Network Working Group G. Sidebottom, L. Ong, Guy Mousseau INTERNET-DRAFT Nortel Networks Ian Rytina Ericsson Hanns-Juergen Schwarzbauer Siemens Ken Morneault Cisco Mallesh Kalla Telcordia Normand Glaude Performance Technologies Expires in six months June 2000 SS7 MTP3-User Adaptation Layer (M3UA) Status of This Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC 2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as 'work in progress.' The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. To learn the current status of any Internet-Draft, please check the '1id-abstracts.txt' listing contained in the Internet- Drafts Shadow Directories on ftp.is.co.za (Africa), nic.nordu.net (Europe), munnari.oz.au (Pacific Rim), ftp.ietf.org (US East Coast), or ftp.isi.edu (US West Coast). Abstract This Internet Draft defines a protocol for supporting the transport of any SS7 MTP3-User signalling (e.g., ISUP and SCCP messages) over IP using the services of the Stream Control Transmission Protocol. Also, provision is made for protocol elements that enable a seamless operation of the MTP3-User peers in the SS7 and IP domains. This protocol would be used between a Signalling Gateway (SG) and a Media Gateway Controller (MGC) or IP-resident Database. It is assumed that the SG receives SS7 signalling over a standard SS7 interface using the SS7 Message Transfer Part (MTP) to provide transport. Sidebottom et al [Page 1] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 TABLE OF CONTENTS 1. Introduction.......................................................3 1.1 Scope.........................................................3 1.2 Terminology...................................................3 1.3 M3UA Overview.................................................5 1.4 Functional Areas.............................................10 1.5 Sample Configurations........................................18 1.6 Definition of M3UA Boundaries................................21 2. Conventions.......................................................22 3. M3UA Protocol Elements............................................22 3.1 Common Message Header........................................22 3.2 Transfer Messages............................................24 3.3 SS7 Signalling Network management (SSNM) Messages............26 3.4 Application Server Process Maintenance Messages..............32 3.5 Management Messages..........................................40 4. Procedures........................................................44 4.1 Procedures to Support the Services of the M3UA Layer.........44 4.2 Procedures to Support the M3UA Services in Section 1.4.2.....44 4.3 Procedures to Support the M3UA Services in Section 1.4.4.....45 4.4 Procedures to Support the M3UA Services in Section 1.4.3.....52 5. Examples of M3UA Procedures.......................................54 5.1 Establishment of Association and Traffic Between SGs and ASPs.........................................54 5.2 ASP traffic Fail-over Examples...............................56 5.3 M3UA/MTP3-User Boundary Examples.............................57 6. Security..........................................................61 6.1 Introduction.................................................61 6.2 Threats......................................................61 6.3 Protecting Confidentiality...................................62 7. IANA Considerations...............................................62 8. Acknowledgements..................................................62 9. References........................................................62 10. Author's Addresses...............................................65 Sidebottom et al [Page 2] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 1. Introduction 1.1 Scope There is a need for SCN signalling protocol delivery from an SS7 Signalling Gateway (SG) to a Media Gateway Controller (MGC) or IP- resident Database as described in the Framework Architecture for Signalling Transport [1]. The delivery mechanism should meet the following criteria: * Support for the transfer of all SS7 MTP3-User Part messages (e.g., ISUP, SCCP, TUP, etc.) * Support for the seamless operation of MTP3-User protocol peers * Support for the management of SCTP transport associations and traffic between an SG and one or more MGCs or IP-resident Databases * Support for MGC or IP-resident Database process fail-over and load- sharing * Support for the asynchronous reporting of status changes to management In simplistic transport terms, the SG will terminate SS7 MTP2 and MTP3 protocols and deliver ISUP, SCCP and/or any other MTP3-User protocol messages over SCTP transport associations to MTP3-User peers in MGCs or IP-resident Databases. 1.2 Terminology Application Server (AS) - A logical entity serving a specific Routing Key. An example of an Application Server is a virtual switch element handling all call processing for a unique range of PSTN trunks, identified by an SS7 DPC/OPC/CIC_range. Another example is a virtual database element, handling all HLR transactions for a particular SS7 DPC/OPC/SCCP_SSN combination. The AS contains a set of one or more unique Application Server Processes, of which one or more is normally actively processing traffic. Application Server Process (ASP) - A process instance of an Application Server. An Application Server Process serves as an active or standby process of an Application Server (e.g., part of a distributed virtual switch or database). Examples of ASPs are processes (or process instances of) MGCs, IP SCPs or IP HLRs. An ASP contains an SCTP end- point and may be configured to process signalling traffic within more than one Application Server. Association - An association refers to an SCTP association. The association provides the transport for MTP3-User protocol data units and M3UA adaptation layer peer messages. IP Server Process (IPSP) û A process instance of an IP-based application. An IPSP is essentially the same as an ASP, except that it Sidebottom et al [Page 3] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 uses MU3A in a peer-to-peer fashion. Conceptually, an IPSP does not use the services of a signalling gateway.Signalling Gateway Process (SGP) û A process instance of a Signalling Gateway. It serves as an active, standby or load-sharing process of a Signalling Gateway. Signalling Process û A process instance that uses M3UA to communicate with other signalling process. An ASP, a signalling gateway process and an IPSP are all signalling processes. Routing Key: A Routing Key describes a set of SS7 parameter and parameter values that uniquely define the range of signalling traffic to be handled by a particular Application Server. For example, where all traffic directed to an SS7 DPC, OPC and ISUP CIC_range(s) or SCCP SSN is to be sent to a particular Application Server, that SS7 data defines the associated Routing Key. Routing Keys are unique in the sense that a received SS7 signalling message cannot be directed to more than one Routing Key. Also, a Routing Key cannot extend across more than a single SS7 DPC, in order to more easily support SS7 Management procedures. It is not necessary for the parameter range values within a particular Routing Key to be contiguous. For example, an ASP could be configured to support call processing for multiple ranges of PSTN trunks that are not represented by contiguous CIC values. Routing Context û An Application Server Process may be configured to process traffic related to more than one Application Server, over a single SCTP Association. At an ASP, the Routing Context parameter uniquely identifies the traffic associated with each Application Server that the ASP is configured to support. There is a 1:1 relationship between a received Routing Context value and a Routing Key entry at the sending node. Therefore the Routing Context can be viewed as an index into a sending node's Message Distribution Table containing the Routing Key entries. Fail-over - The capability to re-route signalling traffic as required to an alternate Application Server Process, or group of ASPs, within an Application Server in the event of failure or unavailability of a currently used Application Server Process. Fail-back may apply upon the return to service of a previously unavailable Application Server Process. Signalling Point Management Cluster (SPMC) - A complete set of Application Servers represented to the SS7 network under the same SS7 Point Code. SPMCs are used to sum the availability / congestion / User_Part status of an SS7 destination point code that is distributed in the IP domain, for the purpose of supporting MTP3 management procedures at an SG. In some cases, the SG itself may also be a member of the SPMC. In this case, the SG availability / congestion / User_Part status must also be taken into account when considering any supporting MTP3 management actions. MTP û The Message Transfer Part of the SS7 protocol Sidebottom et al [Page 4] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 MTP3 û MTP Level 3, the signalling network layer of SS7 MTP3-User - Any protocol normally using the services of the SS7 MTP3 (e.g., ISUP, SCCP, TUP, etc.). Network Appearance û The Network Appearance identifies an SS7 network context for the purposes of logically separating the signalling traffic between the SG and the Application Server Processes over a common SCTP Association. An example is where an SG is logically partitioned to appear as an element in four separate national SS7 networks. A Network Appearance implicitly defines the SS7 Point Code(s), Network Indicator and MTP3 protocol type/variant/version used within a specific SS7 network partition. A physical SS7 route-set or link-set at an SG can appear in only one network appearance. The Network Appearance is not globally significant and requires coordination only between the SG and the ASP. Network Byte Order: Most significant byte first, a.k.a Big Endian. Layer Management û Layer Management is a nodal function that handles the inputs and outputs between the M3UA layer and a local management entity. Host - The computing platform that the ASP process is running on. Stream - A stream refers to an SCTP stream. 1.3 M3UA Overview 1.3.1 Protocol Architecture. The framework architecture that has been defined for SCN signalling transport over IP [1] uses multiple components, including a common signalling transport protocol and an adaptation module to support the services expected by a particular SCN signalling protocol from its underlying protocol layer. Within the framework architecture, this document defines an MTP3-User adaptation module suitable for supporting the transfer of messages of any protocol layer that is identified to the MTP Level 3 layer, in SS7 terms, as a user part. The list of these protocol layers include, but is not limited to, ISDN User Part (ISUP) [2,3,4], Signalling Connection Control Part (SCCP) [5,6,7] and Telephone User Part (TUP) [8]. TCAP [9,10,11] or RANAP [12] messages are transferred transparently by the M3UA as SCCP payload, as they are SCCP-User protocols. It is recommended that the M3UA use the services of the Stream Control Transmission Protocol (SCTP) [13] as the underlying reliable common signalling transport protocol. This is to take advantage of various SCTP features such as: Sidebottom et al [Page 5] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 - Explicit packet-oriented delivery (not stream-oriented); - Sequenced delivery of user messages within multiple streams, with an option for order-of-arrival delivery of individual user messages, - Optional multiplexing of user messages into SCTP datagrams; - Network-level fault tolerance through support of multi-homing at either or both ends of an association; - Resistance to flooding and masquerade attacks; and - Data segmentation to conform to discovered path MTU size. Under certain scenarios, such as back-to-back connections without redundancy requirements, the SCTP functions above may not be necessary. In these cases, it is acceptable to use TCP as the underlying common transport protocol. 1.3.2 Services Provided by the M3UA Layer The M3UA Layer at an ASP provides the equivalent set of primitives at its upper layer to the MTP3-Users as provided by the MTP Level 3 to its local users at an SS7 SEP. In this way, the ISUP and/or SCCP layer at an ASP is unaware that the expected MTP3 services are offered remotely from an MTP3 Layer at an SG, and not by a local MTP3 layer. The MTP3 layer at an SG may also be unaware that its local users are actually remote user parts over M3UA. In effect, the M3UA extends access to the MTP3 layer services to a remote IP-based application. The M3UA does not itself provide the MTP3 services. The M3UA Layer may also be used for point-to-point signalling between two IP Server Processes (IPSPs). In this case, the M3UA provides the same set of primitives and services at its upper layer as the MTP3. However, in this case the expected MTP3 services are not offered remotely from an SG. The MTP3 services are provided but the procedures to support these services are a subset of the MTP3 procedures due to the simplified point-to-point nature of the IPSP to IPSP relationship. 1.3.2.1 Support for the transport of MTP3-User Messages The M3UA provides the transport of MTP-TRANSFER primitives across an established SCTP association between an SG and an ASP and between IPSPs. The MTP-TRANSFER primitives are encoded as MTP3-User messages with attached MTP3 Routing Labels as described in the message format sections of the SCCP and ISUP recommendations. In this way, the SCCP and ISUP messages received from the SS7 network are not re-encoded into a different format for transport to/from the server processes. As well, all the required MTP3 Routing Label information (OPC, DPC, SIO) is available at the ASP and the IPSP as is expected by the MTP3-User protocol layer. The M3UA does not impose a 272-octet user information block limit as specified by the SS7 MTP Level 3 protocol. Larger information blocks Sidebottom et al [Page 6] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 can be accommodated directly by M3UA/SCTP, without the need for an upper layer segmentation/re-assembly procedure as specified in recent SCCP or ISUP versions. However, in the context of an SG, the maximum 272-octet block size must be followed when inter-working to a SS7 network that does not support the transfer of larger information blocks to the final destination. This avoids potential ISUP or SCCP fragmentation requirements at the SG. However, if the SS7 network is provisioned to support the Broadband MTP [20] to the final SS7 destination, the information block size limit may be increased past 272 octets. 