Network Working Group P. Psenak Internet-Draft Cisco Systems Intended status: Standards Track S. Mirtorabi Expires: July 24, 2007 Force10 Networks A. Roy L. Nguyen P. Pillay-Esnault Cisco Systems January 20, 2007 Multi-Topology (MT) Routing in OSPF draft-ietf-ospf-mt-08.txt Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on July 24, 2007. Copyright Notice Copyright (C) The IETF Trust (2007). Psenak, et al. Expires July 24, 2007 [Page 1] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 Abstract This draft describes an extension to Open Shortest Path First (OSPF) in order to define independent IP topologies called Multi-Topologies (MTs). The Multi-Topologies extension can be used for computing different paths for unicast traffic, multicast traffic, different classes of service based on flexible criteria, or an in-band network management topology. An optional extension to exclude selected links from the default topology is also described. Psenak, et al. Expires July 24, 2007 [Page 2] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1. Differences between Multi-Topology and TOS Based Routing . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1. Requirements notation . . . . . . . . . . . . . . . . . . 5 2.2. Terms . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. Base MT Functional Specifications . . . . . . . . . . . . . . 6 3.1. MT Area Boundary . . . . . . . . . . . . . . . . . . . . . 6 3.2. Adjacency for MTs . . . . . . . . . . . . . . . . . . . . 6 3.3. Sending OSPF control packets . . . . . . . . . . . . . . . 6 3.4. Advertising MT Adjacencies and the Corresponding IP Prefixes . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.4.1. Inter-Area and External Routing . . . . . . . . . . . 7 3.5. Flushing MT Information . . . . . . . . . . . . . . . . . 7 3.6. MT SPF Computation . . . . . . . . . . . . . . . . . . . . 7 3.7. MT-ID Values . . . . . . . . . . . . . . . . . . . . . . . 7 3.8. Forwarding in MT . . . . . . . . . . . . . . . . . . . . . 8 4. Default Topology Link Exclusion Functional Specifications . . 9 4.1. Exclusion of Links in the Default Topology . . . . . . . . 9 4.2. New Area Data Structure Parameter . . . . . . . . . . . . 9 4.3. Adjacency Formation with Link Exclusion Capability . . . . 10 4.4. OSPF Control Packets Transmission Over Excluded Links . . 11 4.5. OSPF LSA Advertisement and SPF Computation for Excluded Links . . . . . . . . . . . . . . . . . . . . . . 11 5. Interoperability between MT Capable and Non-MT Capable Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5.1. Demand Circuit Compatibility Considerations . . . . . . . 12 6. Migration from non-MT-Area to MT-area . . . . . . . . . . . . 13 7. MT Network Management Considerations . . . . . . . . . . . . . 14 7.1. Create dedicated management topology to include all the nodes . . . . . . . . . . . . . . . . . . . . . . . . 14 7.2. Extend the default topology to all the nodes . . . . . . . 14 8. Security Considerations . . . . . . . . . . . . . . . . . . . 15 9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 16 10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 17 10.1. Normative References . . . . . . . . . . . . . . . . . . . 17 10.2. Informative References . . . . . . . . . . . . . . . . . . 17 Appendix A. Acknowledgments . . . . . . . . . . . . . . . . . . . 18 Appendix B. OSPF data formats . . . . . . . . . . . . . . . . . . 19 B.1. Router-LSAs . . . . . . . . . . . . . . . . . . . . . . . 19 B.2. Network-LSAs . . . . . . . . . . . . . . . . . . . . . . . 20 B.3. Summary-LSAs . . . . . . . . . . . . . . . . . . . . . . . 20 B.4. AS-external-LSAs . . . . . . . . . . . . . . . . . . . . . 21 B.5. Type-7 AS-external-LSAs . . . . . . . . . . . . . . . . . 23 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 24 Intellectual Property and Copyright Statements . . . . . . . . . . 25 Psenak, et al. Expires July 24, 2007 [Page 3] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 1. Introduction OSPF uses a fixed packet format, therefore it is not easy to introduce any backward compatible extensions. However, the OSPF specification [OSPF] introduced Type of Service (TOS) metric in an earlier specification [TOS-OSPF] in order to announce a different link cost based on TOS. TOS based routing as described in [TOS-OSPF] was never deployed and was subsequently deprecated. [M-ISIS] describes a similar mechanism for ISIS. We propose to reuse the TOS based metric fields. They have been redefined and are used to advertise different topologies by advertising separate metrics for each of them. 1.1. Differences between Multi-Topology and TOS Based Routing Multi-Topology routing differs from [TOS-OSPF] TOS based routing in the following ways: 1. With TOS routing [TOS-OSPF], the TOS or DSCP in the IP header is mapped directly to the corresponding OSPF SPF calculation and routing table. This limits the number and definition of the topologies to the 16 TOS values specified in section 12.3 of [TOS-OSPF]. With Multi-Topology routing, the classification of what type of traffic maps to which topology is not within the scope of the document. 2. With TOS routing [TOS-OSPF], traffic which is unreachable in the routing table associated with the corresponding TOS will revert to the TOS 0 routing table. With Multi-Topology routing, this is optional. 