Softwire Y. Cui Internet-Draft J. Dong Intended status: Standards Track P. Wu Expires: September 13, 2012 M. Xu Tsinghua University March 12, 2012 Softwire Mesh Management Information Base(MIB) draft-cui-softwire-mesh-mib-04 Abstract This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular it defines objects for managing softwire mesh [RFC5565]. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on September 13, 2012. Copyright Notice Copyright (c) 2012 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as Cui, et al. Expires September 13, 2012 [Page 1] Internet-Draft swmMIB March 2012 described in the Simplified BSD License. This document may contain material from IETF Documents or IETF Contributions published or made publicly available before November 10, 2008. The person(s) controlling the copyright in some of this material may not have granted the IETF Trust the right to allow modifications of such material outside the IETF Standards Process. Without obtaining an adequate license from the person(s) controlling the copyright in such materials, this document may not be modified outside the IETF Standards Process, and derivative works of it may not be created outside the IETF Standards Process, except to format it for publication as an RFC or to translate it into languages other than English. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. The Internet-Standard Management Framework . . . . . . . . . . 3 3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3 4. Conventions . . . . . . . . . . . . . . . . . . . . . . . . . 3 5. Structure of the MIB Module . . . . . . . . . . . . . . . . . 3 5.1. The swmSupportedTunnlTable Subtree . . . . . . . . . . . . 3 5.2. The swmEncapsTable Subtree . . . . . . . . . . . . . . . . 4 5.3. The swmBGPNeighborTable Subtree . . . . . . . . . . . . . 4 5.4. The swmMIBConformance Subtree . . . . . . . . . . . . . . 4 6. Relationship to Other MIB Modules . . . . . . . . . . . . . . 4 6.1. Relationship to the IF-MIB . . . . . . . . . . . . . . . . 4 6.2. Relationship to the IP Tunnel MIB . . . . . . . . . . . . 5 6.3. MIB modules required for IMPORTS . . . . . . . . . . . . . 5 7. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 5 8. Security Considerations . . . . . . . . . . . . . . . . . . . 11 9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 11 10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 12 10.1. Normative References . . . . . . . . . . . . . . . . . . . 12 10.2. Informative References . . . . . . . . . . . . . . . . . . 12 10.3. URL References . . . . . . . . . . . . . . . . . . . . . . 13 Cui, et al. Expires September 13, 2012 [Page 2] Internet-Draft swmMIB March 2012 1. Introduction Softwire mesh framework RFC 5565 [RFC5565]is a tunneling mechanism which enables connectivity between islands of IPv4, IPv6 or dual- stack networks across single IPv4 or IPv6 backbone networks. In softwire mesh solution, extended multiprotocol-BGP (MP-BGP)is used to set up tunnels and advertise prefixes among address family border routers (AFBRs). This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular it defines objects for managing softwire mesh [RFC5565]. 2. The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). They are defined using the mechanisms stated in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580]. 3. Terminology This document uses terminology from softwire problem statement RFC 4925 [RFC4925] and softwire mesh framework RFC5565 [RFC5565]. 4. Conventions The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. 5. Structure of the MIB Module The softwire mesh MIB provides a method to configure and manage the softwire mesh objects through SNMP. 5.1. The swmSupportedTunnlTable Subtree Since AFBR need to negotiate with BGP peer what kind of tunnel they will use, it should firstly announce the types of tunnels it Cui, et al. Expires September 13, 2012 [Page 3] Internet-Draft swmMIB March 2012 supports. The swmSupportedTunnlTable subtree provides the information. According to section 4 of RFC 5512[RFC5512], current softwire mesh tunnel types include IP-IP, GRE and L2TPv3. 5.2. The swmEncapsTable Subtree The swmEncapsTable subtree provides softwire mesh NLRI-NH information about the AFBR. It indicates which I-IP destination address will be encapsulated according to the arriving packet's E-IP destination address. The definitions of E-IP and I-IP are explained in section 4.1 of RFC 5565[RFC5565]. 