packets, as desired by the operator.";
      reference
        "RFC 5880: Bidirectional Forwarding Detection (BFD),
                   Section 6.8.7";
    }
    leaf required-min-rx-interval {
      type uint32;
      units "microseconds";
      default "1000000";
      description
        "The minimum interval between received BFD Control packets
         that the PE should support.";
      reference
        "RFC 5880: Bidirectional Forwarding Detection (BFD),
                   Section 6.8.7";
    }
    leaf local-multiplier {
      type uint8 {
        range "1..255";
      }
      default "3";
      description
        "Specifies the detection multiplier that is transmitted to a
         BFD peer.

         The detection interval for the receiving BFD peer is
         calculated by multiplying the value of the negotiated
         transmission interval by the received detection multiplier
         value.";
      reference
        "RFC 5880: Bidirectional Forwarding Detection (BFD),
                   Section 6.8.7";
    }
    leaf holdtime {
      type uint32;
      units "milliseconds";
      description
        "Expected BFD holdtime.

         The customer may impose some fixed values for the holdtime
         period if the provider allows the customer to use this
         function.";
      reference
        "RFC 5880: Bidirectional Forwarding Detection (BFD),
                   Section 6.8.18";
    }
  }

  // OAM

  grouping oam {
    description
      "Defines the Operations, Administration, and Maintenance
       (OAM) mechanisms used.";
    container bfd {
      description
        "Container for BFD.";
      leaf profile {
        type leafref {
          path "/nw:networks/nw:network"
             + "/ac-ntw:specific-provisioning-profiles"
             + "/valid-provider-identifiers"
             + "/bfd-profile-identifier/id";
        }
        description
          "Well-known service provider profile name.";
      }
      uses bfd;
      container authentication {
        presence "Enables BFD authentication";
        description
          "Parameters for BFD authentication.";
        leaf key-chain {
          type key-chain:key-chain-ref;
          description
            "Name of the key chain.";
        }
        leaf meticulous {
          type boolean;
          description
            "Enables meticulous mode.";
          reference
            "RFC 5880: Bidirectional Forwarding Detection (BFD),
                       Section 6.7";
        }
      }
      uses vpn-common:service-status;
    }
  }

  // security

  grouping security {
    description
      "Security parameters for an AC.";
    container encryption {
      if-feature "vpn-common:encryption";
      description
        "Container for AC encryption.";
      leaf enabled {
        type boolean;
        default "false";
        description
          "If set to 'true', traffic encryption on the connection is
           required. Otherwise, it is disabled.";
      }
      leaf layer {
        when "../enabled = 'true'" {
          description
            "Included only when encryption is enabled.";
        }
        type enumeration {
          enum layer2 {
            description
              "Encryption occurs at Layer 2.";
          }
          enum layer3 {
            description
              "Encryption occurs at Layer 3. For example, IPsec
               may be used when a customer requests Layer 3
               encryption.";
          }
        }
        description
          "Indicates the layer on which encryption is applied.";
      }
    }
    container encryption-profile {
      when "../encryption/enabled = 'true'" {
        description
          "Indicates the layer on which encryption is enabled.";
      }
      description
        "Container for the encryption profile.";
      choice profile {
        description
          "Choice for the encryption profile.";
        case provider-profile {
          leaf profile-name {
            type leafref {
              path "/nw:networks/nw:network"
                 + "/ac-ntw:specific-provisioning-profiles"
                 + "/valid-provider-identifiers"
                 + "/encryption-profile-identifier/id";
            }
            description
              "Name of the provider's profile to be applied.";
          }
        }
        case customer-profile {
          leaf customer-key-chain {
            type key-chain:key-chain-ref;
            description
              "Customer-supplied key chain.";
          }
        }
      }
    }
  }

  // AC profile

  grouping ac-profile {
    description
      "Grouping for attachment circuit profiles.";
    container l2-connection {
      description
        "Defines Layer 2 protocols and parameters that
         are required to enable AC connectivity.";
      //uses l2-connection;
    }
    container ip-connection {
      description
        "Defines IP connection parameters.";
      //uses l3-connection;
    }
    container routing-protocols {
      description
        "Defines routing protocols.";
      uses routing-profile;
    }
    container oam {
      description
        "Defines the OAM mechanisms used for the AC profile.";
      container bfd {
        if-feature "vpn-common:bfd";
        description
          "Container for BFD.";
        uses bfd;
      }
    }
  }

