Ethernet Interfaces and Hub MIB Working Group Lior Khermosh, Editor INTERNET DRAFT Passave Technologies April 29, 2004 Managed Objects for the Ethernet Passive Optical Networks Status of this Memo This document is an Internet-Draft and is subject to all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsolete by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html Copyright Notice Copyright (C) The Internet Society (2003). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. EPON MIB WG Expires October 2004 [Page 1] Internet-Draft EPON MIBs April 29, 2004 Abstract This document defines a portion of the Management Information Base (MIB) for use with network management protocols in TCP/IP based Internets. In particular, it defines objects for managing devices and interfaces that conform to the Ethernet Passive Optical Networks (EPON) standards as defined in [802.3ah]. The document contains a list of management entities based on the registers defined in the Institute of Electrical and Electronic Engineers, IEEE Draft 802.3ah-2002 Draft 3.2 Annex 30A and mainly partitioned accordingly. EPON MIB WG Expires October 2004 [Page 2] Internet-Draft EPON MIBs April 29, 2004 Table of Content Status of this Memo 1 Copyright Notice 1 Abstract 2 Table of Content 3 Terminology 4 1 The Internet-Standard Management Framework 4 2 Overview 4 2.1 Relationship of the EFM EPON MIB to the Interfaces MIB , the Ethernet-like Interfaces MIB and the MAU MIB 4 2.2 Relationship of the EFM EPON MIB to the Generic EFM MIB 4 2.3 Relationship of the EPON Device MIB to the EFM EPON MIB 4 2.4 Relationship of the EPON Device MIB to the Optical Interface MIBs 5 2.5 Relationship of the EPON Device MIB to the bridge MIB 5 3 MIB structure 5 4 Definitions û The EFM EPON MIB 6 5 Relationship table of the EFM EPON MIBs objects to the IEEE802.3ah objects 32 6 Definitions - The EPON Device MIB 34 7 Security Considerations 63 8 Intellectual Property 64 9 Normative References 65 10 Informative References 66 Copyright Notice 67 AuthorÆs information 67 EPON MIB WG Expires October 2004 [Page 3] Internet-Draft EPON MIBs April 29, 2004 Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL", when used in the guidelines in this memo, are to be interpreted as described in RFC 2119 [RFC2119]. 1 The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580]. 2 Overview This document defines a portion of the Management Information Base (MIB) for use with network management protocols in TCP/IP based Internets. In particular, it defines objects for managing devices and interfaces that conform to the Ethernet Passive Optical Networks (EPON) standards as defined in [802.3ah]. The document contains a list of management entities based on the registers defined in the [802.3ah] Annex 30A and mainly partitioned accordingly. The document also contains a device group section defining the MIBs for EPON form a device perspective, which are connected directly to the IEEE 802.3ah layer2 specifications. The document also provides amendments to the 802.3 MAU MIBs documents for the EFM device type addition. 2.1 Relationship of the EFM EPON MIB to the Interfaces MIB, the Ethernet-like Interfaces MIB and the MAU MIB EFM EPON interfaces require implementation of Interfaces MIB [RFC2863], Ethernet-like Interfaces MIB [RFC2665] and MAU-MIB [RFC3636]. The MIBs defined in this document are an extension for these MIBs. For instance defining dot3MpcpRemoteMACAddress only while assuming the local MAC address attribute is already defined in [RFC 2665]. 2.2 Relationship of the EFM EPON MIB to the Generic EFM MIB EFM EPON interfaces require implementation of Generic EFM MIB [draft- ietf-hubmibùefm-mib]. This document defines general EFM attributes and managed objects that are referred in the document. 2.3 Relationship of the EPON Device MIB to EFM EPON MIB EPON devices require implementation of the EFM EPON MIBs which are EPON MIB WG Expires October 2004 [Page 4] Internet-Draft EPON MIBs April 29, 2004 specified in this document. The opposite is not required as it possible to implement the EFM interfaces by itself. 2.4 Relationship of the EPON Device MIB to Optical interface MIB EPON devices may implement the Optical interface MIB [RFC3591]. This document defines optical interface attributes and managed objects that are assumed to be used by an EPON device. 2.5 Relationship of the EPON Device MIB to bridge MIB EPON OLT devices may implement the bridge MIBs [RFC1493], [RFC1525], Where the LLIDs of the PON are referred as the bridge ports. This document defines managed objects for a bridge that are assumed to be used by an EPON OLT device which bridges the data between the LLIDs of the PON. 3 MIB structure This document includes two MIBs the first is the EFM EPON MIBs and the second is the EPON device MIBs. The EFM EPON MIBs defines the objects used for configuration and description of the [802.3ah] P2MP section. These MIB objects are included of three MIB groups. The MPCP MIBs definition û MIBs related to [802.3ah] clause 64 Multi Point Control Protocol attributes. In this MIB group: The dot3MpcpTable defines the objects used for the configuration and description of the status of MPCP compliant interfaces. The dot3MpcpStatTable defines the statistics group for MPCP compliant interfaces. The OMPEmulation MIBs definitions û MIBs related to [802.3ah] clause 65 point to point emulation attributes. In this MIB group: The dot3OmpEmulationTable defines the objects used for the configuration and description of the status of OMPEmulation compliant interfaces. The dot3OmpEmulationStatTable defines the statistics group for OMPEmulation compliant interfaces. The MAU MIBs definition including MAU type definitions and EPON MAU managed object related to [802.3ah] clause 60 and clause 65. The dot3EponMauTable defines the objects used for the configuration and description of the status of MAU EPON compliant interfaces. The dot3EponMauType defines the Type group for [802.3] EPOM MAUs. Editor note - The MAU Type object should probably be with other 802.3 MAU type objects [RFC 3636]. The EPON Device MIBs defines the objects used for configuration and description of management objects for EPON compliant Devices. The eponDeviceTable defines the objects used for the configuration and description of the EPON compliant devices. EPON MIB WG Expires October 2004 [Page 5] Internet-Draft EPON MIBs April 29, 2004 4 Definitions û The EFM EPON MIB (See section 30.2.5 in 802.3ah draft for details): DOT3-EFM-EPON-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, mib-2, OBJECT-TYPE, Counter32, Integer32, OBJECT-IDENTITY FROM SNMPv2-SMI TruthValue, MacAddress FROM SNMPv2-TC ifIndex FROM IF-MIB MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ; dot3EfmeponMIB MODULE-IDENTITY LAST-UPDATED "200404290000Z" -- April 29, 2004 ORGANIZATION "IETF Ethernet Interfaces and Hub MIB Working Group" CONTACT-INFO "WG charter: http://www.ietf.org/html.charters/hubmib-charter.html Mailing Lists: General Discussion: hubmib@ietf.org To Subscribe: hubmib-request@ietf.org In Body: subscribe your_email_address Chair: Dan Romascanu Postal: Avaya Inc. Atidim Technology Park, Bldg. 3 Tel Aviv 61131 Israel Tel: +972-3-645-8414 E-mail: dromasca@avaya.com Editor: Lior Khermosh Postal: Passave Technologies Inc. Ackerstein Towers, Tower A, 6th floor, 9 Hamenofim St. Hertzliya Pituach 46725, ISRAEL P.O.Box 2089 Hertzliya Pituach 46120 Israel Tel: +972-9-9717600 Ext: 7181 E-mail: lior.khermosh@passave.com" DESCRIPTION "The objects in this MIB module are used to manage EPON MIB WG Expires October 2004 [Page 6] Internet-Draft EPON MIBs April 29, 2004 the Ethernet in the First Mile (EFM) Multi Point Control Protocol (MPCP) Interfaces as defined in IEEE Draft P802.3ah/D3.0 clause 64,65. The following reference is used throughout this MIB module: [802.3ah] refers to: IEEE Draft P802.3ah/D3.3: 'Draft amendment to - Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications - Media Access Control Parameters, Physical Layers and Management Parameters for subscriber access networks', 22 April 2004. Of particular interest are Clause 64(MPCP) 65(P2mP RS) and 60 (PON PMDs). Clause 30, 'Management', and Clause 45,'Management Data Input/Output (MDIO) Interface'. Copyright (C) The Internet Society (2003). This version of this MIB module is part of XXXX see the RFC itself for full legal notices." -- Editor's Note: Replace XXXX with the actual RFC number -- assigned by RFC Editor and remove this note REVISION "200404290000Z" -- April 29, 2004 DESCRIPTION "Initial version, published as RFC XXXX." ::= { mib-2 XXX } -- Editor's Note: Replace XXX with a real OID once it is -- assigned by IANA and remove this note. -- EditorÆs note: MPCP MIBs definitions ([802.3ah] clause 30.3.5) -- EditorÆs note: Description in attributes with References should be -- minimized in later versions dot3MpcpMIB OBJECT IDENTIFIER ::= { dot3EfmeponMIB 1} dot3MpcpObjects OBJECT IDENTIFIER ::= { dot3MpcpMIB 1} dot3MpcpConformance OBJECT IDENTIFIER ::= { dot3MpcpMIB 2} dot3MpcpTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3MpcpEntry EPON MIB WG Expires October 2004 [Page 7] Internet-Draft EPON MIBs April 29, 2004 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for dot3 MPCP MIBs." ::= { dot3MpcpObjects 1 } dot3MpcpEntry OBJECT-TYPE SYNTAX Dot3MpcpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the dot3 MPCP MIBs table." INDEX { ifIndex } ::= { dot3MpcpTable 1 } Dot3MpcpEntry ::= SEQUENCE { dot3MpcpID Integer32, dot3MpcpAdminState TruthValue, dot3MpcpMode INTEGER, dot3MpcpLinkID Integer32, dot3MpcpRemoteMACAddress MacAddress, dot3MpcpRegistrationState INTEGER, dot3MpcpTransmitElapsed Integer32, dot3MpcpReceiveElapsed Integer32, dot3MpcpRoundTripTime Integer32, dot3MpcpMaximumPendingGrants Integer32, dot3MPCPAdminControl TruthValue, dot3MpcpOnTime Integer32, dot3MpcpOffTime Integer32, dot3MpcpSyncTime Integer32 } dot3MpcpID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This variable is assigned so as to uniquely identify the Multi-Point MAC Control (MPCP) entity, as defined in [802.3ah] clause 64, among the subordinate managed objects of the containing object." REFERENCE "[802.3ah], 30.3.5.1.1." ::= { dot3MpcpEntry 1 } dot3MpcpAdminState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only EPON MIB WG Expires October 2004 [Page 8] Internet-Draft EPON MIBs April 29, 2004 STATUS current DESCRIPTION "This variable can be used to define the operational