3. With TOS routing [TOS-OSPF], individual links or prefixes could not be excluded from a topology. If the LSA options T-bit was set, all links or prefixes were either advertised explicitly or defaulted to the TOS 0 metric. With Multi-Topology routing, links or prefixes that are not advertised for a specific topology do not exist in that topology. Psenak, et al. Expires July 24, 2007 [Page 4] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 2. Terminology 2.1. Requirements notation The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC-KEYWORDS]. 2.2. Terms We define the following terminology in this document: Non-MT router Routers that do not have the MT capability MT router Routers that have MT capability as described in this document MT-ID Renamed TOS field in LSAs to represent Multi-Topology ID. Default topology Topology that is built using the TOS 0 metric (default metric) MT topology Topology that is built using the corresponding MT-ID metric MT Shorthand notation for MT topology MT#0 topology Representation of TOS 0 metric in MT-ID format Non-MT-Area An area that contains only non-MT routers MT-Area An area that contains both non-MT routers and MT routers or only MT routers Psenak, et al. Expires July 24, 2007 [Page 5] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 3. Base MT Functional Specifications 3.1. MT Area Boundary Each OSPF interface belongs to a single area and all MTs sharing that link need to belong to the same area. Therefore the area boundaries for all MTs are the same but each MT's attachment to the area is independent. 3.2. Adjacency for MTs Each interface can be configured to belong to a set of topologies. A single adjacency is formed with neighbors on the interface even if the interface is configured to participate in multiple topologies. Furthermore, adjacency formation is independent of the topologies configured on the local interface and the neighboring router. 3.3. Sending OSPF control packets Sending OSPF control packets is unchanged from [OSPF]. For OSPF control packets sent to the remote end of a virtual link, the transit area path MUST be composed of links participating in the default topology and the OSPF control packets MUST be forwarded using the default topology. 3.4. Advertising MT Adjacencies and the Corresponding IP Prefixes The TOS metric field is reused to advertise topology specific metric for links and prefixes belonging to that topology. The TOS field is redefined as MT-ID in the payload of Router, Summary, Type-5 and Type-7 AS-external LSAs (see Appendix A). MT-ID metrics in LSAs SHOULD be in ascending order of MT-ID. If an MT-ID exists in an LSA or router link multiple times, the metric in the first MT-ID instance MUST be used. When a router establishes a FULL adjacency over a link that belongs to a set of MTs, it advertises the corresponding cost for each MT-ID. By default, all links are included in the default topology and all advertised prefixes belonging to the default topology will use the TOS0 metric as in [OSPF]. Each MT has its own MT-ID metric field. When a link is not part of a given MT, the corresponding MT-ID metric is excluded from the LSA. The Network-LSA does not contain any MT information since the Designated Router (DR) is shared by all MTs. Hence, there is no Psenak, et al. Expires July 24, 2007 [Page 6] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 change to the Network-LSA. 3.4.1. Inter-Area and External Routing In Summary-LSAs, Type-5 and Type-7 AS-external-LSAs the TOS metric fields are redefined as MT-ID metric fields and are used to advertise prefix and router reachability in the corresponding topology. When a router originates a Summary-LSA, Type-5 or Type-7 AS-external- LSA that belongs to a set of MTs, it includes the corresponding cost for each MT-ID. By default, the prefix participates in the default topology and uses the TOS0 metric for the default topology, similar to standard OSPF [OSPF]. Setting the P-bit in Type-7 AS-external-LSA is topology independent and pertains to all MT-ID advertised in the body of the LSA. 3.5. Flushing MT Information When a certain link or prefix that existed or was reachable in a certain topology is no longer part of that topology or is unreachable in that topology, a new version of the LSA MUST be originated excluding metric information representing the link or prefix in that topology. The MT metric in the Router-LSA can also be set to the maximum possible metric to enable the router to become a stub in a certain topology [STUB]. 3.6. MT SPF Computation By considering MT-ID metrics in the LSAs, OSPF computes multiple topologies and finds paths to IP prefixes for each MT independently. A separate SPF will be computed for each MT-ID to find independent paths to IP prefixes. Network-LSAs are used by all topologies during the SPF computation. During the SPF for a given MT-ID, only the links and metrics for that MT-ID are considered. Entries in the Router Routing table are also MT-ID specific. 3.7. MT-ID Values Since AS-External-LSAs use the high order bit in the MT-ID field (E bit) for the external metric-type, only MT-IDs in the 0 to 127 range are valid. The following MT-ID values are reserved: Psenak, et al. Expires July 24, 2007 [Page 7] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 0 - Reserved for advertising the metric associated with the default topology (see Section 4.2) 1 - Reserved for advertising the metric associated with the default multicast topology 2 - Reserved for IPv4 in-band management purposes. 