Internet Draft Mark Bakke Jim Muchow Expires September 2003 Cisco Systems March 2003 Definitions of Managed Objects for User Identity Authentication Status of this Memo This document is an Internet-Draft and is subject to all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.html. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Copyright Notice Copyright (C) The Internet Society (2003). All Rights Reserved. Abstract This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in TCP/IP based internets. In particular it defines objects for managing user identities and the names, addresses, and credentials required to authenticate them, for use with various protocols. This draft was motivated by the need for the configuration of authenticated user identities for the iSCSI protocol, but has been extended to be useful for other protocols that have similar requirements. It is important to note that this MIB provides only the set of identities and the means to authenticate them; it is the responsibility of other MIBs making use of this one to tie them to authorization lists. Bakke, Muchow Expires September 2003 [Page 1] Internet Draft IPS Authentication MIB March 2003 Acknowledgments In addition to the authors, several people contributed to the development of this MIB through discussions of authentication, authorization, and access within the iSCSI MIB and security teams, including John Hufferd, Marjorie Krueger, Keith McCloghrie, Tom McSweeney, Steve Senum, and Josh Tseng. Thanks also to Bill Studenmund (Wasabi Systems) for adding the Kerberos method, and to Ayman Ghanem for finding and suggesting changes to several problems found in the MIB. Thanks especially to Keith McCloghrie for serving as advisor for this MIB. Table of Contents 1. Introduction..............................................2 2. The Internet-Standard Management Framework................3 3. Relationship to Other MIBs................................3 4. Discussion................................................3 4.1. Authentication MIB Object Model.........................4 4.2. ipsAuthInstance.........................................5 4.3. ipsAuthIdentity.........................................5 4.4. ipsAuthIdentityName.....................................5 4.5. ipsAuthIdentityAddress..................................6 4.6. ipsAuthCredential.......................................7 4.7. IP, Fibre Channel, and Other Addresses..................7 4.8. Descriptors: Using OIDs in Place of Enumerated Types....8 4.9. Notifications...........................................8 5. MIB Definitions...........................................9 6. Security Considerations..................................28 7. Normative References.....................................29 8. Informative References...................................29 9. Authors' Addresses.......................................30 10. IPR Notice..............................................30 11. Full Copyright Notice...................................31 1. Introduction This MIB will be used to configure and/or look at the configuration of user identities and their authentication information. For the purposes of this MIB, a "user" identity does not need to be an actual person; a user can also be a host, an application, a cluster of hosts, or any other identifiable entity that can be authenticated and granted access to a resource. Most objects in this MIB have a MAX-ACCESS of read-create; the MIB is Bakke, Muchow Expires September 2003 [Page 2] Internet Draft IPS Authentication MIB March 2003 intended to allow configuration of user identities and their names, addresses, and credentials. MIN-ACCESS for all objects is read-only for those implementations that configure through other means, but require the ability to monitor user identities. 2. The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580]. 3. Relationship to Other MIBs The identity authentication MIB does not directly address objects within other MIBs. The identity address objects contain IPv4, IPv6, or other address types, and as such may be indirectly related to objects within the IPv4 MIB [RFC1213] [RFC2011] or IPv6 [RFC2465] MIB. This MIB does not cover authorization. This should generally be done in MIBs that reference identities in this one. It also does not cover login or authentication failure statistics or notifications, as these are all fairly application-specific, and not generic enough to include here. The user identity objects within this MIB are typically referenced from other MIBs by a RowPointer within that MIB. A MIB containing resources for which it requires a list of authorized user identities may create such a list, with a single RowPointer within each list element pointing to a user identity within this MIB. This is neither required nor restricted by this MIB. 4. Discussion This MIB structure is intended to allow the configuration of a list of user identities, each with a list of names, addresses, Bakke, Muchow Expires September 2003 [Page 3] Internet Draft IPS Authentication MIB March 2003 credentials, and certificates which when combined will authenticate that identity. The authentication MIB is structured around two primary "objects", the authentication instance, and the identity, which serve as containers for the remainder of the objects. This section contains a brief description of the "object" hierarchy and a description of each object, followed by a discussion of the actual SNMP table structure within the objects. 