Definitions of Managed Objects for APPN April 01, 1996 Bob Clouston (editor) Cisco Systems clouston@cisco.com Bob Moore (editor) IBM Corporation remoore@ralvm6.vnet.ibm.com 1. Status of this Memo This document is an Internet-Draft. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months. Internet-Drafts may be updated, replaced, or obsoleted by other documents at any time. It is not appropriate to use Internet-Drafts as reference material or to cite them other than as a working draft or work in progress. To learn the current status of any Internet-Draft, please check the 1id-abstracts.txt listing contained in the Internet-Drafts Shadow Directories on ds.internic.net, nic.nordu.net, ftp.isi.edu, or munnari.oz.au. 2. Introduction This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it defines objects for monitoring and controlling network Expires October 01, 1996 [Page 1] Internet Draft SNANAU APPN MIB April 1996 devices with APPN (Advanced Peer-to-Peer Networking) capabilities. This memo identifies managed objects for the SNA APPN protocol. This memo does not specify a standard for the Internet community. 3. The SNMP Network Management Framework The SNMP Network Management Framework consists of several components. For the purpose of this specification, the applicable components of the Framework are the SMI and related documents [1, 2, 3], which define the mechanisms used for describing and naming objects for the purpose of management. The Framework permits new objects to be defined for the purpose of experimentation and evaluation. 4. Overview This document identifies the proposed set of objects for monitoring the configuration and active characteristics of devices with APPN capabilities, and for controlling certain characteristics. APPN is the aspect of SNA that supports peer-to-peer networking. These networks transport both independent and dependent LU session traffic. See the SNANAU APPC MIB [7] and the SNA NAU MIB (RFC 1666 [8]) for management of these sessions. See also the DLUR MIB[9], and the HPR MIB[10] for management of extensions to the APPN architecture. In this document, we describe APPN managed objects. An APPN network is comprised of various types of nodes, and transmission groups (TGs) that connect the nodes. Network nodes (NNs) provide directory and routing functions for session establishment. NNs may be session end points or intermediate nodes in a session. A border node is a type of network node that connects networks together for session establishment without fully merging them. End nodes (ENs) are session end points that receive directory and routing functions from network nodes, over control-point to control-point (CP-CP) sessions. Low-entry networking (LEN) nodes are also session end points, but do not support CP-CP sessions, and therefore need additional manual configuration definitions to establish sessions in an APPN network. ENs and LEN nodes may have minimal directory and routing functions to establish control sessions (ENs) or to connect into the APPN network (LEN nodes). Virtual routing nodes (VRNs) are not really nodes, but rather common definitions among actual nodes in a shared transport facility such as a LAN that allow these actual nodes to temporarily establish a logical link with Expires October 01, 1996 [Page 2] Internet Draft SNANAU APPN MIB April 1996 one another without defining each other's link-level addressing information. Ports and link stations are the node's interface to the data link control (DLC), which provides the physical transport, or to another protocol such as Data Link Switching (DLSw), which provides transport over an IP network. See the SNADLC SDLC MIB[11], the SNADLC LLCMIB[12], and the DLSw MIB[13]. A link station uses a port to make a connection to another node. This connection establishes a TG between the two nodes. The directory and routing functions enable an NN to find where an LU is located in the network, and calculate the optimal route for the session based on the requested class of service (COS). A network node saves the LU information in a directory database, which is built from LUs defined locally, LU registration from served end nodes, and LUs learned from network searches. Each NN maintains a local class-of-service database that assigns a routing weight, or relative cost, to each resource for each class of service. For example, the #INTER COS assigns a lower weight to TGs with a greater effective capacity, while the #BATCH COS favors TGs with a lower relative cost per byte. A node saves network topology information (on NNs, VRNs, and TGs between them) in a network topology database. The topology information includes state and routing characteristics. Topology information is exchanged between NNs over CP-CP sessions such that the database is fully replicated at each NN. Information on TGs from NNs to ENs are kept in a local topology database. Local topology information is shared with other NNs only during the session establishment process, to give the NN responsible for route calculation the necessary information for end-to- end route calculation. SNA names such as LU names, CP names, COS names, and mode names can be padded with blanks (space characters) in SNA formats. These blanks are nonsignificant. For example, in a BIND RU a COS name of "#INTER" with a length of 6 is identical to a COS name of "#INTER " with a length of 8. However, in this MIB, nonsignificant blanks are not included by the agent. Using the COS name from the previous example, an agent would return a length of 6 and the string "#INTER" with no blanks for appnCosName, regardless of how it appears in the BIND RU or in internal storage. The lone exception is the all blank mode name, for which the agent returns a length of 8 and the string " " (8 blank spaces). When an SNA name is functioning as a table index, an agent treats Expires October 01, 1996 [Page 3] Internet Draft SNANAU APPN MIB April 1996 trailing blanks as significant. If a management station requests the objects from a row with index "#INTER ", the agent does not match this to the row with index "#INTER". Since an agent has no nonsignificant blanks in any of its table indices, the only reason for a Management Station to include them would be to start GetNext processing at a chosen point in a table. For example, a GetNext request with index "M " would start retrieval from a table at the first row with an 8-character index beginning with M or a letter after M. The SNA/APPN terms and overall