Network Working Group E. Hammer-Lahav
Internet-Draft Yahoo!
Intended status: Standards Track A. Barth
Expires: November 10, 2011 Google
B. Adida
Mozilla
May 09, 2011

HTTP Authentication: MAC Access Authentication
draft-hammer-oauth-v2-mac-token-04

Abstract

This document specifies the HTTP MAC access authentication scheme, an HTTP authentication method using a message authentication code (MAC) algorithm to provide cryptographic verification of portions of HTTP requests. The document also defines an OAuth 2.0 binding for use as an access-token type, as well as an extension attribute to the HTTP Set-Cookie response header field.

Status of this Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on November 10, 2011.

Copyright Notice

Copyright (c) 2011 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.


Table of Contents

1. Introduction

This specification defines the HTTP MAC access authentication scheme, providing a method for making authenticated HTTP requests with partial cryptographic verification of the request, covering the HTTP method, request URI, host, and in some cases the request body.

Similar to the HTTP Basic access authentication scheme [RFC2617], the MAC scheme utilizes a set of client credentials which include an identifier and key. However, in contrast with the Basic scheme, the key is never included in authenticated requests but is used to calculate the request MAC value which is included instead.

[[ Add note about design constraints (eg sign an HTTP request without any interactivity with the server; suitable for shared secret keys, but not for shared passwords) ]]

The MAC scheme requires the establishment of a shared symmetric key between the client and the server. This is often accomplished through a manual process such as client registration. This specification offers two methods for issuing a set of MAC credentials to the client using:

[[ Please discuss this draft on the apps-discuss@ietf.org mailing list. ]]

1.1. Example

The client attempts to access a protected resource without authentication, making the following HTTP request to the resource server:

            
  GET /resource/1?b=1&a=2 HTTP/1.1
  Host: example.com

          

The resource server returns the following authentication challenge:

            
  HTTP/1.1 401 Unauthorized
  WWW-Authenticate: MAC

          

The client has previously obtained a set of MAC credentials for accessing resources on the http://example.com/ server. The MAC credentials issued to the client include the following attributes:

MAC key identifier:
h480djs93hd8
MAC key:
489dks293j39
MAC algorithm:
hmac-sha-1
Issuer:
login.example.net:443
Issue time:
Date: Thu, 02 Dec 2010 21:39:45 GMT

The client constructs the authentication header by calculating the credentials' age (number of seconds since the credentials were issued) and generating a nonce. The nonce is unique to the age value used, typically a random string:

Age:
264095
Nonce:
dj83hs9s

The client normalizes the request and constructs the normalized request string (the new line separator character is represented by \n for display purposes only):

            
  login.example.net:443\n
  264095\n
  dj83hs9s\n
  GET\n
  /resource/1?b=1&a=2\n
  example.com\n
  80\n
  \n
  \n

          

The two trailing new line separators signify that no body hash or extension value are included with the request.

The request MAC is calculated using the specified MAC algorithm hmac-sha-1 and the MAC key over the normalized request string. The result is base64-encoded to produce the request MAC:

            
  TkrWtyTiys3Iw6MF/zI7gbVs5lA=

          

The client includes the MAC key identifier, issuer, age, nonce, and request MAC with the request using the Authorization request header field:

            
  GET /resource/1?b=1&a=2 HTTP/1.1
  Host: example.com
  Authorization: MAC id="h480djs93hd8",
                     issuer="login.example.net:443",
                     age="264095",
                     nonce="dj83hs9s",
                     mac="TkrWtyTiys3Iw6MF/zI7gbVs5lA="

          

The server validates the request by calculating the request MAC again based on the request received and verifies the validity and scope of the MAC credentials. If valid, the server responds with the requested resource representation.

1.2. Notational Conventions

The key words 'MUST', 'MUST NOT', 'REQUIRED', 'SHALL', 'SHALL NOT', 'SHOULD', 'SHOULD NOT', 'RECOMMENDED', 'MAY', and 'OPTIONAL' in this specification are to be interpreted as described in [RFC2119].

This specification uses the Augmented Backus-Naur Form (ABNF) notation of [I-D.ietf-httpbis-p1-messaging]. Additionally, the following rules are included from [RFC2617]: auth-param.