5.3. The swmBGPNeighborTable Subtree The subtree provides softwire mesh BGP neighbor information about the AFBR. It includes the address of softwire mesh BGP peer, and the kind of tunnel that the AFBR would use to communicate with this BGP peer. 5.4. The swmMIBConformance Subtree The subtree provides conformance information of MIB objects. 6. Relationship to Other MIB Modules 6.1. Relationship to the IF-MIB The Interfaces MIB [RFC2863] defines generic managed objects for managing interfaces. Each logical interface (physical or virtual) has an ifEntry. Tunnels are handled by creating a logical interface (ifEntry) for each tunnel. Softwire mesh tunnel also acts as a virtual interface, which has corresponding entries in IP Tunnel MIB and Interface MIB. Those corresponding entries are indexed by ifIndex. The ifOperStatus in ifTable would be used to represent whether the mesh function of the AFBR has been started. During the BGP OPEN phase, if the softwire mesh capability is negotiated, the mesh function could be considered to be started, and ifOperStatus is "up". Otherwise the ifOperStatus is "down". If it is IPv4-over-IPv6 softwire mesh tunnel, the ifInUcastPkts will represent the number of IPv6 packets which can be decapsulated to IPv4 in the virtual interface. The ifOutUcastPkts contains the number of IPv6 packets which have been encapsulated with IPv4 packets in it. Particularly, if these IPv4 packets need to be fragmented, the number counted here is the packets after fragmentation. Cui, et al. Expires September 13, 2012 [Page 4] Internet-Draft swmMIB March 2012 If it is IPv6-over-IPv4 softwire mesh tunnel, the ifInUcastPkts stands for the number of IPv4 packets which would be decapsulated to IPv6 in the virtual interface. The ifOutUcastPkts represents the number of IPv4 packets which have been encapsulated from IPv6. Particularly, if these IPv6 packets need to be fragmented, the number counted here is the packets after fragmentation. Similar definition apply to other counting objects in ifTalbe. 6.2. Relationship to the IP Tunnel MIB The IP Tunnel MIB [RFC4087] contains objects common to all IP tunnels, including softwire mesh. Additionally, tunnel encapsulation specific MIB (as is defined in this document) extends the IP tunnel MIB to further described encapsulation specific information. Since softwire mesh is a point to multi-point tunnel, we need to specify an encapsulation table to support E-IP routing among AFBRs. With the encapsulation information, the correct forwarding of E-IP packets will be performed among AFBRs by using I-IP encapsulation. Each AFBR also needs to know information about remote BGP peers (AFBRs), so that these AFBRs can negotiate E-IP information and the tunnel types they support. The implementation of the IP Tunnel MIB is required for softwire mesh. The tunnelIfEncapsMethod in the tunnelIfEntry should be set to softwireMesh("xx"), and corresponding entry in the softwire mesh MIB module will exist for every tunnelIfEntry with this tunnelIfEncapsMethod. The tunnelIfRemoteInetAddress must be set to 0.0.0.0 for IPv4 or :: for IPv6 because it is a point to multi-point tunnel. Since tunnelIfAddressType in tunnelIfTable represents the type of address in the corresponding tunnelIfLocalInetAddress and tunnelIfRemoteInetAddress objects, we can also use the tunnelIfAddressType to specify the softwire mesh tunnel is IPv4-over- IPv6 or IPv6-over-IPv4. When tunnelIfAddressType is IPv4, the encapsulation would be IPv6- over-IPv4; When tunnelIfAddressType is IPv6, the encapsulation would be IPv4-over-IPv6. 6.3. MIB modules required for IMPORTS The following MIB module IMPORTS objects from SNMPv2-SMI [RFC2578], SNMPv2-TC [RFC2579], SNMPv2-CONF [RFC2580], IF-MIB [RFC2863] and INET-ADDRESS-MIB [RFC4001]. 