Global Routing Operations T. Evens Internet-Draft S. Bayraktar Updates: 7854 (if approved) Cisco Systems Intended status: Standards Track P. Lucente Expires: December 18, 2017 NTT Communications P. Mi Tencent S. Zhuang Huawei June 16, 2017 Support for Adj-RIB-Out in BGP Monitoring Protocol (BMP) draft-ietf-grow-bmp-adj-rib-out-00 Abstract The BGP Monitoring Protocol (BMP) defines access to only the Adj-RIB- In Routing Information Bases (RIBs). This document updates the BGP Monitoring Protocol (BMP) RFC 7854 by adding access to the Adj-RIB- Out RIBs. It adds a new flag to the peer header to distinguish Adj- RIB-In and Adj-RIB-Out. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on December 18, 2017. Copyright Notice Copyright (c) 2017 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of Evens, et al. Expires December 18, 2017 [Page 1] Internet-Draft BMP Adj-RIB-Out June 2017 publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 3 4. Per-Peer Header . . . . . . . . . . . . . . . . . . . . . . . 3 5. Adj-RIB-Out . . . . . . . . . . . . . . . . . . . . . . . . . 4 5.1. Post-Policy . . . . . . . . . . . . . . . . . . . . . . . 4 5.2. Pre-Policy . . . . . . . . . . . . . . . . . . . . . . . 4 6. BMP Messages . . . . . . . . . . . . . . . . . . . . . . . . 4 6.1. Route Monitoring and Route Mirroring . . . . . . . . . . 4 6.2. Statistics Report . . . . . . . . . . . . . . . . . . . . 4 6.3. Peer Down and Up Notifications . . . . . . . . . . . . . 5 7. Security Considerations . . . . . . . . . . . . . . . . . . . 5 8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 5 8.1. BMP Peer Flags . . . . . . . . . . . . . . . . . . . . . 5 8.2. BMP Statistics Types . . . . . . . . . . . . . . . . . . 6 9. References . . . . . . . . . . . . . . . . . . . . . . . . . 6 9.1. Normative References . . . . . . . . . . . . . . . . . . 6 9.2. URIs . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . 7 Contributors . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 7 1. Introduction BGP Monitoring Protocol (BMP) defines monitoring of the received (e.g. Adj-RIB-In) Routing Information Bases (RIBs) per peer. The Adj-RIB-In pre-policy conveys to a BMP receiver all RIB data before any policy has been applied. The Adj-RIB-In post-policy conveys to a BMP receiver all RIB data after policy filters and/or modifications have been applied. An example of pre-policy verses post-policy is when an inbound policy applies attribute modification or filters. Pre-policy would contain information prior to the inbound policy changes or filters of data. Post policy would convey the changed data or would not contain the filtered data. Monitoring the received updates that the router received before any policy has been applied is the primary level of monitoring for most use-cases. Inbound policy validation and auditing is the primary use-case for enabling post-policy monitoring. Evens, et al. Expires December 18, 2017 [Page 2] Internet-Draft BMP Adj-RIB-Out June 2017 In order for a BMP receiver to receive any BGP data, the BMP sender (e.g. router) needs to have an established BGP peering session and actively be receiving updates for an Adj-RIB-In. Being able to only monitor the Adj-RIB-In puts a restriction on what data is available to BMP receivers via BMP senders (e.g. routers). This is an issue when the receiving end of the BGP peer is not enabled for BMP or when it is not accessible for administrative reasons. For example, a service provider advertises prefixes to a customer, but the service provider cannot see what it advertises via BMP. Asking the customer to enable BMP and monitoring of the Adj- RIB- In is not feasible. This document updates BGP Monitoring Protocol (BMP) RFC 7854 [RFC7854] peer header by adding a new flag to distinguish Adj-RIB-In verses Adj-RIB-Out. Adding Adj-RIB-Out enables the ability for a BMP sender to send to a BMP receiver what it advertises to BGP peers, which can be used for outbound policy validation and to monitor RIBs that were advertised. 2. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. 3. Definitions o Adj-RIB-Out: As defined in [RFC4271], "The Adj-RIBs-Out contains the routes for advertisement to specific peers by means of the local speaker's UPDATE messages." o Pre-Policy Adj-RIB-Out: The result before applying the outbound policy to an Adj-RIB-Out. This normally would match what is in the local RIB. o Post-Policy Adj-RIB-Out: The result of applying outbound policy to an Adj-RIB-Out. This MUST be what is actually sent to the peer. 4. Per-Peer Header The per-peer header has the same structure and flags as defined in section 4.2 [RFC7854] with the following O flag addition: Evens, et al. Expires December 18, 2017 [Page 3] Internet-Draft BMP Adj-RIB-Out June 2017 0 1 2 3 4 5 6 7 +-+-+-+-+-+-+-+-+ |V|L|A|O| Resv | +-+-+-+-+-+-+-+-+ o The O flag indicates Adj-RIB-In if set to 0 and Adj-RIB-Out if set to 1. The existing flags are defined in section 4.2 [RFC7854] and the remaining bits are reserved for future use. They SHOULD be transmitted as 0 and their values MUST be ignored on receipt. 5. Adj-RIB-Out 5.1. Post-Policy The primary use-case in monitoring Adj-RIB-Out is to monitor the updates transmitted to the BGP peer after outbound policy has been applied. These updates reflect the result after modifications and filters have been applied (e.g. Adj-RIB-Out Post-Policy). The L flag MUST be set to 1 in this case to indicate post-policy. 