HIP Working Group M. Komu Internet-Draft HIIT Intended status: Experimental T. Henderson Expires: August 28, 2008 The Boeing Company P. Matthews Avaya H. Tschofenig Nokia Siemens Networks A. Keraenen J. Melen Ericsson Research Nomadiclab M. Bagnulo Huawei Lab at UC3M February 25, 2008 Basic HIP Extensions for Traversal of Network Address Translators and Firewalls draft-ietf-hip-nat-traversal-03.txt Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on August 28, 2008. Copyright Notice Copyright (C) The IETF Trust (2008). Komu, et al. Expires August 28, 2008 [Page 1] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 Abstract The Host Identity Protocol (HIP) provides a new namespace that can be used for uniquely identifying hosts. Existing HIP experimental specifications do not specify protocol operations across Network Address Translators (NATs). This document specifies NAT traversal extensions for HIP. The HIP shim layer is located between the network and transport layer, the extensions can also provide a more general-purpose NAT traversal support for higher-layer networking applications. The extensions are based on the use of the The Interactive Connectivity Establishment (ICE) methodology to discover a working path between two end-hosts. Using the specified extensions, two HIP-capable hosts are able to communicate with each other even when both nodes are behind NATs or firewalls. Komu, et al. Expires August 28, 2008 [Page 2] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. Protocol Description . . . . . . . . . . . . . . . . . . . . . 7 3.1. Relay Registration and NAT Detection . . . . . . . . . . . 7 3.2. Base Exchange via HIP Relay . . . . . . . . . . . . . . . 9 4. Connectivity Tests . . . . . . . . . . . . . . . . . . . . . . 11 4.1. NAT Transformation Negotiation . . . . . . . . . . . . . . 11 4.2. ICE Procedure . . . . . . . . . . . . . . . . . . . . . . 12 4.3. NAT Keep-alives . . . . . . . . . . . . . . . . . . . . . 12 5. Packet Formats . . . . . . . . . . . . . . . . . . . . . . . . 13 5.1. HIP Control Packets . . . . . . . . . . . . . . . . . . . 13 5.2. Keep-Alives . . . . . . . . . . . . . . . . . . . . . . . 13 5.3. Relay and Registration Parameters . . . . . . . . . . . . 14 5.4. LOCATOR Parameter . . . . . . . . . . . . . . . . . . . . 14 5.5. RELAY_HMAC . . . . . . . . . . . . . . . . . . . . . . . . 16 5.6. Registration Types . . . . . . . . . . . . . . . . . . . . 16 5.7. HIP ESP Data Packet Formats . . . . . . . . . . . . . . . 17 6. Security Considerations . . . . . . . . . . . . . . . . . . . 17 6.1. Privacy Considerations . . . . . . . . . . . . . . . . . . 17 6.2. Opportunistic Mode . . . . . . . . . . . . . . . . . . . . 18 7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 18 8. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 18 9. Acknowlegements . . . . . . . . . . . . . . . . . . . . . . . 18 10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 19 10.1. Normative References . . . . . . . . . . . . . . . . . . . 19 10.2. Informative References . . . . . . . . . . . . . . . . . . 20 Appendix A. Firewall Traversal . . . . . . . . . . . . . . . . . 21 Appendix B. Base Exchange without ICE Connectivity Checks . . . . 22 Appendix C. IPv4-IPv6 Interoperability . . . . . . . . . . . . . 22 Appendix D. Base Exchange through a Rendezvous Server . . . . . . 22 Appendix E. Document Revision History . . . . . . . . . . . . . . 23 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 23 Intellectual Property and Copyright Statements . . . . . . . . . . 26 Komu, et al. Expires August 28, 2008 [Page 3] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 1. Introduction HIP [I-D.ietf-hip-base] is defined as a protocol that runs directly over IPv4 or IPv6. This approach is known to have problems traversing NATs. Several different types of NATs exist, see [RFC2663]. This document describes HIP extensions for the traversal of both Network Address Translator (NAT) and Network Address and Port Translator (NAPT) middleboxes. Additionally, it covers firewalls to a certain extend (see Appendix A for a more detailed discussion). The document generally uses the term NAT to refer to these types of middleboxes. A detailed description of HIP problems with traversing legacy middleboxes is documented in [I-D.irtf-hiprg-nat]. NAT devices do not operate consistently even though a recommended behavior is described in [RFC4787]. The HIP protocol extensions in this document make as few assumptions as possible about the behavior of the NAT devices so that NAT traversal will work even with legacy NAT devices. The purpose of these extensions is to allow two HIP- enabled hosts to communicate with each other even if one or both communicating hosts are in private address realms. With some legacy NAT devices, utilizing the shortest path between two end hosts located behind NATs is not possible without relaying the traffic through a relay, such as a TURN server [I-D.ietf-behave-p2p-state]. As a consequence, the TURN server increases the roundtrip delay and may become a point of network congestion. With the extensions described in this document, hosts try to avoid the use of such a relay when possible. A distinction must be made between a HIP rendezvous server (defined in [I-D.ietf-hip-rvs]) and a HIP Relay, defined herein. HIP rendezvous servers solve initial contact and mobility related problems in networks without NATs. HIP Relay solve the same