TOC 
Network Working GroupJ. Schoenwaelder
Internet-DraftJacobs University Bremen
Intended status: Standards TrackA. Clemm
Expires: February 7, 2010A. Karmakar
 Cisco Systems
 August 06, 2009


Definitions of Managed Objects for Mapping SYSLOG Messages to Simple Network Management Protocol (SNMP) Notifications
draft-ietf-opsawg-syslog-msg-mib-05.txt

Status of this Memo

This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as “work in progress.”

The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt.

The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html.

This Internet-Draft will expire on February 7, 2010.

Copyright Notice

Copyright (c) 2009 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents in effect on the date of publication of this document (http://trustee.ietf.org/license-info). Please review these documents carefully, as they describe your rights and restrictions with respect to this document.

Abstract

This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it defines a mapping of SYSLOG messages to Simple Network Management Protocol (SNMP) notifications.



Table of Contents

1.  Introduction
2.  The Internet-Standard Management Framework
3.  Conventions
4.  Overview
5.  Relationship to Other MIB Modules
6.  Relationship to the SNMP Notification to SYSLOG Mapping
7.  Definitions
8.  Usage Example
9.  IANA Considerations
10.  Security Considerations
11.  Acknowledgments
12.  References
    12.1.  Normative References
    12.2.  Informative References
§  Authors' Addresses




 TOC 

1.  Introduction

SNMP [RFC3410] (Case, J., Mundy, R., Partain, D., and B. Stewart, “Introduction and Applicability Statements for Internet-Standard Management Framework,” December 2002.) [RFC3411] (Harrington, D., Presuhn, R., and B. Wijnen, “An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks,” December 2002.) and SYSLOG [RFC5424] (Gerhards, R., “The Syslog Protocol,” March 2009.) are two widely used protocols to communicate event notifications. Although co-existence of several management protocols in one operational environment is possible, certain environments require that all event notifications are collected by a single system daemon such as a SYSLOG collector or an SNMP notification receiver via a single management protocol. In such environments, it is necessary to translate event notifications between management protocols.

This document defines an SNMP MIB module to represent SYSLOG messages and to send SYSLOG messages as SNMP notifications to SNMP notification receivers.



 TOC 

2.  The Internet-Standard Management Framework

For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410] (Case, J., Mundy, R., Partain, D., and B. Stewart, “Introduction and Applicability Statements for Internet-Standard Management Framework,” December 2002.)

Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578] (McCloghrie, K., Perkins, D., and J. Schoenwaelder, “Structure of Management Information Version 2 (SMIv2),” April 1999.), STD 58, RFC 2579 [RFC2579] (McCloghrie, K., Perkins, D., and J. Schoenwaelder, “Textual Conventions for SMIv2,” April 1999.) and STD 58, RFC 2580 [RFC2580] (McCloghrie, K., Perkins, D., and J. Schoenwaelder, “Conformance Statements for SMIv2,” April 1999.) .



 TOC 

3.  Conventions

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119] (Bradner, S., “Key words for use in RFCs to Indicate Requirement Levels,” March 1997.).



 TOC 

4.  Overview

SYSLOG messages are translated to SNMP by a SYSLOG-to-SNMP translator. Such a translator acts as a SYSLOG collector [RFC5424] (Gerhards, R., “The Syslog Protocol,” March 2009.) and implements a MIB module according to the SNMP architecture [RFC3411] (Harrington, D., Presuhn, R., and B. Wijnen, “An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks,” December 2002.). The translator might be tightly coupled to an SNMP agent or it might interface with an SNMP agent via a subagent protocol.

After initialization, the SYSLOG-to-SNMP translator will listen for SYSLOG messages. On receiving a message, the message will be parsed to extract information as described in the MIB module. A conceptual table is populated with information extracted from the SYSLOG message and finally a notification may be generated.

The MIB module is organized into a group of scalars and two tables. The syslogMsgControl group contains two scalars controlling the maximum size of SYSLOG messages recorded in the tables and whether SNMP notifications are generated for SYSLOG messages.