5.2. Pre-Policy As with Adj-RIB-In policy validation, there are use-cases that pre- policy Adj-RIB-Out is used to validate and audit outbound policies. For example, a comparison between pre-policy and post-policy can be used to validate the outbound policy. The L flag MUST be set to 0 in this case to indicate pre-policy. 6. BMP Messages Many BMP messages have a per-peer header but some are not applicable to Adj-RIB-In or Adj-RIB-Out monitoring. Unless otherwise defined, the O flag should be set to 0 in the per-peer header in BMP messages. 6.1. Route Monitoring and Route Mirroring The O flag MUST be set accordingly to indicate if the route monitor or route mirroring message conveys Adj-RIB-In or Adj-RIB-Out. 6.2. Statistics Report Statistics report message has Stat Type field to indicate the statistic carried in the Stat Data field. Statistics report messages are not specific to Adj-RIB-In or Adj-RIB-Out and MUST have the O flag set to zero. The O flag SHOULD be ignored by the BMP receiver. Evens, et al. Expires December 18, 2017 [Page 4] Internet-Draft BMP Adj-RIB-Out June 2017 The following new statistic types are added: o Stat Type = TBD: (64-bit Gauge) Number of routes in Adj-RIBs-Out Pre-Policy. o Stat Type = TBD: (64-bit Gauge) Number of routes in Adj-RIBs-Out Post-Policy. o Stat Type = TBD: Number of routes in per-AFI/SAFI Adj-RIB-Out Pre- Policy. The value is structured as: 2-byte Address Family Identifier (AFI), 1-byte Subsequent Address Family Identifier (SAFI), followed by a 64-bit Gauge. o Stat Type = TBD: Number of routes in per-AFI/SAFI Adj-RIB-Out Post-Policy. The value is structured as: 2-byte Address Family Identifier (AFI), 1-byte Subsequent Address Family Identifier (SAFI), followed by a 64-bit Gauge. 6.3. Peer Down and Up Notifications PEER UP and DOWN notifications convey BGP peering session state to BMP receivers. The state is independent of whether or not route monitoring or route mirroring messages will be sent for Adj-RIB-In, Adj-RIB-Out, or both. BMP receiver implementations SHOULD ignore the O flag in PEER UP and DOWN notifications. BMP receiver implementations MUST use the per-peer header O flag in route monitoring and mirroring messages in order to identify if the message is for Adj-RIB-In or Adj-RIB-Out. 7. Security Considerations It is not believed that this document adds any additional security considerations. 8. IANA Considerations This document requests that IANA assign the following new parameters to the BMP parameters name space [1]. 8.1. BMP Peer Flags This document defines the following new per-peer header flags (Section 4): o Flag 3 as O flag: The O flag indicates Adj-RIB-In if set to 0 and Adj-RIB-Out if set to 1. Evens, et al. Expires December 18, 2017 [Page 5] Internet-Draft BMP Adj-RIB-Out June 2017 8.2. BMP Statistics Types This document defines four new statistic types for statistics reporting (Section 6.2): o Stat Type = TBD: (64-bit Gauge) Number of routes in Adj-RIBs-Out Pre-Policy. o Stat Type = TBD: (64-bit Gauge) Number of routes in Adj-RIBs-Out Post-Policy. o Stat Type = TBD: Number of routes in per-AFI/SAFI Adj-RIB-Out Pre- Policy. The value is structured as: 2-byte Address Family Identifier (AFI), 1-byte Subsequent Address Family Identifier (SAFI), followed by a 64-bit Gauge. o Stat Type = TBD: Number of routes in per-AFI/SAFI Adj-RIB-Out Post-Policy. The value is structured as: 2-byte Address Family Identifier (AFI), 1-byte Subsequent Address Family Identifier (SAFI), followed by a 64-bit Gauge. 9. References 9.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC4271] Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A Border Gateway Protocol 4 (BGP-4)", RFC 4271, DOI 10.17487/RFC4271, January 2006, . [RFC7854] Scudder, J., Ed., Fernando, R., and S. Stuart, "BGP Monitoring Protocol (BMP)", RFC 7854, DOI 10.17487/RFC7854, June 2016, . 9.2. URIs [1] https://www.iana.org/assignments/bmp-parameters/bmp- parameters.xhtml Evens, et al. Expires December 18, 2017 [Page 6] Internet-Draft BMP Adj-RIB-Out June 2017 Acknowledgements The authors would like to thank John Scudder for his valuable input. Contributors Manish Bhardwaj Cisco Systems 3700 Cisco Way San Jose, CA 95134 USA Email: manbhard@cisco.com Xianyuzheng Tencent Tencent Building, Kejizhongyi Avenue, Hi-techPark, Nanshan District,Shenzhen 518057, P.R.China Weiguo Tencent Tencent Building, Kejizhongyi Avenue, Hi-techPark, Nanshan District,Shenzhen 518057, P.R.China Shugang cheng H3C Authors' Addresses Tim Evens Cisco Systems 2901 Third Avenue, Suite 600 Seattle, WA 98121 USA Email: tievens@cisco.com Evens, et al. Expires December 18, 2017 [Page 7] Internet-Draft BMP Adj-RIB-Out June 2017 Serpil Bayraktar Cisco Systems 3700 Cisco Way San Jose, CA 95134 USA Email: serpil@cisco.com Paolo Lucente NTT Communications Siriusdreef 70-72 Hoofddorp, WT 2132 NL Email: paolo@ntt.net Penghui Mi Tencent Tengyun Building,Tower A ,No. 397 Tianlin Road Shanghai 200233 China Email: kevinmi@tencent.com Shunwan Zhuang Huawei Huawei Bld., No.156 Beiqing Rd. Beijing 100095 China Email: zhuangshunwan@huawei.com Evens, et al. Expires December 18, 2017 [Page 8]