TOC 
6LoWPAN Working GroupE. Kim
Internet-DraftETRI
Expires: January 29, 2011D. Kaspar
 Simula Research Laboratory
 N. Chevrollier
 TNO
 JP. Vasseur
 Cisco Systems, Inc
 July 28, 2010


Design and Application Spaces for 6LoWPANs
draft-ietf-6lowpan-usecases-06

Abstract

This document investigates potential application scenarios and use cases for low-power wireless personal area networks (LoWPANs). This document provides dimensions of design space for LoWPAN applications. A list of use cases and market domains that may benefit and motivate the work currently done in the 6LoWPAN WG is provided with the characterisitcis of each dimention. A complete list of practical use cases is not the goal of this document.

Status of this Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as “work in progress.”

This Internet-Draft will expire on January 29, 2011.

Copyright Notice

Copyright (c) 2010 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.



Table of Contents

1.  Introduction
    1.1.  Terminology
    1.2.  Basic Network Configuration
2.  Design Space
3.  Application Scenarios
    3.1.  Industrial Monitoring
        3.1.1.  A Use Case and its Requirements
        3.1.2.  6LoWPAN Applicability
    3.2.  Structural Monitoring
        3.2.1.  A Use Case and its Requirements
        3.2.2.  6LoWPAN Applicability
    3.3.  Connected Home
        3.3.1.  A Use Case and its Requirements
        3.3.2.  6LoWPAN Applicability
    3.4.  Healthcare
        3.4.1.  A Use Case and its Requirements
        3.4.2.  6LoWPAN Applicability
    3.5.  Vehicle Telematics
        3.5.1.  A Use Case and its Requirements
        3.5.2.  6LoWPAN Applicability
    3.6.  Agricultural Monitoring
        3.6.1.  A Use Case and its Requirements
        3.6.2.  6LoWPAN Applicability
4.  Security Considerations
5.  Acknowledgements
6.  References
    6.1.  Normative References
    6.2.  Informative References
§  Authors' Addresses




 TOC 

1.  Introduction

Low-power and lossy networks (LLNs) is the term commonly used to refer to networks made of highly constrained nodes (limited CPU, memory, power) interconnected by a variety of “lossy” links (low-power radio links or powerline communication (PLC)). They are characterized by low speed, low performance, low cost, and unstable connectivity. A LoWPAN is a particular instance of an LLN, formed by devices complying with the IEEE 802.15.4 standard [5] (IEEE Computer Society, “IEEE Std. 802.15.4-2006 (as amended),” 2007.). Their typical characteristics can be summarized as follows:

As any other LLN, a LoWPAN does not necessarily comprise of sensor nodes only, but may also consist of actuators. For instance, in an agricultural environment, sensor nodes might be used to detect low soil humidity and then send commands to activate the sprinkler system.

After defining common terminology in Section 1.1 (Terminology) and describing the characteristics of LoWPANs in Section 2 (Design Space), this document provides a list of use cases and market domains that may benefit and motivate the work currently done in the 6LoWPAN WG.



 TOC 

1.1.  Terminology

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [1] (Bradner, S., “Key words for use in RFCs to Indicate Requirement Levels,” March 1997.).

Readers are expected to be familiar with all the terms and concepts that are discussed in "IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs): Overview, Assumptions, Problem Statement, and Goals" (Kushalnagar, N., Montenegro, G., and C. Schumacher, “IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs): Overview, Assumptions, Problem Statement, and Goals,” August 2007.) [3], and " Transmission of IPv6 Packets over IEEE 802.15.4 Networks" (Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler, “Transmission of IPv6 Packets over IEEE 802.15.4 Networks,” September 2007.) [4].

Readers would benefit from reading 6LoWPAN ND [6] (Shelby, Z., Chakrabarti, S., and E. Nordmark, “Neighbor Discovery Optimization for Low-power and Lossy Networks,” July 2010.), 6LoWPAN header compression [7] (Hui, J. and P. Thubert, “Compression Format for IPv6 Datagrams in 6LoWPAN Networks,” July 2010.), and 6LoWPAN Routing Requirements [8] (Kim, E., Kaspar, D., Gomez, C., and C. Bormann, “Problem Statement and Requirements for 6LoWPAN Routing,” March 2010.) for the details of the each 6LoWPAN work.

This specification makes extensive use of the same terminology defined in 6LoWPAN ND [6] (Shelby, Z., Chakrabarti, S., and E. Nordmark, “Neighbor Discovery Optimization for Low-power and Lossy Networks,” July 2010.) unless otherwise redefined below.