1.3.2.2 Native Management Functions The M3UA provides management of the underlying SCTP transport protocol to ensure that SG-ASP and IPSP-IPSP transport is available to the degree called for by the MTP3-User signalling applications. The M3UA provides the capability to indicate errors associated with received M3UA messages and to notify, as appropriate, local management and/or the peer M3UA. 1.3.2.3 Inter-working with MTP3 Network Management Functions At the SG, the M3UA must also provide inter-working with MTP3 management functions to support seamless operation of the user SCN signalling applications in the SS7 and IP domains. This includes: - Providing an indication to MTP3-Users at an ASP that a remote destination in the SS7 network is not reachable. - Providing an indication to MTP3-Users at an ASP that a remote destination in the SS7 network is now reachable. - Providing an indication to MTP3-Users at an ASP that messages to a remote MTP3-User peer in the SS7 network are experiencing SS7 congestion - Providing an indication to MTP3-Users at an ASP that a remote MTP3- User peer is unavailable. The M3UA layer at an ASP may initiate an audit of the availability or the congested state of remote SS7 destinations. This information is requested from the M3UA at the SG. 1.3.2.4 Support for the management of SCTP associations between the SG and ASPs. The M3UA layer at the SG maintains the availability state of all configured remote ASPs, in order to manage the SCTP Associations and the traffic between the SG and ASPs. As well, the active/inactive state of Sidebottom et al [Page 7] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 remote ASPs is also maintained - Active ASPs are those currently receiving traffic from the SG. The M3UA layer may be instructed by local management to establish an SCTP association to a peer M3UA node. This can be achieved using the M- SCTP ESTABLISH primitive to request, indicate and confirm the establishment of an SCTP association with a peer M3UA node. The M3UA layer may also need to inform local management of the status of the underlying SCTP associations using the M-SCTP STATUS request and indication primitive. For example, the M3UA may inform local management of the reason for the release of an SCTP association, determined either locally within the M3UA layer or by a primitive from the SCTP. Also the M3UA layer may need to inform the local management of the change in status of an ASP or AS. This can be achieved using the M-ASP STATUS or M-AS STATUS primitives. 1.3.3 Signalling Network Architecture A Signalling Gateway is used to support the transport of MTP3-User signalling traffic received from the SS7 network to multiple distributed ASPs (e.g., MGCs and IP Databases). Clearly, the M3UA protocol description is not designed to meet any performance and reliability requirements for such transport. However, the conjunction of distributed architecture and redundant networks does allow for reliable transport of signalling traffic over IP. The M3UA protocol is flexible enough to allow its operation and management in a variety of physical configurations, enabling Network Operators to meet their performance and reliability requirements. To meet the stringent SS7 signalling reliability and performance requirements for carrier grade networks, these Network Operators should ensure that no single point of failure is present in the end-to-end network architecture between an SS7 node and an IP-based application. This can typically be achieved through the use of redundant SGs, redundant hosts, and the provision of redundant QOS-bounded IP network paths for SCTP Associations between SCTP End Points. Obviously, the reliability of the SG, the MGC and other IP-based functional elements also needs to be taken into account. The distribution of ASPs within the available Hosts must also be considered. As an example, for a particular Application Server, the related ASPs should be distributed over at least two Hosts. Here is one example of a physical network architecture relevant to SS7 carrier-grade operation, in the IP network domain, shown in Figure 1 below: Sidebottom et al [Page 8] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 SG MGC Host#1 ************** ************** Host#1 = * ********__*__________________________*__******** * = SG1 * * SGP1 *__*_____ _______________*__* ASP1 * * MGC1 * ******** * \ / * ******** * * ********__*______\__/________________*__******** * * * SGP2 *__*_______\/______ _____*__* ASP2 * * * ******** * /\ | | * ******** * * : * / \ | | * : * * ******** * / \ | | * ******** * * * SGPn * * | | | | * * ASPn * * * ******** * | | | | * ******** * ************** | | | | ************** | | \ / Host#2 ************** | | \ / ************** Host#2 = * ********__*_____| |______\/_______*__******** * = SG2 * * SGP1 *__*_________________/\_______*__* ASP1 * * MGC2 * ******** * / \ * ******** * * ********__*_______________/ \_____*__******** * * * SGP2 *__*__________________________*__* ASP2 * * * ******** * * ******** * * : * SCTP Associations * : * * ******** * * ******** * * * SGPn * * * * ASPn * * * ******** * * ******** * ************** ************** Figure 1 û Physical Model In this model, each host has many application processes. In the case of the MGC, an ASP may provide service to one or more application server, and is identified as an SCTP end point. In the case of the SG, a pair of signalling gateway processes may represent, as an example, a single network appearance, serving a signalling point management cluster. This example model can also be applied to IPSP-IPSP signalling. In this case, each IPSP would have its services distributed across 2 hosts or more, and may have multiple server processes on each host. In the example above, each signalling process (SGP, ASP or IPSP) is the end point to more than one SCTP association, leading to many other signalling processes. To support this, a signalling process must be able to support distribution of M3UA messages to many simultaneous active associations. This message distribution function is based on the status of provisioned routing keys, the availability of signalling points in the SS7 network, and the redundancy model (active-standby, load-sharing, n+k) of the remote signalling processes. For carrier grade networks, Operators should ensure that under failure or isolation of a particular signalling process, stable calls or Sidebottom et al [Page 9] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 transactions are not lost. This implies that signalling processes need, in some cases, to share the call or transaction state information with other signalling processes. In the case of ASPs performing call processing, coordination may also be required with the related Media Gateway to transfer the MGC control for a particular trunk termination. However, this sharing or communication is outside the scope of this document. This model serves as an example. M3UA imposes no restrictions as to the exact layout of the network elements, the message distribution algorithms and the distribution of the signalling processes. Instead, it provides a framework and a set of messages that allow for a flexible and scalable signalling network architecture, aiming to provide reliability and performance. 1.4 Functional Areas 1.4.1 Signalling Point Code Representation Within an SS7 network, a Signalling Gateway is charged with representing a set of nodes in the IP domain into the SS7 network for routing purposes. The SG itself, as a physical node in the SS7 network, must be addressable with an SS7 Point Code for MTP3 Management purposes. The SG Point Code will also be used for addressing any local MTP3-Users at the SG such as an SG-resident SCCP function. An SG may be logically partitioned to operate in multiple SS7 network Appearances. In such a case, the SG must be addressable with a Point Code in each network appearance, and must represent a set of nodes in the IP domain into each SS7 network. Alias PCs may also be used within an SG network appearance, but SG MTP3 management messages to/from the SS7 network will not use the alias PCs. The M3UA places no restrictions on the SS7 Point Code representation of an AS. Application servers can be represented under the same PC of the SG, their own individual Point Codes or grouped with other applications for Point Code preservation purposes. A single Point Code may be used to represent the SG and all the ASPs together, if desired. If an ASP or group of ASPs is available to the SS7 network via more than one SG, each with its own Point Code, the ASP(s) can be represented by a Point Code that is separate from any SG Point Code. This allows these SGs to be viewed from the SS7 network as "STPs", each having an ongoing "route" to the same ASP(s). Under failure conditions where an ASP becomes unavailable from one of the SGs, this approach enables MTP3 route management messaging between the SG and SS7 network, allowing simple SS7 re-routing through an alternate SG without changing the Destination Point Code Address of SS7 traffic to the ASPs. Sidebottom et al [Page 10] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 +--------+ | | +------------+ SG 1 +--------------+ +-------+ | SS7 links | "STP" | IP network | ---- | SEP +---+ +--------+ +---/ \ | or | | ASPs | | STP +---+ +--------+ +---\ / +-------+ | | | | ---- +------------+ SG 2 +--------------+ | "STP" | +--------+ Note: there is no SG to SG communication shown, so each SG can be reached only via the direct Linkset from the SS7 network. The following example shows a signalling gateway partitioned into two network appearances. SG +-------+ +---------------+ | SEP +--------------| SS7 Ntwk |M3UA| ---- +-------+ SS7 links | "A" | | / \ |__________| +-----------+ ASPs | | | | \ / +-------+ | SS7 Ntwk | | ---- | SEP +--------------+ "B" | | +-------+ +---------------+ 1.4.2 Message Distribution 1.4.2.1 Address Translation and Mapping at the SG In order to direct messages received from the SS7 MTP3 network to the appropriate IP destination, the SG must perform address translation and mapping functions using information from the received MTP3-User message. To support this message distribution, the SG must maintain the equivalent of a network address translation table, mapping incoming SS7 message information to an Application Server for a particular application and range of traffic. This is accomplished by comparing elements of the incoming SS7 message to provisioned Routing Keys in the SG. These Routing Keys in turn make reference to an Application Server that is enabled by one or more ASP. These ASPs provide dynamic status information to the SG using various management messages defined in the M3UA protocol. Possible SS7 address/routing information that comprise a Routing Key entry includes, for example, the OPC, DPC, SIO found in the MTP3 routing label, or other MTP3-User specific fields such as the ISUP CIC, SCCP subsystem number, or TCAP transaction ID. Some example routing keys are: the DPC alone, the DPC/OPC combination, the DPC/OPC/CIC Sidebottom et al [Page 11] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 combination, or the DPC/SSN combination. The particular information used to define an M3UA Routing Key is application and network dependent, and none of the above examples are mandated. An Application Server contains a list of one or more ASPs that are capable of processing the traffic. This list is assumed to be dynamic, taking into account the availability status of the individual ASPs in the list, configuration changes, and possible fail-over mechanisms. The M3UA protocol includes messages to convey the availability status of the individual ASPs as input to a fail-over mechanism. Normally, one or more ASPs is active in the ASP (i.e., currently processing traffic) but in certain failure and transition cases it is possible that there may not be an active ASP available. Both load- sharing and backup scenarios are supported. When there is no Routing Key match for an incoming SS7 message, a default treatment must be specified. Possible solutions are to provide a default Application Server at the SG that directs all unallocated traffic to a (set of) default ASP(s), or to drop the messages and provide a notification to management. The treatment of unallocated traffic is implementation dependent. 1.4.2.2 Address Translation and Mapping at the ASP In order to direct messages to the SS7 network, the ASP must also perform an address translation and mapping function in order to choose the proper SGP for a given message. This is accomplished by observing elements of the outgoing message, SS7 network status, SGP availability and network appearance configuration tables. A Signalling Gateway contains a list of one or more SGPs that are capable of routing SS7 traffic. As is the case with ASPs, this list can be dynamic, taking into account the availability status of the individual SGPs, configuration changes and fail-over mechanisms. 1.4.3 SS7 and M3UA Interworking In the case of SS7 and M3UA inter-working, the M3UA adaptation layer is designed to provide an extension of the MTP3 defined user primitives. 