TOC |
|
This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as “work in progress.”
The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html.
This Internet-Draft will expire on September 3, 2009.
Copyright (c) 2009 IETF Trust and the persons identified as the document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents in effect on the date of publication of this document (http://trustee.ietf.org/license-info). Please review these documents carefully, as they describe your rights and restrictions with respect to this document.
This document contains information on how to best write an RTP payload format. Reading tips, design practices, and practical tips on how to quickly and with good results produce an RTP payload format specification. A template is also included with instructions that can be used when writing an RTP payload format.
1.
Introduction
1.1.
Structure
2.
Terminology
2.1.
Definitions
2.2.
Acronyms
3.
Preparations
3.1.
Recommend Reading
3.1.1.
IETF Process and Publication
3.1.2.
RTP
3.2.
Important RTP details
3.2.1.
The RTP Session
3.2.2.
RTP Header
3.2.3.
RTP Multiplexing
3.2.4.
RTP Synchronization
3.3.
Signalling Aspects
3.3.1.
Media Types
3.3.2.
Mapping to SDP
3.4.
Transport Characteristics
3.4.1.
Path MTU
4.
Specification Process
4.1.
IETF
4.1.1.
Steps from Idea to Publication
4.1.2.
WG meetings
4.1.3.
Draft Naming
4.1.4.
How to speed up the process
4.2.
Other Standards bodies
4.3.
Propreitary and Vendor Specific
5.
Designing Payload Formats
5.1.
Features of RTP payload formats
5.1.1.
Aggregation
5.1.2.
Fragmentation
5.1.3.
Interleaving and Transmission Re-Scheduling
5.1.4.
Media Back Channels
5.1.5.
Scalability
5.1.6.
High Packet Rates
6.
Current Trends in Payload Format Design
6.1.
Audio Payloads
6.2.
Video
6.3.
Text
7.
Important Specification Sections
7.1.
Security Consideration
7.2.
Congestion Control
7.3.
IANA Consideration
8.
Authoring Tools
8.1.
Editing Tools
8.2.
Verification Tools
9.
Open Issues
10.
IANA Considerations
11.
Security Considerations
12.
RFC Editor Consideration
13.
Acknowledgements
14.
Informative References
Appendix A.
RTP Payload Format Template
A.1.
Title
A.2.
Front page boilerplate
A.3.
Abstract
A.4.
Table of Content
A.5.
Introduction
A.6.
Conventions, Definitions and Acronyms
A.7.
Media Format Background
A.8.
Payload format
A.8.1.
RTP Header Usage
A.8.2.
Payload Header
A.8.3.
Payload Data
A.9.
Payload Examples
A.10.
Congestion Control Considerations
A.11.
Payload Format Parameters
A.11.1.
Media Type Definition
A.11.2.
Mapping to SDP
A.12.
IANA Considerations
A.13.
Securtiy Considerations
A.14.
References
A.14.1.
Normative References
A.14.2.
Informative References
A.15.
Author Addresses
§
Author's Address
TOC |
RTP (Schulzrinne, H., Casner, S., Frederick, R., and V. Jacobson, “RTP: A Transport Protocol for Real-Time Applications,” July 2003.) [RFC3550] payload formats define how a specific real-time data format is structured in the payload of an RTP packet. A real-time data format without a payload format specification can't be transported using RTP. This creates an interest from many individuals/organizations with media encoders or other types of real-time data to define RTP payload formats. The specification of a well designed RTP payload format is non-trivial and requires knowledge of both RTP and the real-time data format.
This document intends to help any author of an RTP payload format to make important design decisions, consider important features of RTP, security, etc. The document is also intended to be a good starting point for any person with little experience in IETF and/or RTP to learn the necessary steps.
This document extends and updates the information that are available in "Guidelines for Writers of RTP Payload Format Specifications" (Handley, M. and C. Perkins, “Guidelines for Writers of RTP Payload Format Specifications,” December 1999.) [RFC2736]. Since this RFC was written further experience has been gained on the design and specification of RTP payload format. Several new RTP profiles, and robustness tools has also been defined, which needs to be considered.
We also discuss the possible venues of defining an RTP payload format, in IETF, by other standard bodies and proprietary ones. Independent on the intended venue of specification, all will gain from this document.
TOC |
This document has several different parts discussing different aspects of the creation of an RTP payload format specification. After the introduction and definitions there are a section discussing the preparations the author(s) should do before start writing. The following section discusses the different processes used when specifying and completing an payload format, with focus on working inside the IETF. Section 5 discusses the design of payload formats themselves in detail. Section 6 discusses the current design trends and provides good examples of practices that should be followed when applicable. Following that there is a discussion on important sections in the RTP payload format specification itself, like security and IANA considerations. This document ends with an appendix containing an template that can be used when writing RTP payload formats.
TOC |
TOC |
- Media Stream:
- A sequence of RTP packets that together provides all or parts of a media. It is scoped in RTP by the RTP session and a single sender source.
- RTP Session:
- An association among a set of participants communicating with RTP. The distinguishing feature of an RTP session is that each maintains a full, separate space of SSRC identifiers. See also Section (The RTP Session).
- RTP Payload Format:
- The RTP Payload format specifies how a specific media format is put into the RTP Payloads. Thus enabling the format to be used in RTP sessions.
TOC |
- ABNF:
- Augmented Backus-Naur Form
- ADU:
- Application Data Unit
- ALF:
- Application Level Framing
- ASM:
- Any-Source Multicast
- AVT:
- Audio Video Transport
- BCP:
- Best Current Practice
- ID:
- Internet Draft
- MTU:
- Maximum Transmission Unit
- WG:
- Working Group
- QoS:
- Quality of Service
- RFC:
- Request For Comment
- RTP:
- Real-time Transport Protocol
- RTCP:
- RTP Control Protocol
- RTT:
- Round Trip Time
- SSM:
- Source Specific Multicast
TOC |
RTP is a complex real-time media delivery framework and it has a lot of details to consider when writing an RTP payload format. There is also important to have a good understanding of the media codec/format so that all its important features and properties are considered. First when one has sufficient understanding of both parts can one produce an RTP payload format of high quality. On top of this, one needs to understand the process within IETF and especially the AVT WG to quickly go from initial idea to a finished RFC. This and the next section helps an author prepare himself in those regards.
TOC |
In the below sub sections there are a number of documents listed. Not all needs to be read in full detail. However, an author basically needs to be aware of everything listed below.
TOC |
For newcomers to IETF it is strongly recommended that one reads the "Tao of the IETF" (Hoffman, P. and S. Harris, “The Tao of IETF - A Novice's Guide to the Internet Engineering Task Force,” September 2006.) [RFC4677] that goes through most things that one needs to know about the IETF. It contains information about history, organisational structure, how the WG and meetings work and many more details.
The main part of the IETF process is defined in RFC 2026 (Bradner, S., “The Internet Standards Process -- Revision 3,” October 1996.) [RFC2026]. In addition an author needs to understands the IETF rules and rights associated with copyright and IPR documented in BCP 78 (Bradner, S. and J. Contreras, “Rights Contributors Provide to the IETF Trust,” November 2008.) [RFC5378] and BCP 79 (Bradner, S., “Intellectual Property Rights in IETF Technology,” March 2005.) [RFC3979]. RFC 2418 (Bradner, S., “IETF Working Group Guidelines and Procedures,” September 1998.) [RFC2418] describes the WG process, the relation between the IESG and the WG, and the responsibilities of WG chairs and participants.
It is important to note that the RFC series contains documents of several different classifications; standards track, informational, experimental, best current practice (BCP), and historic. The standard tracks contains documents of three different maturity classifications, proposed, draft and Internet Standard. A standards track document must start as proposed, after proved interoperability of all the features it can be moved to draft standard, and final when further experience has been gathered it can be moved to Internet standard. As the content of the RFCs are not allowed to be changed, the only way of updating an RFC is to write and publish a new one that either updates or replaces the old one. Therefore it is important to both consider the Category field in the header and check if the RFC one is reading or going to reference is the latest and valid. One way of checking the current status of an RFC is to use the RFC-editor's RFC search engine, which displays the current status and which if any RFCs that updates or obsolete it.
Before starting to write an draft one should also read the Internet Draft writing guidelines (http://www.ietf.org/ietf/1id-guidelines.txt), the ID checklist (http://www.ietf.org/ID-Checklist.html) and the RFC editorial guidelines and procedures (http://www.rfc-editor.org/policy.html, “RFC Editorial Guidelines and Procedures,” July 2008.) [RFC‑ED]. Another document that can be useful is the "Guide for Internet Standards Writers" (Scott, G., “Guide for Internet Standards Writers,” June 1998.) [RFC2360].
There are also a number of documents to consider in process of writing of drafts intended to become RFCs. These are important when writing certain type of text.
- RFC 2606:
- When writing examples using DNS names in Internet drafts, those name shall be using the example.com, example.net, and example.org domains.
- RFC 3849:
- Defines the range of IPv6 unicast addresses (2001:DB8::/32) that should be used in any examples.
- RFC 3330:
- Defines the range of IPv4 unicast addresses reserved for documentation and examples: 192.0.2.0/24.
- RFC 5234:
- Augmented Backus-Naur Form (ABNF) is often used when writing text field specifications. Not that commonly used in RTP payload formats but may be useful when defining Media Type parameters of some complexity.
