Network Working Group L. Jakab Internet-Draft A. Cabellos-Aparicio Intended status: Informational F. Coras Expires: March 16, 2013 J. Domingo-Pascual Technical University of Catalonia D. Lewis Cisco Systems September 12, 2012 LISP Network Element Deployment Considerations draft-ietf-lisp-deployment-04.txt Abstract This document discusses the different scenarios for the deployment of the new network elements introduced by the Locator/Identifier Separation Protocol (LISP). Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on March 16, 2013. Copyright Notice Copyright (c) 2012 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must Jakab, et al. Expires March 16, 2013 [Page 1] Internet-Draft LISP Deployment September 2012 include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Tunnel Routers . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1. Customer Edge . . . . . . . . . . . . . . . . . . . . . . 4 2.2. Provider Edge . . . . . . . . . . . . . . . . . . . . . . 5 2.3. Split ITR/ETR . . . . . . . . . . . . . . . . . . . . . . 6 2.4. Inter-Service Provider Traffic Engineering . . . . . . . . 8 2.5. Tunnel Routers Behind NAT . . . . . . . . . . . . . . . . 10 2.5.1. ITR . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.5.2. ETR . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.6. Summary and Feature Matrix . . . . . . . . . . . . . . . . 11 3. Map-Resolvers and Map-Servers . . . . . . . . . . . . . . . . 11 3.1. Map-Servers . . . . . . . . . . . . . . . . . . . . . . . 11 3.2. Map-Resolvers . . . . . . . . . . . . . . . . . . . . . . 12 4. Proxy Tunnel Routers . . . . . . . . . . . . . . . . . . . . . 13 4.1. P-ITR . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4.2. P-ETR . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5. Migration to LISP . . . . . . . . . . . . . . . . . . . . . . 15 5.1. LISP+BGP . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.2. Mapping Service Provider (MSP) P-ITR Service . . . . . . . 16 5.3. Proxy-ITR Route Distribution (PITR-RD) . . . . . . . . . . 17 5.4. Migration Summary . . . . . . . . . . . . . . . . . . . . 19 6. Step-by-Step Example BGP to LISP Migration Procedure . . . . . 20 6.1. Customer Pre-Install and Pre-Turn-up Checklist . . . . . . 20 6.2. Customer Activating LISP Service . . . . . . . . . . . . . 21 6.3. Cut-Over Provider Preparation and Changes . . . . . . . . 22 7. Security Considerations . . . . . . . . . . . . . . . . . . . 22 8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 23 9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 23 10. Informative References . . . . . . . . . . . . . . . . . . . . 23 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 24 Jakab, et al. Expires March 16, 2013 [Page 2] Internet-Draft LISP Deployment September 2012 1. Introduction The Locator/Identifier Separation Protocol (LISP) addresses the scaling issues of the global Internet routing system by separating the current addressing scheme into Endpoint IDentifiers (EIDs) and Routing LOCators (RLOCs). The main protocol specification [I-D.ietf-lisp] describes how the separation is achieved, which new network elements are introduced, and details the packet formats for the data and control planes. LISP assumes that such separation is between the edge and core. While the boundary between both is not strictly defined, one widely accepted definition places it at the border routers of stub autonomous systems, which may carry a partial or complete default- free zone (DFZ) routing table. The initial design of LISP took this location as a baseline for protocol development. However, the applications of LISP go beyond of just decreasing the size of the DFZ routing table, and include improved multihoming and ingress traffic engineering (TE) support for edge networks, and even individual hosts. Throughout the draft we will use the term LISP site to refer to these networks/hosts behind a LISP Tunnel Router. We formally define it as: LISP site: A single host or a set of network elements in an edge network under the administrative control of a single organization, delimited from other networks by LISP Tunnel Router(s). Since LISP is a protocol which can be used for different purposes, it is important to identify possible deployment scenarios and the additional requirements they may impose on the protocol specification and other protocols. Additionally, this document is intended as a guide for the operational community for LISP deployments in their networks. It is expected to evolve as LISP deployment progresses, and the described scenarios are better understood or new scenarios are discovered. Each subsection considers an element type, discussing the impact of deployment scenarios on the protocol specification. For definition of terms, please refer to the appropriate documents (as cited in the respective sections). 2. Tunnel Routers LISP is a map-and-encap protocol, with the main goal of improving global routing scalability. To achieve its goal, it introduces several new network elements, each performing specific functions necessary to separate the edge from the core. The device that is the Jakab, et al. Expires March 16, 2013 [Page 3] Internet-Draft LISP Deployment September 2012 gateway between the edge and the core is called Tunnel Router (xTR), performing one or both of two separate functions: 1. Encapsulating packets originating from an end host to be transported over intermediary (transit) networks towards the other end-point of the communication 2. Decapsulating packets entering from intermediary (transit) networks, originated at a remote end host. The first function is performed by an Ingress Tunnel Router (ITR), the second by an Egress Tunnel Router (ETR). Section 8 of the main LISP specification [I-D.ietf-lisp] has a short discussion of where Tunnel Routers can be deployed and some of the associated advantages and disadvantages. This section adds more detail to the scenarios presented there, and provides additional scenarios as well. 2.1. Customer Edge LISP was