INTERNET-DRAFT A. Malis, ed. Obsoletes: 5787 (if approved) Verizon Communications Updates: 5786 A. Lindem, ed. Intended Status: Proposed Standard Ericsson Expires: December 19, 2012 D. Papadimitriou, ed. Alcatel-Lucent June 19, 2012 ASON Routing for OSPFv2 Protocols draft-ietf-ccamp-rfc5787bis-04.txt Status of this Memo This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/1id-abstracts.html The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html Copyright and License Notice Copyright (c) 2012 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as Malis Expires December 19, 2012 [Page 1] INTERNET DRAFT RFC5787bis June 19, 2012 described in the Simplified BSD License. Malis Expires December 19, 2012 [Page 2] INTERNET DRAFT RFC5787bis June 19, 2012 Abstract The ITU-T has defined an architecture and requirements for operating an Automatically Switched Optical Network (ASON). The Generalized Multiprotocol Label Switching (GMPLS) protocol suite is designed to provide a control plane for a range of network technologies including optical networks such as time division multiplexing (TDM) networks including SONET/SDH and Optical Transport Networks (OTNs), and lambda switching optical networks. The requirements for GMPLS routing to satisfy the requirements of ASON routing, and an evaluation of existing GMPLS routing protocols are provided in other documents. This document defines extensions to the OSPFv2 Link State Routing Protocol to meet the requirements for routing in an ASON. Note that this work is scoped to the requirements and evaluation expressed in RFC 4258 and RFC 4652 and the ITU-T Recommendations current when those documents were written. Future extensions of revisions of this work may be necessary if the ITU-T Recommendations are revised or if new requirements are introduced into a revision of RFC 4258. This document obsoletes RFC 5787 and updates RFC 5786. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.1. Conventions Used in This Document . . . . . . . . . . . . 6 2. Routing Areas, OSPF Areas, and Protocol Instances . . . . . . 6 3. Terminology and Identification . . . . . . . . . . . . . . . . 7 4. Reachability . . . . . . . . . . . . . . . . . . . . . . . . . 7 5. Link Attribute . . . . . . . . . . . . . . . . . . . . . . . . 8 5.1. Local Adaptation . . . . . . . . . . . . . . . . . . . . . 8 5.2. Bandwidth Accounting . . . . . . . . . . . . . . . . . . . 9 6. Routing Information Scope . . . . . . . . . . . . . . . . . . 9 6.1. Link Advertisement (Local and Remote TE Router ID Sub-TLV) . . . . . . . . . . . . . . . . . . . . . . . . . 10 6.2. Reachability Advertisement (Local TE Router ID sub-TLV) . 11 7. Routing Information Dissemination . . . . . . . . . . . . . . 12 7.1 Import/Export Rules . . . . . . . . . . . . . . . . . . . . 12 7.2 Loop Prevention . . . . . . . . . . . . . . . . . . . . . . 12 7.2.1 Inter-RA Export Upward/Downward Sub-TLVs . . . . . . . 13 7.2.2 Inter-RA Export Upward/Downward Sub-TLV Processing . . 14 8. OSPFv2 Scalability . . . . . . . . . . . . . . . . . . . . . . 14 9. Security Considerations . . . . . . . . . . . . . . . . . . . 15 10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 15 10.1. Sub-TLVs of the Link TLV . . . . . . . . . . . . . . . . 15 Malis Expires December 19, 2012 [Page 3] INTERNET DRAFT RFC5787bis June 19, 2012 10.2. Sub-TLVs of the Node Attribute TLV . . . . . . . . . . . 16 10.3. Sub-TLVs of the Router Address TLV . . . . . . . . . . . 16 11. Management Considerations . . . . . . . . . . . . . . . . . 17 11.1. Routing Area (RA) Isolation . . . . . . . . . . . . . . . 17 11.2 Routing Area (RA) Topology/Configuration Changes . . . . . 17 12. Comparison to Requirements in RFC 4258 . . . . . . . . . . . 17 13. References . . . . . . . . . . . . . . . . . . . . . . . . . 23 13.1. Normative References . . . . . . . . . . . . . . . . . . 23 13.2. Informative References . . . . . . . . . . . . . . . . . 24 14. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 25 Appendix A. ASON Terminology . . . . . . . . . . . . . . . . . . 26 Appendix B. ASON Routing Terminology . . . . . . . . . . . . . . 27 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 28 Malis Expires December 19, 2012 [Page 4] INTERNET DRAFT RFC5787bis June 19, 2012 1. Introduction The Generalized Multiprotocol Label Switching (GMPLS) [RFC3945] protocol suite is designed to provide a control plane for a range of network technologies including optical networks such as time division multiplexing (TDM) networks including SONET/SDH and Optical Transport Networks (OTNs), and lambda switching optical networks. The ITU-T defines the architecture of the Automatically Switched Optical Network (ASON) in [G.8080]. [RFC4258] describes the routing requirements for the GMPLS suite of routing protocols to support the capabilities and functionality of ASON control planes identified in [G.7715] and in [G.7715.1]. [RFC4652] evaluates the IETF Link State routing protocols against the requirements identified in [RFC4258]. Section 7.1 of [RFC4652] summarizes the capabilities to be provided by OSPFv2 [RFC2328] in support of ASON routing. This document describes the OSPFv2 specifics for ASON routing. Multi-layer transport networks are constructed from multiple networks of different technologies operating in a client-server relationship. The ASON routing model includes the definition of routing levels that provide scaling and confidentiality benefits. In multi-level routing, domains called routing areas (RAs) are arranged in a hierarchical relationship. Note that as described in [RFC4652], there is no implied relationship between multi-layer transport networks and multi-level routing. The multi-level routing mechanisms described in this document work for both single-layer and multi-layer networks. Implementations may support a hierarchical routing topology (multi- level) for multiple transport network layers and/or a hierarchical routing topology for a single transport network layer. This document describes the processing of the generic (technology- independent) link attributes that are defined in [RFC3630], [RFC4202], and [RFC4203] and that are extended in this document. As described in Section 5.2, technology-specific traffic engineering attributes and their processing may be defined in other documents that complement this document. Note that this work is scoped to the requirements and evaluation expressed in [RFC4258] and [RFC4652] and the ITU-T Recommendations current when those documents were written. Future extensions of revisions of this work may be necessary if the ITU-T Recommendations are revised or if new requirements are introduced into a revision of Malis Expires December 19, 2012 [Page 5] INTERNET DRAFT RFC5787bis June 19, 2012 [RFC4258]. 