TOC |
The recommended reading for RTP consist of several different parts; design guidelines, the RTP protocol, profiles, robustness tools, and media specific recommendations.
Any author of RTP payload formats should start with reading RFC 2736 (Handley, M. and C. Perkins, “Guidelines for Writers of RTP Payload Format Specifications,” December 1999.) [RFC2736] which contains an introduction to the application layer framing (ALF) principle, the channel characteristics of IP channels, and design guidelines for RTP payload formats. The goal of ALF is to be able to transmit Application Data Units (ADUs) that are independently usable by the receiver in individual RTP packets. Thus minimizing dependencies between RTP packets and the effects of packet loss.
Then it is suitable to learn more about the RTP protocol, by studying the RTP specification RFC 3550 (Schulzrinne, H., Casner, S., Frederick, R., and V. Jacobson, “RTP: A Transport Protocol for Real-Time Applications,” July 2003.) [RFC3550] and the existing profiles. As a complement to the standards document there exist a book totally dedicated to RTP (Colin , “RTP: Audio and Video for the Internet,” June 2003.) [CSP‑RTP]. There exist several profiles for RTP today, but all are based on the "RTP Profile for Audio and Video Conferences with Minimal Control" (RFC 3551) (Schulzrinne, H. and S. Casner, “RTP Profile for Audio and Video Conferences with Minimal Control,” July 2003.) [RFC3551] (abbreviated AVP). The other profiles that one should known about are Secure RTP (SAVP) (Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K. Norrman, “The Secure Real-time Transport Protocol (SRTP),” March 2004.) [RFC3711], "Extended RTP Profile for RTCP-based Feedback" (Ott, J., Wenger, S., Sato, N., Burmeister, C., and J. Rey, “Extended RTP Profile for Real-time Transport Control Protocol (RTCP)-Based Feedback (RTP/AVPF),” July 2006.) [RFC4585] and "Extended Secure RTP Profile for RTCP-based Feedback (RTP/SAVPF)" (Ott, J. and E. Carrara, “Extended Secure RTP Profile for Real-time Transport Control Protocol (RTCP)-Based Feedback (RTP/SAVPF),” February 2008.) [RFC5124]. It is important to understand RTP and the AVP profile in detail. For the other profiles it is sufficient to have an understanding on what functionality they provided and the limitations they create.
There has been developed a number of robustness tools for RTP. The tools are for different use cases and real-time requirements.
- RFC 2198:
- The "RTP Payload for Redundant Audio Data" (Perkins, C., Kouvelas, I., Hodson, O., Hardman, V., Handley, M., Bolot, J., Vega-Garcia, A., and S. Fosse-Parisis, “RTP Payload for Redundant Audio Data,” September 1997.) [RFC2198] provides functionalities to provided redundant copies of audio or text payloads. These redundant copies are sent together with an primary format in the same RTP payload. This format relies on the RTP timestamp to determine where data belongs in a sequence and therefore is usually primarily suitable to be used with audio. However also the RTP Payload format for T.140 (Hellstrom, G. and P. Jones, “RTP Payload for Text Conversation,” June 2005.) [RFC4103] text format uses this format. The formats major property is that it only preserves the timestamp of the redundant payloads, not the original sequence number. Thus making it unusable for most video formats. This format is also only suitable for media formats that produce relatively small RTP payloads.
- RFC 5109:
- The "RTP Payload Format for Generic Forward Error Correction" [RFC5109] (Li, A., “RTP Payload Format for Generic Forward Error Correction,” December 2007.) provides an XOR based FEC of the whole or parts of a the packets for a number of RTP packets. These FEC packets are sent in a separate stream or as a redundant encoding using RFC 2198. This FEC scheme has certain restrictions in the number of packets it can protect. It is suitable for low to medium delay tolerant applications with limited amount of RTP packets.
- RTP Retransmission:
- The RTP retransmission scheme (Rey, J., Leon, D., Miyazaki, A., Varsa, V., and R. Hakenberg, “RTP Retransmission Payload Format,” July 2006.) [RFC4588] is used for semi-reliability of the most important RTP packets in a media stream. The scheme is not intended, nor suitable, to provide full reliability. It requires the application to be quite delay tolerant as a minimum of one round-trip time plus processing delay is required to perform an retransmission. Thus it is mostly suitable for streaming applications but may also be usable in certain other cases when operating on networks with short round trip times (RTT).
- RTP over TCP:
- RFC 4571 [RFC4571] (Lazzaro, J., “Framing Real-time Transport Protocol (RTP) and RTP Control Protocol (RTCP) Packets over Connection-Oriented Transport,” July 2006.) defines how one sends RTP and RTCP packet over connection oriented transports like TCP. If one uses TCP one gets reliability for all packets but loose some of the real-time behavior that RTP was designed to provide. Issues with TCP transport of real-time media include head of line blocking and wasting resources on retransmission of already late data. TCP is also limited to point-to-point connections which further restricts its applicability.
There has also been discussion and also design of RTP payload formats, e.g AMR and AMR-WB[RFC4867] (Sjoberg, J., Westerlund, M., Lakaniemi, A., and Q. Xie, “RTP Payload Format and File Storage Format for the Adaptive Multi-Rate (AMR) and Adaptive Multi-Rate Wideband (AMR-WB) Audio Codecs,” April 2007.), supporting the unequal error detection provided by UDP-Lite [RFC3828] (Larzon, L-A., Degermark, M., Pink, S., Jonsson, L-E., and G. Fairhurst, “The Lightweight User Datagram Protocol (UDP-Lite),” July 2004.). The idea is that by not having a checksum over part of the RTP payload one can allow bit-errors from the lower layers. By allowing bit-errors one can increase the efficiency of some link layers, and also avoid unnecessary discards of data when the payload and media codec could get at least some utility from the data. The main issue is that one has no idea on the level of bit-errors present in the unprotected part of the payload. Which makes it hard or impossible to determine if one can design something usable or not. Payload format designers are recommended against considering features for unequal error detection unless very clear requirements exist.
There also exist some management and monitoring extensions.
- RFC 2959:
- The RTP protocol Management Information Database (MIB) (Baugher, M., Strahm, B., and I. Suconick, “Real-Time Transport Protocol Management Information Base,” October 2000.) [RFC2959] that is used with SNMP [RFC3410] (Case, J., Mundy, R., Partain, D., and B. Stewart, “Introduction and Applicability Statements for Internet-Standard Management Framework,” December 2002.) to configure and retrieve information about RTP sessions.
- RFC 3611:
- The RTCP Extended Reports (RTCP XR) (Friedman, T., Caceres, R., and A. Clark, “RTP Control Protocol Extended Reports (RTCP XR),” November 2003.) [RFC3611] consist of a framework for reports sent within RTCP. It can easily be extended by defining new report formats in future. The report formats that are defined are providing report information on; packet loss vectors, packet duplication, packet reception times, RTCP statistics summary and VoIP Quality. It also defines a mechanism that allows receivers to calculate the RTT to other session participants when used.
- RMONMIB:
- The remote monitoring work group has defined a mechanism (Waldbusser, S., Cole, R., Kalbfleisch, C., and D. Romascanu, “Introduction to the Remote Monitoring (RMON) Family of MIB Modules,” August 2003.) [RFC3577] based on usage of the MIB that can be an alternative to RTCP XR.
There has also been developed a number of transport optimizations that are used in certain environments. They are all intended to be transparent and not need special consideration by the RTP payload format writer. Thus they are primarily listed here for informational reasons and do not require deeper studies.
- RFC 2508:
- Compressing IP/UDP/RTP headers for slow serial links (CRTP) (Casner, S. and V. Jacobson, “Compressing IP/UDP/RTP Headers for Low-Speed Serial Links,” February 1999.) [RFC2508] is the first IETF developed RTP header compression mechanism. It provides quite good compression however it has clear performance problems when subject to packet loss or reordering between compressor and decompressor.
- RFC 3095:
- Is the base specification of the robust header compression (ROHC) protocol (Bormann, C., Burmeister, C., Degermark, M., Fukushima, H., Hannu, H., Jonsson, L-E., Hakenberg, R., Koren, T., Le, K., Liu, Z., Martensson, A., Miyazaki, A., Svanbro, K., Wiebke, T., Yoshimura, T., and H. Zheng, “RObust Header Compression (ROHC): Framework and four profiles: RTP, UDP, ESP, and uncompressed,” July 2001.) [RFC3095]. This solution was created as a result of CRTP's lack of performance when subject to losses.
- RFC 3545:
- Enhanced compressed RTP (E-CRTP) (Koren, T., Casner, S., Geevarghese, J., Thompson, B., and P. Ruddy, “Enhanced Compressed RTP (CRTP) for Links with High Delay, Packet Loss and Reordering,” July 2003.) [RFC3545] was developed to provide extensions to CRTP that allows for better performance over links with long RTTs, packet loss and/or reordering.
- RFC 4170:
- Tunneling Multiplexed Compressed RTP (TCRTP) (Thompson, B., Koren, T., and D. Wing, “Tunneling Multiplexed Compressed RTP (TCRTP),” November 2005.) [RFC4170] is a solution that allows header compression within a tunnel carrying multiple multiplexed RTP flows. This is primarily used in voice trunking.