designed with deployment at the core-edge boundary in mind, which can be approximated as the set of DFZ routers belonging to non- transit ASes. For the purposes of this document, we will consider this boundary to be consisting of the routers connecting LISP sites to their upstreams. As such, this is the most common expected scenario for xTRs, and this document considers it the reference location, comparing the other scenarios to this one. ISP1 ISP2 | | | | +----+ +----+ +--|xTR1|--|xTR2|--+ | +----+ +----+ | | | | LISP site | +------------------+ Figure 1: xTRs at the customer edge From the LISP site perspective the main advantage of this type of deployment (compared to the one described in the next section) is having direct control over its ingress traffic engineering. This makes it is easy to set up and maintain active/active, active/backup, or more complex TE policies, without involving third parties. Being under the same administrative control, reachability information Jakab, et al. Expires March 16, 2013 [Page 4] Internet-Draft LISP Deployment September 2012 of all ETRs is easier to synchronize, because the necessary control traffic can be allowed between the locators of the ETRs. A correct synchronous global view of the reachability status is thus available, and the Loc-Status-Bits can be set correctly in the LISP data header of outgoing packets. By placing the tunnel router at the edge of the site, existing internal network configuration does not need to be modified. Firewall rules, router configurations and address assignments inside the LISP site remain unchanged. This helps with incremental deployment and allows a quick upgrade path to LISP. For larger sites with many external connections, distributed in geographically diverse PoPs, and complex internal topology, it may however make more sense to both encapsulate and decapsulate as soon as possible, to benefit from the information in the IGP to choose the best path (see Section 2.3 for a discussion of this scenario). Another thing to consider when placing tunnel routers are MTU issues. Since encapsulating packets increases overhead, the MTU of the end- to-end path may decrease, when encapsulated packets need to travel over segments having close to minimum MTU. Some transit networks are known to provide larger MTU than the typical value of 1500 bytes of popular access technologies used at end hosts (e.g., IEEE 802.3 and 802.11). However, placing the LISP router connecting to such a network at the customer edge could possibly bring up MTU issues, depending on the link type to the provider as opposed to the following scenario. 2.2. Provider Edge The other location at the core-edge boundary for deploying LISP routers is at the Internet service provider edge. The main incentive for this case is that the customer does not have to upgrade the CE router(s), or change the configuration of any equipment. Encapsulation/decapsulation happens in the provider's network, which may be able to serve several customers with a single device. For large ISPs with many residential/business customers asking for LISP this can lead to important savings, since there is no need to upgrade the software (or hardware, if it's the case) at each client's location. Instead, they can upgrade the software (or hardware) on a few PE routers serving the customers. This scenario is depicted in Figure 2. Jakab, et al. Expires March 16, 2013 [Page 5] Internet-Draft LISP Deployment September 2012 +----------+ +------------------+ | ISP1 | | ISP2 | | | | | | +----+ | | +----+ +----+ | +--|xTR1|--+ +--|xTR2|--|xTR3|--+ +----+ +----+ +----+ | | | | | | +--<[LISP site]>---+-------+ Figure 2: xTR at the PE While this approach can make transition easy for customers and may be cheaper for providers, the LISP site looses one of the main benefits of LISP: ingress traffic engineering. Since the provider controls the ETRs, additional complexity would be needed to allow customers to modify their mapping entries. The problem is aggravated when the LISP site is multihomed. Consider the scenario in Figure 2: whenever a change to TE policies is required, the customer contacts both ISP1 and ISP2 to make the necessary changes on the routers (if they provide this possibility). It is however unlikely, that both ISPs will apply changes simultaneously, which may lead to inconsistent state for the mappings of the LISP site. Since the different upstream ISPs are usually competing business entities, the ETRs may even be configured to compete, either to attract all the traffic or to get no traffic. The former will happen if the customer pays per volume, the latter if the connectivity has a fixed price. A solution could be to have the mappings in the Map-Server(s), and have their operator give control over the entries to customer, much like in the Domain Name System at the time of this writing. Additionally, since xTR1, xTR2, and xTR3 are in different administrative domains, locator reachability information is unlikely to be exchanged among them, making it difficult to set Loc-Status- Bits correctly on encapsulated packets. Compared to the customer edge scenario, deploying LISP at the provider edge might have the advantage of diminishing potential MTU issues, because the tunnel router is closer to the core, where links typically have higher MTUs than edge network links. 