This document defines additional terms:

LN (LoWPAN Node)
Any host or router participating in a LoWPAN. This term is used when referring to situations in which either a host or router can play the role described.
LR(LoWPAN Router)
An intermediate router in the LoWPAN who can communicate with other LoWPAN routers in the same LoWPAN. LoWPAN routers are present only in Route Over topologies.
LM (LoWPAN Mesh Node)
A LoWPAN node that forwards data between arbitary source-destination pairs using link-layer addresses and thus only exists in Mesh Under topologies.
LC(local-controller)
A logical functional entity that performs the special role of coordinating and controlling its child nodes for local data aggregation, status management of local nodes, etc. Thus, the local controller nodes may be multiple instance in a LoWPAN.
LBR (LoWPAN Border Router)
A border router located at the junction of separate LoWPAN networks or between a LoWPAN network and another IP network. There may be one or more LBRs at the LoWPAN network boundary. A LBR is the responsible authority for IPv6 Prefix propagation for the LoWPAN network it is serving. An isolated LoWPAN also contains a LBR in the network, which provides the prefix(es) for the isolated network.



 TOC 

1.2.  Basic Network Configuration

The IEEE 802.15.4 standard distinguishes between two types of nodes, reduced-function devices (RFDs) and full-function devices (FFDs). As this distinction is based on some MAC features that are not always in use, we are not using this distinction in this document.



 TOC 

2.  Design Space

Inspired by [9] (Roemer, K. and F. Mattern, “The Design Space of Wireless Sensor Networks,” December 2004.), this section lists the dimensions used to describe the design space of wireless sensor networks in the context of the 6LoWPAN Working Group. The design space is already limited by the unique characteristics of a LoWPAN (e.g., low-power, short range, low-bit rate) as described in [3] (Kushalnagar, N., Montenegro, G., and C. Schumacher, “IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs): Overview, Assumptions, Problem Statement, and Goals,” August 2007.). The possible dimensions for scenario categorization used in this document are described as follows:



 TOC 

3.  Application Scenarios

This section lists a fundamental set of LoWPAN application scenarios in terms of system design. A complete list of practical use cases is not the objective of this document.



 TOC 

3.1.  Industrial Monitoring

LoWPAN applications for industrial monitoring can be associated with a broad range of methods to increase productivity, energy efficiency, and safety of industrial operations in engineering facilities and manufacturing plants. Many companies currently use time-consuming and expensive manual monitoring to predict failures and to schedule maintenance or replacements in order to avoid costly manufacturing downtime. LoWPANs can be inexpensively installed to provide more frequent and more reliable data. The deployment of LoWPANs can reduce equipment downtime and eliminate manual equipment monitoring that is costly to be carried out. Additionally, data analysis functionality can be placed into the network, eliminating the need for manual data transfer and analysis.

Industrial monitoring can be largely split into the following application fields:



 TOC 

3.1.1.  A Use Case and its Requirements

Example: Hospital Storage Rooms

In a hospital, maintenance of the right temperature in storage rooms is very critical. Red blood cells need to be stored at 2 to 6 degrees Celsius, blood platelets at 20 to 24 C, and blood plasma below -18 C. For anti-cancer medicine, maintaining a humidity of 45% to 55% is required. Storage rooms have temperature sensors and humidity sensors every 25m to 100m, based on the floor plan and the location of shelves, as indoor obstacles distort the radio signals. At each blood pack a sensor tag can be installed to track the temperature during delivery. A LoWPAN node is installed in each container of a set of blood packs. In this case, highly dense networks must be managed.

All nodes are statically deployed and manually configured with either a single- or multi-hop connection. Different types of LoWPAN nodes are configured based on the service and network requirements.

All LoWPAN nodes do not move unless the blood packs or a container of blood packs is moved. Moving nodes get connected by logical attachment to a new LoWPAN. When containers of blood packs are transferred to another place of the hospital or by ambulance, the LoWPAN nodes on the containers associate to a new LoWPAN.

This type of application works based on both periodic and event-driven notifications. Periodic data is used for monitoring the temperature and humidity in the storage rooms. The data over or under a pre-defined threshold is meaningful to report. Blood cannot be used if it is exposed to the wrong environment for about 30 minutes. Thus, event-driven data sensed on abnormal occurrences is time-critical and requires secure and reliable transmission.