There exist a couple of different security mechanisms that may be used with RTP. All generic mechanisms need to be transparent for the RTP payload format and nothing that needs special consideration. The main reason that there exist different solutions is that different applications have different requirements thus different solutions have been developed. The main properties for a RTP security mechanism are to provide confidentiality for the RTP payload, integrity protection to detect manipulation of payload and headers, and source authentication. Not all mechanism provides all of these features which will need to be considered when used.
- RTP Encryption:
- Section 9 of RFC 3550 describes a mechanism to provide confidentiality of the RTP and RTCP packets, using per default DES encryption. It may use other encryption algorithms if both end-points agree on it. This mechanism is not recommend due to its weak security properties of the used encryption algorithms. It also lacks integrity and source authentication mechanisms.
- SRTP:
- The profile for Secure RTP (SAVP) (Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K. Norrman, “The Secure Real-time Transport Protocol (SRTP),” March 2004.) [RFC3711] and the derived profile (SAVPF (Ott, J. and E. Carrara, “Extended Secure RTP Profile for Real-time Transport Control Protocol (RTCP)-Based Feedback (RTP/SAVPF),” February 2008.) [RFC5124]) is a solution that provides confidentiality, integrity protection and partial source authentication.
- IPsec:
- IPsec (Kent, S. and K. Seo, “Security Architecture for the Internet Protocol,” December 2005.) [RFC4301] may also be used to protect RTP and RTCP packet.
- TLS:
- TLS (Dierks, T. and E. Rescorla, “The Transport Layer Security (TLS) Protocol Version 1.2,” August 2008.) [RFC5246] may also be used to provide transport security between two end-point of the TLS connection for a flow of RTP packets that are framed over TCP.
- DTLS:
- Datagram TLS (Rescorla, E. and N. Modadugu, “Datagram Transport Layer Security,” April 2006.) [RFC4347] is an alternative to TLS that allow TLS to be used over datagrams, like UDP. Thus it has the potential for being used to protect RTP over UDP. However the necessary signalling mechanism for using it that has not yet been developed in any of the IETF real-time media application signalling protocols.
TOC |
This section does not remove the necessity of reading up on RTP. However it does point out a couple of important details to remember when designing the payload format.
TOC |
The definition of the RTP session from RFC 3550 is:
"An association among a set of participants communicating with RTP. A participant may be involved in multiple RTP sessions at the same time. In a multimedia session, each medium is typically carried in a separate RTP session with its own RTCP packets unless the encoding itself multiplexes multiple media into a single data stream. A participant distinguishes multiple RTP sessions by reception of different sessions using different pairs of destination transport addresses, where a pair of transport addresses comprises one network address plus a pair of ports for RTP and RTCP. All participants in an RTP session may share a common destination transport address pair, as in the case of IP multicast, or the pairs may be different for each participant, as in the case of individual unicast network addresses and port pairs. In the unicast case, a participant may receive from all other participants in the session using the same pair of ports, or may use a distinct pair of ports for each.
The distinguishing feature of an RTP session is that each maintains a full, separate space of SSRC identifiers (defined next). The set of participants included in one RTP session consists of those that can receive an SSRC identifier transmitted by any one of the participants either in RTP as the SSRC or a CSRC (also defined below) or in RTCP. For example, consider a three-party conference implemented using unicast UDP with each participant receiving from the other two on separate port pairs. If each participant sends RTCP feedback about data received from one other participant only back to that participant, then the conference is composed of three separate point-to-point RTP sessions. If each participant provides RTCP feedback about its reception of one other participant to both of the other participants, then the conference is composed of one multi-party RTP session. The latter case simulates the behavior that would occur with IP multicast communication among the three participants.
The RTP framework allows the variations defined here, but a particular control protocol or application design will usually impose constraints on these variations."
TOC |
The RTP header contains two fields that require additional specification by the RTP payload format, namely the RTP Timestamp and the marker bit. Certain RTP payload formats also uses the RTP sequence number to realize certain functionalities. The payload type is used to indicate the used payload format.
- Marker bit:
- A single bit normally used to provide important indications. In audio it is normally used to indicate the start of an talk burst. This to enable jitter buffer adaptation prior to this with minimal audio quality impact. In video the marker bit is normally used to indicate the last packet part of an frame. This enables an decoder to finish decoding the picture, where it otherwise may need to wait for the next packet to explicitly know that.
- Timestamp:
- The RTP timestamp indicate the time instance the media belongs to. For discrete media, like video it normally indicates when the media (frame) was sampled. For continuous media it normally indicates the first time instance the media present in the payload represents. For audio this is the sampling time of the first sample. All RTP payload formats must specify the meaning of the timestamp value and which clock rates that are allowed. Note that clock rates below 1000 Hz is not appropriate due to RTCP measurements function that in that case lose resolution. Also RTP payload formats that has a timestamp definition which results in that no or little correlation between the media time instance and its transmission time result in that the RTCP jitter calculation becomes unusable due to the sender side introduced errors. It should be noted if the payload format has this property or not.
- Sequence number:
- The sequence number are monotonically increasing and set as packets are sent. That property is used in many payload formats to recover the order of everything from the whole stream down to fragments of ADUs and the order they shall be decoded.
- Payload Type:
- Commonly the same payload type is used for a media stream for the whole duration of a session. However in some cases it may be required to change the payload format or its configuration during the session. The payload type is used to indicate on a per packet basis which format is used. Thus certain major configuration information can be bound to a payload type value by out-of-band signalling. Examples of this would be video decoder configuration information.
- SSRC:
- The Sender Source ID is normally not used by a payload format other than identifying the RTP timestamp and sequence number space a packet belongs to, allowing the simultaneously reception of multiple senders. However there are certain of the mechanisms the make RTP robuster that are RTP payloads that have used multiple SSRCs and bound them together to correctly separate original data and repair or redundant data.
The remaining fields are commonly not influencing the RTP payload format. The padding bit is worth clarifying as it indicates that one or more bytes are appended after the RTP payload. This padding must be removed by a receiver before payload format processing can occur. Thus it is completely separate from any padding that may occur within the payload format itself.
TOC |
RTP has three multiplexing points that are used for different purposes. A proper understanding of this is important to correctly utilized them.
The first one is separation of media streams of different types, which is accomplished using different RTP sessions. So for example in the common multi-media session with audio and video, RTP multiplex audio and video on different RTP sessions. To achieve this separation, transport level functionalities are use, normally UDP port numbers. Different RTP sessions are also used to realize layered scalability as it allows a receiver to select one or more layers for multicasted RTP sessions simply by joining the multicast groups the desired layers are transported over. This also allows different Quality of Service (QoS) be applied to different media.
The next point is separation of different sources within a RTP session. Here RTP uses the SSRC (Sender Source) which identifies individual sources. An example of individual sources in audio RTP session, would be different microphones, independent of if they are from the same host or different hosts. For each SSRC a unique RTP sequence number and timestamp space is used.
The third multiplexing point is the RTP headers payload type field. The payload type identifies what format the content in the RTP payload has. This includes different payload format configurations, different codecs, and also usage of robustness mechanisms like the one described in RFC 2198 (Perkins, C., Kouvelas, I., Hodson, O., Hardman, V., Handley, M., Bolot, J., Vega-Garcia, A., and S. Fosse-Parisis, “RTP Payload for Redundant Audio Data,” September 1997.) [RFC2198].
TOC |
There are several types of synchronization and we will here describe how RTP handles the different types:
- Intra media:
- The synchronization within a media stream from a source is accomplished using the RTP timestamp field. Each RTP packet carry the RTP timestamp that specifies the media contained in this packets position in relation to other media on the time line. This is especially useful in cases of discontinues transmissions. Discontinues can also be caused by the network and with extensive losses the RTP timestamp tells the receiver how much later than previously received media the media shall be played out.
- Inter media:
- As applications commonly has a desire to use several media types at the same time there exist a need to synchronize also the different medias from the same source. This puts two requirements on RTP; possibility to determine which media is from the same source and if they should be synchronized with each other; and the functionality to facilitate the synchronization itself.
The first part of Inter media synchronization is to determine which SSRCs in each session that should be synchronized with each other. This is accomplished by comparing the RTCP SDES CNAME field. SSRCs with the same CNAME in different RTP session should be synchronized.
The actual RTCP mechanism for inter media synchronization is based on that each media stream provide a position on the media specific time line (measured in RTP timestamp ticks) and a common reference time line. The common reference time line is in RTCP expressed as an wall clock time in the Network Time Protocol (NTP) format. It is important to notice that the wall clock time is not required to be synchronized between hosts, for example by using NTP (Mills, D., “Network Time Protocol (Version 3) Specification, Implementation,” March 1992.) [RFC1305] . It can even have nothing at all to do with the actual time, for example the host system's uptime can be used for this purpose. The important factor is that all media streams from a particular source that are being synchronized uses the same reference clock to derive there relative RTP timestamp time scales.