2.3. Split ITR/ETR In a simple LISP deployment, xTRs are located at the border of the LISP site (see Section 2.1). In this scenario packets are routed inside the domain according to the EID. However, more complex Jakab, et al. Expires March 16, 2013 [Page 6] Internet-Draft LISP Deployment September 2012 networks may want to route packets according to the destination RLOC. This would enable them to choose the best egress point. The LISP specification separates the ITR and ETR functionality and considers that both entities can be deployed in separated network equipment. ITRs can be deployed closer to the host (i.e., access routers). This way packets are encapsulated as soon as possible, and packets exit the network through the best egress point in terms of BGP policy. In turn, ETRs can be deployed at the border routers of the network, and packets are decapsulated as soon as possible. Once decapsulated, packets are routed based on destination EID, according to internal routing policy. In the following figure we can see an example. The Source (S) transmits packets using its EID and in this particular case packets are encapsulated at ITR_1. The encapsulated packets are routed inside the domain according to the destination RLOC, and can egress the network through the best point (i.e., closer to the RLOC's AS). On the other hand, inbound packets are received by ETR_1 which decapsulates them. Then packets are routed towards S according to the EID, again following the best path. +---------------------------------------+ | | | +-------+ +-------+ +-------+ | | ITR_1 |---------+ | ETR_1 |-RLOC_A--| ISP_A | | +-------+ | +-------+ +-------+ | +-+ | | | | |S| | IGP | | | +-+ | | | | +-------+ | +-------+ +-------+ | | ITR_2 |---------+ | ETR_2 |-RLOC_B--| ISP_B | | +-------+ +-------+ +-------+ | | +---------------------------------------+ Figure 3: Split ITR/ETR Scenario This scenario has a set of implications: o The site must carry at least partial BGP routes in order to choose the best egress point, increasing the complexity of the network. However, this is usually already the case for LISP sites that would benefit from this scenario. o If the site is multihomed to different ISPs and any of the upstream ISPs is doing uRPF filtering, this scenario may become impractical. ITRs need to determine the exit ETR, for setting the Jakab, et al. Expires March 16, 2013 [Page 7] Internet-Draft LISP Deployment September 2012 correct source RLOC in the encapsulation header. This adds complexity and reliability concerns. o In LISP, ITRs set the reachability bits when encapsulating data packets. Hence, ITRs need a mechanism to be aware of the liveness of all ETRs serving their site. o MTU within the site network must be large enough to accommodate encapsulated packets. o In this scenario, each ITR is serving fewer hosts than in the case when it is deployed at the border of the network. It has been shown that cache hit ratio grows logarithmically with the amount of users [cache]. Taking this into account, when ITRs are deployed closer to the host the effectiveness of the mapping cache may be lower (i.e., the miss ratio is higher). Another consequence of this is that the site may transmit a higher amount of Map-Requests, increasing the load on the distributed mapping database. 2.4. Inter-Service Provider Traffic Engineering With LISP, two LISP sites can route packets among them and control their ingress TE policies. Typically, LISP is seen as applicable to stub networks, however the LISP protocol can also be applied to transit networks recursively. Consider the scenario depicted in Figure 4. Packets originating from the LISP site Stub1, client of ISP_A, with destination Stub4, client of ISP_B, are LISP encapsulated at their entry point into the ISP_A's network. The external IP header now has as the source RLOC an IP from ISP_A's address space and destination RLOC from ISP_B's address space. One or more ASes separate ISP_A from ISP_B. With a single level of LISP encapsulation, Stub4 has control over its ingress traffic. However, at the time of this writing, ISP_B has only BGP tools (such as prefix deaggregation) to control on which of his own upstream or peering links should packets enter. This is either not feasible (if fine-grained per-customer control is required, the very specific prefixes may not be propagated) or increases DFZ table size. _.--. Stub1 ... +-------+ ,-'' `--. +-------+ ... Stub3 \ | R_A1|----,' `. ---|R_B1 | / --| R_A2|---( Transit ) | |-- Stub2 .../ | R_A3|-----. ,' ---|R_B2 | \... Stub4 +-------+ `--. _.-' +-------+ ... ISP_A `--'' ISP_B ... Jakab, et al. Expires March 16, 2013 [Page 8] Internet-Draft LISP Deployment September 2012 Figure 4: Inter-Service provider TE scenario A solution for this is to apply LISP recursively. ISP_A and ISP_B may reach a bilateral agreement to deploy their own private mapping system. ISP_A then encapsulates packets destined for the prefixes of ISP_B, which are listed in the shared mapping system. Note that in this case the packet is double-encapsulated (using R_A1, R_A2 or R_A3 as source and R_B1 or R_B2 as destination in the example above). ISP_B's ETR removes the outer, second layer of LISP encapsulation from the incoming packet, and routes it towards the original RLOC, the ETR of Stub4, which does the final decapsulation. If ISP_A and ISP_B agree to share a private distributed mapping database, both can control their ingress TE without the need of deaggregating prefixes. In this scenario the private database contains RLOC-to-RLOC bindings. The convergence time on the TE policies updates is expected to be fast, since ISPs only have to update/query a mapping to/from the database. This deployment scenario includes two important caveats. First, it is intended to be deployed between only two ISPs (ISP_A and ISP_B in Figure 4). If more than two ISPs use this approach, then the xTRs deployed at the participating ISPs must either query multiple mapping systems, or the ISPs must agree on a common shared mapping system. Second, the scenario is only recommended for ISPs providing connectivity to LISP sites, such that source RLOCs of packets to be reencapsulated belong to said ISP. Otherwise the participating ISPs must register prefixes they do not own in the above mentioned private mapping system. Failure to follow these recommendations may lead to operational and security issues when deploying this scenario. Besides these recommendations, the main disadvantages of this deployment case are: o Extra LISP header is needed. This increases the packet size and requires that the MTU between both ISPs accommodates double- encapsulated packets. o The ISP ITR must encapsulate packets and therefore must know the RLOC-to-RLOC binding. These bindings are stored in a mapping database and may be cached in the ITR's mapping cache. Cache misses lead to an additional lookup latency, unless a push based mapping system is used for the private mapping system. o The operational overhead of maintaining the shared mapping database. Jakab, et al. Expires March 16, 2013 [Page 9] Internet-Draft LISP Deployment September 2012 o If an IPv6 address block is reserved for EID use, as specified in [I-D.ietf-lisp-eid-block], the EID-to-RLOC encapsulation (first level) can avoid LISP processing altogether for non-LISP destinations. The ISP tunnel routers however will not be able to take advantage of this optimization, all RLOC-to-RLOC mappings need a lookup in the private database (or map-cache, once results are cached). 