Routing Area Working Group P. Sarkar, Ed.
Internet-Draft Individual Contributor
Intended status: Standards Track S. Hegde
Expires: July 24, 2017 C. Bowers
Juniper Networks, Inc.
H. Gredler
RtBrick, Inc.
S. Litkowski
Orange
January 20, 2017
Remote-LFA Node Protection and Manageability
draft-ietf-rtgwg-rlfa-node-protection-11
Abstract
The loop-free alternates computed following the current Remote-LFA
specification guarantees only link-protection. The resulting Remote-
LFA nexthops (also called PQ-nodes), may not guarantee node-
protection for all destinations being protected by it.
This document describes an extension to the Remote Loop-Free based IP
fast reroute mechanisms described in [RFC7490], that describes
procedures for determining if a given PQ-node provides node-
protection for a specific destination or not. The document also
shows how the same procedure can be utilized for collection of
complete characteristics for alternate paths. Knowledge about the
characteristics of all alternate path is precursory to apply operator
defined policy for eliminating paths not fitting constraints.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC2119 [RFC2119].
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Sarkar, et al. Expires July 24, 2017 [Page 1]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on July 24, 2017.
Copyright Notice
Copyright (c) 2017 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Abbreviations . . . . . . . . . . . . . . . . . . . . . . 3
2. Node Protection with Remote-LFA . . . . . . . . . . . . . . . 4
2.1. The Problem . . . . . . . . . . . . . . . . . . . . . . . 4
2.2. Additional Definitions . . . . . . . . . . . . . . . . . 6
2.2.1. Link-Protecting Extended P-Space . . . . . . . . . . 6
2.2.2. Node-Protecting Extended P-Space . . . . . . . . . . 6
2.2.3. Q-Space . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.4. Link-Protecting PQ Space . . . . . . . . . . . . . . 7
2.2.5. Candidate Node-Protecting PQ Space . . . . . . . . . 7
2.2.6. Cost-Based Definitions . . . . . . . . . . . . . . . 7
2.2.6.1. Link-Protecting Extended P-Space . . . . . . . . 7
2.2.6.2. Node-Protecting Extended P-Space . . . . . . . . 8
2.2.6.3. Q-Space . . . . . . . . . . . . . . . . . . . . . 9
2.3. Computing Node-protecting R-LFA Path . . . . . . . . . . 9
2.3.1. Computing Candidate Node-protecting PQ-Nodes for
Primary nexthops . . . . . . . . . . . . . . . . . . 9
2.3.2. Computing node-protecting paths from PQ-nodes to
destinations . . . . . . . . . . . . . . . . . . . . 11
2.3.3. Computing Node-Protecting R-LFA Paths for
Destinations with ECMP primary nexthop nodes . . . . 13
2.3.4. Limiting extra computational overhead . . . . . . . . 17
3. Manageability of Remote-LFA Alternate Paths . . . . . . . . . 18
3.1. The Problem . . . . . . . . . . . . . . . . . . . . . . . 18
Sarkar, et al. Expires July 24, 2017 [Page 2]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
3.2. The Solution . . . . . . . . . . . . . . . . . . . . . . 19
4. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 19
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 19
6. Security Considerations . . . . . . . . . . . . . . . . . . . 19
7. References . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.1. Normative References . . . . . . . . . . . . . . . . . . 19
7.2. Informative References . . . . . . . . . . . . . . . . . 20
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 20
1. Introduction
The Remote-LFA [RFC7490] specification provides loop-free alternates
that guarantee only link-protection. The resulting Remote-LFA
alternate nexthops (also referred to as the PQ-nodes) may not provide
node-protection for all destinations covered by the same, in case of
failure of the primary nexthop node. Neither does the specification
provide a means to determine the same.
Also, the LFA Manageability [RFC7916] document requires a computing
router to find all possible (including all possible Remote-LFA)
alternate nexthops, collect the complete set of path characteristics
for each alternate path, run an alternate-selection policy
(configured by the operator) and find the best alternate path. This
will require the Remote-LFA implementation to gather all the required
path characteristics along each link on the entire Remote-LFA
alternate path.
With current LFA [RFC5286] and Remote-LFA implementations, the
forward SPF (and reverse SPF) is run with the computing router and
its immediate 1-hop routers as the roots. While that enables
computation of path attributes (e.g. SRLG, Admin-groups) for first
alternate path segment from the computing router to the PQ-node,
there is no means for the computing router to gather any path
attributes for the path segment from the PQ-node to destination.
Consequently any policy-based selection of alternate paths will
consider only the path attributes from the computing router up until
the PQ-node.
This document describes a procedure for determining node-protection
with Remote-LFA. The same procedure is also extended for collection
of a complete set of path attributes, enabling more accurate policy-
based selection for alternate paths obtained with Remote-LFA.