1.1. Conventions Used in This Document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. The reader is assumed to be familiar with the terminology and requirements developed in [RFC4258] and the evaluation outcomes described in [RFC4652]. General ASON terminology is provided in Appendix A. ASON routing terminology is described in Appendix B. 2. Routing Areas, OSPF Areas, and Protocol Instances An ASON routing area (RA) represents a partition of the data plane, and its identifier is used within the control plane as the representation of this partition. RAs are hierarchically contained: a higher-level (parent) RA contains lower-level (child) RAs that in turn MAY also contain RAs. Thus, RAs contain RAs that recursively define successive hierarchical RA levels. Routing information may be exchanged between levels of the RA hierarchy, i.e., Level N+1 and N, where Level N represents the RAs contained by Level N+1. The links connecting RAs may be viewed as external links (inter-RA links), and the links representing connectivity within an RA may be viewed as internal links (intra-RA links). The external links to an RA at one level of the hierarchy may be internal links in the parent RA. Intra-RA links of a child RA MAY be hidden from the parent RA's view. [RFC4258] An ASON RA can be mapped to an OSPF area, but the hierarchy of ASON RA levels does not map to the hierarchy of OSPF areas. Instead, successive hierarchical levels of RAs MUST be represented by separate instances of the protocol. Thus, inter-level routing information exchange (as described in Section 7) involves the export and import of routing information between protocol instances. An ASON RA may therefore be identified by the combination of its OSPF instance identifier and its OSPF area identifier. With proper and careful network-wide configuration, this can be achieved using just the OSPF area identifier, and this process is RECOMMENDED in this document. These concepts are discussed in Section 7. A key ASON requirement is the support of multiple transport planes or layers. Each transport node has associated topology (links and Malis Expires December 19, 2012 [Page 6] INTERNET DRAFT RFC5787bis June 19, 2012 reachability) which is used for ASON routing. 3. Terminology and Identification This section describes the mapping of key ASON entities to OSPF entities. Appendix A contains a complete glossary of ASON routing terminology. There are three categories of identifiers used for ASON routing (G7715.1): transport plane names, control plane identifiers for components, and Signaling Communications Network (SCN) addresses. This section discusses the mapping between ASON routing identifiers and corresponding identifiers defined for GMPLS routing, and how these support the physical (or logical) separation of transport plane entities and control plane components. GMPLS supports this separation of identifiers and planes. In the context of OSPF Traffic Engineering (TE), an ASON transport node corresponds to a unique OSPF TE node. An OSPF TE node is uniquely identified by the TE Router Address TLV [RFC3630]. In this document, this TE Router Address is referred to as the TE Router ID, which is in the ASON SCN name space. The TE Router ID should not be confused with the OSPF Router ID which uniquely identifies an OSPF router within an OSPF routing domain [RFC2328] and is in a name space for control plane components. The Router Address top-level TLV definition, processing, and usage are largely unchanged from [RFC3630]. This TLV specifies a stable OSPF TE node IP address, i.e., the IP address is always reachable when there is IP connectivity to the associated OSPF TE node. However, in the context of the OSPF ASON operation, the TE Router ID is an identifier within the ASON SCN. ASON defines a Routing Controller (RC) as an entity that handles (abstract) information needed for routing and the routing information exchange with peering RCs by operating on the Routing Database (RDB). ASON defines a Protocol Controller (PC) as an entity that handles protocol-specific message exchanges according to the reference point over which the information is exchanged (e.g., E-NNI, I-NNI), and internal exchanges with the Routing Controller (RC) [RFC4258]. In this document, an OSPF router advertising ASON TE topology information will perform both the functions of the RC and PC. The OSPF routing domain comprises the control plane and each OSPF router is uniquely identified by its OSPF Router ID [RFC2328]. 4. Reachability In ASON, reachability refers to the set of endpoints reachable in the transport plane by an associated ASON transport node. Reachable entities are identified in the ASON SCN name space. Malis Expires December 19, 2012 [Page 7] INTERNET DRAFT RFC5787bis June 19, 2012 In order to advertise blocks of reachable address prefixes, a summarization mechanism is introduced that is based on the techniques described in [RFC5786]. For ASON reachability advertisement, blocks of reachable address prefixes are advertised together with the associated transport plane node. The transport plane node is identified in OSPF TE LSAs by its TE Router ID, as discussed in section 6. In order to support ASON reachability advertisement, the Node Attribute TLV defined in [RFC5786] is used to advertise the combination of a TE Router ID and its set of associated reachable address prefixes. The Node Attribute TLV can contain the following sub-TLVs: - TE Router ID sub-TLV: Length: 4; Defined in Section 6.2 - Node IPv4 Local Address sub-TLV: Length: variable; [RFC5786] - Node IPv6 Local Address sub-TLV: Length: variable; [RFC5786] A router may support multiple transport nodes as discussed in section 6, and, as a result, may be required to advertise reachability separately for each transport node. As a consequence, it MUST be possible for the router to originate more than one TE LSA containing the Node Attribute TLV when used for ASON reachability advertisement. Hence, the Node Attribute TLV [RFC5786] advertisement rules are relaxed. A Node Attribute TLV MAY appear in more than one TE LSA originated by the RC when the RC is advertising reachability information for a different transport node identified by the Local TE Router Sub-TLV (refer to section 6.1). 5. Link Attribute With the exception of local adaptation (described below), the mapping of link attributes and characteristics to OSPF TE Link TLV Sub-TLVs is unchanged [RFC4652]. OSPF TE Link TLV Sub-TLVs are described in [RFC3630] and [RFC4203]. Advertisement of this information SHOULD be supported on a per-layer basis, i.e., one TE LSA per unique switching capability and bandwidth granularity combination. 