--syslogMsgObjects(1)
  |
  +--syslogMsgControl(1)
     |
     +-- Unsigned32 syslogMsgTableMaxSize(1)
     +-- TruthValue syslogMsgEnableNotifications(2)

The syslogMsgTable contains one entry for each recorded SYSLOG message. The basic fields of SYSLOG messages as well as message properties are represented in different columns of the conceptual table.

--syslogMsgObjects(1)
  |
  +--syslogMsgTable(2)
     |
     +--syslogMsgEntry(1) [syslogMsgIndex]
        |
        +-- Unsigned32      syslogMsgIndex(1)
        +-- SyslogFacility  syslogMsgFacility(2)
        +-- SyslogSeverity  syslogMsgSeverity(3)
        +-- Unsigned32      syslogMsgVersion(4)
        +-- SyslogTimeStamp syslogMsgTimeStamp(5)
        +-- DisplayString   syslogMsgHostName(6)
        +-- DisplayString   syslogMsgAppName(7)
        +-- DisplayString   syslogMsgProcID(8)
        +-- DisplayString   syslogMsgMsgID(9)
        +-- Unsigned32      syslogMsgSDParams(10)
        +-- OctetString     syslogMsgMsg(11)

The syslogMsgSDTable contains one entry for each structured data element parameter contained in a SYSLOG message. Since structured data elements are optional, the relationship between the syslogMsgTable and the syslogMsgSDTable ranges from one-to-zero to one-to-many.

--syslogMsgObjects(1)
  |
  +--syslogMsgSDTable(3)
     |
     +--syslogMsgSDEntry(1) [syslogMsgIndex,
        |                    syslogMsgSDParamIndex,
        |                    syslogMsgSDID,
        |                    syslogMsgSDParamName]
        |
        +-- Unsigned32      syslogMsgSDParamIndex(1)
        +-- DisplayString   syslogMsgSDID(2)
        +-- DisplayString   syslogMsgSDParamName(3)
        +-- SnmpAdminString syslogMsgSDParamValue(4)


 TOC 

5.  Relationship to Other MIB Modules

The NOTIFICATION-LOG-MIB [RFC3014] (Kavasseri, R., Ed., “Notification Log MIB,” November 2002.) provides a generic mechanism for logging SNMP notifications in order to deal with lost SNMP notifications, e.g., due to transient communication problems. Applications can poll the notification log to verify that they have not missed important SNMP notifications.

The MIB module defined in this memo provides a mechanism for logging SYSLOG notifications. This additional SYSLOG notification log is provided because (a) SYSLOG messages might not lead to SNMP notification (this is configurable) and (b) SNMP notifications might not carry all information associated with a SYSLOG notification.

The MIB module IMPORTS objects from SNMPv2-SMI [RFC2578] (McCloghrie, K., Perkins, D., and J. Schoenwaelder, “Structure of Management Information Version 2 (SMIv2),” April 1999.), SNMPv2-TC [RFC2579] (McCloghrie, K., Perkins, D., and J. Schoenwaelder, “Textual Conventions for SMIv2,” April 1999.), SNMPv2-CONF [RFC2580] (McCloghrie, K., Perkins, D., and J. Schoenwaelder, “Conformance Statements for SMIv2,” April 1999.), SNMP-FRAMEWORK-MIB [RFC3411] (Harrington, D., Presuhn, R., and B. Wijnen, “An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks,” December 2002.), and SYSLOG-TC-MIB [RFC5427] (Keeni, G., “Textual Conventions for Syslog Management,” March 2009.).



 TOC 

6.  Relationship to the SNMP Notification to SYSLOG Mapping

A companion document defines a mapping of SNMP notifications to SYSLOG messages [I‑D.ietf‑opsawg‑syslog‑snmp] (Marinov, V. and J. Schoenwaelder, “Mapping Simple Network Management Protocol (SNMP) Notifications to SYSLOG Messages,” March 2009.). This section discusses the possibilities of using both specifications in combination.

