TOC 
SippingS. Okumura
Internet-DraftSoftfront
Intended status: InformationalP. Kyzivat
Expires: November 11, 2010Cisco Systems, Inc.
 May 10, 2010


SIP (Session Initiation Protocol) Usage of the Offer/Answer Model
draft-ietf-sipping-sip-offeranswer-13

Abstract

The Session Initiation Protocol (SIP) utilizes the offer/answer model to establish and update multimedia sessions using the Session Description Protocol (SDP). The description of the offer/answer model in SIP is dispersed across multiple RFCs. This document summarizes all the current usages of the offer/answer model in SIP communication.

Status of this Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as “work in progress.”

This Internet-Draft will expire on November 11, 2010.

Copyright Notice

Copyright (c) 2010 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.



Table of Contents

1.  Introduction
    1.1.  Terminology
2.  Summary of SIP usage of the Offer/Answer Model
    2.1.  Offer/Answer Exchange Pairs in SIP Messages
    2.2.  Rejection of an Offer
    2.3.  Session Description which is not Offer nor Answer
3.  Detailed Discussion of the Offer/Answer Model for SIP
    3.1.  Offer/Answer for the INVITE method with 100rel extension
        3.1.1.  INVITE Request with SDP
        3.1.2.  INVITE request without SDP
    3.2.  Offer/Answer Exchange in Early Dialog
    3.3.  Offer/Answer Exchange in an Established Dialog
    3.4.  Recovering From a Failed ReINVITE
4.  Exceptional Case Handling
    4.1.  Message Crossing Case Handling
    4.2.  Glare Case Handling
    4.3.  Interworking of UPDATE and reINVITE
5.  Content of Offers and Answers
    5.1.  General Principle for Constructing Offers and Answers
    5.2.  Choice of Media Types and Formats to Include and Exclude
        5.2.1.  Sending an Initial INVITE with Offer
        5.2.2.  Responding with an Offer when the Initial INVITE has no Offer
        5.2.3.  Answering an Initial INVITE with Offer
        5.2.4.  Answering when the Initial INVITE had no Offer
        5.2.5.  Subsequent Offers and Answers
    5.3.  Hold and Resume of media
    5.4.  Behavior on receiving SDP with c=0.0.0.0
6.  IANA Considerations
7.  Security Considerations
8.  Acknowledgement
9.  References
    9.1.  Normative References
    9.2.  Informative References
§  Authors' Addresses




 TOC 

1.  Introduction

SIP utilizes the offer/answer model to establish and update sessions. The rules to govern the offer/answer behaviors in SIP are described in the several RFCs. ([RFC3261] (Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, “SIP: Session Initiation Protocol,” June 2002.), [RFC3262] (Rosenberg, J. and H. Schulzrinne, “Reliability of Provisional Responses in Session Initiation Protocol (SIP),” June 2002.), [RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.), [RFC3311] (Rosenberg, J., “The Session Initiation Protocol (SIP) UPDATE Method,” October 2002.), and [I‑D.camarillo‑sipcore‑reinvite] (Camarillo, G., Holmberg, C., and G. yang, “Re-INVITE and Target-refresh Request Handling in the Session Initiation Protocol (SIP),” October 2009.).)

The primary purpose of this document is to describe all forms of SIP usage of the offer/answer model in one document to help the readers to fully understand it. Also, this document tries to incorporate the results of the discussions on the controversial issues to avoid repeating the same discussions later.

This document does not make normative changes. Rather, it recommends how to use the existing standards to best effect.



 TOC 

1.1.  Terminology

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119] (Bradner, S., “Key words for use in RFCs to Indicate Requirement Levels,” March 1997.). This document only uses these key words when referencing normative statements in existing RFCs.



 TOC 

2.  Summary of SIP usage of the Offer/Answer Model

The offer/answer model itself is independent from the higher layer application protocols which utilize it. SIP is one of the applications using the offer/answer model. [RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.) defines the offer/answer model, but does not specify which SIP messages should convey an offer or an answer. This should be defined in the SIP core and extensions RFCs.

In theory, any SIP message can include a session description in its body. But a session description in a SIP message is not necessarily an offer or an answer. Only certain session description usages that conform to the rules described in standards-track RFCs can be interpreted as an offer or an answer. The rules for how to handle the offer/answer model are defined in several RFCs.

The offer/answer model defines a mechanism for update of sessions. In SIP, a dialog is used to associate an offer/answer exchange with the session which it is to update. In other words, only the offer/answer exchange in the SIP dialog can update the session which is managed by that dialog.



 TOC 

2.1.  Offer/Answer Exchange Pairs in SIP Messages

Currently, the rules on the offer/answer model are defined in [RFC3261] (Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, “SIP: Session Initiation Protocol,” June 2002.), [RFC3262] (Rosenberg, J. and H. Schulzrinne, “Reliability of Provisional Responses in Session Initiation Protocol (SIP),” June 2002.), [RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.), [RFC3311] (Rosenberg, J., “The Session Initiation Protocol (SIP) UPDATE Method,” October 2002.) and [I‑D.camarillo‑sipcore‑reinvite] (Camarillo, G., Holmberg, C., and G. yang, “Re-INVITE and Target-refresh Request Handling in the Session Initiation Protocol (SIP),” October 2009.). In these RFCs, only the six patterns shown in Table 1 are defined for exchanging an offer and an answer with SIP messages.

Note that an offer/answer exchange initiated by an INVITE request must follow exactly one of the patterns 1, 2, 3, 4. When an initial INVITE causes multiple dialogs due to forking, an offer/answer exchange is carried out independently in each distinct dialog. When an INVITE request contains no offer, only Pattern 2 or Pattern 4 apply. 'The first reliable non-failure message' must have an offer if there is no offer in the INVITE request. This means that UA which receives the INVITE request without an offer must include an offer in the first reliable response with 100rel extension. If no reliable provisional response has been sent, the UAS must include an offer when sending 2xx response.

In Pattern 3, the first reliable provisional response may or may not have an answer. When a reliable provisional response contains a session description, and is the first to do so, then that session description is the answer to the offer in the INVITE request. The answer can not be updated, and a new offer can not be sent in a subsequent reliable response for the same INVITE transaction.

In Pattern 5, a PRACK request can contain an offer only if the reliable response which it acknowledges contains an answer to the previous offer/answer exchange.

NOTE: It is legal to have UPDATE/2xx exchanges without offer/answer exchanges (Pattern 6). However when re-INVITEs are sent for non-offer/answer purposes, an offer/answer exchange is required. In that case the prior SDP will typically be repeated.

There may be ONLY ONE offer/answer negotiation in progress for a single dialog at any point in time. Section 4 (Exceptional Case Handling) explains how to ensure this. When an INVITE results in multiple dialogs each has a separate offer/answer negotiation.