4.1. Authentication MIB Object Model The top-level object in this structure is the authentication instance, which "contains" all of the other objects. The indexing hierarchy of this MIB looks like: ipsAuthInstance -- A distinct authentication entity within the managed system. -- Most implementations will have just one of these. ipsAuthIdentity -- A user identity, consisting of a set of identity names, -- addresses, and credentials reflected in the following -- objects, as well as a RowPointer to an ipsAuthCertificate. ipsAuthIdentityName -- A name for a user identity. A name should be globally -- unique, and unchanging over time. Some protocols may -- not require this one. ipsAuthIdentityAddress -- An address range, typically but not necessarily an -- IPv4, IPv6, or Fibre Channel address range, at which -- the identity is allowed to reside. ipsAuthCredential -- A single credential, such as a CHAP username/password, -- which can ipsAuthenticate the identity. ipsAuthCredChap -- CHAP-specific attributes for an ipsAuthCredential ipsAuthCredSrp -- SRP-specific attributes ipsAuthCredKerberos -- Kerberos-specific attributes Each identity contains the information necessary to authenticate a particular end-point that wishes to access a service, such as iSCSI. An identity can contain multiple names, addresses, and credentials. Bakke, Muchow Expires September 2003 [Page 4] Internet Draft IPS Authentication MIB March 2003 4.2. ipsAuthInstance The ipsAuthInstanceAttributesTable is the primary table of the authentication MIB. Every other table entry in this MIB includes the index of an ipsAuthInstanceAttributesEntry as its primary index. An authentication instance is basically a managed set of identities. Many implementations will include just one authentication instance row in this table. However, there will be cases where multiple rows in this table may be used: - A large system may be "partitioned" into multiple, distinct virtual systems, perhaps sharing the SNMP agent but not their lists of identities. Each virtual system would have its own authentication instance. - A set of stackable systems, each with their own set of identities, may be managed by a common SNMP agent. Each individual system would have its own authentication instance. - Multiple protocols, each with their own set of identities, may exist within a single system and be managed by a single SNMP agent. In this case, each protocol may have its own authentication instance. 4.3. ipsAuthIdentity The ipsAuthIdentAttributesTable contains one entry for each configured user identity. The identity contains only a description of what the identity is used for; its attributes are all contained in other tables, since they can have multiple values. Other MIBs containing lists of users authorized to access a particular resource should generally contain a RowPointer to the ipsAuthIdentAttributesEntry which will, if authenticated, be allowed access. All other table entries make use of the indices to this table as their primary indices. 4.4. ipsAuthIdentityName The ipsAuthIdentNameAttributesTable contains a list of UTF-8 names, each of which belong to, and may be used to identify, a particular identity in the authIdentity table. Implementations making use of the authentication MIB may identify Bakke, Muchow Expires September 2003 [Page 5] Internet Draft IPS Authentication MIB March 2003 their resources by names, addresses, or both. A name is typically a unique (within the required scope), unchanging identifier for a resource. It will normally meet some or all of the requirements for a Uniform Resource Name [RFC1737], although a name in the context of this MIB does not need to be a URN. Identifiers that typically change over time should generally be placed into the ipsAuthIdentityAddress table; names that have no uniqueness properties should usually be placed into the description attribute for the identity. An example of an identity name is the iSCSI Name, defined in [ISCSI]. If this table contains no entries associated with a particular user identity, the implementation does not need to check any name parameters when authenticating that identity. If the table contains multiple entries associated with a particular user identity, the implementation should consider a match with any one of these entries to be valid. 