LoWPANs must be provided with low installation and management costs, and for the transportation of boold containers, precise location tracking of containers is important. The hospital network manager or staff can be provided with an early warning of possible chain ruptures, for example by conveniently accessing comprehensive online reports and data management systems.

Dominant parameters in industrial monitoring scenarios:



 TOC 

3.1.2.  6LoWPAN Applicability

The network configuration of the above use case can differ substantially by system design. As illustrated in Figure 1 (Storage rooms with a simple star topology), the simplest way is to build a star topology inside of each storage room, and connect the storage rooms with one link but overall network configuration is with mesh topologies. Each LoWPAN node reaches the LBR by a pre-defined routing/forwarding mechanism. LCs play a role in aggregation of the sensed data. In case that the sensed data from an individual node is important, such as urgent event-driven data, it will not be accumulated (and further delayed) by the LoWPAN LCs but immediately relayed. In Route Over topologies, IP forwarding is used, while link-layer addresses in the mesh-header defined by RFC 4944 [4] (Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler, “Transmission of IPv6 Packets over IEEE 802.15.4 Networks,” September 2007.) are used for transmission in Mesh Under topologies .

Each LoWPAN node configures its link-local address and get a prefix from its LBR by an 6LoWPAN ND procedure [6] (Shelby, Z., Chakrabarti, S., and E. Nordmark, “Neighbor Discovery Optimization for Low-power and Lossy Networks,” July 2010.). Based on the layout and size of the storage room, the LoWPAN can be configured in a different way of mesh topology as shown in Figure 2 (Storage rooms with a mesh topology). More than one LoWPAN LCs can be installed in a storage room, and LCs collect data as relay points to transmit the sensed data toward the LBRs. LoWPAN nodes need to build a multi-hop connection to reach the LCs and LBR by either Mesh Under or Route Over. In Mesh Under, more than one LMs are selected for multi-hop transmission and the nodes MAY also play role in transmission multi-point traffic (multicast) by unicast method, not only role in data collection. In Route Over, LRs will handle multicast traffic to their LoWPAN links.

The data volume is usually not so big in this case, but data is sensitive for delay. Data aggregators can be installed for each storage room, or just one data aggregator can collect all data. To make a light transmission, UDP is likely to be chosen, but secure transmission and security mechanism MUST be added. To increase security, link-layer mechanisms and/or additional security mechanisms SHOULD be used.

Because a failure of a LoWPAN node can critically affect the storage of the blood packs, network management is important in this use-case. A light weight management mechanism MUST be provided for the management.

When a container is moved out from the storage room, and connected to the other hospital system (if the hospital buildings are fully or partly covered with LoWPANs), a mechanism to rebind to a new parent node and a new LoWPAN MUST be supported. In case that it is moved by an ambulance, it will be connected to an LBR in the vehicle. This typle of mobility is supported by 6LoWPAN ND and routing mechanism.

LoWPANs MUST be provided with low installation and management costs, providing benefits such as reduced inventory, and precise location tracking of containers, and mobile equipment (moving beds at the hospital or ambulances).



                     LBR
                      |                     LBR: LoWPAN Border Router
          LC----------LC----------LC        LC: Local Controller node
         / | \       / | \       / | \          (Data Aggregator)
        n  n  n     n  n  n     n  n  n      n: LoWPAN node

 Figure 1: Storage rooms with a simple star topology 




          +------------+-----------+
          |            |           |         LBR: LoWPAN Border Router
         LBR          LBR         LBR(LC)     LC: Local Controller node
          |            |           |             (Data Aggregator)
         LC - n       LC - n      n            n: LoWPAN Node
       /  |   |        |   |     / \
      n   n - LC   n - n - n    n - n
      |       | \          |    |\
      n       n  n - n     n    n n

 Figure 2: Storage rooms with a mesh topology 



 TOC 

3.2.  Structural Monitoring

Intelligent monitoring in facility management can make safety checks and periodic monitoring of the architecture status highly efficient. Mains-powered nodes can be included in the design phase of a construction or battery-equipped nodes can be added afterwards. All nodes are static and manually deployed. Some data is not critical for security protection (such as normal room temperature), but event-driven emergency data (such as fire alarm) MUST be handled in very critical manner.



 TOC 

3.2.1.  A Use Case and its Requirements

Example: Bridge Safety Monitoring

A 1000m long concrete bridge with 10 pillars is described. Each pillar and the bridge body contain 5 sensors to measure the water level, and 5 vibration sensors are used to monitor its structural health. The LoWPAN nodes are deployed to have 100m line-of-sight distance from each other. All nodes are placed statically and manually configured with a single-hop connection to the local coordinator. All LoWPAN nodes do not move while the service is provided. Except from the pillars, there are no special obstacles of attenuation to the node signals, but careful configuration is needed to prevent signal interference between LoWPAN nodes.