2. Issuing MAC Credentials

This specification defines two method for issuing MAC credentials using OAuth 2.0 as described in Section 5 and using the HTTP Set-Cookie response header field as described in Section 6.

This specification does not mandate servers to support any particular method for issuing MAC credentials, and other methods MAY be defined and used. Whenever MAC credentials are issued, the credentials MUST include the following attributes:

MAC key identifier

A string identifying the MAC key used to calculate the request MAC. The string is usually opaque to the client. The server typically assigns a specific scope and lifetime to each set of MAC credentials. The identifier MAY denote a unique value used to retrieve the authorization information (e.g. from a database), or self-contain the authorization information in a verifiable manner (i.e. a string consisting of some data and a signature).
MAC key

A shared symmetric secret used as the MAC algorithm key. The server MUST NOT issue the same MAC key and MAC key identifier combination.
MAC algorithm

A MAC algorithm used to calculate the request MAC. Value MUST be one of hmac-sha-1, hmac-sha-256, or a registered extension algorithm name as described in Section 8.1. Algorithm names are case-sensitive. If the MAC algorithm is not understood by the client, the client MUST NOT use the MAC credentials and continue as if no MAC credentials were issued.
Issuer

A string identifying the entity issuing the credentials. The content and format of the issuer attribute depends on the method used to obtain the credentials.
Issue time

The time when the credentials were issued, used to calculate the credentials age when making requests. If the MAC credentials were obtained via an HTTP response, the time of issue is the time the response was received by the client.

The MAC key identifier, MAC key, MAC algorithm, and issuer strings MUST NOT include characters other than:

          
  %x20-21 / %x23-5B / %x5D-7E
  ; Any printable ASCII character except for <"> and <\>

        

3. Making Requests

To make authenticated requests, the client must be in the possession of a valid set of MAC credentials accepted by the server. The client constructs the request by calculating a set of attributes, and adding them to the HTTP request using the Authorization request header field as described in Section 3.1.

3.1. The "Authorization" Request Header

The Authorization request header field uses the framework defined by [RFC2617] as follows:

            
  credentials    = 'MAC' [ RWS 1#param ]
  
  param          = id /
                   issuer /
                   age /
                   nonce /
                   body-hash /
                   ext /
                   mac

  id             = 'id' '=' <"> plain-string <">
  issuer         = 'issuer' '=' <"> plain-string <">
  age            = 'age' '=' <"> 1*DIGIT <">
  nonce          = 'nonce' '=' <"> plain-string <">
  body-hash      = 'bodyhash' '=' <"> plain-string <">
  ext            = 'ext' '=' <"> plain-string <">
  mac            = 'mac' '=' <"> plain-string <">
  
  plain-string   = 1*( %x20-21 / %x23-5B / %x5D-7E )

          

The header attributes are set as follows:

id

REQUIRED. The MAC key identifier.
issuer

REQUIRED. The identifier of the entity who issued the MAC credentials.
age

REQUIRED. The number of second since the MAC credentials were issued to the client. The value MUST be a positive integer and MUST NOT include leading zeros (e.g. "000137131200").
nonce

REQUIRED. A random string, uniquely generated by the client to allow the server to verify that a request has never been made before and helps prevent replay attacks when requests are made over an insecure channel. The nonce value MUST be unique across all requests with the same age and MAC key identifier combination.
To avoid the need to retain an infinite number of nonce values for future checks, the server MAY choose to restrict the time period after which a request with an old age is rejected. If such a restriction is enforced, the server SHOULD allow for a sufficiently large window to accommodate network delays which will affect the credentials issue time used by the client to calculate the credentials' age.
bodyhash

OPTIONAL. The HTTP request payload body hash as described in Section 3.2.
ext

OPTIONAL. A string used to include additional information which is covered by the request MAC. The content and format of the string is beyond the scope of this specification.
mac

REQUIRED. The HTTP request MAC as described in Section 3.3.

Attributes MUST NOT appear more than once. Attribute values are limited to a subset of ASCII, which does not require escaping, as defined by the plain-string ABNF.

3.2. Body Hash

[[ Need to figure out exactly when body-hash is required ]]

The body hash is used to provide integrity verification of the HTTP request payload body. The body hash value is calculated using a hash algorithm over the entire HTTP request payload body.

