Internet Engineering Task Force E. Jankiewicz Internet-Draft SRI International, Inc. Obsoletes: 4294 (if approved) J. Loughney Intended status: Informational Nokia Expires: November 24, 2011 T. Narten IBM Corporation May 23, 2011 IPv6 Node Requirements draft-ietf-6man-node-req-bis-10.txt Abstract This document defines requirements for IPv6 nodes. It is expected that IPv6 will be deployed in a wide range of devices and situations. Specifying the requirements for IPv6 nodes allows IPv6 to function well and interoperate in a large number of situations and deployments. This document obsoletes RFC4294. Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on November 24, 2011. Copyright Notice Copyright (c) 2011 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents Jankiewicz, et al. Expires November 24, 2011 [Page 1] Internet-Draft IPv6 Node Requirements May 2011 carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. This document may contain material from IETF Documents or IETF Contributions published or made publicly available before November 10, 2008. The person(s) controlling the copyright in some of this material may not have granted the IETF Trust the right to allow modifications of such material outside the IETF Standards Process. Without obtaining an adequate license from the person(s) controlling the copyright in such materials, this document may not be modified outside the IETF Standards Process, and derivative works of it may not be created outside the IETF Standards Process, except to format it for publication as an RFC or to translate it into languages other than English. Jankiewicz, et al. Expires November 24, 2011 [Page 2] Internet-Draft IPv6 Node Requirements May 2011 Table of Contents 1. Requirements Language . . . . . . . . . . . . . . . . . . . . 5 2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1. Scope of This Document . . . . . . . . . . . . . . . . . . 6 2.2. Description of IPv6 Nodes . . . . . . . . . . . . . . . . 6 3. Abbreviations Used in This Document . . . . . . . . . . . . . 6 4. Sub-IP Layer . . . . . . . . . . . . . . . . . . . . . . . . . 7 5. IP Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5.1. Internet Protocol Version 6 - RFC 2460 . . . . . . . . . . 8 5.2. Neighbor Discovery for IPv6 - RFC 4861 . . . . . . . . . . 8 5.3. Default Router Preferences and More-Specific Routes - RFC 4191 . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.4. SEcure Neighbor Discovery (SEND) - RFC 3971 . . . . . . . 10 5.5. IPv6 Router Advertisement Flags Option - RFC 5175 . . . . 10 5.6. Path MTU Discovery and Packet Size . . . . . . . . . . . . 10 5.6.1. Path MTU Discovery - RFC 1981 . . . . . . . . . . . . 10 5.7. IPv6 Jumbograms - RFC 2675 . . . . . . . . . . . . . . . . 11 5.8. ICMP for the Internet Protocol Version 6 (IPv6) - RFC 4443 . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5.9. Addressing . . . . . . . . . . . . . . . . . . . . . . . . 11 5.9.1. IP Version 6 Addressing Architecture - RFC 4291 . . . 11 5.9.2. IPv6 Stateless Address Autoconfiguration - RFC 4862 . 11 5.9.3. Privacy Extensions for Address Configuration in IPv6 - RFC 4941 . . . . . . . . . . . . . . . . . . . 12 5.9.4. Default Address Selection for IPv6 - RFC 3484 . . . . 12 5.9.5. Stateful Address Autoconfiguration - RFC 3315 . . . . 13 5.10. Multicast Listener Discovery (MLD) for IPv6 . . . . . . . 13 6. DHCP vs. Router Advertisement Options for Host Configuration . . . . . . . . . . . . . . . . . . . . . . . . 14 7. DNS and DHCP . . . . . . . . . . . . . . . . . . . . . . . . . 15 7.1. DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 7.2. Dynamic Host Configuration Protocol for IPv6 (DHCPv6) - RFC 3315 . . . . . . . . . . . . . . . . . . . . . . . . 15 7.2.1. Other Configuration Information . . . . . . . . . . . 15 7.2.2. Use of Router Advertisements in Managed Environments . . . . . . . . . . . . . . . . . . . . . 15 7.3. IPv6 Router Advertisement Options for DNS Configuration - RFC 6106 . . . . . . . . . . . . . . . . . 15 8. IPv4 Support and Transition . . . . . . . . . . . . . . . . . 16 8.1. Transition Mechanisms . . . . . . . . . . . . . . . . . . 16 8.1.1. Basic Transition Mechanisms for IPv6 Hosts and Routers - RFC 4213 . . . . . . . . . . . . . . . . . . 16 9. Application Support . . . . . . . . . . . . . . . . . . . . . 16 9.1. Textual Representation of IPv6 Addresses - RFC 5952 . . . 16 9.2. Application Program Interfaces (APIs) . . . . . . . . . . 16 10. Mobility . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 11. Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Jankiewicz, et al. Expires November 24, 2011 [Page 3] Internet-Draft IPv6 Node Requirements May 2011 11.1. Requirements . . . . . . . . . . . . . . . . . . . . . . . 18 11.2. Transforms and Algorithms . . . . . . . . . . . . . . . . 19 12. Router-Specific Functionality . . . . . . . . . . . . . . . . 19 12.1. General . . . . . . . . . . . . . . . . . . . . . . . . . 19 12.1.1. IPv6 Router Alert Option - RFC 2711 . . . . . . . . . 19 12.1.2. Neighbor Discovery for IPv6 - RFC 4861 . . . . . . . . 19 13. Network Management . . . . . . . . . . . . . . . . . . . . . . 19 13.1. Management Information Base Modules (MIBs) . . . . . . . . 20 13.1.1. IP Forwarding Table MIB . . . . . . . . . . . . . . . 20 13.1.2. Management Information Base for the Internet Protocol (IP) . . . . . . . . . . . . . . . . . . . . 20 14. Security Considerations . . . . . . . . . . . . . . . . . . . 20 15. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 20 16. Authors and Acknowledgments . . . . . . . . . . . . . . . . . 20 16.1. Authors and Acknowledgments (Current Document) . . . . . . 20 16.2. Authors and Acknowledgments From RFC 4279 . . . . . . . . 20 17. Appendix: Changes from One ID version to Another . . . . . . . 21 17.1. Appendix: Changes from -09 to -10 . . . . . . . . . . . . 21 17.2. Appendix: Changes from -08 to -09 . . . . . . . . . . . . 22 17.3. Appendix: Changes from -07 to -08 . . . . . . . . . . . . 22 17.4. Appendix: Changes from -06 to -07 . . . . . . . . . . . . 22 17.5. Appendix: Changes from -05 to -06 . . . . . . . . . . . . 23 17.6. Appendix: Changes from -04 to -05 . . . . . . . . . . . . 23 17.7. Appendix: Changes from -03 to -04 . . . . . . . . . . . . 23 18. Appendix: Changes from RFC 4294 . . . . . . . . . . . . . . . 23 19. References . . . . . . . . . . . . . . . . . . . . . . . . . . 24 19.1. Normative References . . . . . . . . . . . . . . . . . . . 24 19.2. Informative References . . . . . . . . . . . . . . . . . . 27 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 30 Jankiewicz, et al. Expires November 24, 2011 [Page 4] Internet-Draft IPv6 Node Requirements May 2011 1. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. 