The physical network topology is changed in case of node failure. On the top part of each pillar, an sink node is placed to collect the sensed data. The sink nodes of each pillar become data gathering point of the LoWPAN hosts at the pillar as local coordinators.

This use case can be extended to medium or large size sensor networks to monitor a building or for instance the safety status of highways and tunnels. Larger networks of the same kind still have similar characteristics such as static node placement, manual deployment and dependent on the blue print of the structure, mesh topologies will be built with mains-powered relay points. Periodic and event-driven real-time data gathering is performed and the emergency event-driven data MUST be delivered without delay.

Dominant parameters in structural monitoring applications:



 TOC 

3.2.2.  6LoWPAN Applicability

The network configuration of this use case can be done by simple topologies, but there are many extended use cases for more complex structures. The example bridge monitoring case may be the simplest case.

The LoWPAN Nodes are installed on the place after manual optimization of their location. Static data paths to the data gathering points can be set in the commissioning phase. Address configuration and LoWPAN formation are acheived by 6LoWPAN HC [7] (Hui, J. and P. Thubert, “Compression Format for IPv6 Datagrams in 6LoWPAN Networks,” July 2010.) and 6LoWPAN ND [6] (Shelby, Z., Chakrabarti, S., and E. Nordmark, “Neighbor Discovery Optimization for Low-power and Lossy Networks,” July 2010.). Each pillar network may be built as a stub network, so that 16-bit addresses can be utilized (see Section 3 in [7] (Hui, J. and P. Thubert, “Compression Format for IPv6 Datagrams in 6LoWPAN Networks,” July 2010.)). Globally routable addresses must be allocated to communicate with other LoWPAN nodes.

If the network does not use a Route Over mechanism, the 6LoWPAN mesh-header described in RFC 4944 [4] (Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler, “Transmission of IPv6 Packets over IEEE 802.15.4 Networks,” September 2007.) may be used for static data forwarding, unless other mesh under mechanisms are provided.

Each pillar may have one LC for data collection from each pillar. The logical entity for data gathering can be implemented as a separate node or in a LR or LM. Communication schedules must be set up between leaf nodes and their LC to efficiently gather the different types of sensed data. Each data packet may include meta-information about its data, or the type of sensors could be encoded in its address during the address allocation. The data gathering entity can be programmed to trigger actuators installed in the infrastructure, when a certain threshold value has been reached. This type of application works based on both periodic and event-driven notifications. The data over or under a pre-defined threshold is meaningful to report. Event-driven data sensed on abnormal occurrences is time-critical and requires secure and reliable transmission. For energy conservation, all nodes may have periodic and long sleep modes but wake up on certain events.

Due to the safety-critical data of the structure, authentication and security are important issues here. Only authenticated users MUST be allowed to access the data. Additional security SHOULD be provided at the LBR for restricting the access from outside of the LoWPAN. The LBR may take charge of authentication of LoWPAN nodes. Reliable and secure data transmission should be guaranteed.



LBR - LC ----- LC ------ LC           LBR: LoWPAN Border Router
      /|        |        |            LC: Local Controller node
     n n    n - n - n    n - n        n: LoWPAN Node
       /\       |   |    |   |
      n  n      n - n    n - n - n

 Figure 3: A LoWPAN with a mesh topology 



 TOC 

3.3.  Connected Home

The "Connected" Home or "Smart" home is with no doubt an area where LoWPANs can be used to support an increasing number of services:

In home environments LoWPAN networks typically comprise a few dozen and probably in the near future a few hundreds of nodes of various nature: sensors, actuators and connected objects.



 TOC 

3.3.1.  A Use Case and its Requirements

Example: Home Automation

The home automation and control system LoWPAN offers a wide range of services: local or remote access from the Internet (via a secured edge router) to monitor the home (temperature, humidity, activation of remote video surveillance, status of the doors (locked or open), etc.) but also for home control (activate the air conditioning/heating, door locks, sprinkler systems, etc.). Fairly sophisticated systems can also optimize the level of energy consumption thanks to a wide range of input from various sensors connected to the LoWPAN: light sensors, presence detection, temperature, etc. in order to control electric window shades, chillers, air flow control, air conditioning and heating with the objective to optimize energy consumption.