state of the Multi-Point MAC Control sublayer as defined in [802.3ah] clause 64. Selecting admin for an interface with Multi-Point MAC Control sublayer" REFERENCE "[802.3ah], 30.3.5.1.2." ::= { dot3MpcpEntry 2 } dot3MpcpMode OBJECT-TYPE SYNTAX INTEGER { olt(1), onu(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable can be used to identify the operational state of the Multi-Point MAC Control sublayer as defined in [802.3ah] clause 64. Selecting olt for an OLT (server) mode and onu for an ONU (client) mode." REFERENCE "[802.3ah], 30.3.5.1.3." ::= { dot3MpcpEntry 3 } dot3MpcpLinkID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that identifies the Logical Link identity (LLID) associated with the MAC port as specified in [802.3ah] clause 65.1.3.2.2." REFERENCE "[802.3ah], 30.3.5.1.4." ::= { dot3MpcpEntry 4 } dot3MpcpRemoteMACAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that identifies the source_address parameter of the last MPCPDUs passed to the MAC Control. This value is updated on reception of a valid frame with (1) a destination Field equal to the reserved multicast address for MAC Control specified in [802.3ah] Annex 31A, (2) lengthOrType field value equal to the reserved Type for MAC Control as specified in [802.3ah] Annex 31A. (3) an MPCP subtype value equal to the subtype reserved for MPCP as specified in [802.3ah] Annex 31A." EPON MIB WG Expires October 2004 [Page 9] Internet-Draft EPON MIBs April 29, 2004 REFERENCE "[802.3ah], 30.3.5.1.5." ::= { dot3MpcpEntry 5 } dot3MpcpRegistrationState OBJECT-TYPE SYNTAX INTEGER { unregistered(1), registering(2), registered(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that identifies the operational state of the Multi- Point MAC Control sublayer as defined in [802.3ah] clause 64. When this attribute has the enumeration 'unregistered' the interface may be used for registering a link partner. When this attribute has the enumeration 'registering' the interface is in the process of registering a link-partner. When this attribute has the enumeration 'registered' the interface has an established link-partner." REFERENCE "[802.3ah], 30.3.5.1.6." ::= { dot3MpcpEntry 6 } dot3MpcpTransmitElapsed OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that reports the interval from last MPCP frame transmission in increments of 16ns. The value returned shall be (interval from last MPCP frame transmission in ns)/16, where this value exceeds (2^32-1) the value (2^32-1) shall be returned." REFERENCE "[802.3ah], 30.3.5.1.19." ::= { dot3MpcpEntry 7 } dot3MpcpReceiveElapsed OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that reports the interval from last MPCP frame reception in increments of 16ns. The value returned shall be (interval from last MPCP last MPCP frame reception in ns)/16, where this value exceeds (2^32-1) the value (2^32-1) shall be returned." REFERENCE "[802.3ah], 30.3.5.1.20." ::= { dot3MpcpEntry 8 } dot3MpcpRoundTripTime OBJECT-TYPE EPON MIB WG Expires October 2004 [Page 10] Internet-Draft EPON MIBs April 29, 2004 SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that reports the MPCP round trip time in increments of 16ns. The value returned shall be (round trip time in ns)/16, where this value exceeds (2^16-1) the value (2^16-1) shall be returned." REFERENCE "[802.3ah], 30.3.5.1.21." ::= { dot3MpcpEntry 9 } dot3MpcpMaximumPendingGrants OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " A read-only value that indicates the maximum number of grants an ONU can store. The maximum number of grants an ONU can store has a range of 0 to 255." REFERENCE "[802.3ah], 30.3.5.1.24." ::= { dot3MpcpEntry 10 } dot3MPCPAdminControl OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This variable can be used to define the operational state of the Multi-Point MAC Control sublayer as defined in [802.3ah] clause 64. Selecting admin for an interface with Multi-Point MAC Control sublayer." REFERENCE "[802.3ah], 30.3.5.2.1." ::= { dot3MpcpEntry 11 } dot3MpcpOnTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that reports the æon timeÆ for a grant burst in increments of 16ns as defined in [802.3ah] 60,64. The value returned shall be (on time ns)/16, where this value exceeds (2^32-1) the value (2^32- 1) shall be returned." REFERENCE "[802.3ah], 64.3.5.1." ::= { dot3MpcpEntry 12 } dot3MpcpOffTime OBJECT-TYPE EPON MIB WG Expires October 2004 [Page 11] Internet-Draft EPON MIBs April 29, 2004 SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that reports the æoff timeÆ for a grant burst in increments of 16ns as defined in [802.3ah] 60,64. The value returned shall be (off time ns)/16, where this value exceeds (2^32-1) the value (2^32-1) shall be returned." REFERENCE "[802.3ah], 64.3.5.1." ::= { dot3MpcpEntry 13 } dot3MpcpSyncTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that reports the æsync lock timeÆ for an OLT receiver in increments of 16ns as defined in [802.3ah] 60,64,65. The value returned shall be (sync lock time ns)/16, where this value exceeds (2^32-1) the value (2^32-1) shall be returned." REFERENCE "[802.3ah], 64.3.3.2." ::= { dot3MpcpEntry 14 } dot3MpcpStatTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3MpcpStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines the list of statistics counters of [802.3ah] clause 64 MPCP interface." ::= { dot3MpcpObjects 2 } dot3MpcpStatEntry OBJECT-TYPE SYNTAX Dot3MpcpStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table entries for Table of statistics counters of [802.3ah] clause 64 MPCP interface." INDEX { ifIndex } ::= { dot3MpcpStatTable 1 } Dot3MpcpStatEntry ::= SEQUENCE { EPON MIB WG Expires October 2004 [Page 12] Internet-Draft EPON MIBs April 29, 2004 dot3MpcpMACCtrlFramesTransmitted Counter32, dot3MpcpMACCtrlFramesReceived Counter32, dot3MpcpDiscoveryWindowsSent Counter32, dot3MpcpDiscoveryTimeout Counter32, dot3MpcpTxRegRequest Counter32, dot3MpcpRxRegRequest Counter32, dot3MpcpTxRegAck Counter32, dot3MpcpRxRegAck Counter32, dot3MpcpTxReport Counter32, dot3MpcpRxReport Counter32, dot3MpcpTxGate Counter32, dot3MpcpRxGate Counter32, dot3MpcpTxRegister Counter32, dot3MpcpRxRegister Counter32, dot3MpcpRxNotSupportedMPCP Counter32 } dot3MpcpMACCtrlFramesTransmitted OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of MPCP frames passed to the MAC sublayer for transmission. This counter is incremented when a MA_CONTROL.request service primitive is generated within the MAC control sublayer with an opcode indicating a MPCP frame." REFERENCE "[802.3ah], 30.3.5.1.7." ::= { dot3MpcpStatEntry 1 } dot3MpcpMACCtrlFramesReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of MPCP frames passed by the MAC sublayer to the MAC Control sublayer. This counter is incremented when a ReceiveFrame function call returns a valid frame with: (1) a lengthOrType field value equal to the reserved Type for 802.3_MAC_Control as specified in 31.4.1.3, and (2) an opcode indicating a MPCP frame." REFERENCE "[802.3ah], 30.3.5.1.8." ::= { dot3MpcpStatEntry 2} dot3MpcpDiscoveryWindowsSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only EPON MIB WG Expires October 2004 [Page 13] Internet-Draft EPON MIBs April 29, 2004 STATUS current DESCRIPTION "A count of discovery windows generated. The counter is incremented by one for each generated discovery window." REFERENCE "[802.3ah], 30.3.5.1.22." ::= { dot3MpcpStatEntry 3} dot3MpcpDiscoveryTimeout OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a discovery timeout occurs. Increment the counter by one for each discovery processing state-machine reset resulting from timeout waiting for message arrival." REFERENCE "[802.3ah], 30.3.5.1.23." ::= { dot3MpcpStatEntry 4} dot3MpcpTxRegRequest OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a REGISTER_REQ MPCP frames transmission occurs. Increment the counter by one for each REGISTER_REQ MPCP frame transmitted as defined in [802.3ah] clause 64. This counter is mandatory for an ONU" REFERENCE "[802.3ah], 30.3.5.1.12." ::= { dot3MpcpStatEntry 5} dot3MpcpRxRegRequest OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a REGISTER_REQ MPCP frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each REGISTER_REQ MPCP frame received for each LLID as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and for an OLT" REFERENCE "[802.3ah], 30.3.5.1.17." ::= { dot3MpcpStatEntry 6} dot3MpcpTxRegAck OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only EPON MIB WG Expires October 2004 [Page 14] Internet-Draft EPON MIBs April 29, 2004 STATUS current DESCRIPTION " A count of the number of times a REGISTER_ACK MPCP frames transmission occurs. Increment the counter by one for each REGISTER_ACK MPCP frame transmitted as defined in [802.3ah] clause 64. This counter is mandatory for an ONU" REFERENCE "[802.3ah], 30.3.5.1.10." ::= { dot3MpcpStatEntry 7} dot3MpcpRxRegAck OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a REGISTER_ACK MPCP frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each REGISTER_ACK MPCP frame received for each LLID, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and for an OLT" REFERENCE "[802.3ah], 30.3.5.1.15." ::= { dot3MpcpStatEntry 8} dot3MpcpTxReport OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a REPORT MPCP frames transmission occurs. Increment the counter by one for each REPORT MPCP frame transmitted as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." REFERENCE "[802.3ah], 30.3.5.1.13." ::= { dot3MpcpStatEntry 9} dot3MpcpRxReport OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a REPORT MPCP frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each REPORT MPCP frame received for each LLID, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and for an OLT." REFERENCE "[802.3ah], 30.3.5.1.18." ::= { dot3MpcpStatEntry 10} EPON MIB WG Expires October 2004 [Page 15] Internet-Draft EPON MIBs April 29, 2004 dot3MpcpTxGate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a GATE MPCP frames transmission occurs. A set of counters, one for each LLID, at the OLT. Increment the counter by one for each GATE MPCP frame transmitted, for each LLID, as defined in [802.3ah] clause 64. This counter is mandatory for an OLT." REFERENCE "[802.3ah], 30.3.5.1.9." ::= { dot3MpcpStatEntry 11} dot3MpcpRxGate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a GATE MPCP frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each GATE MPCP frame received, for each LLID, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and for an OLT." REFERENCE "[802.3ah], 30.3.5.1.14." ::= { dot3MpcpStatEntry 12} dot3MpcpTxRegister OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a REGISTER MPCP frames transmission occurs. A set of counters, one for each LLID, at the OLT. Increment the counter by one for each REGISTER MPCP frame transmitted, for each LLID, as defined in [802.3ah] clause 64. This counter is mandatory for an OLT." REFERENCE "[802.3ah], 30.3.5.1.11." ::= { dot3MpcpStatEntry 13} dot3MpcpRxRegister OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a REGISTER MPCP frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each REGISTER MPCP frame received, for each LLID, as defined in [802.3ah] clause 64. This counter EPON MIB WG Expires October 2004 [Page 16] Internet-Draft EPON MIBs April 29, 2004 is mandatory for an ONU and for an OLT." REFERENCE "[802.3ah], 30.3.5.1.16." ::= { dot3MpcpStatEntry 14} dot3MpcpRxNotSupportedMPCP OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a non-supported MPCP frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each non- supported MPCP frame received, for each LLID, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and for an OLT." ::= { dot3MpcpStatEntry 15} -- Conformance Statements -- Conformance Groups dot3MpcpGroups OBJECT IDENTIFIER ::= { dot3MpcpConformance 1 } dot3MpcpGroupBase OBJECT-GROUP OBJECTS { dot3MpcpID, dot3MpcpAdminState, dot3MpcpMode, dot3MpcpLinkID, dot3MpcpRemoteMACAddress, dot3MpcpRegistrationState, dot3MpcpMaximumPendingGrants, dot3MPCPAdminControl } STATUS current DESCRIPTION "A collection of objects of dot3 Mpcp Basic entity state EPON MIB WG Expires October 2004 [Page 17] Internet-Draft EPON MIBs April 29, 2004 definition." ::= { dot3MpcpGroups 1 } dot3MpcpGroupParam OBJECT-GROUP OBJECTS { dot3MpcpTransmitElapsed, dot3MpcpReceiveElapsed, dot3MpcpRoundTripTime, dot3MpcpOnTime, dot3MpcpOffTime, dot3MpcpSyncTime } STATUS current DESCRIPTION "A collection of objects of dot3 Mpcp for P2MP parameters." ::= { dot3MpcpGroups 2 } dot3MpcpGroupStat OBJECT-GROUP OBJECTS { dot3MpcpMACCtrlFramesTransmitted, dot3MpcpMACCtrlFramesReceived, dot3MpcpDiscoveryWindowsSent, dot3MpcpDiscoveryTimeout , dot3MpcpTxRegRequest, dot3MpcpRxRegRequest, dot3MpcpTxRegAck, dot3MpcpRxRegAck, dot3MpcpTxReport, dot3MpcpRxReport, dot3MpcpTxGate, dot3MpcpRxGate, dot3MpcpTxRegister, dot3MpcpRxRegister, dot3MpcpRxNotSupportedMPCP } STATUS current DESCRIPTION "A collection of objects of dot3 Mpcp Statistics" ::= { dot3MpcpGroups 3 } EPON MIB WG Expires October 2004 [Page 18] Internet-Draft EPON MIBs April 29, 2004 -- Compliance dot3MpcpCompliances OBJECT IDENTIFIER ::= { dot3MpcpConformance 2 } dot3MPCPCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for Multi-point control protocol interfaces." MODULE -- this module MANDATORY-GROUPS { dot3MpcpGroupBase} GROUP dot3MpcpGroupParam DESCRIPTION "This group is mandatory for all MPCP supporting interfaces for configuration of the Multipoint Parametrs." GROUP dot3MpcpGroupStat DESCRIPTION " This group is mandatory for all MPCP supporting interfaces for Statistics collection." ::= { dot3MpcpCompliances 1} -- EditorÆs note: OMPEmulation managed object definitions dot3OmpEmulationMIB OBJECT IDENTIFIER ::= { dot3EfmeponMIB 2} dot3OmpEmulationObjects OBJECT IDENTIFIER ::= { dot3OmpEmulationMIB 1} dot3OmpeConformance OBJECT IDENTIFIER ::= { dot3OmpEmulationMIB 2 } dot3OmpEmulationTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3OmpEmulationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for dot3 OmpEmulation MIBs." ::= { dot3OmpEmulationObjects 1 } dot3OmpEmulationEntry OBJECT-TYPE EPON MIB WG Expires October 2004 [Page 19] Internet-Draft EPON MIBs April 29, 2004 SYNTAX Dot3OmpEmulationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the dot3 OmpEmulation MIBs table." INDEX { ifIndex } ::= { dot3OmpEmulationTable 1 } Dot3OmpEmulationEntry ::= SEQUENCE { dot3OmpEmulationID Integer32, dot3OmpEmulationType INTEGER } dot3OmpEmulationID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION " The value of aOAMID is assigned so as to uniquely identify a OMPEmulation entity among the subordinate managed objects of the containing object." REFERENCE "[802.3ah], 30.3.7.1.1." ::= { dot3OmpEmulationEntry 1} dot3OmpEmulationType OBJECT-TYPE SYNTAX INTEGER { unknown(1), olt(2), onu(3) } MAX-ACCESS read-only STATUS current DESCRIPTION " A read-only value that indicates that mode of operation of the Reconciliation Sublayer for Point to Point Emulation (see [802.3ah] clause 65.1). æunknownÆ value is assigned in initializing, true state or type not yet known. æoltÆ value is assigned when Sublayer operating in OLT mode. æonuÆ value is assigned when Sublayer operating in ONU mode." REFERENCE "[802.3ah], 30.3.7.1.2." ::= { dot3OmpEmulationEntry 2} dot3OmpEmulationStatTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3OmpEmulationStatEntry EPON MIB WG Expires October 2004 [Page 20] Internet-Draft EPON MIBs April 29, 2004 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines the list of statistics counters of [802.3ah] clause 65 OMP interface." ::= { dot3OmpEmulationObjects 2} dot3OmpEmulationStatEntry OBJECT-TYPE SYNTAX Dot3OmpEmulationStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table entries for Table of statistics counters of [802.3ah] clause 65 OMP interface." INDEX { ifIndex } ::= { dot3OmpEmulationStatTable 1 } Dot3OmpEmulationStatEntry::= SEQUENCE { dot3OmpEmulationSLDErrors Counter32, dot3OmpEmulationCRC8Errors Counter32, dot3OmpEmulationBadLLID Counter32, dot3OmpEmulationGoodLLID Counter32, dot3OmpEmulationOnuPonCastLLID Counter32, dot3OmpEmulationOltPonCastLLID Counter32, dot3OmpEmulationBroadcastLLIDNotOnuID Counter32, dot3OmpEmulationOnuLLIDNotBroadcast Counter32, dot3OmpEmulationBroadcastLLIDPlusOnuId Counter32, dot3OmpEmulationNotBroadcastLLIDNotOnuId Counter32 } dot3OmpEmulationSLDErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that do not contain a valid SLD field as defined in [802.3ah] clause 65.1.3.3.1. This attribute is mandatory for a OLT and optional for a ONU." REFERENCE "[802.3ah], 30.3.7.1.3." ::= { dot3OmpEmulationStatEntry 1} dot3OmpEmulationCRC8Errors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION EPON MIB WG Expires October 2004 [Page 21] Internet-Draft EPON MIBs April 29, 2004 "A count of frames received that contain a valid SLD field, as defined in [802.3ah] clause 65.1.3.3.1, but do not pass the CRC-8 check as defined in [802.3ah] clause 65.1.3.3.3. This attribute is mandatory for a OLT and optional for a ONU." REFERENCE "[802.3ah], 30.3.7.1.4." ::= { dot3OmpEmulationStatEntry 2} dot3OmpEmulationBadLLID OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of frames received that contain a valid SLD field in a OLT, as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check, as defined in [802.3ah] clause 65.1.3.3.3, but are discarded due to the LLID check as defined in [802.3ah] clause 65.1.3.3.2." REFERENCE "[802.3ah], 30.3.7.1.8." ::= { dot3OmpEmulationStatEntry 3} dot3OmpEmulationGoodLLID OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of frames received that contain a valid SLD field in a OLT, as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check, as defined in [802.3ah] clause 65.1.3.3.3" REFERENCE "[802.3ah], 30.3.7.1.5." ::= { dot3OmpEmulationStatEntry 4} dot3OmpEmulationOnuPonCastLLID OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that contain a valid SLD field in an ONU, as defined in [802.3ah] 65.1.3.3.1, passes the CRC-8 check, as defined in [802.3ah] 65.1.3.3.3, and the frame meets the rule for acceptance defined in [802.3ah] 65.1.3.3.2." REFERENCE "[802.3ah], 30.3.7.1.6." ::= { dot3OmpEmulationStatEntry 5} dot3OmpEmulationOltPonCastLLID OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only EPON MIB WG Expires October 2004 [Page 22] Internet-Draft EPON MIBs April 29, 2004 STATUS current DESCRIPTION "A count of frames received that contain a valid SLD field in an OLT, as defined in [802.3ah] 65.1.3.3.1, passes the CRC-8 check, as defined in [802.3ah] 65.1.3.3.3, and the frame meets the rule for acceptance defined in [802.3ah] 65.1.3.3.2." REFERENCE "[802.3ah], 30.3.7.1.7." ::= { dot3OmpEmulationStatEntry 6} dot3OmpEmulationBroadcastLLIDNotOnuID OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that contain a valid SLD field in a OLT, as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check, as defined in [802.3ah] clause 65.1.3.3.3, and contain broadcast LLID as defined in [802.3ah] clause 65. This attribute is mandatory for a OLT and for a ONU." ::= { dot3OmpEmulationStatEntry 7} dot3OmpEmulationOnuLLIDNotBroadcast OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that contain a valid SLD field in a OLT, as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check, as defined in [802.3ah] clause 65.1.3.3.3, and contain the ONUÆs LLID as defined in [802.3ah] clause 65. This attribute is mandatory for an ONU and mandatory for a OLT (a counter per LLID)." ::= { dot3OmpEmulationStatEntry 8} dot3OmpEmulationBroadcastLLIDPlusOnuId OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that contain a valid SLD field in a OLT, as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check, as defined in [802.3ah] clause 65.1.3.3.3, and contain the broadcast LLID plus ONUÆs LLID (frame reflected) as defined in [802.3ah] clause 65. This attribute is mandatory for an ONU and mandatory for a OLT (a counter per LLID)." ::= { dot3OmpEmulationStatEntry 9} EPON MIB WG Expires October 2004 [Page 23] Internet-Draft EPON MIBs April 29, 2004 dot3OmpEmulationNotBroadcastLLIDNotOnuId OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of frames received that contain a valid SLD field in a OLT, as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check, as defined in [802.3ah] clause 65.1.3.3.3, and does not contain the ONUÆs LLID as defined in [802.3ah] clause 65. This attribute is mandatory for an ONU" ::= { dot3OmpEmulationStatEntry 10} -- Conformance Statements -- Conformance Groups dot3OmpeGroups OBJECT IDENTIFIER ::={ dot3OmpeConformance 1} dot3OmpeGroupID OBJECT-GROUP OBJECTS { dot3OmpEmulationID, dot3OmpEmulationType } STATUS current DESCRIPTION "A collection of objects of dot3 OMP emulation ID entity state definition." ::= { dot3OmpeGroups 1 } dot3OmpeGroupStat OBJECT-GROUP OBJECTS { dot3OmpEmulationSLDErrors, dot3OmpEmulationCRC8Errors, dot3OmpEmulationBadLLID, dot3OmpEmulationGoodLLID, dot3OmpEmulationOnuPonCastLLID, dot3OmpEmulationOltPonCastLLID, dot3OmpEmulationBroadcastLLIDNotOnuID, dot3OmpEmulationOnuLLIDNotBroadcast, EPON