2.5. Tunnel Routers Behind NAT NAT in this section refers to IPv4 network address and port translation. 2.5.1. ITR Packets encapsulated by an ITR are just UDP packets from a NAT device's point of view, and they are handled like any UDP packet, there are no additional requirements for LISP data packets. Map-Requests sent by an ITR, which create the state in the NAT table, have a different 5-tuple in the IP header than the Map-Reply generated by the authoritative ETR. Since the source address of this packet is different from the destination address of the request packet, no state will be matched in the NAT table and the packet will be dropped. To avoid this, the NAT device has to do the following: o Send all UDP packets with source port 4342, regardless of the destination port, to the RLOC of the ITR. The most simple way to achieve this is configuring 1:1 NAT mode from the external RLOC of the NAT device to the ITR's RLOC (Called "DMZ" mode in consumer broadband routers). o Rewrite the ITR-AFI and "Originating ITR RLOC Address" fields in the payload. This setup supports a single ITR behind the NAT device. 2.5.2. ETR An ETR placed behind NAT is reachable from the outside by the Internet-facing locator of the NAT device. It needs to know this locator (and configure a loopback interface with it), so that it can use it in Map-Reply and Map-Register messages. Thus support for dynamic locators for the mapping database is needed in LISP equipment. Again, only one ETR behind the NAT device is supported. Jakab, et al. Expires March 16, 2013 [Page 10] Internet-Draft LISP Deployment September 2012 An implication of the issues described above is that LISP sites with xTRs can not be behind carrier based NATs, since two different sites would collide on the port forwarding. 2.6. Summary and Feature Matrix Feature CE PE Split Rec. -------------------------------------------------------- Control of ingress TE x - x x No modifications to existing int. network infrastructure x x - - Loc-Status-Bits sync x - x x MTU/PMTUD issues minimized - x - x 3. Map-Resolvers and Map-Servers 3.1. Map-Servers The Map-Server learns EID-to-RLOC mapping entries from an authoritative source and publishes them in the distributed mapping database. These entries are learned through authenticated Map- Register messages sent by authoritative ETRs. Also, upon reception of a Map-Request, the Map-Server verifies that the destination EID matches an EID-prefix for which it is authoritative for, and then re- encapsulates and forwards it to a matching ETR. Map-Server functionality is described in detail in [I-D.ietf-lisp-ms]. The Map-Server is provided by a Mapping Service Provider (MSP). A MSP can be any of the following: o EID registrar. Since the IPv4 address space is nearing exhaustion, IPv4 EIDs will come from already allocated Provider Independent (PI) space. The registrars in this case remain the current five Regional Internet Registries (RIRs). In the case of IPv6, the possibility of reserving a /16 block as EID space is currently under consideration [I-D.ietf-lisp-eid-block]. If granted by IANA, the community will have to determine the body responsible for allocations from this block, and the associated policies. Existing allocation policies apply to EIDs outside this block. o Third parties. Participating in the LISP mapping system is similar to participating in global routing or DNS: as long as there is at least another already participating entity willing to forward the newcomer's traffic, there is no barrier to entry. Still, just like routing and DNS, LISP mappings have the issue of trust, with efforts underway to make the published information Jakab, et al. Expires March 16, 2013 [Page 11] Internet-Draft LISP Deployment September 2012 verifiable. When these mechanisms will be deployed in the LISP mapping system, the burden of providing and verifying trust should be kept away from MSPs, which will simply host the secured mappings. This will keep the low barrier of entry to become an MSP for third parties. In all cases, the MSP configures its Map-Server(s) to publish the prefixes of its clients in the distributed mapping database and start encapsulating and forwarding Map-Requests to the ETRs of the AS. These ETRs register their prefix(es) with the Map-Server(s) through periodic authenticated Map-Register messages. In this context, for some LISP end sites, there is a need for mechanisms to: o Automatically distribute EID prefix(es) shared keys between the ETRs and the EID-registrar Map-Server. o Dynamically obtain the address of the Map-Server in the ETR of the AS. The Map-Server plays a key role in the reachability of the EID- prefixes it is serving. On the one hand it is publishing these prefixes into the distributed mapping database and on the other hand it is encapsulating and forwarding Map-Requests to the authoritative ETRs of these prefixes. ITRs encapsulating towards EIDs under the responsibility of a failed Map-Server will be unable to look up any of their covering prefixes. The only exception are the ITRs that already contain the mappings in their local cache. In this case ITRs can reach ETRs until the entry expires (typically 24 hours). For this reason, redundant Map-Server deployments are desirable. A set of Map-Servers providing high-availability service to the same set of prefixes is called a redundancy group. ETRs are configured to send Map-Register messages to all Map-Servers in the redundancy group. To achieve fail-over (or load-balancing, if desired), known mapping system specific best practices should be used. Additionally, if a Map-Server has no reachability for any ETR serving a given EID block, it should not originate that block into the mapping system. 