A SYSLOG collector implementing the SYSLOG-MSG-MIB module and the mapping of SNMP notifications to SYSLOG messages may be configured to translate received SYSLOG messages containing SNMP notifications back into the original SNMP notification. In this case, the relevant tables of the SYSLOG-MSG-MIB will not be populated for SYSLOG messages carrying SNMP notifications. This configuration allows operators to build a forwarding chain where SNMP notifications are "tunneled" through SYSLOG messages. Due to size restrictions of the SYSLOG transports and the more verbose textual encoding used by SYSLOG, there is a possibility that SNMP notification content gets truncated while tunneled through SYSLOG and thus the resulting SNMP notification may be incomplete.

An SNMP management application supporting the SYSLOG-MSG-MIB and the mapping of SNMP notifications to SYSLOG messages may process information from the SYSLOG-MSG-MIB in order to emit a SYSLOG message representing the SYSLOG message recorded in the SYSLOG-MSG-MIB module. This configuration allows operators to build a forwarding chain where SYSLOG messages are "tunneled" through SNMP messages. A notification receiver can determine whether a syslogMsgNotification contained all structured data element parameters of a SYSLOG message. In case parameters are missing, a forwarding application MUST retrieve the missing parameters from the SYSLOG-MSG-MIB. Regular polling of the SYSLOG-MSG-MIB can be used to take care of any lost SNMP notifications.



 TOC 

7.  Definitions

SYSLOG-MSG-MIB DEFINITIONS ::= BEGIN

IMPORTS
    MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Unsigned32, mib-2
        FROM SNMPv2-SMI
    TEXTUAL-CONVENTION, DisplayString, TruthValue
        FROM SNMPv2-TC
    OBJECT-GROUP, NOTIFICATION-GROUP, MODULE-COMPLIANCE
        FROM SNMPv2-CONF
    SnmpAdminString
        FROM SNMP-FRAMEWORK-MIB
    SyslogFacility, SyslogSeverity
        FROM SYSLOG-TC-MIB;

syslogMsgMib MODULE-IDENTITY
    LAST-UPDATED "200908050800Z"
    ORGANIZATION "IETF OPSAWG Working Group"
    CONTACT-INFO
        "Juergen Schoenwaelder
         <j.schoenwaelder@jacobs-university.de>
         Jacobs University Bremen
         Campus Ring 1
         28757 Bremen
         Germany

         Alexander Clemm
         <alex@cisco.com>
         Cisco Systems
         170 West Tasman Drive
         San Jose, CA 95134-1706
         USA

         Anirban Karmakar
         <akarmaka@cisco.com>
         Cisco Systems
         170 West Tasman Drive
         San Jose, CA 95134-1706
         USA"
    DESCRIPTION
        "This MIB module represent SYSLOG messages as SNMP objects.

         Copyright (c) 2009 IETF Trust and the persons identified as
         the document authors.  All rights reserved.

         Redistribution and use in source and binary forms, with or
         without modification, are permitted provided that the
         following conditions are met:

         - Redistributions of source code must retain the above
           copyright notice, this list of conditions and the
           following disclaimer.

         - Redistributions in binary form must reproduce the above
           copyright notice, this list of conditions and the
           following disclaimer in the documentation and/or other
           materials provided with the distribution.

         - Neither the name of Internet Society, IETF or IETF
           Trust, nor the names of specific contributors, may be
           used to endorse or promote products derived from this
           software without specific prior written permission.

         THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
         CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED
         WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
         WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
         PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE COPYRIGHT
         OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
         INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
         (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
         GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
         BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
         LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
         (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
         OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
         POSSIBILITY OF SUCH DAMAGE.

         This version of this MIB module is part of RFC XXXX; see
         the RFC itself for full legal notices."
    REVISION "200908050800Z"
    DESCRIPTION
        "Initial version issued as part of RFC XXXX."
-- RFC Ed.: replace XXXX with actual RFC number & remove this note
    ::= { mib-2 XXX }
-- RFC Ed.: replace XXX with IANA-assigned number & remove this note

-- textual convention definitions

SyslogTimeStamp ::= TEXTUAL-CONVENTION
    DISPLAY-HINT "2d-1d-1d,1d:1d:1d.3d,1a1d:1d"
    STATUS       current
    DESCRIPTION
       "A date-time specification. This type is similar to the
        DateAndTime type defined in the SNMPv2-TC except that
        the subsecond granulation is microseconds instead of
        deciseconds and that a zero-length string can be used
        to indicate a missing value.