1.1. Abbreviations
This document uses the following list of abbreviations.
LFA - Loop Free Alternates
Sarkar, et al. Expires July 24, 2017 [Page 3]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
RLFA or R-LFA - Remote Loop Free Alternates
ECMP - Equal Cost Multiple Path
SPF - Shortest Path First graph computations
NH - Next Hop node
2. Node Protection with Remote-LFA
Node-protection is required to provide protection of traffic on a
given forwarding node, against the failure of the first-hop node on
the primary forwarding path. Such protection becomes more critical
in the absence of mechanisms like non-stop-routing in the network.
Certain operators refrain from deploying non-stop-routing in their
network, due to the required complex state synchronization between
redundant control plane hardwares it requires, and the significant
additional performance complexities it hence introduces. In such
cases node-protection is essential to guarantee un-interrupted flow
of traffic, even in the case of an entire forwarding node going down.
The following sections discuss the node-protection problem in the
context of Remote-LFA and propose a solution.
2.1. The Problem
To better illustrate the problem and the solution proposed in this
document the following topology diagram from the Remote-LFA [RFC7490]
draft is being re-used with slight modification.
D1
/
S-x-E
/ \
N R3--D2
\ /
R1---R2
Figure 1: Topology 1
In the above topology, for all (non-ECMP) destinations reachable via
the S-E link there is no standard LFA alternate. As per the Remote-
LFA [RFC7490] alternate specifications node R2 being the only PQ-node
for the S-E link provides nexthop for all the above destinations.
Table 1 below, shows all possible primary and Remote-LFA alternate
paths for each destination.
Sarkar, et al. Expires July 24, 2017 [Page 4]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
+-------------+--------------+---------+-------------------------+
| Destination | Primary Path | PQ-node | Remote-LFA Backup Path |
+-------------+--------------+---------+-------------------------+
| R3 | S->E->R3 | R2 | S=>N=>R1=>R2->R3 |
| E | S->E | R2 | S=>N=>R1=>R2->R3->E |
| D1 | S->E->D1 | R2 | S=>N=>R1=>R2->R3->E->D1 |
| D2 | S->E->R3->D2 | R2 | S=>N=>R1=>R2->R3->D2 |
+-------------+--------------+---------+-------------------------+
Table 1: Remote-LFA backup paths via PQ-node R2
A closer look at Table 1 shows that, while the PQ-node R2 provides
link-protection for all the destinations, it does not provide node-
protection for destinations E and D1. In the event of the node-
failure on primary nexthop E, the alternate path from Remote-LFA
nexthop R2 to E and D1 also becomes unavailable. So for a Remote-LFA
nexthop to provide node-protection for a given destination, it is
mandatory that, the shortest path from the given PQ-node to the given
destination MUST NOT traverse the primary nexthop.
In another extension of the topology in Figure 1 let us consider an
additional link between N and E with the same cost as the other
links.
D1
/
S-x-E
/ / \
N---+ R3--D2
\ /
R1---R2
Figure 2: Topology 2
In the above topology, the S-E link is no more on any of the shortest
paths from N to R3, E and D1. Hence R3, E and D1 are also included
in both the Extended-P space and Q space of E (w.r.t S-E link).
Table 2 below, shows all possible primary and R-LFA alternate paths
via PQ-node R3, for each destination reachable through the S-E link
in the above topology. The R-LFA alternate paths via PQ-node R2
remains same as in Table 1.
Sarkar, et al. Expires July 24, 2017 [Page 5]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
+-------------+--------------+---------+------------------------+
| Destination | Primary Path | PQ-node | Remote-LFA Backup Path |
+-------------+--------------+---------+------------------------+
| R3 | S->E->R3 | R3 | S=>N=>E=>R3 |
| E | S->E | R3 | S=>N=>E=>R3->E |
| D1 | S->E->D1 | R3 | S=>N=>E=>R3->E->D1 |
| D2 | S->E->R3->D2 | R3 | S=>N=>E=>R3->D2 |
+-------------+--------------+---------+------------------------+
Table 2: Remote-LFA backup paths via PQ-node R3
Again a closer look at Table 2 shows that, unlike Table 1, where the
single PQ-node R2 provided node-protection for destinations R3 and
D2, if we choose R3 as the R-LFA nexthop, it does not provide node-
protection for R3 and D2 anymore. If S chooses R3 as the R-LFA
nexthop, in the event of the node-failure on primary nexthop E, on
the alternate path from S to R-LFA nexthop R3, one of parallel ECMP
path between N and R3 also becomes unavailable. So for a Remote-LFA
nexthop to provide node-protection for a given destination, it is
also mandatory that, the shortest paths from S to the chosen PQ-node
MUST NOT traverse the primary nexthop node.
2.2. Additional Definitions
This document adds and enhances the following definitions extending
the ones mentioned in Remote-LFA [RFC7490] specification.