architecture are documented in [4], [5], and [6]. Highlights of the management functions supported by the APPN MIB module include the following: o Activating and deactivating ports and link stations. o Monitoring of configuration parameters related to the node, ports, link stations, virtual routing nodes, and classes of service. o Monitoring of operational parameters related to ports, link stations, virtual routing nodes, topology, directory, and intermediate sessions. o Historical information about link station errors during connection establishment, or that caused the connection to terminate. o Deactivating intermediate sessions. o Traps for SNA/MS Alert conditions. This MIB module does not support: o Configuration of APPN nodes. o Monitoring and control of endpoint sessions. o Dependent LU Requester (DLUR) management. o High-Performance Routing (HPR) management. Expires October 01, 1996 [Page 4] Internet Draft SNANAU APPN MIB April 1996 4.1. APPN MIB Structure The APPN MIB module contains the following groups of objects: o appnNode - objects related to the APPN node for all node types. o appnNn - objects to represent the network nodes, virtual routing nodes, and TGs between these nodes that make up the APPN network topology database maintained in NNs. o appnLocalTopology - objects to represent nodes and TGs between nodes in the local topology database maintained in all nodes. o appnDir - objects related to LU location information from the node's directory database. o appnCos - objects related to classes of service information. o appnSessIntermediate - objects related to intermediate sessions that pass through this node. These groups are described below in more detail. 4.1.1. appnNode group The appnNode group consists of the following tables and objects: 1) appnGeneralInfoAndCaps This group of objects describes general information about the APPN node. The type of information includes the node type and the time since this node was initialized. 2) appnNnUniqueInfoAndCaps This group of objects describes information specific to network nodes such as node routing characteristics. 3) appnEnUniqueInfoAndCaps This group of objects describes information specific to end nodes, including its network node server. Expires October 01, 1996 [Page 5] Internet Draft SNANAU APPN MIB April 1996 4) appnPortInformation This includes the appnPortTable, which describes the configuration and current status of the ports used by APPN, including the port state and DLC type. 5) appnLinkStationInformation This includes the appnNodeLsTable, which describe the configuration and current status of the link stations used by APPN, including the link state and port name; and the appnLsStatusTable, which provides information about errors this node encountered with connections to adjacent nodes, such as the sense data captured during connection failures. It is a product option to decide how many appnLsStatusTable entries are kept. 6) appnVrnInfo This includes the appnVrnTable, which describes the relationship between virtual routing nodes' TGs described in the appnLocalTgTable with ports in the appnPortTable. 4.1.2. appnNn group The appnNn group consists of the following objects and tables 1) appnNnTopo These objects contain general information about the network topology database including the number of nodes present, and the number of TDU wars the node has detected. 2) appnNnTopology This includes tables representing the APPN network topology database. This includes the network nodes, virtual routing nodes, and TGs between these nodes, as well as the information about these resources carried in topology updates. The tables are first indexed by the same flow reduction sequence number (FRSN) used in topology exchanges between NNs. This allows a management station to retrieve only incremental updates, since the agent will update the FRSN of new or changed resources. Expires October 01, 1996 [Page 6] Internet Draft SNANAU APPN MIB April 1996 4.1.3. appnLocalTopology group The appnLocalTopology group consists of the following objects and tables: 1) appnLocalThisNode a) appnLocalGeneral Contains the local node and type. b) appnLocalNnSpecific These objects contains routing information about the local network node. c) appnLocalTg This table represents information about this node's local TGs. 2) appnLocalEnTopology This table represent TG information for EN TGs learned by the NN via TG registration with the local node. 4.1.4. appnDir group The appnDir group consists of the following objects and tables: 1) appnDirPerf These objects represent information related to information about the directory database and directory searches involving this node. 2) appnDirTable This table represents the directory database, listing LUs known to this node, along with the owning node of the LU and the serving NN of the owning node. 4.1.5. appnCos group The appnCos group consists of the following tables: Expires October 01, 1996 [Page 7] Internet Draft SNANAU APPN MIB April 1996 1) appnCosModeTable This table represents the mode to class of service mapping. 2) appnCosNameTable This table represents the tranmission priority for each class of service. 3) appnCosNodeRowTable This table represents the node-row information for each class of service, including the weight of each node. 3) appnCosTGRowTable This table represents the TG-row information for each class of service, including the weight of each TG. 4.1.6. appnSessIntermediate group The appnSessIntermediate group consists of the following objects and tables: 1) appnIsInGlobal These objects allow control of the collection of intermediate session information such as RSCVs and counters. 2) appnIsInTable This table contains information on active intermediate sessions. 