MIB WG Expires October 2004 [Page 24] Internet-Draft EPON MIBs April 29, 2004 dot3OmpEmulationBroadcastLLIDPlusOnuId, dot3OmpEmulationNotBroadcastLLIDNotOnuId } STATUS current DESCRIPTION "A collection of objects of dot3 OMP emulation Statistics" ::= { dot3OmpeGroups 2 } -- Compliance dot3OmpeCompliances OBJECT IDENTIFIER ::= { dot3OmpeConformance 2 } dot3OmpeCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for OMPEmulation interfaces." MODULE -- this module MANDATORY-GROUPS { dot3OmpeGroupID} GROUP dot3OmpeGroupStat DESCRIPTION " This group is mandatory for all OMPemulation supporting interfaces for Statistics collection." ::= { dot3OmpeCompliances 1} -- EditorÆs note: MAU managed object definitions (30.5.1) dot3EponMauMIB OBJECT IDENTIFIER ::= { dot3EfmeponMIB 3} dot3EponMauObjects OBJECT IDENTIFIER ::= { dot3EponMauMIB 1} dot3EponMauConformance OBJECT IDENTIFIER ::= { dot3EponMauMIB 2 } dot3EponMauTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3EponMauEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for dot3 MAU EPON MIBs." ::= { dot3EponMauObjects 1 } EPON MIB WG Expires October 2004 [Page 25] Internet-Draft EPON MIBs April 29, 2004 dot3EponMauEntry OBJECT-TYPE SYNTAX Dot3EponMauEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the dot3 MAU EPON MIBs table." INDEX { ifIndex } ::= { dot3EponMauTable 1 } Dot3EponMauEntry ::= SEQUENCE { dot3EponMauPCSCodingViolation Counter32, dot3EponMauFecAbility INTEGER, dot3EponMauFecMode INTEGER, dot3EponMauFECCorrectedBlocks Counter32, dot3EponMauFECUncorrectableBlocks Counter32, dot3EponMauBufferHeadCodingViolation Counter32 } dot3EponMauPCSCodingViolation OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " For 100 Mb/ s operation it is a count of the number of times an invalid code-group is received, other than the /H/ code-group. For 1000 Mb/ s operation it is a count of the number of times an invalid codegroup is received, other than the /V/ code-group." REFERENCE "[802.3ah], 30.5.1.1.12." ::= { dot3EponMauEntry 1} dot3EponMauFecAbility OBJECT-TYPE SYNTAX INTEGER { unknown (1), nonsupported (2), supported (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that indicates the support of operation of the 1000BASE-PX PHY optional FEC Sublayer for Forward error correction see [802.3ah] clause 65.2). æunknownÆ value is assigned in initializing, for non FEC support state EPON MIB WG Expires October 2004 [Page 26] Internet-Draft EPON MIBs April 29, 2004 or type not yet known. ænonsupportedÆ value is assigned when Sublayer is not support. æsupportedÆ value is assigned when Sublayer is supported." REFERENCE "[802.3ah], 30.5.1.1.13." ::= { dot3EponMauEntry 2} dot3EponMauFecMode OBJECT-TYPE SYNTAX INTEGER { unknown (1), disabled (2), enabled (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "A read-write value that indicates the mode of operation of the 1000BASE-PX PHY optional FEC Sublayer for Forward error correction see [802.3ah] clause 65.2). A GET operation returns the current mode of operation the PHY. A SET operation changes the mode of operation of the PHY to the indicated value. æunknownÆ value is assigned in initializing, for non FEC support state or type not yet known. ædisabledÆ value is assigned when Sublayer operating in disabled mode. æenabledÆ value is assigned when Sublayer operating in FEC mode." REFERENCE "[802.3ah], 30.5.1.1.14." ::= { dot3EponMauEntry 3} dot3EponMauFECCorrectedBlocks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " For 10PASS-TS, 2BASE-TL and 1000BASE-PX PHYs, a count of corrected FEC blocks. This counter will not increment for other PHY Types. Increment the counter by one for each received block that is corrected by the FEC function in the PHY." REFERENCE "[802.3ah], 30.5.1.1.15." ::= { dot3EponMauEntry 4} dot3EponMauFECUncorrectableBlocks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " For 10PASS-TS, 2BASE-TL and 1000BASE-PX PHYs, a count of uncorrectable FEC blocks. This counter will not increment for other PHY Types. EPON MIB WG Expires October 2004 [Page 27] Internet-Draft EPON MIBs April 29, 2004 Increment the counter by one for each FEC block that is determined to be uncorrectable by the FEC function in the PHY." REFERENCE "[802.3ah], 30.5.1.1.16." ::= { dot3EponMauEntry 5} dot3EponMauBufferHeadCodingViolation OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " For 1000 Mbps operation it is a counts of the number of invalid code- group received directly from the link." ::= { dot3EponMauEntry 6} -- Defining EPON MAU types --This section should be added to 802.3 MAU MIB RFC. dot3EponMauType OBJECT IDENTIFIER ::= { dot3EponMauMIB 3 } eponMauType1000BasePXOLT OBJECT-IDENTITY STATUS current DESCRIPTION "Multipoint MAC Control (per 802.3 section 64,65) OLT (master), unknown PMD" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { dot3EponMauType 1 } eponMauType1000BasePXONU OBJECT-IDENTITY STATUS current DESCRIPTION "Multipoint MAC Control (per 802.3 section 64,65),ONU (slave), unknown PMD" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { dot3EponMauType 2 } eponMauType1000BasePX10DOLT OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 10K link, downlink (per 802.3 section 60), OLT side" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { dot3EponMauType 3 } eponMauType1000BasePX10DONU OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 10K link, downlink (per 802.3 section 60), ONU side" EPON MIB WG Expires October 2004 [Page 28] Internet-Draft EPON MIBs April 29, 2004 REFERENCE "[802.3ah], 30.5.1.1.2." ::= { dot3EponMauType 4 } eponMauType1000BasePX10UOLT OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 10K link, uplink (per 802.3 section 60), OLT side" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { dot3EponMauType 5 } eponMauType1000BasePX10UONU OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 10K link, uplink (per 802.3 section 60), ONU side" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { dot3EponMauType 6 } eponMauType1000BasePX20DOLT OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 20K link, downlink (per 802.3 section 60), OLT side" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { dot3EponMauType 7 } eponMauType1000BasePX20DONU OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 20K link, downlink (per 802.3 section 60), ONU side" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { dot3EponMauType 8 } eponMauType1000BasePX20UOLT OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 20K link, uplink (per 802.3 section 60), OLT side" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { dot3EponMauType 9 } eponMauType1000BasePX20UONU OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 20K link, uplink (per 802.3 section 60), ONU side" EPON MIB WG Expires October 2004 [Page 29] Internet-Draft EPON MIBs April 29, 2004 REFERENCE "[802.3ah], 30.5.1.1.2." ::= { dot3EponMauType 10 } -- Conformance Statements -- Conformance Groups dot3EponMauGroups OBJECT IDENTIFIER ::={ dot3EponMauConformance 1} dot3EponMauGroupAll OBJECT-GROUP OBJECTS { dot3EponMauPCSCodingViolation } STATUS current DESCRIPTION "A collection of objects of dot3 MAU definition." ::= { dot3EponMauGroups 1 } dot3EponMauGroupFEC OBJECT-GROUP OBJECTS { dot3EponMauFecAbility, dot3EponMauFecMode, dot3EponMauFECCorrectedBlocks, dot3EponMauFECUncorrectableBlocks, dot3EponMauBufferHeadCodingViolation } STATUS current DESCRIPTION "A collection of objects of FEC group definition." ::= { dot3EponMauGroups 2 } -- Compliance dot3EponMauCompliances OBJECT IDENTIFIER ::= {dot3EponMauConformance 2} dot3EponMauCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for MAU EPON interfaces." MODULE -- this module MANDATORY-GROUPS { dot3EponMauGroupAll } GROUP dot3EponMauGroupFEC EPON MIB WG Expires October 2004 [Page 30] Internet-Draft EPON MIBs April 29, 2004 DESCRIPTION " This group is mandatory for all EPON MAU devices Supporting FEC functionality as for Definitions and BER Statistics collection." ::= { dot3EponMauCompliances 1} END EPON MIB WG Expires October 2004 [Page 31] Internet-Draft EPON MIBs April 29, 2004 5. Relationship table of the dot3EFM MIB objects to the IEEE802.3ah objects oMPCP managed object class (30.3.5) dot3EFM MIB object IEEE802.3ah object Reference dot3MpcpID aMPCPID 30.3.5.1.1 dot3MpcpAdminState aMPCPAdminState 30.3.5.1.2 dot3MpcpMode aMPCPMode 30.3.5.1.3 dot3MpcpLinkID aMPCPLinkID 30.3.5.1.4 dot3MpcpRemoteMACAddress aMPCPRemoteMACAddress 30.3.5.1.5 dot3MpcpRegistrationState aMPCPRegistrationState 30.3.5.1.6 dot3MpcpMACCtrlFramesTransmitted aMPCPMACCtrlFramesTransmitted30.3.5.1.7 dot3MpcpMACCtrlFramesReceived aMPCPMACCtrlFramesReceived 30.3.5.1.8 dot3MpcpTxGate aMPCPTxGate 30.3.5.1.9 dot3MpcpTxRegAck aMPCPTxRegAck 30.3.5.1.10 dot3MpcpTxRegister aMPCPTxRegister 30.3.5.1.11 dot3MpcpTxRegRequest aMPCPTxRegRequest 30.3.5.1.12 dot3MpcpTxReport aMPCPTxReport 30.3.5.1.13 dot3MpcpRxGate aMPCPRxGate 30.3.5.1.14 dot3MpcpRxRegAck aMPCPRxRegAck 30.3.5.1.15 dot3MpcpRxRegister aMPCPRxRegister 30.3.5.1.16 dot3MpcpRxRegRequest aMPCPRxRegRequest 30.3.5.1.17 dot3MpcpRxReport aMPCPRxReport 30.3.5.1.18 dot3MpcpTransmitElapsed aMPCPTransmitElapsed 30.3.5.1.19 dot3MpcpReceiveElapsed aMPCPReceiveElapsed 30.3.5.1.20 dot3MpcpRoundTripTime aMPCPRoundTripTime 30.3.5.1.21 dot3MpcpDiscoveryWindowsSent aMPCPDiscoveryWindowsSent 30.3.5.1.22 dot3MpcpDiscoveryTimeout aMPCPDiscoveryTimeout 30.3.5.1.23 dot3MpcpMaximumPendingGrants aMPCPMaximumPendingGrants 30.3.5.1.24 dot3MPCPAdminControl acMPCPAdminControl 30.3.5.2.1 dot3MpcpOnTime laserOnTime 64.3.5.1 dot3MpcpOffTime laserOffTime 64.3.5.1 dot3MpcpSyncTime SyncTime 64.3.3.2 dot3MpcpRxNotSupportedMPCP oOMPEmulation managed object class (30.3.7) dot3EFM MIB object IEEE802.3ah object Reference dot3OmpEmulationID aOMPEmulationID 30.3.7.1.1 dot3OmpEmulationType aOMPEmulationType 30.3.7.1.2 dot3OmpEmulationSLDErrors aSLDErrors 30.3.7.1.3 dot3OmpEmulationCRC8Errors aCRC8Errors 30.3.7.1.4 EPON MIB WG Expires October 2004 [Page 32] Internet-Draft EPON MIBs April 29, 2004 dot3OmpEmulationGoodLLID aGoodLLID 30.3.7.1.5 dot3OmpEmulationOnuPonCastLLID aONUPONcastLLID 30.3.7.1.6 dot3OmpEmulationOltPonCastLLID aOLTPONcastLLID 30.3.7.1.7 dot3OmpEmulationBadLLID aBadLLID 30.3.7.1.8 dot3OmpEmulationBroadcastLLIDNotOnuID dot3OmpEmulationOnuLLIDNotBroadcast dot3OmpEmulationBroadcastLLIDPlusOnuId dot3OmpEmulationNotBroadcastLLIDNotOnuId oMAU managed object class (30.5.1) dot3EFM MIB object IEEE802.3ah object Reference dot3EponMauType aMAUType 30.5.1.1.2 dot3EponMauPCSCodingViolation aPCSCodingViolation 30.5.1.1.12 dot3EponMauFecAbility aFECAbility 30.5.1.1.13 dot3EponMauFecMode aFECmode 30.5.1.1.14 dot3EponMauFECCorrectedBlocks aFECCorrectedBlocks 30.5.1.1.15 dot3EponMauFECUncorrectableBlocks aFECUncorrectableBlocks 30.5.1.1.16 dot3EponMauBufferHeadCodingViolation EPON MIB WG Expires October 2004 [Page 33] Internet-Draft EPON MIBs April 29, 2004 6. Definitions - The EPON Device MIB EPON-DEVICE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, mib-2, OBJECT-TYPE, Counter32, Unsigned32, Integer32, zeroDotZero FROM SNMPv2-SMI TruthValue, DateAndTime, RowStatus, MacAddress FROM SNMPv2-TC ifIndex FROM IF-MIB MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF SnmpAdminString FROM SNMP-FRAMEWORK-MIB ; eponDeviceMIB MODULE-IDENTITY LAST-UPDATED "200404290000Z" -- April 29, 2004 ORGANIZATION "IETF Ethernet Interfaces and Hub MIB Working Group" CONTACT-INFO "WG charter: http://www.ietf.org/html.charters/hubmib-charter.html Mailing Lists: General Discussion: hubmib@ietf.org To Subscribe: hubmib-request@ietf.org In Body: subscribe your_email_address Chair: Dan Romascanu Postal: Avaya Inc. Atidim Technology Park, Bldg. 3 Tel Aviv 61131 Israel Tel: +972-3-645-8414 E-mail: dromasca@avaya.com Editor: Lior Khermosh Postal: Passave Technologies Inc. Ackerstein Towers, Tower A, 6th floor, 9 Hamenofim St. Hertzliya Pituach 46725, ISRAEL P.O.Box 2089 Hertzliya Pituach 46120 Israel EPON MIB WG Expires October 2004 [Page 34] Internet-Draft EPON MIBs April 29, 2004 Tel: +972-9-9717600 Ext: 7181 E-mail: lior.khermosh@passave.com" DESCRIPTION "The objects in this MIB module are used to manage Ethernet Passive Optical Network (EPON) devices which are based on the Ethernet in the First Mile (EFM) PON as defined in IEEE Draft P802.3ah/D3.0 clause 60,64,65. The following reference is used throughout this MIB module: [802.3ah] refers to: IEEE Draft P802.3ah/D3.3: 'Draft amendment to - Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications - Media Access Control Parameters,Physical Layers and Management Parameters for subscriber access networks', 22 April 2004. Of particular interest are Clause 64(MPCP) 65(P2mP RS) and 60 (PON PMDs). Clause 30, 'Management', and Clause 45,'Management Data Input/Output (MDIO) Interface'. Copyright (C) The Internet Society (2003). This version of this MIB module is part of XXXX see the RFC itself for full legal notices." -- Editor's Note: Replace XXXX with the actual RFC number -- assigned by RFC Editor and remove this note REVISION "200404290000Z" -- April 29, 2004 DESCRIPTION "Initial version, published as RFC XXXX." ::= { mib-2 XXX } -- Editor's Note: Replace XXX with a real OID once it is -- assigned by IANA and remove this note. eponDeviceObjectMIB OBJECT IDENTIFIER ::= { eponDeviceMIB 1} eponDeviceObjects OBJECT IDENTIFIER ::= { eponDeviceObjectMIB 1} eponDeviceConformance OBJECT IDENTIFIER ::= { eponDeviceObjectMIB 2 } EPON MIB WG Expires October 2004 [Page 35] Internet-Draft EPON MIBs April 29, 2004 eponDeviceControlObjects OBJECT IDENTIFIER ::= { eponDeviceObjects 1} eponDeviceStatObjects OBJECT IDENTIFIER ::= { eponDeviceObjects 2} eponDeviceEventObjects OBJECT IDENTIFIER ::= { eponDeviceObjects 3} eponDeviceControlTable OBJECT-TYPE SYNTAX SEQUENCE OF EponDeviceControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for EPON device MIBs." ::= { eponDeviceControlObjects 1 } eponDeviceControlEntry OBJECT-TYPE SYNTAX EponDeviceControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the EPON device Control table." INDEX { ifIndex } ::= { eponDeviceControlTable 1 } EponDeviceControlEntry ::= SEQUENCE { eponDeviceObjectReset INTEGER, eponDeviceObjectModes INTEGER, eponDeviceSerialNumber SnmpAdminString, eponDeviceObjectFecEnabled INTEGER, eponDeviceObjectOamMode INTEGER, eponDeviceObjectDeviceReadyMode INTEGER, eponDeviceObjectPowerDown TruthValue, eponDeviceObjectNumberOfLLIDs INTEGER, eponDeviceObjectRemoteMACAddressLLIDTable MacAddress, eponDeviceObjectReportThreshold Integer32 } eponDeviceObjectReset OBJECT-TYPE SYNTAX INTEGER { running(1), reset(2) } MAX-ACCESS read-write EPON MIB WG Expires October 2004 [Page 36] Internet-Draft EPON MIBs April 29, 2004 STATUS current DESCRIPTION "This variable can be used to reset the EPON device. The interface may be unavailable while the reset occurs and data may be lost." ::= { eponDeviceControlEntry 1 } eponDeviceObjectModes OBJECT-TYPE SYNTAX INTEGER { olt(1), onu(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable defines the mode of the EPON device. When an olt it is an Optical Line Terminal device (server) and when an onu and Optical Network Unit device (client)" ::= { eponDeviceControlEntry 2 } eponDeviceSerialNumber OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The serial number of the manufacturer for this device." ::= { eponDeviceControlEntry 3 } eponDeviceObjectFecEnabled OBJECT-TYPE SYNTAX INTEGER { noFecEnabled (1), fecTxEnabled (2), fecRxEnabled (3), fecTxRxEnabled (4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable defines whether the EPON device uses FEC as defined in the [802.3ah] clause 65.2 for EPON. When fecTxEnabled the device supports the FEC transmission mode. When fecRxEnabled the device supports the FEC Receive mode. When fecTxRxEnabled the device supports the FEC transmission and receive mode." ::= { eponDeviceControlEntry 4 } eponDeviceObjectOamMode OBJECT-TYPE SYNTAX INTEGER { noOam (1), EPON MIB WG Expires October 2004 [Page 37] Internet-Draft EPON MIBs April 29, 2004 oamServer (2), oamclient (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable defines the Operation Administration and Maintenance (OAM) mode of an EPON device as defined by the [802.3ah] clause 57. When noOam the device does not supports the OAM mode. When oamServer the device supports the OAM mode as a server unit. When oamClient the device supports the OAM mode as a client unit." ::= { eponDeviceControlEntry 5 } eponDeviceObjectDeviceReadyMode OBJECT-TYPE SYNTAX INTEGER { notReady (1), inProcess (2), ready (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable defines the mode of an EPON device in initialization û ready for registration as defined by the [802.3ah] clause 64. When notReady the device is not ready for operation. When inProcess the device is in initialization process. When ready the device is ready for registration." ::= { eponDeviceControlEntry 6 } eponDeviceObjectPowerDown OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this variable to powerDown will cause Device to be entered into Power down mode where no registration is allowed and only receiving data from the link" ::= { eponDeviceControlEntry 7 } eponDeviceObjectNumberOfLLIDs OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-Only EPON MIB WG Expires October 2004 [Page 38] Internet-Draft EPON MIBs April 29, 2004 STATUS current DESCRIPTION "A read only variable which defines the number of registered LLIDs (as defined by the [802.3ah] clause 65) in a EPON network for an OLT. Initialization value is 0." ::= { eponDeviceControlEntry 8 } eponDeviceObjectReportThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "A set of 8 integers, for each LLID, that defines the threshold reporting for each Queue in the REPORT message, as defined in [802.3ah] 64. The value returned shall be in 2 octets increaments." ::= { eponDeviceControlEntry 9 } eponDeviceRemoteMACAddressLLIDTable OBJECT-TYPE SYNTAX SEQUENCE OF EponDeviceRemoteMACAddressLLIDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of read-only value that identifies the source_address and LLIDs parameter of the remote devices in the network. This Macaddress value, as defined in [802.3ah], 30.3.5.1.5, is updated on reception of a valid frame with (1) a destination Field equal to the reserved multicast address for MAC Control specified in [802.3ah] Annex 31A, (2) lengthOrType field value equal to the reserved Type for MAC Control as specified in [802.3ah] Annex 31A. (3) an MPCP subtype value equal to the subtype reserved for MPCP as specified in [802.3ah] Annex 31A, and an LLID as allocated by the OLT. The table is defined as Remote MAC address û LLID (RMadL)" ::= { eponDeviceControlObjects 2 } eponDeviceRemoteMACAddressLLIDEntry OBJECT-TYPE SYNTAX EponDeviceRemoteMACAddressLLIDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A group of entries. Applications create and delete entries using eponDeviceRMadlEntryStatus. When adding objects to a notification they are added in the lexical order of their index in this table." INDEX {eponDeviceRMadlLogName, eponDeviceRMadlLLID } ::= { eponDeviceRemoteMACAddressLLIDTable 1 } EponDeviceRemoteMACAddressLLIDEntry ::= SEQUENCE { eponDeviceRMadlLogName SnmpAdminString, EPON MIB WG Expires October 2004 [Page 39] Internet-Draft EPON MIBs April 29, 2004 eponDeviceRMadlLLID Unsigned32, eponDeviceRMadlLogID OBJECT IDENTIFIER, eponDeviceRMadlRemoteMACAddress MacAddress, eponDeviceRMadlType INTEGER, eponDeviceRMadlAction INTEGER, eponDeviceRMadlEntryStatus RowStatus } eponDeviceRMadlLogName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A locally-unique, administratively assigned name for a group of entries." ::= { eponDeviceRemoteMACAddressLLIDEntry 1 } eponDeviceRMadlLLID OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "An arbitrary integer for the purpose of identifying the LLID." ::= { eponDeviceRemoteMACAddressLLIDEntry 2 } eponDeviceRMadlLogID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The object identifier of a MIB object to add to an entry." DEFVAL { zeroDotZero } ::= { eponDeviceRemoteMACAddressLLIDEntry 3 } eponDeviceRMadlRemoteMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The remote MAC address of the LLID." ::= { eponDeviceRemoteMACAddressLLIDEntry 4 } eponDeviceRMadlType OBJECT-TYPE SYNTAX INTEGER { EPON MIB WG Expires October 2004 [Page 40] Internet-Draft EPON MIBs April 29, 2004 registered (1), notRegister (2), } MAX-ACCESS read-write STATUS current DESCRIPTION "A list of types for entries." ::= { eponDeviceRemoteMACAddressLLIDEntry 5 } eponDeviceRMadlAction OBJECT-TYPE SYNTAX INTEGER { register (1), deregister (2), reregister (3 } MAX-ACCESS read-write STATUS current DESCRIPTION "A list of actions for an entry." ::= { eponDeviceRemoteMACAddressLLIDEntry 6 } eponDeviceRMadlEntryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The control that allows