IDR J. Snijders Internet-Draft Fastly Updates: 4271 (if approved) B. Cartwright-Cox Intended status: Standards Track Port 179 Expires: 7 February 2025 Y. Qu Futurewei 6 August 2024 Border Gateway Protocol 4 (BGP-4) Send Hold Timer draft-ietf-idr-bgp-sendholdtimer-15 Abstract This document defines the SendHoldtimer, along with the SendHoldTimer_Expires event, for the Border Gateway Protocol (BGP) Finite State Machine (FSM). Implementation of the SendHoldTimer helps overcome situations where a BGP connection is not terminated after the local system detects that the remote system is not processing BGP messages. This document specifies that the local system should close the BGP connection and not solely rely on the remote system for connection closure when the SendHoldTimer expires. This document updates RFC4271. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on 7 February 2025. Snijders, et al. Expires 7 February 2025 [Page 1] Internet-Draft BGP SendHoldTimer August 2024 Copyright Notice Copyright (c) 2024 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/ license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Example of a problematic scenario . . . . . . . . . . . . . . 3 3. Changes to RFC 4271 - SendHoldTimer . . . . . . . . . . . . . 4 3.1. Session Attributes . . . . . . . . . . . . . . . . . . . 4 3.2. Timer Event: SendHoldTimer_Expires . . . . . . . . . . . 4 3.3. Changes to the FSM . . . . . . . . . . . . . . . . . . . 4 3.4. Changes to BGP Timers . . . . . . . . . . . . . . . . . . 6 4. Send Hold Timer Expired Error Handling . . . . . . . . . . . 6 5. Implementation Considerations . . . . . . . . . . . . . . . . 6 6. Operational Considerations . . . . . . . . . . . . . . . . . 7 7. Security Considerations . . . . . . . . . . . . . . . . . . . 7 8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 7 9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 7 10. References . . . . . . . . . . . . . . . . . . . . . . . . . 7 10.1. Normative References . . . . . . . . . . . . . . . . . . 7 10.2. Informative References . . . . . . . . . . . . . . . . . 8 Appendix A. Implementation status - RFC EDITOR: REMOVE BEFORE PUBLICATION . . . . . . . . . . . . . . . . . . . . . . . 9 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 9 1. Introduction This document defines the SendHoldtimer, along with the SendHoldTimer_Expires event, for the Border Gateway Protocol (BGP) [RFC4271] Finite State Machine (FSM) defined in section 8. Snijders, et al. Expires 7 February 2025 [Page 2] Internet-Draft BGP SendHoldTimer August 2024 Failure to terminate a blocked BGP connection can result in network reachability issues, and the subsequent failure to generate and deliver BGP UPDATE messages to another BGP speaker of the local system is detrimental to all participants of the inter-domain routing system. This phenomena is thought to have contributed to IP traffic blackholing events in the global Internet routing system [bgpzombies]. This specification intends to improve this situation by requiring that BGP connections be terminated if the local system has detected that the remote system cannot possibly have processed any BGP messages for the duration of the SendHoldTime. Through standardization of the aforementioned requirement, operators will benefit from consistent behavior across different BGP implementations. BGP speakers following this specification do not rely exclusively on remote systems closing blocked connections, but will also locally close blocked connections. 2. Example of a problematic scenario In implementations lacking the concept of a SendHoldTimer, a malfunctioning or overwhelmed remote speaker may cause data on the BGP socket in the local system to accumulate ad infinitum. This could result in forwarding failure and traffic loss, as the overwhelmed speaker continues to utilize stale routes. An example fault state: as BGP runs over TCP [RFC9293], it is possible for a BGP speaker in the Established state to encounter a BGP speaker that is advertising a TCP Receive Window (RCV.WND) of size zero. This 0 window prevents the local system from sending KEEPALIVE, UPDATE, or any other critical BGP messages across the network socket to the remote speaker. Generally BGP implementations have no visibility into lower-layer subsystems such as TCP or the speaker's current Receive Window size, and there is no existing BGP mechanism for such a blocked connection to be recognized. Hence BGP implementations are not able to handle this situation in a consistent fashion. The major issue arising from a BGP speaker being unable to send a BGP message to a given remote speaker is that as a result that speaker subsequently is operating based on stale routing information. Failure of the BGP speaker to send (and thus the remote speaker to receive) BGP messages on a