NOTE: This is when using a Content-Disposition of "session". There may be a second offer/answer negotiation in progress using a Content-Disposition of "early-session" [RFC3959] (Camarillo, G., “The Early Session Disposition Type for the Session Initiation Protocol (SIP),” December 2004.). That is not addressed by this draft.



         Offer                Answer             RFC    Ini Est Early
  -------------------------------------------------------------------
  1. INVITE Req.          2xx INVITE Resp.     RFC 3261  Y   Y    N
  2. 2xx INVITE Resp.     ACK Req.             RFC 3261  Y   Y    N
  3. INVITE Req.          1xx-rel INVITE Resp. RFC 3262  Y   Y    N
  4. 1xx-rel INVITE Resp. PRACK Req.           RFC 3262  Y   Y    N
  5. PRACK Req.           200 PRACK Resp.      RFC 3262  N   Y    Y
  6. UPDATE Req.          2xx UPDATE Resp.     RFC 3311  N   Y    Y
 Table 1: Summary of SIP Usage of the Offer/Answer Model 

In Table 1, '1xx-rel' corresponds to the reliable provisional response which contains the 100rel option defined in [RFC3262] (Rosenberg, J. and H. Schulzrinne, “Reliability of Provisional Responses in Session Initiation Protocol (SIP),” June 2002.).

The 'Ini' column shows the ability to exchange the offer/answer to initiate the session. 'Y' indicates that the pattern can be used in the initial offer/answer exchange, while 'N' indicates that it can not. Only the initial INVITE transaction can be used to exchange the offer/answer to establish a multimedia session.

The 'Est' column shows the ability to update the established session.

The 'Early' column indicates which patterns may be used to modify the established session in an early dialog. There are two ways to exchange a subsequent offer/answer in an early dialog.



 TOC 

2.2.  Rejection of an Offer

It is not always clear how to reject an offer when it is unacceptable, and some methods do not allow explicit rejection of an offer. For each of the patterns in Table 1, Table 2 shows how to reject an offer.

When a UA receives an INVITE request with an unacceptable offer, it should respond with a 488 response, preferably with Warning header field indicating the reason of the rejection, unless another response code is more appropriate to reject it. (Pattern 1 and Pattern 3.)

If this is a reINVITE extra care must be taken, as detailed in [I‑D.camarillo‑sipcore‑reinvite] (Camarillo, G., Holmberg, C., and G. yang, “Re-INVITE and Target-refresh Request Handling in the Session Initiation Protocol (SIP),” October 2009.). Specifically, if the offer contains any changes or additions to media stream properties, and those have already been used to transmit/receive media before the final response is sent, then a 2xx response should be sent, with a syntactically correct session description. This may optionally be followed by an UPDATE request to rearrange the session parameters if both ends support the UPDATE method. Alternatively the UA may send an error response to the (re)INVITE request to terminate the dialog or to roll back the offer-answer status before sending reINVITE request. In this case UAS should not continue to retransmit the unacknowledged reliable provisional response, UAC should not continue to retransmit a PRACK request.

When a UA receives an UPDATE request with an offer which it can not accept, it should respond with a 488 response preferably with Warning header field indicating the reason of the rejection, unless another response code is more appropriate to reject it. (Pattern 6)

When a UA receives a PRACK request with an offer which it can not accept, it may respond with a 200 response with a syntactically correct session description. This may optionally be followed by an UPDATE request to rearrange the session parameters if both ends support the UPDATE method. Alternatively the UA may terminate the dialog and send an error response to the INVITE request. (Pattern 5) The 488 response is another proposed solution, UAS may respond with a 488 response and then UAC should send again a PRACK request without an offer.

NOTE: In [RFC3262] (Rosenberg, J. and H. Schulzrinne, “Reliability of Provisional Responses in Session Initiation Protocol (SIP),” June 2002.), the following restriction is defined with regard to responding to a PRACK request.

"If the PRACK does match an unacknowledged reliable provisional response, it MUST be responded to with a 2xx response."

This description is not completely correct. There are cases where it is unacceptable to send a 2xx response. For example, 401 response can not be avoided.

When a UA receives a response with an offer which it can not accept, the UA does not have a way to reject it explicitly. Therefore, a UA should respond to the offer with the correct session description and rearrange the session parameters by initiating a new offer/answer exchange, or alternatively terminate the session. (Pattern 2 and Pattern 4) When initiating a new offer/answer, a UA should take care not to cause an infinite offer/answer loop.



     Offer                Rejection
  ------------------------------------------------------------------
  1. INVITE Req. (*)      488 INVITE Response
  2. 2xx INVITE Resp.     Answer in ACK Req. followed by new offer
                          OR termination of dialog
  3. INVITE Req.          488 INVITE Response (same as Pattern 1.)
  4. 1xx-rel INVITE Resp. Answer in PRACK Req. followed by new offer
  5. PRACK Req. (**)      200 PRACK Resp. followed by new offer
                          OR termination of dialog
  6. UPDATE Req.          488 UPDATE Response

(*) If this was a reINVITE, a failure response should not be sent if media has already been exchanged using the new offer.

(**) A UA should only use PRACK to send an offer when it has strong reasons to expect the receiver will accept the offer.

 Table 2: Rejection of an Offer 



 TOC 

2.3.  Session Description which is not Offer nor Answer

As previously stated, a session description in a SIP message is not necessarily an offer or an answer. For example, SIP can use a session description to describe capabilities apart from offer/answer exchange. Examples of this are 200 OK responses for OPTIONS and 488 responses for INVITE.



 TOC 

3.  Detailed Discussion of the Offer/Answer Model for SIP



 TOC 

3.1.  Offer/Answer for the INVITE method with 100rel extension

The INVITE method provides the basic procedure for offer/answer exchange in SIP. Without the 100rel option, the rules are simple as described in [RFC3261] (Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, “SIP: Session Initiation Protocol,” June 2002.). If an INVITE request includes a session description, Pattern 1 is applied and if an INVITE request does not include a session description, Pattern 2 is applied.

With 100rel, Pattern 3, 4 and 5 are added and this complicates the rules. An INVITE request may cause multiple responses. Note that even if both UAs support the 100rel extension, not all the provisional responses may be sent reliably.



 TOC 

3.1.1.  INVITE Request with SDP

When a UAC includes an SDP body in the INVITE request as an offer, only the first SDP in a reliable non-failure response to the INVITE request is the real answer. No other offer/answer exchanges can occur within the messages (other responses and ACK) of the INVITE transaction.