2.2.1. Link-Protecting Extended P-Space
The Remote-LFA [RFC7490] specification already defines this. The
link-protecting extended P-space for a link S-E being protected is
the set of routers that are reachable from one or more direct
neighbors of S, except primary node E, without traversing the S-E
link on any of the shortest paths from the direct neighbor to the
router. This MUST exclude any direct neighbor for which there is at
least one ECMP path from the direct neighbor traversing the link(S-E)
being protected.
For a cost-based definition for Link-protecting Extended P-Space
refer to Section 2.2.6.1.
2.2.2. Node-Protecting Extended P-Space
The node-protecting extended P-space for a primary nexthop node E
being protected, is the set of routers that are reachable from one or
more direct neighbors of S, except primary node E, without traversing
the node E. This MUST exclude any direct neighbors for which there
Sarkar, et al. Expires July 24, 2017 [Page 6]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
is at least one ECMP path from the direct neighbor traversing the
node E being protected.
For a cost-based definition for Node-protecting Extended P-Space
refer to Section 2.2.6.2.
2.2.3. Q-Space
The Remote-LFA [RFC7490] draft already defines this. The Q-space for
a link S-E being protected is the set of nodes that can reach primary
node E, without traversing the S-E link on any of the shortest paths
from the node itself to primary nexthop E. This MUST exclude any
node for which there is at least one ECMP path from the node to the
primary nexthop E traversing the link(S-E) being protected.
For a cost-based definition for Q-Space refer to Section 2.2.6.3.
2.2.4. Link-Protecting PQ Space
A node Y is in link-protecting PQ space w.r.t the link (S-E) being
protected, if and only if, Y is present in both link-protecting
extended P-space and the Q-space for the link being protected.
2.2.5. Candidate Node-Protecting PQ Space
A node Y is in candidate node-protecting PQ space w.r.t the node (E)
being protected, if and only if, Y is present in both node-protecting
extended P-space and the Q-space for the link being protected.
Please note, that a node Y being in candidate node-protecting PQ-
space, does not guarantee that the R-LFA alternate path via the same,
in entirety, is unaffected in the event of a node failure of primary
nexthop node E. It only guarantees that the path segment from S to
PQ-node Y is unaffected by the same failure event. The PQ-nodes in
the candidate node-protecting PQ space may provide node protection
for only a subset of destinations that are reachable through the
corresponding primary link.
2.2.6. Cost-Based Definitions
This section provides cost-based definitions for some of the terms
introduced in Section 2.2 of this document.
2.2.6.1. Link-Protecting Extended P-Space
Please refer to Section 2.2.1 for a formal definition for Link-
protecting Extended P-Space.
Sarkar, et al. Expires July 24, 2017 [Page 7]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
A node Y is in link-protecting extended P-space w.r.t the link (S-E)
being protected, if and only if, there exists at least one direct
neighbor of S, Ni, other than primary nexthop E, that satisfies the
following condition.
D_opt(Ni,Y) < D_opt(Ni,S) + D_opt(S,Y)
Where,
D_opt(A,B) : Distance on most optimum path from A to B.
Ni : A direct neighbor of S other than primary
nexthop E.
Y : The node being evaluated for link-protecting
extended P-Space.
Figure 3: Link-Protecting Ext-P-Space Condition
2.2.6.2. Node-Protecting Extended P-Space
Please refer to Section 2.2.2 for a formal definition for Node-
protecting Extended P-Space.
A node Y is in node-protecting extended P-space w.r.t the node E
being protected, if and only if, there exists at least one direct
neighbor of S, Ni, other than primary nexthop E, that satisfies the
following condition.
D_opt(Ni,Y) < D_opt(Ni,E) + D_opt(E,Y)
Where,
D_opt(A,B) : Distance on most optimum path from A to B.
E : The primary nexthop on shortest path from S
to destination.
Ni : A direct neighbor of S other than primary
nexthop E.
Y : The node being evaluated for node-protecting
extended P-Space.
Figure 4: Node-Protecting Ext-P-Space Condition
Please note, that a node Y satisfying the condition in Figure 4 above
only guarantees that the R-LFA alternate path segment from S via
direct neighbor Ni to the node Y is not affected in the event of a
node failure of E. It does not yet guarantee that the path segment
from node Y to the destination is also unaffected by the same failure
event.
Sarkar, et al. Expires July 24, 2017 [Page 8]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
2.2.6.3. Q-Space
Please refer to Section 2.2.3 for a formal definition for Q-Space.
A node Y is in Q-space w.r.t the link (S-E) being protected, if and
only if, the following condition is satisfied.
D_opt(Y,E) < D_opt(S,E) + D_opt(Y,S)
Where,
D_opt(A,B) : Distance on most optimum path from A to B.
E : The primary nexthop on shortest path from S
to destination.