5.1. Local Adaptation Local adaptation is defined as a TE link attribute (i.e., sub-TLV) that describes the cross/inter-layer relationships. The Interface Switching Capability Descriptor (ISCD) TE Attribute [RFC4202] identifies the ability of the TE link to support cross- connection to another link within the same layer. When advertising Malis Expires December 19, 2012 [Page 8] INTERNET DRAFT RFC5787bis June 19, 2012 link adaptation, it also identifies the ability to use a locally terminated connection that belongs to one layer as a data link for another layer (adaptation capability). However, the information associated with the ability to terminate connections within that layer (referred to as the termination capability) is advertised with the adaptation capability. For instance, a link between two optical cross-connects will contain at least one ISCD attribute describing the Lambda Switching Capable (LSC) switching capability. Conversely, a link between an optical cross-connect and an IP/MPLS Label Switching Router (LSR) will contain at least two ISCD attributes, one for the description of the LSC termination capability and one for the Packet Switching Capable (PSC) adaptation capability. In OSPFv2, the Interface Switching Capability Descriptor (ISCD) is a sub-TLV (type 15) of the top-level Link TLV (type 2) [RFC4203]. The adaptation and termination capabilities are advertised using two separate ISCD sub-TLVs within the same top-level Link TLV. An interface MAY have more than one ISCD sub-TLV, [RFC4202] and [RFC4203]. Hence, the corresponding advertisements should not result in any compatibility issues. 5.2. Bandwidth Accounting GMPLS routing defines an Interface Switching Capability Descriptor (ISCD) that provides, among other things, the quantities of the maximum/minimum available bandwidth per priority for Label Switched Path (LSPs). One or more ISCD sub-TLVs can be associated with an interface, [RFC4202] and [RFC4203]. This information, combined with the Unreserved Bandwidth Link TLV sub-TLV [RFC3630], provides the basis for bandwidth accounting. In the ASON context, additional information may be included when the representation and information in the other advertised fields are not sufficient for a specific technology, e.g., SDH. The definition of technology-specific information elements is beyond the scope of this document. Some technologies will not require additional information beyond what is already defined in [RFC3630], [RFC4202], and [RFC4203]. 6. Routing Information Scope For ASON routing, the control plane component routing adjacency topology (i.e., the associated Protocol Controller (PC) connectivity) and the transport topology are not assumed to be congruent [RFC4258]. Hence, a single OSPF router (i.e., the PC) MUST be able to advertise Malis Expires December 19, 2012 [Page 9] INTERNET DRAFT RFC5787bis June 19, 2012 on behalf of multiple transport layer nodes. The OSPF routers are identified by OSPF Router ID and the transport nodes are identified by TE Router ID. The Router Address TLV [RFC3630] is used to advertise the TE Router ID associated with the advertising Routing Controller (RC). TE Router IDs for additional transport nodes are advertised through specification of the Local TE Router Identifier in the Local and Remote TE Router TE sub-TLV and the Local TE Router Identifier sub-TLV described in the sections below. These Local TE Router Identifiers are typically used as the local endpoints for TE Label Switched Paths (LSPs) terminating on the associated transport node. The use of multiple OSPF Routers to advertise TE information for the same transport node is not considered a required use case and is not discussed further in this document. 6.1. Link Advertisement (Local and Remote TE Router ID Sub-TLV) When an OSPF Router advertises on behalf of multiple transport nodes, the link end points cannot be automatically assigned to a single transport node associated with the advertising router. In this case, the local and remote transport nodes MUST be identified by TE router ID to unambiguously specify the transport topology. For this purpose, a new sub-TLV of the OSPFv2 TE LSA top-level Link TLV is introduced that defines the Local and Remote TE Router ID. The Type field of the Local and Remote TE Router ID sub-TLV is assigned the value TBDx (see Section 10). The Length field takes the value 8. The Value field of this sub-TLV contains 4 octets of the Local TE Router Identifier followed by 4 octets of the Remote TE Router Identifier. The value of the Local and Remote TE Router Identifier SHOULD NOT be set to 0. The format of the Local and Remote TE Router ID sub-TLV is: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type (TBDx) | Length (8) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Local TE Router Identifier | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Remote TE Router Identifier | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ This sub-TLV MUST be included as a sub-TLV of the top-level Link TLV Malis Expires December 19, 2012 [Page 10] INTERNET DRAFT RFC5787bis June 19, 2012 if the OSPF router is advertising on behalf of one or more transport nodes having TE Router IDs different from the TE Router ID advertised in the Router Address TLV. For consistency, this sub-TLV MUST be included when OSPF is used for the advertisement of ASON information as described herein. If it is not included in a Link TLV or a value of 0 is specified for the Local or Remote TE Router Identifier, the Link TLV will not be used for transport plane path computation. Additionally, the condition SHOULD be logged for possible action by the network operator. Note: The Link ID sub-TLV identifies the other end of the link (i.e., Router ID of the neighbor for point-to-point links) [RFC3630]. When the Local and Remote TE Router ID Sub-TLV is present, it MUST be used to identify local and remote transport node endpoints for the link and the Link-ID sub-TLV MUST be ignored. In fact, when the Local and Remote ID sub-TLV is specified, the Link-ID sub-TLV MAY be omitted. The Local and Remote ID sub-TLV, if specified, MUST only be specified once. If specified more than once, instances preceding the first will be ignored and condition SHOULD be logged for possible action by the network operator. 6.2. Reachability Advertisement (Local TE Router ID sub-TLV) When an OSPF router is advertising on behalf of multiple transport nodes, the routing protocol MUST be able to associate the advertised reachability information with the correct transport node. For this purpose, a new sub-TLV of the OSPFv2 TE LSA top-level Node Attribute TLV is introduced. This TLV associates the local prefixes (see above) to a given transport node identified by TE Router ID. The Type field of the Local TE Router ID sub-TLV is assigned the value 5 (see Section 10). The Length field takes the value 4. The Value field of this sub-TLV contains the Local TE Router Identifier [RFC3630] encoded over 4 octets. The format of the Local TE Router ID sub-TLV is: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type (5) | Length (4) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Local TE Router Identifier | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ This sub-TLV MUST be included as a sub-TLV of the top-level Node Attribute TLV if the OSPF router is advertising on behalf of one or more transport nodes having TE Router IDs different from the TE Router ID advertised in the Router Address TLV. For consistency, this sub-TLV MUST be included when OSPF is used for the advertisement of ASON information as described herein. If it is not