problems, in addition to NAT traversal problems. HIP Relay servers can be used both in NATted and non-NATted networks. Both rendezvous and relay services forward HIP control packets, but the main difference is that the rendezvous service forwards only the initial I1 packet of the base exchange while all other HIP control packets are sent directly between the communicating hosts. In contrast, the relay service relays all HIP control packets because p2p-unfriendly NAT devices drop the packets otherwise [I-D.ietf-behave-p2p-state]. The peers use the control channel to communicate their current locators to each other to find a direct path for carrying ESP encapsulated data traffic. A direct path between the hosts enables efficient delivery of data traffic without relaying of ESP packets through an intermediary TURN server. The direct path is searched using connectivity tests. Komu, et al. Expires August 28, 2008 [Page 4] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 The basis for the connectivity tests is ICE [I-D.ietf-mmusic-ice]. [I-D.ietf-mmusic-ice] describes ICE as follows: "The Interactive Connectivity Establishment (ICE) methodology is a technique for NAT traversal for UDP-based media streams (though ICE can be extended to handle other transport protocols, such as TCP) established by the offer/answer model. ICE is an extension to the offer/answer model, and works by including a multiplicity of IP addresses and ports in SDP offers and answers, which are then tested for connectivity by peer-to-peer connectivity checks. The IP addresses and ports included in the SDP and the connectivity checks are performed using the revised STUN specification [I-D.ietf-behave-rfc3489bis], now renamed to Session Traversal Utilities for NAT." ICE for SIP is specified in [I-D.ietf-mmusic-ice] and ICE for non-SIP protocols is specified in [I-D.rosenberg-mmusic-ice-nonsip]. Two hosts communicate their peer address set (typically consisting of IP address and port number pairs) to each other in the HIP base exchange. They are then paired with the locally operational address of the other end point and prioritized according to some policy. These address sets are then tested sequentially based on the procedure specified in ICE. Both sides participate in the connectivity tests. The tests also determine whether operational address pairs and select the preferred address pair to be used for subsequent communication. As a summary, the extensions in this document o illustrate how to encapsulate HIP packets in UDP o refer to the UDP encapsulation of IPsec ESP packets defined in Section 2.1 of RFC 3948 [RFC3948] o define how a node interacts with a HIP rendezvous server (defined in [I-D.ietf-hip-rvs]) when middleboxes are present o describe a methodology to determine operational address pairs between two end hosts based on ICE. 2. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. Komu, et al. Expires August 28, 2008 [Page 5] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 This document borrows terminology from [I-D.ietf-hip-base], [I-D.ietf-hip-mm], [RFC4423], [I-D.ietf-mmusic-ice], and [I-D.ietf-behave-rfc3489bis]. Additionally, the following terms are used: Rendezvous server: A host that forwards I1 packets to the Responder HIP Relay: A host that forwards all HIP control packets between an Initiator and Responder TURN server: A server that forwards data traffic between two end-hosts Locator: A name that controls how the packet is routed through the network and demultiplexed by the end host. It may include a concatenation of traditional network addresses such as an IPv6 address and end- to-end identifiers such as an ESP SPI. It may also include transport port numbers or IPv6 Flow Labels as demultiplexing context, or it may simply be a network address. [I-D.ietf-hip-mm] "Address" is used in this document as a synonym for locator. Transport address: Transport layer port and the corresponding IPv4/v6 address Candidate: A transport address that has not been verified yet for reachability using ICE Host candidate: An IPv4 or IPv6 address of a network interface of a host Komu, et al. Expires August 28, 2008 [Page 6] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 Server reflexive transport candidate: A translated transport address of a host as observed by a HIP Relay or a STUN server Peer reflexive transport candidate: A translated transport address of a host as observed by its peer Relayed transport candidate: A transport address that exists on a TURN server. If a permission exists, packets that arrive at this address are relayed towards the TURN client. 3. Protocol Description This section describes the normative behavior of the protocol extension. Examples of packet exchanges are provided for illustration purposes. 