In the below Figure (RTCP Synchronization) it is depicted how if one receives RTCP Sender Report (SR) packet P1 in one media stream and RTCP SR packet P2 in the other session, then one can calculate the corresponding RTP timestamp values for any arbitrary point in time T. However to be able to do that it is also required to know the RTP timestamp rates for each media currently used in the sessions
TS1 --+---------------+-------> | | P1 | | | NTP ---+-----+---------T------> | | P2 | | | TS2 ---------+---------+---X-->
Figure 1: RTCP Synchronization |
Lets assume that media 1 uses a RTP Timestamp clock rate of 16 kHz, and media 2 a rate of 90 kHz. Then the TS1 and TS2 for point T can be calculated in the following way: TS1(T) = TS1(P1) + 16000 * (NTP(T)-NTP(P1)) and TS2(T) = TS2(P2) + 90000 * (NTP(T)-NTP(P2)). This calculation is useful as it allows to generate a common synchronization point for which all time values are provided (TS1(T), TS2(T) and T). So when one like to calculate at which NTP time the TS present in packet X corresponds to one can do that in the following way: NTP(X) = NTP(T) + (TS2(X) - TS2(T))/90000.
TOC |
RTP payload formats are used in the context of application signalling protocols such as SIP (Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, “SIP: Session Initiation Protocol,” June 2002.) [RFC3261] using SDP (Handley, M., Jacobson, V., and C. Perkins, “SDP: Session Description Protocol,” July 2006.) [RFC4566] with Offer/Answer (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.) [RFC3264], RTSP (Schulzrinne, H., Rao, A., and R. Lanphier, “Real Time Streaming Protocol (RTSP),” April 1998.) [RFC2326] or SAP (Schulzrinne, H., Rao, A., and R. Lanphier, “Real Time Streaming Protocol (RTSP),” April 1998.) [RFC2326]. These examples all uses SDP to indicate which and how many media streams that are desired to be used in the session and their configuration. To be able to declare or negotiate which media format and RTP payload packetization the payload format must be given an identifier. In addition to the identifier many payload formats also have the need to carry further configuration information out-of-band in regards to the RTP payloads prior to the media transport session.
The above examples of session establishing protocols all use SDP, however also other session description formats may be used. For example there have been discussion on a new Session Description format within IETF (SDP-NG). To prevent locking the usage of RTP to SDP based out-of-band signalling, the payload formats are identified using an separate definition format for the identifier and parameters. That format is the Media Type.
TOC |
Media types (Freed, N. and J. Klensin, “Media Type Specifications and Registration Procedures,” December 2005.) [RFC4288] was originally created for identifying media formats included in email. Media types are today also used in HTTP (Fielding, R., Gettys, J., Mogul, J., Frystyk, H., Masinter, L., Leach, P., and T. Berners-Lee, “Hypertext Transfer Protocol -- HTTP/1.1,” June 1999.) [RFC2616], MSRP (Campbell, B., Mahy, R., and C. Jennings, “The Message Session Relay Protocol (MSRP),” September 2007.) [RFC4975] and many other protocols to identify arbitrary content carried within the protocols. Media types also provide a media hierarchy that fits RTP payload formats well. Media type names are two-part and consist of content type and sub-type separated with a slash, e.g. "audio/PCMA" or "video/h263-2000". It is important to choose the correct content-type when creating the media type identifying an RTP payload format. However in most cases there is little doubt what content type the format belongs to. Guidelines for choosing the correct media type and registration rules are present in RFC 4288 (Freed, N. and J. Klensin, “Media Type Specifications and Registration Procedures,” December 2005.) [RFC4288]. The additional rules for media types for RTP payload formats are present in RFC 4855 (Casner, S., “Media Type Registration of RTP Payload Formats,” February 2007.) [RFC4855].
Media types are allowed any number of parameters which are divided into two groups, required and optional parameters. They are always on the form name=value. There exist no restriction on how the value is defined from media types perspective, except that parameters must have value. However the carrying of media types in SDP etc. has resulted in the following restrictions that needs to be followed to make media types for RTP payload format usable:
TOC |
As SDP (Handley, M., Jacobson, V., and C. Perkins, “SDP: Session Description Protocol,” July 2006.) [RFC4566] is so commonly used as an out-of-band signalling channel, a mapping of the media type exist. The details on how to map the media type and its parameters into SDP are described in RFC 4855 (Casner, S., “Media Type Registration of RTP Payload Formats,” February 2007.) [RFC4855]. However this is not sufficient to explain how certain parameter shall be interpreted for example in the context of Offer/Answer negotiation (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.) [RFC3264].
TOC |
The Offer/Answer (O/A) model allows SIP to negotiate media formats and which payload formats and their configuration is used in a session. However O/A does not define a default behavior and instead points out the need to define how parameters behave. To make things even more complex the direction of media within a session do have impact on these rules, thus some cases may require description separately for peers that are send only, receiver only or both senders and receivers as identified by the SDP attributes a=sendonly, a=recvonly, and a=sendrecv. In addition any usage of multicast puts a further limitations as the same media stream is delivered to all participants. If those restrictions are to limiting also to be used in unicast then separate rules for unicast and multicast will be required.
The most common O/A interpretation and the simplest is for declarative parameters, i.e. the sending entity can declare a value and that has no direct impact on the other agents values. This declared value applies to all media that are going to be sent to the declaring entity. For example most video codecs has level parameter which tells the other participants the highest complexity the video decoder supports. The level parameter can be declared independently by two participants in a unicast session as it will be the media sender responsibility to transmit a video stream that fulfills the limitation the other has declared. However in multicast it will be necessary to send a stream that follows the limitation of the weakest receiver, i.e. the one that has supports the lowest level. To simplify the negotiation in these cases it is common to require any answerer to a multicast session to take a yes or no approach to parameters.
"Negotiated" parameters are another type of parameters, for which both sides needs to agree on their values. Such parameter requires that the answerer either accept as they are offered or remove the payload type the parameter belonged to. The removal of the payload type from the answer indicates to the offerer the lack of support. An unfortunate implications of the need to use complete payload types to indicate each configuration possible to achieve interoperability, is that the number of payload types necessary can quickly grow big. This is one reason to keep the total number of set of capabilities that may be implemented limited.
The most problematic type of parameters are those that relates with the transmission the entity performs. They do not really fit the O/A model but can be shoe-horned in. Example of such parameters can be found in the H.264 video code's payload format (Wenger, S., Hannuksela, M., Stockhammer, T., Westerlund, M., and D. Singer, “RTP Payload Format for H.264 Video,” February 2005.) [RFC3984], where the name of all parameters with this property starts sprop-. The issue that exist is that they declare properties for a media stream one don't yet know if the other party accept. The best one can make of the situation is to explain the assumption that the other party will accept the same reception parameter as the offerer of the session. If the answerer needs to change any declarative parameter then the offerer may be required to make an new offer to update the parameter values for its outgoing media stream.
Another issue to consider is the sendonly media streams in offers. For all parameters that relates to what one accepts to receive those don't have any meaning other than provide a template for the answering entity. It is worth pointing out in the specification that these provides recommended set of parameter values by the sender. Note that sendonly streams in answers will need to indicate the offerers parameters to ensure that the offerer can match the answer to the offer.
A further issue with offer/answer which complicates things is that it is allowed to renumber the payload types between offer and answer. This is not recommended but allowed for support of gateways to the ITU conferencing suit. Which means that answers for payload types needs to be possible to bind to the ones in the offer even when the payload type number has been changed, and some of the proposed payload types have been removed. This must normally be done based on configurations offered, thus negotiated parameters becomes vital.
TOC |
SAP (Session Announcement Protocol) (Handley, M., Perkins, C., and E. Whelan, “Session Announcement Protocol,” October 2000.) [RFC2974] is used for announcing multicast sessions. Independently of the usage of Source Specific Multicast (SSM) (Bhattacharyya, S., “An Overview of Source-Specific Multicast (SSM),” July 2003.) [RFC3569] or Any-Source Multicast (ASM), the SDP provided by SAP applies to all participants. All media that is sent to the session must follow the media stream definition as specified by the SDP. Thus enabling everyone to receive the session if they support the configuration. Here SDP provides a one way channel with no possibility to affect the configuration defined by SDP that the session creator has decided upon. Any RTP Payload format that requires parameters for the send direction and which needs individual values per implementation or instance will fail in a SAP session for a multicast session allowing anyone to send.
Real-Time Streaming Protocol (RTSP) (Schulzrinne, H., Rao, A., and R. Lanphier, “Real Time Streaming Protocol (RTSP),” April 1998.) [RFC2326] allows the negotiation of transport parameters for media streams part of a streaming session between a server and client. RTSP has divided the transport parameters from the media configuration. SDP is commonly used for media configuration in RTSP and is sent to the client prior to session establishment, either through the usage of the DESCRIBE method or an out-of-band channel like HTTP, email etc. The SDP is used to determine which media streams and what formats are being used before the session establishment.
Thus both SAP and RTSP uses SDP to configure receivers and senders with a predetermined configuration including the payload format and any of its parameters of a media stream. Thus all parameters are used in a declarative fashion. This can result in different treatment of parameters between offer/answer and declarative usage in RTSP and SAP. This will then need to be pointed out by the payload format specification.
TOC |
The general channel characteristics that RTP flows are experiencing are documented in Section 3 of RFC2736 (Handley, M. and C. Perkins, “Guidelines for Writers of RTP Payload Format Specifications,” December 1999.) [RFC2736]. Below additional information is discussed.
TOC |
At the time of writing the most common IP Maximum Transmission Unit (MTU) of used link layers is 1500 bytes (Ethernet data payload). However there exist links with both smaller MTU and much larger MTUs. Certain parts of Internet do already today support IP MTU of 9000 bytes or more. There is an slow ongoing evolution towards larger MTU sizes. This should be considered in the design, especially in regards to features such as aggregation of independently decodable data units.