included in a Node Attribute TLV or a value of 0 is specified for the Local TE Router Identifier, the Note Attribute TLV will not be used for determining ASON SCN reachability. Additionally, the condition SHOULD be logged for possible action by the network operator. Malis Expires December 19, 2012 [Page 11] INTERNET DRAFT RFC5787bis June 19, 2012 7. Routing Information Dissemination An ASON routing area (RA) represents a partition of the data plane, and its identifier is used within the control plane as the representation of this partition. An RA may contain smaller RAs inter-connected by links. ASON RA levels do not map directly to OSPF areas. Rather, hierarchical levels of RAs are represented by separate OSPF protocol instances. However, it is useful to align the RA identifiers and area ID in order to facilitate isolation of RAs as described in Section 11.1. Routing controllers (RCs) supporting multiple RAs disseminate information downward and upward in this ASON hierarchy. The vertical routing information dissemination mechanisms described in this section do not introduce or imply hierarchical OSPF areas. RCs supporting RAs at multiple levels are structured as separate OSPF instances with routing information exchange between levels described by import and export rules between these instances. The functionality described herein does not pertain to OSPF areas or OSPF Area Border Router (ABR) functionality. 7.1 Import/Export Rules RCs supporting RAs disseminate information upward and downward in the hierarchy by importing/exporting routing information as TE LSAs. TE LSAs are area-scoped opaque LSAs with opaque type 1 [RFC3630]. The information that MAY be exchanged between adjacent levels includes the Router Address, Link, and Node Attribute top-level TLVs. The imported/exported routing information content MAY be transformed, e.g., filtered or aggregated, as long as the resulting routing information is consistent. In particular, when more than one RC is bound to adjacent levels and both are allowed to import/export routing information, it is expected that these transformations are performed in a consistent manner. Definition of these policy-based mechanisms are outside the scope of this document. In practice, and in order to avoid scalability and processing overhead, routing information imported/exported downward/upward in the hierarchy is expected to include reachability information (see Section 4) and, upon strict policy control, link topology information. 7.2 Loop Prevention When more than one RC is bound to an adjacent level of the ASON hierarchy, and is configured to export routing information upward or downward, a specific mechanism is required to avoid looping of routing information. Looping is the re-advertisement of routing information into an RA that had previously advertised that routing Malis Expires December 19, 2012 [Page 12] INTERNET DRAFT RFC5787bis June 19, 2012 information upward or downward into an upper or lower level RA in the ASON hierarchy. For example, without loop prevention mechanisms, this could happen when the RC advertising routing information downward in the hierarchy is not the same one that advertises routing information upward in the hierarchy. 7.2.1 Inter-RA Export Upward/Downward Sub-TLVs The Inter-RA Export Sub-TLVs can be used to prevent the re- advertisement of OSPF TE routing information into an RA which previously advertised that information. The type value TBDz (see Section 10) will indicate that the associated routing information has been exported downward. The type value TBDy (see Section 10) will indicate that the associated routing information has been exported upward. While it is not required for routing information exported downward, both Sub-TLVs will include the Routing Area (RA) ID from which the routing information was exported. This RA is not necessarily the RA originating the routing information but RA from which the information was immediately exported. These additional Sub-TLVs MAY be included in TE LSAs that include any of the following top-level TLVs: - Router Address top-level TLV - Link top-level TLV - Node Attribute top-level TLV The Type field of the Inter-RA Export Upward and Inter-RA Export Downward sub-TLVs are respectively assigned the values TBDy and TBDz (see Section 10). The Length field in these Sub-TLVs takes the value 4. The Value field in these sub-TLVs contains the associated RA ID. The RA ID value must be a unique identifier for the RA within the ASON routing domain. The format of the Inter-RA Export Upward and Inter-RA Export Downward Sub-TLVs is graphically depicted below: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Upward/Downward Type | Length (4) | | (TBDy/TBDz) | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Associated RA ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Malis Expires December 19, 2012 [Page 13] INTERNET DRAFT RFC5787bis June 19, 2012 7.2.2 Inter-RA Export Upward/Downward Sub-TLV Processing TE LSAs MAY be imported or exported downward or upward in the ASON routing hierarchy. The direction and advertising RA ID are advertised in an Inter-RA Export Upward/Downward Sub-TLV. They MUST be retained and advertised in the receiving RA with the associated routing information. When exporting routing information upward in the ASON routing hierarchy, any information received from a level above, i.e., tagged with an Inter-RA Export Downward Sub-TLV, MUST NOT be exported upward. Since an RA at level N is contained by a single RA at level N+1, this is the only checking that is necessary and the associated RA ID is used solely for informational purposes. When exporting routing information downward in the ASON routing hierarchy, any information received from a level below, i.e., tagged with an Inter-RA Export Upward Sub-TLV MUST NOT be exported downward if the target RA ID matches the RA ID associated with the routing information. This additional checking is required for routing information exported downward since a single RA at level N+1 may contain multiple RAs at level N in the ASON routing hierarchy. In order words, routing information MUST NOT be exported downward into the RA from which it was received. 8. OSPFv2 Scalability The extensions described herein are only applicable to ASON routing domains and it is not expected that the attendant reachability (see Section 4) and link information will ever be combined with global Internet or Layer 3 Virtual Private Network (VPN) routing. If there were ever a requirement for a given RC to participate in both domains, separate OSPFv2 instances would be utilized. However, in a multi-level ASON hierarchy, the potential volume of information could be quite large and the recommendations in this section MUST be followed by RCs implementing this specification. - Routing information exchange upward/downward in the hierarchy between adjacent RAs MUST, by default, be limited to reachability information. In addition, several transformations such as prefix aggregation are RECOMMENDED to reduce the amount of information imported/exported by a given RC when such transformations will not impact consistency. - Routing information exchange upward/downward in the ASON hierarchy involving TE attributes MUST be under strict policy control. Pacing and min/max thresholds for triggered updates are strongly RECOMMENDED. Malis Expires December 19, 2012 [Page 14] INTERNET DRAFT RFC5787bis June 19, 2012 - The number of routing levels MUST be maintained under strict policy control. 