3.1. Relay Registration and NAT Detection HIP rendezvous servers are used in non-NATted environments and their use is described in [I-D.ietf-hip-rvs]. This section specifies a new role for these rendezvous servers to act as HIP Relays. HIP Relays forward HIP control packets between the Initiator and the Responder. TURN servers [I-D.ietf-behave-turn] are used for relaying ESP traffic. A host SHOULD register to a TURN server before registering to a HIP Relay to guarantee that the host can accept ESP traffic immediately after HIP Relay registration. A HIP relay forwards UDP-encapsulated HIP traffic, and in future extensions, a relay may also forward TCP-encapsulated traffic. The HIP Relay forwards HIP control packets. NAT traversal for HIP between two end-hosts may require the use of relays in certain scenarios. A successful NAT traversal therefore requires at least the Responder located behind a NAT to register with a HIP Relay. A HIP Relay MUST silently drop packets to a HIP Relay Client that has not previously registered with the HIP Relay. The registration process follows the generic registration extensions defined in [I-D.ietf-hip-registration] and is illustrated in Figure 1. Komu, et al. Expires August 28, 2008 [Page 7] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 HIP HIP Relay Relay Client Server | 1. UDP(I1) | +------------------------------------------------------->| | | | 2. UDP(R1(REG_INFO(RELAY_UDP_HIP))) | |<-------------------------------------------------------+ | | | 3. UDP(I2(REG_REQ(RELAY_UDP_HIP))) | +------------------------------------------------------->| | | | 4. UDP(R2(REG_RES(RELAY_UDP_HIP), REG_FROM)) | |<-------------------------------------------------------+ Figure 1: Example Registration to a HIP Relay In step 1, the Initiator starts the registration procedure by sending an I1 packet over UDP. It is RECOMMENDED that the Initiator selects a random port number from the ephemeral port range 49152-65535 for initiating a base exchange. However, the allocated port MUST be maintained until all of the corresponding HIP Associations are closed. Alternatively, a host MAY also use a single fixed port for initiating all outgoing connections. In step 2, the Responder lists the services that it supports in the R1 packet. The support for HIP-over-UDP relaying is denoted by the RELAY_UDP_HIP value. The R1 does not contain any NAT transform parameter (see Section 4.1) as discussed in Appendix B. In step 3, the Initiator selects the services it registers for and lists them in the REG_REQ parameter. In this example, the Initiator registers for HIP Relay service. In step 4, the Responder concludes the registration procedure with an R2 packet and acknowledges the registered services in the REG_RES parameter. The Responder may also denote unsuccessful registrations in the REG_FAILED parameter in R2. The Responder also includes a REG_FROM parameter that contains the transport address of the client as observed by the Relay (Server Reflexive candidate). After the registration, the Initiator needs to send periodically NAT keep- alives. There are different ways for an Initiator to learn it's publically visible IP address and port that are referred to as the "server reflexive transport candidate" in this document. This document makes use of two ways: Komu, et al. Expires August 28, 2008 [Page 8] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 o The Relay client may use STUN servers to detect the server reflexive locator, as described in [I-D.ietf-behave-p2p-state]. o Alternatively, the Relay Client can learn it from the REG_FROM parameter when registering to a Relay. 3.2. Base Exchange via HIP Relay It is RECOMMENDED that the Initiator sends an I1 packet encapsulated in UDP when it is destined to an IPv4 address of the Responder. Respectively, the Responder MUST respond to a such I1 packet with an R1 packet over the transport layer and using the same transport protocol. The rest of the base exchange, I2 and R2, MUST also use the same transport layer. I HIP Relay R | 1. UDP(I1) | | +----------------------------->| 2. UDP(I1(RELAY_FROM)) | | +------------------------------->| | | | | | 3. UDP(R1(RELAY_TO)) | | 4. UDP(R1(RELAY_TO)) |<-------------------------------+ |<-----------------------------+ | | | | | 5. UDP(I2(LOCATOR)) | | +----------------------------->| | | | 6. UDP(I2(LOCATOR,RELAY_FROM)) | | +------------------------------->| | | | | | 7. UDP(R2(LOCATOR,RELAY_TO)) | | 8. UDP(R2(LOCATOR,RELAY_TO)) |<-------------------------------+ |<-----------------------------+ | | | | Figure 2: Base Exchange via a HIP Relay In step 1 of Figure 2, the Initiator sends an I1 packet over the transport layer to the HIT of the Responder. The source address is one of the locators of the host. The locators of the end-hosts are referred as "host candidates" in this document. In step 2, the HIP Relay receives the I1 packet at port HIPPORT. If the destination HIT belongs to a registered Responder, the Relay processes the packet. Otherwise, the Relay MUST drop the packet silently. The Relay appends a RELAY_FROM parameter to the I1 packet which constains the transport source address and port of the I1 as observed by the Relay. The Relay protects the I1 packet with RELAY_HMAC as described in [I-D.ietf-hip-rvs], except that the Komu, et al. Expires August 28, 2008 [Page 9] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 parameter type is different. The Relay changes the source and destination ports and IP addresses of the packet to match the values the Responder used when registering to the Relay, i.e., the reverse of the R2 used in the registration. The Relay MUST recalculate the transport checksum and forward the packet to the Responder. In step 3, the Responder receives the I1 packet. The Responder processes it according to the rules in [I-D.ietf-hip-base]. In addition, the Responder validates the RELAY_HMAC according to [I-D.ietf-hip-rvs] and silenty drops the packet if the validation fails. The Responder replies with an R1 packet to which it includes a RELAY_TO parameter. The RELAY_TO parameter contains