2. Introduction This document defines common functionality required from both IPv6 hosts and routers. Many IPv6 nodes will implement optional or additional features, but this document collects and summarizes requirements from other published Standards Track documents in one place. This document tries to avoid discussion of protocol details, and references RFCs for this purpose. This document is intended to be an Applicability Statement and provide guidance as to which IPv6 specifications should be implemented in the general case, and which specification may be of interest to specific deployment scenarios. This document does not update any individual protocol document RFCs. Although the document points to different specifications, it should be noted that in many cases, the granularity of a particular requirement will be smaller than a single specification, as many specifications define multiple, independent pieces, some of which may not be mandatory. In addition, most specifications define both client and server behavior in the same specification, while many implementations will be focused on only one of those roles. This document defines a minimal level of requirement needed for a device to provide useful internet service and considers a broad range of device types and deployment scenarios. Because of the wide range of deployment scenarios, the minimal requirements specified in this document may not be sufficient for all deployment scenarios. It is perfectly reasonable (and indeed expected) for other profiles to define additional or stricter requirements appropriate for specific usage and deployment environments. For example, this document does not mandate that all clients support DHCP, but some deployment scenarios may deem it appropriate to make such a requirement. For example, government agencies in the USA have defined profiles for specialized requirements for IPv6 in target environments [DODv6] and [USGv6]. As it is not always possible for an implementer to know the exact usage of IPv6 in a node, an overriding requirement for IPv6 nodes is that they should adhere to Jon Postel's Robustness Principle: Jankiewicz, et al. Expires November 24, 2011 [Page 5] Internet-Draft IPv6 Node Requirements May 2011 Be conservative in what you do, be liberal in what you accept from others [RFC0793]. 2.1. Scope of This Document IPv6 covers many specifications. It is intended that IPv6 will be deployed in many different situations and environments. Therefore, it is important to develop the requirements for IPv6 nodes to ensure interoperability. This document assumes that all IPv6 nodes meet the minimum requirements specified here. 2.2. Description of IPv6 Nodes From the Internet Protocol, Version 6 (IPv6) Specification [RFC2460], we have the following definitions: Description of an IPv6 Node - a device that implements IPv6. Description of an IPv6 router - a node that forwards IPv6 packets not explicitly addressed to itself. Description of an IPv6 Host - any node that is not a router. 3. Abbreviations Used in This Document ATM Asynchronous Transfer Mode AH Authentication Header DAD Duplicate Address Detection ESP Encapsulating Security Payload ICMP Internet Control Message Protocol IKE Internet Key Exchange MIB Management Information Base MLD Multicast Listener Discovery MTU Maximum Transfer Unit NA Neighbor Advertisement Jankiewicz, et al. Expires November 24, 2011 [Page 6] Internet-Draft IPv6 Node Requirements May 2011 NBMA Non-Broadcast Multiple Access ND Neighbor Discovery NS Neighbor Solicitation NUD Neighbor Unreachability Detection PPP Point-to-Point Protocol PVC Permanent Virtual Circuit SVC Switched Virtual Circuit 4. Sub-IP Layer An IPv6 node must include support for one or more IPv6 link-layer specifications. Which link-layer specifications an implementation should include will depend upon what link-layers are supported by the hardware available on the system. It is possible for a conformant IPv6 node to support IPv6 on some of its interfaces and not on others. As IPv6 is run over new layer 2 technologies, it is expected that new specifications will be issued. In the following, we list some of the link-layers for which an IPv6 specification has been developed. It is provided for information purposes only, and may not be complete. - Transmission of IPv6 Packets over Ethernet Networks [RFC2464] - IPv6 over ATM Networks [RFC2492] - Transmission of IPv6 Packets over Frame Relay Networks Specification [RFC2590] - Transmission of IPv6 Packets over IEEE 1394 Networks [RFC3146] - Transmission of IPv6, IPv4, and Address Resolution Protocol (ARP) Packets over Fibre Channel [RFC4338] - Transmission of IPv6 Packets over IEEE 802.15.4 Networks [RFC4944] - Transmission of IPv6 via the IPv6 Convergence Sublayer over IEEE 802.16 Networks [RFC5121] - IP version 6 over PPP [RFC5072] In addition to traditional physical link-layers, it is also possible to tunnel IPv6 over other protocols. Examples include: - Teredo: Tunneling IPv6 over UDP through Network Address Translations (NATs) [RFC4380] - Section 3 of "Basic IPv6 Transition Mechanisms" [RFC4213] 5. IP Layer Jankiewicz, et al. Expires November 24, 2011 [Page 7] Internet-Draft IPv6 Node Requirements May 2011 5.1. Internet Protocol Version 6 - RFC 2460 The Internet Protocol Version 6 is specified in [RFC2460]. This specification MUST be supported. Any unrecognized extension headers or options MUST be processed as described in RFC 2460. The node MUST follow the packet transmission rules in RFC 2460. Nodes MUST always be able to send, receive, and process fragment headers. All conformant IPv6 implementations MUST be capable of sending and receiving IPv6 packets; the forwarding functionality MAY be supported. Overlapping fragments MUST be handled as described in [RFC5722]. RFC 2460 specifies extension headers and the processing for these headers. An IPv6 node MUST be able to process these headers. An exception is Routing Header type 0 (RH0) which was deprecated by [RFC5095] due to security concerns, and which MUST be treated as an unrecognized routing type. 5.2. Neighbor Discovery for IPv6 - RFC 4861 Neighbor Discovery is defined in [RFC4861] and was updated by [RFC5942]. Neighbor Discovery SHOULD be supported. RFC4861 states: Unless specified otherwise (in a document that covers operating IP over a particular link type) this document applies to all link types. However, because ND uses link-layer multicast for some of its services, it is possible that on some link types (e.g., NBMA links) alternative protocols or mechanisms to implement those services will be specified (in the appropriate document covering the operation of IP over a particular link type). The services described in this document that are not directly dependent on multicast, such as Redirects, Next-hop determination, Neighbor Unreachability Detection, etc., are expected to be provided as specified in this document. The details of how one uses ND on NBMA links is an area for further study. Some detailed analysis of Neighbor Discovery follows: Router Discovery is how hosts locate routers that reside on an attached link. Hosts MUST support Router Discovery functionality. Prefix Discovery is how hosts discover the set of address prefixes Jankiewicz, et al. Expires November 24, 2011 [Page 8] Internet-Draft IPv6 Node Requirements May 2011 that define which destinations are on-link for an attached link. Hosts MUST support Prefix discovery. Hosts MUST also implement Neighbor Unreachability Detection (NUD) for all paths between hosts and neighboring nodes. NUD is