creation and deletion of entries. Once made active an entry MAY not be modified except to delete it." ::= { eponDeviceRemoteMACAddressLLIDEntry 7 } --Statistics tables eponDeviceStatTable OBJECT-TYPE SYNTAX SEQUENCE OF EponDeviceStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines the list of statistics counters of EPON devices." ::= { eponDeviceStatObjects 1} EPON MIB WG Expires October 2004 [Page 41] Internet-Draft EPON MIBs April 29, 2004 eponDeviceStatEntry OBJECT-TYPE SYNTAX EponDeviceStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table entries for Table of statistics counters of EPON devices." INDEX { ifIndex } ::= { eponDeviceStatTable 1 } EponDeviceStatEntry::= SEQUENCE { eponDeviceStatTxFramesQueue0 Counter32, eponDeviceStatTxFramesQueue1 Counter32, eponDeviceStatTxFramesQueue2 Counter32, eponDeviceStatTxFramesQueue3 Counter32, eponDeviceStatTxFramesQueue4 Counter32, eponDeviceStatTxFramesQueue5 Counter32, eponDeviceStatTxFramesQueue6 Counter32, eponDeviceStatTxFramesQueue7 Counter32, eponDeviceStatRxFramesQueue0 Counter32, eponDeviceStatRxFramesQueue1 Counter32, eponDeviceStatRxFramesQueue2 Counter32, eponDeviceStatRxFramesQueue3 Counter32, eponDeviceStatRxFramesQueue4 Counter32, eponDeviceStatRxFramesQueue5 Counter32, eponDeviceStatRxFramesQueue6 Counter32, eponDeviceStatRxFramesQueue7 Counter32, eponDeviceStatDroppedFramesQueue0 Counter32, eponDeviceStatDroppedFramesQueue1 Counter32, eponDeviceStatDroppedFramesQueue2 Counter32, eponDeviceStatDroppedFramesQueue3 Counter32, eponDeviceStatDroppedFramesQueue4 Counter32, eponDeviceStatDroppedFramesQueue5 Counter32, eponDeviceStatDroppedFramesQueue6 Counter32, eponDeviceStatDroppedFramesQueue7 Counter32 } eponDeviceStatTxFramesQueue0 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-0Æ frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of æQueue-0Æ. The æQueue-0Æ marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter EPON MIB WG Expires October 2004 [Page 42] Internet-Draft EPON MIBs April 29, 2004 is mandatory for an ONU." ::= { eponDeviceStatEntry 1} eponDeviceStatTxFramesQueue1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-1Æ frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of æQueue-1Æ. The æQueue-1Æ marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 2} eponDeviceStatTxFramesQueue2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-2Æ frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of æQueue-2Æ. The æQueue-2Æ marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 3} eponDeviceStatTxFramesQueue3 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-3Æ frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of æQueue-3Æ. The æQueue-3Æ marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 4} eponDeviceStatTxFramesQueue4 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-4Æ frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of æQueue-4Æ. The æQueue-4Æ marking matched the REPORT MPCP EPON MIB WG Expires October 2004 [Page 43] Internet-Draft EPON MIBs April 29, 2004 message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 5} eponDeviceStatTxFramesQueue5 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-5Æ frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of æQueue-5Æ. The æQueue-5Æ marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 6} eponDeviceStatTxFramesQueue6 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-6Æ frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of æQueue-6Æ. The æQueue-6Æ marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 7} eponDeviceStatTxFramesQueue7 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-7Æ frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of æQueue-7Æ. The æQueue-7Æ marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 8} eponDeviceStatRxFramesQueue0 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-0Æ frames reception occurs. A EPON MIB WG Expires October 2004 [Page 44] Internet-Draft EPON MIBs April 29, 2004 single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of æQueue-0Æ. The æQueue-0Æ marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { eponDeviceStatEntry 9} eponDeviceStatRxFramesQueue1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a æQueue-1Æ frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of æQueue-1Æ. The æQueue-1Æ marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { eponDeviceStatEntry 10} eponDeviceStatRxFramesQueue2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-2Æ frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of æQueue-2Æ. The æQueue-2Æ marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { eponDeviceStatEntry 11} eponDeviceStatRxFramesQueue3 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-3Æ frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of æQueue-3Æ. The æQueue-3Æ marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { eponDeviceStatEntry 12} eponDeviceStatRxFramesQueue4 OBJECT-TYPE EPON MIB WG Expires October 2004 [Page 45] Internet-Draft EPON MIBs April 29, 2004 SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a æQueue-4Æ frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of æQueue-4Æ. The æQueue-4Æ marking matched the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { eponDeviceStatEntry 13} eponDeviceStatRxFramesQueue5 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-5Æ frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of æQueue-5Æ. The æQueue-5Æ marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { eponDeviceStatEntry 14} eponDeviceStatRxFramesQueue6 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-6Æ frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of æQueue-6Æ. The æQueue-6Æ marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { eponDeviceStatEntry 15} eponDeviceStatRxFramesQueue7 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-7Æ frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of æQueue-7Æ. The æQueue-7Æ marking matched the EPON MIB WG Expires October 2004 [Page 46] Internet-Draft EPON MIBs April 29, 2004 REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT." ::= { eponDeviceStatEntry 16} eponDeviceStatDroppedFramesQueue0 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-0Æ frames drops occurs. Increment the counter by one for each frame dropped from æQueue-0Æ. The æQueue-0Æ marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 17} eponDeviceStatDroppedFramesQueue1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-1Æ frames drops occurs. Increment the counter by one for each frame dropped from æQueue-1Æ. The æQueue-1Æ marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 18} eponDeviceStatDroppedFramesQueue2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-2Æ frames drops occurs. Increment the counter by one for each frame dropped from æQueue-2Æ. The æQueue-2Æ marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 19} eponDeviceStatDroppedFramesQueue3 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-3Æ frames drops occurs. Increment the counter by one for each frame dropped from æQueue-3Æ. The æQueue-3Æ marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 20} EPON MIB WG Expires October 2004 [Page 47] Internet-Draft EPON MIBs April 29, 2004 eponDeviceStatDroppedFramesQueue4 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-4Æ frames drops occurs. Increment the counter by one for each frame dropped from æQueue-4Æ. The æQueue-4Æ marking matched the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 21} eponDeviceStatDroppedFramesQueue5 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-5Æ frames drops occurs. Increment the counter by one for each frame dropped from æQueue-5Æ. The æQueue-5Æ marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 22} eponDeviceStatDroppedFramesQueue6 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-6Æ frames drops occurs. Increment the counter by one for each frame dropped from æQueue-6Æ. The æQueue-6Æ marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 23} eponDeviceStatDroppedFramesQueue7 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION " A count of the number of times a æQueue-7Æ frames drops occurs. Increment the counter by one for each frame dropped from æQueue-7Æ. The æQueue-7Æ marking matched the REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU." ::= { eponDeviceStatEntry 24} EPON MIB WG Expires October 2004 [Page 48] Internet-Draft EPON MIBs April 29, 2004 --Editor's Note use reference to event MIBs [RFC2981] and --docsis MIBs [RFC2669] eponDeviceEventObjectTable OBJECT-TYPE SYNTAX SEQUENCE OF EponDeviceEventObjectEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines the list of statistics counters of EPON devices." ::= { eponDeviceEventObjects 1} eponDeviceEventObjectEntry OBJECT-TYPE SYNTAX EponDeviceEventObjectEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table entries for Table of Event objects for EPON devices." INDEX { ifIndex } ::= { eponDeviceEventObjectTable 1 } EponDeviceEventObjectEntry::= SEQUENCE { eponDeviceSampleMinimum Integer32, eponDeviceDyingGaspAlarmState TruthValue, eponDeviceDyingGaspAlarmEnabled TruthValue, eponDeviceCriticalEventState TruthValue, eponDeviceCriticalEventEnabled TruthValue, eponDeviceLocalLinkFaultAlarmState TruthValue, eponDeviceLocalLinkFaultAlarmEnabled TruthValue, eponDeviceTemperatureEventIndicationState TruthValue, eponDeviceTemperatureEventIndicationEnabled TruthValue, eponDevicePowerVoltageEventIndicationState TruthValue, eponDevicePowerVoltageEventIndicationEnabled TruthValue, eponDeviceGlobalEventState TruthValue, eponDeviceGlobalEventEnabled TruthValue, eponDeviceErroredSymbolPeriodEventState TruthValue, eponDeviceErroredSymbolPeriodEventEnabled TruthValue, eponDeviceErroredFrameEventState TruthValue, eponDeviceErroredFrameEventEnabled TruthValue, eponDeviceErroredFramePeriodEventState TruthValue, eponDeviceErroredFramePeriodEventEnabled TruthValue, eponDeviceErroredFrameSecondsSummaryEventState TruthValue, eponDeviceErroredFrameSecondsSummaryEventEnabled TruthValue, eponDeviceOrganizationSpecificEventState TruthValue, EPON MIB WG Expires October 2004 [Page 49] Internet-Draft EPON MIBs April 29, 2004 eponDeviceOrganizationSpecificEventEnabled TruthValue, eponDeviceEventControl INTEGER } eponDeviceSampleMinimum OBJECT-TYPE SYNTAX Integer32 (1..2147483647) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The minimum Frequency of events this system will accept. A system may use the