Y : The node being evaluated for Q-Space.
Figure 5: Q-Space Condition
2.3. Computing Node-protecting R-LFA Path
The R-LFA alternate path through a given PQ-node to a given
destination is comprised of two path segments as follows.
1. Path segment from the computing router to the PQ-node (Remote-LFA
alternate nexthop), and
2. Path segment from the PQ-node to the destination being protected.
So to ensure a R-LFA alternate path for a given destination provides
node-protection we need to ensure that none of the above path
segments are affected in the event of failure of the primary nexthop
node. Sections Section 2.3.1 and Section 2.3.2 show how this can be
ensured.
2.3.1. Computing Candidate Node-protecting PQ-Nodes for Primary
nexthops
To choose a node-protecting R-LFA nexthop for a destination R3,
router S needs to consider a PQ-node from the candidate node-
protecting PQ-space for the primary nexthop E on shortest path from S
to R3. As mentioned in Section 2.2.2, to consider a PQ-node as
candidate node-protecting PQ-node, there must be at least one direct
neighbor Ni of S, such that all shortest paths from Ni to the PQ-node
does not traverse primary nexthop node E.
Implementations SHOULD run the inequality in Section 2.2.2 Figure 4
for all direct neighbors, other than primary nexthop node E, to
determine whether a node Y is a candidate node-protecting PQ-node.
Sarkar, et al. Expires July 24, 2017 [Page 9]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
All of the metrics needed by this inequality would have been already
collected from the forward SPFs rooted at each of direct neighbor S,
computed as part of standard LFA [RFC5286] implementation. With
reference to the topology in Figure 2, Table 3 below shows how the
above condition can be used to determine the candidate node-
protecting PQ-space for S-E link (primary nexthop E).
+------------+----------+----------+----------+---------+-----------+
| Candidate | Direct | D_opt | D_opt | D_opt | Condition |
| PQ-node | Nbr (Ni) | (Ni,Y) | (Ni,E) | (E,Y) | Met |
| (Y) | | | | | |
+------------+----------+----------+----------+---------+-----------+
| R2 | N | 2 (N,R2) | 1 (N,E) | 2 | Yes |
| | | | | (E,R2) | |
| R3 | N | 2 (N,R3) | 1 (N,E) | 1 | No |
| | | | | (E,R3) | |
+------------+----------+----------+----------+---------+-----------+
Table 3: Node-protection evaluation for R-LFA repair tunnel to PQ-
node
As seen in the above Table 3, R3 does not meet the node-protecting
extended-p-space inequality and so, while R2 is in candidate node-
protecting PQ space, R3 is not.
Some SPF implementations may also produce a list of links and nodes
traversed on the shortest path(s) from a given root to others. In
such implementations, router S may have executed a forward SPF with
each of its direct neighbors as the SPF root, executed as part of the
standard LFA [RFC5286] computations. So S may re-use the list of
links and nodes collected from the same SPF computations, to decide
whether a node Y is a candidate node-protecting PQ-node or not. A
node Y shall be considered as a node-protecting PQ-node, if and only
if, there is at least one direct neighbor of S, other than the
primary nexthop E, for which, the primary nexthop node E does not
exist on the list of nodes traversed on any of the shortest paths
from the direct neighbor to the PQ-node. Table 4 below is an
illustration of the mechanism with the topology in Figure 2.
Sarkar, et al. Expires July 24, 2017 [Page 10]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
+-----------+-------------------+-----------------+-----------------+
| Candidate | Repair Tunnel | Link-Protection | Node-Protection |
| PQ-node | Path(Repairing | | |
| | router to PQ- | | |
| | node) | | |
+-----------+-------------------+-----------------+-----------------+
| R2 | S->N->R1->R2 | Yes | Yes |
| R2 | S->E->R3->R2 | No | No |
| R3 | S->N->E->R3 | Yes | No |
+-----------+-------------------+-----------------+-----------------+
Table 4: Protection of Remote-LFA tunnel to the PQ-node
As seen in the above Table 4 while R2 is candidate node-protecting
Remote-LFA nexthop for R3 and D2, it is not so for E and D1, since
the primary nexthop E is in the shortest path from R2 to E and D1.
2.3.2. Computing node-protecting paths from PQ-nodes to destinations
Once a computing router finds all the candidate node-protecting PQ-
nodes for a given directly attached primary link, it shall follow the
procedure as proposed in this section, to choose one or more node-
protecting R-LFA paths, for destinations reachable through the same
primary link in the primary SPF graph.
To find a node-protecting R-LFA path for a given destination, the
computing router needs to pick a subset of PQ-nodes from the
candidate node-protecting PQ-space for the corresponding primary
nexthop, such that all the path(s) from the PQ-node(s) to the given
destination remain unaffected in the event of a node failure of the
primary nexthop node. To determine whether a given PQ-node belongs
to such a subset of PQ-nodes, the computing router MUST ensure that
none of the primary nexthop node are found on any of the shortest
paths from the PQ-node to the given destination.