not required for paths between routers. However, all nodes MUST respond to unicast Neighbor Solicitation (NS) messages. Hosts MUST support the sending of Router Solicitations and the receiving of Router Advertisements. The ability to understand individual Router Advertisement options is dependent on supporting the functionality making use of the particular option. All nodes MUST support the Sending and Receiving of Neighbor Solicitation (NS) and Neighbor Advertisement (NA) messages. NS and NA messages are required for Duplicate Address Detection (DAD). Hosts SHOULD support the processing of Redirect functionality. Routers MUST support the sending of Redirects, though not necessarily for every individual packet (e.g., due to rate limiting). Redirects are only useful on networks supporting hosts. In core networks dominated by routers, redirects are typically disabled. The sending of redirects SHOULD be disabled by default on backbone routers. They MAY be enabled by default on routers intended to support hosts on edge networks. "IPv6 Host-to-Router Load Sharing" [RFC4311] includes additional recommendations on how to select from a set of available routers. RFC 4311 SHOULD be supported. 5.3. Default Router Preferences and More-Specific Routes - RFC 4191 "Default Router Preferences and More-Specific Routes" [RFC4191] provides support for nodes attached to multiple (different) networks each providing routers that advertise themselves as default routers via Router Advertisements. In some scenarios, one router may provide connectivity to destinations the other router does not and choosing the "wrong" default router can result in reachability failures. In such cases, RFC4191 can help. Small Office/Home Office (SOHO) deployments supported by routers adhering to [RFC6204], use [RFC4191] to advertise routes to certain local destinations. Consequently, nodes that will be deployed in SOHO environments SHOULD implement [RFC4191]. Jankiewicz, et al. Expires November 24, 2011 [Page 9] Internet-Draft IPv6 Node Requirements May 2011 5.4. SEcure Neighbor Discovery (SEND) - RFC 3971 SEND [RFC3971] and Cryptographically Generated Address (CGA) [RFC3972] provide a way to secure the message exchanges of Neighbor Discovery. SEND is a new technology, in that it has no IPv4 counterpart but it has significant potential to address certain classes of spoofing attacks. While there have been some implementations of SEND, there has been only limited deployment experience to date in using the technology. In addition, the IETF working group Cga & Send maIntenance (csi) is currently working on additional extensions intended to make SEND more attractive for deployment. At this time, SEND is considered optional and IPv6 nodes MAY provide SEND functionality. 5.5. IPv6 Router Advertisement Flags Option - RFC 5175 Router Advertisements include an 8-bit field of single-bit Router Advertisement flags. The Router Advertisement Flags Option extends the number of available flag bits by 48 bits. At the time of this writing, 6 of the original 8 bit flags have been assigned, while 2 remain available for future assignment. No flags have been defined that make use of the new option, and thus strictly speaking, there is no requirement to implement the option today. However, implementations that are able to pass unrecognized options to a higher level entity that may be able to understand them (e.g., a user-level process using a "raw socket" facility), MAY take steps to handle the option in anticipation of a future usage. 5.6. Path MTU Discovery and Packet Size 5.6.1. Path MTU Discovery - RFC 1981 "Path MTU Discovery" [RFC1981] SHOULD be supported. From [RFC2460]: It is strongly recommended that IPv6 nodes implement Path MTU Discovery [RFC1981], in order to discover and take advantage of path MTUs greater than 1280 octets. However, a minimal IPv6 implementation (e.g., in a boot ROM) may simply restrict itself to sending packets no larger than 1280 octets, and omit implementation of Path MTU Discovery. The rules in [RFC2460] and [RFC5722] MUST be followed for packet fragmentation and reassembly. One operational issue with Path MTU discovery occurs when firewalls block ICMP Packet Too Big messages. Path MTU discovery relies on Jankiewicz, et al. Expires November 24, 2011 [Page 10] Internet-Draft IPv6 Node Requirements May 2011 such messages to determine what size messages can be successfully sent. Packetization Layer Path MTU Discovery [RFC4821] avoids having a dependency on Packet Too Big messages. 5.7. IPv6 Jumbograms - RFC 2675 IPv6 Jumbograms [RFC2675] are an optional extension that allow the sending of IP datagrams larger than 65.535 bytes. IPv6 Jumbograms make use of IPv6 hop-by-hop options and are only suitable on paths in which every hop and link are capable of supporting Jumbograms (e.g., within a campus or datacenter). To date, few implementations exist and there is essentially no reported experience from usage. Consequently, IPv6 Jumbograms [RFC2675] remain optional at this time. 5.8. ICMP for the Internet Protocol Version 6 (IPv6) - RFC 4443 ICMPv6 [RFC4443] MUST be supported. "Extended ICMP to Support Multi- Part Messages" [RFC4884] MAY be supported. 5.9. Addressing 5.9.1. IP Version 6 Addressing Architecture - RFC 4291 The IPv6 Addressing Architecture [RFC4291] MUST be supported. 5.9.2. IPv6 Stateless Address Autoconfiguration - RFC 4862 Hosts MUST support IPv6 Stateless Address Autoconfiguration as defined in [RFC4862]. Static address may be supported as well. Nodes that are routers MUST be able to generate link local addresses as described in RFC 4862 [RFC4862]. From 4862: The autoconfiguration process specified in this document applies only to hosts and not routers. Since host autoconfiguration uses information advertised by routers, routers will need to be configured by some other means. However, it is expected that routers will generate link-local addresses using the mechanism described in this document. In addition, routers are expected to successfully pass the Duplicate Address Detection procedure described in this document on all addresses prior to assigning them to an interface. All nodes MUST implement Duplicate Address Detection. Quoting from Section 5.4 of RFC 4862: Jankiewicz, et al. Expires November 24, 2011 [Page 11] Internet-Draft IPv6 Node Requirements May 2011 Duplicate Address Detection MUST be performed on all unicast addresses prior to assigning them to an interface, regardless of whether they are obtained through stateless autoconfiguration, DHCPv6, or manual configuration, with the following [exceptions noted therein]. "Optimistic Duplicate Address Detection (DAD) for IPv6" [RFC4429] specifies a mechanism to reduce delays associated with generating addresses via stateless address autoconfiguration [RFC4862]. RFC 4429 was developed in conjunction with Mobile IPv6 in order to reduce the time needed to acquire and configure addresses as devices quickly move from one network to another, and it is desirable to minimize transition delays. For general purpose devices, RFC 4429 is not considered to be necessary at this time. 5.9.3. Privacy Extensions for Address Configuration