In [RFC3261] (Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, “SIP: Session Initiation Protocol,” June 2002.) there are some descriptions about an offer/answer exchange, but those cause a little confusion. We interpret those descriptions as follows,

UAC behavior

  1. If the first SDP that UAC received is included in an unreliable provisional response to the INVITE request, UAC MUST treat it as an answer. But the SDP is not a real answer, therefore the offer/answer exchange is not yet completed.
  2. After UAC has received the answer in a reliable provisional response to the INVITE, any SDP in subsequent responses to the INVITE MUST be ignored.
  3. If the second and subsequent SDP(including a real answer) is different from the first SDP, UAC should consider that the SDP is equal to the first SDP. Therefore, UAC should not switch to the new SDP.

UAS behavior

  1. All SDP in the responses to the INVITE request MUST be the same exactly.
  2. After UAS has sent the answer in a reliable provisional response to the INVITE, UAS should not include any SDP in subsequent responses to the INVITE.
  3. UAS MAY send any provisional response without a SDP regardless of the transmission of the answer.

A session description in an unreliable response that precedes a reliable response can be considered a "preview" of the answer that will be coming.

NOTE: This "preview" session description rule applies to a single offer/answer exchange. In parallel offer/answer exchanges (caused by forking) a UA may obviously receive a different "preview" of an answer in each dialog. UAs are expected to deal with this.

Although [RFC3261] (Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, “SIP: Session Initiation Protocol,” June 2002.) says a UA should accept media once an INVITE with an offer has been sent, in many cases, an answer (or, at least a preview of it) is required in order for media to be accepted. Two examples of why this might be required are:

Therefore, a UAS should send a SDP answer reliably (if possible) before it starts sending media. And, if neither the UAC nor the UAS support 100rel, the UAS should send a preview of the answer before it starts sending media.



   UAC                   UAS
    | F1  INVITE (SDP)    | <- The offer in the offer/answer model
    |-------------------->|
    | F2     1xx (SDP)    | <- The offer/answer exchange is not
    |<--------------------|    closed yet, but UAC acts as if it
    |                     | ^  receives the answer.
    | F3 1xx-rel (no SDP) | |<- a 1xx-rel may be sent without answer
    |<--------------------| |   SDP.
    | F4   PRACK (no SDP) | |
    |-------------------->| | UAC must not send a new offer.
    | F5 2xx PRA (no SDP) | |
    |<--------------------| v
    |                     |
    | F6 1xx-rel (SDP)    | <- The answer in the offer/ answer model
    |<--------------------| -
    | F7   PRACK          | | UAC can send a new offer in a PRACK
    |-------------------->| | request to acknowledge F6.
    | F8 2xx PRA          | | After F7 UAC and UAS can send a new
    |<--------------------| v offer in an UPDATE request.
    |                     |
    | F9 1xx-rel          | <- SDP should not be included in the
    |<--------------------|    subsequent 1xx-rel once offer/answer
    | F10  PRACK          |    has been completed.
    |-------------------->|
    | F11 2xx PRA         |
    |<--------------------|
    |                     |
    | F12 2xx INV         | <- SDP should not be included in the
    |<--------------------|    final response once offer/answer has
    | F13    ACK          |    been completed.
    |-------------------->|
 Figure 1: Example of Offer/Answer with 100rel Extension (1) 

For example, in Figure 1 (Example of Offer/Answer with 100rel Extension (1)), only the SDP in F6 is the answer. The SDP in the non-reliable response (F2) is the preview of the answer and must be the same as the answer in F6. Receiving F2, the UAC should act as if it receives the answer. However, offer/answer exchange is not completed yet and the UAC must not send a new offer until it receives the same SDP in a reliable non-failure response, which is the real answer. After sending the SDP in F6, the UAS must prepare to receive a new offer from the UAC in a PRACK request, or in an UPDATE request if the UAS supports UPDATE.

The UAS does not include SDP in responses F9 and F12. However, the UAC should prepare to receive SDP bodies in F9 and/or F12, and just ignore them, to handle a peer that does not conform to the recommended implementation.



 TOC 

3.1.2.  INVITE request without SDP

When a UAC does not include a SDP body in the INVITE request, it expects an offer to be received with the first reliable non-failure response. And a UAS MUST include an offer in the first reliable non-failure response and should not include any SDP in the other responses to the INVITE request. The UAC will send the answer in the request to acknowledge the response, i.e. PRACK or ACK request of the reliable response. Other than that, no offer/answer exchanges can occur in the messages within the INVITE transaction.

NOTE: The UAS should not include SDP in the responses F6 and F9. However, the UAC should prepare to receive SDP bodies in F6 and/or F9, and just ignore them to handle a peer that does not conform to the recommended implementation.



   UAC                   UAS
    | F1  INVITE (no SDP) |
    |-------------------->|
    | F2     1xx          |
    |<--------------------|
    |                     |
    | F3 1xx-rel (SDP)    | <- The first 1xx-rel must contain SDP
    |<--------------------|    as the offer.
    | F4   PRACK (SDP)    | <- A PRACK request to the first 1xx-rel
    |-------------------->|    must contain SDP as the answer.
    | F5 2xx PRA (no SDP) | -
    |<--------------------| |
    |                     | |
    | F6 1xx-rel (no SDP) | <- The subsequent 1xx-rel should not
    |<--------------------| |  contain SDP.
    | F7   PRACK          | |
    |-------------------->| | UAC can send a new offer in an UPDATE
    | F8 2xx PRA          | | request after F4.
    |<--------------------| v
    |                     |
    | F9 2xx INV (no SDP) | <- The final response should not
    |<--------------------|    contain SDP.
    | F10    ACK          |
    |-------------------->|
 Figure 2: Example of Offer/Answer with 100rel Extension (2) 

Note that in the case that the UAC needs to prompt the user to accept or reject the offer, the reliable provisional response with SDP as an offer (Pattern 4) can result in the retransmission until the PRACK request can be sent. The UAC should take care to avoid this situation when it sends the INVITE request without SDP.



 TOC 

3.2.  Offer/Answer Exchange in Early Dialog

When both UAs support the 100rel extension, they can update the session in the early dialog once the first offer/answer exchange has been completed.

From a UA sending an INVITE request:

A UA can send an UPDATE request with a new offer if both ends support the UPDATE method. Note that if the UAS needs to prompt the user to accept or reject the offer, the delay can result in retransmission of the UPDATE request.

A UA can send a PRACK request with a new offer only when acknowledging the reliable provisional response carrying the answer to an offer in the INVITE request. Compared to using the UPDATE method, using PRACK can reduce the number of messages exchanged between the UAs. However, to avoid problems or delays caused by PRACK offer rejection, the UA is recommended to send a PRACK request only when it has strong reasons to expect the receiver will accept it. For example, the procedure used in precondition extension [RFC3312] (Camarillo, G., Marshall, W., and J. Rosenberg, “Integration of Resource Management and Session Initiation Protocol (SIP),” October 2002.) is a case where a PRACK request should be used for updating the session status in an early dialog. Note also that if a UAS needs to prompt the user to accept or reject the offer, the delay can result in retransmission of the PRACK request.