1.4.3.1 Signalling Gateway SS7 Layers The SG is responsible for terminating MTP Level 3 of the SS7 protocol, and offering an IP-based extension to its users. >From an SS7 perspective, it is expected that the Signalling Gateway (SG) transmits and receives SS7 Message Signalling Units (MSUs) to and from the PSTN over a standard SS7 network interface, using the SS7 Message Sidebottom et al [Page 12] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 Transfer Part (MTP) [14,15,16] to provide reliable transport of the messages. As a standard SS7 network interface, the use of MTP Level 2 signalling links is not the only possibility. ATM-based High Speed Links can also be used with the services of the Signalling ATM Adaptation Layer (SAAL) [17,18]. It is possible for IP-based links to be present, using the services of the MTP2-User Adaptation Layer (M2UA) [19]. These SS7 datalinks may be terminated at a Signalling Transfer Point (STP) or at a Signalling End Point (SEP). Using the services of MTP3, the SG may be capable of communicating with remote SS7 SEPs in a quasi-associated fashion, where STPs may be present in the SS7 path between the SEP and the SG. Where ATM-based High Speed Links are used in the SS7 network, it is possible for the SG to use the services of the MTP-3b [20] for reliable transport to and from an SS7 SEP or STP. The maximum Service Data Unit (SDU) supported by the MTP-3b is 4096 octets compared to the 272-octet maximum of the MTP3. However, for MTP3-Users to take advantage of the larger SDU between MTP3-User peers, network architects should ensure that MTP3-b is used end-to-end between the SG and the SS7-resident peer. 1.4.3.2 SS7 and M3UA Inter-Working at the SG The SG provides a functional inter-working of transport functions between the SS7 network and the IP network by also supporting the M3UA adaptation layer. It allows the transfer of MTP3-User signalling messages to and from an IP-based Application Server Process where the peer MTP3-User protocol layer exists. The Signalling Gateway must maintain knowledge of SS7 node and Signalling Point Management Cluster (SPMC) status in their respective domains in order to perform a seamless inter-working of the IP-based signalling and the SS7 domains. For example, SG knowledge of the availability and/or congestion status of the SPMC and SS7 nodes must be maintained and disseminated in the respective networks, in order to ensure that end-to-end operation is transparent to the communicating SCN protocol peers at the SS7 node and ASP. When the SG determines that the transport of SS7 messages to an SPMC is encountering congestion, the SG may optionally inform the MTP3 route management function (by an implementation-dependent mechanism). This information is used by the MTP3 to mark the route to the affected destination as congested and to trigger MTP Transfer Controlled (TFC) messages to any SS7 SEPs generating traffic to the congested DPC, as per current MTP3 procedures. When the SG determines that the transport of SS7 messages to all ASPs in a particular SPMC is interrupted, then it may similarly optionally inform the MTP3 route management function. This information is used by the MTP3 to mark the route to the affected destination as unavailable, Sidebottom et al [Page 13] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 and in the case of a signalling transfer point, to send MTP Transfer Prohibited (TFP) messages to the relevant adjacent SS7 nodes, according to the local SS7 network procedures. When the SG determines that the transport of SS7 messages to an ASP in a particular SPMC can be resumed, the SG may similarly optionally inform the MTP3 route management function. This information is used by the MTP3 to mark the route to the affected destination as available, and in the case of a signalling transfer point, to send MTP Transfer Allowed (TFA) messages to the relevant adjacent SS7 nodes, according to the local SS7 network procedures. In some SS7 network architectures, sending TFP and TFA messages from the SG into the SS7 network should be suppressed. As an example, in the case where the SG is seen by the adjacent SS7 nodes as an SEP (i.e., in ANSI MTP terms the SG is connected via A-links or F-links), TFP or TFA messages would not normally be expected by the adjacent SS7 node. In the case of SS7 user part management, it is required that the MTP3- User protocols at ASPs receive indications of SS7 signalling point availability, SS7 network congestion and User Part availability as would be expected an SS7 SEP node. To accomplish this, the MTP-PAUSE, MTP- RESUME and MTP-STATUS indication primitives received at the MTP3 upper layer interface at the SG need to be made propagated to the remote MTP3- User lower layer interface at the ASP. These indication primitives are also made available to any existing local MTP3-Users at the SG, if present. It is important to clarify that MTP3 management messages such as TFPs or TFAs received from the SS7 network are not "encapsulated" and sent blindly to the ASPs. Rather, the existing MTP3 management procedures are followed within the MTP3 function of the SG to re-calculate the MTP3 route set status and initiate any required signalling-route-set-test procedures into the SS7 network. Only when an SS7 destination status changes are MTP-PAUSE or MTP-RESUME primitives invoked. These primitives can also be invoked due to local SS7 link set conditions as per existing MTP3 procedures. 1.4.3.2 Application Server A cluster of application servers is responsible for providing the overall support for one or many SS7 upper layers. From an SS7 standpoint, a signalling point management cluster (SPMC) must provide complete support for the upper layer service for a given point code. As an example, such a SPMC providing MGC capabilities must provide complete support for ISUP for a given point code, according to the local SS7 network specifications. This measure is necessary to allow the SG to accurately represent the signalling point on the local SS7 network. Sidebottom et al [Page 14] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 1.4.3.3 IPSP Since IPSPs use M3UA in a point-to-point fashion, there is no concept of routing of messages beyond the remote end. Therefore, SS7 and M3UA inter-working is not necessary for this model. 1.4.4 Redundancy Models The network address translation and mapping function of the M3UA layer supports signalling process fail-over functions in order to support a high availability of call and transaction processing capability. 1.4.4.1 Application Server Redundancy All MTP3-User messages (e.g., ISUP, SCCP) incoming to an SG from the SS7 network are assigned to a unique Application Server, based on the information in the message and the provisioned Routing Keys. The Application Server is, in practical terms a list of all ASPs actively configured to process a range of MTP3-User traffic defined by Routing Keys. One or more ASPs in the list are normally active (i.e., handling traffic) while any others may be unavailable or inactive, to be possibly used in the event of failure or unavailability of the active ASP(s). The fail-over model supports an "n+k" redundancy model, where "n" ASPs is the minimum number of redundant ASPs required to handle traffic and "k" ASPs are available to take over for a failed or unavailable ASP. A "1+1" active/standby redundancy is a subset of this model. A simplex "1+0" model is also supported as a subset, with no ASP redundancy. At the SG, an Application Server list contains active and inactive ASPs to support ASP load-sharing and fail-over procedures. The list of ASPs within a logical Application Server is kept updated in the SG to reflect the active Application Server Process(es). To avoid a single point of failure, it is recommended that a minimum of two ASPs be in the list, resident in separate hosts, and therefore available over different SCTP Associations. For example, in the network shown in Figure 1, all messages to DPC x could be sent to ASP1 in Host1 or ASP1 in Host2. The AS list at SG1 might look like this: Routing Key {DPC=x) - "Application Server #1" ASP1/Host1 û State=Up, Active ASP1/Host2 û State=Up, Inactive In this "1+1" redundancy case, ASP1 in Host1 would be sent any incoming message with DPC=x. ASP1 in Host2 would normally be brought to the active state upon failure of, or loss of connectivity to, ASP1/Host1. In this example, both ASPs are Up, meaning that the related SCTP association and far-end M3UA peer is ready. Sidebottom et al [Page 15] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 The AS List at SG1 might also be set up in load-share mode: Routing Key {DPC=x) - "Application Server #1" ASP1/Host1 û State = Up, Active ASP1/Host2 û State = Up, Active In this case, both the ASPs would be sent a portion of the traffic. For example the two ASPs could together form a database, where incoming queries may be sent to any active ASP. Care must be exercised by a Network Operator in the selection of the routing information to be used as the Routing Key for a particular AS. For example, where Application Servers are defined using ranges of ISUP CIC values, the Operator is implicitly splitting up control of the related circuit groups. Some CIC value range assignments may interfere with ISUP circuit group management procedures. Similarly, within an AS, if a load-balancing algorithm were to use CIC values to balance the load across the ASPs, the span of circuit contol assigned to particular ASPs must also be weighed against the ISUP circuit group management procedures. In the process of fail-over or fail-back, it is recommended that in the case of ASPs supporting call processing, stable calls do not fail. It is possible that calls in "transition" may fail, although measures of communication between the ASPs involved can be used to mitigate this. For example, the two ASPs may share call state via shared memory, or may use an ASP to ASP protocol to pass call state information. 1.4.4.2 Signalling Gateway Redundancy Signalling Gateways may also be distributed over multiple hosts. Much like the AS model, SGs are comprised of one or more SG processes (SGP), distributed over one or more hosts, using an active/standby or a load- sharing model. An SGP is viewed as a remote SCTP end-point from an ASP perspective. It is therefore possible for an ASP to route signalling messages destined to the SS7 network using more than one SGP. In this model, a signalling gateway is deployed as a cluster of hosts acting as a single SG. A primary/back-up redundancy model is possible, where the unavailability of the SCTP association to a primary SGP, or the unavailability of the SS7 destination node from the primary SGP, could be used to reroute affected traffic to an alternate SGP. A load-sharing model is possible, where the signalling messages are load-shared between multiple SGPs. It may also be possible for an AS to use more than one SG to access a specific SS7 end point, in a model that resembles an SS7 STP mated pair. Typically, SS7 STPs are deployed in mated pairs, with traffic load- shared between them. Other models are also possible, subject to the limitations of the local SS7 network provisioning guidelines. Sidebottom et al [Page 16] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 >From the perspective of an ASP, a particular SG is capable of transferring traffic to an SS7 destination if an SCTP association with the SGP is established, the SGP has received an indication from the ASP that it is actively handling traffic for that destination, and the SG has not indicated that the destination is inaccessible. When an ASP is configured to use multiple SGPs or SGs for transferring traffic to the SS7 network, the ASP must maintain knowledge of the current capability of the SG to handle traffic to destinations of interest. This information is crucial to the overall reliability of the service, for both active/standby and load-sharing model, in the event of failures, recovery and maintenance activities. The ASP may also use this information for congestion avoidance purposes. 1.4.5 Management Inhibit/Uninhibit Local Management at an ASP or SG may wish to stop traffic across an SCTP association in order to temporarily remove the association from service or to perform testing and maintenance activity. The function could optionally be used to control the start of traffic on to a newly available SCTP association. 1.4.6 Congestion Management The M3UA Layer is informed of local and IP network congestion by means of an implementation-dependent function (e.g., an implementation- dependent indication from the SCTP of IP network congestion). When an SG determines that the transport of SS7 messages to a Signalling Point Management Cluster (SPMC) is encountering congestion, the SG may optionally trigger SS7 MTP3 Transfer Controlled management messages to originating SS7 nodes. The triggering of SS7 MTP3 Management messages from an SG is an implementation-dependent function. At an ASP, congestion is indicated to local MTP3-Users by means of an MTP-Status primitive indicating congestion, to invoke appropriate upper layer responses, as per current MTP3 procedures. 1.4.7 SCTP Stream Mapping. The M3UA at both the SG and ASP also supports the assignment of signalling traffic into streams within an SCTP association. Traffic that requires sequencing must be assigned to the same stream. To accomplish this, MTP3-User traffic may be assigned to individual streams based on the SLS value in the MTP3 Routing Label or the ISUP CIC assignment, subject of course to the maximum number of streams supported by the underlying SCTP association. The use of SCTP streams within M3UA is recommended in order to minimize transmission and buffering delays, therefore improving the overall performance and reliability of the signalling elements. The distribution of the MTP3 user messages over the various streams should be done in such Sidebottom et al [Page 17] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 a way to minimize message mis-sequencing, as required by the SS7 User Parts. 1.4.8 Client/Server Model The SG takes on the role of server while the ASP is the client. ASPs must initiate the SCTP association to the SG. The SCTP (and UDP/TCP) Registered User Port Number Assignment for M3UA is 2905. 1.5 Sample Configurations 1.5.1 Example 1: ISUP message transport ******** SS7 ***************** IP ******** * SEP *---------* SG *--------* ASP * ******** ***************** ******** +------+ +------+ | ISUP | (NIF) | ISUP | +------+ +------+-+------+ +------+ | MTP3 | | MTP3 | | M3UA | | M3UA | +------| +------+ +------+ +------+ | MTP2 | | MTP2 | | SCTP | | SCTP | +------+ +------+ +------+ +------+ | L1 | | L1 | | IP | | IP | +------+ +------+ +------+ +------+ |_______________| |______________| SEP - SS7 Signalling End Point SCTP - Stream Control Transmission Protocol NIF û Nodal Inter-working Function In this example, the SG provides an implementation-dependent nodal inter-working function (NIF) that allows the MGC to exchange SS7 signalling messages with the SS7-based SEP. The NIF within the SG serves to transport messages within the SG between the MTP3 and M3UA. This nodal inter-working function has no visible peer protocol with either the MGC or SEP. It also provides network status information to one or both sides of the network. For internal SG modeling purposes, at the NIF level, SS7 signalling messages that are destined to the MGC are received as MTP-TRANSFER indication primitives from the MTP Level 3 upper layer interface and are sent to the local M3UA-resident message distribution function for ongoing routing to the final IP destination. MTP-TRANSFER primitives received from the local M3UA network address translation and mapping function are sent to the MTP Level 3 upper layer interface as MTP- Sidebottom et al [Page 18] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 TRANSFER request primitives for on-going MTP Level 3 routing to an SS7 SEP. For the purposes of providing SS7 network status information the NIF also delivers MTP-PAUSE, MTP-RESUME and MTP-STATUS indication primitives received from the MTP Level 3 upper layer interface to the local M3UA-resident management function. 