7. Definitions SOFTWIRE-MESH-MIB DEFINITIONS ::= BEGIN Cui, et al. Expires September 13, 2012 [Page 5] Internet-Draft swmMIB March 2012 IMPORTS TruthValue, TEXTUAL-CONVENTION TimeStamp FROM SNMPv2-TC OBJECT-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF MODULE-IDENTITY, OBJECT-TYPE, mib-2, Unsigned32, Counter32, Counter64 FROM SNMPv2-SMI IANAtunnelType FROM IANAifType-MIB; InetAddress, InetAddressPrefixLength FROM INET-ADDRESS-MIB swmMIB MODULE-IDENTITY LAST-UPDATED "201112290000Z" -- December 29, 2011 ORGANIZATION "Softwire Working Group" CONTACT-INFO " Yong Cui Email: yong@csnet1.cs.tsinghua.edu.cn Jiang Dong Email: dongjiang@csnet1.cs.tsinghua.edu.cn Peng Wu Email: weapon@csnet1.cs.tsinghua.edu.cn Mingwei Xu Email: xmw@cernet.edu.cn Email comments directly to the softwire WG Mailing List at softwires@ietf.org " DESCRIPTION "This MIB module contains managed object definitions for the softwire mesh framework." REVISION "201203120000Z" DESCRIPTION "draft-04 version" ::= {transmission xxx} --xxx to be replaced with correct value -- swmSupportedTunnelTable Cui, et al. Expires September 13, 2012 [Page 6] Internet-Draft swmMIB March 2012 swmSupportedTunnelTable OBJECT-TYPE SYNTAX SEQUENCE OF swmSupportedTunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of objects that shows what kind of tunnels can be supported in the AFBR." ::= { swmMIB 1 } swmSupportedTunnelEntry OBJECT-TYPE SYNTAX swmSupportedTunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of objects that shows what kind of tunnels can be supported in the AFBR. If the AFBR supports several kinds of tunnel type, the swmSupportedTunnelTalbe would has several entries." INDEX { swmSupportedTunnelType } ::= { swmSupportedTunnelTable 1 } swmSupportedTunnelEntry ::= SEQUENCE { swmSupportedTunnelType IANATunnelType } swmSupportedTunnelType OBJECT-TYPE SYNTAX IANATunnelType MAX-ACCESS read-only STATUS current DESCRIPTION "Represents the kind of tunneling type that the AFBR support. " ::= { swmSupportedTunnelTypeEntry 1 } -- end of swmSupportedTunnelTable --swmEncapsTable swmEncapsTable OBJECT-TYPE SYNTAX SEQUENCE OF swmEncapsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of objects that display and control the softwire mesh encapsulation information." ::= { swmMIB 2 } swmEncapsEntry OBJECT-TYPE SYNTAX swmEncapsEntry Cui, et al. Expires September 13, 2012 [Page 7] Internet-Draft swmMIB March 2012 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of objects that display and control the softwire mesh encapsulation information." INDEX { ifIndex, swmEncapsEIPDst, swmEncapsEIPMask } ::= { swmEncapsTable 1 } swmEncapsEntry ::= SEQUENCE { swmEncapsEIPDst InetAddress, swmEncapsEIPMask InetAddressPrefixLength, swmEncapsIIPDst InetAddress } swmEncapsEIPDst OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination E-IP address that decide which I-IP address will be encapsulated. The address Type is opposite to tunnelIfAddressType in tunnelIfTable." ::= { swmEncapsEntry 1 } swmEncapsEIPMask OBJECT-TYPE SYNTAX InetAddressPrefixLength MAX-ACCESS read-only STATUS current DESCRIPTION "The prefix length of E-IP address." ::= { swmEncapsEntry 2 } swmEncapsIIPDst OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The I-IP address that will be encapsulated according to the E-IP address.The address Type is the same as tunnelIfAddressType in tunnelIfTable. Since the tunnelIfRemoteInetAddress in tunnelIfTable should be 0.0.0.0 or ::, swmEncapIIPDst is the destination address used in the outer IP header." ::= { swmEncapsEntry 3 } Cui, et al. Expires September 13, 2012 [Page 8] Internet-Draft swmMIB March 2012 -- End of swmEncapsTable -- swmBGPNeighborTable swmBGPNeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF swmBGPNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of objects that display the softwire mesh BGP neighbor information." ::= { swmMIB 3 } swmBGPNeighborEntry OBJECT-TYPE SYNTAX swmBGPNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of objects that display the softwire mesh BGP neighbor information." INDEX { ifIndex, swmBGPNeighborInetAddress } ::= { swmBGPNeighborTable 1 } swmBGPNeighborEntry ::= SEQUENCE { swmBGPNeighborInetAddress InetAddress, swmBGPNeighborTunnelType IANATunnelType } swmBGPNeighborInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address of the ABFR's BGP neighbor. The address type is the same as tunnelIfAddressType in tunnelIfTable" ::= { swmBGPNeighborEntry 1 } swmBGPNeighborTunnelType OBJECT-TYPE SYNTAX IANATunnelType MAX-ACCESS read-only STATUS current DESCRIPTION "Represents the kind of tunneling type that the AFBR used to comunication with the BGP neighbor" Cui, et al. Expires September 13, 2012 [Page 9] Internet-Draft swmMIB March 2012 ::= { swmBGPNeighborEntry 2 } -- End of swmBGPNeighborTable -- conformance information swmMIBConformance OBJECT IDENTIFIER ::= { swmMIB 4 } swmMIBCompliances OBJECT IDENTIFIER ::= { swmMIBConformance 1 } swmMIBGroups OBJECT IDENTIFIER ::= { swmMIBConformance 2 } -- compliance