This document proposes an additional forward SPF computation for each
of the PQ-nodes, to discover all shortest paths from the PQ-nodes to
the destination. This will help determine, if a given primary
nexthop node is on the shortest paths from the PQ-node to the given
destination or not. To determine if a given candidate node-
protecting PQ-node provides node-protecting alternate for a given
destination, or not, all the shortest paths from the PQ-node to the
given destination has to be inspected, to check if the primary
nexthop node is found on any of these shortest paths. To compute all
the shortest paths from a candidate node-protecting PQ-node to one
(or more) destination, the computing router MUST run the forward SPF
on the candidate node-protecting PQ-node. Soon after running the
forward SPF, the computer router SHOULD run the inequality in
Sarkar, et al. Expires July 24, 2017 [Page 11]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
Figure 6 below, once for each destination. A PQ-node that does not
qualify the condition for a given destination, does not guarantee
node-protection for the path segment from the PQ-node to the specific
destination.
D_opt(Y,D) < D_opt(Y,E) + Distance_opt(E,D)
Where,
D_opt(A,B) : Distance on most optimum path from A to B.
D : The destination node.
E : The primary nexthop on shortest path from S
to destination.
Y : The node-protecting PQ-node being evaluated
Figure 6: Node-Protecting Condition for PQ-node to Destination
All of the above metric costs except D_opt(Y, D), can be obtained
with forward and reverse SPFs with E(the primary nexthop) as the
root, run as part of the regular LFA and Remote-LFA implementation.
The Distance_opt(Y, D) metric can only be determined by the
additional forward SPF run with PQ-node Y as the root. With
reference to the topology in Figure 2, Table 5 below shows how the
above condition can be used to determine node-protection with node-
protecting PQ-node R2.
+-------------+------------+---------+--------+---------+-----------+
| Destination | Primary-NH | D_opt | D_opt | D_opt | Condition |
| (D) | (E) | (Y, D) | (Y, E) | (E, D) | Met |
+-------------+------------+---------+--------+---------+-----------+
| R3 | E | 1 | 2 | 1 | Yes |
| | | (R2,R3) | (R2,E) | (E,R3) | |
| E | E | 2 | 2 | 0 (E,E) | No |
| | | (R2,E) | (R2,E) | | |
| D1 | E | 3 | 2 | 1 | No |
| | | (R2,D1) | (R2,E) | (E,D1) | |
| D2 | E | 2 | 2 | 1 | Yes |
| | | (R2,D2) | (R2,E) | (E,D2) | |
+-------------+------------+---------+--------+---------+-----------+
Table 5: Node-protection evaluation for R-LFA path segment between
PQ-node and destination
As seen in the above example above, R2 does not meet the node-
protecting inequality for destination E, and D1. And so, once again,
while R2 is a node-protecting Remote-LFA nexthop for R3 and D2, it is
not so for E and D1.
Sarkar, et al. Expires July 24, 2017 [Page 12]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
In SPF implementations that also produce a list of links and nodes
traversed on the shortest path(s) from a given root to others, the
inequality in Figure 6 above need not be evaluated. Instead, to
determine whether a PQ-node provides node-protection for a given
destination or not, the list of nodes computed from forward SPF run
on the PQ-node, for the given destination, SHOULD be inspected. In
case the list contains the primary nexthop node, the PQ-node does not
provide node-protection. Else, the PQ-node guarantees node-
protecting alternate for the given destination. Below is an
illustration of the mechanism with candidate node-protecting PQ-node
R2 in the topology in Figure 2.
+-------------+-----------------+-----------------+-----------------+
| Destination | Shortest Path | Link-Protection | Node-Protection |
| | (Repairing | | |
| | router to PQ- | | |
| | node) | | |
+-------------+-----------------+-----------------+-----------------+
| R3 | R2->R3 | Yes | Yes |
| E | R2->R3->E | Yes | No |
| D1 | R2->R3->E->D1 | Yes | No |
| D2 | R2->R3->D2 | Yes | Yes |
+-------------+-----------------+-----------------+-----------------+
Table 6: Protection of Remote-LFA path between PQ-node and
destination
As seen in the above example while R2 is candidate node-protecting
R-LFA nexthop for R3 and D2, it is not so for E and D1, since the
primary nexthop E is in the shortest path from R2 to E and D1.
The procedure described in this document helps no more than to
determine whether a given Remote-LFA alternate provides node-
protection for a given destination or not. It does not find out any
new Remote-LFA alternate nexthops, outside the ones already computed
by standard Remote-LFA procedure. However, in case of availability
of more than one PQ-node (Remote-LFA alternates) for a destination,
and node-protection is required for the given primary nexthop, this
procedure will eliminate the PQ-nodes that do not provide node-
protection and choose only the ones that does.