same information as the RELAY_FROM parameter, i.e., Initiator transport address, but the type of the parameter is different. The RELAY_TO parameter is not integrity protected by the signature of the R1 to allow pre-created R1 packets at the Responder. In step 4, the Relay receives the R1 packet. The Relay drops the packet silently if the source HIT belongs to an unregistered host. The Relay MAY verify the signature of the R1 packet and drop it if the signature is invalid. Otherwise, the Relay rewrites to source address and port, changes the destination address and port to match RELAY_TO information, recalculates transport checksum and forwards the packet. In step 5, the Initiator receives the R1 packet and processes it according to [I-D.ietf-hip-base]. It replies with an I2 packet that uses the destination transport address of R1 as the source address and port. The I2 contains a LOCATOR parameter that lists all the ICE candidates (offer) of the Initiator. The candidates are encoded using the format defined in Section 5.4. In step 6, the Relay receives the I2 packet. The relay appends a RELAY_FROM and a RELAY_HMAC to the I2 packet as in the second step. In step 7, the Responder receives the I2 packet and processes it according to [I-D.ietf-hip-base]. It replies with a R2 packet and includes a RELAY_TO parameter as in step three. The R2 packet includes a LOCATOR parameter that lists all the ICE candidates (answer) of the Responder. The RELAY_TO parameter is protected by the HMAC. In step 8, the Relay processes the R2 as described in step four. The Relay forwards the packet to the Responder. Komu, et al. Expires August 28, 2008 [Page 10] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 4. Connectivity Tests 4.1. NAT Transformation Negotiation This section describes usage of a new optional transform parameter type. The presence of the parameter in HIP base exchange means that the host supports all of the extensions defined in this document. If the transform parameter is used, hosts MUST use a password for STUN HMACs that is drawn from the DH keying material. The transform parameter applies both to the registration to the HIP Relay as well as to a base exchange between end-hosts. The transform negotiation in base exchange is illustrated in Figure 3. Initiator Responder | 1. UDP(I1) | +------------------------------------------------------------->| | | | 2. UDP(R1(.., NAT_TRANSFORM(list of transforms), ..)) | |<-------------------------------------------------------------+ | | | 3. UDP(I2(.., NAT_TRANSFORM(selected transform), LOCATOR..)) | +------------------------------------------------------------->| | | | 4. UDP(R2(.., LOCATOR, ..)) | |<-------------------------------------------------------------+ | .... | Figure 3: Negotiation of NAT Transforms In step 1, the Initiator sends an I1 to the Responder. In step 2, the Responder responds with an R1. The R1 contains a list of transforms the Responder supports in NAT_TRANSFORM parameter as shown in Table 1. +--------------+----------------------------------------------------+ | Transform | Purpose | | Type | | +--------------+----------------------------------------------------+ | RESERVED | Reserved for future use | | ICE-STUN-UDP | UDP encapsulated control and data traffic with | | | ICE-based connectivity tests using STUN messages | +--------------+----------------------------------------------------+ Table 1: Locator Transformations In step 3, the Initiator sends an I2 that includes a NAT_TRANSFORM parameter. It contains the transform type selected by the Initiator Komu, et al. Expires August 28, 2008 [Page 11] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 from the list of transforms offered by the Responder. The I2 also includes the locators of the Initiator in a LOCATOR parameter. In step 4, the Responder concludes the base exchange with an R2 packet. The Responder includes a LOCATOR parameter in the R2 packet. 4.2. ICE Procedure Hosts exchange HIP control packets through the HIP Relay. Connectivity tests are, however, directly exchanged between the address pairs to determine operational address pairs. If a working direct path between the hosts is found, also the HIP control traffic MAY start using it. The base exchange is completed with an R2 packet. Then, the state of the HIP associations at both peers is ESTABLISHED, but the peers MUST NOT allow any ESP traffic until the connectivity tests are performed successfully. All of the locators, except the HIP Relay address, are in UNVERIFIED state. In the connectivity tests, the hosts test connectivity between different locator pairs in order to find a working one. The connectivity tests are illustrated in Figure 4. In this example, both hosts are behind NATs. I HIP Relay R | 2. UDP(R2(LOCATOR,RELAY_TO)) | 1. UDP(R2(LOCATOR,RELAY_TO)) | |<------------------------------+-------------------------------| | | | 3. Connectivity tests for address pairs | |<------------------------------------------------------------->| | | | 4. HIP UPDATE for preferred address pair | |<------------------------------------------------------------->| | | Figure 4: Connectivity tests In steps 1 and 2, the R2 packet is relayed from the Responder through the Relay to the Initiator. Afterwards, connectivity tests are started based on the procedure described in [I-D.rosenberg-mmusic-ice-nonsip] by using the candiates previously exchanged in the HIP base exchange. 