From a UA receiving an INVITE request:

A UA can send an UPDATE request with a new offer if both ends support the UPDATE method. A UAS can not send a new offer in the reliable provisional response, so the UPDATE method is the only method for a UAS to update an early session.



 TOC 

3.3.  Offer/Answer Exchange in an Established Dialog

Both the re-INVITE and UPDATE methods can be used in an established dialog to update the session.

The UPDATE method is simpler and can save at least one message compared with the INVITE method. But both ends must support the UPDATE method for it to be used.

The INVITE method needs at least three messages to complete but no extensions are needed. Additionally, the INVITE method allows the peer to take time to decide whether it will accept a session update or not by sending provisional responses. That is, re-INVITE allows the UAS to interact with the user at the peer, while UPDATE needs to be answered automatically by the UAS. It is noted that re-INVITE should be answered immediately unless such a user interaction is needed. Otherwise, some 3pcc flows will break.



 TOC 

3.4.  Recovering From a Failed ReINVITE

If a reINVITE fails, the session parameters in effect prior to the reINVITE MUST remain unchanged, as if no re-INVITE had been issued. ([RFC3261] (Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, “SIP: Session Initiation Protocol,” June 2002.) section 14.1.) This remains the case even if multiple offer/answer exchanges have occurred between the sending of the reINVITE and its failure, and even if media has been exchanged using the proposed changes in the session. Because this can be difficult to achieve in practice, newer specifications call for the UAS to send a 2xx response to a reINVITE in cases where rolling back changes would be problematic.

Nevertheless, a UAC may receive a failure response to a reINVITE after proposed changes that must be rolled back have already been used. In such a case, the UAC should send an UPDATE offering the SDP that has been reinstated. (See [I‑D.camarillo‑sipcore‑reinvite] (Camarillo, G., Holmberg, C., and G. yang, “Re-INVITE and Target-refresh Request Handling in the Session Initiation Protocol (SIP),” October 2009.) for details.)



 TOC 

4.  Exceptional Case Handling

In [RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.), the following restrictions are defined with regard to sending a new offer.

"At any time, either agent MAY generate a new offer that updates the session. However, it MUST NOT generate a new offer if it has received an offer which it has not yet answered or rejected. It MUST NOT generate a new offer if it has generated a prior offer for which it has not yet received an answer or a rejection."

Assuming that the above rules are guaranteed, there seem to be two possible 'exceptional' cases to be considered in SIP offer/answer usage: the 'message crossing' case, and the 'glare' case. One of the reasons why the usage of SIP methods to exchange offer/answer needs to be carefully restricted in the RFCs is to ensure that the UA can detect and handle appropriately the 'exceptional' cases to avoid incompatible behavior.



 TOC 

4.1.  Message Crossing Case Handling

When message packets cross in the transport network, an offer may be received before the answer for the previous offer/answer exchange, as shown in Figure 3 (Message Crossing Case). In such a case, UA A must detect that the session description SDP-2 is not the answer to offer1.




      A                  B
      |SDP-1     (offer1)|
   M1 |----------------->|
      |SDP-2    (answer1)|
   M2 |<------\  /-------|
      |        \/        |
      |SDP-3   /\(offer2)|
   M3 |<------/  \-------|
 Figure 3: Message Crossing Case 

Because of the restrictions on placement of offers and answers (summarized in Table 1) there are a limited number of valid exchanges of messages that may lead to this message crossing case. These are enumerated in Table 3. (This table only shows messages containing offers or answers. There could be other messages, without session descriptions, which are not shown.)

When a response to UPDATE request crosses a reliable response to INVITE request, there are variants shown in Figures 4 (Avoidable message crossing cases) and 5 (Avoidable message crossing cases), which are dependent on an INVITE (Mx) that contains no offer. These are also included in Table 3.



                A                               B
                |                               |
                |SDP-1               offer1(UPD)|
             M1 |==============================>|
                |re-INV               (no offer)|
             Mx |------------------------------>| --+
                |SDP-2         answer1 (2xx-UPD)|   |
             M2 |<===========\  /===============|   | first reliable
                |             \/          offer2|   | response
                |SDP-3        /\   (1xx-rel/2xx)|   |
             M3 |<===========/  \===============| <-+
                |SDP-4       answer2 (PRACK/ACK)|
             My |------------------------------>|
                |                               |
 Figure 4: Avoidable message crossing cases 

To avoid this message crossing condition shown in Figure 4 (Avoidable message crossing cases), UA A should not send this reINVITE request at this point. If UA B encounters this message crossing condition, it should reject this reINVITE request with a 500 response.



                A                               B
                |                               |
                |re-INV               (no offer)|
             Mx |------------------------------>| --+
                |SDP-1               offer1(UPD)|   |
             M1 |==============================>|   |
                |SDP-2         answer1 (2xx-UPD)|   |
             M2 |<===========\  /===============|   | first reliable
                |             \/          offer2|   | response
                |SDP-3        /\   (1xx-rel/2xx)|   |
             M3 |<===========/  \===============| <-+
                |SDP-4       answer2 (PRACK/ACK)|
             My |------------------------------>|
                |                               |
 Figure 5: Avoidable message crossing cases 

To avoid this message crossing condition shown in Figure 5 (Avoidable message crossing cases), UA A should not send this UPDATE request at this point. If UA B encounters this message crossing condition, it should reject this UPDATE request with a 500 response.

The situation when PRACK request crosses UPDATE request is shown in Figure 6 (Avoidable message crossing cases).



                A                               B
                |                               |
                |              re-INV (no offer)|
1st reliable+-- |<------------------------------|
response    | M1|1xx-rel (offer1)               |
            +-> |==============================>| --+
                |                   answer1(PRA)| M3| Acknowledge
                |<===========\  /===============| <-+
                |             \/                |
                |             /\     offer2(UPD)|
                |<===========/  \===============| M2
                |500 (UPD)                      |
                |------------------------------>|
                |2xx-PRA                        |
                |------------------------------>|
                |                               |
 Figure 6: Avoidable message crossing cases 

To avoid the message crossing condition shown in Figure 6 (Avoidable message crossing cases), UA B should not send this UPDATE request at this point. If UA A encounters this message crossing condition, it should reject this UPDATE request with a 500 response.

The situation when a reliable provisional response to INVITE request crosses UPDATE request is shown in Figure 7 (Avoidable message crossing cases).