With the emergence of “Smart Grid” applications, the LoWPAN may also have direct interactions with the Grid itself via the Internet of the Grid network to report the amount of KWatts that could be load shed (Home to Grid) and to receive dynamic load shedding information if/when required (Grid to home): this application is also referred to as Demand-Response application. Another service known as Demand Side Management (DSM) could be provided by utilities to monitor and report to the user its energy consumption with a fine granularity (on a per device basis). Other inputs such as dynamic pricing can also be received by the user from the utility that can then turn on and off some appliances according to its local policy in order to reduce its energy bill.

In terms of home safety and security, the LoWPAN is made of motion- and audio-sensors, sensors at doors and windows, and video cameras to which additional sensors can be added for safety (gas, water, CO, Radon, smoke detection). The LoWPAN typically comprises a few dozen of nodes forming an ad-hoc network with multi-hop routing since the nodes may not be in direct range. It is worth mentioning that the number of devices tends to grow considering the number of new applications for the home. In its most simple form, all nodes are static and communicate with a central control module but more sophisticated scenarios may also involve inter-device communication. For example, a motion/presence sensor may send a multicast message to a group of lights to be switched on, or a video camera will be activated sending a video stream to a gateway that can be received on a cell phone.

Ergonomics in Connected Homes is a key and the LoWPAN must be self-managed and easy to install. Traffic patterns may greatly vary depending on the applicability and so does the level of reliability and QoS expected from the LoWPAN. Humidity sensing is typically not critical and requires no immediate action whereas tele-assistance or gas leak detection is critical and requires a high degree of reliability. Furthermore, although some actions may not involve critical data, still the response time and network delays must be on the order of a few hundreds of milliseconds to preserve the user experience (e.g. use a remote control to switch a light on). A minority of nodes are mobile (with slow motion). With the emergence of energy related applications it becomes crucial to preserve data confidentiality. Connected Home LoWPAN usually do not require multi-topology or QoS routing and fairly simple QoS mechanisms must be supported by the LoWPAN (the number of Class of Services is usually limited).

Dominant parameters for home automation applications:



 TOC 

3.3.2.  6LoWPAN Applicability

In the home automation use case, the network topology is made of a mix of a battery operated and mains-powered nodes that both communication with each other and a LBR provides connectivities to the outside of LoWPAN for control management.

In home network, installation and management must as extremely simple for the user. Link local IPv6 addresses can be used by nodes with no external communication and the LBR allocates routable addresses to communicate with other LoWPAN nodes not reachable over a single radio transmission.




                           n --- n              I: Internet
                           |     |             LBR: LoWPAN Border Router
Internet/ ------- LBR/LC -- n --- n ---- LC     LC: Local controller node
Utility network     |      |            /|\     n: LoWPAN Node
                    n ---- n           n n n

   (outside)       (home automation system)

 Figure 4: Home Automation scenario 

In some scenarios, the traffic will be sent to a LC for processing that may in turn decide of local actions (switch a light on, …). In other scenarios, all devices will send their data to the LCs that may also act as the LBR for data processing and potential relay of data to outside of the LoWPAN. It does not mean that every device gets through the LC and LBR for communicating each other. For the sake of illustration, some of the data may be processed to trigger local action (e.g. switch off an appliance), simply store and sent once enough data has been accumulated (e.g. energy consumption for the past 6 hours for a set of appliances) or could trigger an alarm immediately sent to a datacenter (e.g. gas leak detection).

Although in the majority of cases nodes within the LoPWAN will be in direct range, some nodes will reach the LBR/LC with a 2-3 hops path using Mesh Under or very likely a Route Over solution (with the emergence of several low power media such as low power PLC) in which case LoWPAN routers will be deployed in the home to interconnect the various IPv6 links.

The home LoWPAN must be able to provide extremely reliable communication in support of some specific application (e.g. fire, gas leak detection, health monitoring) whereas other application may not be critical at all (e.g humidity monitoring). Similarly some information may require the use of security mechanisms for authentication, confidentiality.



 TOC 

3.4.  Healthcare

LoWPANs are envisioned to be heavily used in healthcare environments. They have a big potential to ease the deployment of new services by getting rid of cumbersome wires and simplify patient care in hospitals and for home care. In healthcare environments, delayed or lost information may be a matter of life or death.