1.5.2 Example 2: SCCP Transport between IPSPs ******** IP ******** * IPSP * * IPSP * ******** ******** +------+ +------+ |SCCP- | |SCCP- | | User | | User | +------+ +------+ | SCCP | | SCCP | +------+ +------+ | M3UA | | M3UA | +------+ +------+ | SCTP | | SCTP | +------+ +------+ | IP | | IP | +------+ +------+ |________________| This example shows an architecture where no Signalling Gateway is used. In this example, SCCP messages are exchanged directly between two IP- resident IPSPs with resident SCCP-User protocol instances, such as RANAP or TCAP. SS7 network inter-working is not required, therefore there is no MTP3 network management status information for the SCCP and SCCP-User protocols to consider. Any MTP-PAUSE, -RESUME or -STATUS indications from the M3UA to the SCCP should consider only the status of the SCTP Association and underlying IP network. Sidebottom et al [Page 19] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 1.5.3 Example 3: SG resident SCCP layer, with remote ASP ******** SS7 ***************** IP ******** * SEP *---------* *--------* * * or * * SG * * ASP * * STP * * * * * ******** ***************** ******** +------+ +---------------+ +------+ | SCCP-| | SCCP | | SCCP-| | User | +---------------+ | User | +------+ | _____ | +------+ | SCCP | | | | | | SCCP | +------+ +------+-+------+ +------+ | MTP3 | | MTP3 | | M3UA | | M3UA | +------| +------+ +------+ +------+ | MTP2 | | MTP2 | | SCTP | | SCTP | +------+ +------+ +------+ +------+ | L1 | | L1 | | IP | | IP | +------+ +------+ +------+ +------+ |_______________| |______________| STP - SS7 Signalling Transfer Point In this example, the SG contains an instance of the SS7 SCCP protocol layer that may, for example, perform the SCCP Global Title Translation (GTT) function for messages logically addressed to the SG SCCP. If the result of a GTT for an SCCP message yields an SS7 DPC or DPC/SSN address result of an SCCP peer located in the IP domain, the resulting MTP- TRANSFER request primitive is sent to the local M3UA-resident network address translation and mapping function for ongoing routing to the final IP destination. Similarly, the SCCP instance in an SG can perform the SCCP GTT service for messages logically addressed to it from SCCP peers in the IP domain. In this case, MTP-TRANSFER messages are sent from the local M3UA- resident network address translation and mapping function to the SCCP for GTT. If the result of the GTT yields the address of an SCCP peer in the SS7 network then the resulting MTP-TRANSFER request is given to the MTP3 for delivery to an SS7-resident node. It is possible that the above SCCP GTT at the SG could yield the address of an SCCP peer in the IP domain and the resulting MTP-TRANSFER primitive would be sent back to the M3UA for delivery to an IP destination. For internal SG modeling purposes, this may be accomplished with the use of an implementation-dependent nodal inter-working function within the SG that effectively sits below the SCCP and routes MTP-TRANSFER messages to/from both the MTP3 and the M3UA, based on the SS7 DPC or DPC/SSN Sidebottom et al [Page 20] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 address information. This nodal inter-working function has no visible peer protocol with either the ASP or SEP. Note that the services and interface provided by the M3UA are the same as in Example 1 and the functions taking place in the SCCP entity are transparent to M3UA. The SCCP protocol functions are not reproduced in the M3UA protocol. 1.6 Definition of M3UA Boundaries 1.6.1 Definition of the boundary between M3UA and an MTP3-User. >From ITU Q.701 [2]: MTP-TRANSFER request MTP-TRANSFER indication MTP-PAUSE indication MTP-RESUME indication MTP-STATUS indication 1.6.2 Definition of the boundary between M3UA and SCTP The upper layer primitives provided by the SCTP are provided in [13] 1.6.3 Definition of the Boundary between M3UA and Layer Management M-SCTP ESTABLISH request M-SCTP ESTABLISH indication M-STCP ESTABLISH confirm M-SCTP RELEASE request M-SCTP RELEASE indication M-SCTP RELEASE confirm M-SCTP STATUS request M-SCTP STATUS indication M-ASP STATUS request M-ASP STATUS indication M-AS-STATUS request M-AS-STATUS indication M-NOTIFY indication M-ERROR indication M-ASP-INHIBIT request M-ASP-UNINHIBIT request Sidebottom et al [Page 21] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 2.0 Conventions The keywords MUST, MUST NOT, REQUIRED, SHALL, SHALL NOT, SHOULD, SHOULD NOT, RECOMMENDED, NOT RECOMMENDED, MAY, and OPTIONAL, when they appear in this document, are to be interpreted as described in [RFC2119]. 3.0 M3UA Protocol Elements The general M3UA message format includes a Common Message Header followed by zero or more parameters as defined by the Message Type. For forward compatibility, all Message Types may have attached parameters even if none are specified in this version. 3.1 Common Message Header The protocol messages for MTP3-User Adaptation require a message structure that contains a version, message type, message length, and message contents. This message header is common among all signalling protocol adaptation layers: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Version | Reserved | Message Class | Message Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Message Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | All fields in an M3UA message MUST be transmitted in the network byte order, unless otherwise stated. M3UA Protocol Version: 8 bits (unsigned integer) The version field contains the version of the M3UA adaptation layer. The supported versions are: Value Version ----- ------- 1 Release 1.0 Sidebottom et al [Page 22] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 Message Class: 8 bits (unsigned integer) The following list contains the Message Type Classes for the defined messages. 0 Management (MGMT) Message 1 Transfer Messages 2 SS7 Signalling Network Management (SSNM) Messages 3 ASP State Maintenance (ASPSM) Messages 4 ASP Traffic Maintenance (ASPTM) Messages 5 to 255 Reserved Message Type: 8 bits (unsigned integer) The following list contains the message types for the defined messages. Management (MGMT) Message 0 Error (ERR) 1 Notify (NTFY) 2 to 255 Reserved for Management Messages Transfer Messages 0 Reserved 1 Payload Data (DATA) 2 to 255 Reserved for Transfer Messages SS7 Signalling Network Management (SSNM) Messages 0 SS7 Network Isolation (S7ISO) 1 Destination Unavailable (DUNA) 2 Destination Available (DAVA) 3 Destination State Audit (DAUD) 4 SS7 Network Congestion State (SCON) 5 Destination User Part Unavailable (DUPU) 6 to 255 Reserved for SSNM Messages ASP State Maintenance (ASPSM) Messages 0 Reserved 1 ASP Up (UP) 2 ASP Down (DOWN) 3 Heartbeat (HEARTBEAT) 4 ASP Up Ack (UP ACK) 5 ASP Down Ack (DOWN ACK) 6 to 255 Reserved for ASPSM Messages Sidebottom et al [Page 23] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 ASP Traffic Maintenance (ASPTM) Messages 0 Reserved 1 ASP Active (ACTIVE) 2 ASP Inactive (INACTIVE) 3 ASP Active Ack (ACTIVE ACK) 4 ASP Inactive Ack (INACTIVE ACK) 5 to 255 Reserved for ASPTM Messages Reserved: 5 bits Should be set to all '0's and ignored by the receiver. Message Length: 32-bits (unsigned integer) The Message Length defines the length of the message in octets, not including the header. 3.2 Variable-Length Parameter Format M3UA messages consist of a Common Header followed by zero or more variable-length parameters, as defined by the message type. The variable-length parameters contained in a message are defined in a Tag- Length-Value format as shown below. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Parameter Tag | Parameter Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Parameter Value / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Parameter Tag: 16 bits (unsigned integer) Tag field is a 16-bit identifier of the type of parameter. It takes a value of 0 to 65534. The value of 65535 is reserved for IETF-defined extensions. Values other than those defined in specific parameter description are reserved for use by the IETF. Parameter Length: 16 bits (unsigned integer) The Parameter Length field contains the size of the parameter in bytes, including the Parameter Tag, Parameter Length, and Parameter Value fields. The Parameter Length does not include any padding bytes. Sidebottom et al [Page 24] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 Parameter Value: variable-length. The Parameter Value field contains the actual information to be transferred in the parameter. The total length of a parameter (including Tag, Parameter Length and Value fields) MUST be a multiple of 4 bytes. If the length of the parameter is not a multiple of 4 bytes, the sender pads the Parameter at the end (i.e., after the Parameter Value field) with all zero bytes. The length of the padding is NOT included in the parameter length field. A sender should NEVER pad with more than 3 bytes. The receiver MUST ignore the padding bytes. 3.2 Transfer Messages The following section describes the Transfer messages and parameter contents. 3.2.1 Payload Data Message (DATA) The Data message contains the SS7 MTP3-User protocol data, which is an MTP-TRANSFER primitive, including the complete MTP3 Routing Label. The Data message contains the following variable length parameters: Network Appearance Optional Protocol Data Mandatory The following format MUST be used for the Data Message: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 1 | Length = 8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Network Appearance* | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 3 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ / Protocol Data / \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Network Appearance: 32-bits (unsigned integer) The optional Network Appearance parameter identifies the SS7 network context for the message, for the purposes of logically separating the Sidebottom et al [Page 25] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 signalling traffic between the SG and the Application Server Process over a common SCTP Association. An example is where an SG is logically partitioned to appear as an element in four different national SS7 networks. In a Data message, the Network Appearance defines the SS7 Point Codes used, the SS7 Network Indicator value and MTP3/MTP3-User protocol type/variant/version used within the SS7 network partition. Where an SG operates in the context of a single SS7 network, or individual SCTP associations are dedicated to each SS7 network context, or the Network Indicator in the SIO of the MTP-Transfer primitive is sufficient, the Network Appearance parameter is not required. The Network Appearance parameter value assigned according to network operator policy. The values used are of local significance only, coordinated between the SG and ASP. Where the optional Network Appearance parameter is present, it must be the first parameter in the message as it defines the format of the Protocol Data field. Protocol Data: variable length The Protocol Data field contains the MTP3-User application message, which is in effect an MTP-TRANSFER primitive. As defined for a specific value of the Protocol Identifier, this will include the MTP- User Data and includes the MTP Routing Label (SS7 OPC, DPC, SLS), and the SIO (Service Indicator, Network Indicator & optional Message Priority codes). Note: in the case of ISUP messages, the Circuit Identification Code is also included. 3.3 SS7 Signalling Network Management (SSNM) Messages 3.3.1 Destination Unavailable (DUNA) The DUNA message is sent from the SG to all concerned ASPs to indicate that the SG has determined that one or more SS7 destinations are unreachable. The MTP3-User at the ASP is expected to stop traffic to the affected destination through the SG initiating the DUNA as per the defined MTP3-User procedures. The DUNA message contains the following parameters: Network Appearance Optional Affected Destination Mandatory Info String Optional Sidebottom et al [Page 26] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 The format for DUNA Message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 1 | Length =8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Network Appearance* | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 5 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask | Affected DPC 1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | ... | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask | Affected DPC n | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 4 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | INFO String* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Network Appearance: 32-bit unsigned integer The optional Network Appearance parameter identifies the SS7 network context for the message, for the purposes of logically separating the signalling traffic between the SG and the Application Server Process over a common SCTP Association. An example is where an SG is logically partitioned to appear as an element in four different national SS7 networks. In an SSNM message, the Network Appearance parameter defines the format of the Affected DPC(s) in the Affected Destination parameter. The DPC point code length (e.g., 14-, 16-, or 24-bit) and sub-field definitions (e.g., ANSI 24-bit network/cluster/member, ITU-international 14-bit zone/region/signal_point, many national field variants, ...) are fixed within a particular Network Appearance. Where an SG operates in the context of a single SS7 network, or individual SCTP associations are dedicated to each SS7 network context, the Network Appearance parameter is not required and the format of the Affected DPC(s) is understood implicitly. The format of the Network Appearance parameter is an integer, the values of which are assigned according to network operator policy. The values used are of local significance only, coordinated between the SG and ASP. Sidebottom et al [Page 27] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 Where the optional Network Appearance parameter is present, it must be the first parameter in the message as it defines the format of the Affected DPCs in the Affected Destination parameter. Affected Destination: 24-bits The Affected Destination parameter contains one or more Affected Destination Point Codes, each a three-octet parameter to allow for 14-, 16- and 24-bit binary formatted SS7 Point Codes. Affected Point Codes that are less than 24-bits, are padded on the left to the 24-bit boundary. The encoding is shown below for ANSI and ITU Point Code examples. ANSI 24-bit Point Code: 0 1 2 3-----> 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask | Network | Cluster | Member | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |MSB-----------------------------------------LSB| ITU 14-bit Point Code: 0 1 2 3-----> 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Mask |0 0 0 0 0 0 0 0 0 0|Zone | Region | SP | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |MSB--------------------LSB| It is optional to send an Affected Destination parameter with more than one Affected DPC but it is mandatory to receive it. All the Affected DPCs included must be within the same Network Appearance. Including multiple Affected DPCs may be useful when reception of an MTP3 management message or a linkset event simultaneously affects the availability status of a list of destinations at an SG. Mask: 8-bits The Mask parameter is used to identify a contiguous range of Affected Destination Point Codes, independent of the point code format. Identifying a contiguous range of Affected DPCs may be useful when reception of an MTP3 management message or a linkset event simultaneously affects the availability status of a series of destinations at an SG. For example, if all DPCs in an ANSI cluster are determined to be unavailable due to local linkset unavailability, the DUNA could identify potentially 256 Affected DPCs in a single Affected DPC field. Sidebottom et al [Page 28] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 The Mask parameter is an integer representing a bit mask that can be applied to the related Affected DPC field. The bit mask identifies how many bits of the Affected DPC field is significant and which are effectively "wildcarded". For example, a mask of "8" indicates that the last eight bits of the DPC is "wildcarded". For an ANSI 24-bit Affected DPC, this is equivalent to signalling that all DPCs in an ANSI Cluster are unavailable. A mask of "3" indicates that the last three bits of the DPC is "wildcarded". For a 14-bit ITU Affected DPC, this is equivalent to signaling that an ITU Region is unavailable. Info String: variable length The optional INFO String parameter can carry any meaningful 8-BIT ASCII character string along with the message. Length of the INFO String parameter is from 0 to 255 characters. No procedures are presently identified for its use but the INFO String may be used by Operators to identify in text form the location reflected by the Affected DPC for debugging purposes. 