The client MAY include the body hash with any request. The server SHOULD require the calculation and inclusion of the body hash with any request containing an payload body, or when the presence (or lack of) of an payload body is of significance.

The body hash algorithm is determined by the MAC algorithm. The SHA-1 hash algorithm as defined by [NIST FIPS-180-3] is used with the hmac-sha-1 MAC algorithm. The SHA-256 hash algorithm as defined by [NIST FIPS-180-3] is used with the hmac-sha-256 MAC algorithm. Additional MAC algorithms MUST specify the corresponding body hash algorithm.

The body hash is calculated as follows:

            
  bodyhash = BASE64 ( HASH (text) )

          

Where:

HASH

is the hash algorithm function,
text

is the HTTP request payload body,
BASE64

is the base64-encoding function per [RFC2045] section 6.8, applied to the hash result octet string, and
bodyhash

is the value used in the normalized request string and to set the bodyhash attribute of the Authorization request header field.

The body hash is calculated before the normalized request string is constructed and the request MAC is calculated.

For example, the HTTP request:

            
  POST /request HTTP/1.1
  Host: example.net
  Content-Type: application/x-www-form-urlencoded

  hello=world%21

          

using MAC key identifier jd93dh9dh39D, issuer auth.example.net:443, age 273156, nonce di3hvdf8, MAC algorithm hmac-sha-1, and MAC key 8yfrufh348h, is transmitted as (line breaks are for display purposes only):

            
  POST /request HTTP/1.1
  Host: example.com
  Content-Type: application/x-www-form-urlencoded
  Authorization: MAC id="jd93dh9dh39D",
                     issuer="login.example.com:443",
                     age="273156",
                     nonce="di3hvdf8",
                     bodyhash="k9kbtCIy0CkI3/FEfpS/oIDjk6k=",
                     mac="+PrdikQm1erX2/0YIVhUPHl7yDc="

  hello=world%21

          

3.3. Request MAC

The client uses the MAC algorithm and the MAC key to calculate the request MAC. This specification defines two algorithms: hmac-sha-1 and hmac-sha-256, and provides an extension registry for additional algorithms.

3.3.1. Normalized Request String

The normalized request string is a consistent, reproducible concatenation of several of the HTTP request elements into a single string. By normalizing the request into a reproducible string, the client and server can both calculate the request MAC over the exact same value.

The string is constructed by concatenating together, in order, the following HTTP request elements, each followed by a new line character (%x0A):

  1. The MAC credentials issuer identifier exactly as included with the request using the issuer attribute.
  2. The age value calculated for the request.
  3. The nonce value generated for the request.
  4. The HTTP request method in upper case. For example: HEAD, GET, POST, etc.
  5. The HTTP request-URI as defined by [RFC2616] section 5.1.2.
  6. The hostname included in the HTTP request using the Host request header field in lower case.
  7. The port as included in the HTTP request using the Host request header field. If the header field does not include a port, the default value for the scheme MUST be used (e.g. 80 for HTTP and 443 for HTTPS).
  8. The request payload body hash as described in Section 3.2 if one was calculated and included in the request, otherwise, an empty string. Note that the body hash of an empty payload body is not an empty string.
  9. The value of the ext Authorization request header field attribute if one was included in the request, otherwise, an empty string.

Each element is followed by a new line character (%x0A) including the last element and even when an element value is an empty string.

For example, the HTTP request:

              
  POST /request?b5=%3D%253D&a3=a&c%40=&a2=r%20b&c2&a3=2+q HTTP/1.1
  Host: example.com

  Hello World!

            

using issuer login.example.com:443, age 264095, nonce 7d8f3e4a, body hash Lve95gjOVATpfV8EL5X4nxwjKHE=, and extension string a,b,c is normalized into the following string (the new line separator character is represented by \n for display purposes only):

              
  login.example.com:443\n
  264095\n
  7d8f3e4a\n
  POST\n
  /request?b5=%3D%253D&a3=a&c%40=&a2=r%20b&c2&a3=2+q\n
  example.com\n
  80\n
  Lve95gjOVATpfV8EL5X4nxwjKHE=\n
  a,b,c\n

            

3.3.2. hmac-sha-1

hmac-sha-1 uses the HMAC-SHA1 algorithm as defined in [RFC2104]:

              
  mac = HMAC-SHA1 (key, text)

            

Where:

text

is set to the value of the normalized request string as described in Section 3.3.1,
key

is set to the MAC key provided by the server, and
mac

is used to set the value of the mac attribute, after the result octet string is base64-encoded per [RFC2045] section 6.8.