                A                               B
                |                               |
                |re-INV (offer1)                |
             M1 |==============================>|
                |              answer1 (1xx-rel)|
                |<===========\  /===============| M3
                |             \/                |
                |             /\     offer1(UPD)|
            +-- |<===========/  \===============| M2
            |   |491 (UPD)                      |
Acknowledge |   |------------------------------>|
            |   |PRACK                          |
            +-> |------------------------------>|
                |                               |
 Figure 7: Avoidable message crossing cases 

To avoid the message crossing condition shown in Figure 7 (Avoidable message crossing cases), UA B should not send this UPDATE request at this point. If UA A encounters this message crossing condition, it should reject this UPDATE request with a 491 response.

The situation when a 2xx response to INVITE request crosses UPDATE request is shown in Figure 8 (Avoidable message crossing cases).



                A                               B
                |                               |
                |re-INV (offer1)                |
                |==============================>|
                |                  answer1 (2xx)|
                |<===========\  /===============|
                |             \/                |
                |             /\     offer1(UPD)|
            +-- |<===========/  \===============|
            |   |491 (UPD)                      |
Acknowledge |   |------------------------------>|
            |   |ACK                            |
            +-> |------------------------------>|
                |                               |
 Figure 8: Avoidable message crossing cases 

To avoid the message crossing condition shown in Figure 8 (Avoidable message crossing cases), UA B should not send this UPDATE request at this point. If UA A encounters this message crossing condition, it should reject this UPDATE request with a 491 response.

The situation when a response to UPDATE request crosses PRACK request is shown in Figure 9 (Avoidable message crossing case).



                A                               B
                |                               |
                |                re-INV (offer0)|
                |<------------------------------|
                |1xx-rel (answer0)              |
                |------------------------------>| --+
                |offer1(UPD)                    |   |
             M1 |==============================>|   |
                |              answer1 (2xx-UPD)|   | Acknowledge
                |<===========\  /===============| M3|
                |             \/                |   |
                |             /\     offer2(PRA)| M2|
                |<===========/  \===============| <-+
                |                               |
 Figure 9: Avoidable message crossing case 

To avoid the message crossing condition shown in Figure 9 (Avoidable message crossing case), UA A should not send this UPDATE request at this point. If UA B encounters this message crossing condition, it should reject this UPDATE request with a 491 response.



Table 3 summarize this section. Each action is described in Section 4.3 (Interworking of UPDATE and reINVITE).

     | M1     | M3       | M2        |Action |Action |Figure|
     |(offer1)|(answer1) |(offer2)   | of A  | of B  |      |
     +--------+----------+-----------+-------+-------+------+
     | UPDATE | 2xx-UPD  | UPDATE    |UAS-UcU|       |      |
     |        |          +-----------+       | -     |      |
     |        |          | INVITE    |UAS-UcI|       |      |
     |        |          +-----------+-------+-------+------+
     |        |          | 1xx-INV   |       |       |      |
     |        |          +-----------+UAC-UI,|UAS-UsI| 4,5  |
     |        |          | 2xx-INV   |UAC-IU |UAS-IsU|      |
     |        |          +-----------+-------+-------+------+
     |        |          | PRACK  (*)|UAC-IU |UAS-IcU|  9   |
     +--------+----------+-----------+-------+-------+------+
     | PRACK  | 2xx-PRA  | UPDATE    |UAS-IcU|       |      |
     +--------+----------+-----------+       |       |      |
     | 2xx-INV| ACK      | UPDATE    |UAS-IsU| -     |      |
     |        |          +-----------+       |       |      |
     |        |          | INVITE    |UAS-IsI|       |      |
     +--------+----------+-----------+       +-------+------+
     | 1xx-rel| PRACK    | UPDATE    |UAS-IsU|UAC-IU |  6   |
     +--------+----------+-----------+       |       +------+
     | INVITE | 1xx-rel  | UPDATE (*)|UAS-IcU|UAC-IU |  7   |
     |        +----------+-----------+       |       +------+
     |        | 2xx-INV  | UPDATE (*)|UAS-IcU|UAC-IU |  8   |
     +--------+----------+-----------+-------+-------+------+
     (*) invalid sequences if INVITE request is an initial one
 Table 3: Offer / Answer Crossing Message Sequences 



 TOC 

4.2.  Glare Case Handling

When both ends in a dialog send a new offer at nearly the same time, as described in Figure 10 (Glare Case), a UA may receive a new offer before it receives the answer to the offer it sent. This case is usually called a 'glare' case.



      A                  B
      |offer1      offer2|
   M1 |-------\  /-------| M2
      |        \/        |
      |        /\        |
      |<------/  \------>|
 Figure 10: Glare Case 

When offer2 is in an UPDATE request or (re-)INVITE request, it must be rejected with a 491 or 500 response.

There is a variant of Figure 7 (Avoidable message crossing cases). When offer2 is in a PRACK request (within the current rules, only possible if offer1 is in an UPDATE request), as shown in Figure 11 (Avoidable glare case), UA A has a dilemma.



                A                               B
                |                               |
                |                re-INV (offer0)|
                |<------------------------------|
                |1xx-rel (answer0)              |
                |------------------------------>| --+
                |offer1(UPD)         offer2(PRA)| M2| Acknowledge
             M1 |============\  /===============| <-+
                |             \/                |
                |             /\                |
                |<===========/  \==============>|
                |                      491 (UPD)|
                |<------------------------------|
                |                               |
 Figure 11: Avoidable glare case 

All PRACKs are supposed to be accepted with 200 response, yet there is no way to indicate the problem with a 200 response. At best it could proceed on the assumption that its INVITE will be rejected with a 491. To avoid this glare condition shown in Figure 11 (Avoidable glare case), UA A should not send this UPDATE request at this point. If UA B encounters this glare condition it should reject this UPDATE request with a 491 response.

Glare can also occur when offer2 is in a 1xx or 2xx response. This is a variant of Figure 5 (Avoidable message crossing cases), as shown in Figure 12 (Avoidable glare case).



                A                               B
                |                               |
                |re-INV (no offer)              |
                |------------------------------>| --+ 1st reliable
                |offer1(UPD)              offer2| M2| response
             M1 |============\  /===============| <-+
                |             \/   (1xx-rel/2xx)|
                |             /\                |
                |<===========/  \==============>|
                |                      500 (UPD)|
                |<------------------------------|
                |                               |
 Figure 12: Avoidable glare case 

To avoid this glare condition shown in Figure 12 (Avoidable glare case), UA A should not send this UPDATE request at this point. If UA B encounters this glare condition it should reject this UPDATE request with a 500 response.