2.3.3. Computing Node-Protecting R-LFA Paths for Destinations with ECMP
primary nexthop nodes
In certain scenarios, when one or more destinations maybe reachable
via multiple ECMP (equal-cost-multi-path) nexthop nodes, and only
link-protection is required, there is no need to compute any
alternate paths for such destinations. In the event of failure of
Sarkar, et al. Expires July 24, 2017 [Page 13]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
one of the nexthop links, the remaining primary nexthops shall always
provide link-protection. However, if node-protection is required,
the rest of the primary nexthops may not guarantee node-protection.
Figure 7 below shows one such example topology.
D1
2 /
S---x---E1
/ \ / \
/ x / \
/ \ / \
N-------E2 R3--D2
\ 2 /
\ /
\ /
R1-------R2
2
Primary Nexthops:
Destination D1 = [{ S-E1, E1}, {S-E2, E2}]
Destination D2 = [{ S-E1, E1}, {S-E2, E2}]
Figure 7: Topology with multiple ECMP primary nexthops
In the above example topology, costs of all links are 1, except the
following links:
Link: S-E1, Cost: 2
Link: N-E2: Cost: 2
Link: R1-R2: Cost: 2
In the above topology, on computing router S, destinations D1 and D2
are reachable via two ECMP nexthop nodes E1 and E2. However the
primary paths via nexthop node E2 also traverses via the nexthop node
E1. So in the event of node failure of nexthop node E1, both primary
paths (via E1 and E2) becomes unavailable. Hence if node-protection
is desired for destinations D1 and D2, alternate paths that does not
traverse any of the primary nexthop nodes E1 and E2, need to be
computed. In the above topology the only alternate neighbor N does
not provide such a LFA alternate path. Hence one (or more) R-LFA
node-protecting alternate paths for destinations D1 and D2, needs to
be computed.
In the above topology, following are the link-protecting PQ-nodes.
Sarkar, et al. Expires July 24, 2017 [Page 14]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
Primary Nexthop: E1, Link-Protecting PQ-Node: { R2 }
Primary Nexthop: E2, Link-Protecting PQ-Node: { R2 }
To find one (or more) node-protecting R-LFA paths for destinations D1
and D2, one (or more) node-protecting PQ-node(s) needs to be
determined first. Inequalities specified in Section 2.2.6.2 and
Section 2.2.6.3 can be evaluated to compute the node-protecting PQ-
space for each of the nexthop nodes E1 and E2, as shown in Table 7
below. To select a PQ-node as node-protecting PQ-node for a
destination with multiple primary nexthop nodes, the PQ-node MUST
satisfy the inequality for all primary nexthop nodes. Any PQ-node
which is NOT node-protecting PQ-node for all the primary nexthop
nodes, MUST NOT be chosen as the node-protecting PQ-node for
destination.
+--------+----------+-------+--------+--------+---------+-----------+
| Primar | Candidat | Direc | D_opt | D_opt | D_opt | Condition |
| y Next | e PQ- | t Nbr | (Ni,Y) | (Ni,E) | (E,Y) | Met |
| hop | node (Y) | (Ni) | | | | |
| (E) | | | | | | |
+--------+----------+-------+--------+--------+---------+-----------+
| E1 | R2 | N | 3 | 3 | 2 | Yes |
| | | | (N,R2) | (N,E1) | (E1,R2) | |
| E2 | R2 | N | 3 | 2 | 3 | Yes |
| | | | (N,R2) | (N,E2) | (E2,R2) | |
+--------+----------+-------+--------+--------+---------+-----------+
Table 7: Computing Node-protected PQ-nodes for nexthop E1 and E2
In SPF implementations that also produce a list of links and nodes
traversed on the shortest path(s) from a given root to others, the
tunnel-repair paths from the computing router to candidate PQ-node
can be examined to ensure that none of the primary nexthop nodes is
traversed. PQ-nodes that provide one (or more) Tunnel-repair
paths(s) that does not traverse any of the primary nexthop nodes, are
to be considered as node-protecting PQ-nodes. Table 8 below shows
the possible tunnel-repair paths to PQ-node R2.
+--------------+------------+-------------------+-------------------+
| Primary-NH | PQ-Node | Tunnel-Repair | Exclude All |
| (E) | (Y) | Paths | Primary-NH |
+--------------+------------+-------------------+-------------------+
| E1, E2 | R2 | S==>N==>R1==>R2 | Yes |
+--------------+------------+-------------------+-------------------+
Table 8: Tunnel-Repair paths to PQ-node R2
Sarkar, et al. Expires July 24, 2017 [Page 15]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
From Table 7 and Table 8, in the above example, R2 being node-
protecting PQ-node for both primary nexthops E1 and E2, should be
chosen as the node-protecting PQ-node for destinations D1 and D2 that
are both reachable via primary nexthop nodes E1 and E2.