9. Security Considerations This document specifies the contents and processing of OSPFv2 TE LSAs [RFC3630] and [RFC4202]. The TE LSA extensions defined in this document are not used for SPF computation, and have no direct effect on IP routing. Additionally, ASON routing domains are delimited by the usual administrative domain boundaries. Any mechanisms used for securing the exchange of normal OSPF LSAs can be applied equally to all TE LSAs used in the ASON context. Authentication of OSPFv2 LSA exchanges (such as OSPF cryptographic authentication [RFC2328] and [RFC5709]) can be used to secure against passive attacks and provide significant protection against active attacks. [RFC5709] defines a mechanism for authenticating OSPFv2 packets by making use of the HMAC algorithm in conjunction with the SHA family of cryptographic hash functions. If a stronger authentication were believed to be required, then the use of a full digital signature [RFC2154] would be an approach that should be seriously considered. Use of full digital signatures would enable precise authentication of the OSPF router originating each OSPF link-state advertisement, and thereby provide much stronger integrity protection for the OSPF routing domain. RCs implementing export/import of ASON routing information between RAs MUST also include policy control of both the maximum amount of information advertised between RAs and the maximum rate at which it is advertised. This is to isolate the consequences of an RC being compromised to the RAs to which that subverted RC is attached. 10. IANA Considerations This document is classified as Standards Track. It defines new sub- TLVs for inclusion in OSPF TE LSAs. According to the assignment policies for the registries of code points for these sub-TLVs, values must be assigned by IANA [RFC3630]. This draft requests early allocation of IANA code points in accordance with [RFC4020]. [NOTE TO RFC Editor: this paragraph and the RFC 4020 reference can be removed during RFC editing]. The following subsections summarize the required sub-TLVs. 10.1. Sub-TLVs of the Link TLV This document defines the following sub-TLVs of the Link TLV advertised in the OSPF TE LSA: - Local and Remote TE Router ID sub-TLV (TBDx) - Inter-RA Export Upward sub-TLV (TBDy) - Inter-RA Export Downward sub-TLV (TBDz) Malis Expires December 19, 2012 [Page 15] INTERNET DRAFT RFC5787bis June 19, 2012 Codepoints for these Sub-TLVs should be allocated from the "Types for sub-TLVs of TE Link TLV (Value 2)" registry standards action range (0 - 32767) [RFC3630]. Note that the same values for the Inter-RA Export Upward sub-TLV and the Inter-RA Export Downward Sub-TLV MUST be used when they appear in the Link TLV, Node Attribute TLV, and Router Address TLV. 10.2. Sub-TLVs of the Node Attribute TLV This document defines the following sub-TLVs of the Node Attribute TLV advertised in the OSPF TE LSA: - Local TE Router ID sub-TLV (5) - Inter-RA Export Upward sub-TLV (TDBy) - Inter-RA Export Downward sub-TLV (TBDz) Codepoints for these Sub-TLVs should be assigned from the "Types for sub-TLVs of TE Node Attribute TLV (Value 5)" registry standards action range (0 - 32767) [RFC5786]. Note that the same values for the Inter-RA Export Upward sub-TLV and the Inter-RA Export Downward Sub-TLV MUST be used when they appear in the Link TLV, Node Attribute TLV, and Router Address TLV. 10.3. Sub-TLVs of the Router Address TLV The Router Address TLV is advertised in the OSPF TE LSA [RFC3630]. Since this TLV currently has no Sub-TLVs defined, a "Types for sub- TLVs of Router Address TLV (Value 1)" registry must be defined. The registry guidelines for the assignment of types for sub-TLVs of the Router Address TLV are as follows: o Types in the range 0-32767 are to be assigned via Standards Action. o Types in the range 32768-32777 are for experimental use; these will not be registered with IANA, and MUST NOT be mentioned by RFCs. o Types in the range 32778-65535 are not to be assigned at this time. Before any assignments can be made in this range, there MUST be a Standards Track RFC that specifies IANA Considerations that covers the range being assigned. This document defines the following sub-TLVs for inclusion in the Router Address TLV: Malis Expires December 19, 2012 [Page 16] INTERNET DRAFT RFC5787bis June 19, 2012 - Inter-RA Export Upward sub-TLV (TBDy) - Inter-RA Export Downward sub-TLV (TBDz) Codepoints for these Sub-TLVs should be allocated from the "Types for sub-TLVs of Router Address TLV (Value 1)" registry standards action range (0 - 32767). Note that the same values for the Inter-RA Export Upward sub-TLV and the Inter-RA Export Downward Sub-TLV MUST be used when they appear in the Link TLV, Node Attribute TLV, and Router Address TLV. 11. Management Considerations 11.1. Routing Area (RA) Isolation If the RA Identifier is mapped to the OSPF Area ID as recommended in section 2.0, OSPF [RFC2328] implicitly provides isolation. On any intra-RA link, packets will only be accepted if the area-id in the OSPF packet header matches the area ID for the OSPF interface on which the packet was received. Hence, RCs will only establish adjacencies and exchange reachability information (see Section 4.0) with RCs in the same RC. Other mechanisms for RA isolation are beyond the scope of this document. 11.2 Routing Area (RA) Topology/Configuration Changes The GMPLS Routing for ASON requirements [RFC4258] dictate that the routing protocol MUST support reconfiguration and SHOULD support architectural evolution. OSPF [RFC2328] includes support for the dynamic introduction or removal of ASON reachability information through the flooding and purging of OSPF opaque LSAs [RFC5250]. Also, when an RA is partitioned or an RC fails, stale LSAs SHOULD NOT be used unless the advertising RC is reachable. The configuration of OSPF RAs and the policies governing the redistribution of ASON reachability information between RAs are implementation issues outside of the OSPF routing protocol and beyond the scope of this document. 