  //AC network provisioning

  grouping ac {
    description
      "Grouping for attachment circuits.";
    leaf description {
      type string;
      description
        "Associates a description with an AC.";
    }
    container l2-connection {
      description
        "Defines Layer 2 protocols and parameters that are required
         to enable AC connectivity.";
      uses l2-connection-if-ref;
    }
    container ip-connection {
      description
        "Defines IP connection parameters.";
      uses ip-connection;
    }
    container routing-protocols {
      description
        "Defines routing protocols.";
      uses routing;
    }
    container oam {
      description
        "Defines the OAM mechanisms used for the AC.";
      uses oam;
    }
    container security {
      description
        "AC-specific security parameters.";
      uses security;
    }
  }

  augment "/nw:networks/nw:network" {
    description
      "Add a list of profiles.";
    container specific-provisioning-profiles {
      description
        "Contains a set of valid profiles to reference in the AC
         activation.";
      uses vpn-common:vpn-profile-cfg;
    }
    list ac-profile {
      key "name";
      description
        "Specifies a list of AC profiles.";
      leaf name {
        type string;
        description
          "Name of the AC.";
      }
      uses ac-ntw:ac-profile;
    }
  }

  augment "/nw:networks/nw:network/nw:node"
        + "/sap:service/sap:sap" {
    when '../../../nw:network-types/sap:sap-network' {
      description
        "Augmentation parameters apply only for SAP networks.";
    }
    description
      "Augments SAPs with AC provisioning details.";
    list ac {
      key "name";
      description
        "List of ACs.";
      leaf name {
        type string;
        description
          "A local AC identifier.";
      }
      leaf ac-ref {
        type ac-svc:attachment-circuit-reference;
        description
          "A reference to the AC as exposed at the service level.";
      }
      list ac-profile {
        key "profile-id";
        description
          "List of AC profiles.";
        leaf profile-id {
          type leafref {
            path "/nw:networks/nw:network/ac-profile/name";
          }
          description
            "A reference to an AC profile.";
        }
      }
      leaf-list peer-sap-id {
        type string;
        description
          "One or more peer SAPs can be indicated.";
      }
      list group {
        key "group-id";
        description
          "List of group-ids.";
        leaf group-id {
          type string;
          description
            "Indicates the group-id to which the AC belongs.";
        }
        leaf precedence {
          type identityref {
            base ac-common:precedence-type;
          }
          description
            "Defines redundancy of an AC.";
        }
      }
      uses vpn-common:service-status;
      uses ac-ntw:ac;
    }
  }
}

<CODE ENDS>

6. Security Considerations

The YANG module specified in this document defines a schema for data that is designed to be accessed via network management protocols such as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer is the secure transport layer, and the mandatory-to-implement secure transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer is HTTPS, and the mandatory-to-implement secure transport is TLS [RFC8446].

The Network Configuration Access Control Model (NACM) [RFC8341] provides the means to restrict access for particular NETCONF or RESTCONF users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content.

There are a number of data nodes defined in this YANG module that are writable/creatable/deletable (i.e., config true, which is the default). These data nodes may be considered sensitive or vulnerable in some network environments. Write operations (e.g., edit-config) and delete operations to these data nodes without proper protection or authentication can have a negative effect on network operations. These are the subtrees and data nodes and their sensitivity/ vulnerability in the "ietf-ac-ntw" module:

Some of the readable data nodes in this YANG module may be considered sensitive or vulnerable in some network environments. It is thus important to control read access (e.g., via get, get-config, or notification) to these data nodes. These are the subtrees and data nodes and their sensitivity/vulnerability in the "ietf-ac-svc" module:

Several data nodes ('bgp', 'ospf', 'isis', and 'rip') rely upon [RFC8177] for authentication purposes. As such, the AC network module inherits the security considerations discussed in Section 5 of [RFC8177]. Also, these data nodes support supplying explicit keys as strings in ASCII format. The use of keys in hexadecimal string format would afford greater key entropy with the same number of key-string octets. However, such a format is not included in this version of the AC network model, because it is not supported by the underlying device modules (e.g., [RFC8695]).

7. IANA Considerations

IANA is requested to register the following URI in the "ns" subregistry within the "IETF XML Registry" [RFC3688]:

   URI:  urn:ietf:params:xml:ns:yang:ietf-ac-ntw
   Registrant Contact:  The IESG.
   XML:  N/A; the requested URI is an XML namespace.

IANA is requested to register the following YANG module in the "YANG Module Names" subregistry [RFC6020] within the "YANG Parameters" registry.

   Name:  ietf-ac-ntw
   Maintained by IANA?  N
   Namespace:  urn:ietf:params:xml:ns:yang:ietf-ac-ntw
   Prefix:  ac-ntw
   Reference:  RFC xxxx