        field  octets  contents                  range
        -----  ------  --------                  -----
          1      1-2   year*                     0..65536
          2       3    month                     1..12
          3       4    day                       1..31
          4       5    hour                      0..23
          5       6    minutes                   0..59
          6       7    seconds                   0..60
                       (use 60 for leap-second)
          7     8-10   microseconds              0..999999
          8      11    direction from UTC        '+' / '-'
          9      12    hours from UTC*           0..13
         10      13    minutes from UTC          0..59

        * Notes:
        - the value of year is in network-byte order
        - the value of microseconds is in network-byte order
        - daylight saving time in New Zealand is +13

        For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be
        displayed as:

                        1992-5-26,13:30:15.0,-4:0

        Note that if only local time is known, then timezone
        information (fields 11-13) is not present."
    SYNTAX      OCTET STRING (SIZE (0 | 10 | 13))

-- object definitions

syslogMsgNotifications OBJECT IDENTIFIER ::= { syslogMsgMib 0 }
syslogMsgObjects       OBJECT IDENTIFIER ::= { syslogMsgMib 1 }
syslogMsgConformance   OBJECT IDENTIFIER ::= { syslogMsgMib 2 }

syslogMsgControl       OBJECT IDENTIFIER ::= { syslogMsgObjects 1 }

syslogMsgTableMaxSize OBJECT-TYPE
    SYNTAX      Unsigned32
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
       "The maximum number of syslog messages that may be held in
        syslogMsgTable.  A particular setting does not guarantee that
        there is sufficient memory available for the maximum number
        of table entries indicated by this object. A value of 0 means
        no limit.

        If an application reduces the limit while there are syslog
        messages in the syslogMsgTable, the syslog messages that are
        in the syslogMsgTable for the longest time MUST be discarded
        to bring the table down to the new limit.

        The value of this object should be kept in nonvolatile
        memory."
    DEFVAL      { 0 }
    ::= { syslogMsgControl 1 }

syslogMsgEnableNotifications OBJECT-TYPE
    SYNTAX      TruthValue
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
       "Indicates whether syslogMsgNotification notifications are
        generated.

        The value of this object should be kept in nonvolatile
        memory."
    DEFVAL      { false }
    ::= { syslogMsgControl 2 }

syslogMsgTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF SyslogMsgEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
       "A table containing recent syslog messages. The size of the
        table is controlled by the syslogMsgTableMaxSize object."
    ::= { syslogMsgObjects 2 }

syslogMsgEntry OBJECT-TYPE
    SYNTAX      SyslogMsgEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
       "An entry of the syslogMsgTable."
    INDEX { syslogMsgIndex }
    ::= { syslogMsgTable 1 }

SyslogMsgEntry ::= SEQUENCE {
    syslogMsgIndex      Unsigned32,
    syslogMsgFacility   SyslogFacility,
    syslogMsgSeverity   SyslogSeverity,
    syslogMsgVersion    Unsigned32,
    syslogMsgTimeStamp  SyslogTimeStamp,
    syslogMsgHostName   DisplayString,
    syslogMsgAppName    DisplayString,
    syslogMsgProcID     DisplayString,
    syslogMsgMsgID      DisplayString,
    syslogMsgSDParams   Unsigned32,
    syslogMsgMsg        OCTET STRING
}

syslogMsgIndex OBJECT-TYPE
    SYNTAX      Unsigned32 (1..4294967295)
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
       "A monotonically increasing number used to identify entries in
        the syslogMsgTable. When syslogMsgIndex reaches the maximum
        value the value wraps back to 1."
    ::= { syslogMsgEntry 1 }

syslogMsgFacility OBJECT-TYPE
    SYNTAX      SyslogFacility
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The facility of the syslog message."
    REFERENCE
       "RFC5424: The Syslog Protocol (section 6.2.1)
        RFC5427: Textual Conventions for Syslog Management"
    ::= { syslogMsgEntry 2 }