3.2. Map-Resolvers A Map-Resolver a is a network infrastructure component which accepts LISP encapsulated Map-Requests, typically from an ITR, and finds the appropriate EID-to-RLOC mapping by either consulting its local cache or by consulting the distributed mapping database. Map-Resolver functionality is described in detail in [I-D.ietf-lisp-ms]. Anyone with access to the distributed mapping database can set up a Jakab, et al. Expires March 16, 2013 [Page 12] Internet-Draft LISP Deployment September 2012 Map-Resolver and provide EID-to-RLOC mapping lookup service. Database access setup is mapping system specific. For performance reasons, it is recommended that LISP sites use Map- Resolvers that are topologically close to their ITRs. ISPs supporting LISP will provide this service to their customers, possibly restricting access to their user base. LISP sites not in this position can use open access Map-Resolvers, if available. However, regardless of the availability of open access resolvers, the MSP providing the Map-Server(s) for a LISP site should also make available Map-Resolver(s) for the use of that site. In medium to large-size ASes, ITRs must be configured with the RLOC of a Map-Resolver, operation which can be done manually. However, in Small Office Home Office (SOHO) scenarios a mechanism for autoconfiguration should be provided. One solution to avoid manual configuration in LISP sites of any size is the use of anycast RLOCs for Map-Resolvers similar to the DNS root server infrastructure. Since LISP uses UDP encapsulation, the use of anycast would not affect reliability. LISP routers are then shipped with a preconfigured list of well know Map-Resolver RLOCs, which can be edited by the network administrator, if needed. The use of anycast also helps improving mapping lookup performance. Large MSPs can increase the number and geographical diversity of their Map-Resolver infrastructure, using a single anycasted RLOC. Once LISP deployment is advanced enough, very large content providers may also be interested running this kind of setup, to ensure minimal connection setup latency for those connecting to their network from LISP sites. While Map-Servers and Map-Resolvers implement different functionalities within the LISP mapping system, they can coexist on the same device. For example, MSPs offering both services, can deploy a single Map-Resolver/Map-Server in each PoP where they have a presence. 4. Proxy Tunnel Routers 4.1. P-ITR Proxy Ingress Tunnel Routers (P-ITRs) are part of the non-LISP/LISP transition mechanism, allowing non-LISP sites to reach LISP sites. They announce via BGP certain EID prefixes (aggregated, whenever possible) to attract traffic from non-LISP sites towards EIDs in the covered range. They do the mapping system lookup, and encapsulate Jakab, et al. Expires March 16, 2013 [Page 13] Internet-Draft LISP Deployment September 2012 received packets towards the appropriate ETR. Note that for the reverse path LISP sites can reach non-LISP sites simply by not encapsulating traffic. See [I-D.ietf-lisp-interworking] for a detailed description of P-ITR functionality. The success of new protocols depends greatly on their ability to maintain backwards compatibility and inter-operate with the protocol(s) they intend to enhance or replace, and on the incentives to deploy the necessary new software or equipment. A LISP site needs an interworking mechanism to be reachable from non-LISP sites. A P-ITR can fulfill this role, enabling early adopters to see the benefits of LISP, similar to tunnel brokers helping the transition from IPv4 to IPv6. A site benefits from new LISP functionality (proportionally with existing global LISP deployment) when going LISP, so it has the incentives to deploy the necessary tunnel routers. In order to be reachable from non-LISP sites it has two options: keep announcing its prefix(es) with BGP, or have a P-ITR announce prefix(es) covering them. If the goal of reducing the DFZ routing table size is to be reached, the second option is preferred. Moreover, the second option allows LISP-based ingress traffic engineering from all sites. However, the placement of P-ITRs significantly influences performance and deployment incentives. Section 5 is dedicated to the migration to a LISP-enabled Internet, and includes deployment scenarios for P-ITRs. 4.2. P-ETR In contrast to P-ITRs, P-ETRs are not required for the correct functioning of all LISP sites. There are two cases, where they can be of great help: o LISP sites with unicast reverse path forwarding (uRPF) restrictions, and o Communication between sites using different address family RLOCs. In the first case, uRPF filtering is applied at their upstream PE router. When forwarding traffic to non-LISP sites, an ITR does not encapsulate packets, leaving the original IP headers intact. As a result, packets will have EIDs in their source address. Since we are discussing the transition period, we can assume that a prefix covering the EIDs belonging to the LISP site is advertised to the global routing tables by a P-ITR, and the PE router has a route towards it. However, the next hop will not be on the interface towards the CE router, so non-encapsulated packets will fail uRPF checks. Jakab, et al. Expires March 16, 2013 [Page 14] Internet-Draft LISP Deployment September 2012 To avoid this filtering, the affected ITR encapsulates packets towards the locator of the P-ETR for non-LISP destinations. Now the source address of