in IPv6 - RFC 4941 Privacy Extensions for Stateless Address Autoconfiguration [RFC4941] addresses a specific problem involving a client device whose user is concerned about its activity or location being tracked. The problem arises both for a static client and for one that regularly changes its point of attachment to the Internet. When using Stateless Address Autoconfiguration [RFC4862], the Interface Identifier portion of formed addresses stays constant and is globally unique. Thus, although a node's global IPv6 address will change if it changes its point of attachment, the Interface Identifier portion of those addresses remain the same, making it possible for servers to track the location of an individual device as it moves around, or its pattern of activity if it remains in one place. This may raise privacy concerns as described in [RFC4862]. In such situations, RFC4941 SHOULD be implemented. In other cases, such as with dedicated servers in a data center, RFC4941 provides limited or no benefit. Implementers of "RFC4941 should be aware that certain addresses are reserved and should not be chosen for use as temporary addresses. Consult "Reserved IPv6 Interface Identifiers" [RFC5453] for more details. 5.9.4. Default Address Selection for IPv6 - RFC 3484 The rules specified in the Default Address Selection for IPv6 [RFC3484] document MUST be implemented. IPv6 nodes will need to deal with multiple addresses configured simultaneously. Jankiewicz, et al. Expires November 24, 2011 [Page 12] Internet-Draft IPv6 Node Requirements May 2011 5.9.5. Stateful Address Autoconfiguration - RFC 3315 DHCPv6 [RFC3315] can be used to obtain and configure addresses. In general, a network may provide for the configuration of addresses through Router Advertisements, DHCPv6 or both. There will be a wide range of IPv6 deployment models and differences in address assignment requirements, some of which may require DHCPv6 for address assignment. Consequently all hosts SHOULD implement address configuration via DHCPv6. In the absence of a router, IPv6 nodes using DHCP for address assignment MAY initiate DHCP to obtain IPv6 addresses and other configuration information, as described in Section 5.5.2 of [RFC4862]. 5.10. Multicast Listener Discovery (MLD) for IPv6 Nodes that need to join multicast groups MUST support MLDv1 [RFC2710]. MLDv1 is needed by any node that is expected to receive and process multicast traffic. Note that Neighbor Discovery (as used on most link types -- see Section 5.2) depends on multicast and requires that nodes join Solicited Node multicast addresses. MLDv2 [RFC3810] extends the functionality of MLDv1 by supporting Source-Specific Multicast. The original MLDv2 protocol [RFC3810] supporting Source-Specific Multicast [RFC4607] supports two types of "filter modes". Using an INCLUDE filter, a node indicates a multicast group along with a list of senders for that group it wishes to receive traffic from. Using an EXCLUDE filter, a node indicates a multicast group along with a list of senders it wishes to exclude receiving traffic from. In practice, operations to block source(s) using EXCLUDE mode are rarely used, but add considerable implementation complexity to MLDv2. Lightweight MLDv2 [RFC5790] is a simplified subset of the original MLDv2 specification that omits EXCLUDE filter mode to specify undesired source(s). Nodes SHOULD implement either MLDv2 [RFC3810] or Lightweight MLDv2 [RFC5790]. Specifically, nodes supporting applications using Source- Specific Multicast that expect to take advantage of MLDv2's EXCLUDE functionality [RFC3810] MUST support MLDv2 as defined in [RFC3810], [RFC4604] and [RFC4607]. Nodes supporting applications that expect to only take advantage of MLDv2's INCLUDE functionality as well as Any-Source Multicast will find it sufficient to support MLDv2 as defined in [RFC5790]. If a node only supports applications that use Any-Source Multicast (i.e, they do not use source-specific multicast), implementing MLDv1 [RFC2710] is sufficient. In all cases, however, nodes are strongly Jankiewicz, et al. Expires November 24, 2011 [Page 13] Internet-Draft IPv6 Node Requirements May 2011 encouraged to implement MLDv2 or Lightweight MLDv2 rather than MLDv1, as the presence of a single MLDv1 participant on a link requires that all other nodes on the link operate in version 1 compatibility mode. When MLDv1 is used, the rules in the Source Address Selection for the Multicast Listener Discovery (MLD) Protocol [RFC3590] MUST be followed. 6. DHCP vs. Router Advertisement Options for Host Configuration In IPv6, there are two main protocol mechanisms for propagating configuration information to hosts: Router Advertisements and DHCP. Historically, RA options have been restricted to those deemed essential for basic network functioning and for which all nodes are configured with exactly the same information. Examples include the Prefix Information Options, the MTU option, etc. On the other hand, DHCP has generally been preferred for configuration of more general parameters and for parameters that may be client-specific. That said, identifying the exact line on whether a particular option should be configured via DHCP vs. an RA option has not always been easy. Generally speaking, however, there has been a desire to define only one mechanism for configuring a given option, rather than defining multiple (different) ways of configuring the same information. One issue with having multiple ways of configuring the same information is that if a host chooses one mechanism, but the network operator chooses a different mechanism, interoperability suffers. For "closed" environments, where the network operator has significant influence over what devices connect to the network and thus what configuration mechanisms they support, the operator may be able to ensure that a particular mechanism is supported by all connected hosts. In more open environments, however, where arbitrary devices may connect (e.g., a WIFI hotspot), problems can arise. To maximize interoperability in such environments hosts would need to implement multiple configuration mechanisms to ensure interoperability. Originally in IPv6, configuring information about DNS servers was performed exclusively via DHCP. In 2007, an RA option was defined, but was published as Experimental [RFC5006]. In 2010, "IPv6 Router Advertisement Options for DNS Configuration" [RFC6106] was published as a Standards Track Document. Consequently, DNS configuration information can now be learned either through DHCP or through RAs. Hosts will need to decide which mechanism (or whether both) should be implemented. Jankiewicz, et al. Expires November 24, 2011 [Page 14] Internet-Draft IPv6 Node Requirements May 2011 7. DNS and DHCP 7.1. DNS DNS is described in [RFC1034], [RFC1035], [RFC3363], and [RFC3596]. Not all nodes will need to resolve names; those that will never need to resolve DNS names do not need to implement resolver functionality. However, the ability to resolve names is a basic infrastructure capability that applications rely on and most nodes will need to provide support. All nodes SHOULD implement stub-resolver [RFC1034] functionality, as in RFC 1034, Section 5.3.1, with support for: - AAAA type Resource Records [RFC3596]; - reverse addressing in ip6.arpa using PTR records [RFC3596]; - EDNS0 [RFC2671] to allow for DNS packet sizes larger than 512 octets. Those nodes are RECOMMENDED to support DNS security extensions [RFC4033], [RFC4034], and [RFC4035]. Those nodes are NOT RECOMMENDED to support the experimental A6 Resource Records [RFC3363]. 