single BGP session can negatively impact the ability of an entire autonomous system (or even a group of autonomous systems) to converge. Snijders, et al. Expires 7 February 2025 [Page 3] Internet-Draft BGP SendHoldTimer August 2024 3. Changes to RFC 4271 - SendHoldTimer BGP speakers are implemented following a conceptual model "BGP Finite State Machine" (FSM), which is outlined in section 8 of [RFC4271]. This specification adds a BGP timer, SendHoldTimer, and updates the BGP FSM as follows: 3.1. Session Attributes The following optional session attributes for each connection are added to Section 8, before "The optional session attributes support different features of the BGP functionality that have implications for the BGP FSM state transitions": NEW | 14) SendHoldTimer | | 15) SendHoldTime The SendHoldTime determines how long a BGP speaker will stay in Established state before the TCP connection is dropped because no BGP messages can be transmitted to its peer. A BGP speaker can configure the value of the SendHoldTime for each peer independently. 3.2. Timer Event: SendHoldTimer_Expires Another timer event is added to Section 8.1.3 of [RFC4271] as following: NEW | Event 29: SendHoldTimer_Expires | Definition: An event generated when the SendHoldTimer expires. | | Status: Optional 3.3. Changes to the FSM The following changes are made to section 8.2.2 in [RFC4271]. In "OpenConfirm State", the handling of Event 26 is revised as follows: OLD | If the local system receives a KEEPALIVE message (KeepAliveMsg | (Event 26)), the local system: Snijders, et al. Expires 7 February 2025 [Page 4] Internet-Draft BGP SendHoldTimer August 2024 | - restarts the HoldTimer and | | - changes its state to Established. NEW | If the local system receives a KEEPALIVE message (KeepAliveMsg | (Event 26)), the local system: | - restarts the HoldTimer, | | - starts the SendHoldTimer if the SendHoldTime is non-zero, and | | - changes its state to Established. The following paragraph is added to section 8.2.2 in "Established State", after the paragraph which ends "unless the negotiated HoldTime value is zero.": NEW | If the SendHoldTimer_Expires (Event 29) occurs, the local | system: | | - (optionally) sends a NOTIFICATION message with the BGP Error | Code "Send Hold Timer Expired" if the local system can | determine that doing so will not delay the following actions | in this paragraph, | | - logs an error message in the local system with the BGP Error | Code "Send Hold Timer Expired", | | - releases all BGP resources, | | - sets the ConnectRetryTimer to zero, | | - drops the TCP connection, | | - increments the ConnectRetryCounter by 1, | | - (optionally) performs peer oscillation damping if the | DampPeerOscillations attribute is set to TRUE, and | | - changes its state to Idle. | | Each time the local system sends a BGP message, it restarts the | SendHoldTimer unless the SendHoldTime value is zero or the | negotiated HoldTime value is zero, in which cases the | SendHoldTimer is stopped. Snijders, et al. Expires 7 February 2025 [Page 5] Internet-Draft BGP SendHoldTimer August 2024 | | The SendHoldTimer is stopped following any transition out of | the Established state as part of the "release all BGP | resources" action. 3.4. Changes to BGP Timers Section 10 of [RFC4271] summarizes BGP Timers. This document adds another optional BGP timer: SendHoldTimer. NEW | SendHoldTime is an FSM attribute that stores the initial value for | the SendHoldTimer. If SendHoldTime is non-zero then it MUST be | greater than the value of HoldTime, see Section 5 of | [I-D.ietf-idr-bgp-sendholdtimer] for suggested default values. 4. Send Hold Timer Expired Error Handling If the local system does not send any BGP messages within the period specified in SendHoldTime, then a NOTIFICATION message with the "Send Hold Timer Expired" Error Code MAY be sent and the BGP connection MUST be closed. Additionally, an error MUST be logged in the local system, indicating the Send Hold Timer Expired Error Code. 5. Implementation Considerations Due to the relative rarity of the failure mode that this specification is designed to address, and also the fact that network operators may be unfamiliar with the formal specification of BGP fault detection mechanisms such as HoldTimer, it is likely that a large number of operators are unaware of the necessity of an additional mechanism such as SendHoldtimer. Accordingly, it is RECOMMENDED that implementations of this specification enable SendHoldtimer by default, without requiring additional configuration of the BGP speaking device. The default value of SendHoldTime for a BGP connection SHOULD be the greater of: * 8 minutes; or * 2 times the negotiated HoldTime Implementations MAY make the value of SendHoldTime configurable, either globally or on a per-peer basis, within the constraints set out in Section 3.4 above. Snijders, et al. Expires 7 February 2025 [Page 6] Internet-Draft BGP SendHoldTimer August 2024 The subcode for NOTIFICATION message "Send Hold Timer Expired" is set to 0 and is not used, no additional data is to be appended to the end of a "Send Hold Timer Expired" NOTIFICATION message. 