4.3. NAT Keep-alives Data channel keepalives are STUN Binding Indications. Keepalives MUST be sent every 20 seconds at the minimum when the channel is idle. To implement failure tolerance, a host SHOULD have smaller Komu, et al. Expires August 28, 2008 [Page 12] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 keepalive period. When data traffic is exchanged between the end points then no further STUN keepalives need to be exchanged. 5. Packet Formats The following subsections define the parameter and packet encodings. All values MUST be in network byte order. 5.1. HIP Control Packets 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Port | Destination Port | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Length | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 32 bits of zeroes | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | ~ HIP Header and Parameters ~ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 5: Format for UDP-encapsulated HIP Control Packets HIP control packets are encapsulated in UDP packets like in Section 2.2 of [RFC3948], "rules for encapsulating IKE messages", except that a different port number is used. Figure 5 shows the encapsulation: UDP header is followed by 32 zero bits that can be used to differentiate HIP control packets from ESP packets. The HIP header and parameters follow the conventions of [I-D.ietf-hip-base] with the exception that the HIP header checksum MUST be zero. The HIP header checksum is zero for two reasons. First, the UDP header contains already a checksum. Second, the checksum definition in [I-D.ietf-hip-base] includes the IP addresses in the checksum calculation. The NATs unaware of HIP cannot recompute the HIP checksum after changing IP addresses. A HIP Relay or a Responder without a relay MUST listen at transport port HIPPORT for incoming UDP-encapsulated HIP control packets. 5.2. Keep-Alives Control and data channel keep-alives are STUN Binding Indications, as defined in [I-D.ietf-behave-rfc3489bis]. They use the same UDP header as the HIP control packets but there is no non-ESP-marker Komu, et al. Expires August 28, 2008 [Page 13] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 between the UDP header and the STUN header. STUN messages are demultiplexed from ESP and HIP control messages using the STUN markers, such as the magic cookie value. 5.3. Relay and Registration Parameters 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | Address | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Port | Transport | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type [ TBD by IANA: RELAY_FROM: (63998 = 2^16 - 2^11 + 2^9 - 2) RELAY_TO: (64002 = 2^16 - 2^11 + 2^9 + 2) REG_FROM: (64010 = 2^16 - 2^11 + 2^9 + 10) ] Length 20 Address An IPv6 address or an IPv4 address in "IPv4-compatible IPv6 address" format Port Transport port number; zero when plain IP is used Transport Transport protocol type; zero for UDP Figure 6: Format for the RELAY_FROM, RELAY_TO and REG_FROM parameters Format of the RELAY_FROM, RELAY_TO and REG_FROM parameters is shown in Figure 6. Parameters are identical except for the type field. 5.4. LOCATOR Parameter The generic LOCATOR parameter format is the same as in [I-D.ietf-hip-mm]. However, presenting ICE candidates requires a new locator type. The generic and NAT traversal specific locator parameters are illustrated in Figure 7. Komu, et al. Expires August 28, 2008 [Page 14] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Traffic Type | Locator Type | Locator Length| Reserved |P| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Locator Lifetime | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Locator | | | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ . . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Traffic Type | Loc Type = 2 | Locator Length| Reserved |P| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Locator Lifetime | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Transport Port | Transp. Proto| Kind | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Priority | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SPI | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Locator | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 7: LOCATOR parameter The individual fields in the LOCATOR parameter are described in Table 2. Komu, et al. Expires August 28, 2008 [Page 15] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 +-----------+----------+--------------------------------------------+ | Field | Value(s) | Purpose | +-----------+----------+--------------------------------------------+ | Type | 193 | Parameter type | | Length | Variable | Length in octets, excluding Type and | | | | Length fields and padding | | Traffic | 0-2 | Is the locator for HIP signaling (1), for | | Type | | ESP (2), or for both (0) | | Locator | 2 | "Transport address" locator type | | Type | | | | Locator | 7 | Length of the Locator field in 4-octet | | Length | | units | | Reserved | 0 | Reserved for future extensions | | Preferred | 0 | Not used for transport address locators; | | (P) bit | | MUST be ignored by the receiver. | | Locator | Variable | Locator lifetime in seconds | | Lifetime | | | | Transport | Variable | Transport layer port number | | Port | | | | Transport | 0 | 0 for UDP | | Protocol | | | | Kind | Variable | 0 for host, 1 for server reflexive, 2 for | | | | peer reflexive or 3 for relayed address | | Priority | Variable | Locator's priority as described in | | | | [I-D.ietf-mmusic-ice] | | SPI | Variable | SPI value which the host expects to see in | | | | incoming ESP packets that use this locator | | Locator | Variable | IPv6 address or an "IPv4-compatible IPv6 | | | | address" format IPv4 address [RFC3513], | | | | obfuscated by XORring it with the owner's | | | | HIT | +-----------+----------+--------------------------------------------+ Table 2: Fields of the LOCATOR parameter 5.5. RELAY_HMAC The RELAY_HMAC parameter value has the TLV type 65520 (2^16 - 2^5 + 2^4). It has the same semantics as RVS_HMAC [I-D.ietf-hip-rvs]. 