12. Comparison to Requirements in RFC 4258 The following table shows how this draft complies with the requirements in [RFC4258]. The first column contains a requirements number (1-30) and the relevant section in RFC 4258. The second column describes the requirement, the third column discusses the compliance to that requirement, and the fourth column lists the relevant section in draft, and/or another RFC that already satisfies the requirement. Malis Expires December 19, 2012 [Page 17] INTERNET DRAFT RFC5787bis June 19, 2012 +----------+---------------------------+---------------+-------------+ | RFC 4258 | RFC 4258 Requirement | Compliance | Reference | | Section | | | | | (Req. | | | | | Number) | | | | +----------+---------------------------+---------------+-------------+ | 3.0 (1) | The failure of an RC, or | Implied by | Not an | | | the failure of | separation of |attribute of | | |communications between RCs,| transport and | routing | | |and the subsequent recovery|control plane. | protocol. | | |from the failure condition | | | | | MUST NOT disrupt call in | | | | | progress. | | | +----------+---------------------------+---------------+-------------+ | 3.1 (2) |Multiple Hierarchical Level| Yes | Sections 2 | | | of ASON Routing Areas | | and 3 | | | (RAs). | | | +----------+---------------------------+---------------+-------------+ | 3.1 (3) | Prior to establishing | Yes, when RA |Section 11.1 | | | communications, RCs MUST | maps to OSPF | | | |verify that they are bound | Area ID. | | | | to the same parent RA. | Otherwise, | | | | | out of scope. | | +----------+---------------------------+---------------+-------------+ | 3.1 (4) | The RC ID MUST be unique | Yes |RFC 2328 and | | | within its containing RA. | | Section 3. | +----------+---------------------------+---------------+-------------+ | 3.1 (5) |Each RA within a carrier's |Yes - although | Sections 2, | | | network SHALL be uniquely | uniqueness is | 3, and 11.1 | | |identifiable. RA IDs MAY be|the operator's | | | |associated with a transport|responsibility.| | | | plane name space, whereas | | | | |RC IDs are associated with | | | | |a control plane name space.| | | +----------+---------------------------+---------------+-------------+ | 3.2 (6) | Hierarchical Routing | Yes | Section 7 | | | Information Dissemination | | | +----------+---------------------------+---------------+-------------+ | 3.2 (7) | Routing Information | Yes | Section 7.1 | | |exchanged between levels N | | | | | and N+1 via separate | | | | | instances and | | | | | import/export. | | | +----------+---------------------------+---------------+-------------+ Malis Expires December 19, 2012 [Page 18] INTERNET DRAFT RFC5787bis June 19, 2012 +----------+---------------------------+---------------+-------------+ | 3.2 (8) | Routing Information | No - Not | | | |exchanged between levels N | described. | | | | and N+1 via external link | | | | | (inter-RA links). | | | +----------+---------------------------+---------------+-------------+ | 3.2 (9) | Routing information | Yes | Sections 4, | | | exchange MUST include | |6, 6.1, 6.2, | | | reachability information | | and 8 | | | and MAY include, upon | | | | | policy decision, node and | | | | | link topology. | | | +----------+---------------------------+---------------+-------------+ | 3.2 (10) | There SHOULD NOT be any |Yes - separate | Sections 2 | | | dependencies on the | instances. | and 3 | | |different routing protocols| | | | | used within an RA or in | | | | | different RAs. | | | +----------+---------------------------+---------------+-------------+ | 3.2 (11) |The routing protocol SHALL | Yes | Section 7.2 | | | differentiate the routing | | | | |information originated at a| | | | |given-level RA from derived| | | | | routing information | | | | | (received from external | | | | | RAs), even when this | | | | |information is forwarded by| | | | | another RC at the same | | | | | level. | | | +----------+---------------------------+---------------+-------------+ | 3.2 (12) | The routing protocol MUST | Yes | Section 7.2 | | | provide a mechanism to | | | | | prevent information | | | | |propagated from a Level N+1| | | | | RA's RC into the Level N | | | | | RA's RC from being | | | | | re-introduced into the | | | | | Level N+1 RA's RC. | | | +----------+---------------------------+---------------+-------------+ | 3.2 (13) | The routing protocol MUST | Yes | Section 7.2 | | | provide a mechanism to | | | | | prevent information | | | | |propagated from a Level N-1| | | | | RA's RC into the Level N | | | | | RA's RC from being | | | | | re-introduced into the | | | | | Level N-1 RA's RC. | | | +----------+---------------------------+---------------+-------------+ Malis Expires December 19, 2012 [Page 19] INTERNET DRAFT RFC5787bis June 19, 2012 +----------+---------------------------+---------------+-------------+ | 3.2 (14) | Instance of a Level N | Yes | Sections 2, | | | routing function and an | | 3, and 7 | | | instance of a Level N+1 | | | | | routing function in the | | | | | same system. | | | +----------+---------------------------+---------------+-------------+ | 3.2 (15) | The Level N routing | Not described | N/A | | | function is on a separate | but possible. | | | | system the Level N+1 | | | | | routing function. | | | +----------+---------------------------+---------------+-------------+ | 3.3 (16) |The RC MUST support static | The automation| Sections 2 | | | (i.e., operator assisted) | requirement is|and 3. Config| | | and MAY support automated | ambiguous. | is product | | | configuration of the | OSPF supports | specific. | | |information describing its | auto-discovery| Refer to | | |relationship to its parent | of neighbors | RFC 2328 for| | | and its child within the | and topology. | OSPF auto- | | | hierarchical structure | Default and | discovery. | | | (including RA ID and RC | automatically | | | | ID). | configured | | | | | polices are | | | | | out of scope. | | +----------+---------------------------+---------------+-------------+ | 3.3 (17) |The RC MUST support static |Yes - when OSPF|RFC 2328 and | | | (i.e., operator assisted) |area maps to RA|Section 11.1 | | | and MAY support automated | discovery is | | | | configuration of the | automatic. | | | |information describing its | | | | | associated adjacencies to | | | | | other RCs within an RA. | | | +----------+---------------------------+---------------+-------------+ | 3.3 (18) |The routing protocol SHOULD| Yes | RFC 2328 | | |support all the types of RC| | | | | adjacencies described in | | | | |Section 9 of [G.7715]. The | | | | | latter includes congruent | | | | |topology (with distributed | | | | | RC) and hubbed topology | | | | |(e.g., note that the latter| | | | | does not automatically | | | | | imply a designated RC). | | | +----------+---------------------------+---------------+-------------+ Malis Expires December 19, 2012 [Page 20] INTERNET DRAFT RFC5787bis June 19, 2012 +----------+---------------------------+---------------+-------------+ | 3.4 (19) |The routing protocol SHOULD| Yes |RFC 2328, RFC| | | be capable of supporting | | 5250, and | | |architectural evolution in | |Section 11.2.