8. References

8.1. Normative References

[I-D.boro-opsawg-teas-attachment-circuit]
Boucadair, M., Roberts, R., de Dios, O. G., Barguil, S., and B. Wu, "YANG Data Models for 'Attachment Circuits'-as-a-Service (ACaaS)", Work in Progress, Internet-Draft, draft-boro-opsawg-teas-attachment-circuit-04, , <https://datatracker.ietf.org/doc/html/draft-boro-opsawg-teas-attachment-circuit-04>.
[I-D.boro-opsawg-teas-common-ac]
Boucadair, M., Roberts, R., de Dios, O. G., Barguil, S., and B. Wu, "A Common YANG Data Model for Attachment Circuits", Work in Progress, Internet-Draft, draft-boro-opsawg-teas-common-ac-01, , <https://datatracker.ietf.org/doc/html/draft-boro-opsawg-teas-common-ac-01>.
[I-D.ietf-opsawg-sap]
Boucadair, M., de Dios, O. G., Barguil, S., Wu, Q., and V. Lopez, "A YANG Network Model for Service Attachment Points (SAPs)", Work in Progress, Internet-Draft, draft-ietf-opsawg-sap-15, , <https://datatracker.ietf.org/doc/html/draft-ietf-opsawg-sap-15>.
[RFC2119]
Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, , <https://www.rfc-editor.org/rfc/rfc2119>.
[RFC3688]
Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, DOI 10.17487/RFC3688, , <https://www.rfc-editor.org/rfc/rfc3688>.
[RFC6020]
Bjorklund, M., Ed., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, , <https://www.rfc-editor.org/rfc/rfc6020>.
[RFC6241]
Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed., and A. Bierman, Ed., "Network Configuration Protocol (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, , <https://www.rfc-editor.org/rfc/rfc6241>.
[RFC6242]
Wasserman, M., "Using the NETCONF Protocol over Secure Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, , <https://www.rfc-editor.org/rfc/rfc6242>.
[RFC6991]
Schoenwaelder, J., Ed., "Common YANG Data Types", RFC 6991, DOI 10.17487/RFC6991, , <https://www.rfc-editor.org/rfc/rfc6991>.
[RFC8040]
Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF Protocol", RFC 8040, DOI 10.17487/RFC8040, , <https://www.rfc-editor.org/rfc/rfc8040>.
[RFC8174]
Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, , <https://www.rfc-editor.org/rfc/rfc8174>.
[RFC8177]
Lindem, A., Ed., Qu, Y., Yeung, D., Chen, I., and J. Zhang, "YANG Data Model for Key Chains", RFC 8177, DOI 10.17487/RFC8177, , <https://www.rfc-editor.org/rfc/rfc8177>.
[RFC8294]
Liu, X., Qu, Y., Lindem, A., Hopps, C., and L. Berger, "Common YANG Data Types for the Routing Area", RFC 8294, DOI 10.17487/RFC8294, , <https://www.rfc-editor.org/rfc/rfc8294>.
[RFC8341]
Bierman, A. and M. Bjorklund, "Network Configuration Access Control Model", STD 91, RFC 8341, DOI 10.17487/RFC8341, , <https://www.rfc-editor.org/rfc/rfc8341>.
[RFC8342]
Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K., and R. Wilton, "Network Management Datastore Architecture (NMDA)", RFC 8342, DOI 10.17487/RFC8342, , <https://www.rfc-editor.org/rfc/rfc8342>.
[RFC8343]
Bjorklund, M., "A YANG Data Model for Interface Management", RFC 8343, DOI 10.17487/RFC8343, , <https://www.rfc-editor.org/rfc/rfc8343>.
[RFC8446]
Rescorla, E., "The Transport Layer Security (TLS) Protocol Version 1.3", RFC 8446, DOI 10.17487/RFC8446, , <https://www.rfc-editor.org/rfc/rfc8446>.
[RFC9181]
Barguil, S., Gonzalez de Dios, O., Ed., Boucadair, M., Ed., and Q. Wu, "A Common YANG Data Model for Layer 2 and Layer 3 VPNs", RFC 9181, DOI 10.17487/RFC9181, , <https://www.rfc-editor.org/rfc/rfc9181>.
[RFC9182]
Barguil, S., Gonzalez de Dios, O., Ed., Boucadair, M., Ed., Munoz, L., and A. Aguado, "A YANG Network Data Model for Layer 3 VPNs", RFC 9182, DOI 10.17487/RFC9182, , <https://www.rfc-editor.org/rfc/rfc9182>.
[RFC9291]
Boucadair, M., Ed., Gonzalez de Dios, O., Ed., Barguil, S., and L. Munoz, "A YANG Network Data Model for Layer 2 VPNs", RFC 9291, DOI 10.17487/RFC9291, , <https://www.rfc-editor.org/rfc/rfc9291>.

8.2. Informative References

[AC-Ntw-Tree]
"Full Network Attachment Circuit Tree Structure", , <https://github.com/boucadair/network-attachment-circuits/blob/main/yang/ac-ntw-without-groupings.txt>.
[RFC8340]
Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams", BCP 215, RFC 8340, DOI 10.17487/RFC8340, , <https://www.rfc-editor.org/rfc/rfc8340>.
[RFC8695]
Liu, X., Sarda, P., and V. Choudhary, "A YANG Data Model for the Routing Information Protocol (RIP)", RFC 8695, DOI 10.17487/RFC8695, , <https://www.rfc-editor.org/rfc/rfc8695>.
[RFC8969]
Wu, Q., Ed., Boucadair, M., Ed., Lopez, D., Xie, C., and L. Geng, "A Framework for Automating Service and Network Management with YANG", RFC 8969, DOI 10.17487/RFC8969, , <https://www.rfc-editor.org/rfc/rfc8969>.

Acknowledgments

Thanks to Moti Morgenstern for the review and comments.

Authors' Addresses

Mohamed Boucadair (editor)
Orange
Richard Roberts
Juniper
Oscar Gonzalez de Dios
Telefonica
Samier Barguil Giraldo
Nokia
Bo Wu
Huawei Technologies