TOC |
This section discusses the recommended process to produce an RTP payload format in the described venues. This is to document the best current practice on how to get a well designed and specified payload format as quickly as possible. For specifications that are proprietary or defined by other standards bodies than IETF the primary milestone is registration of the RTP payload format name. However there is also the issue of ensuring best possible quality of any specification.
TOC |
Specification in IETF is recommended for all standardized media formats. The main reason is to provide an openly available RTP payload format specification that also has been reviewed by people experienced with RTP Payload formats. This also assumes that the AVT WG exist.
TOC |
There are a number of steps that an RTP payload format should go through from the initial idea until it is published. This also documents the process that the AVT working group applies when working with RTP payload formats.
TOC |
WG meetings are for discussing issues, not presentations. This means that most RTP payload format should never need to be discussed in a WG meeting. RTP payload formats that would be discussed are either controversial issues that failed to be resolved on the mailing list, or includes new design concepts worth a general discussion.
There exist no requirement to present or discuss a draft at a WG meeting before it becoming published as an RFC. Thus even authors that lack the possibility to go to WG meetings should be able to successfully specify an RTP payload format in IETF. WG meetings may only become required if the draft get stuck in a serious debate that isn't easily resolved.
TOC |
To simplify the work of the AVT WG chairs and its WG members a specific draft file naming convention shall be used for RTP payload formats. Individual submissions shall be named draft-<lead author family name>-avt-rtp-<descriptive name>-<version>. The WG documents shall be named according to this template: draft-ietf-avt-rtp-<descriptive name>-<version>. The inclusion of "avt" in the draft filename ensures that the search for "avt-" will find all AVT related drafts. Inclusion of "rtp" tells us that it is an RTP payload format draft. The descriptive name should be as short as possible while still describe what the payload format is for. It is recommended to use the media format or codec acronym. Please note that the version must start at 00 and is increased by one for each submission to the IETF secretary of the draft. No version numbers may be skipped.
TOC |
There a number of ways of losing a lot of time in the above process. This section discuss what to do and what to avoid.
TOC |
Other standard bodies may define RTP payload in their own specifications. When they do this they are strongly recommend to contact the AVT WG chairs and request review of the work. It is recommended that at least two review steps are performed. One early in the process when more fundamental issues easily can be resolved without abandoning a lot of effort. Then when nearing completion, but while still possible to update the specification as second review should be scheduled. In that pass the quality can be assessed and hopefully no updates are needed. Using this procedure can avoids both conflicting definitions and serious mistakes, like breaking certain aspects of the RTP model.
RTP payload Media Types may be registered in the standards tree by other standard bodies. The requirements on the organization are outlined in the media types registration document (RFC 4855 (Casner, S., “Media Type Registration of RTP Payload Formats,” February 2007.) [RFC4855] and RFC 4288 (Freed, N. and J. Klensin, “Media Type Specifications and Registration Procedures,” December 2005.) [RFC4288]). This registration requires a request to the IESG, which ensures that the registration template is acceptable. To avoid last minute problems with these registration the registration template must be sent for review both to the AVT WG and the media types list (ietf-types@iana.org) and is something that should be included in the IETF reviews of the payload format specification.
Registration of the RTP payload name is something that is required to avoid name collision in the future. Do also note that "x-" names are not suitable for any documented format as they have the same problem with name collision and can't be registered. The list of already registered media types can be found at IANA (http://www.iana.org).
TOC |
Proprietary RTP payload formats are commonly specified when the real-time media format is proprietary and not intended to be part of any standardized system. However there exist many reasons why also proprietary formats should be correctly documented and registered;
To avoid name collisions there is a central register keeping tracks of the registered Media Type names used by different RTP payload formats. When it comes to proprietary formats they should be registered in the vendors own tree. All vendor specific registrations uses sub-type names that start with "vnd.<vendor-name>". All names that uses names in the vendors own trees are not required to be registered with IANA. However registration is recommended if used at all in public environments.
TOC |
The best summary of payload format design is KISS (Keep It Simple, Stupid). A simple payload format makes it easy to review for correctness, implement, and have low complexity. Unfortunately contradicting requirements sometime makes it hard to do things simple. Complexity issues and problems that occur for RTP payload formats are:
- Too many configurations:
- Contradicting requirements results in that one configuration for each conceivable case is created. Such contradicting requirements are often between functionality and bandwidth. This has two big negatives. First all configurations needs to be implemented. Secondly the using application must select the most suitable configuration. Selecting the best configuration can be very difficult and in negotiating applications, this can create interoperability problems. The recommendation is to try to select a very limited (preferable one) configuration that preforms the most common case well and is capable of handling the other cases, but maybe less well.
- Hard to implement:
- Certain payload formats may become difficult to implement both correctly and efficient. This needs to be considered in the design.
- Interaction with general mechanisms:
- Special solutions may create issues with deployed tools for RTP, like tools for robuster transport of RTP. For example the requirement of non broken sequence space creates issues with using both payload type switching and interleaving any mechanism for media independent resilience within the stream.
TOC |
There are number of common features in RTP payload formats. There are no general requirement to support these features, instead their applicability must be considered for each payload format. It might in fact be that certain features are not even applicable.
TOC |
Aggregation allows for the inclusion of multiple ADUs within the same RTP payload. This is commonly supported for codec that produce ADUs of sizes smaller than the IP MTU. Do remember that the MTU may be significantly larger than 1500 bytes, 9000 bytes is available today and a MTU of 64k may be available in the future. Many speech codecs have the property of ADUs of a few fixed sizes. Video encoders generally may produce ADUs of quite flexible size. Thus the need for aggregation may be less. However in certain use cases the possibility to aggregate multiple ADUs especially for different playback times are useful.
The main disadvantage of aggregation is the extra delay introduced, due to buffering until sufficient amount of ADUs have been collected and reduced robustness against packet loss. It also introduces buffering requirements on the receiver.
TOC |
If the real-time media format has the property that it may produce ADUs that are larger than common MTUs sizes then fragmentation support should be considered. An RTP Payload format may always fall back on IP fragmentation, however as discussed in RFC 2736 this have some drawbacks. The usage of RTP payload format level fragmentation, does primarily allow for more efficient usage of RTP packet loss recovery mechanisms. However it may in some cases also allow usage of the partial ADU by doing media specific fragmentation at media specific boundaries.
TOC |
Interleaving has been implemented in a number of payload formats to allow for less quality reduction when packet loss occurs. When losses are bursty and several consecutive packets are lost, the impact on quality can be quite severe. Interleaving is used to convert that burst loss to several spread out individual losses. It can also be used when several ADUs are aggregated in the same packets. A loss of an RTP packet with several ADUs in the payload has the same affect as a burst loss if the ADUs would have been transmitted in individual packets. To reduce the burstiness of the loss, the data present in an aggregated payload may be interleaved, thus spread the loss over a longer time period.
A requirement for doing interleaving within an RTP payload format is the aggregation of multiple ADUs. For formats that don't use aggregation there is still the possibility to implement an transmission order re-scheduling mechanism. That have the effect that packets transmitted next to each other originates from different points in the media stream. This can be used to mitigate burst losses, which may be useful if one transmit packets with small intervals. However it may also be used to transmit more significant data earlier in combination with RTP retransmission to allow for more graceful degradation and increased possibilities to receive the most important data, e.g. Intra frames of video.
The drawbacks of interleaving is the significantly increased transmission buffering delay, making it mostly useless for low delay applications. It also creates significant buffering requirements on the receiver. That buffering also is problematic as it is usually difficult to indicate when a receiver may start consume data and still avoid buffer underrun caused by the interleaving mechanism itself. The transmission re-scheduling is only useful in a few specific cases, like in streaming with retransmissions. This must be weighted against the complexity of these schemes.
TOC |
A few RTP payload format have implemented back channels within the media format. Those have been for specific features, like the AMR (Sjoberg, J., Westerlund, M., Lakaniemi, A., and Q. Xie, “RTP Payload Format and File Storage Format for the Adaptive Multi-Rate (AMR) and Adaptive Multi-Rate Wideband (AMR-WB) Audio Codecs,” April 2007.) [RFC4867] codec mode request (CMR) field. The CMR field is used in gateway operations to circuit switched voice to allow an IP terminal to react to the CS networks need for a specific encoder mode. A common property for the media back channels is the need to have this signalling in direct relation to the media or the media path.
If back channels are considered for an RTP payload format they should be for specific mechanism and which can't be easily satisfied by more generic mechanisms within RTP or RTCP.
TOC |
There exist some codecs that supports some type of scalability, i.e. where additional data can be used to improve media stream properties, but the additional data isn't required for decoding. This quality improvements has been so far been in a number of different types:
- Temporal:
- For video codecs increased frame rate is one way to improve the quality. Audio codecs could provide increase sampling rate.
- Spatial:
- Video codecs with scalability may increase the resolution or image size.
- Quality:
- The perceived quality of the media stream can be improved without affecting the temporal or spatial properties of the media. This is usually done by improving the signal to noise ration within the content.
Codecs that support scalability are at the time of writing this having a bit of revival. It has been realized that getting the need functionality for the media stream in the RTP framework is quite challenging. The author hopes to be able to provide some lessons from this work in this document in the future.