The SHA-1 hash algorithm as defined by [NIST FIPS-180-3] is used for generating the body hash attribute described in Section 3.2 when using MAC credentials with the hmac-sha-1 MAC algorithm.

3.3.3. hmac-sha-256

hmac-sha-256 uses the HMAC algorithm as defined in [RFC2104] together with the SHA-256 hash function defined in [NIST FIPS-180-3]:

              
  mac = HMAC-SHA256 (key, text)

            

Where:

text

is set to the value of the normalize request string as described in Section 3.3.1,
key

is set to the MAC key provided by the server, and
mac

is used to set the value of the mac attribute, after the result octet string is base64-encoded per [RFC2045] section 6.8.

The SHA-256 hash algorithm as defined by [NIST FIPS-180-3] is used for generating the body hash attribute described in Section 3.2 when using MAC credentials with the hmac-sha-256 MAC algorithm.

4. Verifying Requests

A server receiving an authenticated request validates it by performing the following REQUIRED steps:

  1. Recalculate the request body hash (if included in the request) as described in Section 3.2 and request MAC as described in Section 3.3 and compare the request MAC to the value received from the client via the mac attribute.
  2. Ensure that the combination of nonce, age, and MAC key identifier received from the client has not been used before in a previous request (the server MAY reject requests with stale timestamps; the determination of staleness is left up to the server to define).
  3. Verify the scope and validity of the MAC credentials.

If the request fails verification, the server response includes the WWW-Authenticate response header field as described in Section 4.1 and SHOULD include one of the following HTTP status codes:

401 (Unauthorized)

The Authorization request header field is not included, missing a required parameter, includes an unsupported parameter or parameter value, repeats the same parameter, or is otherwise malformed. The MAC credentials provided are expired, revoked, malformed, or invalid. The body hash or request MAC provided do not match the values calculated by the server, or a body hash is required but missing.
307 (Temporary Redirect)

Same as 401, with the exception that a human intervention at the destination URI (identified by the Location response header field) MAY resolve the issue (e.g. provide a login page which upon a successful authentication will issue the user-agent a new set of MAC credentials using the Set-Cookie response header field as described in Section 6.

4.1. The "WWW-Authenticate" Response Header Field

If the protected resource request does not include authentication credentials, contains an invalid MAC key identifier, or is malformed, the server SHOULD include the HTTP WWW-Authenticate response header field.

For example:

            
  HTTP/1.1 401 Unauthorized
  WWW-Authenticate: MAC

          

The WWW-Authenticate request header field uses the framework defined by [RFC2617] as follows:

            
  challenge   = "MAC" [ RWS 1#param ]
  param       = error / auth-param
  error       = "error" "=" quoted-string

          

Each attribute MUST NOT appear more than once.

If the protected resource request included a MAC Authorization request header field and failed authentication, the server MAY include the error attribute to provide the client with a human-readable explanation why the access request was declined.

For example:

            
  HTTP/1.1 401 Unauthorized
  WWW-Authenticate: MAC error="The MAC credentials expired"

          

5. Use with OAuth 2.0

OAuth 2.0 ([I-D.ietf-oauth-v2]) defines a token-based authentication framework in which third-party applications (clients) access protected resources using access tokens. Access tokens are obtained via the resource owners' authorization from an authorization server. This specification defines the OAuth 2.0 MAC token type, as well as type-specific token attributes.

This specification does not define methods for the client to specifically request a MAC-type token from the authorization server. Additionally, it does not include any discovery facilities for identifying which HMAC algorithms are supported by a resource server, or how the client may go about obtaining MAC access tokens for any given protected resource.

The authorization server MUST require the use of a transport-layer security mechanism when sending requests to the token endpoint to obtain a MAC token.