3.3.2 Destination Available (DAVA) The DAVA message is sent from the SG to all concerned ASPs to indicate that the SG has determined that one or more SS7 destinations are now reachable. The ASP MTP3-User protocol is expected to resume traffic to the affected destination through the SG initiating the DUNA. The DAVA message contains the following parameters: Network Appearance Optional Affected Destination Mandatory Info String Optional The format and description of DAVA Message parameters is the same as for the DUNA message (See Section 3.3.2.1.) 3.3.3 Destination State Audit (DAUD) The DAUD message can be sent from the ASP to the SG to audit the availability/congestion state of SS7 routes to one or more affected destinations. See Section 3.4.3 for the audit procedures. The DAUD message contains the following parameters: Network Appearance Optional Affected Destination Mandatory Info String Optional The format and description of DAUD Message parameters is the same as for the DUNA message (See Section 3.3.2.1.) Sidebottom et al [Page 29] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 Multiple Affected Destination Point Codes parameters may optionally be included in a DAUD message. However all the Affected Destination Point Codes must be part of the same Network Appearance. 3.3.4 SS7 Network Congestion (SCON) The SCON message can be sent from the SG to all concerned ASPs to indicate that the congestion level in the SS7 network to one or more destinations has changed. The SCON message contains the following parameters: Network Appearance Optional Affected Destination Mandatory Congestion Level Mandatory Info String Optional The format for SCON Message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 1 | Length =8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Network Appearance* | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 5 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Cong. Level 1 | Affected DPC 1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | ... | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Cong. Level n | Affected DPC n | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 4 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | INFO String* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The format and description of the Network Appearance, Affected Destination and Info String parameters is the same as for the DUNA message (See Section 3.3.2.1.) Sidebottom et al [Page 30] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 Congestion Level: 8-bits (unsigned integer) The valid values for the optional Congestion Level parameter are shown in the following table. 0 No Congestion or Undefined 1 Congestion Level 1 2 Congestion Level 2 3 Congestion Level 3 The congestion levels are as defined in the national congestion method in the ITU MTP recommendation [14] or in the ANSI MTP standard [15]. For MTP congestion methods that do not employ congestion levels (e.g., the ITU international method, the parameter is always "Undefined". 3.3.5 Destination User Part Unavailable (DUPU) The DUPU message is used by an SG to inform an ASP that a remote peer MTP3-User User Part (e.g., ISUP or SCCP) at an SS7 node is unavailable. The DUPU message contains the following parameters: Network Appearance Optional Affected Destination Mandatory Unavailability Cause Mandatory MTP3-User Identity Mandatory Info String Optional The format for DUPU Message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 1 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Network Appearance* | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 5 | Length = 8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Cause | User | Affected Destination | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 4 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | INFO String* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The format and description of the Network Appearance, Affected Destination and Info String parameters is the same as for the DUNA Sidebottom et al [Page 31] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 message (See Section 3.3.2.1.) One exception is that the Affected Desination parameter in the DUPU message can only contain one Affected DPC. Unavailability Cause: 4-bits (unsigned integer) The Unavailability Cause parameter provides the reason for the unavailability of the MTP3-User. The valid values for the Unavailability Cause parameter are shown in the following table. The values agree with those provided in the SS7 MTP3 User Part Unavailable message. Depending on the MTP3 protocol used in the network context, additional values may be used û the specification of the relevant MTP3 protocol variant/version is definitive. 0 Unknown 1 Unequipped Remote User 2 Inaccessible Remote User MTP3-User Identity: 4-bits (unsigned integer) The MTP3-User Identity describes the specific MTP3-User that is unavailable (e.g., ISUP, SCCP, ...). The valid values for the MTP3-User Identity are shown below. The values agree with those provided in the SS7 MTP3 User Part Unavailable message and Service Indicator. Depending on the MTP3 protocol used in the network context, additional values may be used û the specification of the relevant MTP3 protocol variant/version is definitive. Value Description 00 - 02 Reserved 03 SCCP 04 TUP 05 ISUP 06 û 08 Reserved 09 Broadband ISUP 10 Satellite ISUP 3.4 Application Server Process Maintenance (ASPM) Messages 3.4.1 ASP Up (ASPUP) The ASP UP (ASPUP) message is used to indicate to a remote M3UA peer that the Adaptation layer is ready to receive traffic or maintenance messages. The ASPUP message contains the following parameters: Adaptation Layer Identifer Optional Protocol Identifier Optional INFO String Optional Sidebottom et al [Page 32] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 The format for ASPUP Message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 2 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Adaptation Layer Identifier* | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 4 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | INFO String* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The format and description of the optional Info String parameter is the same as for the DUNA message (See Section 3.3.2.1.) Adaptation Layer Identity: 32-bits () The optional Adaptation Layer Identifier (ALI) is a string that identifies the adaptation layer. This string must be set to "M3UA" which results in a length of 8. The ALI would normally only be used in the initial ASP Up message across a new SCTP association to ensure both peers are assuming the same adaptation layer protocol. 3.4.2 ASP Up Ack The ASP UP Ack message is used to acknowledge an ASP-Up message received from a remote M3UA peer. The ASPUP Ack message contains the following parameters: Adaptation Layer Identifier (optional) Protocol Identifier (optional) INFO String (optional) Sidebottom et al [Page 33] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 The format for ASPUP Ack Message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag =2 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | Adaptation Layer Identifier* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag =4 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | INFO String* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The format and description of the optional Info String parameter is the same as for the DUNA message (See Section 3.3.2.1.) The format and description of the optional Adaptation Layer Identifier (ALI) parameter is the same as for the ASP-UP message. (See Section 3.4.1) 3.4.3 ASP Down (ASPDN) The ASP Down (ASPDN) message is used to indicate to a remote M3UA peer that the adaptation layer is not ready to receive traffic or maintenance messages. The ASPDN message contains the following parameters: Reason Mandatory INFO String Optional The format for the ASPDN message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reason | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag =4 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | INFO String* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Sidebottom et al [Page 34] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 The format and description of the optional Info String parameter is the same as for the DUNA message (See Section 3.3.2.1.) Reason: 32-bit (unsigned integer) The Reason parameter indicates the reason that the remote M3UA adaptation layer is unavailable. The valid values for Reason are shown in the following table. 1 Processor Outage 2 Management Inhibit 3.4.4 ASP Down Ack The ASP Down Ack message is used to acknowledge an ASP-Down message received from a remote M3UA peer. The ASP Down Ack message contains the following parameters: Reason Mandatory INFO String Optional The format for the ASPDN Ack message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reason | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 4 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | INFO String* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The format and description of the optional Info String parameter is the same as for the DUNA message (See Section 3.3.2.1.) The format of the Reason parameter is the same as for the ASP-Down message. (See Section 3.4.3) 3.4.5 ASP Active (ASPAC) The ASPAC message is sent by an ASP to indicate to a remote M3UA peer that it is Active and ready to process signalling traffic for a particular Application Server Sidebottom et al [Page 35] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 The ASPAC message contains the following parameters: Type Mandatory Routing Context Optional INFO String Optional The format for the ASPAC message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag =6 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | Routing Context* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 4 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | INFO String* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type: 32-bit (unsigned integer) The Type parameter identifies the traffic mode of operation of the ASP within an AS. The valid values for Type are shown in the following table. 1 Over-ride 2 Load-share Within a particular Routing Context, only one Type can be used. The Over-ride value indicates that the ASP is operating in Over-ride mode, where the ASP takes over all traffic in an Application Server (i.e., primary/back-up operation), over-riding any currently active ASP in the AS. In Load-share mode, the ASP will share in the traffic distribution with any other currently active ASPs. A node that receives an ASPAC with an incorrect Type for a particular Routing Context will respond with an Error Message (Cause: Invalid Traffic Handling Mode. Routing Context: The optional Routing Context parameter contains (a list of) integers indexing the Application Server traffic that the sending ASP is Sidebottom et al [Page 36] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 configured/registered to receive. There is one-to-one relationship between an index entry and an SG Routing Key or AS Name. Because an AS can only appear in one Network Appearance, the Network Appearance parameter is not required in the ASPAC message. An Application Server Process may be configured to process traffic for more than one logical Application Server. From the perspective of an ASP, a Routing Context defines a range of signalling traffic that the ASP is currently configured to receive from the SG. For example, an ASP could be configured to support call processing for multiple ranges of PSTN trunks and therefore receive related signalling traffic, identified by separate SS7 DPC/OPC/CIC_ranges. The format and description of the optional Info String parameter is the same as for the DUNA message (See Section 3.3.2.1.) 3.4.6 ASP Active Ack The ASPAC Ack message is used to acknowledge an ASP-Active message received from a remote M3UA peer. The ASPAC Ack message contains the following parameters: Type Mandatory Routing Context Optional INFO String Optional The format for the ASPAC Ack message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 6 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | Routing Context* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 4 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | INFO String* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Sidebottom et al [Page 37] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 The format and description of the optional Info String parameter is the same as for the DUNA message (See Section 3.3.2.1.) The format of the Type and Routing Context parameters is the same as for the ASP-Active message. (See Section 3.4.5). 