Various systems, ranging from simple wearable remote controls for tele-assistance or intermediate systems with wearable sensor nodes monitoring various metrics to more complex systems for studying life dynamics, can be supported by LoWPANs. In the latter category, a large amount of data from various LoWPAN nodes can be collected: movement pattern observation, checks that medicaments have been taken, object tracking, and more. An example of such a deployment is described in [10] (den Hartog, F., Schmidt, J., and A. de Vries, “On the Potential of Personal Networks for Hospitals,” May 2006.) using the concept of Personal Networks.



 TOC 

3.4.1.  A Use Case and its Requirements

Example: healthcare at home by tele-assistance

A senior citizen who lives alone wears one to few wearable LoWPAN nodes to measure heartbeat, pulse rate, etc. Dozens of LoWPAN nodes are densely installed at home for movement detection. A LBR at home will send the sensed information to a connected healthcare center. Portable base stations with LCDs may be used to check the data at home, as well. The different roles of devices have different duty-cycles, which affect node management.

Multipath interference may often occur due to the mobility of the patients at home, where there are many walls and obstacles. Even during sleeping, the change of the body position may affect the radio propagation.

Data is gathered both periodically and event-driven. In this application, event-driven data can be very time-critical. Thus, real-time and reliable transmission must be guaranteed.

Privacy also becomes an serious issue in this case, as the sensed data is very personal. In addition, different data will be provided to the hospital system from what is given to a patient's family members. Role-based access control is needed to support such services, thus support of authorization and authentication is important.

Dominant parameters in healthcare applications:



 TOC 

3.4.2.  6LoWPAN Applicability

In this use case, the local network size is rather small (less than 10s of nodes). The home care system is statically configured with multi-hop paths and the patient’s body network can be built as a star topology. The LBR at home is the sink node in the routing path from sources on the patient's body. A plug-and-play configuration is required. As the communication of the system is limited to a home environment, both 16-bit and 64-bit can be used for IPv6 link-local addresses [4] (Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler, “Transmission of IPv6 Packets over IEEE 802.15.4 Networks,” September 2007.). An example topology is provided in Figure 5 (A mobile healthcare scenario.).

Multi-hop communication can be achieved by either Mesh Under or Route Over mechanisms. When a Route Over routing mechanism is used, the routers deployed in the home environment will form a mesh of IPv6 links. In Mesh Under, more than one LMs in the LoWPAN play role in multi-hop transmission in link layer and in transmission multi-point traffic (multicast) to unicast method. In Route Over, LRs will handle multicast traffic to their LoWPAN link.

The patient’s body network can be simply configured as a star topology with a LC dealing with data aggregation and dynamic network attachment when the patient moves around at home. As multipath interference may often occur due to the patients' mobility at home, the deployment of LoWPAN nodes and transmission paths should be well considered. At home, some nodes can be installed with power-affluence status, and those LoWPAN nodes can be used for relaying points or data aggregation points.

The sensed information MUST be maintained with the identification of the patient no matter if the patient visits the connected hospital or stays at home. If the patient's LoWPAN uses globally unique IPv6 address, the address can be used for the identification. However, it causes cost for privacy and security. The hospital LoWPAN where the patient's information is transferring needs to operate additional identification system together with strong authority and athentication mechanism. The connection between the LBR at home and the LBR at Hospital must be reliable and secure, as the data is privacy-critical. To achieve this, additional policy for security is recommended between the two LoWPAN.



                      n - n               I: Internet
                      |   |             LBR: Edge Router
   LBR --- I -- LBR - n - n - LC         LC: Local controller node
   /|\           |    |       /|\         n: LoWPAN Node
 .. . ..         n -- n      n n n

(hospital)       (home system)  (patient)

 Figure 5: A mobile healthcare scenario. 



 TOC 

3.5.  Vehicle Telematics

LoWPANs play an important role in intelligent transportation systems. Incorporated in roads, vehicles, and traffic signals, they contribute to the improvement of safety of transporting systems. Through traffic or air-quality monitoring, they increase the possibilities in terms of traffic flow optimization and help reducing road congestion.



 TOC 

3.5.1.  A Use Case and its Requirements

Example: Telematics

As shown in Figure 6 (Multi-hop LoWPAN combined with mobile star LoWPAN.), scattered LoWPAN Nodes are included in roads during their construction for motion monitoring. When a car passes over these nodes, the possibility is then given to track the trajectory and velocity of cars for safety purposes. The lifetime of the LoWPAN Nodes incorporated into roads is expected to be as long as the life time of the roads (about 10 years). Multihop communication is possible between LoWPAN Nodes, and the network should be able to cope with the deterioration over time of the node density due to power failures. Sink nodes placed at the side of road are mains-powered, LoWPAN Nodes in the roads run on battery. Power savings schemes might intermittently disconnect the nodes. A rough estimate of 4 nodes per square meter is needed. Other applications may involve car-to-car communication for increased road safety.