5.6. Registration Types The REG_INFO, REQ_REQ, REG_RESP and REG_FAILED parameters contain values for HIP Relay registration. The value for RELAY_UDP_HIP is 2. The value for RELAY_UDP_ESP is 3. Komu, et al. Expires August 28, 2008 [Page 16] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 5.7. HIP ESP Data Packet Formats [RFC3948] describes UDP encapsulation of the IPsec ESP transport and tunnel mode. On the wire the HIP ESP packets do not differ from the transport mode ESP and thus the encapsulation of the HIP ESP packets is same as the UDP encapsulation transport mode ESP. During the HIP base exchange, the two peers exchange parameters that enable them to define a pair of IPsec ESP security associations (SAs), as described in [I-D.ietf-hip-esp]. When two peers perform a UDP-encapsulated base exchange, they MUST define a pair of IPsec SAs that produces UDP-encapsulated ESP data traffic. The management of encryption/authentication protocols and security parameter indices (SPIs) is defined in [I-D.ietf-hip-esp]. The UDP encapsulation format and processing of HIP ESP traffic is described in Section 6.1 of [I-D.ietf-hip-esp]. Section 5.1 of [RFC3948] describes a security issue for the UDP encapsulation in the standard IP tunnel mode when two hosts behind different NATs have the same private IP address and initiate communication to the same Responder in the public Internet. The Responder cannot distinguish between two hosts, because security associations are based on the same inner IP addresses. This issue does not exist with the UDP encapsulation of HIP ESP transport format because the Responder use HITs to distinguish between different communication instances. 6. Security Considerations 6.1. Privacy Considerations The LOCATORs are sent XORed format in plain text in favour of inspection at HIP-aware middleboxes in the future. The current draft does not specify encrypted versions of LOCATORs even though it could be beneficial for privacy reasons. It is possible that an Initiator or Responder may not want to reveal all of its locators to its peer. For example, a host may not want to reveal the internal topology of the private address realm and it discards host addresses. Such behavior creates non-optimal paths when the hosts are located behind the same NAT. Especially, this could be a problem with a legacy NAT that does not support routing from the private address realm back to itself through the outer address of the NAT. This scenario is referred to as the hairpin problem [I-D.ietf-behave-p2p-state]. With such a legacy NAT, the Komu, et al. Expires August 28, 2008 [Page 17] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 only option left would be to use a relayed transport address from a TURN server. As a consequence, a host may support locator-based privacy by leaving out the reflexive candidates. Using only host candidates can produce suboptimal paths possibly causing congestion. The use of HIP Relays or TURN Relays can be useful for protection against Denial-of-Service attacks. If a Responder reveals only its HIP and ESP relay candidates to malign Initiators, the Initiators can only attack the relays that does not prevent the Responder from initiating new outgoing connections if a path around the relay exists. 6.2. Opportunistic Mode A HIP Relay should have one address per Relay Client when a HIP Relay is serving more than one Relay Clients and is willing to support opportunistic mode. Otherwise, it cannot be guaranteed that the Relay can deliver the I1 packet to the intended recipient. 7. IANA Considerations This section is to be interpreted according to [RFC2434]. This draft currently uses a UDP port in the "Dynamic and/or Private Port" and HIPPORT. Upon publication of this document, IANA is requested to register a UDP port and the RFC editor is requested to change all occurrences of port HIPPORT to the port IANA has registered. The HIPPORT number 50500 should be used for initial experimentation. This document updates the IANA Registry for HIP Parameter Types by assigning new HIP Parameter Type values for the new HIP Parameters: RELAY_FROM, RELAY_TO and REG_FROM (defined in Section 5.3) and RELAY_HMAC (defined in Section 5.5). 8. Contributors Marcelo Bagnulo, Jan Melen, Simon Schuetz, Martin Stiemerling, Lars Eggert, Vivien Schmitt, Abhinav Pathak and Andrei Gurtov have contributed to the initial versions of this draft. 9. Acknowlegements Thanks for Jonathan Rosenberg and the rest of the MMUSIC WG folks for the excellent work on ICE. In addition, the authors would like to Komu, et al. Expires August 28, 2008 [Page 18] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 thank Andrei Gurtov, Tobias Heer, Teemu Koponen, Juhana Mattila, Jeffrey M. Ahrenholz, Thomas Henderson, Kristian Slavov, Janne Lindqvist, Pekka Nikander, Lauri Silvennoinen, Jukka Ylitalo, Juha Heinanen, Joakim Koskela, Samu Varjonen, Dan Wing, Hannes Tschofenig, Jan Melen, Jani Hautakorpi and Ari Keraenen For their comments on this document. Miika Komu is working in the Networking Research group at Helsinki Institute for Information Technology (HIIT). The InfraHIP project was funded by Tekes, Telia-Sonera, Elisa, Nokia, the Finnish Defence Forces, and Ericsson and Birdstep. 