3) appnIsRtpTable This table contains information on active intermediate sessions that are being transported on RTP connections by HPR. 4.1.7. appnTraps One APPN trap is defined. It is intended to correspond to SNA/MS Alerts, but is optional for a product to implement this trap. The trap identifies the Alert ID number and, where possible, the affected resource. Expires October 01, 1996 [Page 8] Internet Draft SNANAU APPN MIB April 1996 5. Definitions APPN-MIB DEFINITIONS ::= BEGIN IMPORTS IANAifType FROM IANAifType-MIB DisplayString, VariablePointer, DateAndTime, TEXTUAL-CONVENTION FROM SNMPv2-TC experimental, Counter32, Gauge32, Integer32, TimeTicks, OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF; appnMIB MODULE-IDENTITY LAST-UPDATED "9604010000Z" ORGANIZATION "IETF SNA NAU MIB WG / AIW APPN/HPR MIBs SIG" CONTACT-INFO " Bob Clouston Cisco Systems 7025 Kit Creek Road P.O. Box 14987 Research Triangle Park, NC 27709, USA Tel: 1 919 472 2333 E-mail: clouston@cisco.com Bob Moore IBM Corporation 800 Park Offices Drive CNMA/664 P.O. Box 12195 Research Triangle Park, NC 27709, USA Tel: 1 919 254 4436 E-mail: remoore@ralvm6.vnet.ibm.com " DESCRIPTION "This is the MIB module for objects used to Expires October 01, 1996 [Page 9] Internet Draft SNANAU APPN MIB April 1996 manage network devices with APPN capabilities." ::= { experimental 1000 } -- ********************************************************************* appnObjects OBJECT IDENTIFIER ::= { appnMIB 1 } -- ********************************************************************* -- ********************************************************************* -- Textual Convention -- --------------------------------------------------------------------- SnaSenseData ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "To facilitate their display by a Management Station, sense data objects in the MIB are represented as DisplayStrings of size 8. Eight '0' characters indicates that no sense data identifying an SNA error condition is available." SYNTAX DisplayString (SIZE (8)) -- ******************** The APPN Node Group **************************** appnNode OBJECT IDENTIFIER ::= { appnObjects 1 } appnGeneralInfoAndCaps OBJECT IDENTIFIER ::= { appnNode 1 } appnNnUniqueInfoAndCaps OBJECT IDENTIFIER ::= { appnNode 2 } appnEnUniqueCaps OBJECT IDENTIFIER ::= { appnNode 3 } appnPortInformation OBJECT IDENTIFIER ::= { appnNode 4 } appnLinkStationInformation OBJECT IDENTIFIER ::= { appnNode 5 } appnVrnInfo OBJECT IDENTIFIER ::= { appnNode 6 } -- This group provides global information about an APPN network node, -- an APPN end node, or an LEN node. -- The first section applies to all three node types. -- The second section applies only to APPN network nodes. -- The third section applies only to APPN end nodes and to LEN nodes. -- The fourth section applies to all three node types. -- The fifth section applies to all three node types. -- The sixth section applies only to APPN network nodes. -- APPN General Information -- This section applies to both APPN network and end nodes, and to -- LEN nodes. appnNodeCpName OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) Expires October 01, 1996 [Page 10] Internet Draft SNANAU APPN MIB April 1996 MAX-ACCESS read-only STATUS current DESCRIPTION "Administratively assigned network name for this node in the format NetId.CpName." ::= { appnGeneralInfoAndCaps 1 } appnNodeMibVersion OBJECT-TYPE SYNTAX DisplayString (SIZE (11)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of LAST-UPDATED from this module's MODULE-IDENTITY macro. This object gives a Management Station an easy way of determining the level of the MIB supported by an agent." ::= { appnGeneralInfoAndCaps 2 } appnNodeId OBJECT-TYPE SYNTAX DisplayString (SIZE (8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The node_id consists of two parts: The block number is the first three digits of the node_id. These 3 hexadecimal digits identify the product. The ID number is the last 5 digits of the node_id. These 5 hexadecimal digits are administratively defined and combined with the 3-digit block number form the node_id. This node_id is used to identify the local node in XIDs. A unique value is required for connections to SNA subarea. In some implementations, the value of 'bbb00000' (where 'bbb' represents a 3-digit block number) is returned to mean that the ID number is not unique on this node." ::= { appnGeneralInfoAndCaps 3 } appnNodeType OBJECT-TYPE SYNTAX INTEGER { networkNode(1), endNode(2), t21len(4) } Expires October 01, 1996 [Page 11] Internet Draft SNANAU APPN MIB April 1996 MAX-ACCESS read-only STATUS current DESCRIPTION "Type of APPN node, either network, LEN, or end node." ::= { appnGeneralInfoAndCaps 4 } appnNodeUpTime OBJECT-TYPE SYNTAX TimeTicks UNITS "hundredths of a second" MAX-ACCESS read-only STATUS current DESCRIPTION "Amount of time (in hundredths of a second) since the APPN node was last re-initialized." ::= { appnGeneralInfoAndCaps 5 } appnNodeParallelTg OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this node supports parallel TGs." ::= { appnGeneralInfoAndCaps 6 } appnNodeAdaptiveBindPacing OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this node supports adaptive bind pacing for dependent LUs." ::= { appnGeneralInfoAndCaps 7 } appnNodeHprSupport OBJECT-TYPE SYNTAX INTEGER { noHprSupport(1), hprBaseOnly(2), rtpTower(3), controlFlowsOverRtpTower(4) } MAX-ACCESS read-only STATUS current Expires October 01, 1996 [Page 12] Internet Draft SNANAU APPN MIB April 1996 DESCRIPTION "Indicates this node's level of support for high performance routing (HPR). This object corresponds to cv4580, byte 9, bits 3-4." ::= { appnGeneralInfoAndCaps 8 } appnNodeMaxSessPerRtpConn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the maximum number of sessions that APPN would put on any HPR connection. The value is zero if not applicable." ::= { appnGeneralInfoAndCaps 9 } appnNodeHprIntRteSetups OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of HPR route setups received for routes passing through this node since the node was last re-initialized." ::= { appnGeneralInfoAndCaps 10 } appnNodeHprIntRteRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of HPR route setups rejected by this node for routes passing through it since the node was last re-initialized." ::= { appnGeneralInfoAndCaps 11 } appnNodeHprOrgRteSetups OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION Expires October 01, 1996 [Page 13] Internet Draft SNANAU APPN MIB April 1996 "The total number of HPR route setups sent for routes originating in this node since the node was last re-initialized." ::= { appnGeneralInfoAndCaps 12 } appnNodeHprOrgRteRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of HPR route setups rejected by other nodes for routes originating in this node since the node was last re-initialized." ::= { appnGeneralInfoAndCaps 13 } appnNodeHprEndRteSetups OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of HPR route setups received for routes ending in this node since the node was last re-initialized." ::= { appnGeneralInfoAndCaps 14 } appnNodeHprEndRteRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of HPR route setups rejected by this node for routes ending in it