There is a variant of Figure 4 (Avoidable message crossing cases), as shown in Figure 13 (Avoidable glare case).



                A                               B
                |                               |
                |offer1(UPD)                    |
                |==========\                    |
                |re-INV     \                   |
                |------------\----------------->| --+
                |(no offer)   \                 |   |1st reliable
                |              \          offer2|   | response
                |<==============\===============| <-+
                |                \ (1xx-rel/2xx)|
                |                 \             |
                |                  \===========>|
                |                      500 (UPD)|
                |<------------------------------|
                |                               |
 Figure 13: Avoidable glare case 

To avoid this glare condition shown in Figure 13 (Avoidable glare case), UA A should not send this reINVITE request at this point. If UA B encounters this glare condition it should reject this UPDATE request with a 500 response.



Table 4 summarize this section. Each action is described in Section 4.3 (Interworking of UPDATE and reINVITE).

    | offer1   | offer2   |Action |Action |Figure|
    |  M1      |  M2      | of A  | of B  |      |
    +----------+----------+-------+-------+------+
    |          | reINVITE |UAS-IcI|UAS-IcI|      |
    | reINVITE +----------+       |       |      |
    |          | UPDATE   |UAS-IcU|UAS-UcI|      |
    +----------+----------+       |       |      |
    |          | UPDATE   |UAS-UcU|UAS-UcU|      |
    |          +----------+-------+       +------+
    |          | 1xx-rel  |       |       |      |
    | UPDATE   +----------+UAC-IU,|UAS-IsU|12,13 |
    |          | 2xx-INV  |UAC-UI |       |      |
    |          +----------+-------+       +------+
    |          | PRACK (*)|UAC-IU |UAS-IcU|  11  |
    +----------+----------+-------+-------+------+
     (*) invalid sequences if INVITE request is an initial one
 Table 4: Offer / Answer Glare Message Sequences 



 TOC 

4.3.  Interworking of UPDATE and reINVITE

Almost all exceptional cases are caused by an interworking of UPDATE and reINVITE. The interworking is described in Section 5 of [RFC3311] (Rosenberg, J., “The Session Initiation Protocol (SIP) UPDATE Method,” October 2002.). And UAC Behavior sending an UPDATE is described in Section 5.1 of [RFC3311] (Rosenberg, J., “The Session Initiation Protocol (SIP) UPDATE Method,” October 2002.). There are two concerns in this section,

  1. It seems to describe different rules for each of initial INVITE and reINVITE. But there is no particular reason why the rules are separated. The lack of restrictions for sending a reINVITE request cause a lot of the problems shown in Section 4.1 (Message Crossing Case Handling).
  2. It seems to describe that a UA may send an UPDATE request after sending or receiving a PRACK request. But it should be "after PRACK transaction is completed by 2xx response", because it causes the message-crossing case shown in Figure 6 (Avoidable message crossing cases)

Since it is assumed that the language in this section itself is non-normative and is justified as a corollary of 3261, we interpret it as follows,

UAC-II:
While an INVITE transaction is incomplete, a UA must not send an another INVITE request.
UAC-UU:
While an UPDATE transaction is incomplete, a UA must not send an another UPDATE request.
UAC-UI:
While an UPDATE transaction is incomplete, a UA should not send a reINVITE request.
UAC-IU:
While an INVITE transaction is incomplete and a PRACK transaction associated with offer-answer is incomplete, a UA should not send an UPDATE request.

UAS Behavior receiving an UPDATE is described in Section 5.2 of [RFC3311] (Rosenberg, J., “The Session Initiation Protocol (SIP) UPDATE Method,” October 2002.). There are two concerns in this section,

  1. There are no description about the interworking of an UPDATE request and an INVITE request without an offer.
  2. There are no description about the interworking of an UPDATE request and reliable response to INVITE with an offer.

We interpret this section as follows,

UAS-IcI:
While an INVITE client transaction is incomplete, a UA must reject an another INVITE request with a 491 response.
UAS-IsI:
While an INVITE server transaction is incomplete, a UA must reject an another INVITE request with a 500 response.
UAS-UcU:
While an UPDATE client transaction is incomplete, a UA must reject an another UPDATE request with a 491 response.
UAS-UsU:
While an UPDATE server transaction is incomplete, a UA must reject an another UPDATE request with a 500 response.
UAS-UcI:
While an UPDATE client transaction is incomplete, a UA should reject a reINVITE request with a 491 response.
UAS-UsI:
While an UPDATE server transaction is incomplete, a UA should reject a reINVITE request with a 500 response.
UAS-IcU:
While an INVITE client transaction is incomplete, and a PRACK transaction associated with offer-answer is incomplete, a UA should reject an UPDATE request with a 491 response.
UAS-IsU:
While an INVITE server transaction is incomplete, and a PRACK transaction associated with offer-answer is incomplete, a UA should reject an UPDATE request with a 500 response.


            A                               B
            |                               |
            |                         UPDATE|
            |<------------------------------|
            |UPDATE                         |
            |==============================>|
            |                            491|
            |<==============================|
            |                               |
 Figure 14: Example of UAC-UU and UAS-UcU 



            A                               B
            |                               |
            |UPDATE CSeq:m                  |
            |------------------------------>|
            |UPDATE CSeq:n(>m)              |
            |==============================>|
            |            500 (UPDATE CSeq:n)|
            |<==============================|
            |                               |
 Figure 15: Example of UAC-UU and UAS-UsU 



            A                               B
            |                               |
            |                 UPDATE(offer1)|
            |<------------------------------|
            |reINVITE(no offer)             |
            |==============================>|
            |                   491 (INVITE)|
            |<==============================|
            |                               |
 Figure 16: Example of UAC-UI and UAS-UcI 



            A                               B
            |                               |
            |UPDATE(offer1)                 |
            |------------------------------>|
            |reINVITE(no offer)             |
            |==============================>|
            |                   500 (INVITE)|
            |<==============================|
            |                               |
 Figure 17: Example of UAC-UU and UAS-UsI 



            A                               B
            |                               |
            |             reINVITE(no offer)|
            |<------------------------------|
            |1xx-rel(offer0)                |
            |------------------------------>|
            |UPDATE(offer1)                 |
            |==============================>|
            |                   491 (UPDATE)|
            |<==============================|
            |                               |
 Figure 18: Example of UAC-IU and UAS-IcU 



            A                               B
            |                               |
            |reINVITE(no offer)             |
            |------------------------------>|
            |                1xx-rel(offer0)|
            |<------------------------------|
            |UPDATE(offer1)                 |
            |==============================>|
            |                   500 (UPDATE)|
            |<==============================|
            |                               |
 Figure 19: Example of UAC-IU and UAS-IsU 

In addition, it is assumed that the UPDATE request in this section include a offer. The interworking of a reINVITE and an UPDATE without an offer is out of scope for this document.