3-31 - Reserved for IETF consensus. 32-127 - Reserved for development, experimental and proprietary features [RFC3692]. 128-255 - Invalid and SHOULD be ignored. 3.8. Forwarding in MT It is outside of the scope of this document to specify how the information in various topology specific forwarding structures are used during packet forwarding or how incoming packets are associated with the corresponding topology. For correct operation, both forwarding behavior and methods of associating incoming packets to a corresponding topology must be consistently applied in the network. Psenak, et al. Expires July 24, 2007 [Page 8] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 4. Default Topology Link Exclusion Functional Specifications The Multi-Topologies imply that all the routers participate in the default topology. However, it can be useful to exclude some links from the default topology and reserve them for some specific classes of traffic. The Multi-Topologies extension for the default topology link or prefix exclusion is described in the following subsections. 4.1. Exclusion of Links in the Default Topology OSPF does not have the notion of an unreachable link. All links can have a maximum metric of 0xFFFF advertised in the Router-LSA. The link exclusion capability requires routers to ignore TOS0 metrics in Router-LSAs in the default topology and to alternately use the MT- ID#0 metric to advertise the metric associated with the default topology. Hence, all routers within an area MUST agree on how the metric for the default topology will be advertised. The unused T-bit is defined as the MT-bit in the option field in order to assure that a Multi-Topology link-excluding capable router will only form an adjacency with another similarly configured router. +---+---+---+---+---+---+---+---+ |DN |O |DC |EA |NP |MC |E |MT | +---+---+---+---+---+---+---+---+ Figure 1: OSPF Option Bits MT-bit: If DefaultExclusionCapability is enabled, the bit MUST be set in Hello packets and SHOULD be set in Database Description packet (see Section 4.2). 4.2. New Area Data Structure Parameter We define a new parameter in the Area Data Structure: DefaultExclusionCapability This configurable parameter ensures that all routers in an area have this capability enabled before the default topology can be disabled on a router link in the area without causing backward compatibility problems. When an area data structure is created, the DefaultExclusionCapability is disabled by default. Psenak, et al. Expires July 24, 2007 [Page 9] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 If DefaultExclusionCapability is disabled: o The MT-bit MUST be cleared in Hello packet and SHOULD be cleared in Database Description packets. o If a link participates in a non-default topology, it is automatically included in the default topology to support backward compatibility between MT and non-MT routers. This is accomplished using the TOS0 metric field as in [OSPF]. If DefaultExclusionCapability is enabled: o The MT-bit MUST be set in Hello packets and SHOULD be set in Database Description packets. o The router will only accept a Hello packet if the MT-bit is set (see Section 4.3). When DefaultExclusionCapability is set to enabled a router is said to be operating in DefaultExclusionCapability mode. 4.3. Adjacency Formation with Link Exclusion Capability In order to have a smooth transition from a non-MT area to an MT- area, an MT router with DefaultExclusionCapability disabled will form adjacencies with non-MT routers and will include all links as part of the default topology. A link may cease participating in the default topology if DefaultExclusionCapability is set to enabled. In this state, a router will only form adjacency with routers that set the MT-bit in their Hello packets. This will ensure that all routers have DefaultExclusionCapability enabled before the default topology can be disabled on a link. Receiving OSPF Hello packets as defined in section 10.5 of [OSPF] is modified as follows: o If the DefaultExclusionCapability in the Area Data structure is set to enabled, Hello packets are discarded if the received packet does not have the MT-bit set in the Header Options. Receiving OSPF Database Description packets as defined in section 10.6 of [OSPF] is unchanged. While packet options are validated in Hello packets, the only option checking performed for Database Description packets is assuring that the options do not change during the database exchange process. Psenak, et al. Expires July 24, 2007 [Page 10] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 4.4. OSPF Control Packets Transmission Over Excluded Links If DefaultExclusionCapability is enabled, the default topology can be disabled on an interface. Disabling the default topology on an interface does not impact the installation of connected routes for the interface in the default topology. It only affects what a router advertises in its Router-LSA. This allows OSPF control packets to be sent and received over an interface even if the default topology is disabled on the interface. 