7.2. Dynamic Host Configuration Protocol for IPv6 (DHCPv6) - RFC 3315 7.2.1. Other Configuration Information IPv6 nodes use DHCP [RFC3315] to obtain address configuration information (See Section 5.8.5) and to obtain additional (non- address) configuration. If a host implementation supports applications or other protocols that require configuration that is only available via DHCP, hosts SHOULD implement DHCP. For specialized devices on which no such configuration need is present, DHCP may not be necessary. An IPv6 node can use the subset of DHCP (described in [RFC3736]) to obtain other configuration information. 7.2.2. Use of Router Advertisements in Managed Environments Nodes using the Dynamic Host Configuration Protocol for IPv6 (DHCPv6) are expected to determine their default router information and on- link prefix information from received Router Advertisements. 7.3. IPv6 Router Advertisement Options for DNS Configuration - RFC 6106 Router Advertisements have historically limited options to those that are critical to basic IPv6 functioning. Originally, DNS Jankiewicz, et al. Expires November 24, 2011 [Page 15] Internet-Draft IPv6 Node Requirements May 2011 configuration was not included as an RA option and DHCP was the recommended way to obtain DNS configuration information. Over time, the thinking surrounding such an option has evolved. It is now generally recognized that few nodes can function adequately without having access to a working DNS resolver. RFC 5006 was published as an experimental document in 2007, and recently, a revised version was placed on the Standards Track [RFC6106]. Implementations SHOULD implement the DNS RA option [RFC6106]. 8. IPv4 Support and Transition IPv6 nodes MAY support IPv4. 8.1. Transition Mechanisms 8.1.1. Basic Transition Mechanisms for IPv6 Hosts and Routers - RFC 4213 If an IPv6 node implements dual stack and tunneling, then [RFC4213] MUST be supported. 9. Application Support 9.1. Textual Representation of IPv6 Addresses - RFC 5952 Software that allows users and operators to input IPv6 addresses in text form SHOULD support "A Recommendation for IPv6 Address Text Representation" [RFC5952]. 9.2. Application Program Interfaces (APIs) There are a number of IPv6-related APIs. This document does not mandate the use of any, because the choice of API does not directly relate to on-the-wire behavior of protocols. Implementers, however, would be advised to consider providing a common API, or reviewing existing APIs for the type of functionality they provide to applications. "Basic Socket Interface Extensions for IPv6" [RFC3493] provides IPv6 functionality used by typical applications. Implementers should note that RFC3493 has been picked up and further standardized by POSIX [POSIX]. "Advanced Sockets Application Program Interface (API) for IPv6" [RFC3542] provides access to advanced IPv6 features needed by Jankiewicz, et al. Expires November 24, 2011 [Page 16] Internet-Draft IPv6 Node Requirements May 2011 diagnostic and other more specialized applications. "IPv6 Socket API for Source Address Selection" [RFC5014] provides facilities that allow an application to override the default Source Address Selection rules of [RFC3484]. "Socket Interface Extensions for Multicast Source Filters" [RFC3678] provides support for expressing source filters on multicast group memberships. "Extension to Sockets API for Mobile IPv6" [RFC4584] provides application support for accessing and enabling Mobile IPv6 features. [RFC3775] 10. Mobility Mobile IPv6 [RFC3775] and associated specifications [RFC3776] [RFC4877] allow a node to change its point of attachment within the Internet, while maintaining (and using) a permanent address. All communication using the permanent address continues to proceed as expected even as the node moves around. The definition of Mobile IP includes requirements for the following types of nodes: - mobile nodes - correspondent nodes with support for route optimization - home agents - all IPv6 routers At the present time, Mobile IP has seen only limited implementation and no significant deployment, partly because it originally assumed an IPv6-only environment, rather than a mixed IPv4/IPv6 Internet. Recently, additional work has been done to support mobility in mixed- mode IPv4 and IPv6 networks[RFC5555]. More usage and deployment experience is needed with mobility before any specific approach can be recommended for broad implementation in all hosts and routers. Consequently, [RFC3775], [RFC5555], and associated standards such as [RFC4877] are considered a MAY at this time. 11. Security This section describes the specification for security for IPv6 nodes. Achieving security in practice is a complex undertaking. Operational procedures, protocols, key distribution mechanisms, certificate Jankiewicz, et al. Expires November 24, 2011 [Page 17] Internet-Draft IPv6 Node Requirements May 2011 management approaches, etc. are all components that impact the level of security actually achieved in practice. More importantly, deficiencies or a poor fit in any one individual component can significantly reduce the overall effectiveness of a particular security approach. IPsec provides channel security at the Internet layer, making it possible to provide secure communication for all (or a subset of) communication flows at the IP layer between pairs of internet nodes. IPsec provides sufficient flexibility and granularity that individual TCP connections can (selectively) be protected, etc. Although IPsec can be used with manual keying in some cases, such usage has limited applicability and is not recommended. A range of security technologies and approaches proliferate today (e.g., IPsec, TLS, SSH, etc.) No one approach has emerged as an ideal technology for all needs and environments. Moreover, IPsec is not viewed as the ideal security technology in all cases and is unlikely to displace the others. Previously, IPv6 mandated implementation of IPsec and recommended the key management approach of IKE. This document updates that recommendation by making support of the IP Security Architecture [RFC 4301] a SHOULD for all IPv6 nodes. Note that the IPsec Architecture requires (e.g., Sec. 4.5 of RFC 4301) the implementation of both manual and automatic key management. Currently the default automated key management protocol to implement is IKEv2 [RFC5996]. This document recognizes that there exists a range of device types and environments where other approaches to security than IPsec can be justified. For example, special-purpose devices may support only a very limited number or type of applications and an application- specific security approach may be sufficient for limited management or configuration capabilities. Alternatively, some devices my run on extremely constrained hardware (e.g., sensors) where the full IP Security Architecture is not justified. 