 TOC 

5.  Content of Offers and Answers

While [RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.) and [RFC3312] (Camarillo, G., Marshall, W., and J. Rosenberg, “Integration of Resource Management and Session Initiation Protocol (SIP),” October 2002.) give some guidance, questions remain about exactly what should be included in an offer or answer. This is especially a problem when the common "hold" feature has been activated, and when there is the potential for a multimedia call.

Details of behavior depend on the capabilities and state of the User Agent. The kinds of recommendations that can be made are limited by the model of device capabilities and state that is presumed to exist.

This section focuses on a few key aspects of offers and answers that have been identified as troublesome, and will consider other aspects to be out of scope. This section considers:

The following are out of scope for this document:



 TOC 

5.1.  General Principle for Constructing Offers and Answers

A UA should send an offer that indicates what it, and its user, are interested in using/doing at that time, without regard for what the other party in the call may have indicated previously. This is the case even when the offer is sent in response to an INVITE or re- INVITE that contains no offer. (However in the case of re-INVITE the constraints of [RFC3261] (Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, “SIP: Session Initiation Protocol,” June 2002.) and [RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.) must be observed.)

A UA should send an answer that includes as close an approximation to what the UA and its user are interested in doing at that time, while remaining consistent with the offer/answer rules of [RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.) and other RFCs.

NOTE: "at that time" is important. The device may permit the user to configure which supported media are to be used by default.

In some cases a UA may not have direct knowledge of what it is interested in doing at a particular time. If it is an intermediary it may be able to delegate the decision. In the worst case it may apply a default, such as assuming it wants to use all of its capabilities.



 TOC 

5.2.  Choice of Media Types and Formats to Include and Exclude



 TOC 

5.2.1.  Sending an Initial INVITE with Offer

When a UAC sends an initial INVITE with an offer, it has complete freedom to choose which media type(s) and media format(s) (payload types in the case of RTP) it should include in the offer.

The media types may be all or a subset of the media the UAC is capable of supporting, with the particular subset being determined by the design and configuration (e.g., via [I‑D.ietf‑sipping‑config‑framework] (Channabasappa, S., “A Framework for Session Initiation Protocol User Agent Profile Delivery,” February 2010.)) of the UAC combined with input from the user interface of the UAC.

The media formats may be all or a subset of the media formats the UAC is capable of supporting for the corresponding media type, with the particular subset being determined by the design and configuration of the UAC combined with input from the user interface of the UAC.

Including all supported media formats will maximize the possibility that the other party will have a supported format in common. But including many can result in an unacceptably large SDP body.



 TOC 

5.2.2.  Responding with an Offer when the Initial INVITE has no Offer

When a UAS has received an initial INVITE without an offer, it must include an offer in the first reliable response to the INVITE. It has largely the same options as when sending an initial INVITE with an offer, but there are some differences. The choice may be governed by both static (default) selections of media types as well as dynamic selections made by a user via interaction with the device while it is alerting.

NOTE: The offer may be sent in a provisional response, before the user of the device has been alerted and had an opportunity to select media options for the call. In this case the UAS cannot include any call-specific options from the user of the device. If there is a possibility that the user of the device will wish to change what is offered before answering the call, then special care should be taken. If PRACK and UPDATE are supported by caller and callee then an initial offer can be sent reliably, and changed with an UPDATE if the user desires a change. If PRACK and UPDATE are not supported then the initial offer cannot be changed until the call is fully established. In that case either the offer should be delayed until the 200 is sent, or else the offer should include the minimum set of media the user is able to select.



 TOC 

5.2.3.  Answering an Initial INVITE with Offer

When a UAS receives an initial INVITE with an offer, what media lines the answer may contain is constrained by [RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.). The answer must contain the same number of m-lines as the offer, and they must contain the same media types. Each media line may be accepted, by including a non-zero port number, or rejected by including a zero port number in the answer. The media lines that are accepted should typically be those with types and formats the UAS would have included if it were the offerer.

The media formats the answer may contain are constrained by [RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.). For each accepted m-line in the answer, there must be at least one media format in common with the corresponding m-line of the offer. The UAS may also include other media formats it is able to support at this time. Doing so establishes an asymmetric media format situation, where these "other" media formats may only be sent from the offerer to the answerer. This asymmetric media situation is also limited because it cannot be sustained if there is a subsequent offer/answer exchange in the opposite direction. Also, there is limited value in including these other media formats because there is no assurance that the offerer will be able to use them.

If the UAS does not wish to indicate support for any of the media types in a particular media line of the offer it must reject the corresponding media line, by setting the port number to zero.

When the UAS wishes to reject all of the media lines in the offer, it may send a 488 failure response. Alternatively it may send a reliable non-failure response including all media lines with port numbers set to zero.



 TOC 

5.2.4.  Answering when the Initial INVITE had no Offer

When a UAC has sent an initial INVITE without an offer, and then receives a response with the first offer, it should answer in the same way as a UAS receiving an initial INVITE with an offer.

Because the offer arrives in a response to the INVITE, the UAC cannot reject the message containing the offer. If the UAC wishes to reject the entire offer, it must send a PRACK or ACK request including all the media lines with ports set to zero. Then, if it does not wish to continue the session it may send a CANCEL or BYE request to terminate the dialog.



 TOC 

5.2.5.  Subsequent Offers and Answers

The guidelines above (Section 5.1 (General Principle for Constructing Offers and Answers) and Section 5.2.1 (Sending an Initial INVITE with Offer) through Section 5.2.4 (Answering when the Initial INVITE had no Offer)) apply, but constraints in [RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.) must also be followed. The following are of particular note because they have proven troublesome:

When the new offer is sent in response to an offerless (re)INVITE, it should be constructed according to the General Principle for Constructing Offers and Answers (Section 5.1 (General Principle for Constructing Offers and Answers) ): all codecs the UA is currently willing and able to use should be included, not just the ones that were negotiated by previous offer/answer exchanges. The same is true for media types - so if UA A initially offered audio and video to UA B, and they end up with only audio, and UA B sends an offerless (re)INVITE to UA A, A's resulting offer should most likely re-attempt video, by reusing the zeroed m-line used previously.

NOTE: The behavior above is recommended, but it is not always achievable - for example in some interworking scenarios. Or, the offerer may simply not have enough resources to offer "everything" at that point. Even if the UAS is not able to offer any other SDP that the one currently being used, it should not reject the re-INVITE. Instead, it should generate an offer with the currently used SDP with o- line unchanged.