4.5. OSPF LSA Advertisement and SPF Computation for Excluded Links When DefaultExclusionCapability is enabled and the link does not participate in the default topology, MT-ID#0 metric is not advertised. The link's TOS0 metric is ignored during the default topology SPF computation. When DefaultExclusionCapability is enabled and a link participates in the default topology, MT-ID#0 metric is used to advertise the metric associated with the default topology. The link's TOS0 metric is ignored during the default topology SPF computation. Independent of the DefaultExclusionCapability, the TOS0 metric is used for Summary-LSAs, Type-5 and Type-7 AS-external-LSAs. o If the prefix or router does not exist in the default topology, the TOS0 metric is set to infinity (0xFFFFFF). o If the prefix or router exists in the default topology, the TOS0 metric is used to advertise the metric in the default topology. During the summary and external prefix calculation for the default topology the TOS0 metric is used for Summary-LSAs, Type-5 and Type-7 AS-external-LSAs. Psenak, et al. Expires July 24, 2007 [Page 11] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 5. Interoperability between MT Capable and Non-MT Capable Routers The default metric field is mandatory in all LSAs (even when metric value is 0). Even when a link or prefix does not exist in the default topology, a non-MT router will consider the zero value in the metric field as a valid metric and consider the link or prefix as part of the default topology. In order to prevent the above problem, an MT capable router will include all links as part of the default topology. If links need to be removed from the default topology, an MT capable router must be configured in DefaultExclusionCapability mode. In this mode, routers will assure that all other routers in the area are in the DefaultExclusionCapability mode before considering the MT-ID#0 metric in the SPF calculation. Only then the TOS0 metric field in Router LSAs can be safely ignored during the default topology SPF computation. Note that for any prefix or router to become reachable in a certain topology, a contiguous path inside that topology must exist between the calculating router and the destination prefix or router. 5.1. Demand Circuit Compatibility Considerations A change to an area's DefaultExclusionCapability requires additional processing for area neighbors that are suppressing Hello packets as specified in "Extending OSPF to Support Demand Circuits" [DEMAND]. When the DefaultExclusionCapability for an area is changed, Hello suppression must be disabled for these neighbors for a period of RouterDeadInterval seconds. This implies that Hello packets are sent with the DC bit clear as specified in section 3.2.1 of [DEMAND] during this period. After RouterDeadInterval seconds, either the adjacency will be taken down due to rejection of Hello packets with a conflicting MT-bit or Hello suppression will be renegotiated. Psenak, et al. Expires July 24, 2007 [Page 12] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 6. Migration from non-MT-Area to MT-area Introducing MT-OSPF into a network can be done gradually to allow MT routers and non-MT routers to participate in the default topology while MT routers participate in other topologies. If there is a requirement to exclude some links from the default topology in an area, all routers in the area MUST be in DefaultExclusionCapability mode. In this section we describe the migration steps to consider while transitioning from a non-MT network to an MT network. Consider a network with a backbone area and a set of non-backbone areas functioning in standard OSPF mode. We would like to migrate to an MT network either partially or completely. 1. As required, part of an area is upgrade to be MT capable. The MT routers will interact with non-MT routers in the default topology and participate in other topologies as required. 2. If a new non-backbone area is created for MT routers, it may be configured in DefaultExclusionCapability mode since there is no interaction required with non-MT routers. In this mode, the default topology can be excluded on links as required. 3. If there are several non-backbone areas where MT is being used, it is desirable that the backbone area first be upgraded to be MT capable so that inter-area routing is assured for MT destinations in different areas. 4. Gradually the whole network can be made MT capable. Note that inter-area routing for the MT-area still depends on the backbone area. Therefore, if different areas configured for a given topology need to communicate, the backbone area also needs to be configured for this topology. Psenak, et al. Expires July 24, 2007 [Page 13] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 7. MT Network Management Considerations When multiple OSPF topologies exist within a domain, some of the routers can be configured to participate in a subset of the MTs in the network. This section discusses some of the options we have to enable operations or the network management stations to access those routers. 7.1. Create dedicated management topology to include all the nodes This approach is to setup a dedicated management topology or 'in- band' management topology. This 'mgmt' topology will include all the routers need to be managed. The computed routes in the topology will be installed into the 'mgmt' RIB. In the condition of the 'mgmt' topology uses a set of non-overlapping address space with the default topology, those 'mgmt' routes can also be optionally installed into the default RIB. The advantages of duplicate 'mgmt' routes in both RIBs include: the network management utilities on the system does not have to be modified to use specific RIB other than the default RIB; the 'mgmt' topology can share the same link with the default topology if so designed. 