since the node was last re-initialized." ::= { appnGeneralInfoAndCaps 15 } -- ********************************************************************* -- APPN Network Node Information -- This section provides global information about an APPN network node. appnNodeNnCentralDirectory OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current Expires October 01, 1996 [Page 14] Internet Draft SNANAU APPN MIB April 1996 DESCRIPTION "Indicates whether this node supports central directory services. This object corresponds to cv4580, byte 8, bit 1." ::= { appnNnUniqueInfoAndCaps 1 } appnNodeNnTreeCache OBJECT-TYPE SYNTAX INTEGER { noCache(1), cacheNoIncrUpdate(2), cacheWithIncrUpdate(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this node supports route tree cache, and if so, incremental updates to the route tree cache." ::= { appnNnUniqueInfoAndCaps 2 } appnNodeNnRouteAddResist OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Route addition resistance. This administratively assigned value indicates the relative desirability of using this node for intermediate session traffic. The value, which can be any integer 0-255, is used in route computation. The lower the value, the more desirable the node is for intermediate routing. This object corresponds to cv4580, byte 6." ::= { appnNnUniqueInfoAndCaps 3 } appnNodeNnIsr OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the node supports intermediate session routing. Expires October 01, 1996 [Page 15] Internet Draft SNANAU APPN MIB April 1996 This object corresponds to cv4580, byte 8, bit 2." ::= { appnNnUniqueInfoAndCaps 4 } appnNodeNnFrsn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The last flow-reduction sequence number (FRSN) sent by this node in a topology update to an adjacent network node." ::= { appnNnUniqueInfoAndCaps 5 } appnNodeNnPeriBorderSup OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this node has peripheral border node support. This object corresponds to cv4580, byte 9, bit 0." ::= { appnNnUniqueInfoAndCaps 6 } appnNodeNnInterchangeSup OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this node has interchange node support. This object corresponds to cv4580, byte 9, bit 1." ::= { appnNnUniqueInfoAndCaps 7 } appnNodeNnExteBorderSup OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this node has extended border node support. This object corresponds to cv4580, byte 9, bit 2." Expires October 01, 1996 [Page 16] Internet Draft SNANAU APPN MIB April 1996 ::= { appnNnUniqueInfoAndCaps 8 } appnNodeNnSafeStoreFreq OBJECT-TYPE SYNTAX Integer32 UNITS "TDUs" MAX-ACCESS read-write STATUS current DESCRIPTION "The topology safe store frequency. If the total number of topology database updates received by this node exceeds this non-zero value by an even multiple, the topology database is saved. A value of zero indicates that the topology database is not being saved." ::= { appnNnUniqueInfoAndCaps 9 } appnNodeNnRsn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Resource sequence number for this node, which it assigns and controls. This object corresponds to cv4580, bytes 2-5." ::= { appnNnUniqueInfoAndCaps 10 } appnNodeNnCongested OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this node is congested. Other network nodes stop routing traffic to this node while this flag is on. This object corresponds to cv4580, byte 7, bit 0." ::= { appnNnUniqueInfoAndCaps 11 } appnNodeNnIsrDepleted OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current Expires October 01, 1996 [Page 17] Internet Draft SNANAU APPN MIB April 1996 DESCRIPTION "Indicate whether intermediated session routing resources are depleted. Other network nodes stop routing traffic through this node while this flag is on. This object corresponds to cv4580, byte 7, bit 1." ::= { appnNnUniqueInfoAndCaps 12 } appnNodeNnQuiescing OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the node is quiescing. This object corresponds to cv4580, byte 7, bit 5." ::= { appnNnUniqueInfoAndCaps 13 } appnNodeNnGateway OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the node has gateway services support. This object corresponds to cv4580, byte 8, bit 0." ::= { appnNnUniqueInfoAndCaps 14 } -- ********************************************************************* -- APPN End Node Information appnNodeEnModeCosMap OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this end node supports mode name to COS name mapping." ::= { appnEnUniqueCaps 1 } appnNodeEnNnServer OBJECT-TYPE Expires October 01, 1996 [Page 18] Internet Draft SNANAU APPN MIB April 1996 SYNTAX DisplayString (SIZE (0 | 3..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The fully qualified name of the current NN server for this end node. Format is NetId.CpName. The value is a zero-length string when there is no active NN server." ::= { appnEnUniqueCaps 2 } appnNodeEnLuSearch OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the node is to be searched for LUs as part of a network broadcast search." ::= { appnEnUniqueCaps 3 } -- ********************************************************************* -- APPN Port information -- appnPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Port table describes the configuration and current status of the ports used by APPN. When it is known to the APPN component, an OBJECT IDENTIFIER pointing to additional information related to the port is included. This may, but need not, be the value of ifIndex for a DLC immediately 'below' the port." ::= { appnPortInformation 1 } appnPortEntry OBJECT-TYPE SYNTAX AppnPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port name is used as the index to this table." Expires October 01, 1996 [Page 19] Internet Draft SNANAU APPN MIB April 1996 INDEX { appnPortName } ::= { appnPortTable 1 } AppnPortEntry ::= SEQUENCE { appnPortName DisplayString, appnPortAdminState INTEGER, appnPortOperState INTEGER, appnPortDlcType IANAifType, appnPortPortType INTEGER, appnPortSIMRIM INTEGER, appnPortLsRole INTEGER, appnPortNegotLs INTEGER, appnPortDynamicLinkSupport INTEGER, appnPortMaxRcvBtuSize INTEGER, appnPortMaxIframeWindow Integer32, appnPortDefLsGoodXids Counter32, appnPortDefLsBadXids Counter32, appnPortDynLsGoodXids Counter32, appnPortDynLsBadXids Counter32, appnPortSpecific OBJECT IDENTIFIER, appnPortDlcLocalAddr DisplayString } appnPortName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..10)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Administratively assigned name for this APPN port." ::= { appnPortEntry 