4.5. ipsAuthIdentityAddress The ipsAuthIdentAddrAttributesTable contains a list of addresses at which the identity may be authenticated. For example, an identity may be allowed access to a resource only from a certain IP address, or only if its address is in a certain range or set of ranges. Each entry contains a starting and ending address. If a single address is desired in the list, both starting and ending addresses must be identical. Each entry contains an AddrType attribute. This attribute contains an enumeration registered as an IANA Address Family type [IANA-AF]. Although many implementations will use IPv4 or IPv6 address types for these entries, any IANA-registered type may be used, as long as it makes sense to the application. Matching any address within any range within the list associated with a particular identity is considered to be a valid match. If no entries are present in this list for a given identity, its address is not checked during authentication. Netmasks are not supported, since an address range can express the same thing with more flexibility. An application specifying addresses using network masks may do so, and convert to and from address ranges when reading or writing this MIB. Bakke, Muchow Expires September 2003 [Page 6] Internet Draft IPS Authentication MIB March 2003 4.6. ipsAuthCredential The ipsAuthCredentialAttributesTable contains a list of credentials, each of which may authenticate a particular identity. Each credential contains an authentication method to be used, such as CHAP [RFC1994], SRP [RFC2945], or Kerberos [RFC1510]. This attribute contains an object identifier instead of an enumerated type, allowing other MIBs to add their own authentication methods, without modifying this MIB. For each entry in this table, there will exist an entry in another table containing its attributes. The table in which to place the entry depends on the AuthMethod attribute: CHAP If the AuthMethod is set to the CHAP OID, an entry using the same indices as the ipsAuthCredential will exist in the ipsAuthCredChap table, which contains the CHAP username. SRP If the AuthMethod is set to the SRP OID, an entry using the same indices as the ipsAuthCredential will exist in the ipsAuthCredSrp table, which contains the SRP username. Kerberos If the AuthMethod is set to the Kerberos OID, an entry using the same indices as the ipsAuthCredential will exist in the ipsAuthCredKerberos table, which contains the Kerberos principal. Other If the AuthMethod is set to any OID not defined in this MIB, an entry using the same indices as the ipsAuthCredential entry should be placed in the other MIB that define whatever attributes are needed for that type of credential. 4.7. IP, Fibre Channel, and Other Addresses The IP addresses in this MIB are represented by two attributes, one of type AddressFamilyNumbers, and the other of type AuthAddress. Each address can take on any of the types within the list of address family numbers; the most likely being IPv4, IPv6, or one of the Fibre Channel address types. The type AuthAddress is an octet string. If the address family is IPv4 or IPv6, the format is taken from the InetAddress specified in [RFC3291]. If the address family is one of the Fibre Channel types, the format is identical to the FcNameIdOrZero type defined in [FCMGMT]. Bakke, Muchow Expires September 2003 [Page 7] Internet Draft IPS Authentication MIB March 2003 4.8. Descriptors: Using OIDs in Place of Enumerated Types Some attributes, particularly the authentication method attribute, would normally require an enumerated type. However, implementations will likely need to add new authentication method types of their own, without extending this MIB. To make this work, the MIB defines a set of object identities within ipsAuthDescriptors. Each of these object identities is basically an enumerated type. Attributes that make use of these object identities have a value which is an OID instead of an enumerated type. These OIDs can either indicate the object identities defined in this MIB, or object identities defined elsewhere, such as in an enterprise MIB. Those implementations that add their own authentication methods should also define a corresponding object identity for each of these methods within their own enterprise MIB, and return its OID whenever one of these attributes is using that method. 4.9. Notifications Monitoring of authentication failures and other notification events are outside the scope of this MIB, as they are generally application- specific. No notifications are provided or required. Bakke, Muchow Expires September 2003 [Page 8] Internet Draft IPS Authentication MIB March 2003 5. MIB Definitions IPS-AUTH-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY, Unsigned32, experimental FROM SNMPv2-SMI TEXTUAL-CONVENTION, RowStatus, AutonomousType FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- RFC 2571 AddressFamilyNumbers FROM IANA-ADDRESS-FAMILY-NUMBERS-MIB ; ipsAuthModule MODULE-IDENTITY LAST-UPDATED "200211010000Z" -- November 1, 2002 ORGANIZATION "IETF IPS Working Group" CONTACT-INFO " Mark Bakke Postal: Cisco Systems, Inc 6450 Wedgwood Road, Suite 130 Maple Grove, MN USA 55311 Tel: +1 763-398-1000 Fax: +1 763-398-1001 E-mail: mbakke@cisco.com Jim Muchow Postal: Cisco Systems, Inc 6450 Wedgwood Road, Suite 130 Maple Grove, MN USA 55311 Tel: +1 763-398-1000 Fax: +1 763-398-1001 Bakke, Muchow Expires September 2003 [Page 9] Internet Draft IPS Authentication MIB March 2003 E-mail: jmuchow@cisco.com" DESCRIPTION "The IP Storage Authentication MIB module." REVISION "200211010000Z" -- November 1, 2002 DESCRIPTION "Initial revision published as RFC xxxx." --::= { mib-2 xx } -- in case you want to COMPILE ::= { experimental 99999 } ipsAuthObjects OBJECT IDENTIFIER ::= { ipsAuthModule 1 } ipsAuthNotifications OBJECT IDENTIFIER ::= { ipsAuthModule 2 } ipsAuthConformance OBJECT IDENTIFIER ::= { ipsAuthModule 3 } -- Textual