10. References 10.1. Normative References [I-D.ietf-behave-rfc3489bis] Rosenberg, J., Mahy, R., Matthews, P., and D. Wing, "Session Traversal Utilities for (NAT) (STUN)", draft-ietf-behave-rfc3489bis-15 (work in progress), February 2008. [I-D.ietf-behave-turn] Rosenberg, J., Mahy, R., and P. Matthews, "Traversal Using Relays around NAT (TURN): Relay Extensions to Session Traversal Utilities for NAT (STUN)", draft-ietf-behave-turn-06 (work in progress), January 2008. [I-D.ietf-hip-base] Moskowitz, R., Nikander, P., Jokela, P., and T. Henderson, "Host Identity Protocol", draft-ietf-hip-base-10 (work in progress), October 2007. [I-D.ietf-hip-esp] Jokela, P., "Using ESP transport format with HIP", draft-ietf-hip-esp-06 (work in progress), June 2007. [I-D.ietf-hip-mm] Henderson, T., "End-Host Mobility and Multihoming with the Host Identity Protocol", draft-ietf-hip-mm-05 (work in progress), March 2007. [I-D.ietf-hip-registration] Laganier, J., "Host Identity Protocol (HIP) Registration Extension", draft-ietf-hip-registration-02 (work in progress), June 2006. Komu, et al. Expires August 28, 2008 [Page 19] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 [I-D.ietf-hip-rvs] Laganier, J. and L. Eggert, "Host Identity Protocol (HIP) Rendezvous Extension", draft-ietf-hip-rvs-05 (work in progress), June 2006. [I-D.ietf-mmusic-ice] Rosenberg, J., "Interactive Connectivity Establishment (ICE): A Protocol for Network Address Translator (NAT) Traversal for Offer/Answer Protocols", draft-ietf-mmusic-ice-19 (work in progress), October 2007. [I-D.rosenberg-mmusic-ice-nonsip] Rosenberg, J., "NICE: Non Session Initiation Protocol (SIP) usage of Interactive Connectivity Establishment (ICE)", draft-rosenberg-mmusic-ice-nonsip-00 (work in progress), February 2008. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2434] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 2434, October 1998. [RFC3513] Hinden, R. and S. Deering, "Internet Protocol Version 6 (IPv6) Addressing Architecture", RFC 3513, April 2003. [RFC4423] Moskowitz, R. and P. Nikander, "Host Identity Protocol (HIP) Architecture", RFC 4423, May 2006. 10.2. Informative References [I-D.ietf-behave-p2p-state] Srisuresh, P., Ford, B., and D. Kegel, "State of Peer-to- Peer(P2P) Communication Across Network Address Translators(NATs)", draft-ietf-behave-p2p-state-06 (work in progress), November 2007. [I-D.irtf-hiprg-nat] Stiemerling, M., "NAT and Firewall Traversal Issues of Host Identity Protocol (HIP) Communication", draft-irtf-hiprg-nat-04 (work in progress), March 2007. [RFC2663] Srisuresh, P. and M. Holdrege, "IP Network Address Translator (NAT) Terminology and Considerations", RFC 2663, August 1999. [RFC3948] Huttunen, A., Swander, B., Volpe, V., DiBurro, L., and M. Komu, et al. Expires August 28, 2008 [Page 20] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 Stenberg, "UDP Encapsulation of IPsec ESP Packets", RFC 3948, January 2005. [RFC4787] Audet, F. and C. Jennings, "Network Address Translation (NAT) Behavioral Requirements for Unicast UDP", BCP 127, RFC 4787, January 2007. Appendix A. Firewall Traversal This section describes firewall traversal issues separately from NAT issues. When the Initiator or the Responder of a HIP association is behind a firewall, additional issues arise. The firewall discussion applies both to IPv4 and IPv6 addressing. The NAT traversal mechanisms described in this document require that the firewall - stateful or not - allows UDP traffic. At the minimum, successful firewall control packet traversal requires that the host behind the firewall is allowed to communicate packets with a HIP Relay (or a Responder without HIP Relay) that is listening on UDP port HIPPORT. Successful ESP data packet traversal requires the same for the TURN server. For unrelayed traffic, the destination port HIPPORT should be open at the firewall to all hosts behind the firewall. Most firewall implementations support "UDP connection tracking", i.e., after a host behind a firewall has initiated UDP communication to the public Internet, the firewall accepts UDP response traffic in the return direction. If no such return traffic arrives for a specific period of time, the firewall stops accepting the given IP address and port pair. The mechanisms described in this document already enable traversal of such firewalls, if the keep-alive interval used is less than the refresh interval of the firewall. When the Initiator is behind a firewall, the NAT traversal mechanisms described in this document depend on the ability to initiate communication via UDP to the destination port HIPPORT from arbitrary source ports and to receive UDP response traffic from that port to the chosen source port. If the Initiator is behind a firewall that does not support "UDP connection tracking", the NAT traversal mechanisms described in this document can still be supported, if the firewall allows permanently inbound UDP traffic from the port HIPPORT and destined to arbitrary source IP addresses and UDP ports. When the Responder is behind