syslogMsgSeverity OBJECT-TYPE
    SYNTAX      SyslogSeverity
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The severity of the syslog message"
    REFERENCE
       "RFC5424: The Syslog Protocol (section 6.2.1)
        RFC5427: Textual Conventions for Syslog Management"
    ::= { syslogMsgEntry 3 }

syslogMsgVersion OBJECT-TYPE
    SYNTAX      Unsigned32 (0..999)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The version of the syslog message. A value of 0 indicates
        that the version is unknown."
    REFERENCE
       "RFC5424: The Syslog Protocol (section 6.2.2)"
    ::= { syslogMsgEntry 4 }

syslogMsgTimeStamp OBJECT-TYPE
    SYNTAX      SyslogTimeStamp
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The timestamp of the syslog message. A zero length
        string is returned if the timestamp is unknown."
    REFERENCE
       "RFC5424: The Syslog Protocol (section 6.2.3)"
    ::= { syslogMsgEntry 5 }

syslogMsgHostName OBJECT-TYPE
    SYNTAX      DisplayString (SIZE (0..255))
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The host name of the syslog message. A zero-length string
        indicates an unknown host name. The SYSLOG protocol
        specification constrains this string to printable US-ASCII
        code points."
    REFERENCE
       "RFC5424: The Syslog Protocol (section 6.2.4)"
    ::= { syslogMsgEntry 6 }

syslogMsgAppName OBJECT-TYPE
    SYNTAX      DisplayString (SIZE (0..48))
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The app-name of the syslog message. A zero-length string
        indicates an unknown app-name. The SYSLOG protocol
        specification constrains this string to printable US-ASCII
        code points."
    REFERENCE
       "RFC5424: The Syslog Protocol (section 6.2.5)"
    ::= { syslogMsgEntry 7 }

syslogMsgProcID OBJECT-TYPE
    SYNTAX      DisplayString (SIZE (0..128))
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The procid of the syslog message. A zero-length string
        indicates an unknown procid. The SYSLOG protocol specification
        constrains this string to printable US-ASCII code points."
    REFERENCE
       "RFC5424: The Syslog Protocol (section 6.2.6)"
    ::= { syslogMsgEntry 8 }

syslogMsgMsgID OBJECT-TYPE
    SYNTAX      DisplayString (SIZE (0..32))
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The msgid of the syslog message. A zero-length string
        indicates an unknown msgid. The SYSLOG protocol specification
        constrains this string to printable US-ASCII code points."
    REFERENCE
       "RFC5424: The Syslog Protocol (section 6.2.7)"
    ::= { syslogMsgEntry 9 }

syslogMsgSDParams OBJECT-TYPE
    SYNTAX      Unsigned32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The total number of structured data element parameters
        carried in the syslog message. This number effectively
        indicates the number of entries in the syslogMsgSDTable.
        It can be used, for example, by a notification receiver
        to determine whether a notification carried all
        structured data element parameters of a syslog message."
    ::= { syslogMsgEntry 10 }

syslogMsgMsg OBJECT-TYPE
    SYNTAX      OCTET STRING
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The message part of the syslog message. The syntax does not
        impose a size restriction. Implementations of this MIB module
        may truncate the message part of the syslog message such that
        it fits into the size constraints imposed by the implementation
        environment. Such truncations can also happen elsewhere in the
        syslog forwarding chain.

        If the first octets contain the value 'EFBBBF'h, then the rest
        of the message is a UTF-8 string. Since syslog messages may be
        truncated at arbitrary octet boundaries during forwarding, the
        message may contain invalid UTF-8 encodings at the end."
    REFERENCE
       "RFC5424: The Syslog Protocol (sections 6.1 and 6.4)"
    ::= { syslogMsgEntry 11 }

syslogMsgSDTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF SyslogMsgSDEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
       "A table containing structured data elements of syslog
        messages."
    ::= { syslogMsgObjects 3 }

syslogMsgSDEntry OBJECT-TYPE
    SYNTAX      SyslogMsgSDEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
       "An entry of the syslogMsgSDTable."
    INDEX { syslogMsgIndex, syslogMsgSDParamIndex,
            syslogMsgSDID, syslogMsgSDParamName }
    ::= { syslogMsgSDTable 1 }