5.1. Issuing MAC-Type Access Tokens

Authorization servers issuing MAC-type access tokens MUST include the following parameters whenever a response includes the access_token parameter:

access_token

REQUIRED. The MAC key identifier.
secret

REQUIRED. The MAC key.
algorithm

REQUIRED. The MAC algorithm used to calculate the request MAC. Value MUST be one of hmac-sha-1, hmac-sha-256, or a registered extension algorithm name as described in Section 8.1.

The issuer attribute MUST be determined by the client alone, and set to the host and port of the token endpoint used to make the HTTP request to obtain the credentials, separated by a colon character (%x3A). For example, 'auth.example.com:443'. If the client followed any redirections before receiving the credentials, it MUST use the host and port of the final request (the request resulting in the transmission of the MAC credential).

6. Use with Set-Cookie

The HTTP Set-Cookie response header field defined in [RFC6265] enables the server to set persistent information which the client repeats back on follow-up requests. Each cookie includes a name-value pair which is sent back to the server, and a set of attributes which inform the client when to include the cookie in follow-up requests. The attributes are never sent back to the server.

This specification defines the MAC-Key and MAC-Algorithm cookie attributes, which are used by the server, together with the cookie name which includes the MAC key identifier, to issue the client a set of MAC credentials.

The issuer attribute MUST be determined by the client alone, and set to the host and port of the token endpoint used to make the HTTP request to obtain the credentials, separated by a colon character (%x3A). For example, 'auth.example.com:443'. If the client followed any redirections before receiving the credentials, it MUST use the host and port of the final request (the request resulting in the transmission of the credential).

The server MUST only include the MAC-Key attribute in response to requests made using a transport-layer security mechanism such as TLS 1.2 as defined in [RFC5246]. Clients MUST discard any MAC credentials received over an insecure channel.

For example, after a successful end-user authentication, the server includes the following response header field (line breaks are for display purposes only):

          
  Set-Cookie: SID=31d4d96e407aad42; Path=/; Domain=example.com;
              MAC-Key=8yfrufh348h; MAC-Algorithm=hmac-sha-1

        

which provides the client with the necessary MAC credentials. The cookie name SID is used as the MAC key identifier together with the other MAC-specific attributes. The user-agent uses the MAC credentials for subsequent HTTP requests that match the scope of the cookie, in this case for example.com and all subdomains.

6.1. User Agent Requirements

This section updates [RFC6265], adding the ability to issue MAC credentials using the Set-Cookie response header field.

6.1.1. The Set-Cookie Header

Add the following two subsections to the end of Section 5.2 (The Set-Cookie Header) in [RFC6265]. These sections instruct the user-agent how to parse the MAC-Key attribute and MAC-Algorithm attribute, respectively.

6.1.1.1. The MAC-Key attribute

If the attribute-name case-insensitively matches the string MAC-Key, the user-agent MUST append an attribute to the cookie-attribute-list with an attribute name of MAC-Key and a attribute-value equal to the attribute-value.

6.1.1.2. The MAC-Algorithm attribute

If the attribute-name case-insensitively matches the string MAC-Algorithm, and if the attribute-value is either hmac-sha-1, hmac-sha-256, or a registered extension value, the user-agent MUST append an attribute to the cookie-attribute-list with an attribute name of MAC-Algorithm and an attribute-value equal to the attribute-value.

6.1.2. Storage Model

The storage model for cookies is extended with three additional fields: mac-key, mac-algorithm, and issuer, all of which default to the empty string.

The user-agent MUST perform the follow steps after Step 10 of the algorithm in Section 5.3 of [RFC6265]:

  1. If the cookie-attribute-list contains an attribute with an attribute-name of MAC-Key, set the cookie's mac-key field to the attribute-value of the last such attribute.
  2. If the cookie-attribute-list contains an attribute with an attribute-name of Mac-Algorithm, set the cookie's mac-algorithm field to the attribute-value of the last such attribute.
  3. Set the issuer field to the canonicalized request-host, as defined in [RFC6265] followed by a colon character (%x3A), and the port number of the request-uri (as defined in Section 5.1.2 of [RFC2616]).