TOC |
Some media codecs requires high packet rates, and in these cases the RTP sequence number wraps to quickly. As rule of thumb, the sequence number space must not be possible to wrap in less than 2 minutes (TCP maximum segment lifetime). If that may occur then the payload format should specify a extended sequence number field to allow the receiver to determine where a specific payload belongs in the sequence also in the face of extensive reordering. The RTP payload format for uncompressed video [RFC4175] (Gharai, L. and C. Perkins, “RTP Payload Format for Uncompressed Video,” September 2005.) can be used as an example for such a field.
TOC |
This section provides a few examples of payload formats that is worth noting for good design in general or specific details.
TOC |
The AMR (Sjoberg, J., Westerlund, M., Lakaniemi, A., and Q. Xie, “RTP Payload Format and File Storage Format for the Adaptive Multi-Rate (AMR) and Adaptive Multi-Rate Wideband (AMR-WB) Audio Codecs,” April 2007.) [RFC4867], AMR-WB (Sjoberg, J., Westerlund, M., Lakaniemi, A., and Q. Xie, “RTP Payload Format and File Storage Format for the Adaptive Multi-Rate (AMR) and Adaptive Multi-Rate Wideband (AMR-WB) Audio Codecs,” April 2007.) [RFC4867], EVRC (Li, A., “RTP Payload Format for Enhanced Variable Rate Codecs (EVRC) and Selectable Mode Vocoders (SMV),” July 2003.) [RFC3558], SMV (Li, A., “RTP Payload Format for Enhanced Variable Rate Codecs (EVRC) and Selectable Mode Vocoders (SMV),” July 2003.) [RFC3558] payload format are all quite similar. They are all for frame based audio codecs and use a table of content structure. Each frame has a table of contents entry that indicate the type of the frame and if additional frames are present. This is quite flexible but produces unnecessary overhead if the ADU is fixed size and when aggregating multiple ones they are commonly of the same type. In that case a solution like that in AMR-WB+ (Sjoberg, J., Westerlund, M., Lakaniemi, A., and S. Wenger, “RTP Payload Format for the Extended Adaptive Multi-Rate Wideband (AMR-WB+) Audio Codec,” January 2006.) [RFC4352] maybe more suitable.
AMR-WB+ does contain one less good feature which is depending on the media codec itself. The media codec produces a large range of different frame lengths in time perspective. The RTP timestamp rate is selected to the very unusual value of 72 kHz despite that output normally is at sample rate of 48kHz. This timestamp rate is the smallest found value that would make all of the frames the codec could produce results in integer frame length in RTP timestamp ticks. That way a receiver can always correctly place the frames in relation to any other frame, also at frame length changes. The down side is that the decoder output for certain frame lengths are in fact partial samples. Resulting in that the output in samples from the codec will vary from frame to frame, potentially making implementation more difficult.
The RTP payload format for MIDI [RFC4695] (Lazzaro, J. and J. Wawrzynek, “RTP Payload Format for MIDI,” November 2006.) contains some interesting features. MIDI is an audio format sensitive to packet losses, as the loss of a note off command will result in that a note will be stuck in an on state. To counter this a recovery journal is defined that provides a summarized state that allows the receiver to recover from packet losses quickly. It also uses RTCP and the reported highest sequence number to be able to prune the state the recovery journal needs to contain. These features appears limited in applicability for media formats that are highly stateful and primarily uses symbolic media representations.
TOC |
The definition of RTP payload formats for video has seen an evolution from the early ones such as H.261 towards the latest for VC-1 and H.264.
The H.264 RTP payload format [RFC3984] (Wenger, S., Hannuksela, M., Stockhammer, T., Westerlund, M., and D. Singer, “RTP Payload Format for H.264 Video,” February 2005.) can be seen as a smorgasbord of functionality, some pretty advanced as the interleaving. The reason for this was to ensure that the majority of applications considered by the ITU-T and MPEG that can be supported by RTP was supported. This has created a payload format that rarely is implemented in its completeness. Despite that no major issues with interoperability has been reported. However, there are common complaints about its complexity.
The RTP payload format for uncompressed video [RFC4175] (Gharai, L. and C. Perkins, “RTP Payload Format for Uncompressed Video,” September 2005.) is basically required to be mentioned in this context as it contains a special feature not commonly seen in RTP payload formats. Due to the high bit-rate and thus packet rate of uncompressed video (gigabits rather than megabits) the payload format include a field to extend the RTP sequence number as the normal 16-bit one can wrap in below a second. It also specifies a registry of different color sub-sampling that can be re-used in other video RTP payload formats.
TOC |
There would be overstating that there exist a trend in text payload formats as only a single format actually carrying a text format has been standardized in IETF, namely T.140 [RFC4103] (Hellstrom, G. and P. Jones, “RTP Payload for Text Conversation,” June 2005.). The 3GPP Timed Text format [RFC4396] (Rey, J. and Y. Matsui, “RTP Payload Format for 3rd Generation Partnership Project (3GPP) Timed Text,” February 2006.) could be considered to be text, despite it in the end was registered as a video format. This is decorated text, usable for subtitles and other embellishments of video which is why it ended up being registered as video format. However, it has many of the properties that text formats in generally have.
The RTP payload format for T.140 was designed with high reliability in mind as real-time text commonly are a extremely low-bit rate application. Thus, it recommends the use of RFC 2190 with many redundancy generations. However, the format failed to provide a text block specific sequence number and relies instead of the RTP one to detection loss. This makes detection of missing text blocks unnecessarily difficult and hinders the deployment with other robustness mechanisms that would switch the payload type as that may result in erroneous error marking in the T.140 text stream.
TOC |
There a number of sections in the payload format draft that needs some special considerations. These include security and IANA considerations.
TOC |
All Internet drafts requires a Security Consideration section. The security consideration section in an RTP payload format needs to concentrate on the security properties this particular format has. Some payload format has very little specific issues or properties and can fully fall back on the general RTP and used profile's security considerations. Due to that these are always applicable, a reference to these are normally placed first in the security consideration section. There is suggested text in the template below.
The security issues of confidentiality, integrity protection and source authentication are common issues for all payload formats. These should be solved by payload external mechanism and does not need any special consideration in the payload format except for an reminder on these issues. A suitable stock text to inform people about this is included in the template.
Potential security issues with an RTP payload format and the media encoding that needs to be considered are:
Suitable stock text for the security consideration is provided in the template. However the authors do need to actively consider any security issues from the start. Failure to address these issues is blocking approval and publication.
TOC |
RTP and its profiles do discuss congestion control. Congestion control is an important issue in any usage in non-dedicated networks. For that reason all RTP payload formats are recommended to discuss the possibilities that exist to regulate the bit-rate of the transmissions using the described RTP payload format. Some formats may have limited or step wise regulation of bit-rate. Such limiting factor should be discussed.
TOC |
Due to that all RTP Payload format contains a Media Type specification they also need an IANA consideration section. The media type name must be registered and this is done by requesting that IANA register that media name. When that registration request is written it shall also be requested that the media type is included under the "RTP Payload Format MIME types" list part of the RTP registry.
In addition to the above request for media type registration some payload formats may have parameters where in the future new parameter values needs to be added. In these cases a registry for that parameter must be created. This is done by defining the registry in the IANA consideration section. BCP 26 (RFC 5226) (Narten, T. and H. Alvestrand, “Guidelines for Writing an IANA Considerations Section in RFCs,” May 2008.) [RFC5226] provides guidelines to writing such registries. Care should be taken when defining the policy for new registrations.
Before writing a new registry it is worth checking the existing ones in the IANA "MIME Media Type Sub-Parameter Registries". For example video formats needing a media parameter expressing color sub-sampling may be able to reuse those defined for video/raw (Gharai, L. and C. Perkins, “RTP Payload Format for Uncompressed Video,” September 2005.) [RFC4175].
TOC |
This section informs and recommends some tools that may be used. Don't be pressured to follow these recommendation. There exist a number of alternatives. But these suggestion is worth checking out before deciding that the field is greener somewhere else.
TOC |
There is many choices when it comes to tools to choose for authoring Internet drafts. However in the end they needs to be able to produce a draft that conforms to the Internet drafts requirements. If you don't have any previous experience with authoring Internet drafts XML2RFC do have some advantages. It helps creating a lot of the necessary boiler plate in accordance with the latest rules. Thus reducing the effort. It also speeds up the publication after approval as the RFC-editor can use the source XML document to quicker produce the RFC.
Another common choice is to use Microsoft Word and a suitable template, see [RFC3285] (Gahrns, M. and T. Hain, “Using Microsoft Word to create Internet Drafts and RFCs,” May 2002.) to produce the draft and print that using the generic text printer. It has some advantage when it comes to spell checking and change bars. However Word may also produce some problems, like changing formating, inconsistent result between what one sees in the editor and in the generated text document, at least according to the authors personal experience.
TOC |
There are few tools that are very good to know about when writing an draft. These help check and verify parts of ones work. These tools can be found at http://tools.ietf.org.
TOC |
This document currently has a few open issues that needs resolving before publication:
TOC |
This document makes no request of IANA.
Note to RFC Editor: this section may be removed on publication as an RFC.
TOC |
As this is an informational document on the writing of drafts intended to be RFCs there is no direct security considerations. However the document does discuss the writing of security consideration sections and what should be particular considered when specifying RTP payload formats.
TOC |
Note to RFC Editor: This section may be removed after carrying out all the instructions of this section.