a firewall, the NAT traversal mechanisms described in this document depend on the ability to send and receive UDP traffic originating from HIPPORT of the HIP Relays and TURN servers. When end-to-end traffic is preferred, arbitrary source IP Komu, et al. Expires August 28, 2008 [Page 21] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 addresses and ports are required. Appendix B. Base Exchange without ICE Connectivity Checks In certain network environments, the ICE connectivity tests can be omitted to reduce initial connection set up latency because base exchange acts an implicit connectivity test itself. There are three assumptions about such as environments. First, the Responder should have a long-term, fixed locator in the network. Second, the Responder should not have a HIP Relay configured for itself. Third, the Initiator can reach the Responder by simply UDP encapsulating HIP and ESP packets to the host. Detecting and configuring this particular scenario is prone administrative failure unless carefully planned. In such a scenario, the Initiator sends an I1 packet over UDP to the Responder. The Responder replies with a R1 packet that does not contain the transform parameter as explained in Section 4.1. The Initiator receives the R1 packet and determines from the absence of the transform and RELAY_TO parameters that ICE connectivity tests can be omitted with the Responder. Finally, the hosts set up IPsec security associations using the locators observed from the concluding I2 and R2 packets of the base exchange without ICE connectivity tests. Appendix C. IPv4-IPv6 Interoperability Currently Relay Client and Server do not have to run any ICE connectivity tests as described in Appendix B. However, it could be useful for IPv4-IPv6 interoperability when the Relay Server actually includes both the NAT transform parameter and multiple locators in R2. The interoperability benefit is that the Relay could support IPv4-based Initiators and IPv6-based Responders by converting the network headers and recalculating UDP checksums. Such an approach is underspecified in this document currently. It is not yet recommended because it may consume resources at the Relay and requires also similar conversion support at the TURN relay for data packets. Appendix D. Base Exchange through a Rendezvous Server This section describes handling for a scenario where Initiator looks up the information of the Responder from DNS and discovers a RVS record [I-D.ietf-hip-rvs]. In such a case, the Initiator uses its Komu, et al. Expires August 28, 2008 [Page 22] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 own HIP Relay to forward HIP traffic to the Rendezvous server. The Initiator will send the I1 message using the its HIP Relay server which will then forward it to the RVS server of the responder. The responder will send the R1 packet directly to the Initiator's HIP Relay server and the following I2 and R2 packets are also sent directly using the Relay. In case the Initiator is not able to distinguish which records are RVS address records and which are Responders address records, then the Initiator SHOULD first try to contact the Responder directly and if none of the addresses is reachable it MAY try out them using its own HIP Relay as described in the above. Appendix E. Document Revision History To be removed upon publication +-----------------------------+-------------------------------------+ | Revision | Comments | +-----------------------------+-------------------------------------+ | draft-ietf-nat-traversal-00 | Initial version. | | draft-ietf-nat-traversal-01 | Draft based on RVS. | | draft-ietf-nat-traversal-02 | Draft based on Relay proxies and | | | ICE concepts. | | draft-ietf-nat-traversal-03 | Draft based on STUN/ICE formats. | +-----------------------------+-------------------------------------+ Authors' Addresses Miika Komu Helsinki Institute for Information Technology Metsanneidonkuja 4 Espoo Finland Phone: +358503841531 Fax: +35896949768 Email: miika@iki.fi URI: http://www.hiit.fi/ Komu, et al. Expires August 28, 2008 [Page 23] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 Thomas Henderson The Boeing Company P.O. Box 3707 Seattle, WA USA Email: thomas.r.henderson@boeing.com Philip Matthews Avaya 100 Innovation Drive Ottawa, Ontario K2K 3G7 Canada Phone: +1 613 592 4343 224 Email: philip_matthews@magma.ca Hannes Tschofenig Nokia Siemens Networks Linnoitustie 6 Espoo 02600 Finland Phone: +358 (50) 4871445 Email: Hannes.Tschofenig@gmx.net URI: http://www.tschofenig.com Ari Keraenen Ericsson Research Nomadiclab Hirsalantie 11 02420 Jorvas Finland Phone: +358 9 2991 Email: ari.keranen@ericsson.com Komu, et al. Expires August 28, 2008 [Page 24] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 Jan Melen Ericsson Research Nomadiclab Hirsalantie 11 02420 Jorvas Finland Phone: +358 9 2991 Email: jan.melen@ericsson.com Marcelo Bagnulo Huawei Lab at UC3M Av. Universidad 30 Leganes, Madrid 28911 Spain Phone: 34 91 6249500 Email: marcelo@it.uc3m.es URI: http://www.it.uc3m.es/ Komu, et al. Expires August 28, 2008 [Page 25] Internet-Draft Basic NAT and Firewall Traversal for HIP February 2008 Full Copyright Statement Copyright (C) The IETF Trust (2008). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Acknowledgment Funding for the RFC Editor function is provided by the IETF Administrative Support Activity (IASA). Komu, et al. Expires August 28, 2008 [Page 26]