6. Operational Considerations When the local system recognizes a remote speaker is not processing any BGP messages for the duration of the SendHoldTime, it is likely that the local system will not be able to inform the remote peer through a NOTIFICATION message as to why the connection is being closed. This documents suggests that an attempt to send a NOTIFICATION message with the "Send Hold Timer Expired" error code is still made, if doing so will not delay closing the BGP connection. Meanwhile an error message is logged into the local system. Other mechanisms can be used as well, for example BGP speakers SHOULD provide this reason as part of their operational state; e.g. bgpPeerLastError in the BGP MIB [RFC4273]. 7. Security Considerations This specification does not change BGP's security characteristics. Implementing the BGP SendHoldTimer as specified in this document will enhance network resilience by terminating connections with malfunctioning or overwhelmed remote peers. 8. IANA Considerations IANA has registered code 8 for "Send Hold Timer Expired" in the "BGP Error (Notification) Codes" registry in the "Border Gateway Protocol (BGP) Parameters" registry group. 9. Acknowledgements The authors would like to thank William McCall, Theo de Raadt, John Heasley, Nick Hilliard, Jeffrey Haas, Tom Petch, Susan Hares, Keyur Patel, Ben Maddison, Claudio Jeker, and John Scudder for their helpful review of this document. 10. References 10.1. Normative References Snijders, et al. Expires 7 February 2025 [Page 7] Internet-Draft BGP SendHoldTimer August 2024 [I-D.ietf-idr-bgp-sendholdtimer] Snijders, J., Cartwright-Cox, B., and Y. Qu, "Border Gateway Protocol 4 (BGP-4) Send Hold Timer", Work in Progress, Internet-Draft, draft-ietf-idr-bgp- sendholdtimer, . [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC4271] Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A Border Gateway Protocol 4 (BGP-4)", RFC 4271, DOI 10.17487/RFC4271, January 2006, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . [RFC9293] Eddy, W., Ed., "Transmission Control Protocol (TCP)", RFC 9293, DOI 10.17487/RFC9293, August 2022, . 10.2. Informative References [bgpzombies] Fontugne, R., "BGP Zombies", April 2019, . [BIRD] Kubecova, K., "BIRD Internet Routing Daemon", October 2023, . [frr] Lamparter, D., "bgpd: implement SendHoldTimer", May 2022, . [neo-bgp] Cartwright-Cox, B., "What does bgp.tools support", August 2022, . [openbgpd] Jeker, C., "bgpd send side hold timer", December 2020, . [RFC4273] Haas, J., Ed. and S. Hares, Ed., "Definitions of Managed Objects for BGP-4", RFC 4273, DOI 10.17487/RFC4273, January 2006, . Snijders, et al. Expires 7 February 2025 [Page 8] Internet-Draft BGP SendHoldTimer August 2024 Appendix A. Implementation status - RFC EDITOR: REMOVE BEFORE PUBLICATION This section records the status of known implementations of the protocol defined by this specification at the time of posting of this Internet-Draft, and is based on a proposal described in RFC 7942. The description of implementations in this section is intended to assist the IETF in its decision processes in progressing drafts to RFCs. Please note that the listing of any individual implementation here does not imply endorsement by the IETF. Furthermore, no effort has been spent to verify the information presented here that was supplied by IETF contributors. This is not intended as, and must not be construed to be, a catalog of available implementations or their features. Readers are advised to note that other implementations may exist. According to RFC 7942, "this will allow reviewers and working groups to assign due consideration to documents that have the benefit of running code, which may serve as evidence of valuable experimentation and feedback that have made the implemented protocols more mature. It is up to the individual working groups to use this information as they see fit". * OpenBGPD [openbgpd] * FRRouting [frr] * neo-bgp (bgp.tools) [neo-bgp] * BIRD [BIRD] Patches to recognize error code 8 were merged into OpenBSD's and the- tcpdump-group's tcpdump implementations. Authors' Addresses Job Snijders Fastly Amsterdam Netherlands Email: job@fastly.com Ben Cartwright-Cox Port 179 Ltd London United Kingdom Email: ben@benjojo.co.uk Snijders, et al. Expires 7 February 2025 [Page 9] Internet-Draft BGP SendHoldTimer August 2024 Yingzhen Qu Futurewei Technologies Santa Clara, United States Email: yingzhen.ietf@gmail.com Snijders, et al. Expires 7 February 2025 [Page 10]