the packets, as seen by the PE router is the ITR's locator, which will not fail the uRPF check. The P-ETR then decapsulates and forwards the packets. The second use case is IPv4-to-IPv6 transition. Service providers using older access network hardware, which only supports IPv4 can still offer IPv6 to their clients, by providing a CPE device running LISP, and P-ETR(s) for accessing IPv6-only non-LISP sites and LISP sites, with IPv6-only locators. Packets originating from the client LISP site for these destinations would be encapsulated towards the P-ETR's IPv4 locator. The P-ETR is in a native IPv6 network, decapsulating and forwarding packets. For non-LISP destination, the packet travels natively from the P-ETR. For LISP destinations with IPv6-only locators, the packet will go through a P-ITR, in order to reach its destination. For more details on P-ETRs see the [I-D.ietf-lisp-interworking] draft. P-ETRs can be deployed by ISPs wishing to offer value-added services to their customers. As is the case with P-ITRs, P-ETRs too may introduce path stretch. Because of this the ISP needs to consider the tradeoff of using several devices, close to the customers, to minimize it, or few devices, farther away from the customers, minimizing cost instead. Since the deployment incentives for P-ITRs and P-ETRs are different, it is likely they will be deployed in separate devices, except for the CDN case, which may deploy both in a single device. In all cases, the existence of a P-ETR involves another step in the configuration of a LISP router. CPE routers, which are typically configured by DHCP, stand to benefit most from P-ETRs. Autoconfiguration of the P-ETR locator could be achieved by a DHCP option, or adding a P-ETR field to either Map-Notifys or Map-Replies. As a security measure, access to P-ETRs should be limited to legitimate users by enforcing ACLs. 5. Migration to LISP This section discusses a deployment architecture to support the migration to a LISP-enabled Internet. The loosely defined terms of "early transition phase", "late transition phase", and "LISP Internet phase" refer to time periods when LISP sites are a minority, a Jakab, et al. Expires March 16, 2013 [Page 15] Internet-Draft LISP Deployment September 2012 majority, or represent all edge networks respectively. 5.1. LISP+BGP For sites wishing to go LISP with their PI prefix the least disruptive way is to upgrade their border routers to support LISP, register the prefix into the LISP mapping system, but keep announcing it with BGP as well. This way LISP sites will reach them over LISP, while legacy sites will be unaffected by the change. The main disadvantage of this approach is that no decrease in the DFZ routing table size is achieved. Still, just increasing the number of LISP sites is an important gain, as an increasing LISP/non-LISP site ratio will slowly decrease the need for BGP-based traffic engineering that leads to prefix deaggregation. That, in turn, may lead to a decrease in the DFZ size in the late transition phase. This scenario is not limited to sites that already have their prefixes announced with BGP. Newly allocated EID blocks could follow this strategy as well during the early LISP deployment phase, depending on the cost/benefit analysis of the individual networks. Since this leads to an increase in the DFZ size, the following architecture should be preferred for new allocations. 5.2. Mapping Service Provider (MSP) P-ITR Service In addition to publishing their clients' registered prefixes in the mapping system, MSPs with enough transit capacity can offer them P-ITR service as a separate service. This service is especially useful for new PI allocations, to sites without existing BGP infrastructure, that wish to avoid BGP altogether. The MSP announces the prefix into the DFZ, and the client benefits from ingress traffic engineering without prefix deaggregation. The downside of this scenario is adding path stretch. Routing all non-LISP ingress traffic through a third party which is not one of its ISPs is only feasible for sites with modest amounts of traffic (like those using the IPv6 tunnel broker services today), especially in the first stage of the transition to LISP, with a significant number of legacy sites. When the LISP/non-LISP site ratio becomes high enough, this approach can prove increasingly attractive. Compared to LISP+BGP, this approach avoids DFZ bloat caused by prefix deaggregation for traffic engineering purposes, resulting in slower routing table increase in the case of new allocations and potential decrease for existing ones. Moreover, MSPs serving different clients with adjacent aggregable prefixes may lead to additional decrease, but quantifying this decrease is subject to future research study. Jakab, et al. Expires March 16, 2013 [Page 16] Internet-Draft LISP Deployment September 2012 5.3. Proxy-ITR Route Distribution (PITR-RD) Instead of a LISP site, or the MSP, announcing their EIDs with BGP to the DFZ, this function can be outsourced to a third party, a P-ITR Service Provider (PSP). This will result in a decrease of the operational complexity both at the site and at the MSP. The PSP manages a set of distributed P-ITR(s) that will advertise the corresponding EID prefixes through BGP to the DFZ. These P-ITR(s) will then encapsulate the traffic they receive for those EIDs towards the RLOCs of the LISP site, ensuring their reachability from non-LISP sites. While it is possible for a PSP to manually configure each client's EID routes to be announced, this approach offers little flexibility and is not scalable. This section presents a scalable architecture that offers automatic distribution of EID routes to LISP sites and service providers. The architecture requires no modification to existing LISP network elements, but it introduces a new (conceptual) network element, the EID Route Server, defined as a router that either propagates routes learned from other EID Route Servers, or it originates EID Routes. The EID-Routes that it originates