Dominant parameters in vehicle telematics applications:



 TOC 

3.5.2.  6LoWPAN Applicability

For this use case, the network topology includes fixed LBRs that are mains-powered and have a connection to high speed networks (e.g., Internet) in order to reach the transportation control center. These LBRs may be logically combined with LC as a data sink to gather sensed data from a number of LoWPAN Nodes inserted in the tarmac of the road.

In the road infrastructure, a LoWPAN with one LBR forms a fixed network and the LoWPAN nodes are installed by manual optimization of their location. Static data paths to the data gathering point can be set in the commissioning phase. If the network does not use a Route Over mechanism, the 6LoWPAN mesh under forwarding is used. Forwarding/Routing tables are not changed unless a node failure occurs.



	+-----+
	| LBR |----------------------------- LBR ...
	+-----+    (at the road side)
 -------|------------------------------
		|
   n -- n --- n --- n   +---|---+       LBR: LoWPAN Border Router
       / \          |   | n-n-n |        n: LoWPAN Node
      n  n          n   +---|---+
                          (cars)
 --------------------------------------

 Figure 6: Multi-hop LoWPAN combined with mobile star LoWPAN. 



 TOC 

3.6.  Agricultural Monitoring

Accurate temporal and spatial monitoring can significantly increase agricultural productivity. Due to natural limitations, such as a farmers' inability to check the crop at all times of day or inadequate measurement tools, luck often plays a too large role in the success of harvests. Using a network of strategically placed sensors, indicators such as temperature, humidity, soil condition, can be automatically monitored without labor intensive field measurements. For example, sensor networks could provide precise information about crops in real time, enabling businesses to reduce water, energy, and pesticide usage and enhancing environment protection. The sensing data can be used to find optimal environments for the plants. In addition, the data on the planting condition can be saved by sensor tags, which can be used in supply chain management.



 TOC 

3.6.1.  A Use Case and its Requirements

Example: Automated Vineyard

In a vineyard with medium to large geographical size, a number of 50 to 100 LC nodes are manually deployed in order to provide full signal coverage over the study area. An additional number of 100 to 1000 leaf nodes with (possibly heterogeneous) specialized sensors (i.e., humidity, temperature, soil condition, sunlight) are attached to the LCs in local wireless star topologies, periodically reporting measurements to the associated LCs. For example, in a 20-acre vineyard with 8 parcels of land, 10 LoWPAN Nodes are placed within each parcel to provide readings on temperature and soil moisture. The LoWPAN Nodes are able to support a multi-hop forwarding/routing scheme to enable data transmission to a sink node at the edge of the vineyard. Each of the 8 parcels contains one data aggregator to collect the sensed data.

Localization is important for this type of LoWPAN where installed in a geographically large area, for pinning down where an event occurred, and for combining gathered data with their actual position. Using manual deployment, device addresses can be used for identifying the position and localization. For randomly deployed nodes, a localization algorithm needs to be applied.

There might be various types of sensor devices deployed in a single LoWPAN, each providing raw data with different semantics. Thus, an additional method is required to correctly interpret sensor readings. Each data packet may include meta-information about its data, or a type of a sensor could be encoded in its address during address allocation.

Dominant parameters in agricultural monitoring:



 TOC 

3.6.2.  6LoWPAN Applicability

The network configuration in this use case might, in the most simple case, look like illustrated in Figure 7 (An aligned multi-hop LoWPAN.). This static scenario consists of one or more fixed LBR that are mains-powered and have a high-bandwidth connection to a backbone link, which might be placed in a control center, or connect to the Internet. The LBRs are strategically located at the border of vineyard parcels, acting as data sinks. A number of LCs are placed along a row of plants with individual LoWPAN nodes spread around them.

While the LBRs implement the IPv6 Neighbor Discovery protocol (RFC 4861) to connect the outside of the LoWPAN, the LoWPAN Nodes operate a more energy-considering ND described in [6] (Shelby, Z., Chakrabarti, S., and E. Nordmark, “Neighbor Discovery Optimization for Low-power and Lossy Networks,” July 2010.), which includes basic bootstrapping and address assignment. Each LBR can have predefined forward management information to a central data aggregation point, if necessary.