| | | terms of the number of | | | | |hierarchical levels of RAs,| | | | |as well as the aggregation | | | | | and segmentation of RAs. | | | +----------+---------------------------+---------------+-------------+ |3.5.2 (20)|Advertisements MAY contain | | | | |the following common set of| | | | | information regardless of | | | | | whether they are link or | | | | | node related: | | | | | - RA ID of the RA to | Yes |Section 7.2.1| | |which the advertisement is | | | | | bounded | | | | | - RC ID of the entity | Yes | RFC 2328 | | | generating the | | | | | advertisement | | | | | - Information to | Yes |RFC 2328, RFC| | | uniquely identify | | 5250 | | | advertisements | | | | | - Information to | No - Must | | | | determine whether an |compare to old | | | | advertisement has been | | | | | updated | | | | | - Information to | Yes |Section 7.2.1| | | indicate when an | | | | | advertisement has been | | | | | derived from a different | | | | | level RA | | | +----------+---------------------------+---------------+-------------+ |3.5.3 (21)|The Node Attributes Node ID|Yes - Prefixes | RFC 5786, | | | and Reachability must be | only for |Section 4 and| | | advertised. It MAY be | reachability | 6 | | | advertised as a set of | | | | |associated external (e.g., | | | | | User Network Interface | | | | | (UNI)) address/address | | | | | prefixes or a set of | | | | | associated SNPP link | | | | | IDs/SNPP ID prefixes, the | | | | |selection of which MUST be | | | | | consistent within the | | | | | applicable scope. | | | +----------+---------------------------+---------------+-------------+ Malis Expires December 19, 2012 [Page 21] INTERNET DRAFT RFC5787bis June 19, 2012 +----------+---------------------------+---------------+-------------+ |3.5.4 (22)| The Link Attributes Local | Yes | Section 6.1 | | | SNPP link ID, Remote SNPP | | | | |link ID, and layer specific| | | | | characteristics must be | | | | | advertised. | | | +----------+---------------------------+---------------+-------------+ |3.5.4 (23)| Link Signaling Attributes | Yes | Section 5, | | |other than Local Adaptation| | RFC 4652 - | | |(Signal Type, Link Weight, | |Section 5.3.1| | | Resource Class, Local | | | | | Connection Types, Link | | | | | Capacity, Link | | | | | Availability, Diversity | | | | | Support) | | | +----------+---------------------------+---------------+-------------+ |3.5.4 (24)| Link Signaling Local | Yes | Section 5.1 | | | Adaptation | | | +----------+---------------------------+---------------+-------------+ | 5 (25) | The routing adjacency | Yes |Section 2, 3,| | | topology (i.e., the | | and 6 | | |associated PC connectivity | | | | |topology) and the transport| | | | |network topology SHALL NOT | | | | |be assumed to be congruent.| | | +----------+---------------------------+---------------+-------------+ | 5 (26) |The routing topology SHALL | Yes |RFC 2328, RFC| | | support multiple links | | 3630 | | | between nodes and RAs. | | | +----------+---------------------------+---------------+-------------+ | 5 (27) |The routing protocol SHALL | Yes |RFC 2328, RFC| | | converge such that the | | 5250 | | | distributed RDBs become | | | | |synchronized after a period| | | | | of time. | | | +----------+---------------------------+---------------+-------------+ | 5 (28) |Self-consistent information|Yes - However, | Section 7.1 | | | at the receiving level | this is not a | | | | resulting from any | routing | | | | transformation (filter, | protocol | | | | summarize, etc.) and | function. | | | | forwarding of information | | | | | from one RC to RC(s) at | | | | | different levels when | | | | |multiple RCs are bound to a| | | | | single RA. | | | +----------+---------------------------+---------------+-------------+ Malis Expires December 19, 2012 [Page 22] INTERNET DRAFT RFC5787bis June 19, 2012 +----------+---------------------------+---------------+-------------+ | 5 (29) | In order to support |Partial - OSPF |RFC 2328 and | | | operator-assisted changes | supports the | RFC 5250 | | | in the containment | purging of | | | | relationships of RAs, the | stale | | | | routing protocol SHALL |advertisements | | | |support evolution in terms |and origination| | | | of the number of | of new. The | | | |hierarchical levels of RAs.|non-disruptive | | | | For example: support of | behavior is | | | | non-disruptive operations |implementation | | | |such as adding and removing| specific. | | | | RAs at the top/bottom of | | | | | the hierarchy, adding or | | | | | removing a hierarchical | | | | |level of RAs in or from the| | | | |middle of the hierarchy, as| | | | | well as aggregation and | | | | | segmentation of RAs. | | | +----------+---------------------------+---------------+-------------+ | 5 (30) | A collection of links and |Yes - Within an| Sections 4 | | |nodes such as a subnetwork | RA it must be | and 6 | | | or RA MUST be able to | consistent. | | | | represent itself to the | | | | | wider network as a single | | | | | logical entity with only | | | | |its external links visible | | | | | to the topology database. | | | +----------+---------------------------+---------------+-------------+ 13. References 13.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2328] Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998. [RFC3630] Katz, D., Kompella, K., and D. Yeung, "Traffic Engineering (TE) Extensions to OSPF Version 2", RFC 3630, September 2003. [RFC3945] Mannie, E., Ed., "Generalized Multi-Protocol Label Switching (GMPLS) Architecture", RFC 3945, October 2004. [RFC4202] Kompella, K., Ed., and Y. Rekhter, Ed., "Routing Extensions in Support of Generalized Multi-Protocol Malis Expires December 19, 2012 [Page 23] INTERNET DRAFT RFC5787bis June 19, 2012 Label Switching (GMPLS)", RFC 4202, October 2005. [RFC4203] Kompella, K., Ed., and Y. Rekhter, Ed., "OSPF Extensions in Support of Generalized Multi-Protocol Label Switching (GMPLS)", RFC 4203, October 2005. [RFC5250] Berger, L., Bryskin, I., Zinin, A., and R. Coltun, "The OSPF Opaque LSA Option", RFC 5250, July 2008. [RFC5786] Aggarwal, R. and K. Kompella, "Advertising a Router's Local Addresses in OSPF TE Extensions", RFC 5786, March 2010. 13.2. Informative References [RFC2154] Murphy, S., Badger, M., and B. Wellington, "OSPF with Digital Signatures", RFC 2154, June 1997. [RFC4020] Kompella, K. and A. Zinin, "Early IANA Allocation of Standards Track Code Points", BCP 100, RFC 4020, February 2005. [RFC4258] Brungard, D., Ed., "Requirements for Generalized Multi- Protocol Label Switching (GMPLS) Routing for the Automatically Switched Optical Network (ASON)", RFC 4258, November 2005. [RFC4652] Papadimitriou, D., Ed., Ong, L., Sadler, J., Shew, S., and D. Ward, "Evaluation of Existing Routing Protocols against Automatic Switched Optical Network (ASON) Routing Requirements", RFC 4652, October 2006. [RFC5709] Bhatia, M., Manral, V., Fanto, M., White, R., Barnes, M., Li, T., and R. Atkinson, "OSPFv2 HMAC-SHA Cryptographic Authentication", RFC 5709, October 2009. For information on the availability of ITU Documents, please see http://www.itu.int. [G.7715] ITU-T Rec. G.7715/Y.1306, "Architecture and Requirements for the Automatically Switched Optical Network (ASON)", June 2002. [G.7715.1] ITU-T Rec. G.7715.1/Y.1706.1, "ASON Routing Architecture and Requirements for Link State Protocols", February 2004. Malis Expires December 19, 2012 [Page 24] INTERNET DRAFT RFC5787bis June 19, 2012 [G.805] ITU-T Rec. G.805, "Generic Functional Architecture of Transport Networks)", March 2000. [G.8080] ITU-T Rec. G.8080/Y.1304, "Architecture for the Automatically Switched Optical Network (ASON)," June 2006 (and Amendments 1 (March 2008) and 2 (Sept. 2010)). 