When the user agent removes excess cookies from the cookie store because there are more than a predetermined number of cookies that share a domain field, or the combined length of cookies sharing a single domain field or being sent in a single request have exceeded a predetermined length, the user agent MUST evict cookies with an empty mac-key or an empty mac-algorithm field before cookies with both a non-empty mac-key and a non-empty mac-algorithm field.

6.1.3. The Authorization Header

In addition to being sent to the server in the Cookie request header field, cookies with MAC-Key and MAC-Algorithm attributes are also used to compute the Authorization request header field as described in Section 3.1.

The user-agent MAY ignore cookies for the purpose of generating the Authorization request header field. For example, the user-agent might wish to ignore cookies when issuing "third-party" requests or use MAC credentials obtained via other means.

When issuing an HTTP request, let cookie-list be the set of cookies defined in Section 5.4 of [RFC6265]. Further, let mac-cookie-list be those cookies in the cookie-list that contain both a non-empty mac-key and mac-algorithm fields.

Let the operative-cookie be the first cookie in the mac-cookie-list.

Include an Authorization request header field in the HTTP request as described in Section 3.1 using the cookie's MAC credentials where:

MAC key identifier

is equal to the operative-cookie's name,
MAC key

is equal to the operative-cookie's mac-key,
MAC algorithm

is equal to the operative-cookie's mac-algorithm, and
Issuer

is equal to the operative-cookie's issuer.
Issue time

is equal to the operative-cookie's creation-time.

7. Security Considerations

As stated in [RFC2617], the greatest sources of risks are usually found not in the core protocol itself but in policies and procedures surrounding its use. Implementers are strongly encouraged to assess how this protocol addresses their security requirements.

7.1. MAC Keys Transmission

This specification describes two mechanism for obtaining or transmitting MAC keys, both require the use of a transport-layer security mechanism when sending MAC keys to the client. Additional methods used to obtain MAC credentials must ensure that these transmissions are protected using transport-layer mechanisms such as TLS or SSL.

7.2. Confidentiality of Requests

While this protocol provides a mechanism for verifying the integrity of requests, it provides no guarantee of request confidentiality. Unless further precautions are taken, eavesdroppers will have full access to request content. Servers should carefully consider the kinds of data likely to be sent as part of such requests, and should employ transport-layer security mechanisms to protect sensitive resources.

7.3. Spoofing by Counterfeit Servers

This protocol makes no attempt to verify the authenticity of the server. A hostile party could take advantage of this by intercepting the client's requests and returning misleading or otherwise incorrect responses. Service providers should consider such attacks when developing services using this protocol, and should require transport-layer security for any requests where the authenticity of the resource server or of request responses is an issue.

7.4. Plaintext Storage of Credentials

The MAC key functions the same way passwords do in traditional authentication systems. In order to compute the request MAC, the server must have access to the MAC key in plaintext form. This is in contrast, for example, to modern operating systems, which store only a one-way hash of user credentials.

If an attacker were to gain access to these MAC keys - or worse, to the server's database of all such MAC keys - he or she would be able to perform any action on behalf of any resource owner. Accordingly, it is critical that servers protect these MAC keys from unauthorized access.

7.5. Entropy of MAC Keys

Unless a transport-layer security protocol is used, eavesdroppers will have full access to authenticated requests and request MAC values, and will thus be able to mount offline brute-force attacks to recover the MAC key used. Servers should be careful to assign MAC keys which are long enough, and random enough, to resist such attacks for at least the length of time that the MAC credentials are valid.

For example, if the MAC credentials are valid for two weeks, servers should ensure that it is not possible to mount a brute force attack that recovers the MAC key in less than two weeks. Of course, servers are urged to err on the side of caution, and use the longest MAC key reasonable.

It is equally important that the pseudo-random number generator (PRNG) used to generate these MAC keys be of sufficiently high quality. Many PRNG implementations generate number sequences that may appear to be random, but which nevertheless exhibit patterns or other weaknesses which make cryptanalysis or brute force attacks easier. Implementers should be careful to use cryptographically secure PRNGs to avoid these problems.

7.6. Denial of Service / Resource Exhaustion Attacks

This specification includes a number of features which may make resource exhaustion attacks against servers possible. For example, this protocol requires servers to track used nonces. If an attacker is able to use many nonces quickly, the resources required to track them may exhaust available capacity. And again, this protocol can require servers to perform potentially expensive computations in order to verify the request MAC on incoming requests. An attacker may exploit this to perform a denial of service attack by sending a large number of invalid requests to the server.