 TOC 

5.3.  Hold and Resume of media

[RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.) specifies (using non-normative language) that "hold" should be indicated in an established session by sending a new offer containing "a=sendonly" for each media stream to be held. An answerer is then to respond with "a=recvonly" to acknowledge that the hold request has been understood.

Note that the use of sendonly/recvonly is not limited to hold. These may be used for other reasons, such as devices that are only capable of sending or receiving. So receiving an offer with "a=sendonly" must not be treated as a certain indication that the offerer has placed the media stream on hold.

This model is based on an assumption that the UA initiating the hold will want to play Music on Hold, which is not always the case. A UA may, if desired, initiate hold by offering "a=inactive" if it does not intend to transmit any media while in hold status.

The rules of [RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.) constrain what may be in an answer when the offer contains "sendonly", "recvonly", or "inactive" in an a= line. But they do not constrain what must be in a subsequent offer. The General Principle for Constructing Offers and Answers (Section 5.1 (General Principle for Constructing Offers and Answers)) is important here. The initiation of "hold" is a local action. It should reflect the desired state of the UA. It then affects what the UA includes in offers and answers until the local state is reset.

The receipt of an offer containing "a=sendonly" or "a=inactive" and the sending of a compatible answer should not change the desired state of the recipient. However, a UA that has been "placed on hold" may itself desire to initiate its own hold status, based on local input.

If UA2 has previously been "placed on hold" by UA1, via receipt of "a=sendonly", then it may initiate its own hold by sending a new offer containing "a=sendonly" to UA1. Upon receipt of that, UA1 will answer with "a=inactive" because that is the only valid answer that reflects its desire not to receive media.

NOTE: Section 8.4 of [RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.) contains a conflicting recommendation that the offer contain "a=inactive" in this case. We interpret that recommendation to be non-normative. The use of "a=sendonly" in this case will never produce a worse outcome, and can produce a better outcome in useful cases.

Once in this state, to resume a two way exchange of media each side must reset its local hold status. If UA1 is first to go off hold it will then send an offer with "a=sendrecv". The UA2 will respond with its desired state of "a=sendonly" because that is a permitted response. When UA2 desires to also resume, it will send an offer with "a=sendrecv". In this case, because UA1 has the same desire it will respond with "a=sendrecv". In the same case, when UA2 receives the offer with "a=sendrecv", if it has decided it wants to reset its local hold but has not yet signaled the intent, it may send "a=sendrecv" in the answer.

If UA2 has been "placed on hold" by UA1 via receipt of "a=inactive", and subsequently wants to initiate its own hold, also using "a=inactive", it need not send a new offer, since the only valid response is "a=inactive" and that is already in effect. However, its local desired state will now be either "inactive" or "a=sendonly". This affects what it will send in future offers and answers.

If a UA has occasion to send another offer in the session, without any desire to change the hold status (e.g. in response to a re- INVITE without an offer, or when sending a re-INVITE to refresh the session timer) it should follow the General Principle for Constructing Offers and Answers (Section 5.1 (General Principle for Constructing Offers and Answers)). If it previously initiated a "hold" by sending "a=sendonly" or "a=inactive" then it should offer that again. If it had not previously initiated "hold" then it should offer "a=sendrecv", even if it had previously been forced to answer something else. Without this behavior it is possible to get "stuck on hold" in some cases, especially when a third-party call controller is involved.



 TOC 

5.4.  Behavior on receiving SDP with c=0.0.0.0

[RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.) specifies that an agent MUST be capable of receiving SDP with a connection address of 0.0.0.0, in which case it means that neither RTP nor RTCP should be sent to the peer.

If a UA generates an answer to the offer received with "c=IN IP4 0.0.0.0", the direction attribute of the accepted media stream in the answer must still be based on direction attribute of the offered stream and rules specified in [RFC3264] (Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” June 2002.) to form the direction a-line in the answer. There is no clear rule about the use of "c=IN IP4 0.0.0.0" in the answer - it may be used or c-line with a valid IP address may be used. RTP/RTCP will not be sent toward an address of 0.0.0.0 because it is an invalid address.



 TOC 

6.  IANA Considerations

This document has no actions for IANA.



 TOC 

7.  Security Considerations

There are not any security issues beyond the referenced RFCs.



 TOC 

8.  Acknowledgement

The authors would like to thank Christer Holmberg, Rajeev Seth, Nataraju A B, Byron Campen, Jonathan Rosenberg, Gonzalo Camarillo and Yang Gao for their thorough reviews and comments. Many of their suggestions and ideas have been incorporated in this document. Also, a big thank you to Sawada Takuya, who was first author of this document.



 TOC 

9.  References



 TOC 

9.1. Normative References

[RFC2119] Bradner, S., “Key words for use in RFCs to Indicate Requirement Levels,” BCP 14, RFC 2119, March 1997 (TXT, HTML, XML).
[RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, “SIP: Session Initiation Protocol,” RFC 3261, June 2002 (TXT).
[RFC3262] Rosenberg, J. and H. Schulzrinne, “Reliability of Provisional Responses in Session Initiation Protocol (SIP),” RFC 3262, June 2002 (TXT).
[RFC3264] Rosenberg, J. and H. Schulzrinne, “An Offer/Answer Model with Session Description Protocol (SDP),” RFC 3264, June 2002 (TXT).
[RFC3311] Rosenberg, J., “The Session Initiation Protocol (SIP) UPDATE Method,” RFC 3311, October 2002 (TXT).
[RFC3312] Camarillo, G., Marshall, W., and J. Rosenberg, “Integration of Resource Management and Session Initiation Protocol (SIP),” RFC 3312, October 2002 (TXT, PS, PDF).
[I-D.camarillo-sipcore-reinvite] Camarillo, G., Holmberg, C., and G. yang, “Re-INVITE and Target-refresh Request Handling in the Session Initiation Protocol (SIP),” draft-camarillo-sipcore-reinvite-01 (work in progress), October 2009 (TXT).


 TOC 

9.2. Informative References

[RFC3959] Camarillo, G., “The Early Session Disposition Type for the Session Initiation Protocol (SIP),” RFC 3959, December 2004 (TXT).
[I-D.ietf-sipping-config-framework] Channabasappa, S., “A Framework for Session Initiation Protocol User Agent Profile Delivery,” draft-ietf-sipping-config-framework-17 (work in progress), February 2010 (TXT).


 TOC 

Authors' Addresses

  OKUMURA Shinji
  Softfront
  28-196, Noth9, West15, Chuo-ku
  Sapporo, Hokkaido 060-0009
  Japan
Email:  shinji.okumura@softfront.jp
  
  Paul H. Kyzivat
  Cisco Systems, Inc.
  1414 Massachusetts Avenue
  Boxborough, MA 01719
  USA
Email:  pkyzivat@cisco.com