3.4.7 ASP Inactive (ASPIA) The ASPIA message is sent by an ASP to indicate to a remote M3UA peer that it is no longer processing signalling traffic within a particular Application Server. The ASPIA message contains the following parameters: Type Mandatory Routing Context Optional INFO String Optional The format for the ASPIA message parameters is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 6 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | Routing Context* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 4 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | INFO String* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The Type parameter identifies the traffic mode of operation of the ASP within an AS. The valid values for Type are shown in the following table. Value Description 0x1 Over-ride 0x2 Load-share Within a particular Routing Context, only one Type can be used. The Over-ride value indicates that the ASP is operating in Over-ride mode, Sidebottom et al [Page 38] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 and will no longer handle traffic within an Application Server (i.e., it is now a backup in a primary/back-up arrangement). The Load-share value indicates that the ASP is operating in Load-share mode and will no longer share in the traffic distribution with any other currently active ASPs. A node that receives an ASPIA with an incorrect Type for a particular Routing Context will respond with an Error Message (Cause: Invalid Traffic Handling Mode. The format and description of the optional Routing Context and Info String parameters is the same as for the ASPAC message (See Section 2.3.3.3.) 3.4.8 ASP Inactive Ack The ASPIA Ack message is used to acknowledge an ASP-Inactive message received from a remote M3UA peer. The ASPIA Ack message contains the following parameters: Type Mandatory Routing Context Optional INFO String Optional The format for the ASPIA Ack message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 6 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | Routing Context* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 4 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | INFO String* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Sidebottom et al [Page 39] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 The format and description of the optional Info String parameter is the same as for the DUNA message (See Section 3.3.2.1.) The format of the Type and Routing Context parameters is the same as for the ASP-Inctive message. (See Section 3.4.7). 3.4.9 Heartbeat (BEAT) The Heartbeat message is optionally used to ensure that the M3UA peers are still available to each other. It is recommended for use when the M3UA runs over a transport layer other than the SCTP, which has its own heartbeat. The BEAT message contains no parameters. 3.5 Management Messages 3.5.1 Error (ERR) The Error message is used to notify a peer of an error event associated with an incoming message. For example, the message type might be unexpected given the current state, or a parameter value might be invalid. The ERR message contains the following parameters: Error Code Mandatory Diagnostic Information Optional The format for the ERR message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Error Code | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 7 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | Diagnostic Information* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Sidebottom et al [Page 40] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 Error Code: 32-bits (unsigned integer) The Error Code parameter indicates the reason for the Error Message. The Error parameter value can be one of the following values: Invalid Version 0x1 Invalid Network Appearance 0x2 Invalid Adaptation Layer Identifier 0x3 Invalid Message Type 0x4 Invalid Traffic Handling Mode 0x5 Unexpected Message Type 0x6 Protocol Error 0x7 Diagnostic Information: variable length When included, the optional Diagnostic information can be any information germane to the error condition, to assist in identification of the error condition. In the case of an Invalid Network Appearance, Adaptation Layer Identifier or Traffic Handling Mode, the Diagnostic information includes the received parameter. In the other cases, the Diagnostic information may be the first 40 bytes of the offending message. In the case of an Invalid Version Error Code, the Common Header contains the supported Version. Error messages are not generated in response to other Error messages. 3.5.2 Notify (NTFY) The Notify message used to provide an autonomous indication of M3UA events to an M3UA peer. The NTFY message contains the following parameters: Status Type Mandatory Status Identification Mandatory Routing Context Optional INFO String Optional Sidebottom et al [Page 41] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 The format for the NTFY message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Status Type | Status Identification | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 6 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | Routing Context* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Tag = 4 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \ \ | INFO String* | \ \ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Status Type: 16-bits (unsigned integer) The Status Type parameter identifies the type of the Notify message. Following are the valid Status Type values: 1 Application Server state change (AS_State_Change) 2 Other Status Information: 16-bits (unsigned integer) The Status Information parameter contains more detailed information for the notification, based on the value of the Status Type. If the Status Type is AS_State_Change the following Status Information values are used: 1 Application Server Down (AS_Down) 2 Application Server Up (AS_Up) 3 Application Server Active (AS_Active) 4 Application Server Pending (AS_Pending) 5 Alternate ASP Active 6 Insufficient ASPs These notifications are sent from an SG to an ASP upon a change in status of a particular Application Server. The value reflects the new state of the Application Server. Sidebottom et al [Page 42] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 If the Status Type is Other, then the following Status Information values are defined: 1 Insufficient ASP resources active in AS This notification is not based on the SG reporting the state change of an ASP or AS. For the value defined the SG is indicating to an ASP(s) in the AS that another ASP is required in order to handle the load of the AS. The format and description of the optional Routing Context and Info String parameters is the same as for the ASPAC message (See Section 3.4.6.) Sidebottom et al [Page 43] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 4.0 Procedures The M3UA layer needs to respond to various local primitives it receives from the SCTP and M3UA-User layers and Layer Management as well as the messages that it receives from the peer M3UA layers. This section describes the M3UA procedures in response to these events. 4.1 Procedures to support the services of the M3UA layer 4.1.1 Receipt of primitives from the M3UA-User On receiving an MTP-Transfer primitive from an upper layer, or the nodal inter-working function at an SG, the M3UA layer will send a corresponding Data message (see Section 2) to its M3UA peer. The M3UA layer must fill in various fields of the common and specific headers correctly. At an SG, the M3UA address translation and mapping function determines the Application Server (AS) based on the information in the incoming message. From an ordered list of ASPs within the AS table, an Active ASP is selected and a Data message is constructed and issued on the corresponding SCTP Association. If more than one ASP is active (i.e., traffic is to be load-shared across all the active ASPs), one of the active ASPs from the list is selected. The selection algorithm is implementation dependent but could be roud-robin or based on, for example, the SLS or ISUP CIC. The appropriate selection algorithm must be chosen carefully as it is dependent on application assumptions and understanding of the degree of state coordination between the active ASPs in the AS. In addition, the message needs to be sent on the appropriate SCTP stream, again taking care to meet the message sequencing needs of the signalling application. 4.1.2 Receipt of primitives from the Layer Management On receiving these primitives from the local Layer Management, the M3UA layer will send the corresponding management message (Error) to its peer. The M3UA layer must fill in the various fields of the common and specific headers correctly. 4.2 Receipt of Peer Management messages Upon receipt of Management messages, the M3UA layer must invoke the corresponding Layer Management primitive indications (M-ERROR ind.) to the local layer management. Sidebottom et al [Page 44] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 4.3 Procedures to support the M3UA services in Section 1.4.4 These procedures support the M3UA management of SCTP Associations between SGs and ASPs. 4.3.1 State Maintenance The M3UA layer on the SG maintains the state of each AS, in each Application Server that it is configured to receive traffic, as input to the M3UA address translation and mapping function. 4.3.1.1 ASP States The state of each ASP, in each AS that it is configured, is maintained in the M3UA layer in the SG. The state of a particular ASP in a particular AS changes due to events. The events include: * Reception of messages from the peer M3UA layer at the ASP * Reception of some messages from the peer M3UA layer at other ASPs in the AS * Reception of indications from the SCTP layer * Switch-over Time triggers The ASP state transition diagram is shown in Figure 4. The possible states of an ASP are: ASP-DOWN: The remote M3UA peer at the ASP is unavailable and/or the SCTP association is down. Initially all ASPs will be in this state. ASP-UP: The remote M3UA peer at the ASP is available (and the SCTP association is up) but application traffic is stopped. ASP-ACTIVE: The remote M3UA peer at the ASP is available and application traffic is active (for a particular Routing Context or set of Routing Contexts). Sidebottom et al [Page 45] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 Figure 4: ASP State Transition Diagram +-------------+ +----------------------| | | Alternate +-------| ASP-ACTIVE |<------------+ | ASP | +-------------+ | | Takeover | ^ | | | | ASP | | ASP | | | Active | | Inactive | ASP | | | v |Takeover | | +-------------+ | | | | |-------------+ | +------>| ASP-UP |-------------+ | +-------------+ | | ^ | | ASP Down/ | ASP | | ASP Down / | ASP SCTP CDI | Up | | SCTP CDI | Down/ | | v | SCTP | +-------------+ | CDI | | | | +--------------------->| |<------------+ | ASP-DOWN | +-------------+ SCTP CDI: The local SCTP layer's Communication Down Indication to the Upper Layer Protocol (M3UA) on an SG. The local SCTP will send this indication when it detects the loss of connectivity to the ASP's peer SCTP layer. Ts: Switch-over Time Triggers. This timer is configurable by the 0perator on a per AS basis. 4.3.1.2 AS States The state of the AS is maintained in the M3UA layer on the SG. The state of an AS changes due to events. These events include: * ASP state transitions * Recovery timer triggers The possible states of an AS are: AS-DOWN: The Application Server is unavailable. This state implies that all related ASPs are in the ASP-DOWN state for this AS. Initially the AS will be in this state. AS-UP: The Application Server is available but no application traffic is active (i.e., one or more related ASPs are in the ASP-UP state, but none in the ASP-Active state). Sidebottom et al [Page 46] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 AS-ACTIVE: The Application Server is available and application traffic is active. This state implies that one ASP is in the ASP-ACTIVE state. AS-PENDING: An active ASP has transitioned from active to inactive or down and it was the last remaining active ASP in the AS. A recovery timer T(r) will be started and all incoming SCN messages will be queued by the SG. If an ASP becomes active before T(r) expires, the AS will move to AS-ACTIVE state and all the queued messages will be sent to the active ASP. If T(r) expires before an ASP becomes active, the SG stops queuing messages and discards all previously queued messages. The AS will move to AS-UP if at least one ASP is in ASP-UP state, otherwise it will move to AS-DOWN state. Figure 5: AS State Transition Diagram +----------+ one ASP trans to ACTIVE +-------------+ | |---------------------------->| | | AS-UP | | AS-ACTIVE | | |<--- --| | +----------+ \ / +-------------+ ^ | \ Tr Expiry, / ^ | | | \ at least one / | | | | \ ASP in UP / | | | | \ / | | | | \ / | | | | \ /-------/ | | one ASP | | all ASP / one ASP | | Last ACTIVE ASP trans | | trans to / \ trans to | | trans to UP or to UP | | DOWN / -------\ ACTIVE | | DOWN | | / \ | | | | / \ | | | | / \ | | | | /all ASP \ | | | v / trans to \ | v +----------+ / DOWN \ +-------------+ | |<-/ --| | | AS-DOWN | | AS-PENDING | | | | (queueing) | | |<----------------------------| | +----------+ Tr Expiry no ASP +-------------+ in UP state Tr = Recovery Timer Sidebottom et al [Page 47] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 4.3.2 ASPM procedures for primitives Before the establishment of an SCTP association the ASP state at both the SG and ASP is assumed to be "Down". As the ASP is responsible for initiating the setup of an SCTP association to an SG, the M3UA layer at an ASP receives an M-SCTP ESTABLISH request primitive from the Layer Management, the M3UA layer will try to establish an SCTP association with the remote M3UA peer at an SG. Upon reception of an eventual SCTP-Communication Up confirm primitive from the SCTP, the M3UA layer will invoke the primitive M-SCTP ESTABLISH confirm to the Layer Management. The M3UA layers at the SG will receive an SCTP-Communication_Up indication primitive from the SCTP when the association is successfully set up. The M3UA layer will then invoke the primitive M-SCTP ESTABLISH indication to the Layer Management. Once the SCTP association is established and assuming that the local M3UA-User is ready, the local ASP M3UA Application Server Process Maintenance (ASPM) function will initiate the ASPM procedures, using the ASP-Up/-Down/-Active/-Inactive messages to convey the ASP-state to the SG - see Section 4.3.3. If the M3UA layer subsequently receives an SCTP-Communication Down indication from the underlying SCTP layer, it will inform the Layer Management by invoking the M-SCTP STATUS indication primitive. The state of the remote ASP will be moved to "Down". At an ASP, the Layer Management may try to re-establish the SCTP association using M-SCTP ESTABLISH request primitive. 