Resource Exhaustion attacks are by no means specific to this specification. However, implementers should be careful to consider the additional avenues of attack that this protocol exposes, and design their implementations accordingly. For example, entropy starvation typically results in either a complete denial of service while the system waits for new entropy or else in weak (easily guessable) MAC keys. When implementing this protocol, servers should consider which of these presents a more serious risk for their application and design accordingly.

7.7. Timing Attacks

This specification makes use of HMACs, for which a signature verification involves comparing the received MAC string to the expected one. If the string comparison operator operates in observably different times depending on inputs, e.g. because it compares the strings character by character and returns a negative result as soon as two characters fail to match, then it may be possible to use this timing information to determine the expected MAC, character by character.

Service implementers are encouraged to use fixed-time string comparators for MAC verification.

7.8. CSRF Attacks

A Cross-Site Request Forgery attack occurs when a site, evil.com, initiates within the victim's browser the loading of a URL from or the posting of a form to a web site where a side-effect will occur, e.g. transfer of money, change of status message, etc. To prevent this kind of attack, web sites may use various techniques to determine that the originator of the request is indeed the site itself, rather than a third party. The classic approach is to include, in the set of URL parameters or form content, a nonce generated by the server and tied to the user's session, which indicates that only the server could have triggered the action.

Recently, the Origin HTTP header has been proposed and deployed in some browsers. This header indicates the scheme, host, and port of the originator of a request. Some web applications may use this Origin header as a defense against CSRF.

To keep this specification simple, HTTP headers are not part of the string to be MAC'ed. As a result, MAC authentication cannot defend against header spoofing, and a web site that uses the Host header to defend against CSRF attacks cannot use MAC authentication to defend against active network attackers. Sites that want the full protection of MAC Authentication should use traditional, cookie-tied CSRF defenses.

7.9. Coverage Limitations

The normalized request string has been designed to support the authentication methods defined in this specification. Those designing additional methods, should evaluated the compatibility of the normalized request string with their security requirements. Since the normalized request string does not cover the entire HTTP request, servers should employ additional mechanisms to protect such elements.

The request MAC does not cover entity-header fields which can often affect how the request body is interpreted by the server (i.e. Content-Type). If the server behavior is influenced by the presence or value of such header fields, an attacker can manipulate the request header without being detected. This will alter the request even when using the body hash attribute.

7.10. Version Rollback Attack

[[ TODO ]]

8. IANA Considerations

8.1. The HTTP MAC Authentication Scheme Algorithm Registry

This specification establishes the HTTP MAC authentication scheme algorithm registry.

Additional MAC algorithms are registered on the advice of one or more Designated Experts (appointed by the IESG or their delegate), with a Specification Required (using terminology from [RFC5226]). However, to allow for the allocation of values prior to publication, the Designated Expert(s) may approve registration once they are satisfied that such a specification will be published.

Registration requests should be sent to the [TBD]@ietf.org mailing list for review and comment, with an appropriate subject (e.g., "Request for MAC Algorithm: example"). [[ Note to RFC-EDITOR: The name of the mailing list should be determined in consultation with the IESG and IANA. Suggested name: http-mac-ext-review. ]]

Within at most 14 days of the request, the Designated Expert(s) will either approve or deny the registration request, communicating this decision to the review list and IANA. Denials should include an explanation and, if applicable, suggestions as to how to make the request successful.

Decisions (or lack thereof) made by the Designated Expert can be first appealed to Application Area Directors (contactable using app-ads@tools.ietf.org email address or directly by looking up their email addresses on http://www.iesg.org/ website) and, if the appellant is not satisfied with the response, to the full IESG (using the iesg@iesg.org mailing list).

IANA should only accept registry updates from the Designated Expert(s), and should direct all requests for registration to the review mailing list.