Conventions IpsAuthAddress ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "IP Storage requires the use of address information that uses not only the InetAddress type defined in the INET-ADDRESS-MIB, but also Fibre Channel type defined in the Fibre Channel Management MIB. Although these address types are recognized in the IANA Address Family Numbers MIB, the addressing mechanisms have not been merged into a well-known, common type. This data type, the IpsAuthAddress, performs this function for this MIB." REFERENCE "IANA-ADDRESS-FAMILY-NUMBERS-MIB; INET-ADDRESS-MIB (RFC 2851); Fibre Channel Management MIB (presently defined in draft-ietf-ips-fcmgmt-mib-01.txt)." SYNTAX OCTET STRING (SIZE(0..255)) ------------------------------------------------------------------------ ipsAuthDescriptors OBJECT IDENTIFIER ::= { ipsAuthObjects 1 } ipsAuthMethodTypes OBJECT IDENTIFIER ::= { ipsAuthDescriptors 1 } ipsAuthMethodNone OBJECT-IDENTITY STATUS current DESCRIPTION "The authoritative identifier when no authentication method is used." REFERENCE "iSCSI Protocol Specification." Bakke, Muchow Expires September 2003 [Page 10] Internet Draft IPS Authentication MIB March 2003 ::= { ipsAuthMethodTypes 1 } ipsAuthMethodSrp OBJECT-IDENTITY STATUS current DESCRIPTION "The authoritative identifier when the authentication method is SRP." REFERENCE "iSCSI Protocol Specification." ::= { ipsAuthMethodTypes 2 } ipsAuthMethodChap OBJECT-IDENTITY STATUS current DESCRIPTION "The authoritative identifier when the authentication method is CHAP." REFERENCE "iSCSI Protocol Specification." ::= { ipsAuthMethodTypes 3 } ipsAuthMethodKerberos OBJECT-IDENTITY STATUS current DESCRIPTION "The authoritative identifier when the authentication method is Kerberos." REFERENCE "iSCSI Protocol Specification." ::= { ipsAuthMethodTypes 4 } ---------------------------------------------------------------------- ipsAuthInstance OBJECT IDENTIFIER ::= { ipsAuthObjects 2 } -- Instance Attributes Table ipsAuthInstanceAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsAuthInstanceAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of Authentication instances present on the system." ::= { ipsAuthInstance 2 } ipsAuthInstanceAttributesEntry OBJECT-TYPE SYNTAX IpsAuthInstanceAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a particular Authentication instance." INDEX { ipsAuthInstIndex } Bakke, Muchow Expires September 2003 [Page 11] Internet Draft IPS Authentication MIB March 2003 ::= { ipsAuthInstanceAttributesTable 1 } IpsAuthInstanceAttributesEntry ::= SEQUENCE { ipsAuthInstIndex Unsigned32, ipsAuthInstDescr SnmpAdminString } ipsAuthInstIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to uniquely identify a particular authentication instance." ::= { ipsAuthInstanceAttributesEntry 1 } ipsAuthInstDescr OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "An octet string, determined by the implementation to describe the authentication instance. When only a single instance is present, this object may be set to the zero-length string; with multiple authentication instances, it may be used in an implementation-dependent manner to describe the purpose of the respective instance." ::= { ipsAuthInstanceAttributesEntry 2 } ipsAuthIdentity OBJECT IDENTIFIER ::= { ipsAuthObjects 3 } -- User Identity Attributes Table ipsAuthIdentAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsAuthIdentAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of user identities, each belonging to a particular ipsAuthInstance." ::= { ipsAuthIdentity 1 } ipsAuthIdentAttributesEntry OBJECT-TYPE SYNTAX IpsAuthIdentAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information Bakke, Muchow Expires September 2003 [Page 12] Internet Draft IPS Authentication MIB March 2003 describing a user identity within an authentication instance on this node." INDEX { ipsAuthInstIndex, ipsAuthIdentIndex } ::= { ipsAuthIdentAttributesTable 1 } IpsAuthIdentAttributesEntry ::= SEQUENCE { ipsAuthIdentIndex Unsigned32, ipsAuthIdentDescription SnmpAdminString, ipsAuthIdentRowStatus RowStatus } ipsAuthIdentIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to uniquely identify a particular identity instance within an authentication instance present on the node." ::= { ipsAuthIdentAttributesEntry 1 } ipsAuthIdentDescription OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "An octet string describing this particular identity." ::= { ipsAuthIdentAttributesEntry 2 } ipsAuthIdentRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This field allows entries to be dynamically added and removed from this table via SNMP." ::= { ipsAuthIdentAttributesEntry 3 } ipsAuthIdentityName OBJECT IDENTIFIER ::= { ipsAuthObjects 4 } -- User Initiator Name Attributes Table ipsAuthIdentNameAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsAuthIdentNameAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of unique names that can be used to positively Bakke, Muchow Expires September 2003 [Page 13] Internet Draft IPS Authentication MIB March 2003 identify a particular user identity." ::= { ipsAuthIdentityName 1 } ipsAuthIdentNameAttributesEntry OBJECT-TYPE SYNTAX IpsAuthIdentNameAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a unique identity name which can be used