11.1. Requirements "Security Architecture for the Internet Protocol" [RFC4301] SHOULD be supported by all IPv6 nodes. Note that the IPsec Architecture requires (e.g., Sec. 4.5 of RFC 4301) the implementation of both manual and automatic key management. Currently the default automated key management protocol to implement is IKEv2. As required in [RFC4301], IPv6 nodes implementing the IPsec Architecture MUST implement ESP [RFC4303] and MAY implement AH [RFC4302]. Jankiewicz, et al. Expires November 24, 2011 [Page 18] Internet-Draft IPv6 Node Requirements May 2011 11.2. Transforms and Algorithms The current set of mandatory-to-implement algorithms for the IP Security Architecture are defined in 'Cryptographic Algorithm Implementation Requirements For ESP and AH' [RFC4835]. IPv6 nodes implementing the IP Security Architecture MUST conform to the requirements in [RFC4835]. Preferred cryptographic algorithms often change more frequently than security protocols. Therefore implementations MUST allow for migration to new algorithms, as RFC4835 is replaced or updated in the future. The current set of mandatory-to-implement algorithms for IKEv2 are defined in 'Cryptographic Algorithms for Use in the Internet Key Exchange Version 2 (IKEv2)' [RFC4307]. IPv6 nodes implementing IKEv2 MUST conform to the requirements in [RFC4307] and/or any future updates or replacements to [RFC4307]. 12. Router-Specific Functionality This section defines general host considerations for IPv6 nodes that act as routers. Currently, this section does not discuss routing- specific requirements. 12.1. General 12.1.1. IPv6 Router Alert Option - RFC 2711 The IPv6 Router Alert Option [RFC2711] is an optional IPv6 Hop-by-Hop Header that is used in conjunction with some protocols (e.g., RSVP [RFC2205] or MLD [RFC2710]). The Router Alert option will need to be implemented whenever protocols that mandate its usage (e.g., MLD) are implemented. See Section 5.9. 12.1.2. Neighbor Discovery for IPv6 - RFC 4861 Sending Router Advertisements and processing Router Solicitation MUST be supported. Section 7 of RFC 3775 includes some mobility-specific extensions to Neighbor Discovery. Routers SHOULD implement Sections 7.3 and 7.5, even if they do not implement Home Agent functionality. 13. Network Management Network Management MAY be supported by IPv6 nodes. However, for IPv6 nodes that are embedded devices, network management may be the only Jankiewicz, et al. Expires November 24, 2011 [Page 19] Internet-Draft IPv6 Node Requirements May 2011 possible way of controlling these nodes. 13.1. Management Information Base Modules (MIBs) The following two MIB modules SHOULD be supported by nodes that support an SNMP agent. 13.1.1. IP Forwarding Table MIB IP Forwarding Table MIB [RFC4292] SHOULD be supported by nodes that support an SNMP agent. 13.1.2. Management Information Base for the Internet Protocol (IP) IP MIB [RFC4293] SHOULD be supported by nodes that support an SNMP agent. 14. Security Considerations This document does not directly affect the security of the Internet, beyond the security considerations associated with the individual protocols. Security is also discussed in Section 10 above. 15. IANA Considerations This document has no requests for IANA. 16. Authors and Acknowledgments 16.1. Authors and Acknowledgments (Current Document) For this version of the IPv6 Node Requirements document, the authors would like to thank Hitoshi Asaeda, Brian Carpenter, Tim Chown, Ralph Droms, Sheila Frankel, Sam Hartman, Bob Hinden, Paul Hoffman, Pekka Savola, Yaron Sheffer and Dave Thaler for their comments. 16.2. Authors and Acknowledgments From RFC 4279 The original version of this document (RFC 4279) was written by the IPv6 Node Requirements design team: Jankiewicz, et al. Expires November 24, 2011 [Page 20] Internet-Draft IPv6 Node Requirements May 2011 Jari Arkko jari.arkko@ericsson.com Marc Blanchet marc.blanchet@viagenie.qc.ca Samita Chakrabarti samita.chakrabarti@eng.sun.com Alain Durand alain.durand@sun.com Gerard Gastaud gerard.gastaud@alcatel.fr Jun-ichiro itojun Hagino itojun@iijlab.net Atsushi Inoue inoue@isl.rdc.toshiba.co.jp Masahiro Ishiyama masahiro@isl.rdc.toshiba.co.jp John Loughney john.loughney@nokia.com Rajiv Raghunarayan raraghun@cisco.com Shoichi Sakane shouichi.sakane@jp.yokogawa.com Dave Thaler dthaler@windows.microsoft.com Juha Wiljakka juha.wiljakka@Nokia.com The authors would like to thank Ran Atkinson, Jim Bound, Brian Carpenter, Ralph Droms, Christian Huitema, Adam Machalek, Thomas Narten, Juha Ollila, and Pekka Savola for their comments. Thanks to Mark Andrews for comments and corrections on DNS text. Thanks to Alfred Hoenes for tracking the updates to various RFCs. 17. Appendix: Changes from One ID version to Another RFC Editor: Please remove this section upon publication. 17.1. Appendix: Changes from -09 to -10 1. With changes in requirements for IPsec and Routing Headers, clarified language regarding processing of unknown options, and removed paragraph lising which extension headers were required to be implemented. 2. Removed "RFC4292-bis" from title. 3. Expanded the text on Jumbograms. Jankiewicz, et al. Expires November 24, 2011 [Page 21] Internet-Draft IPv6 Node Requirements May 2011 4. Changed recommendation of DHCPv6 from MAY to SHOULD. 5. Expanded the text on RFC4191, and changed recommendation from MAY to SHOULD. 17.2. Appendix: Changes from -08 to -09 1. Updated MLD section to include reference to Lightweight MLD [RFC5790] 17.3. Appendix: Changes from -07 to -08 1. Dropped reference to "Transmission of IPv6 over IPv4 Domains without Explicit Tunnels" [RFC2429] in favor of a reference to tunneling via Basic IPv6 Transition Mechanisms (RFC4313). 2. Added reference to "Default Router Preferences and More-Specific Routes" [RFC4191] as a MAY. 3. Added reference to "Optimistic Duplicate Address Detection (DAD) for IPv6" (RFC4429). 4. Added reference to RFC4941 "Reserved IPv6 Interface Identifiers" 5. Added Section on APIs. References are FYI, and none are required. 6. Added text that "IPv6 Host-to-Router Load Sharing" [RFC4311] SHOULD be implemented 7. Added reference to RFC5722 (Overlapping Fragments), made it a MUST to implement. 8. Made "A Recommendation for IPv6 Address Text Representation" [RFC5952] a SHOULD. 17.4. Appendix: Changes from -06 to -07 1. Added recommendation that routers implement Section 7.3 and 7.5 of RFC 3775. 2. "IPv6 Router Advertisement Options for DNS Configuration" (RFC 6106) has been published. 3. Further clarifications to the MLD recommendation. 4. "Extended ICMP to Support Multi- Part Messages" [RFC4884] added as a MAY. 5. Added pointer to subnet clarification document (RFC 5942). 6. Added text that "IPv6 Host-to-Router Load Sharing" [RFC4311] SHOULD be implemented 7. Added reference to RFC5722 (Overlapping Fragments), made it a MUST to implement. 