Next, to find a node-protecting R-LFA path from node-protecting PQ-
node to destinations D1 and D2, inequalities specified in Figure 6
should be evaluated, to ensure if R2 provides a node-protecting R-LFA
path for each of these destinations, as shown below in Table 9. For
a R-LFA path to qualify as node-protecting R-LFA path for a
destination with multiple ECMP primary nexthop nodes, the R-LFA path
from the PQ-node to the destination MUST satisfy the inequality for
all primary nexthop nodes.
+----------+----------+-------+--------+--------+--------+----------+
| Destinat | Primary- | PQ- | D_opt | D_opt | D_opt | Conditio |
| ion (D) | NH (E) | Node | (Y, D) | (Y, E) | (E, D) | n Met |
| | | (Y) | | | | |
+----------+----------+-------+--------+--------+--------+----------+
| D1 | E1 | R2 | 3 (R2, | 2 (R2, | 1 (E1, | No |
| | | | D1) | E1) | D1) | |
| D1 | E2 | R2 | 3 (R2, | 3 (R2, | 2 (E2, | Yes |
| | | | D1) | E2) | D1) | |
| D2 | E1 | R2 | 2 (R2, | 2 (R2, | 2 (E1, | Yes |
| | | | D2) | E1) | D2) | |
| D2 | E2 | R2 | 2 (R2, | 2 (R2, | 3 (E2, | Yes |
| | | | D2) | E2) | D2) | |
+----------+----------+-------+--------+--------+--------+----------+
Table 9: Finding node-protecting R-LFA path for destinations D1 and
D2
In SPF implementations that also produce a list of links and nodes
traversed on the shortest path(s) from a given root to others, the
R-LFA paths via node-protecting PQ-node to final destination can be
examined to ensure that none of the primary nexthop nodes is
traversed. R-LFA path(s) that does not traverse any of the primary
nexthop nodes, guarantees node-protection in the event of failure of
any of the primary nexthop nodes. Table 10 below shows the possible
R-LFA-paths for destinations D1 and D2 via the node-protecting PQ-
node R2.
Sarkar, et al. Expires July 24, 2017 [Page 16]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
+-------------+------------+---------+-----------------+------------+
| Destination | Primary-NH | PQ-Node | R-LFA Paths | Exclude |
| (D) | (E) | (Y) | | All |
| | | | | Primary-NH |
+-------------+------------+---------+-----------------+------------+
| D1 | E1, E2 | R2 | S==>N==>R1==>R2 | No |
| | | | -->R3-->E1-->D1 | |
| | | | | |
| D2 | E1, E2 | R2 | S==>N==>R1==>R2 | Yes |
| | | | -->R3-->D2 | |
+-------------+------------+---------+-----------------+------------+
Table 10: R-LFA paths for destinations D1 and D2
From Table 9 and Table 10, in the example above, the R-LFA path from
R2 does not meet the node-protecting inequality for destination D1,
while it does meet the same inequality for destination D2. And so,
while R2 provides node-protecting R-LFA alternate for D2, it fails to
provide node-protection for destination D1. Finally, while it is
possible to get a node-protecting R-LFA path for D2, no such node-
protecting R-LFA path can be found for D1.
2.3.4. Limiting extra computational overhead
In addition to the extra reverse SPF computations suggested by the
Remote-LFA [RFC7490] draft (one reverse SPF for each of the directly
connected neighbors), this document proposes a forward SPF
computations for each PQ-node discovered in the network. Since the
average number of PQ-nodes found in any network is considerably more
than the number of direct neighbors of the computing router, the
proposal of running one forward SPF per PQ-node may add considerably
to the overall SPF computation time.
To limit the computational overhead of the approach proposed, this
document specifies that implementations MUST choose a subset from the
entire set of PQ-nodes computed in the network, with a finite limit
on the number of PQ-nodes in the subset. Implementations MUST choose
a default value for this limit and may provide user with a
configuration knob to override the default limit. This document
suggests 16 as a default value for this limit. Implementations MUST
also evaluate some default preference criteria while considering a
PQ-node in this subset. The exact default preference criteria to be
used is outside the scope of this document, and is a matter of
implementation. Finally, implementations MAY also allow the user to
override the default preference criteria, by providing a policy
configuration for the same.
Sarkar, et al. Expires July 24, 2017 [Page 17]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
This document proposes that implementations SHOULD use a default
preference criteria for PQ-node selection which will put a score on
each PQ-node, proportional to the number of primary interfaces for
which it provides coverage, its distance from the computing router,
and its router-id (or system-id in case of IS-IS). PQ-nodes that
cover more primary interfaces SHOULD be preferred over PQ-nodes that
cover fewer primary interfaces. When two or more PQ-nodes cover the
same number of primary interfaces, PQ-nodes which are closer (based
on metric) to the computing router SHOULD be preferred over PQ-nodes
farther away from it. For PQ-nodes that cover the same number of
primary interfaces and are the same distance from the computing
router, the PQ-node with smaller router-id (or system-id in case of
IS-IS) SHOULD be preferred.