14. Acknowledgements The editors would like to thank Lyndon Ong, Remi Theillaud, Stephen Shew, Jonathan Sadler, Deborah Brungard, Lou Berger, and Adrian Farrel for their useful comments and suggestions. 14.1 RFC 5787 Acknowledgements The author would like to thank Dean Cheng, Acee Lindem, Pandian Vijay, Alan Davey, Adrian Farrel, Deborah Brungard, and Ben Campbell for their useful comments and suggestions. Lisa Dusseault and Jari Arkko provided useful comments during IESG review. Question 14 of Study Group 15 of the ITU-T provided useful and constructive input. Malis Expires December 19, 2012 [Page 25] INTERNET DRAFT RFC5787bis June 19, 2012 Appendix A. ASON Terminology This document makes use of the following terms: Administrative domain: (See Recommendation [G.805].) For the purposes of [G7715.1], an administrative domain represents the extent of resources that belong to a single player such as a network operator, a service provider, or an end-user. Administrative domains of different players do not overlap amongst themselves. Control plane: performs the call control and connection control functions. Through signaling, the control plane sets up and releases connections, and may restore a connection in case of a failure. (Control) Domain: represents a collection of (control) entities that are grouped for a particular purpose. The control plane is subdivided into domains matching administrative domains. Within an administrative domain, further subdivisions of the control plane are recursively applied. A routing control domain is an abstract entity that hides the details of the RC distribution. External NNI (E-NNI): interfaces located between protocol controllers between control domains. Internal NNI (I-NNI): interfaces located between protocol controllers within control domains. Link: (See Recommendation G.805.) A "topological component" that describes a fixed relationship between a "subnetwork" or "access group" and another "subnetwork" or "access group". Links are not limited to being provided by a single server trail. Management plane: performs management functions for the transport plane, the control plane, and the system as a whole. It also provides coordination between all the planes. The following management functional areas are performed in the management plane: performance, fault, configuration, accounting, and security management. Management domain: (See Recommendation G.805.) A management domain defines a collection of managed objects that are grouped to meet organizational requirements according to geography, technology, policy, or other structure, and for a number of functional areas such as configuration, security, (FCAPS), for the purpose of providing control in a consistent manner. Management domains can be disjoint, contained, or overlapping. As such, the resources Malis Expires December 19, 2012 [Page 26] INTERNET DRAFT RFC5787bis June 19, 2012 within an administrative domain can be distributed into several possible overlapping management domains. The same resource can therefore belong to several management domains simultaneously, but a management domain shall not cross the border of an administrative domain. Subnetwork Point (SNP): The SNP is a control plane abstraction that represents an actual or potential transport plane resource. SNPs (in different subnetwork partitions) may represent the same transport resource. A one-to-one correspondence should not be assumed. Subnetwork Point Pool (SNPP): A set of SNPs that are grouped together for the purposes of routing. Termination Connection Point (TCP): A TCP represents the output of a Trail Termination function or the input to a Trail Termination Sink function. Transport plane: provides bidirectional or unidirectional transfer of user information, from one location to another. It can also provide transfer of some control and network management information. The transport plane is layered; it is equivalent to the Transport Network defined in Recommendation G.805. User Network Interface (UNI): interfaces are located between protocol controllers between a user and a control domain. Note: There is no routing function associated with a UNI reference point. Appendix B. ASON Routing Terminology This document makes use of the following terms: Routing Area (RA): an RA represents a partition of the data plane, and its identifier is used within the control plane as the representation of this partition. Per [G.8080], an RA is defined by a set of sub-networks, the links that interconnect them, and the interfaces representing the ends of the links exiting that RA. An RA may contain smaller RAs inter-connected by links. The limit of subdivision results in an RA that contains two sub- networks interconnected by a single link. Routing Database (RDB): a repository for the local topology, network topology, reachability, and other routing information that is updated as part of the routing information exchange and may additionally contain information that is configured. The RDB may contain routing information for more than one routing area (RA). Malis Expires December 19, 2012 [Page 27] INTERNET DRAFT RFC5787bis June 19, 2012 Routing Components: ASON routing architecture functions. These functions can be classified as protocol independent (Link Resource Manager or LRM, Routing Controller or RC) or protocol specific (Protocol Controller or PC). Routing Controller (RC): handles (abstract) information needed for routing and the routing information exchange with peering RCs by operating on the RDB. The RC has access to a view of the RDB. The RC is protocol independent. Note: Since the RDB may contain routing information pertaining to multiple RAs (and possibly to multiple layer networks), the RCs accessing the RDB may share the routing information. Link Resource Manager (LRM): supplies all the relevant component and TE link information to the RC. It informs the RC about any state changes of the link resources it controls. Protocol Controller (PC): handles protocol-specific message exchanges according to the reference point over which the information is exchanged (e.g., E-NNI, I-NNI), and internal exchanges with the RC. The PC function is protocol dependent. Authors' Addresses Andrew G. Malis Verizon Communications 117 West St. Waltham MA 02451 USA EMail: andrew.g.malis@verizon.com Acee Lindem Ericsson 102 Carric Bend Court Cary, NC 27519 EMail: acee.lindem@ericsson.com Dimitri Papadimitriou Alcatel-Lucent Copernicuslaan, 50 2018 Antwerpen, Belgium EMail: dimitri.papadimitriou@alcatel-lucent.com Malis Expires December 19, 2012 [Page 28] INTERNET DRAFT RFC5787bis June 19, 2012 Malis Expires December 19, 2012 [Page 29]