8. Made "A Recommendation for IPv6 Address Text Representation" [RFC5952] a SHOULD. Jankiewicz, et al. Expires November 24, 2011 [Page 22] Internet-Draft IPv6 Node Requirements May 2011 17.5. Appendix: Changes from -05 to -06 1. Completely revised IPsec/IKEv2 section. Text has been discussed by 6man and saag. 2. Added text to introduction clarifying that this document applies to general nodes and that other profiles may be more specific in their requirements 3. Editorial cleanups in Neighbor Discovery section in particular. Text made more crisp. 4. Moved some of the DHCP text around. Moved stateful address discussion to Section 5.8.5. 5. Added additional nuance to the redirect requirements w.r.t. default configuration setting. 17.6. Appendix: Changes from -04 to -05 1. Cleaned up IPsec section, but key questions (MUST vs. SHOULD) still open. 2. Added background section on DHCP vs. RA options. 3. Added SHOULD recommendation for DNS configuration vi RAs (RFC5006bis). 4. Cleaned up DHCP section, as it was referring to the M&O bits. 5. Cleaned up the Security Considerations Section. 17.7. Appendix: Changes from -03 to -04 1. Updated the Introduction to indicate document is an applicability statement 2. Updated the section on Mobility protocols 3. Changed Sub-IP Layer Section to just list relevant RFCs, and added some more RFCs. 4. Added Section on SEND (make it a MAY) 5. Redid Section on Privacy Extensions (RFC4941) to add more nuance to recommendation 6. Redid section on Mobility, and added additional RFCs. 18. Appendix: Changes from RFC 4294 1. There have been many editorial clarifications as well as significant additions and updates. While this section highlights some of the changes, readers should not rely on this section for a comprehensive list of all changes. 2. Updated the Introduction to indicate document is an applicability statement and that this document is aimed at general nodes. Jankiewicz, et al. Expires November 24, 2011 [Page 23] Internet-Draft IPv6 Node Requirements May 2011 3. Significantly updated the section on Mobility protocols, adding references and downgrading previous SHOULDs to MAY. 4. Changed Sub-IP Layer Section to just list relevant RFCs, and added some more RFCs. 5. Added Section on SEND (it is a MAY) 6. Revised Section on Privacy Extensions (RFC4941) to add more nuance to recommendation. 7. Completely revised IPsec/IKEv2 Section, downgrading overall recommendation to a SHOULD. 8. Upgraded recommendation of DHCPv6 to SHOULD. 9. Added background section on DHCP vs RA options, added SHOULD recommendation sfor DNS configuration via RAs (RFC 6106), cleaned up DHCP recommendations 10. Added recommendation that routers implement Section 7.3 and 7.5 of RFC 3775. 11. Added pointer to subnet clarification document (RFC 5942). 12. Added text that "IPv6 Host-to-Router Load Sharing" [RFC4311] SHOULD be implemented 13. Added reference to RFC5722 (Overlapping Fragments), made it a MUST to implement. 14. Made "A Recommendation for IPv6 Address Text Representation" [RFC5952] a SHOULD. 15. Removed mention of "DNAME" from the discussion about RFC-3363. 16. Numerous updates to reflect newer versions of IPv6 documents, including 4443, 4291, 3596, 4213. 17. Removed discussion of "Managed" and "Other" flags in RAs. There is no consensus at present on how to process these flags and discussion of their semantics was removed in the most recent update of Stateless Address Autoconfiguration (RFC 4862). 18. Added many more references to optional IPv6 documents. 19. Made "A Recommendation for IPv6 Address Text Representation" [RFC5952] a SHOULD. 20. Added reference to RFC5722 (Overlapping Fragments), made it a MUST to implement. 21. Updated MLD section to include reference to Lightweight MLD [RFC5790] 22. Added SHOULD recommendation for "Default Router Preferences and More-Specific Routes" [RFC4191]. 19. References 19.1. Normative References [RFC1034] Mockapetris, P., "Domain names - concepts and facilities", STD 13, RFC 1034, November 1987. [RFC1035] Mockapetris, P., "Domain names - implementation and Jankiewicz, et al. Expires November 24, 2011 [Page 24] Internet-Draft IPv6 Node Requirements May 2011 specification", STD 13, RFC 1035, November 1987. [RFC1981] McCann, J., Deering, S., and J. Mogul, "Path MTU Discovery for IP version 6", RFC 1981, August 1996. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification", RFC 2460, December 1998. [RFC2671] Vixie, P., "Extension Mechanisms for DNS (EDNS0)", RFC 2671, August 1999. [RFC2710] Deering, S., Fenner, W., and B. Haberman, "Multicast Listener Discovery (MLD) for IPv6", RFC 2710, October 1999. [RFC2711] Partridge, C. and A. Jackson, "IPv6 Router Alert Option", RFC 2711, October 1999. [RFC3315] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C., and M. Carney, "Dynamic Host Configuration Protocol for IPv6 (DHCPv6)", RFC 3315, July 2003. [RFC3484] Draves, R., "Default Address Selection for Internet Protocol version 6 (IPv6)", RFC 3484, February 2003. [RFC3590] Haberman, B., "Source Address Selection for the Multicast Listener Discovery (MLD) Protocol", RFC 3590, September 2003. [RFC3596] Thomson, S., Huitema, C., Ksinant, V., and M. Souissi, "DNS Extensions to Support IP Version 6", RFC 3596, October 2003. [RFC3736] Droms, R., "Stateless Dynamic Host Configuration Protocol (DHCP) Service for IPv6", RFC 3736, April 2004. [RFC3810] Vida, R. and L. Costa, "Multicast Listener Discovery Version 2 (MLDv2) for IPv6", RFC 3810, June 2004. [RFC4033] Arends, R., Austein, R., Larson, M., Massey, D., and S. Rose, "DNS Security Introduction and Requirements", RFC 4033, March 2005. [RFC4034] Arends, R., Austein, R., Larson, M., Massey, D., and S. Rose, "Resource Records for the DNS Security Extensions", Jankiewicz, et al. Expires November 24, 2011 [Page 25] Internet-Draft IPv6 Node Requirements May 2011 RFC 4034, March 2005. [RFC4035] Arends, R., Austein, R., Larson, M., Massey, D., and S. Rose, "Protocol Modifications for the DNS Security Extensions", RFC 4035, March 2005. [RFC4213] Nordmark, E. and R. Gilligan, "Basic Transition Mechanisms for IPv6 Hosts and Routers", RFC 4213, October 2005. [RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 4291, February 2006. [RFC4292] Haberman, B., "IP Forwarding Table MIB", RFC 4292, April 2006. [RFC4293] Routhier, S., "Management Information Base for the Internet Protocol (IP)", RFC 4293, April 2006. [RFC4301] Kent, S. and K. Seo, "Security Architecture for the Internet Protocol", RFC 4301, December 2005. [RFC4303] Kent, S., "IP Encapsulating Security Payload (ESP)", RFC 4303, December 2005. [RFC4307] Schiller, J., "Cryptographic Algorithms for Use in the Internet Key Exchange Version 2 (IKEv2)", RFC 4307, December 2005. [RFC4311] Hinden, R. and D. Thaler, "IPv6 Host-to-Router Load Sharing", RFC 4311, November 2005. [RFC4443] Conta, A., Deering, S., and M. Gupta, "Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification", RFC 4443, March 2006. [RFC4604] Holbrook, H., Cain, B., and B. Haberman, "Using Internet Group Management Protocol Version 3 (IGMPv3) and Multicast Listener Discovery Protocol Version 2 (MLDv2) for Source- Specific Multicast", RFC 4604, August 2006. [RFC4607] Holbrook, H. and B. Cain, "Source-Specific Multicast for IP", RFC 4607, August 2006. [RFC4835] Manral, V., "Cryptographic