The intermediate nodes must implement a multi-hop forwarding/routing protocol and they are responsible to transmit the measured data at the LoWPAN nodes to the LBRs. In this simplest case, the LRs or LMs can build static forwarding/routing paths, and all end-nodes can be placed in one radio hop distance from its forwarder. In more advanced setups, mesh routing is used for data distribution.

LoWPAN nodes may send event-driven notifications when readings exceed certain thresholds, such as low soil humidity; which may automatically trigger a water sprinkler in the local environment. For increased energy efficiency, all LoWPAN Nodes are in periodic sleep state. However, the LCs need to be aware of sudden events from the leaf nodes. Their sleep periods should therefore be set to shorter intervals. Communication schedules must be set up between master and leaf nodes, and global time synchronization is needed to account for clock drift.

Also, the result of data collection may activate actuators. Context-awareness, node identification and data collection on the application level are necessary.



     I
     |
     |    n n n   n n n   n n n         I: Internet
     |     \|/     \|/     \|/        LBR: LoWPAN Border Router
    LBR----LC------LC------LC          LC: Local Controller node
     |     /|\     /|\     /|\          n: LoWPAN node
     |    n n n   n n n   n n n
     |
LBR
    ...

 Figure 7: An aligned multi-hop LoWPAN. 



 TOC 

4.  Security Considerations

Security requirements differ by use case. For example, industrial and structural monitoring applications are safety-critical. Secure transmission MUST be guaranteed, and only authenticated users MUST be able to access and handle the data. Lightweight key mechanisms can be used. In health care system, data privacy is an important issue. Encryption is required, and role-based access control is required to be supported by a proper authentication mechanism.



 TOC 

5.  Acknowledgements

Thanks to David Cypher for giving more insight on the IEEE 802.15.4 standard and to Irene Fernandez for her review and valuable comments.



 TOC 

6.  References



 TOC 

6.1. Normative References

[1] Bradner, S., “Key words for use in RFCs to Indicate Requirement Levels,” BCP 14, RFC 2119, March 1997 (TXT, HTML, XML).
[2] Narten, T., Nordmark, E., Simpson, W., and H. Soliman, “Neighbor Discovery for IP version 6 (IPv6),” RFC 4861, September 2007 (TXT).
[3] Kushalnagar, N., Montenegro, G., and C. Schumacher, “IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs): Overview, Assumptions, Problem Statement, and Goals,” RFC 4919, August 2007 (TXT).
[4] Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler, “Transmission of IPv6 Packets over IEEE 802.15.4 Networks,” RFC 4944, September 2007 (TXT).
[5] IEEE Computer Society, “IEEE Std. 802.15.4-2006 (as amended),” 2007.


 TOC 

6.2. Informative References

[6] Shelby, Z., Chakrabarti, S., and E. Nordmark, “Neighbor Discovery Optimization for Low-power and Lossy Networks,” draft-ietf-6lowpan-nd-11 (work in progress), July 2010 (TXT).
[7] Hui, J. and P. Thubert, “Compression Format for IPv6 Datagrams in 6LoWPAN Networks,” draft-ietf-6lowpan-hc-08 (work in progress), July 2010 (TXT).
[8] Kim, E., Kaspar, D., Gomez, C., and C. Bormann, “Problem Statement and Requirements for 6LoWPAN Routing,” draft-ietf-6lowpan-routing-requirements-06 (work in progress), March 2010 (TXT).
[9] Roemer, K. and F. Mattern, “The Design Space of Wireless Sensor Networks,” December 2004.
[10] den Hartog, F., Schmidt, J., and A. de Vries, “On the Potential of Personal Networks for Hospitals,” May 2006.


 TOC 

Authors' Addresses

  Eunsook Kim
  ETRI
  161 Gajeong-dong
  Yuseong-gu
  Daejeon 305-700
  Korea
Phone:  +82-42-860-6124
Email:  eunah.ietf@gmail.com
  
  Dominik Kaspar
  Simula Research Laboratory
  Martin Linges v 17
  Snaroya 1367
  Norway
Phone:  +47-4748-9307
Email:  dokaspar.ietf@gmail.com
  
  Nicolas G. Chevrollier
  TNO
  Brassersplein 2
  P.O. Box 5050
  Delft 2600
  The Netherlands
Phone:  +31-15-285-7354
Email:  nicolas.chevrollier@tno.nl
  
  JP Vasseur
  Cisco Systems, Inc
  1414 Massachusetts Avenue
  Boxborough MA 01719
  USA
Phone: 
Email:  jpv@cisco.com