4.3.3 ASPM procedures for peer-to-peer messages All ASPM messages are sent on a sequenced stream to ensure ordering. SCTP stream '0' is used. 4.3.3.1 ASP-Up After an ASP has successfully established an SCTP association to an SG, the SG waits for the ASP to send an ASP-Up message, indicating that the ASP M3UA peer is available. The ASP is always the initiator of the ASP- Up exchange. When an ASP-Up message is received at an SG and internally the ASP is not considered locked-out for local management reasons, the SG marks the remote ASP as 'Up'. The SG responds with an ASP-Up Ack message in acknowledgement. The SG sends an-Up Ack message in response to a received ASP-Up message even if the ASP is already marked as "Up" at the SG. Sidebottom et al [Page 48] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 If for any local reason the SG cannot respond with an ASP-Up Ack, the SG responds to an ASP-Up with a ASP-Down message. At the ASP, the ASP-Up Ack message received from the SG is not acknowledged by the ASP. If the ASP does not receive a response from the SG, or an ASP-Down is received, the ASP may resend ASP-Up messages every 2 seconds until it receives an ASP-Up Ack message from the SG. The ASP may decide to reduce the frequency (say to every 5 seconds) if an ASP-Up Ack is not received after a few tries. The ASP must wait for the ASP-Up Ack message from the SG before sending any ASP traffic control messages (ASPAC or ASPIA) or Data messages or it will risk message loss. If the SG receives Data messages before an ASP Up is received, the SG should discard. 4.3.3.2 ASP-Down The ASP will send an ASP-Down to an SG when the ASP is to be removed from the list of ASPs in all Application Servers that it is a member. The SG marks the ASP as "Down" and returns an ASP-Down Ack message to the ASP if one of the following events occur: - an ASP-Down message is received from the ASP, - another ASPM message is received from the ASP and the SG has locked out the ASP for management reasons. The SG sends an ASP-Down Ack message in response to a received ASP-Down message from the ASP even if the ASP is already marked as "Down" at the SG. If the ASP does not receive a response from the SG, the ASP may send ASP-Down messages every 2 seconds until it receives an ASP-Down Ack message from the SG or the SCTP association goes down. The ASP may decide to reduce the frequency (say to every 5 seconds) if an ASP-Down Ack is not received after a few tries. 4.3.3.3 M3UA Version Control If an ASP-Up message with an unsupported version is received, the receiving end responds with an Error message, indicating the version the receiving node supports. This is useful when protocol version upgrades are being performed in a network. A node upgraded to a newer version should support the older versions used on other nodes it is communicating with. Because ASPs initiate the ASP-Up procedure it is assumed that the Error message would normally come from the SG. Sidebottom et al [Page 49] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 4.3.3.4 ASP-Active Anytime after the ASP has received an ASP-Up Ack from the SG, the ASP sends an ASP-Active (ASPAC) to the SG indicating that the ASP is ready to start processing traffic. In the case where an ASP is configured/registered to process the traffic for more than one Application Server across an SCTP association, the ASPAC contains one or more Routing Contexts to indicate for which Application Servers the ASPAC applies. When an ASP Active (ASPAC) message is received, the SG responds to the ASP with a ASPAC Ack message acknowledging that the ASPAC was received and starts sending traffic for the associated Application Server(s) to that ASP. There are two modes of Application Server traffic handling in the SG M3UA - Over-ride and Load-share. The Type parameter in the ASPAC message indicates the traffic handling mode used in a particular Application Server. If the SG determines that the mode indicated in an ASPAC is incompatible with the mode currently used in the AS, the SG responds with an Error message indicating "Invalid Traffic Handling Mode". In the case of an Over-ride mode AS, reception of an ASPAC message at an SG causes the redirection of all traffic for the AS to the ASP that sent the ASPAC. The SG responds to the ASPAC with an ASP-Active Ack message to the ASP. Any previously active ASP in the AS is now considered Inactive and will no longer receive traffic from the SG within the AS. The SG sends a Notify (Alternate ASP-Active) to the previously active ASP in the AS, after stopping all traffic to that ASP. In the case of a Load-share mode AS, reception of an ASPAC message at an SG causes the direction of traffic to the ASP sending the ASPAC, in addition to all the other ASPs that are currently active in the AS. The algorithm at the SG for load-sharing traffic within an AS to all the active ASPs is application and network dependent. The algorithm could, for example be round-robin or based on information in the Data message (e.g, such as the SLS, SCCP SSN, ISUP CIC value), depending on the requirements of the application and the call/transaction state handling assumptions of the collection of ASPs in the AS. The SG responds to the ASPAC with an ASP-Active Ack message to the ASP. 4.3.3.5 ASP Inactive When an ASP wishes to withdraw from receiving traffic within an AS, the ASP sends an ASP Inactive (ASPIA) to the SG. In the case where an ASP is configured/registered to process the traffic for more than one Application Server across an SCTP association, the ASPIA contains one or more Routing Contexts to indicate for which Application Servers the ASPIA applies. Sidebottom et al [Page 50] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 There are two modes of Application Server traffic handling in the SG M3UA when withdrawing an ASP from service - Over-ride and Load-share. The Type parameter in the ASPIA message indicates the mode used in a particular Application Server. If the SG determines that the mode indicates in an ASPAC is incompatible with the traffic handling mode currently used in the AS, the SG responds with an Error message indicating "Invalid Traffic Handling Mode". In the case of an Over-ride mode AS, where normally another ASP has already taken over the traffic within the AS with an Over-ride ASPAC, the ASP that sends the ASPIA is already considered by the SG to be "Inactive" (i.e., in the "Up" state). An ASPIA Ack message is sent to the ASP, after ensuring that all traffic is stopped to the ASP. In the case of a Load-share mode AS, the SG moves the ASP to the "Up" state and the AS traffic is re-allocated across the remaining "active" ASPs per the load-sharing algorithm currently used within the AS. An ASPIA Ack message is sent to the ASP after all traffic is halted to the ASP. If no other ASPs are "Active" in the Application Server, the SG either discards all incoming messages for the AS or starts buffering the incoming messages for T(r)seconds, after which messages will be discarded. T(r) is configurable by the network operator. If the SG receives an ASPAC from an ASP in the AS before expiry of T(r), the buffered traffic is directed to the ASP and the timer is cancelled. 4.3.3.6 NotifyIn the case where a Notify (AS-Up) message is sent by an SG that now has no ASPs active to service the traffic, the Notify does not force the ASP(s) receiving the message to become active. The ASPs remain in control of what (and when) action is taken. 4.3.3.7 Heartbeat The optional Heartbeat procedures may be used when operating over transport layers that do not have their own heartbeat mechanism for detecting loss of the transport association (i.e., other than the SCTP). Once the ASP sends an ASP-Up message to the SG, the ASP sends Beat messages periodically, subject to a provisionable timer T(beat). The SG M3UA, upon receiving a BEAT message from the ASP, responds with a BEAT message. If no BEAT message (or any other M3UA message), is received from the ASP within the timer 2*T(beat), the ASP will consider the remote M3UA as 'Down". At the ASP, if no BEAT message (or any other M3UA message) is received from the SG within 2*T(beat), the SG is considered unavailable. Sidebottom et al [Page 51] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 Transmission of BEAT messages is stopped and ASP-Up procedures are used to re-establish communication with the SG M3UA peer. Note: Heartbeat related events are not shown in Figure 4 "ASP state transition diagram". 4.4 Procedures to support the M3UA services in Section 1.4.3 4.4.1 At an SG On receiving an MTP-PAUSE, MTP-RESUME, or MTP-STATUS indication primitive from the nodal inter-working function at an SG, the SG M3UA layer will send a corresponding SSNM DUNA, DAVA, SCON, or DUPU message (see Section 2) to the M3UA peers at concerned ASPs. The M3UA layer must fill in various fields of the SSNM messages consistently with the information received in the primitives. The SG M3UA determines the set of concerned ASPs to be informed based on the SS7 network partition for which the primitive indication is relevant. In this way, all ASPs configured to send/receive traffic within a particular network appearance are informed. If the SG operates within a single SS7 network appearance, then all ASPs are informed. Optionally, the SG M3UA may filter further based on the Affected Point Code in the MTP-PAUSE, MTP-Resume, or MTP-Status indication primitives. In this way ASPs can be informed only of affected destinations to which they actually communicate. The SG M3UA may also suppress DUPU messages to ASPs that do not implement an MTP3-User protocol peer for the affected MTP3-User. DUNA, DAVA, SCON messages must be sent on a sequenced stream as these primitives should arrive in order. Stream 0 is used. Sequencing is not required for the DUPU or DAUD message, which may optionally be sent un- sequenced. 4.4.2 At an ASP At an ASP, upon receiving an SSNM message from the remote M3UA Peer, the M3UA layer invokes the appropriate primitive indications to the resident M3UA-Users. Local management is informed. 4.4.3 ASP Auditing An ASP may optionally initiate an audit procedure in order to enquire of an SG the availability or congestion status of an SS7 destination or set of destinations. A Destination Audit (DAUD) message is sent from the ASP to the SG requesting the current availability or congestion status of one or more SS7 Destination Point Codes. Sidebottom et al [Page 52] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 The DAUD may be sent by the ASP in the following cases. The DAUD may be sent unsequenced. - Periodic. A Timer originally set upon reception of DUVA or SCON message has expired without a subsequent DAVA, DUVA or SCON updating the availability/congestion status of the affected Destination Point Codes. The Timer is reset upon issuing a DAUD. In this case the DAUD is sent to the SG that originally sent the SSNM message. - the ASP is newly "Up" or "Active" or has been isolated from an SG for an extended period. The SG can request the availabilty/congestion status of one or more SS7 destinations to which it expects to communicate. In the first case, the DAUD procedure must not be invoked for the case of received SCON containing a congestion level value of "no congestion" or undefined" (i.e., congestion Level = "0"). This is because the value ndicates either congestion abatement or that the ITU MTP3 international ongestion method is being used. In the international congestion method, the MTP3 at the SG does not maintain the congestion status of any destinations and therefore cannot provide any congestion information in response to the DAUD. For the same reason, in the second case a DAUD cannot reveal any congested destination(s). The SG must respond to a DAUD with the MTP3 status of the routeset associated with each Destination Point Code(s) in the DAUD. The status of each SS7 destination requested is indicated in a DUNA (if unavailable), DAVA (if available/uncongested) or an SCON (if available/congested). Optionally, any DUNA or DAVA in response to a DAUD may contain more than one Affected Point Code. Note that from the point of view of an ASP sending an DAUD, the subsequent reception of an SCON implies that the Affected Destination is available. The reception of a DAVA implies that the routeset to the Affected Destination are not congested. Obviously with the reception of an DUNA, the routeset to the Affected Destination can not also be congested. Sidebottom et al [Page 53] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 5.0 Examples of M3UA Procedures 5.1 Establishment of Association and Traffic between SGs and ASPs 5.1.1 Single ASP in an Application Server ("1+0" sparing) This scenario shows the example M3UA message flows for the establishment of traffic between an SG and an ASP, where only one ASP is configured within an AS (no backup). It is assumed that the SCTP association is already set-up. SG ASP1 | |<---------ASP Up----------| |-------ASP-Up Ack-------->| | - | |<-------ASP Active--------| |-----ASP Active Ack------>| | | 5.1.2 Two ASPs in Application Server ("1+1" sparing) This scenario shows the example M3UA message flows for the establishment of traffic between an SG and two ASPs in the same Application Server, where ASP1 is configured to be "active" and ASP2 a "standby" in the event of communication failure or the withdrawal from service of ASP1. ASP2 may act as a hot, warm, or cold standby depending on the extent to which ASP1 and ASP2 share call/transaction state or can communicate call state under failure/withdrawal events. The example message flow is the same whether the ASP-Active messages are Over-ride or Load-share mode although typically this example would use an Over-ride mode. SG ASP1 ASP2 | | | |<--------ASP Up----------| | |-------ASP-Up Ack------->| | | | | |<-----------------------------ASP Up----------------| |-----------------------------ASP-Up Ack------------>| | | | | | | |<-------ASP Active-------| | |------ASP-Active Ack---->| | | | | Sidebottom et al [Page 54] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 5.1.3 Two ASPs in an Application Server ("1+1" sparing, load-sharing case) This scenario shows a similar case to Section 4.1.2 but where the two ASPs are brought to "active" and load-share the traffic load. In this case, one ASP is sufficient to handle the total traffic load. SG ASP1 ASP2 | | | |<---------ASP Up---------| | |--------ASP-Up Ack------>| | | | | |<------------------------------ASP Up---------------| |-----------------------------ASP Up Ack------------>| | | | | | | |<--ASP Active (Ldshr)----| | |-----ASP-Active Ack----->| | | | | |<----------------------------ASP Active (Ldshr)-----| |-------------------------------ASP-Active Ack------>| | | | 5.1.4 Three ASPs in an Application Server ("n+k" sparing, load-sharing case) This scenario shows the example M3UA message flows for the establishment of traffic between an SG and three ASPs in the same Application Server, where two of the ASPs are brought to "active" and share the load. In this case, a minimum of two ASPs are required to handle the total traffic load (2+1 sparing). SG ASP1 ASP2 ASP3 | | | | |<------ASP Up-------| | | |-----ASP-Up Ack---->| | | | | | | |<--------------------------ASP Up-------| | |-------------------------ASP-Up Ack)--->| | | | | | |<---------------------------------------------ASP Up--------| |---------------------------------------------ASP-Up Ack---->| | | | | | | | | |<--ASP Act (Ldshr)--| | | |----ASP-Act Ack---->| | | | | | | |<--------------------ASP Act. (Ldshr)---| | |-----------------------ASP-Act Ack----->| | | | | | Sidebottom et al [Page 55] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 5.2 ASP Traffic Fail-over Examples 5.2.1 (1+1 Sparing, withdrawal of ASP, Back-up Over-ride) Following on from the example in Section 4.1.2, and ASP withdraws from service: SG ASP1 ASP2 | | | |<-----ASP Inactive-------| | |----ASP Inactive Ack---->| | |-------------------------NTFY(AS-Down) (Optional)-->| | | | |<------------------------------ ASP Active----------| |------------------------------ASP-Active Ack)------>| | | Note: If the SG detects loss of the M3UA peer (M3UA heartbeat loss or detection of SCTP failure), the initial SG-ASP1 ASP Inactive message exchange would not occur. 