Algorithm Implementation Requirements for Encapsulating Security Payload (ESP) and Authentication Header (AH)", RFC 4835, April 2007. [RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman, Jankiewicz, et al. Expires November 24, 2011 [Page 26] Internet-Draft IPv6 Node Requirements May 2011 "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861, September 2007. [RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless Address Autoconfiguration", RFC 4862, September 2007. [RFC4941] Narten, T., Draves, R., and S. Krishnan, "Privacy Extensions for Stateless Address Autoconfiguration in IPv6", RFC 4941, September 2007. [RFC5095] Abley, J., Savola, P., and G. Neville-Neil, "Deprecation of Type 0 Routing Headers in IPv6", RFC 5095, December 2007. [RFC5453] Krishnan, S., "Reserved IPv6 Interface Identifiers", RFC 5453, February 2009. [RFC5722] Krishnan, S., "Handling of Overlapping IPv6 Fragments", RFC 5722, December 2009. [RFC5790] Liu, H., Cao, W., and H. Asaeda, "Lightweight Internet Group Management Protocol Version 3 (IGMPv3) and Multicast Listener Discovery Version 2 (MLDv2) Protocols", RFC 5790, February 2010. [RFC5942] Singh, H., Beebee, W., and E. Nordmark, "IPv6 Subnet Model: The Relationship between Links and Subnet Prefixes", RFC 5942, July 2010. [RFC5952] Kawamura, S. and M. Kawashima, "A Recommendation for IPv6 Address Text Representation", RFC 5952, August 2010. [RFC5996] Kaufman, C., Hoffman, P., Nir, Y., and P. Eronen, "Internet Key Exchange Protocol Version 2 (IKEv2)", RFC 5996, September 2010. [RFC6106] Jeong, J., Park, S., Beloeil, L., and S. Madanapalli, "IPv6 Router Advertisement Options for DNS Configuration", RFC 6106, November 2010. [RFC6204] Singh, H., Beebee, W., Donley, C., Stark, B., and O. Troan, "Basic Requirements for IPv6 Customer Edge Routers", RFC 6204, April 2011. 19.2. Informative References [DODv6] DISR IPv6 Standards Technical Working Group, "DoD IPv6 Standard Profiles For IPv6 Capable Products Version 5.0", Jankiewicz, et al. Expires November 24, 2011 [Page 27] Internet-Draft IPv6 Node Requirements May 2011 July 2010, . [POSIX] IEEE, "IEEE Std. 1003.1-2001 Standard for Information Technology -- Portable Operating System Interface (POSIX), ISO/IEC 9945:2002", December 2001, . [RFC0793] Postel, J., "Transmission Control Protocol", STD 7, RFC 793, September 1981. [RFC2205] Braden, B., Zhang, L., Berson, S., Herzog, S., and S. Jamin, "Resource ReSerVation Protocol (RSVP) -- Version 1 Functional Specification", RFC 2205, September 1997. [RFC2429] Bormann, C., Cline, L., Deisher, G., Gardos, T., Maciocco, C., Newell, D., Ott, J., Sullivan, G., Wenger, S., and C. Zhu, "RTP Payload Format for the 1998 Version of ITU-T Rec. H.263 Video (H.263+)", RFC 2429, October 1998. [RFC2464] Crawford, M., "Transmission of IPv6 Packets over Ethernet Networks", RFC 2464, December 1998. [RFC2492] Armitage, G., Schulter, P., and M. Jork, "IPv6 over ATM Networks", RFC 2492, January 1999. [RFC2590] Conta, A., Malis, A., and M. Mueller, "Transmission of IPv6 Packets over Frame Relay Networks Specification", RFC 2590, May 1999. [RFC2675] Borman, D., Deering, S., and R. Hinden, "IPv6 Jumbograms", RFC 2675, August 1999. [RFC3146] Fujisawa, K. and A. Onoe, "Transmission of IPv6 Packets over IEEE 1394 Networks", RFC 3146, October 2001. [RFC3363] Bush, R., Durand, A., Fink, B., Gudmundsson, O., and T. Hain, "Representing Internet Protocol version 6 (IPv6) Addresses in the Domain Name System (DNS)", RFC 3363, August 2002. [RFC3493] Gilligan, R., Thomson, S., Bound, J., McCann, J., and W. Stevens, "Basic Socket Interface Extensions for IPv6", RFC 3493, February 2003. [RFC3542] Stevens, W., Thomas, M., Nordmark, E., and T. Jinmei, "Advanced Sockets Application Program Interface (API) for IPv6", RFC 3542, May 2003. Jankiewicz, et al. Expires November 24, 2011 [Page 28] Internet-Draft IPv6 Node Requirements May 2011 [RFC3678] Thaler, D., Fenner, B., and B. Quinn, "Socket Interface Extensions for Multicast Source Filters", RFC 3678, January 2004. [RFC3775] Johnson, D., Perkins, C., and J. Arkko, "Mobility Support in IPv6", RFC 3775, June 2004. [RFC3776] Arkko, J., Devarapalli, V., and F. Dupont, "Using IPsec to Protect Mobile IPv6 Signaling Between Mobile Nodes and Home Agents", RFC 3776, June 2004. [RFC3971] Arkko, J., Kempf, J., Zill, B., and P. Nikander, "SEcure Neighbor Discovery (SEND)", RFC 3971, March 2005. [RFC3972] Aura, T., "Cryptographically Generated Addresses (CGA)", RFC 3972, March 2005. [RFC4191] Draves, R. and D. Thaler, "Default Router Preferences and More-Specific Routes", RFC 4191, November 2005. [RFC4302] Kent, S., "IP Authentication Header", RFC 4302, December 2005. [RFC4338] DeSanti, C., Carlson, C., and R. Nixon, "Transmission of IPv6, IPv4, and Address Resolution Protocol (ARP) Packets over Fibre Channel", RFC 4338, January 2006. [RFC4380] Huitema, C., "Teredo: Tunneling IPv6 over UDP through Network Address Translations (NATs)", RFC 4380, February 2006. [RFC4429] Moore, N., "Optimistic Duplicate Address Detection (DAD) for IPv6", RFC 4429, April 2006. [RFC4584] Chakrabarti, S. and E. Nordmark, "Extension to Sockets API for Mobile IPv6", RFC 4584, July 2006. [RFC4821] Mathis, M. and J. Heffner, "Packetization Layer Path MTU Discovery", RFC 4821, March 2007. [RFC4877] Devarapalli, V. and F. Dupont, "Mobile IPv6 Operation with IKEv2 and the Revised IPsec Architecture", RFC 4877, April 2007. [RFC4884] Bonica, R., Gan, D., Tappan, D., and C. Pignataro, "Extended ICMP to Support Multi-Part Messages", RFC 4884, April 2007. Jankiewicz, et al. Expires November 24, 2011 [Page 29] Internet-Draft IPv6 Node Requirements May 2011 [RFC4944] Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler, "Transmission of IPv6 Packets over IEEE 802.15.4 Networks", RFC 4944, September 2007. [RFC5006] Jeong, J., Park, S., Beloeil, L., and S. Madanapalli, "IPv6 Router Advertisement Option for DNS Configuration", RFC 5006, September 2007. [RFC5014] Nordmark, E., Chakrabarti, S., and J. Laganier, "IPv6 Socket API for Source Address Selection", RFC 5014, September 2007. [RFC5072] S.Varada, Haskins, D., and E. Allen, "IP Version 6 over PPP", RFC 5072, September 2007. [RFC5121] Patil, B., Xia, F., Sarikaya, B., Choi, JH., and S. Madanapalli, "Transmission of IPv6 via the IPv6 Convergence Sublayer over IEEE 802.16 Networks", RFC 5121, February 2008. [RFC5555] Soliman, H., "Mobile IPv6 Support for Dual Stack Hosts and Routers", RFC 5555, June 2009. [USGv6] National Institute of Standards and Technology, "A Profile for IPv6 in the U.S. Government - Version 1.0", July 2008, . Authors' Addresses Ed Jankiewicz SRI International, Inc. 1161 Broad Street - Suite 212 Shrewsbury, NJ 07702 USA Phone: 443-502-5815 Email: edward.jankiewicz@sri.com Jankiewicz, et al. Expires November 24, 2011 [Page 30] Internet-Draft IPv6 Node Requirements May 2011 John Loughney Nokia 955 Page Mill Road Palo Alto 94303 USA Phone: +1 650 283 8068 Email: john.loughney@nokia.com Thomas Narten IBM Corporation 3039 Cornwallis Ave. PO Box 12195 Research Triangle Park, NC 27709-2195 USA Phone: +1 919 254 7798 Email: narten@us.ibm.com Jankiewicz, et al. Expires November 24, 2011 [Page 31]