are those that it is authoritative for. It propagates these routes to Proxy-ITRs within the AS of the EID Route Server. It is worth to note that a BGP capable router can be also considered as an EID Route Server. Further, an EID-Route is defined as a prefix originated via the Route Server of the mapping service provider, which should be aggregated if the MSP has multiple customers inside a single netblock. This prefix is propagated to other P-ITRs both within the MSP and to other P-ITR operators it peers with. EID Route Servers are operated either by the LISP site, MSPs or PSPs, and they may be collocated with a Map- Server or P-ITR, but are a functionally discrete entity. They distribute EID-Routes, using BGP, to other domains, according to policies set by participants. Jakab, et al. Expires March 16, 2013 [Page 17] Internet-Draft LISP Deployment September 2012 MSP (AS64500) RS ---> P-ITR | / | _.--./ ,-'' /`--. LISP site ---,' | v `. ( | DFZ )----- Mapping system non-LISP site ----. | ^ ,' `--. / _.-' | `--'' v / P-ITR PSP (AS64501) Figure 5: The P-ITR Route Distribution architecture The architecture described above decouples EID origination from route propagation, with the following benefits: o Can accurately represent business relationships between P-ITR operators o More mapping system agnostic o Minor changes to P-ITR implementation, no changes to other components In the example in the figure we have a MSP providing services to the LISP site. The LISP site does not run BGP, and gets an EID allocation directly from a RIR, or from the MSP, who may be a LIR. Existing PI allocations can be migrated as well. The MSP ensures the presence of the prefix in the mapping system, and runs an EID Route Server to distribute it to P-ITR service providers. Since the LISP site does not run BGP, the prefix will be originated with the AS number of the MSP. In the simple case depicted in Figure 5 the EID-Route of LISP Site will be originated by the Route Server, and announced to the DFZ by the PSP's P-ITRs with AS path 64501 64500. From that point on, the usual BGP dynamics apply. This way, routes announced by P-ITR are still originated by the authoritative Route Server. Note that the peering relationships between MSP/PSPs and those in the underlying forwarding plane may not be congruent, making the AS path to a P-ITR shorter than it is in reality. The non-LISP site will select the best path towards the EID-prefix, according to its local BGP policies. Since AS-path length is usually an important metric for selecting paths, a careful placement of P-ITR Jakab, et al. Expires March 16, 2013 [Page 18] Internet-Draft LISP Deployment September 2012 could significantly reduce path-stretch between LISP and non-LISP sites. The architecture allows for flexible policies between MSP/PSPs. Consider the EID Route Server networks as control plane overlays, facilitating the implementation of policies necessary to reflect the business relationships between participants. The results are then injected to the common underlying forwarding plane. For example, some MSP/PSPs may agree to exchange EID-Prefixes and only announce them to each of their forwarding plane customers. Global reachability of an EID-prefix depends on the MSP the LISP site buys service from, and is also subject to agreement between the mentioned parties. In terms of impact on the DFZ, this architecture results in a slower routing table increase for new allocations, since traffic engineering will be done at the LISP level. For existing allocations migrating to LISP, the DFZ may decrease since MSPs may be able to aggregate the prefixes announced. Compared to LISP+BGP, this approach avoids DFZ bloat caused by prefix deaggregation for traffic engineering purposes, resulting in slower routing table increase in the case of new allocations and potential decrease for existing ones. Moreover, MSPs serving different clients with adjacent aggregable prefixes may lead to additional decrease, but quantifying this decrease is subject to future research study. The flexibility and scalability of this architecture does not come without a cost however: A PSP operator has to establish either transit or peering relationships to improve their connectivity. 5.4. Migration Summary The following table presents the expected effects of the different transition scenarios during a certain phase on the DFZ routing table size: Phase | LISP+BGP | MSP P-ITR | PITR-RD -----------------+--------------+-----------------+---------------- Early transition | no change | slower increase | slower increase Late transition | may decrease | slower increase | slower increase LISP Internet | considerable decrease It is expected that PITR-RD will co-exist with LISP+BGP during the migration, with the latter being more popular in the early transition phase. As the transition progresses and the MSP P-ITR and PITR-RD ecosystem gets more ubiquitous, LISP+BGP should become less attractive, slowing down the increase of the number of routes in the Jakab, et al. Expires March 16, 2013 [Page 19] Internet-Draft LISP Deployment September 2012 DFZ. 6. Step-by-Step Example BGP to LISP Migration Procedure 6.1. Customer Pre-Install and Pre-Turn-up Checklist 1. Determine how many current physical service provider connections the customer has and their existing bandwidth and traffic engineering requirements. This information will determine the number of routing locators, and the priorities and weights that should be configured on the xTRs. 2. Make sure customer router has LISP capabilities. * Obtain output of 'show version' from the CE router. This information can be used to determine if the platform is appropriate to support LISP, in order to determine if a software and/or hardware upgrade is required. * Have customer upgrade (if necessary, software and/or hardware) to be LISP capable. 3. Obtain current running configuration of CE router. A suggested LISP router configuration example can be customized to the customer's existing environment. 