Once a subset of PQ-nodes is found, computing router shall run a
forward SPF on each of the PQ-nodes in the subset to continue with
procedures proposed in Section 2.3.2.
3. Manageability of Remote-LFA Alternate Paths
3.1. The Problem
With the regular Remote-LFA [RFC7490] functionality the computing
router may compute more than one PQ-node as usable Remote-LFA
alternate nexthops. Additionally an alternate selection policy may
be configured to enable the network operator to choose one of them as
the most appropriate Remote-LFA alternate. For such policy-based
alternate selection to run, all the relevant path characteristics for
each the alternate paths (one through each of the PQ-nodes), needs to
be collected. As mentioned before in Section 2.3 the R-LFA alternate
path through a given PQ-node to a given destination is comprised of
two path segments.
The first path segment (i.e. from the computing router to the PQ-
node) can be calculated from the regular forward SPF done as part of
standard and remote LFA computations. However without the mechanism
proposed in section Section 2.3.2 of this document, there is no way
to determine the path characteristics for the second path segment
(i.e. from the PQ-node to the destination). In the absence of the
path characteristics for the second path segment, two Remote-LFA
alternate paths may be equally preferred based on the first path
segments characteristics only, although the second path segment
attributes may be different.
Sarkar, et al. Expires July 24, 2017 [Page 18]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
3.2. The Solution
The additional forward SPF computation proposed in Section 2.3.2
document shall also collect links, nodes and path characteristics
along the second path segment. This shall enable collection of
complete path characteristics for a given Remote-LFA alternate path
to a given destination. The complete alternate path characteristics
shall then facilitate more accurate alternate path selection while
running the alternate selection policy.
As already specified in Section 2.3.4 to limit the computational
overhead of the proposed approach, forward SPF computations must be
run on a selected subset from the entire set of PQ-nodes computed in
the network, with a finite limit on the number of PQ-nodes in the
subset. The detailed suggestion on how to select this subset is
specified in the same section. While this limits the number of
possible alternate paths provided to the alternate-selection policy,
this is needed to keep the computational complexity within affordable
limits. However if the alternate-selection policy is very
restrictive this may leave few destinations in the entire topology
without protection. Yet this limitation provides a necessary
tradeoff between extensive coverage and immense computational
overhead.
4. Acknowledgements
Many thanks to Bruno Decraene for providing his useful comments. We
would also like to thank Uma Chunduri for reviewing this document and
providing valuable feedback. Also, many thanks to Harish Raghuveer
for his review and comments on the initial versions of this document.
5. IANA Considerations
N/A. - No protocol changes are proposed in this document.
6. Security Considerations
This document does not introduce any change in any of the protocol
specifications. It simply proposes to run an extra SPF rooted on
each PQ-node discovered in the whole network.
7. References
7.1. Normative References
Sarkar, et al. Expires July 24, 2017 [Page 19]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
.
[RFC5286] Atlas, A., Ed. and A. Zinin, Ed., "Basic Specification for
IP Fast Reroute: Loop-Free Alternates", RFC 5286,
DOI 10.17487/RFC5286, September 2008,
.
[RFC7490] Bryant, S., Filsfils, C., Previdi, S., Shand, M., and N.
So, "Remote Loop-Free Alternate (LFA) Fast Reroute (FRR)",
RFC 7490, DOI 10.17487/RFC7490, April 2015,
.
7.2. Informative References
[RFC7916] Litkowski, S., Ed., Decraene, B., Filsfils, C., Raza, K.,
Horneffer, M., and P. Sarkar, "Operational Management of
Loop-Free Alternates", RFC 7916, DOI 10.17487/RFC7916,
July 2016, .
Authors' Addresses
Pushpasis Sarkar (editor)
Individual Contributor
Email: pushpasis.ietf@gmail.com
Shraddha Hegde
Juniper Networks, Inc.
Electra, Exora Business Park
Bangalore, KA 560103
India
Email: shraddha@juniper.net
Chris Bowers
Juniper Networks, Inc.
1194 N. Mathilda Ave.
Sunnyvale, CA 94089
US
Email: cbowers@juniper.net
Sarkar, et al. Expires July 24, 2017 [Page 20]
Internet-Draft R-LFA Node-Protection and Manageability January 2017
Hannes Gredler
RtBrick, Inc.
Email: hannes@rtbrick.com
Stephane Litkowski
Orange
Email: stephane.litkowski@orange.com
Sarkar, et al. Expires July 24, 2017 [Page 21]