TOC |
The author would like to thank the individuals that has provided input to this document. These individuals include: John Lazzaro.
TOC |
[CSP-RTP] | Colin , “RTP: Audio and Video for the Internet,” June 2003. |
[MACOSFILETYPES] | Apple Knowledge Base Article 55381<http://www.info.apple.com/kbnum/n55381>, “Mac OS: File Type and Creator Codes, and File Formats,” 1993. |
[RFC-ED] | http://www.rfc-editor.org/policy.html, “RFC Editorial Guidelines and Procedures,” July 2008. |
[RFC1305] | Mills, D., “Network Time Protocol (Version 3) Specification, Implementation,” RFC 1305, March 1992 (TXT, PDF). |
[RFC2026] | Bradner, S., “The Internet Standards Process -- Revision 3,” BCP 9, RFC 2026, October 1996 (TXT). |
[RFC2198] | Perkins, C., Kouvelas, I., Hodson, O., Hardman, V., Handley, M., Bolot, J., Vega-Garcia, A., and S. Fosse-Parisis, “RTP Payload for Redundant Audio Data,” RFC 2198, September 1997 (TXT, HTML, XML). |
[RFC2326] | Schulzrinne, H., Rao, A., and R. Lanphier, “Real Time Streaming Protocol (RTSP),” RFC 2326, April 1998 (TXT). |
[RFC2360] | Scott, G., “Guide for Internet Standards Writers,” BCP 22, RFC 2360, June 1998 (TXT, HTML, XML). |
[RFC2418] | Bradner, S., “IETF Working Group Guidelines and Procedures,” BCP 25, RFC 2418, September 1998 (TXT, HTML, XML). |
[RFC2508] | Casner, S. and V. Jacobson, “Compressing IP/UDP/RTP Headers for Low-Speed Serial Links,” RFC 2508, February 1999 (TXT). |
[RFC2616] | Fielding, R., Gettys, J., Mogul, J., Frystyk, H., Masinter, L., Leach, P., and T. Berners-Lee, “Hypertext Transfer Protocol -- HTTP/1.1,” RFC 2616, June 1999 (TXT, PS, PDF, HTML, XML). |
[RFC2736] | Handley, M. and C. Perkins, “Guidelines for Writers of RTP Payload Format Specifications,” BCP 36, RFC 2736, December 1999 (TXT). |
[RFC2959] | Baugher, M., Strahm, B., and I. Suconick, “Real-Time Transport Protocol Management Information Base,” RFC 2959, October 2000 (TXT). |
[RFC2974] | Handley, M., Perkins, C., and E. Whelan, “Session Announcement Protocol,” RFC 2974, October 2000 (TXT). |
[RFC3095] | Bormann, C., Burmeister, C., Degermark, M., Fukushima, H., Hannu, H., Jonsson, L-E., Hakenberg, R., Koren, T., Le, K., Liu, Z., Martensson, A., Miyazaki, A., Svanbro, K., Wiebke, T., Yoshimura, T., and H. Zheng, “RObust Header Compression (ROHC): Framework and four profiles: RTP, UDP, ESP, and uncompressed,” RFC 3095, July 2001 (TXT). |
[RFC3261] | Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, “SIP: Session Initiation Protocol,” RFC 3261, June 2002 (TXT). |
[RFC3264] | Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” RFC 3264, June 2002 (TXT). |
[RFC3285] | Gahrns, M. and T. Hain, “Using Microsoft Word to create Internet Drafts and RFCs,” RFC 3285, May 2002 (TXT). |
[RFC3410] | Case, J., Mundy, R., Partain, D., and B. Stewart, “Introduction and Applicability Statements for Internet-Standard Management Framework,” RFC 3410, December 2002 (TXT). |
[RFC3545] | Koren, T., Casner, S., Geevarghese, J., Thompson, B., and P. Ruddy, “Enhanced Compressed RTP (CRTP) for Links with High Delay, Packet Loss and Reordering,” RFC 3545, July 2003 (TXT). |
[RFC3550] | Schulzrinne, H., Casner, S., Frederick, R., and V. Jacobson, “RTP: A Transport Protocol for Real-Time Applications,” STD 64, RFC 3550, July 2003 (TXT, PS, PDF). |
[RFC3551] | Schulzrinne, H. and S. Casner, “RTP Profile for Audio and Video Conferences with Minimal Control,” STD 65, RFC 3551, July 2003 (TXT, PS, PDF). |
[RFC3558] | Li, A., “RTP Payload Format for Enhanced Variable Rate Codecs (EVRC) and Selectable Mode Vocoders (SMV),” RFC 3558, July 2003 (TXT). |
[RFC3569] | Bhattacharyya, S., “An Overview of Source-Specific Multicast (SSM),” RFC 3569, July 2003 (TXT). |
[RFC3577] | Waldbusser, S., Cole, R., Kalbfleisch, C., and D. Romascanu, “Introduction to the Remote Monitoring (RMON) Family of MIB Modules,” RFC 3577, August 2003 (TXT). |
[RFC3611] | Friedman, T., Caceres, R., and A. Clark, “RTP Control Protocol Extended Reports (RTCP XR),” RFC 3611, November 2003 (TXT). |
[RFC3711] | Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K. Norrman, “The Secure Real-time Transport Protocol (SRTP),” RFC 3711, March 2004 (TXT). |
[RFC3828] | Larzon, L-A., Degermark, M., Pink, S., Jonsson, L-E., and G. Fairhurst, “The Lightweight User Datagram Protocol (UDP-Lite),” RFC 3828, July 2004 (TXT). |
[RFC3979] | Bradner, S., “Intellectual Property Rights in IETF Technology,” BCP 79, RFC 3979, March 2005 (TXT). |
[RFC3984] | Wenger, S., Hannuksela, M., Stockhammer, T., Westerlund, M., and D. Singer, “RTP Payload Format for H.264 Video,” RFC 3984, February 2005 (TXT). |
[RFC4103] | Hellstrom, G. and P. Jones, “RTP Payload for Text Conversation,” RFC 4103, June 2005 (TXT). |
[RFC4170] | Thompson, B., Koren, T., and D. Wing, “Tunneling Multiplexed Compressed RTP (TCRTP),” BCP 110, RFC 4170, November 2005 (TXT). |
[RFC4175] | Gharai, L. and C. Perkins, “RTP Payload Format for Uncompressed Video,” RFC 4175, September 2005 (TXT). |
[RFC4288] | Freed, N. and J. Klensin, “Media Type Specifications and Registration Procedures,” BCP 13, RFC 4288, December 2005 (TXT). |
[RFC4301] | Kent, S. and K. Seo, “Security Architecture for the Internet Protocol,” RFC 4301, December 2005 (TXT). |
[RFC4347] | Rescorla, E. and N. Modadugu, “Datagram Transport Layer Security,” RFC 4347, April 2006 (TXT). |
[RFC4352] | Sjoberg, J., Westerlund, M., Lakaniemi, A., and S. Wenger, “RTP Payload Format for the Extended Adaptive Multi-Rate Wideband (AMR-WB+) Audio Codec,” RFC 4352, January 2006 (TXT). |
[RFC4396] | Rey, J. and Y. Matsui, “RTP Payload Format for 3rd Generation Partnership Project (3GPP) Timed Text,” RFC 4396, February 2006 (TXT). |
[RFC4566] | Handley, M., Jacobson, V., and C. Perkins, “SDP: Session Description Protocol,” RFC 4566, July 2006 (TXT). |
[RFC4571] | Lazzaro, J., “Framing Real-time Transport Protocol (RTP) and RTP Control Protocol (RTCP) Packets over Connection-Oriented Transport,” RFC 4571, July 2006 (TXT). |
[RFC4585] | Ott, J., Wenger, S., Sato, N., Burmeister, C., and J. Rey, “Extended RTP Profile for Real-time Transport Control Protocol (RTCP)-Based Feedback (RTP/AVPF),” RFC 4585, July 2006 (TXT). |
[RFC4588] | Rey, J., Leon, D., Miyazaki, A., Varsa, V., and R. Hakenberg, “RTP Retransmission Payload Format,” RFC 4588, July 2006 (TXT). |
[RFC4648] | Josefsson, S., “The Base16, Base32, and Base64 Data Encodings,” RFC 4648, October 2006 (TXT). |
[RFC4677] | Hoffman, P. and S. Harris, “The Tao of IETF - A Novice's Guide to the Internet Engineering Task Force,” RFC 4677, September 2006 (TXT). |
[RFC4695] | Lazzaro, J. and J. Wawrzynek, “RTP Payload Format for MIDI,” RFC 4695, November 2006 (TXT). |
[RFC4855] | Casner, S., “Media Type Registration of RTP Payload Formats,” RFC 4855, February 2007 (TXT). |
[RFC4867] | Sjoberg, J., Westerlund, M., Lakaniemi, A., and Q. Xie, “RTP Payload Format and File Storage Format for the Adaptive Multi-Rate (AMR) and Adaptive Multi-Rate Wideband (AMR-WB) Audio Codecs,” RFC 4867, April 2007 (TXT). |
[RFC4975] | Campbell, B., Mahy, R., and C. Jennings, “The Message Session Relay Protocol (MSRP),” RFC 4975, September 2007 (TXT). |
[RFC5109] | Li, A., “RTP Payload Format for Generic Forward Error Correction,” RFC 5109, December 2007 (TXT). |
[RFC5124] | Ott, J. and E. Carrara, “Extended Secure RTP Profile for Real-time Transport Control Protocol (RTCP)-Based Feedback (RTP/SAVPF),” RFC 5124, February 2008 (TXT). |
[RFC5226] | Narten, T. and H. Alvestrand, “Guidelines for Writing an IANA Considerations Section in RFCs,” BCP 26, RFC 5226, May 2008 (TXT). |
[RFC5246] | Dierks, T. and E. Rescorla, “The Transport Layer Security (TLS) Protocol Version 1.2,” RFC 5246, August 2008 (TXT). |
[RFC5378] | Bradner, S. and J. Contreras, “Rights Contributors Provide to the IETF Trust,” BCP 78, RFC 5378, November 2008 (TXT). |
TOC |
This section contains a template for writing an RTP payload format in form as a Internet draft. Text within [...] are instructions and must be removed. Some text proposals that are included are conditional. "..." is used to indicate where further text should be written.