4. Verify MTU Handling * Request increase in MTU to (1556) on service provider connections. Prior to MTU change verify that 1500 byte packet from P-xTR to RLOC with do not fragment (DF-bit) bit set. * Ensure they are not filtering ICMP unreachable or time- exceeded on their firewall or router. LISP, like any tunneling protocol, will increase the size of packets when the LISP header is appended. If increasing the MTU of the access links is not possible, care must be taken that ICMP is not being filtered in order to allow for Path MTU Discovery to take place. 5. Validate member prefix allocation. This step is to check if the prefix used by the customer is a Jakab, et al. Expires March 16, 2013 [Page 20] Internet-Draft LISP Deployment September 2012 direct (Provider Independent), or if it is a prefix assigned by a physical service provider (Provider Allocated). If the prefixes are assigned by other service provivers then a Letter of Agreement is required to announce prefixes through the Proxy Service Provider. 6. Verify the member RLOCs and their reachability. This step ensures that the RLOCs configured on the CE router are in fact reachable and working. 7. Prepare for cut-over. * If possible, have a host outside of all security and filtering policies connected to the console port of the edge router or switch. * Make sure customer has access to the router in order to configure it. 6.2. Customer Activating LISP Service 1. Customer configures LISP on CE router(s) from service provider recommended configuration. The LISP configuration consists of the EID prefix, the locators, and the weights and priorities of the mapping between the two values. In addition, the xTR must be configured with Map- Resolver(s), Map-Server(s) and the shared key for registering to Map-Server(s). If required, Proxy-ETR(s) may be configured as well. In addition to the LISP configuration, the following: * Ensure default route(s) to next-hop external neighbors are included and RLOCs are present in configuration. * If two or more routers are used, ensure all RLOCs are included in the LISP configuration on all routers. * It will be necessary to redistribute default route via IGP between the external routers. 2. When transition is ready perform a soft shutdown on existing eBGP peer session(s) * From CE router, use LIG to ensure registration is successful. Jakab, et al. Expires March 16, 2013 [Page 21] Internet-Draft LISP Deployment September 2012 * To verify LISP connectivity, ping LISP connected sites. See http://www.lisp4.net/ and/or http://www.lisp6.net/ for potential candidates. * To verify connectivity to non-LISP sites, try accessing major Internet sites via a web browser. 6.3. Cut-Over Provider Preparation and Changes 1. Verify site configuration and then active registration on Map- Server(s) * Authentication key * EID prefix 2. Add EID space to map-cache on proxies 3. Add networks to BGP advertisement on proxies * Modify route-maps/policies on P-xTRs * Modify route policies on core routers (if non-connected member) * Modify ingress policers on core routers * Ensure route announcement in looking glass servers, RouteViews 4. Perform traffic verification test * Ensure MTU handling is as expected (PMTUD working) * Ensure proxy-ITR map-cache population * Ensure access from traceroute/ping servers around Internet * Use a looking glass, to check for external visibility of registration via several Map-Resolvers (e.g., http://lispmon.net/). 7. Security Considerations Security implications of LISP deployments are to be discussed in separate documents. [I-D.saucez-lisp-security] gives an overview of LISP threat models, while securing mapping lookups is discussed in [I-D.ietf-lisp-sec]. Jakab, et al. Expires March 16, 2013 [Page 22] Internet-Draft LISP Deployment September 2012 8. IANA Considerations This memo includes no request to IANA. 9. Acknowledgements Many thanks to Margaret Wasserman for her contribution to the IETF76 presentation that kickstarted this work. The authors would also like to thank Damien Saucez, Luigi Iannone, Joel Halpern, Vince Fuller, Dino Farinacci, Terry Manderson, Noel Chiappa, Hannu Flinck, and everyone else who provided input. 10. Informative References [I-D.ietf-lisp] Farinacci, D., Fuller, V., Meyer, D., and D. Lewis, "Locator/ID Separation Protocol (LISP)", draft-ietf-lisp-23 (work in progress), May 2012. [I-D.ietf-lisp-eid-block] Iannone, L., Lewis, D., Meyer, D., and V. Fuller, "LISP EID Block", draft-ietf-lisp-eid-block-02 (work in progress), April 2012. [I-D.ietf-lisp-interworking] Lewis, D., Meyer, D., Farinacci, D., and V. Fuller, "Interworking LISP with IPv4 and IPv6", draft-ietf-lisp-interworking-06 (work in progress), March 2012. [I-D.ietf-lisp-ms] Fuller, V. and D. Farinacci, "LISP Map Server Interface", draft-ietf-lisp-ms-16 (work in progress), March 2012. [I-D.ietf-lisp-sec] Maino, F., Ermagan, V., Cabellos-Aparicio, A., Saucez, D., and O. Bonaventure, "LISP-Security (LISP-SEC)", draft-ietf-lisp-sec-02 (work in progress), March 2012. [I-D.saucez-lisp-security] Saucez, D., Iannone, L., and O. Bonaventure, "LISP Security Threats", draft-saucez-lisp-security-03 (work in progress), March 2011. [cache] Jung, J., Sit, E., Balakrishnan, H., and R. Morris, "DNS performance and the effectiveness of caching", 2002. Jakab, et al. Expires March 16, 2013 [Page 23] Internet-Draft LISP Deployment September 2012 Authors' Addresses Lorand Jakab Technical University of Catalonia C/Jordi Girona, s/n BARCELONA 08034 Spain Email: ljakab@ac.upc.edu Albert Cabellos-Aparicio Technical University of Catalonia C/Jordi Girona, s/n BARCELONA 08034 Spain Email: acabello@ac.upc.edu Florin Coras Technical University of Catalonia C/Jordi Girona, s/n BARCELONA 08034 Spain Email: fcoras@ac.upc.edu Jordi Domingo-Pascual Technical University of Catalonia C/Jordi Girona, s/n BARCELONA 08034 Spain Email: jordi.domingo@ac.upc.edu Darrel Lewis Cisco Systems 170 Tasman Drive San Jose, CA 95134 USA Email: darlewis@cisco.com Jakab, et al. Expires March 16, 2013 [Page 24]