SyslogMsgSDEntry ::= SEQUENCE {
    syslogMsgSDParamIndex  Unsigned32,
    syslogMsgSDID          DisplayString,
    syslogMsgSDParamName   DisplayString,
    syslogMsgSDParamValue  SnmpAdminString
}

syslogMsgSDParamIndex OBJECT-TYPE
    SYNTAX      Unsigned32 (1..4294967295)
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
       "This object indexes the structured data element parameters
        contained in a SYSLOG message. The first structured data
        element parameter has the index value 1 and subsequent
        parameters are indexed by incrementing the index of the
        previous parameter. The index increases across structured
        data element boundaries so that the value reflects the
        position of a structured data element parameter in a
        SYSLOG message."
    REFERENCE
       "RFC5424: The Syslog Protocol (section 6.3.3)"
    ::= { syslogMsgSDEntry 1 }

syslogMsgSDID OBJECT-TYPE
    SYNTAX      DisplayString (SIZE (1..32))
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
       "The name (SD-ID) of a structured data element. The SYSLOG
        protocol specification constrains this string to printable
        US-ASCII code points."
    REFERENCE
       "RFC5424: The Syslog Protocol (section 6.3.2)"
    ::= { syslogMsgSDEntry 2 }

syslogMsgSDParamName OBJECT-TYPE
    SYNTAX      DisplayString (SIZE (1..32))
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
       "The name of a parameter of the structured data element. The
        SYSLOG protocol specification constrains this string to
        printable US-ASCII code points."
    REFERENCE
       "RFC5424: The Syslog Protocol (section 6.3.3)"
    ::= { syslogMsgSDEntry 3 }

syslogMsgSDParamValue OBJECT-TYPE
    SYNTAX      SnmpAdminString
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
       "The value of the parameter of a syslog message identified by
        the index of this table. The value is stored in the unescaped
        format."
    REFERENCE
       "RFC5424: The Syslog Protocol (section 6.3.3)"
    ::= { syslogMsgSDEntry 4 }

-- notification definitions

syslogMsgNotification NOTIFICATION-TYPE
    OBJECTS     { syslogMsgFacility, syslogMsgSeverity,
                  syslogMsgVersion, syslogMsgTimeStamp,
                  syslogMsgHostName, syslogMsgAppName,
                  syslogMsgProcID, syslogMsgMsgID,
                  syslogMsgSDParams, syslogMsgMsg }
    STATUS      current
    DESCRIPTION
       "The syslogMsgNotification is generated when a new syslog
        message is received and the value of
        syslogMsgGenerateNotifications is true.

        Implementations may add syslogMsgSDParamValue objects as long
        as the resulting notification fits into the size constraints
        imposed by the implementation environment and the notification
        message size constraints imposed by maxMessageSize [RFC3412]
        and SNMP transport mappings."
    ::= { syslogMsgNotifications 1 }

-- conformance statements

syslogMsgGroups      OBJECT IDENTIFIER ::= { syslogMsgConformance 1 }
syslogMsgCompliances OBJECT IDENTIFIER ::= { syslogMsgConformance 2 }

syslogMsgFullCompliance MODULE-COMPLIANCE
    STATUS      current
    DESCRIPTION
       "The compliance statement for implementations of the
        SYSLOG-MSG-MIB."
    MODULE      -- this module
    MANDATORY-GROUPS {
        syslogMsgGroup,
        syslogMsgSDGroup,
        syslogMsgControlGroup,
        syslogMsgNotificationGroup
    }
    ::= { syslogMsgCompliances 1 }