statements swmMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Describes the requirements for conformance to the softwire mesh MIB." MODULE -- this module MANDATORY-GROUPS { swmSupportedTunnelGroup, swmEncapsGroup, swmBGPNeighborGroup } ::= { swmMIBCompliances 1 } swmSupportedTunnelGroup OBJECT-GROUP OBJECTS { swmSupportedTunnelType } STATUS current DESCRIPTION "The collection of objects which are used to show what kind of tunnel the AFBR supports." ::= { swmMIBGroups 1 } swmEncapsGroup OBJECT-GROUP OBJECTS { swmEncapsEIPDst, swmEncapsEIPMask, swmEncapsIIPDst } STATUS current DESCRIPTION "The collection of objects which are used to display softwire mesh encapsulation information." ::= { swmMIBGroups 2 } Cui, et al. Expires September 13, 2012 [Page 10] Internet-Draft swmMIB March 2012 swmBGPNeighborGroup OBJECT-GROUP OBJECTS { swmBGPNeighborInetAddress, swmBGPNeighborTunnelType } STATUS current DESCRIPTION "The collection of objects which are used to display softwire mesh BGP neighbor information." ::= { swmMIBGroups 3 } END 8. Security Considerations The swmMIB module can be used for configuration of certain objects, and anything that can be configured can be incorrectly configured, with potentially disastrous results. Because this MIB module reuses the IP tunnel MIB, the security considerations of the IP tunnel MIB is also applicable to the Softwire mesh MIB. SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPsec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module. It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC3410], section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy). Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator's responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 9. IANA Considerations The MIB module in this document uses the following IANA-assigned OBJECT IDENTIFIER values recorded in the SMI Numbers registry, and the following IANA-assigned tunnelType values recorded in the IANAtunnelType-MIB registry: Cui, et al. Expires September 13, 2012 [Page 11] Internet-Draft swmMIB March 2012 Descriptor OBJECT IDENTIFIER value ---------- ----------------------- swmMIB { transmission XXX } IANAtunnelType ::= TEXTUAL-CONVENTION SYNTAX INTEGER { softwireMesh ("XX") -- softwire Mesh tunnel } 10. References 10.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [RFC4925] Li, X., Dawkins, S., Ward, D., and A. Durand, "Softwire Problem Statement", RFC 4925, July 2007. [RFC5512] Mohapatra, P. and E. Rosen, "The BGP Encapsulation Subsequent Address Family Identifier (SAFI) and the BGP Tunnel Encapsulation Attribute", RFC 5512, April 2009. [RFC5565] Wu, J., Cui, Y., Metz, C., and E. Rosen, "Softwire Mesh Framework", RFC 5565, June 2009. 10.2. Informative References [RFC2223] Postel, J. and J. Reynolds, "Instructions to RFC Authors", RFC 2223, October 1997. Cui, et al. Expires September 13, 2012 [Page 12] Internet-Draft swmMIB March 2012 [RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet-Standard Management Framework", RFC 3410, December 2002. [RFC2629] Rose, M., "Writing I-Ds and RFCs using XML", RFC 2629, June 1999. [RFC4181] Heard, C., "Guidelines for Authors and Reviewers of MIB Documents", BCP 111, RFC 4181, September 2005. 10.3. URL References [idguidelines] IETF Internet Drafts editor, "http://www.ietf.org/ietf/1id-guidelines.txt". [idnits] IETF Internet Drafts editor, "http://www.ietf.org/ID-Checklist.html". [xml2rfc] XML2RFC tools and documentation, "http://xml.resource.org". [ops] the IETF OPS Area, "http://www.ops.ietf.org". [ietf] IETF Tools Team, "http://tools.ietf.org". Authors' Addresses Yong Cui Tsinghua University Department of Computer Science, Tsinghua University Beijing 100084 P.R.China Phone: +86-10-6260-3059 EMail: yong@csnet1.cs.tsinghua.edu.cn Jiang Dong Tsinghua University Department of Computer Science, Tsinghua University Beijing 100084 P.R.China Phone: +86-10-6278-5822 EMail: dongjiang@csnet1.cs.tsinghua.edu.cn Cui, et al. Expires September 13, 2012 [Page 13] Internet-Draft swmMIB March 2012 Peng Wu Tsinghua University Department of Computer Science, Tsinghua University Beijing 100084 P.R.China Phone: +86-10-6278-5822 EMail: weapon@csnet1.cs.tsinghua.edu.cn Mingwei Xu Tsinghua University Department of Computer Science, Tsinghua University Beijing 100084 P.R.China Phone: +86-10-6278-5822 EMail: xmw@cernet.edu.cn Cui, et al. Expires September 13, 2012 [Page 14]