TOC |
[The title shall be descriptive but as compact as possible. RTP is allowed and recommended abbreviation in the title]
RTP Payload format for ...
TOC |
Status of this Memo
[Insert the IPR notice and copyright boiler plate from BCP 78 and 79 that applies to this draft.]
[Insert the current Internet Draft document explanation. At the time of publishing it was:]
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts.
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."
[Insert the ID list and shadow list reference. At the time of publishing it was:]
The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html.
[Optionally: Select either of these paragraphs depending on draft status]
This document is an individual submission to the IETF. Comments should be directed to the authors.
This document is a submission of the IETF AVT WG. Comments should be directed to the AVT WG mailing list, avt@ietf.org.
TOC |
[An payload format abstract should mention the capabilities of the format, for which media format is used, and a little about that codec formats capabilities. Any abbreviation used in the payload format must be spelled out here except the very well known like RTP. No references are allowed, no use of RFC 2119 language either.]
TOC |
[All drafts over 15 pages in length must have an Table of Content.]
TOC |
[The introduction should provide a background and overview of the payload formats capabilities. No normative language in this section, i.e. no MUST, SHOULDs etc.]
TOC |
[Define conventions, definitions and acronyms used in the document in this section. The most common definition used in RTP Payload formats are the RFC 2119 definitions of the upper case normative words, e.g. MUST and SHOULD.]
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119.
RFC-editor note: RFCXXXX is to be replaced by the RFC number this specification recieves when published.
TOC |
[The intention of this section is to enable reviewers and persons to get an overview of the capabilities and major properties of the media format. It should be kept short and concise and is not a complete replacement for reading the media format specification.]
TOC |
[Overview of payload structure]
TOC |
[RTP header usage needs to be defined. The fields that absolutely need to be defined are timestamp and marker bit. Further field may be specified if used. All the rest should be left to their RTP specification definition]
The remaining RTP header fields are used as specified in RFC 3550.
TOC |
[Define how the payload header, if it exist, is structured and used.]
TOC |
[The payload data, i.e. what the media codec has produced. Commonly done through reference to media codec specification which defines how the data is structured. Rules for padding may need to be defined to bring data to octet alignment.]
TOC |
[One or more examples are good to help ease the understanding of the RTP payload format.]
TOC |
[This section is to describe the possibility to vary the bit-rate as a response to congestion. Below is also a proposal for an initial text that reference RTP and profiles definition of congestion control.]
Congestion control for RTP SHALL be used in accordance with RFC 3550 (Schulzrinne, H., Casner, S., Frederick, R., and V. Jacobson, “RTP: A Transport Protocol for Real-Time Applications,” July 2003.) [RFC3550], and with any applicable RTP profile; e.g., RFC 3551 (Schulzrinne, H. and S. Casner, “RTP Profile for Audio and Video Conferences with Minimal Control,” July 2003.) [RFC3551]. An additional requirement if best-effort service is being used is: users of this payload format MUST monitor packet loss to ensure that the packet loss rate is within acceptable parameters.
TOC |
This RTP payload format is identified using the ... media type which is registered in accordance with RFC 4855 (Casner, S., “Media Type Registration of RTP Payload Formats,” February 2007.) [RFC4855] and using the template of RFC 4288 (Freed, N. and J. Klensin, “Media Type Specifications and Registration Procedures,” December 2005.) [RFC4288].
TOC |
[Here the media type registration template from RFC 4288 is placed and filled out. This template is provided with some common RTP boilerplate.]
Type name:
Subtype name:
Required parameters:
Optional parameters:
Encoding considerations:
This media type is framed and binary, see section 4.8 in RFC4288 (Freed, N. and J. Klensin, “Media Type Specifications and Registration Procedures,” December 2005.) [RFC4288].
Security considerations:
Please see security consideration in RFCXXXX
Interoperability considerations:
Published specification:
Applications that use this media type:
Additional information:
Magic number(s):
File extension(s):
Macintosh file type code(s):
Person & email address to contact for further information:
Intended usage: (One of COMMON, LIMITED USE or OBSOLETE.)
Restrictions on usage:
[The below text is for media types that is only defined for RTP payload formats. There exist certain media types that are defined both as RTP payload formats and file transfer. The rules for such types are documented in RFC 4855 (Casner, S., “Media Type Registration of RTP Payload Formats,” February 2007.) [RFC4855].]
This media type depends on RTP framing, and hence is only defined for transfer via RTP [RFC3550]. Transport within other framing protocols is not defined at this time.
Author:
Change controller:
IETF Audio/Video Transport working group delegated from the IESG.
(Any other information that the author deems interesting may be added below this line.)
[From RFC 4288: Some discussion of Macintosh file type codes and their purpose can be found in [MACOSFILETYPES] (Apple Knowledge Base Article 55381<http://www.info.apple.com/kbnum/n55381>, “Mac OS: File Type and Creator Codes, and File Formats,” 1993.). Additionally, please refrain from writing "none" or anything similar when no file extension or Macintosh file type is specified, lest "none" be confused with an actual code value.]
TOC |
The mapping of the above defined payload format media type and its parameters SHALL be done according to Section 3 of RFC 4855 (Casner, S., “Media Type Registration of RTP Payload Formats,” February 2007.) [RFC4855].
[More specific rules only need to be included if some parameter does not match these rules.]
TOC |
[Here write your offer/answer consideration section, please see Section Section 3.3.2.1 (The Offer/Answer Model) for help.]
TOC |
[Here write your considerations for declarative SDP, please see Section Section 3.3.2.2 (Declarative usage in RTSP and SAP) for help.]
TOC |
This memo requests that IANA registers [insert media type name here] as specified in Appendix A.11.1 (Media Type Definition). The media type is also requested to be added to the IANA registry for "RTP Payload Format MIME types" (http://www.iana.org/assignments/rtp-parameters).
[See Section Section 7.3 (IANA Consideration) and consider if any of the parameter needs a registered name space.]
TOC |
[See Section Section 7.1 (Security Consideration)]
RTP packets using the payload format defined in this specification are subject to the security considerations discussed in the RTP specification (Schulzrinne, H., Casner, S., Frederick, R., and V. Jacobson, “RTP: A Transport Protocol for Real-Time Applications,” July 2003.) [RFC3550] , and in any applicable RTP profile. The main security considerations for the RTP packet carrying the RTP payload format defined within this memo are confidentiality, integrity and source authenticity. Confidentiality is achieved by encryption of the RTP payload. Integrity of the RTP packets through suitable cryptographic integrity protection mechanism. Cryptographic system may also allow the authentication of the source of the payload. A suitable security mechanism for this RTP payload format should provide confidentiality, integrity protection and at least source authentication capable of determining if an RTP packet is from a member of the RTP session or not.
Note that the appropriate mechanism to provide security to RTP and payloads following this memo may vary. It is dependent on the application, the transport, and the signalling protocol employed. Therefore a single mechanism is not sufficient, although if suitable the usage of SRTP (Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K. Norrman, “The Secure Real-time Transport Protocol (SRTP),” March 2004.) [RFC3711] is recommended. Other mechanism that may be used are IPsec (Kent, S. and K. Seo, “Security Architecture for the Internet Protocol,” December 2005.) [RFC4301] and TLS (Dierks, T. and E. Rescorla, “The Transport Layer Security (TLS) Protocol Version 1.2,” August 2008.) [RFC5246] (RTP over TCP), but also other alternatives may exist.
This RTP payload format and its media decoder do not exhibit any significant non-uniformity in the receiver-side computational complexity for packet processing, and thus are unlikely to pose a denial-of-service threat due to the receipt of pathological data. Nor does the RTP payload format contain any active content.
[The previous paragraph may need editing due to the format breaking either of the statements. Fill in here any further potential security threats]
TOC |
[References must be classified as either normative or informative and added to the relevant section. References should use descriptive reference tags.]
TOC |
[Normative references are those that are required to be used to correctly implement the payload format.]
TOC |
[All other references.]
TOC |
[All Authors need to include their Name and email addresses as a minimal. Commonly also surface mail and possibly phone numbers are included.]
TOC |
Magnus Westerlund | |
Ericsson | |
Torshamgatan 23 | |
Stockholm, SE-164 80 | |
SWEDEN | |
Phone: | +46 8 7190000 |
Fax: | +46 8 757 55 50 |
Email: | magnus.westerlund@ericsson.com |