syslogMsgReadOnlyCompliance MODULE-COMPLIANCE
    STATUS      current
    DESCRIPTION
       "The compliance statement for implementations of the
        SYSLOG-MSG-MIB that do not support read-write access."
    MODULE      -- this module
    MANDATORY-GROUPS {
        syslogMsgGroup,
        syslogMsgSDGroup,
        syslogMsgControlGroup,
        syslogMsgNotificationGroup
    }
    OBJECT syslogMsgTableMaxSize
       MIN-ACCESS  read-only
       DESCRIPTION
          "Write access is not required."
    OBJECT syslogMsgEnableNotifications
       MIN-ACCESS  read-only
       DESCRIPTION
          "Write access is not required."
    ::= { syslogMsgCompliances 2 }

syslogMsgNotificationCompliance MODULE-COMPLIANCE
    STATUS      current
    DESCRIPTION
       "The compliance statement for implementations of the
        SYSLOG-MSG-MIB that do only generate notifications and not
        provide a table to allow read access to syslog message
        details."
    MODULE      -- this module
    MANDATORY-GROUPS {
        syslogMsgGroup,
        syslogMsgSDGroup,
        syslogMsgNotificationGroup
    }
    OBJECT      syslogMsgFacility
    MIN-ACCESS  accessible-for-notify
    DESCRIPTION
        "Read access is not required."
    OBJECT      syslogMsgSeverity
    MIN-ACCESS  accessible-for-notify
    DESCRIPTION
       "Read access is not required."
    OBJECT      syslogMsgVersion
    MIN-ACCESS  accessible-for-notify
    DESCRIPTION
       "Read access is not required."
    OBJECT      syslogMsgTimeStamp
    MIN-ACCESS  accessible-for-notify
    DESCRIPTION
       "Read access is not required."
    OBJECT      syslogMsgHostName
    MIN-ACCESS  accessible-for-notify
    DESCRIPTION
       "Read access is not required."
    OBJECT      syslogMsgAppName
    MIN-ACCESS  accessible-for-notify
    DESCRIPTION
       "Read access is not required."
    OBJECT      syslogMsgProcID
    MIN-ACCESS  accessible-for-notify
    DESCRIPTION
       "Read access is not required."
    OBJECT      syslogMsgMsgID
    MIN-ACCESS  accessible-for-notify
    DESCRIPTION
       "Read access is not required."
    OBJECT      syslogMsgSDParams
    MIN-ACCESS  accessible-for-notify
    DESCRIPTION
       "Read access is not required."
    OBJECT      syslogMsgMsg
    MIN-ACCESS  accessible-for-notify
    DESCRIPTION
       "Read access is not required."
    OBJECT      syslogMsgSDParamValue
    MIN-ACCESS  accessible-for-notify
    DESCRIPTION
       "Read access is not required."
    ::= { syslogMsgCompliances 3 }

syslogMsgNotificationGroup NOTIFICATION-GROUP
    NOTIFICATIONS {
        syslogMsgNotification
    }
    STATUS      current
    DESCRIPTION
       "The notifications emitted by this MIB module."
    ::= { syslogMsgGroups 1 }

syslogMsgGroup OBJECT-GROUP
    OBJECTS {
        -- syslogMsgIndex,
        syslogMsgFacility,
        syslogMsgSeverity,
        syslogMsgVersion,
        syslogMsgTimeStamp,
        syslogMsgHostName,
        syslogMsgAppName,
        syslogMsgProcID,
        syslogMsgMsgID,
        syslogMsgSDParams,
        syslogMsgMsg
    }
    STATUS      current
    DESCRIPTION
       "A collection of objects representing a syslog message
        excluding structured data elements."
    ::= { syslogMsgGroups 2 }

syslogMsgSDGroup OBJECT-GROUP
    OBJECTS {
        -- syslogMsgSDParamIndex,
        -- syslogMsgSDID,
        -- syslogMsgSDParamName,
        syslogMsgSDParamValue
    }
    STATUS      current
    DESCRIPTION
       "A collection of objects representing the structured data
        elements of a syslog message."
    ::= { syslogMsgGroups 3 }

syslogMsgControlGroup OBJECT-GROUP
    OBJECTS {
        syslogMsgTableMaxSize,
        syslogMsgEnableNotifications
    }
    STATUS      current
    DESCRIPTION
       "A collection of control objects to control the size of the
        syslogMsgTable and to enable / disable notifications."
    ::= { syslogMsgGroups 4 }

END


 TOC 

8.  Usage Example

The following example shows a valid syslog message including structured data. The otherwise-unprintable Unicode BOM is represented as "BOM" in the example.