5.2.2 (1+1 Sparing, Back-up Over-ride) Following on from the example in Section 4.1.2, and ASP2 wishes to over- ride ASP1 and take over the traffic: SG ASP1 ASP2 | | | |<------------------------------ ASP Active----------| |-------------------------------ASP-Active Ack------>| |----NTFY(Alt ASP-Act)--->| | | | 5.2.3 (n+k Sparing, Load-sharing case, withdrawal of ASP) Following on from the example in Section 4.1.4, and ASP1 withdraws from service: SG ASP1 ASP2 ASP3 | | | | |<----ASP Inact.-----| | | |---ASP-Inact Ack--->| | | | | | | |---------------------------------NTFY(Ins. ASPs)(Optional)->| | | | | |<-----------------------------------------ASP Act (Ldshr)---| |-------------------------------------------ASP Act (Ack)--->| | | | | Sidebottom et al [Page 56] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 The Notify message to ASP3 is optional, as well as the ASP-Active from ASP3. The optional Notify can only occur if the SG maintains knowledge of the minimum ASP resources required û for example if the SG knows that "n+k" = "2+1" for a load-share AS and "n" currently equals "1". Note: If the SG detects loss of the ASP1 M3UA peer (M3UA heartbeat loss or detection of SCTP failure), the first SG-ASP1 ASP Inactive message exchange would not occur. 5.3 M3UA/MTP3-User Boundary Examples 5.3.1 At an ASP This section describes the primitive mapping from the MTP3 User to M3UA at an ASP. 5.3.1.1 Support for MTP-Transfer on the ASP 5.3.1.1.1 Support for MTP-Transfer Request When the MTP3-User on the ASP has data to send into the SS7 network, it will use the MTP-Transfer Request primitive. The M3UA on the ASP will do the following when it receives an MTP-Transfer Request primitive from the M3UA user: - Determine the correct SG - Determine the correct association to the chosen SG - Determine the correct stream in the association (e.g., based on SLS) - Determine whether to complete the optional fields of the Data message - Map the MTP-Transfer Request primitive into the Protocol Data field of an m3ua Data message - Send the Data message to the remote M3UA peer in the SG, over the SCTP association SG ASP | | |<-----Data Message-------|<--MTP-Transfer req. | | Sidebottom et al [Page 57] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 5.3.1.1.2 Support for MTP Transfer Indication When the M3UA on the ASP has received Data messages from the remote M3UA peer in the SG it will do the following: - Evaluate the optional fields of the Data message if present - Map the Payload of a Data message into the MTP-Transfer Indication primitive - Pass the MTP-Transfer Indication primitive to the user part. In case of multiple user parts, the optional fields of the Data message are used to determine the concerned user part. SG ASP | | |------Data Message------>|---MTP-Transfer ind. | | 5.3.1.1.3 Support for ASP Querying of SS7 Destination States There are situations such as temporary loss of connectivity to the SG that may cause the M3UA on the ASP to audit SS7 destination availability states. Note: there is no primitive for the MTP3-User to request this audit from the M3UA as this is initiated by an internal M3UA management function. The M3UA on the ASP normally sends Destination State Audit (DAUD) messages for each of the destinations that the ASP supports. SG ASP | | |<-----DAUD Message ------| |<-----DAUD Message ------| |<-----DAUD Message ------| | | | | 5.3.2 At an SG This section describes the MTP3 upper layer primitive mapping to the M3UA at the SG. 5.3.2.1 Support for MTP-Transfer Request at the SG When the M3UA on the SG has received Data messages from its peer destined to the SS7 network it will do the following: Sidebottom et al [Page 58] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 - Evaluate the optional fields of the Data message if present to determine the network appearance - Map the Protocol data of the Data message into an MTP-Transfer Request primitive - Pass the MTP-Transfer Request primitive to the MTP3 of the concerned network appearance. SG ASP | | <---MTP-Transfer req.|<------Data Message------| | | 5.3.2.2 Support for MTP-Transfer Indication at the SG When the MTP3 on the SG has data to pass its user parts, it will use the MTP-Transfer Indication primitive. The M3UA on the S>G will do the following when it receives an MTP-Transfer Indication: - Determine the correct ASP - Determine the correct association to the chosen ASP - Determine the correct stream in the association (e.g., based on SLS) - Determine whether to complete the optional fields of the Data message - Map the MTP-Transfer Indication primitive into the Protocol Data field of an M3UA Data message - Send the Data message to the remote M3UA peer in the ASP, over the SCTP association SG ASP | | --MTP-Transfer ind.->|------Data Message------>| | | 5.3.2.3 Support for MTP-PAUSE, MTP-RESUME, MTP-STATUS The MTP-PAUSE, MTP-RESUME and MTP-STATUS indication primitives from the MTP3 upper layer interface at the SG need to be made available to the remote MTP3 User Part lower layer interface at the concerned ASP(s). Sidebottom et al [Page 59] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 5.3.2.3.1 Destination Unavailable The MTP3 on the SG will generate an MTP-PAUSE primitive when it determines locally that an SS7 destination is unreachable. The M3UA will map this primitive to a Destination Unavailable (DUNA) message. It will determine which ASP(s) to send the DUNA based on the Network Appearance information. SG ASP | | --MTP-PAUSE ind.-->|------DUNA Message ----->|--MTP-PAUSE ind.--> | | 5.3.2.3.2 Destination Available The MTP3 on the SG will generate an MTP-RESUME primitive when it determines locally that an SS7 destination that was previously unreachable is now reachable. The M3UA will map this primitive to a Destination Unavailable (DAVA) message. It will determine which ASP(s) to send the DUNA based on the Network Appearance information. SG ASP | | --MTP-RESUME ind.-->|------DAVA Message ----->|--MTP-RESUME ind.--> | | 5.3.2.3.3 SS7 Network Congestion The MTP3 on the SG will generate an MTP-STATUS primitive when it determines locally that the route to an SS7 destination is congested. The M3UA will map this primitive to a SS7 Network Congestion State (SCON) message. It will determine which ASP(s) to send the DUPU to based on the intended Application Server. SG ASP | | --MTP-STATUS ind.-->|------SCON Message ----->|--MTP-STATUS ind.--> | | Sidebottom et al [Page 60] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 5.3.2.3.4 Destination User Part Unavailable The MTP3 on the SG will generate an MTP-STATUS primitive when it determines locally that an SS7 destination User Part is unavailable. The M3UA will map this primitive to a Destination User Part Unavailable (DUPU) message. It will determine which ASP(s) to send the DUPU based on the intended Application Server. SG ASP | | --MTP-STATUS ind.-->|------DUPU Message ----->|--MTP-STATUS ind.--> | | 6.0 Security 6.1 Introduction M3UA is designed to carry signalling messages for telephony services. As such, M3UA must involve the security needs of several parties: the end users of the services; the network providers and the applications involved. Additional requirements may come from local regulation. While having some overlapping security needs, any security solution should fulfill all of the different parties' needs. 6.2 Threats There is no quick fix, one-size-fits-all solution for security. As a transport protocol, M3UA has the following security objectives: * Availability of reliable and timely user data transport. * Integrity of user data transport. * Confidentiality of user data. M3UA runs on top of SCTP. SCTP [6] provides certain transport related security features, such as some protection against: * Blind Denial of Service Attacks * Flooding * Masquerade * Improper Monopolization of Services When M3UA is running in professionally managed corporate or service provider network, it is reasonable to expect that this network includes an appropriate security policy framework. The "Site Security Handbook" [21] should be consulted for guidance. When the network in which M3UA runs in involves more than one party, it may not be reasonable to expect that all parties have implemented security in a sufficient manner. In such a case, it is recommended that Sidebottom et al [Page 61] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 IPSEC is used to ensure confidentiality of user payload. Consult [22] for more information on configuring IPSEC services. 6.3 Protecting Confidentiality Particularly for mobile users, the requirement for confidentiality may include the masking of IP addresses and ports. In this case application level encryption is not sufficient; IPSEC ESP should be used instead. Regardless of which level performs the encryption, the IPSEC ISAKMP service should be used for key management. 7.0 IANA Considerations A request will be made to IANA to assign an M3UA value for the Payload Protocol Identifier in SCTP Payload Data chunk. The following SCTP Payload Protocol Identifier will be registered: M3UA tbd The SCTP Payload Protocol Identifier is included in each SCTP Data chunk, to indicate which protocol the SCTP is carrying. This Payload Protocol Identifier is not directly used by SCTP but may be used by certain network entities to identify the type of information being carried in a Data chunk. The User Adaptation peer may use the Payload Protocol Identifier as a way of determining additional information about the data being presented to it by SCTP. 8.0 Acknowledgements The authors would like to thank John Loughney, Neil Olson, Michael Tuexen, Nikhil Jain, Steve Lorusso, Dan Brendes, Heinz Prantner, Barry Nagelberg for their valuable comments and suggestions. 9.0 References [1] RFC 2719, "Framework Architecture for Signaling Transport" [2] ITU-T Recommendations Q.761 to Q.767, 'Signalling System No.7 (SS7) û ISDN User Part (ISUP)' [3] ANSI T1.113 - 'Signaling System Number 7 û ISDN User Part [4] ETSI ETS 300 356-1 "Integrated Services Digital Network (ISDN); Signalling System No.7; ISDN User Part (ISUP) version 2 for the international interface; Part 1: Basic services" Sidebottom et al [Page 62] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 [5] ITU-T Recommendations Q.711-715, 'Signalling System No. 7 (SS7) - Signalling Connection Control Part (SCCP)' [6] ANSI T1.112 'Signaling System Number 7 û Signaling Connection Control Part' [7] ETSI ETS 300 009-1, "Integrated Services Digital Network (ISDN); Signalling System No.7; Signalling Connection Control Part (SCCP) (connectionless and connection-oriented class 2) to support international interconnection; Part 1: Protocol specification" [8] ITU-T Recommendations Q.720, 'Telephone User Part' [9] ITU-T Recommendation Q.771-775 'Signalling System No. 7 SS7) - Transaction Capabilities (TCAP) [10] ANSI T1.114 'Signaling System Number 7 û Transaction Capabilities Application Part' [11] ETSI ETS 300 287-1, "Integrated Services Digital Network (ISDN); Signalling System No.7; Transaction Capabilities (TC) version 2; Part 1: Protocol specification" [12] 3G TS 25.410 V3.1.0 (2000-01) Technical Specification û 3rd Generation partnership Project; Technical Specification Group Radio Access Network; UTRAN Iu Interface: General Aspects and Principles (3G TS 25.410 Version 3.1.0 Release 1999) [13] Stream Control Transport Protocol , July 2000, Work in Progress [14] ITU-T Recommendations Q.701-Q.705, 'Signalling System No. 7 (SS7) - Message Transfer Part (MTP)' [15] ANSI T1.111 'Signaling System Number 7 - Message Transfer Part' [16] ETSI ETS 300 008-1, "Integrated Services Digital Network (ISDN); Signalling System No.7; Message Transfer Part (MTP) to support international interconnection; Part 1: Protocol specification" [17] ITU-T Recommendation Q.2140 'B-ISDN ATM Adaptation Layer - Service Specific Coordination Function for signalling at the Network Node Interface (SSCF at NNI) [18] ITU-T Recommendation Q.2110 'B-ISDN ATM Adaptation Layer - Service Specific Connection Oriented Protocol (SSCOP) [19] MTP2-User Adaptation Layer , Nov. 1999, Work in Progress Sidebottom et al [Page 63] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 [20] ITU-T Recommendation Q.2210 'B-ISDN MTP' [21] RFC 2196, "Site Security Handbook", B. Fraser Ed., September 1997 [22] RFC 2401, "Security Architecture for the Internet Protocol", S. Kent, R. Atkinson, November 1998. 10.0 Author's Addresses Lyndon Ong Nortel Networks 4401 Great America Pkwy Santa Clara, CA, USA 95054 long@nortelnetworks.com Greg Sidebottom Nortel Networks 3685 Richmond Rd, Nepean, Ontario, Canada K2H 5B7 gregside@nortelnetworks.com Guy Mousseau Nortel Networks 3685 Richmond Rd Nepean, Ontario, Canada K2H 5B7 Ian Rytina Ericsson Australia 37/360 Elizabeth Street Melbourne, Victoria 3000, Australia ian.rytina@ericsson.com Hanns Juergen Schwarzbauer SIEMENS AG Hofmannstr. 51 81359 Munich, Germany HannsJuergen.Schwarzbauer@icn.siemens.de Ken Morneault Cisco Systems Inc. 13615 Dulles Technology Drive Herndon, VA, USA 20171 EMail: kmorneau@cisco.com Sidebottom et al [Page 64] Internet Draft SS7 MTP3-User Adaptation Layer June 2000 Malleswar Kalla Telcordia Technologies MCC 1J211R 445 South Street Morristown, NJ, USA 07960 EMail: kalla@research.telcordia.com Normand Glaude Performance Technologies 150 Metcalf Sreet, Suite 1300 Ottawa, Ontario, Canada K2P 1P1 EMail: nglaude@microlegend.com This draft expires December 2000.