larger values of this minimum to lessen the impact of constant sampling. For larger sampling intervals the system samples less often and suffers less overhead. Unless explicitly resource limited, a system's value for this object SHOULD be 1, allowing as small as a 1 second interval for ongoing trigger sampling." ::= { eponDeviceEventObjectEntry 1 } eponDeviceDyingGaspAlarmState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Dying Gasp indication of the OAM alarm indications as described in the [802.3ah] clause 57. When dyingGaspAlarm the device has a dying gasp alarm asserted. When the dyingGaspAlarm state is removed the dying gasp alarm is reset " ::= { eponDeviceEventObjectEntry 2} eponDeviceDyingGaspAlarmEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow DyingGaspAlarm event to be used. When the value is 'false' the event is not sampled." EPON MIB WG Expires October 2004 [Page 50] Internet-Draft EPON MIBs April 29, 2004 DEFVAL { false } ::= { eponDeviceEventObjectEntry 3 } eponDeviceCriticalEventState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Critical Event indication of the OAM alarm indications as described in the [802.3ah] clause 57. When criticalEvent the device has a Critical Event asserted. " ::= { eponDeviceEventObjectEntry 4 } eponDeviceCriticalEventEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow CriticalEvent event to be used. When the value is 'false' the event is not sampled." DEFVAL { false } ::= { eponDeviceEventObjectEntry 5 } eponDeviceLocalLinkFaultAlarmState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Local Link Fault indication of the OAM alarm indications as described in the [802.3ah] clause 57. When localLinkFaultAlarm the device has a Local Link Fault alarm asserted. " ::= { eponDeviceEventObjectEntry 6 } eponDeviceLocalLinkFaultAlarmEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow LocalLinkFaultAlarm event to be used. When the value is 'false' the event is not sampled." DEFVAL { false } ::= { eponDeviceEventObjectEntry 7 } eponDeviceTemperatureEventIndicationState OBJECT-TYPE EPON MIB WG Expires October 2004 [Page 51] Internet-Draft EPON MIBs April 29, 2004 SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Temperature Event indication of an EPON device. When condition of box temperature is above the threshold defined the alarm is asserted. When the condition is below that threshold the alarm is de-asserted. When temperatureEventIndication the device has a Temperature Event Indication asserted. " ::= { eponDeviceEventObjectEntry 8 } eponDeviceTemperatureEventIndicationEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow TemperatureEventIndication event to be used. When the value is 'false' the event is not sampled." DEFVAL { false } ::= { eponDeviceEventObjectEntry 9 } eponDevicePowerVoltageEventIndicationState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Power/Voltage Event Indication of an EPON device. When condition of box Power/voltage is above the threshold defined the alarm is asserted. When the condition is below that threshold the alarm is de- asserted. When powerVoltageEventIndication the device has a Power/Voltage Event Indication asserted. " ::= { eponDeviceEventObjectEntry 10 } eponDevicePowerVoltageEventIndicationEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow PowerVoltageEventIndication event to be used. When the value is 'false' the event is not sampled." EPON MIB WG Expires October 2004 [Page 52] Internet-Draft EPON MIBs April 29, 2004 DEFVAL { false } ::= { eponDeviceEventObjectEntry 11 } eponDeviceGlobalEventState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Global Event indication of an EPON device. When the indication of the event input occurs the event is asserted. When the input is removed that event is de-asserted. When globalEvent the device has a Global Event asserted. " ::= { eponDeviceEventObjectEntry 12 } eponDeviceGlobalEventEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow GlobalEvent event to be used. When the value is 'false' the event is not sampled." DEFVAL { false } ::= { eponDeviceEventObjectEntry 13 } eponDeviceErroredSymbolPeriodEventState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Errored Symbol Period Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When erroredSymbolPeriodEvent the device has an Errored Symbol Period Event asserted. " ::= { eponDeviceEventObjectEntry 14} eponDeviceErroredSymbolPeriodEventEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow ErroredSymbolPeriodEvent event to be used. When the value is 'false' the event is not sampled." DEFVAL { false } ::= { eponDeviceEventObjectEntry 15 } EPON MIB WG Expires October 2004 [Page 53] Internet-Draft EPON MIBs April 29, 2004 eponDeviceErroredFrameEventState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Errored Frame Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When erroredFrameEvent the device has an Errored Frame Event asserted. " ::= { eponDeviceEventObjectEntry 16 } eponDeviceErroredFrameEventEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow ErroredFrameEvent event to be used. When the value is 'false' the event is not sampled." DEFVAL { false } ::= { eponDeviceEventObjectEntry 17 } eponDeviceErroredFramePeriodEventState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Errored Frame Period Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When erroredFramePeriodEvent the device has an Errored Frame Period Event asserted. " ::= { eponDeviceEventObjectEntry 18 } eponDeviceErroredFramePeriodEventEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow ErroredFramePeriodEvent event to be used. When the value is 'false' the event is not sampled." DEFVAL { false } ::= { eponDeviceEventObjectEntry 19 } eponDeviceErroredFrameSecondsSummaryEventState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only EPON MIB WG Expires October 2004 [Page 54] Internet-Draft EPON MIBs April 29, 2004 STATUS current DESCRIPTION "A read-only variable, which defines the state of the Errored Frame Seconds Summary Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When erroredFrameSecondsSummaryEvent the device has an Errored Frame Seconds Summary Event asserted. " ::= { eponDeviceEventObjectEntry 20 } eponDeviceErroredFrameSecondsSummaryEventEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow ErroredFrameSecondsSummaryEvent event to be used. When the value is 'false' the event is not sampled." DEFVAL { false } ::= { eponDeviceEventObjectEntry 21 } eponDeviceOrganizationSpecificEventState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable, which defines the state of the Organization Specific Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When organizationSpecificEvent the device has an Organization Specific Event asserted. " ::= { eponDeviceEventObjectEntry 22 } eponDeviceOrganizationSpecificEventEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A control to allow OrganizationSpecificEvent event to be used. When the value is 'false' the event is not sampled." DEFVAL { false } ::= { eponDeviceEventObjectEntry 23 } eponDeviceEventControl OBJECT-TYPE SYNTAX INTEGER { EPON MIB WG Expires October 2004 [Page 55] Internet-Draft EPON MIBs April 29, 2004 resetLog(1), useDefaultReporting(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to resetLog(1) empties the event log. All data is deleted. Setting it to useDefaultReporting(2) returns all event priorities to their factory-default reporting. Reading this object always returns useDefaultReporting(2)." ::= { eponDeviceEventObjectEntry 24 } -- Events Log Table eponDeviceEventsLogTable OBJECT-TYPE SYNTAX SEQUENCE OF EponDeviceEventsLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of objects that can be added to notifications based on the event as pointed to by entries in those tables." ::= { eponDeviceEventObjects 2 } eponDeviceEventsLogEntry OBJECT-TYPE SYNTAX EponDeviceEventsLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A group of Events. Applications create and delete entries using eponDeviceEventsEntryStatus. When adding objects to a notification they are added in the lexical order of their index in this table." INDEX {eponDeviceEventsLogName, eponDeviceEventsLogIndex } ::= { eponDeviceEventsLogTable 1 } EponDeviceEventsLogEntry ::= SEQUENCE { eponDeviceEventsLogName SnmpAdminString, eponDeviceEventsLogIndex Unsigned32, eponDeviceEventsLogID OBJECT IDENTIFIER, eponDeviceEventsLogFirstTime DateAndTime, eponDeviceEventsLogLastTime DateAndTime, eponDeviceEventsLogCounts Counter32, EPON MIB WG Expires October 2004 [Page 56] Internet-Draft EPON MIBs April 29, 2004 eponDeviceEventsLogType INTEGER, eponDeviceEventsLogEntryStatus RowStatus } eponDeviceEventsLogName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A locally-unique, administratively assigned name for a group of Events." ::= { eponDeviceEventsLogEntry 1 } eponDeviceEventsLogIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer for the purpose of identifying individual Events within a eponDeviceEventsLogName group. Events within a group are placed in the notification in the numerical order of this index." ::= { eponDeviceEventsLogEntry 2 } eponDeviceEventsLogID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The object identifier of a MIB object to add to a Notification that results from the event." DEFVAL { zeroDotZero } ::= { eponDeviceEventsLogEntry 3 } eponDeviceEventsLogFirstTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time that an entry was created." ::= { eponDeviceEventsLogEntry 4 } eponDeviceEventsLogLastTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "If multiple events are reported via the same entry, the EPON MIB WG Expires October 2004 [Page 57] Internet-Draft EPON MIBs April 29, 2004 time that the last event for this entry occurred, otherwise this should have the same value as eponDeviceEventsLogFirstTime. " ::= { eponDeviceEventsLogEntry 5 } eponDeviceEventsLogCounts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of consecutive event instances reported by this entry. This starts at 1 with the creation of this row and increments by 1 for each subsequent duplicate event." ::= { eponDeviceEventsLogEntry 6 } eponDeviceEventsLogType OBJECT-TYPE SYNTAX INTEGER { eponDeviceDyingGaspAlarmState (1), eponDeviceCriticalEventState (2), eponDeviceLocalLinkFaultAlarmState (3), eponDeviceTemperatureEventIndicationState (4), eponDevicePowerVoltageEventIndicationState (5), eponDeviceGlobalEventState (6), eponDeviceErroredSymbolPeriodEventState (7), eponDeviceErroredFrameEventState (8), eponDeviceErroredFramePeriodEventState (9), eponDeviceErroredFrameSecondsSummaryEventState (10), eponDeviceOrganizationSpecificEventState (11) } MAX-ACCESS read-only STATUS current DESCRIPTION "A list of types for Events." ::= { eponDeviceEventsLogEntry 7 } eponDeviceEventsLogEntryStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The control that allows creation and deletion of entries. Once made active an entry MAY not be modified except to EPON MIB WG Expires October 2004 [Page 58] Internet-Draft EPON MIBs April 29, 2004 delete it." ::= { eponDeviceEventsLogEntry 8 } -- Conformance Statements -- Conformance Groups eponDeviceGroups OBJECT IDENTIFIER ::={ eponDeviceConformance 1} eponDeviceGroupControl OBJECT-GROUP OBJECTS { eponDeviceObjectReset, eponDeviceObjectModes, eponDeviceSerialNumber, eponDeviceObjectFecEnabled, eponDeviceObjectOamMode, eponDeviceObjectDeviceReadyMode, eponDeviceObjectPowerDown, eponDeviceObjectNumberOfLLIDs, eponDeviceObjectRemoteMACAddressLLIDTable, eponDeviceObjectReportThreshold } STATUS current DESCRIPTION "A collection of objects of eponDevice control definition." ::= { eponDeviceGroups 1 } eponDeviceGroupRMadLTable OBJECT-GROUP OBJECTS { eponDeviceRMadlLogName, eponDeviceRMadlLLID, eponDeviceRMadlLogID, eponDeviceRMadlRemoteMACAddress, eponDeviceRMadlType, eponDeviceRMadlAction, eponDeviceRMadlEntryStatus } STATUS current DESCRIPTION "A collection of objects of eponDevice remote Mac address EPON MIB WG Expires October 2004 [Page 59] Internet-Draft EPON MIBs April 29, 2004 to LLID table." ::= { eponDeviceGroups 2 } eponDeviceGroupStat OBJECT-GROUP OBJECTS { eponDeviceStatTxFramesQueue0, eponDeviceStatTxFramesQueue1, eponDeviceStatTxFramesQueue2, eponDeviceStatTxFramesQueue3, eponDeviceStatTxFramesQueue4, eponDeviceStatTxFramesQueue5, eponDeviceStatTxFramesQueue6, eponDeviceStatTxFramesQueue7, eponDeviceStatRxFramesQueue0, eponDeviceStatRxFramesQueue1, eponDeviceStatRxFramesQueue2, eponDeviceStatRxFramesQueue3, eponDeviceStatRxFramesQueue4, eponDeviceStatRxFramesQueue5, eponDeviceStatRxFramesQueue6, eponDeviceStatRxFramesQueue7, eponDeviceStatDroppedFramesQueue0, eponDeviceStatDroppedFramesQueue1, eponDeviceStatDroppedFramesQueue2, eponDeviceStatDroppedFramesQueue3, eponDeviceStatDroppedFramesQueue4, eponDeviceStatDroppedFramesQueue5, eponDeviceStatDroppedFramesQueue6, eponDeviceStatDroppedFramesQueue7 } STATUS current DESCRIPTION "A collection of objects of EPON device Statistics" ::= { eponDeviceGroups 3 } eponDeviceGroupEvent OBJECT-GROUP OBJECTS { eponDeviceSampleMinimum, eponDeviceDyingGaspAlarmState, eponDeviceDyingGaspAlarmEnabled, eponDeviceCriticalEventState, eponDeviceCriticalEventEnabled, eponDeviceLocalLinkFaultAlarmState, eponDeviceLocalLinkFaultAlarmEnabled, eponDeviceTemperatureEventIndicationState, eponDeviceTemperatureEventIndicationEnabled, EPON MIB WG Expires October 2004 [Page 60] Internet-Draft EPON MIBs April 29, 2004 eponDevicePowerVoltageEventIndicationState, eponDevicePowerVoltageEventIndicationEnabled, eponDeviceGlobalEventState, eponDeviceGlobalEventEnabled, eponDeviceErroredSymbolPeriodEventState, eponDeviceErroredSymbolPeriodEventEnabled, eponDeviceErroredFrameEventState, eponDeviceErroredFrameEventEnabled, eponDeviceErroredFramePeriodEventState , eponDeviceErroredFramePeriodEventEnabled , eponDeviceErroredFrameSecondsSummaryEventState , eponDeviceErroredFrameSecondsSummaryEventEnabled, eponDeviceOrganizationSpecificEventState , eponDeviceOrganizationSpecificEventEnabled, eponDeviceEventControl } STATUS current DESCRIPTION "A collection of objects for EPON device Events" ::= { eponDeviceGroups 4 } eponDeviceGroupEventLog OBJECT-GROUP OBJECTS { eponDeviceEventsLogID, eponDeviceEventsLogFirstTime, eponDeviceEventsLogLastTime, eponDeviceEventsLogCounts, eponDeviceEventsLogType, eponDeviceEventsLogEntryStatus } STATUS current DESCRIPTION "A collection of objects for EPON device Events log" ::= { eponDeviceGroups 5 } -- Compliance eponDeviceCompliances OBJECT IDENTIFIER ::= { eponDeviceConformance 2} eponDeviceCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for EPON Devices." EPON MIB WG Expires October 2004 [Page 61] Internet-Draft EPON MIBs April 29, 2004 MODULE -- this module MANDATORY-GROUPS { eponDeviceGroupControl } GROUP eponDeviceGroupRMadLTable DESCRIPTION " This group is mandatory for all EPON devices supporting LLID-MAC address table." GROUP eponDeviceGroupStat DESCRIPTION " This group is mandatory for all EPON devices supporting interfaces for Statistics collection." GROUP eponDeviceGroupEvent DESCRIPTION " This group is mandatory for all EPON devices supporting interfaces for event collection." GROUP eponDeviceGroupEventLog DESCRIPTION " This group is mandatory for all EPON devices supporting interfaces for event log collection." ::= { eponDeviceCompliances 1} END EPON MIB WG Expires October 2004 [Page 62] Internet-Draft EPON MIBs April 29, 2004 7. Security Considerations There are number of managed objects defined in this MIB module that have a MAX-ACCESS clause of read-write. Most objects are writeable only when the link is Down. Writing to these objects can have the following potentially disruptive effects on network operation: Including: Changing dot3MpcpMode mode Changing dot3MPCPAdminControl state Changing eponDeviceObjectReportThreshold Changing dot3EponMauFecMode mode Changing eponDeviceObjectReset mode Changing eponDeviceObjectFecEnabled mode Changing eponDeviceObjectOamMode mode Changing eponDeviceObjectDeviceReadyMode Changing eponDeviceObjectPowerDown Changing eponDeviceObjectReportThreshold Changing eponDeviceRMadlLogID Changing eponDeviceRMadlLLID Changing eponDeviceRMadlRemoteMacAddress Changing eponDeviceRMadlType Changing eponDeviceRMadlAction Changing eponDeviceRMadlEntryStatus Changing eponDeviceSampleMinimum Changing eponDeviceDyingGaspAlarmEnabled Changing eponDeviceCriticalEventEnabled Changing eponDeviceLocalLinkFaultAlarmEnabled Changing eponDeviceTemperatureEventIndicationEnabled Changing eponDevicePowerVoltageEventIndicationEnabled Changing eponDeviceGlobalEventEnabled Changing eponDeviceErroredSymbolPeriodEventEnabled Changing eponDeviceErroredFrameEventEnabled Changing eponDeviceErroredFramePeriodEventEnabled Changing eponDeviceErroredFrameSecondsSummaryEventEnabled Changing eponDeviceOrganizationSpecificEventEnabled Changing eponDeviceEventControl Changing eponDeviceEventsLogID Changing eponDeviceEventsLogEntryStatus The user of this MIB module must therefore be aware that support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. The readable objects in this MIB module (i.e., those with MAX-ACCESS other than not-accessible) may be considered sensitive in some environments since, collectively, they provide information about the performance of network interfaces and can reveal some aspects of their configuration. In such environments it is important to control EPON MIB WG Expires October 2004 [Page 63] Internet-Draft EPON MIBs April 29, 2004 even GET and NOTIFY access to these objects and possibly even to encrypt their values when sending them over the network via SNMP. SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPSec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module. It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC3410], section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy). Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 8. Intellectual Property The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found in BCP-11. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF Secretariat. EPON MIB WG Expires October 2004 [Page 64] Internet-Draft EPON MIBs April 29, 2004 9. Normative References [802.3] Institute of Electrical and Electronic Engineers, IEEE Std 802.3-2002, "IEEE Standard for Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications [802.3ah] Institute of Electrical and Electronic Engineers, IEEE Draft 802.3ah-2002 Draft 3.3, "IEEE Standard for Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications - Draft amendment to - Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications - Media Access Control Parameters, Physical Layers and Management Parameters for subscriber access networks [RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] McCloghrie, K., Perkins, D. and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [RFC3636] Flick, J., "Definitions of Managed Objects for IEEE 802.3 Medium Attachment Units (MAUs)", RFC 3636, September 2003. [RFC2665] Flick, J. and Johnson J. " Definitions of Managed Objects for the Ethernet-like Interface Types", STD 58, RFC 2580, April 1999. [draft-ietf-hubmibùefm-mib] Matt Squire "Generic EFM MIB", Internet draft, draft-ietf-hubmibùefm-mib-00.txt, December 2003 [RFC3591] H-K. Lam, M. Stewart, A. Huynh, "Definitions of Managed Objects for the Optical Interface Type.", RFC 3591, September 2003. [RFC2669] M. St. Johns, Ed., "DOCSIS Cable Device MIB Cable Device Management Information Base for DOCSIS compliant Cable Modems and Cable Modem Termination Systems.", RFC 2669, August 1999. [RFC2981] R. Kavasseri, "Event MIB.", RFC 2981, October 2000. EPON MIB WG Expires October 2004 [Page 65] Internet-Draft EPON MIBs April 29, 2004 [RFC1493] E. Decker, P. Langille, A. Rijsinghani, K. McCloghrie, "Definitions of Managed Objects for Bridges", RFC 1493, July 1993. [RFC1525]. E. Decker, K. McCloghrie, P. Langille, A. Rijsinghani, "Definitions of Managed Objects for Source Routing Bridges", RFC 1525, September 1993. 10. Informative References [RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000. [RFC2864] McCloghrie, K. and G. Hanson, "The Inverted Stack Table Extension to the Interfaces Group MIB", RFC 2864, June 2000. [RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart, "Introduction and Applicability Statements for Internet- Standard Management Framework", RFC 3410, December 2002. EPON MIB WG Expires October 2004 [Page 66] Internet-Draft EPON MIBs April 29, 2004 Copyright Notice Copyright (C) The Internet Society (2003). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AuthorÆs information Lior Khermosh Passave Technologies, Ackerstein Towers, Tower A, 6th floor, 9 Hamenofim St. Hertzliya Pituach 46725, ISRAEL P.O.Box 2089 Hertzliya Pituach 46120 Israel Tel: +972-9-9717600 Ext: 7181 Fax: +972-9-9540245 Mob: +972-55-224054 lior.khermosh@passave.com EPON MIB WG Expires October 2004 [Page 67]