7.2. Extend the default topology to all the nodes Even in the case default topology is not used on some of the nodes in the IP forwarding, we may want to extend the default topology to those nodes for the purpose of network management. Operators SHOULD set high cost on the links which belong to the extended portion of the default topology. This way the IP data traffic will not be forwarded through those nodes during network topology changes. Psenak, et al. Expires July 24, 2007 [Page 14] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 8. Security Considerations This document does not raise any security issues that are not already covered in [OSPF]. Psenak, et al. Expires July 24, 2007 [Page 15] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 9. IANA Considerations The T-bit as defined in [TOS-OSPF] for a router's TOS capability is redefined as the MT-bit in this document. No IANA action is required for the MT-bit. Similarly, the TOS field for Router-LSAs, Summary-LSAs, Type-5 and Type-7 AS-external LSAs as defined in [OSPF] is redefined as MT-ID in Section 3.7. IANA is requested to create a new registry, "OSPF multi-topology ID values" with the assignment listed in Section 3.7 of this document and registration policies for future assignments. Psenak, et al. Expires July 24, 2007 [Page 16] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 10. References 10.1. Normative References [DEMAND] Moy, J., "Extending OSPF to Support Demand Circuits", RFC 1793, April 1995. [NSSA] Murphy, P., "The OSPF Not-So-Stubby Area (NSSA) Option", RFC 3101, January 2003. [OSPF] Moy, J., "OSPF Version 2", RFC 2328, April 1998. [RFC-KEYWORDS] Bradner, S., "Key words for use in RFC's to Indicate Requirement Levels", RFC 2119, March 1997. [RFC3692] Narten, T., "Assigning Experimental and Testing Numbers Considered Useful", RFC 3692, January 2004. [TOS-OSPF] Moy, J., "OSPF Version 2", RFC 1583, March 1994. 10.2. Informative References [M-ISIS] Przygienda, T., Shen, N., and N. Sheth, "M-ISIS: Multi Topology (MT) Routing in IS-IS", draft-ietf-isis-wg-multi-topology-11.txt (work in progress). [STUB] Retana, A., Nguyen, L., White, R., Zinin, A., and D. McPherson, "OSPF Stub Router Advertisement", RFC 3137, June 2001. Psenak, et al. Expires July 24, 2007 [Page 17] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 Appendix A. Acknowledgments The authors would like to thank Scott Sturgess, Alvaro Retana, David Kushi, Yakov Rekhter, Tony Przygienda, and Naiming Shen for their comments on the document. Special thanks to Acee Lindem for editing and to Tom Henderson for an extensive review during the OSPF Working Group last call. Psenak, et al. Expires July 24, 2007 [Page 18] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 Appendix B. OSPF data formats LSA content defined in [OSPF] is modified to introduce the MT-ID. B.1. Router-LSAs Router-LSAs are the Type 1 LSAs. Each router in an area originates a router-LSA. The LSA describes the state and cost of the router's links (i.e., interfaces) to the area. All of the router's links to the area must be described in a single router-LSA. For details concerning the construction of router-LSAs, see Section 12.4.1 of [OSPF]. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS age | Options | 1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link State ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Advertising Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS sequence number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS checksum | length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |*|*|*|N|W|V|E|B| 0 | # links | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link Data | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | # MT-ID | metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MT-ID | 0 | MT-ID metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MT-ID | 0 | MT-ID metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link Data | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ... | Figure 2: Router-LSA Format Psenak, et al. Expires July 24, 2007 [Page 19] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 B.2. Network-LSAs Network-LSAs are the Type 2 LSAs. A network-LSA is originated for each broadcast and NBMA network in the area which supports two or more routers. The network-LSA is originated by the network's Designated Router. The LSA describes all routers attached to the network, including the Designated Router itself. The LSA's Link State ID field lists the IP interface address of the Designated Router. The distance from the network to all attached routers is zero. This is why metric fields need not be specified in the network-LSA. For details concerning the construction of network-LSAs, see Section 12.4.2 of [OSPF]. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS age | Options | 2 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link State ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Advertising Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS sequence number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS checksum | length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Network Mask | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Attached Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ... | Figure 3: Network-LSA Format Note that network LSA does not contain any MT-ID fields as the cost of the network to the attached routers is 0 and DR is shared by all topologies. B.3. Summary-LSAs Summary-LSAs are the Type 3 and 4 LSAs. These LSAs are originated by area border routers. Summary-LSAs describe inter-area destinations. For details concerning the construction of summary-LSAs, see Section 12.4.3 [OSPF]. Psenak, et al. Expires July 24, 2007 [Page 20] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 Type 3 summary-LSAs are used when the destination is an IP network. In this case the LSA's Link State ID field is an IP network number (if necessary, the Link State ID can also have one or more of the network's "host" bits set; see Appendix E [OSPF] for details). When the destination is an AS boundary router, a Type 4 summary-LSA is used, and the Link State ID field is the AS boundary router's OSPF Router ID. (To see why it is necessary to advertise the location of each ASBR, consult Section 16.4 of [OSPF]). Other than the difference in the Link State ID field, the format of Type 3 and 4 summary-LSAs is identical. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS age | Options | 3 or 4 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link State ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Advertising Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS sequence number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS checksum | length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Network Mask | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0 | metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MT-ID | MT-ID metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MT-ID | MT-ID metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 4: Summary-LSA Format B.4. AS-external-LSAs AS-external-LSAs are the Type 5 LSAs. These LSAs are originated by AS boundary routers, and describe destinations external to the AS. For details concerning the construction of AS-external-LSAs, see Section 12.4.3 of [OSPF]. AS-external-LSAs usually describe a particular external destination. For these LSAs the Link State ID field specifies an IP network number (if necessary, the Link State ID can also have one or more of the Psenak, et al. Expires July 24, 2007 [Page 21] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 network's "host" bits set; see Appendix E [OSPF] for details). AS- external-LSAs are also used to describe a default route. Default routes are used when no specific route exists to the destination. When describing a default route, the Link State ID is always set to DefaultDestination (0.0.0.0) and the Network Mask is set to 0.0.0.0. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS age | Options | 5 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link State ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Advertising Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS sequence number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS checksum | length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Network Mask | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |E| 0 | metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Forwarding address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | External Route Tag | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |E| MT-ID | MT-ID metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Forwarding address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | External Route Tag | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |E| MT-ID | MT-ID metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Forwarding address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | External Route Tag | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 5: AS-External-LSA Format Psenak, et al. Expires July 24, 2007 [Page 22] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 B.5. Type-7 AS-external-LSAs Type-7 AS-external-LSAs are originated by AS boundary routers local to an NSSA, and describe destinations external to the AS. The changes to Type-7 AS-external-LSAs are identical to those for AS- external-LSAs (Appendix A.4.5). For details concerning the construction of Type-7 AS-external-LSAs see Section 2.4 of [NSSA]. Psenak, et al. Expires July 24, 2007 [Page 23] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 Authors' Addresses Peter Psenak Cisco Systems Mlynske Nivy 43 821 09 Bratislava Slovakia Email: ppsenak@cisco.com Sina Mirtorabi Force10 Networks 1440 McCarthy Blvd Milpitas, CA 95035 USA Email: sina@force10networks.com Abhay Roy Cisco Systems 170 West Tasman Drive San Jose, CA 95134 USA Email: akr@cisco.com Liem Nguyen Cisco Systems 170 West Tasman Drive San Jose, CA 95134 USA Email: lhnguyen@cisco.com Padma Pillay-Esnault Cisco Systems 170 West Tasman Drive San Jose, CA 95134 USA Email: ppe@cisco.com Psenak, et al. Expires July 24, 2007 [Page 24] Internet-Draft Multi-Topology (MT) Routing in OSPF January 2007 Full Copyright Statement Copyright (C) The IETF Trust (2007). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Acknowledgment Funding for the RFC Editor function is provided by the IETF Administrative Support Activity (IASA). Psenak, et al. Expires July 24, 2007 [Page 25]