to identify a user identity within a particular authentication instance." INDEX { ipsAuthInstIndex, ipsAuthIdentIndex, ipsAuthIdentNameIndex } ::= { ipsAuthIdentNameAttributesTable 1 } IpsAuthIdentNameAttributesEntry ::= SEQUENCE { ipsAuthIdentNameIndex Unsigned32, ipsAuthIdentName SnmpAdminString, ipsAuthIdentNameRowStatus RowStatus } ipsAuthIdentNameIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to uniquely identify a particular identity name instance within an ipsAuthIdentity within an authentication instance." ::= { ipsAuthIdentNameAttributesEntry 1 } ipsAuthIdentName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "A character string which is the unique name of an identity that may be used to identify this ipsAuthIdent entry." ::= { ipsAuthIdentNameAttributesEntry 2 } ipsAuthIdentNameRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This field allows entries to be dynamically added and Bakke, Muchow Expires September 2003 [Page 14] Internet Draft IPS Authentication MIB March 2003 removed from this table via SNMP." ::= { ipsAuthIdentNameAttributesEntry 3 } ipsAuthIdentityAddress OBJECT IDENTIFIER ::= { ipsAuthObjects 5 } -- User Initiator Address Attributes Table ipsAuthIdentAddrAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsAuthIdentAddrAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of address ranges that are allowed to serve as the endpoint addresses of a particular identity. An address range includes a starting and ending address and an optional netmask, and an address type indicator, which can specify whether the address is IPv4, IPv6, FC-WWPN, or FC-WWNN." ::= { ipsAuthIdentityAddress 1 } ipsAuthIdentAddrAttributesEntry OBJECT-TYPE SYNTAX IpsAuthIdentAddrAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to an address range which is used as part of the authentication of an identity within an authentication instance on this node." INDEX { ipsAuthInstIndex, ipsAuthIdentIndex, ipsAuthIdentAddrIndex } ::= { ipsAuthIdentAddrAttributesTable 1 } IpsAuthIdentAddrAttributesEntry ::= SEQUENCE { ipsAuthIdentAddrIndex Unsigned32, ipsAuthIdentAddrType AddressFamilyNumbers, ipsAuthIdentAddrStart IpsAuthAddress, ipsAuthIdentAddrEnd IpsAuthAddress, ipsAuthIdentAddrRowStatus RowStatus } ipsAuthIdentAddrIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to uniquely identify a particular ipsAuthIdentAddress instance within an Bakke, Muchow Expires September 2003 [Page 15] Internet Draft IPS Authentication MIB March 2003 ipsAuthIdentity within an authentication instance present on the node." ::= { ipsAuthIdentAddrAttributesEntry 1 } ipsAuthIdentAddrType OBJECT-TYPE SYNTAX AddressFamilyNumbers MAX-ACCESS read-create STATUS current DESCRIPTION "The type of Address in the ipsAuthIdentAddress start, end, and mask fields. This type is taken from the IANA address family types; more types may be registered independently of this MIB." ::= { ipsAuthIdentAddrAttributesEntry 2 } ipsAuthIdentAddrStart OBJECT-TYPE SYNTAX IpsAuthAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The starting address of the allowed address range." ::= { ipsAuthIdentAddrAttributesEntry 3 } ipsAuthIdentAddrEnd OBJECT-TYPE SYNTAX IpsAuthAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The ending address of the allowed address range. If the ipsAuthIdentAddrEntry specifies a single address, this shall match the ipsAuthIdentAddrStart." ::= { ipsAuthIdentAddrAttributesEntry 4 } ipsAuthIdentAddrRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This field allows entries to be dynamically added and removed from this table via SNMP." ::= { ipsAuthIdentAddrAttributesEntry 5 } ipsAuthCredential OBJECT IDENTIFIER ::= { ipsAuthObjects 6 } -- Credential Attributes Table ipsAuthCredentialAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsAuthCredentialAttributesEntry Bakke, Muchow Expires September 2003 [Page 16] Internet Draft IPS Authentication MIB March 2003 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of credentials related to user identities that are allowed as valid authenticators of the particular identity." ::= { ipsAuthCredential 1 } ipsAuthCredentialAttributesEntry OBJECT-TYPE SYNTAX IpsAuthCredentialAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a credential which authenticates a user identity within an authentication instance." INDEX { ipsAuthInstIndex, ipsAuthIdentIndex, ipsAuthCredIndex } ::= { ipsAuthCredentialAttributesTable 1 } IpsAuthCredentialAttributesEntry ::= SEQUENCE { ipsAuthCredIndex Unsigned32, ipsAuthCredAuthMethod AutonomousType, ipsAuthCredRowStatus RowStatus } ipsAuthCredIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer used to uniquely identify a particular Credential instance within an instance present on the node." ::= { ipsAuthCredentialAttributesEntry 1 } ipsAuthCredAuthMethod OBJECT-TYPE SYNTAX AutonomousType MAX-ACCESS read-create STATUS current DESCRIPTION "This object contains an OBJECT IDENTIFIER which identifies the authentication method used with this credential. Some standardized values for this object are defined within the ipsAuthMethods subtree." ::= { ipsAuthCredentialAttributesEntry 2 } Bakke, Muchow Expires September 2003 [Page 17] Internet Draft IPS Authentication MIB March 2003 ipsAuthCredRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This field allows entries to be dynamically added and removed from this table via SNMP." ::= { ipsAuthCredentialAttributesEntry 3 } ipsAuthCredChap OBJECT IDENTIFIER ::= { ipsAuthObjects 7 } -- Credential Chap-Specific Attributes Table ipsAuthCredChapAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsAuthCredChapAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of CHAP attributes for credentials that use ipsAuthMethodChap as its ipsAuthCredAuthMethod." ::= { ipsAuthCredChap 1 } ipsAuthCredChapAttributesEntry OBJECT-TYPE SYNTAX IpsAuthCredChapAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a credential which uses ipsAuthMethodChap as their ipsAuthCredAuthMethod." INDEX { ipsAuthInstIndex, ipsAuthIdentIndex, ipsAuthCredIndex } ::= { ipsAuthCredChapAttributesTable 1 } IpsAuthCredChapAttributesEntry ::= SEQUENCE { ipsAuthCredChapUserName SnmpAdminString, ipsAuthCredChapPassword SnmpAdminString, ipsAuthCredChapRowStatus RowStatus } ipsAuthCredChapUserName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "An octet string containing the CHAP user name for this credential." ::= { ipsAuthCredChapAttributesEntry 1 } Bakke, Muchow Expires September 2003 [Page 18] Internet Draft IPS Authentication MIB March 2003 ipsAuthCredChapPassword OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "An octet string containing the password for this credential. If written, it changes the password for the credential. If read, it returns a zero-length string." ::= { ipsAuthCredChapAttributesEntry 2 } ipsAuthCredChapRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This field allows entries to be dynamically added and removed from this table via SNMP." ::= { ipsAuthCredChapAttributesEntry 3 } ipsAuthCredSrp OBJECT IDENTIFIER ::= { ipsAuthObjects 8 } -- Credential Srp-Specific Attributes Table ipsAuthCredSrpAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsAuthCredSrpAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of SRP attributes for credentials that use ipsAuthMethodSrp as their ipsAuthCredAuthMethod." ::= { ipsAuthCredSrp 1 } ipsAuthCredSrpAttributesEntry OBJECT-TYPE SYNTAX IpsAuthCredSrpAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (row) containing management information applicable to a credential which uses ipsAuthMethodSrp as its ipsAuthCredAuthMethod." INDEX { ipsAuthInstIndex, ipsAuthIdentIndex, ipsAuthCredIndex } ::= { ipsAuthCredSrpAttributesTable 1 } IpsAuthCredSrpAttributesEntry ::= SEQUENCE { ipsAuthCredSrpUserName SnmpAdminString, ipsAuthCredSrpPassword SnmpAdminString, Bakke, Muchow Expires September 2003 [Page 19] Internet Draft IPS Authentication MIB March 2003 ipsAuthCredSrpRowStatus RowStatus } ipsAuthCredSrpUserName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "An octet string containing the CHAP user name for this credential." ::= { ipsAuthCredSrpAttributesEntry 1 } ipsAuthCredSrpPassword OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "An octet string containing the password for this credential. If written, it changes the password for the credential. If read, it returns a zero-length string." ::= { ipsAuthCredSrpAttributesEntry 2 } ipsAuthCredSrpRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This field allows entries to be dynamically added and removed from this table via SNMP." ::= { ipsAuthCredSrpAttributesEntry 3 } ipsAuthCredKerberos OBJECT IDENTIFIER ::= { ipsAuthObjects 9 } -- Credential Kerberos-Specific Attributes Table ipsAuthCredKerbAttributesTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsAuthCredKerbAttributesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of Kerberos attributes for credentials that use ipsAuthMethodKerberos as their ipsAuthCredAuthMethod." ::= { ipsAuthCredKerberos 1 } ipsAuthCredKerbAttributesEntry OBJECT-TYPE SYNTAX IpsAuthCredKerbAttributesEntry MAX-ACCESS not-accessible Bakke, Muchow Expires September 2003 [Page 20] Internet Draft IPS Authentication MIB March 2003 STATUS current DESCRIPTION "An entry (row) containing management information applicable to a credential which uses ipsAuthMethodKerberos as its ipsAuthCredAuthMethod." INDEX { ipsAuthInstIndex, ipsAuthIdentIndex, ipsAuthCredIndex } ::= { ipsAuthCredKerbAttributesTable 1 } IpsAuthCredKerbAttributesEntry ::= SEQUENCE { ipsAuthCredKerbPrincipal SnmpAdminString, ipsAuthCredKerbRowStatus RowStatus } ipsAuthCredKerbPrincipal OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "An octet string containing a Kerberos principal for this credential." ::= { ipsAuthCredKerbAttributesEntry 1 } ipsAuthCredKerbRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This field allows entries to be dynamically added and removed from this table via SNMP." ::= { ipsAuthCredKerbAttributesEntry 2 } ------------------------------------------------------------------------ -- Notifications -- There are no notifications necessary in this MIB. ------------------------------------------------------------------------ -- Conformance Statements ipsAuthGroups OBJECT IDENTIFIER ::= { ipsAuthConformance 1 } ipsAuthInstanceAttributesGroup OBJECT-GROUP OBJECTS { ipsAuthInstDescr } STATUS current DESCRIPTION Bakke, Muchow Expires September 2003 [Page 21] Internet Draft IPS Authentication MIB March 2003 "A collection