  <165>1 2003-10-11T22:14:15.003Z mymachine.example.com
  evntslog - ID47 [exampleSDID@0 iut="3" eventSource="Application"
  eventID="1011"] BOMAn application event log entry...

This syslog message leads to the following entries in the syslogMsgTable and the syslogMsgSDTable (note that string indexes are written as strings for readability reasons):

  syslogMsgIndex.1 = 1
  syslogMsgFacility.1 = 20
  syslogMsgSeverity.1 = 5
  syslogMsgVersion.1 = 1
  syslogMsgTimeStamp.1 = 2003-10-11,22:14:15.003,+0:0
  syslogMsgHostName.1 = "mymachine.example.com"
  syslogMsgAppName.1 = "evntslog"
  syslogMsgProcID.1 = "-"
  syslogMsgMsgID.1 = "ID47"
  syslogMsgMsg.1 = "BOMAn application event log entry..."
  syslogMsgSDParamValue.1.1."exampleSDID@0"."iut"
      = "3"
  syslogMsgSDParamValue.1.2."exampleSDID@0"."eventSource"
      = "Application"
  syslogMsgSDParamValue.1.3."exampleSDID@0"."eventID"
      = "1011"


 TOC 

9.  IANA Considerations

The IANA is requested to assign a value for "XXX" under the 'mib-2' subtree and to record the assignment in the SMI Numbers registry. When the assignment has been made, the RFC Editor is asked to replace "XXX" (here and in the MIB module) with the assigned value.



 TOC 

10.  Security Considerations

There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability:

Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability:

SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPsec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module.

It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC3410], section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy).

Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them.



 TOC 

11.  Acknowledgments

The editors wish to thank the following individuals for providing helpful comments on various versions of this document: Martin Bjorklund, Washam Fan, Rainer Gerhards, Wes Hardacker, David Harrington, Tom Petch, Juergen Quittek, Dan Romascanu, and Bert Wijnen.



 TOC 

12.  References



 TOC 

12.1. Normative References

[I-D.ietf-opsawg-syslog-snmp] Marinov, V. and J. Schoenwaelder, “Mapping Simple Network Management Protocol (SNMP) Notifications to SYSLOG Messages,” Internet Draft (work in progress), March 2009.
[RFC2119] Bradner, S., “Key words for use in RFCs to Indicate Requirement Levels,” BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder, “Structure of Management Information Version 2 (SMIv2),” RFC 2578, STD 58, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder, “Textual Conventions for SMIv2,” RFC 2579, STD 58, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder, “Conformance Statements for SMIv2,” RFC 2580, STD 58, April 1999.
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, “An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks,” STD 62, RFC 3411, December 2002.
[RFC3412] Case, J., Harrington, D., Presuhn, R., and B. Wijnen, “Message Processing and Dispatching for the Simple Network Management Protocol (SNMP),” STD 62, RFC 3412, December 2002.
[RFC5424] Gerhards, R., “The Syslog Protocol,” RFC 5424, March 2009.
[RFC5427] Keeni, G., “Textual Conventions for Syslog Management,” RFC 5427, March 2009.


 TOC 

12.2. Informative References

[RFC3014] Kavasseri, R., Ed., “Notification Log MIB,” RFC 3014, November 2002.
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, “Introduction and Applicability Statements for Internet-Standard Management Framework,” RFC 3410, December 2002.


 TOC 

Authors' Addresses

  Juergen Schoenwaelder
  Jacobs University Bremen
  Campus Ring 1
  28725 Bremen
  Germany
Email:  j.schoenwaelder@jacobs-university.de
  
  Alexander Clemm
  Cisco Systems
  170 West Tasman Drive
  San Jose, CA 95134-1706
  USA
Email:  alex@cisco.com
  
  Anirban Karmakar
  Cisco Systems
  170 West Tasman Drive
  San Jose, CA 95134-1706
  USA
Email:  akarmaka@cisco.com