8.1.1. Registration Template

Algorithm name:

The name requested (e.g., "example").
Body hash algorithm:

The corresponding algorithm used to calculate the payload body hash.
Change controller:

For standards-track RFCs, state "IETF". For others, give the name of the responsible party. Other details (e.g., postal address, e-mail address, home page URI) may also be included.
Specification document(s):

Reference to document that specifies the algorithm, preferably including a URI that can be used to retrieve a copy of the document. An indication of the relevant sections may also be included, but is not required.

8.1.2. Initial Registry Contents

The HTTP MAC authentication scheme algorithm registry's initial contents are:

8.2. OAuth Access Token Type Registration

This specification registers the following access token type in the OAuth Access Token Type Registry.

8.2.1. The "mac" OAuth Access Token Type

Type name:

mac
Additional Token Endpoint Response Parameters:

secret, algorithm
HTTP Authentication Scheme(s):

MAC
Change controller:

IETF
Specification document(s):

[[ this document ]]

8.3. OAuth Parameters Registration

This specification registers the following parameters in the OAuth Parameters Registry established by [I-D.ietf-oauth-v2].

8.3.1. The "secret" OAuth Parameter

Parameter name:
secret
Parameter usage location:
authorization response, token response
Change controller:
IETF
Specification document(s):
[[ this document ]]
Related information:
None

8.3.2. The "algorithm" OAuth Parameter

Parameter name:
algorithm
Parameter usage location:
authorization response, token response
Change controller:
IETF
Specification document(s):
[[ this document ]]
Related information:
None

9. Acknowledgments

The authors would like to thank Rasmus Lerdorf, James Manger, Scott Renfro, Toby White, Peter Wolanin, and Skylar Woodward for their suggestions and feedback.

10. References

10.1. Normative References

[RFC2045] Freed, N. and N.S. Borenstein, "Multipurpose Internet Mail Extensions (MIME) Part One: Format of Internet Message Bodies", RFC 2045, November 1996.
[RFC2104] Krawczyk, H., Bellare, M. and R. Canetti, "HMAC: Keyed-Hashing for Message Authentication", RFC 2104, February 1997.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2616] Fielding, R., Gettys, J., Mogul, J., Frystyk, H., Masinter, L., Leach, P. and T. Berners-Lee, "Hypertext Transfer Protocol -- HTTP/1.1", RFC 2616, June 1999.
[RFC2617] Franks, J., Hallam-Baker, P.M., Hostetler, J.L., Lawrence, S.D., Leach, P.J., Luotonen, A. and L. Stewart, "HTTP Authentication: Basic and Digest Access Authentication", RFC 2617, June 1999.
[RFC3986] Berners-Lee, T., Fielding, R. and L. Masinter, "Uniform Resource Identifier (URI): Generic Syntax", STD 66, RFC 3986, January 2005.
[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 5226, May 2008.
[RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security (TLS) Protocol Version 1.2", RFC 5246, August 2008.
[RFC6265] Barth, A., "HTTP State Management Mechanism", RFC 6265, April 2011.
[I-D.ietf-httpbis-p1-messaging] Fielding, R, Gettys, J, Mogul, J, Nielsen, H, Masinter, L, Leach, P, Berners-Lee, T and J Reschke, "HTTP/1.1, part 1: URIs, Connections, and Message Parsing", Internet-Draft draft-ietf-httpbis-p1-messaging-13, March 2011.
[I-D.ietf-oauth-v2] Hammer-Lahav, E, Recordon, D and D Hardt, "The OAuth 2.0 Authorization Protocol", Internet-Draft draft-ietf-oauth-v2-15, April 2011.
[W3C.REC-html401-19991224] Raggett, D., Hors, A. and I. Jacobs, "HTML 4.01 Specification", World Wide Web Consortium Recommendation REC-html401-19991224, December 1999.
[NIST FIPS-180-3] National Institute of Standards and Technology, "Secure Hash Standard (SHS). FIPS PUB 180-3, October 2008", .

10.2. Informative References

[RFC5849] Hammer-Lahav, E., "The OAuth 1.0 Protocol", RFC 5849, April 2010.

Authors' Addresses

Eran Hammer-Lahav Yahoo! EMail: eran@hueniverse.com URI: http://hueniverse.com
Adam Barth Google EMail: ietf@adambarth.com URI: http://www.adambarth.com
Ben Adida Mozilla EMail: ben@adida.net URI: http://ben.adida.net