of objects providing information about authentication instances." ::= { ipsAuthGroups 1 } ipsAuthIdentAttributesGroup OBJECT-GROUP OBJECTS { ipsAuthIdentDescription, ipsAuthIdentRowStatus } STATUS current DESCRIPTION "A collection of objects providing information about user identities within an authentication instance." ::= { ipsAuthGroups 2 } ipsAuthIdentNameAttributesGroup OBJECT-GROUP OBJECTS { ipsAuthIdentName, ipsAuthIdentNameRowStatus } STATUS current DESCRIPTION "A collection of objects providing information about user names within user identities within an authentication instance." ::= { ipsAuthGroups 3 } ipsAuthIdentAddrAttributesGroup OBJECT-GROUP OBJECTS { ipsAuthIdentAddrType, ipsAuthIdentAddrStart, ipsAuthIdentAddrEnd, ipsAuthIdentAddrRowStatus } STATUS current DESCRIPTION "A collection of objects providing information about address ranges within user identities within an authentication instance." ::= { ipsAuthGroups 4 } ipsAuthIdentCredAttributesGroup OBJECT-GROUP OBJECTS { ipsAuthCredAuthMethod, ipsAuthCredRowStatus } STATUS current DESCRIPTION Bakke, Muchow Expires September 2003 [Page 22] Internet Draft IPS Authentication MIB March 2003 "A collection of objects providing information about credentials within user identities within an authentication instance." ::= { ipsAuthGroups 5 } ipsAuthIdentChapAttrGroup OBJECT-GROUP OBJECTS { ipsAuthCredChapUserName, ipsAuthCredChapPassword, ipsAuthCredChapRowStatus } STATUS current DESCRIPTION "A collection of objects providing information about CHAP credentials within user identities within an authentication instance." ::= { ipsAuthGroups 6 } ipsAuthIdentSrpAttrGroup OBJECT-GROUP OBJECTS { ipsAuthCredSrpUserName, ipsAuthCredSrpPassword, ipsAuthCredSrpRowStatus } STATUS current DESCRIPTION "A collection of objects providing information about SRP credentials within user identities within an authentication instance." ::= { ipsAuthGroups 7 } ipsAuthIdentKerberosAttrGroup OBJECT-GROUP OBJECTS { ipsAuthCredKerbPrincipal, ipsAuthCredKerbRowStatus } STATUS current DESCRIPTION "A collection of objects providing information about Kerberos credentials within user identities within an authentication instance." ::= { ipsAuthGroups 8 } ------------------------------------------------------------------------ ipsAuthCompliances OBJECT IDENTIFIER ::= { ipsAuthConformance 2 } ipsAuthComplianceV1 MODULE-COMPLIANCE Bakke, Muchow Expires September 2003 [Page 23] Internet Draft IPS Authentication MIB March 2003 STATUS current DESCRIPTION "Initial version of compliance statement based on initial version of MIB. The Instance and Identity groups are mandatory; at least one of the other groups (Name, Address, Credential, Certificate) is also mandatory for any given implementation." MODULE -- this module MANDATORY-GROUPS { ipsAuthInstanceAttributesGroup, ipsAuthIdentAttributesGroup } -- Conditionally mandatory groups to be included with -- the mandatory groups when necessary. GROUP ipsAuthIdentNameAttributesGroup DESCRIPTION "This group is mandatory for all implementations that make use of unique identity names." GROUP ipsAuthIdentAddrAttributesGroup DESCRIPTION "This group is mandatory for all implementations that use addresses to help authenticate identities." GROUP ipsAuthIdentCredAttributesGroup DESCRIPTION "This group is mandatory for all implementations that use credentials to help authenticate identities." GROUP ipsAuthIdentChapAttrGroup DESCRIPTION "This group is mandatory for all implementations that use CHAP to help authenticate identities. The ipsAuthIdentCredAttributesGroup must be implemented if this group is implemented." GROUP ipsAuthIdentSrpAttrGroup DESCRIPTION "This group is mandatory for all implementations that use SRP to help authenticate identities. The ipsAuthIdentCredAttributesGroup must be implemented if this group is implemented." Bakke, Muchow Expires September 2003 [Page 24] Internet Draft IPS Authentication MIB March 2003 GROUP ipsAuthIdentKerberosAttrGroup DESCRIPTION "This group is mandatory for all implementations that use Kerberos to help authenticate identities. The ipsAuthIdentCredAttributesGroup must be implemented if this group is implemented." OBJECT ipsAuthInstDescr MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ipsAuthIdentDescription MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ipsAuthIdentRowStatus SYNTAX INTEGER { active(1) } -- subset of RowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT ipsAuthIdentName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ipsAuthIdentNameRowStatus SYNTAX INTEGER { active(1) } -- subset of RowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT ipsAuthIdentAddrType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ipsAuthIdentAddrStart MIN-ACCESS read-only Bakke, Muchow Expires September 2003 [Page 25] Internet Draft IPS Authentication MIB March 2003 DESCRIPTION "Write access is not required." OBJECT ipsAuthIdentAddrEnd MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ipsAuthIdentAddrRowStatus SYNTAX INTEGER { active(1) } -- subset of RowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT ipsAuthCredAuthMethod MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ipsAuthCredRowStatus SYNTAX INTEGER { active(1) } -- subset of RowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT ipsAuthCredChapUserName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ipsAuthCredChapPassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ipsAuthCredChapRowStatus SYNTAX INTEGER { active(1) } -- subset of RowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: Bakke, Muchow Expires September 2003 [Page 26] Internet Draft IPS Authentication MIB March 2003 active(1)." OBJECT ipsAuthCredSrpUserName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ipsAuthCredSrpPassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ipsAuthCredSrpRowStatus SYNTAX INTEGER { active(1) } -- subset of RowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT ipsAuthCredKerbPrincipal MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT ipsAuthCredKerbRowStatus SYNTAX INTEGER { active(1) } -- subset of RowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." ::= { ipsAuthCompliances 1 } END Bakke, Muchow Expires September 2003 [Page 27] Internet Draft IPS Authentication MIB March 2003 6. Security Considerations There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability: All tables provide the ability to set up which credentials may be used to access services on the managed system, to remove legitimate credentials (a denial of service), or to remove individual credentials to weaken the requirements for access of a particular service. In addition, write access may be used to change CHAP or SRP passwords to a known value. Write access must always be tightly controlled. Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability: All tables provide the ability to find out which names, addresses, and credentials would be required to access services on the managed system. If these credentials are easily spoofed (particularly the name or address), read access to the MIB must be tightly controlled. SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPsec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module. It is RECOMMENDED that implementors consider the security features as provided by the SNMPv3 framework (see [RFC3410], section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy). Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to Bakke, Muchow Expires September 2003 [Page 28] Internet Draft IPS Authentication MIB March 2003 the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 7. Normative References [RFC2578] K. McCloghrie, D. Perkins, J. Schoenwaelder, J. Case, M. Rose, and S. Waldbusser, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [RFC2579] K. McCloghrie, D. Perkins, J. Schoenwaelder, J. Case, M. Rose, and S. Waldbusser, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] K. McCloghrie, D. Perkins, J. Schoenwaelder, J. Case, M. Rose, and S. Waldbusser, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [RFC3291] M. Daniele, et. al., "Textual Conventions for Internet Network Addresses", RFC 3291, May 2002. [IANA-AF] IANA, "IANA Address Family Numbers MIB", http://www.iana.org/assignments/ianaaddressfamilynumbers-mib [RFC1213] K. McCloghrie, M. Rose, "Management Information Base for Network Management of TCP/IP-based internets:MIB-II", March 1991. [RFC2011] K. McCloghrie, "SNMPv2 Management Information Base for the Internet Protocol using SMIv2", November 1996. [RFC2465] D. Haskin, S. Onishi, "Management Information Base for IP Version 6: Textual Conventions and General Group", December 1998. 8. Informative References [RFC3410] J. Case, R. Mundy, D. Partain, and B. Stewart, "Introduction and Applicability Statements for Internet-Standard Management Framework", RFC 3410, December 2002. [ISCSI] Satran, J., et. al., "iSCSI", Work in Progress, draft-ietf- ips-iscsi-20, January 2003. [RFC1737] K. Sollins, L. Masinter, "Functional Requirements for Uniform Resource Names", December 1994. Bakke, Muchow Expires September 2003 [Page 29] Internet Draft IPS Authentication MIB March 2003 [RFC1994] W. Simpson, "PPP Challenge Handshake Authentication Protocol (CHAP)", August 1996. [RFC1510] J. Kohl, C. Neuman, "The Kerberos Network Authentication Service (V5)", September 1993. [RFC2945] T. Wu, "The SRP Authentication and Key Exchange System", September 2000. [FCMGMT] K. McCloghrie, "Fibre Channel Management MIB", Work in Progress, draft-ietf-ips-fcmgmt-mib-03, October 2002. 9. Authors' Addresses Mark Bakke Postal: Cisco Systems, Inc 6450 Wedgwood Road, Suite 130 Maple Grove, MN USA 55311 Tel: +1 763-398-1000 Fax: +1 763-398-1001 E-mail: mbakke@cisco.com Jim Muchow Postal: Cisco Systems, Inc 6450 Wedgwood Road, Suite 130 Maple Grove, MN USA 55311 Tel: +1 763-398-1000 Fax: +1 763-398-1001 E-mail: jamesdmuchow@yahoo.com" 10. IPR Notice The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found in BCP-11. Copies of claims of rights made Bakke, Muchow Expires September 2003 [Page 30] Internet Draft IPS Authentication MIB March 2003 available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementors or users of this specification can be obtained from the IETF Secretariat. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director. 11. Full Copyright Notice Copyright (C) The Internet Society (2003). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE." Bakke, Muchow Expires September 2003 [Page 31]