1 } appnPortAdminState OBJECT-TYPE SYNTAX INTEGER { inactive(1), active(3), ready(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Object by which a Management Station can activate or deactivate a port, by setting the value to active(3) or inactive(1), respectively. The value ready(5) has no meaning Expires October 01, 1996 [Page 20] Internet Draft SNANAU APPN MIB April 1996 on a set operation; it is returned in response to a get operation if no set operation has been directed to this object." ::= { appnPortEntry 2 } appnPortOperState OBJECT-TYPE SYNTAX INTEGER { inactive(1), pendactive(2), active(3), pendinact(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current state of this port." ::= { appnPortEntry 3 } appnPortDlcType OBJECT-TYPE SYNTAX IANAifType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of DLC interface, distinguished according to the protocol immediately 'below' this layer." ::= { appnPortEntry 4 } appnPortPortType OBJECT-TYPE SYNTAX INTEGER { leased(1), switched(2), sharedAccessFacilities(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the type of line used by this port." ::= { appnPortEntry 5 } appnPortSIMRIM OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only Expires October 01, 1996 [Page 21] Internet Draft SNANAU APPN MIB April 1996 STATUS current DESCRIPTION "Indicates whether Set Initialization Mode (SIM) and Receive Initialization Mode (RIM) are supported for this port." ::= { appnPortEntry 6 } appnPortLsRole OBJECT-TYPE SYNTAX INTEGER { primary(1), secondary(2), negotiable(3), abm(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Initial role for LSs activated through this port. The values map to the following settings in the initial XID: primary(1): ABM support = 0 ( = NRM) role = 01 ( = primary) secondary(2): ABM support = 0 ( = NRM) role = 00 ( = secondary) negotiable(3): ABM support = 0 ( = NRM) role = 11 ( = negotiable) abm(4): ABM support = 1 ( = ABM) role = 11 ( = negotiable)" ::= { appnPortEntry 7 } appnPortNegotLs OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the node supports negotiable link stations for this port." ::= { appnPortEntry 8 } appnPortDynamicLinkSupport OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION Expires October 01, 1996 [Page 22] Internet Draft SNANAU APPN MIB April 1996 "Indicates whether this node allows call-in on this port from nodes not defined locally." ::= { appnPortEntry 9 } appnPortMaxRcvBtuSize OBJECT-TYPE SYNTAX INTEGER (99..32767) UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum Basic Transmission Size (BTU) that a link station on this port can receive. This object corresponds to bytes 21-22 of XID3." ::= { appnPortEntry 10 } appnPortMaxIframeWindow OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of I-frames that can be received by the XID sender before an acknowledgement is received." ::= { appnPortEntry 11 } appnPortDefLsGoodXids OBJECT-TYPE SYNTAX Counter32 UNITS "XID exchanges" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of successful XID exchanges that have occurred on all defined link stations on this port since the last time this port was started." ::= { appnPortEntry 12 } appnPortDefLsBadXids OBJECT-TYPE SYNTAX Counter32 UNITS "XID exchanges" MAX-ACCESS read-only STATUS current DESCRIPTION Expires October 01, 1996 [Page 23] Internet Draft SNANAU APPN MIB April 1996 "The total number of unsuccessful XID exchanges that have occurred on all defined link stations on this port since the last time this port was started." ::= { appnPortEntry 13 } appnPortDynLsGoodXids OBJECT-TYPE SYNTAX Counter32 UNITS "XID exchanges" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of successful XID exchanges that have occurred on all dynamic link stations on this port since the last time this port was started." ::= { appnPortEntry 14 } appnPortDynLsBadXids OBJECT-TYPE SYNTAX Counter32 UNITS "XID exchanges" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of unsuccessful XID exchanges that have occurred on all dynamic link stations on this port since the last time this port was started." ::= { appnPortEntry 15 } appnPortSpecific OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the object, e.g., one in a DLC-specific MIB, that can provide additional information related to this port." ::= { appnPortEntry 16 } appnPortDlcLocalAddr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Local DLC address of this port, represented as a Expires October 01, 1996 [Page 24] Internet Draft SNANAU APPN MIB April 1996 DisplayString." ::= { appnPortEntry 17 } -- ********************************************************************* -- APPN Link Station Information -- appnLsTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnLsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains detailed information about the link station configuration and its current status." ::= { appnLinkStationInformation 1 } appnLsEntry OBJECT-TYPE SYNTAX AppnLsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by the link station name." INDEX { appnLsName } ::= { appnLsTable 1 } AppnLsEntry ::= SEQUENCE { appnLsName DisplayString, appnLsAdminState INTEGER, appnLsOperState INTEGER, appnLsPortName DisplayString, appnLsDlcType IANAifType, appnLsDynamic INTEGER, appnLsAdjCpName DisplayString, appnLsAdjNodeType INTEGER, appnLsTgNum INTEGER, appnLsLimResource INTEGER, appnLsActOnDemand INTEGER, appnLsMigration INTEGER, appnLsPartnerNodeId DisplayString, Expires October 01, 1996 [Page 25] Internet Draft SNANAU APPN MIB April 1996 appnLsCpCpSessionSupport INTEGER, appnLsMaxSendBtuSize INTEGER, -- performance data appnLsInXidBytes Counter32, appnLsInMsgBytes Counter32, appnLsInXidFrames Counter32, appnLsInMsgFrames Counter32, appnLsOutXidBytes Counter32, appnLsOutMsgBytes Counter32, appnLsOutXidFrames Counter32, appnLsOutMsgFrames Counter32, -- propagation delay appnLsEchoRsps Counter32, appnLsCurrentDelay Integer32, appnLsMaxDelay Integer32, appnLsMinDelay Integer32, appnLsMaxDelayTime DateAndTime, -- XID Statistics appnLsGoodXids Counter32, appnLsBadXids Counter32, -- DLC-specific appnLsSpecific OBJECT IDENTIFIER, appnLsActiveTime TimeTicks, appnLsCurrentStateTime TimeTicks, -- HPR-specific appnLsHprSup INTEGER, appnLsErrRecoSup INTEGER, appnLsForAnrLabel OCTET STRING, appnLsRevAnrLabel OCTET STRING, appnLsCpCpNceId OCTET STRING, appnLsRouteNceId OCTET STRING, appnLsBfNceId OCTET STRING, appnLsLocalAddr DisplayString, appnLsRemoteAddr DisplayString, appnLsRemoteLsName DisplayString } appnLsName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..10)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Administratively assigned name for the link station. The name can be from one to ten characters." Expires October 01, 1996 [Page 26] Internet Draft SNANAU APPN MIB April 1996 ::= { appnLsEntry 1 } appnLsAdminState OBJECT-TYPE SYNTAX INTEGER { inactive(1), active(7), ready(99) } MAX-ACCESS read-write STATUS current DESCRIPTION "Object by which a Management Station can activate or deactivate a link station, by setting the value to active(7) or inactive(1), respectively. The value ready(99) has no meaning on a set operation; it is returned in response to a get operation if no set operation has been directed to this object." ::= { appnLsEntry 2 } appnLsOperState OBJECT-TYPE SYNTAX INTEGER { inactive(1), sentConnectOut(2), -- pending active pendXidExch(3), -- pending active sendActAs(4), -- pending active sendSetMode(5), -- pending active otherPendingActive(6),-- pending active active(7), sentDeactAsOrd(8), -- pending inactive sentDiscOrd(9), -- pending inactive sentDiscImmed(10), -- pending inactive otherPendingInact(11) -- pending inactive } MAX-ACCESS read-only STATUS current DESCRIPTION "State of this link station." ::= { appnLsEntry 3 } appnLsPortName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..10)) MAX-ACCESS read-only STATUS current DESCRIPTION Expires October 01, 1996 [Page 27] Internet Draft SNANAU APPN MIB April 1996 "Administratively assigned name for the port associated with this link station. The name can be from one to ten characters." ::= { appnLsEntry 4 } appnLsDlcType OBJECT-TYPE SYNTAX IANAifType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of DLC interface, distinguished according to the protocol immediately 'below' this layer." ::= { appnLsEntry 5 } appnLsDynamic OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies whether this is a dynamic link station. Dynamic link stations are created when links that have not been locally defined are established by adjacent nodes." ::= { appnLsEntry 6 } appnLsAdjCpName OBJECT-TYPE SYNTAX DisplayString (SIZE (0 | 3..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "Fully qualified name of the adjacent node for this link station. The name can be from three to seventeen characters. Format is NetId.CpName. The value of this object is determined as follows: 1. If the adjacent node's name was received on XID, it is returned. 2. If the adjacent node's name was not received on XID, but a locally-defined value is available, it is returned. 3. Otherwise a string of length 0 is returned, indicating Expires October 01, 1996 [Page 28] Internet Draft SNANAU APPN MIB April 1996 that no name is known for the adjacent node." ::= { appnLsEntry 7 } appnLsAdjNodeType OBJECT-TYPE SYNTAX INTEGER { networkNode(1), endNode(2), t21len(4), unknown(255) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the type of the adjacent node on this link." ::= { appnLsEntry 8 } appnLsTgNum OBJECT-TYPE SYNTAX INTEGER (0..256) MAX-ACCESS read-only STATUS current DESCRIPTION "Number associated with the TG to this link station, with a range from 0 to 256. A value of 256 indicates that the TG number has not been negotiated and is unknown at this time." ::= { appnLsEntry 9 } appnLsLimResource OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the link station is a limited resource. A link station that is a limited resource is deactivated when it is no longer in use." ::= { appnLsEntry 10 } appnLsActOnDemand OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the link station is activatable on demand. Expires October 01, 1996 [Page 29] Internet Draft SNANAU APPN MIB April 1996 Such a link station is reported in the topology as active regardless of its actual state, so that it can be considered in route calculations. If the link station is inactive and is chosen for a route, it will be activated at that time." ::= { appnLsEntry 11 } appnLsMigration OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this link station will be used for connections to down-level or migration partners. In general, migration nodes do not append their CP names on XID3. Such nodes: (1) will not support parallel TGs, (2) should be sent ACTPU (provided that the partner supports ACTPUs), and (3) should not be sent segmented BINDs. However, if this node receives an XID3 with an appended CP name, then the partner node will not be treated as a migration node. In the case of DYNAMIC TGs this object should be set to 'no'." ::= { appnLsEntry 12 } appnLsPartnerNodeId OBJECT-TYPE SYNTAX DisplayString (SIZE (8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The partner's node_id consists of two parts: Block number of the partner node: The block number is the first three digits of the node_id. These 3 hexadecimal digits identify the product. The value is '000' when the partner node_id is not defined. ID number of the partner node: The ID number is the last 5 digits of the node_id. These 5 hexadecimal digits are administratively defined and combined with the 3-digit block number form the node_id. This node_id is used to identify the node in XIDs. A unique value is required for connections to SNA subarea. The value is '00000' when the partner node_id is not defined." Expires October 01, 1996 [Page 30] Internet Draft SNANAU APPN MIB April 1996 ::= { appnLsEntry 13 } appnLsCpCpSessionSupport OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether CP-CP sessions are supported by this link station. For a dynamic link, this object represents the default ('Admin') value." ::= { appnLsEntry 14 } appnLsMaxSendBtuSize OBJECT-TYPE SYNTAX INTEGER (99..32767) UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Numeric value between 99 and 32767 inclusive indicating the desired number of bytes in a Basic Transmission Unit (BTU) sent on this link. When the link is inactive or activating, the value configured at this node is returned. When the link is active, the value that was negotiated for it is returned. This negotiated value is the smaller of the value configured at this node and the partner's maximum receive BTU length, received in XID." ::= { appnLsEntry 15 } appnLsInXidBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of XID bytes received." ::= { appnLsEntry 16 } appnLsInMsgBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of message (I-frame) bytes received." Expires October 01, 1996 [Page 31] Internet Draft SNANAU APPN MIB April 1996 ::= { appnLsEntry 17 } appnLsInXidFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of XID frames received." ::= { appnLsEntry 18 } appnLsInMsgFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of message (I-frame) frames received." ::= { appnLsEntry 19 } appnLsOutXidBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of XID bytes sent." ::= { appnLsEntry 20 } appnLsOutMsgBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of message (I-frame) bytes sent." ::= { appnLsEntry 21 } appnLsOutXidFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of XID frames sent." ::= { appnLsEntry 22 } Expires October 01, 1996 [Page 32] Internet Draft SNANAU APPN MIB April 1996 appnLsOutMsgFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of message (I-frame) frames sent." ::= { appnLsEntry 23 } appnLsEchoRsps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of responses returned from adjacent link station. A response should be returned for each test frame sent by this node. Test frames are sent to adjacent nodes periodically to verify connectivity and to measure the actual round trip time, that is, the time interval from when the test frame is sent until when the response is received." ::= { appnLsEntry 24 } appnLsCurrentDelay OBJECT-TYPE SYNTAX Integer32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The time that it took for the last test signal to be sent and returned from this link station to the adjacent link station. This time is represented in milliseconds." ::= { appnLsEntry 25 } appnLsMaxDelay OBJECT-TYPE SYNTAX Integer32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The longest time it took for a test signal to be sent and returned from this link station to the adjacent link station. This time is represented in milliseconds ." Expires October 01, 1996 [Page 33] Internet Draft SNANAU APPN MIB April 1996 ::= { appnLsEntry 26 } appnLsMinDelay OBJECT-TYPE SYNTAX Integer32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The shortest time it took for a test signal to be sent and returned from this link station to the adjacent link station. This time is represented in milliseconds." ::= { appnLsEntry 27 } appnLsMaxDelayTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time when the longest delay occurred. This time can be used to identify when this high water mark occurred in relation to other events in the agent, such as the last time the APPN node was re-initialized." ::= { appnLsEntry 28 } appnLsGoodXids OBJECT-TYPE SYNTAX Counter32 UNITS "XID exchanges" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of successful XID exchanges that have occurred on this link station since the time it was started." ::= { appnLsEntry 29 } appnLsBadXids OBJECT-TYPE SYNTAX Counter32 UNITS "XID exchanges" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of unsuccessful XID exchanges that have occurred on this link station since the time it was started." Expires October 01, 1996 [Page 34] Internet Draft SNANAU APPN MIB April 1996 ::= { appnLsEntry 30 } appnLsSpecific OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the object, e.g., one in a DLC-specific MIB, that can provide additional information related to this link station." ::= { appnLsEntry 31 } appnLsActiveTime OBJECT-TYPE SYNTAX TimeTicks UNITS "hundredths of a second" MAX-ACCESS read-only STATUS current DESCRIPTION "The cumulative amount of time since node activation, measured in hundredths of a second, that this link station has been in the active state. A zero value indicates that the link station has never been active." ::= { appnLsEntry 32 } appnLsCurrentStateTime OBJECT-TYPE SYNTAX TimeTicks UNITS "hundredths of a second" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time, measured in hundredths of a second, that the link station has been in its current state." ::= { appnLsEntry 33 } appnLsHprSup OBJECT-TYPE SYNTAX INTEGER { noHprSupport(1), hprBaseOnly(2), rtpTower(3), controlFlowsOverRtpTower(4) } MAX-ACCESS read-only STATUS current Expires October 01, 1996 [Page 35] Internet Draft SNANAU APPN MIB April 1996 DESCRIPTION "Indicates the level of high performance routing (HPR) support over this link. If the link is not active, the defined value will be returned." ::= { appnLsEntry 34 } appnLsErrRecoSup OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the link station is supporting HPR link-level error recovery or not." ::= { appnLsEntry 35 } appnLsForAnrLabel OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The forward ANR label for this link station. If the link does not support HPR or the value is unknown, a zero length string will be returned." ::= { appnLsEntry 36 } appnLsRevAnrLabel OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The reverse ANR label for this link station. If the link does not support HPR or the value is unknown, a zero length string will be returned." ::= { appnLsEntry 37 } appnLsCpCpNceId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The NCE ID for CP-CP sessions if this node supports HPR transport tower, a zero length string if the value Expires October 01, 1996 [Page 36] Internet Draft SNANAU APPN MIB April 1996 is unknown or not meaningful for this node." ::= { appnLsEntry 38 } appnLsRouteNceId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The NCE ID for Route Setup if this node supports the HPR transport tower, a zero length string if the value is unknown or not meaningful for this node." ::= { appnLsEntry 39 } appnLsBfNceId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The NCE ID for the APPN/HPR boundary function if this node supports the HPR transport tower, a zero length string if the value is unknown or not meaningful for this node." ::= { appnLsEntry 40 } appnLsLocalAddr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Local address, represented as a DisplayString. A zero-length string indicates that this value is unknown or not applicable." ::= { appnLsEntry 41 } appnLsRemoteAddr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Remote address, represented as a DisplayString. A zero-length string indicates that this value is unknown or not applicable." ::= { appnLsEntry 42 } Expires October 01, 1996 [Page 37] Internet Draft SNANAU APPN MIB April 1996 appnLsRemoteLsName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..10)) MAX-ACCESS read-only STATUS current DESCRIPTION "Remote link station discovered from the XID exchange. The name can be from one to ten characters. A zero-length string indicates that the value is not known." ::= { appnLsEntry 43 } --******************************************************************** -- This table provides information about errors this node encountered -- with connections to adjacent nodes. This includes all exceptional -- conditions encountered establishing connections and all exceptional -- conditions that resulted in termination of a connection. It is an -- implementation option how many entries to keep in this table, and -- how long to retain any individual entry. --******************************************************************** appnLsStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnLsStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information related to exceptional and potentially exceptional conditions that occurred during the activation, XID exchange, and termination of the connection." ::= { appnLinkStationInformation 2 } appnLsStatusEntry OBJECT-TYPE SYNTAX AppnLsStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by the LsStatusIndex, which is an integer that is continuously updated until it eventually wraps. This provides a Management Station with the ability to retrieve only the updates to the table, by using the standard GET NEXT." INDEX { appnLsStatusIndex } Expires October 01, 1996 [Page 38] Internet Draft SNANAU APPN MIB April 1996 ::= { appnLsStatusTable 1 } AppnLsStatusEntry ::= SEQUENCE { appnLsStatusIndex INTEGER, appnLsStatusTime DateAndTime, appnLsStatusLsName DisplayString, appnLsStatusCpName DisplayString, appnLsStatusPartnerId DisplayString, appnLsStatusTgNum INTEGER, appnLsStatusGeneralSense SnaSenseData, appnLsStatusRetry INTEGER, appnLsStatusEndSense SnaSenseData, appnLsStatusXidLocalSense SnaSenseData, appnLsStatusXidRemoteSense SnaSenseData, appnLsStatusXidByteInError INTEGER, appnLsStatusXidBitInError INTEGER, appnLsStatusDlcType IANAifType, appnLsStatusLocalAddr DisplayString, appnLsStatusRemoteAddr DisplayString } appnLsStatusIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table index. The value of the index begins at zero and is incremented up to a maximum value of 2**31-1 (2,147,483,647) before wrapping." ::= { appnLsStatusEntry 1 } appnLsStatusTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "Time when the exception condition occurred. This time can be used to identify when this event occurred in relation to other events in the agent, such as the last time the APPN node was re-initialized." ::= { appnLsStatusEntry 2 } appnLsStatusLsName OBJECT-TYPE Expires October 01, 1996 [Page 39] Internet Draft SNANAU APPN MIB April 1996 SYNTAX DisplayString (SIZE (1..10)) MAX-ACCESS read-only STATUS current DESCRIPTION "Administratively assigned name for the link station experiencing the condition." ::= { appnLsStatusEntry 3 } appnLsStatusCpName OBJECT-TYPE SYNTAX DisplayString (SIZE (0 | 3..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "Fully qualified name of the adjacent node for this link station. The name can be from three to seventeen characters. Format is NetId.CpName. The value of this object is determined as follows: 1. If the adjacent node's name was received on XID, it is returned. 2. If the adjacent node's name was not received on XID, but a locally-defined value is available, it is returned. 3. Otherwise a string of length 0 is returned, indicating that no name is known for the adjacent node." ::= { appnLsStatusEntry 4 } appnLsStatusPartnerId OBJECT-TYPE SYNTAX DisplayString (SIZE (8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The partner's node_id consists of two parts: Block number of the partner node: The block number is the first three digits of the node_id. These 3 hexadecimal digits identify the product. The value is '000' when the partner node_id is not defined. ID number of the partner node: The ID number is the last 5 digits of the node_id. These 5 hexadecimal digits are Expires October 01, 1996 [Page 40] Internet Draft SNANAU APPN MIB April 1996 administratively defined and combined with the 3-digit block number form the node_id. This node_id is used to identify the node in XIDs. A unique value is required for connections to SNA subarea. The value is '00000' when the partner node_id is not defined." ::= { appnLsStatusEntry 5 } appnLsStatusTgNum OBJECT-TYPE SYNTAX INTEGER (0..256) MAX-ACCESS read-only STATUS current DESCRIPTION "Number associated with the TG to this link station, with a range from 0 to 256. A value of 256 indicates that the TG number was unknown at the time of the failure." ::= { appnLsStatusEntry 6 } appnLsStatusGeneralSense OBJECT-TYPE SYNTAX SnaSenseData MAX-ACCESS read-only STATUS current DESCRIPTION "The error sense data associated with the start sequence of activation of a link up to the beginning of the XID sequence. This is the sense data that came from CS whenever the link did not activate or when it went inactive." ::= { appnLsStatusEntry 7 } appnLsStatusRetry OBJECT-TYPE SYNTAX INTEGER { retry(1), noRetry(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the node will retry the start request to activate the link." ::= { appnLsStatusEntry 8 } appnLsStatusEndSense OBJECT-TYPE Expires October 01, 1996 [Page 41] Internet Draft SNANAU APPN MIB April 1996 SYNTAX SnaSenseData MAX-ACCESS read-only STATUS current DESCRIPTION "The sense data associated with the termination of the link connection to adjacent node. This is the sense data that came from the DLC layer." ::= { appnLsStatusEntry 9 } appnLsStatusXidLocalSense OBJECT-TYPE SYNTAX SnaSenseData MAX-ACCESS read-only STATUS current DESCRIPTION "The sense data associated with the rejection of the XID. This is the sense data that came from the local node (this node) when it built the CV22 to send to the remote node." ::= { appnLsStatusEntry 10 } appnLsStatusXidRemoteSense OBJECT-TYPE SYNTAX SnaSenseData MAX-ACCESS read-only STATUS current DESCRIPTION "The sense data the adjacent node returned to this node indicating the reason the XID was rejected. This is the sense data that came from the remote node in the CV22 it sent to the local node (this node)." ::= { appnLsStatusEntry 11 } appnLsStatusXidByteInError OBJECT-TYPE SYNTAX INTEGER (0..65536) MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the actual byte in the XID that caused the error. The value 65536 indicates that the object has no meaning. For values in the range 0-65535, this object corresponds to Expires October 01, 1996 [Page 42] Internet Draft SNANAU APPN MIB April 1996 bytes 2-3 of the XID Negotiation (X'22') control vector." ::= { appnLsStatusEntry 12 } appnLsStatusXidBitInError OBJECT-TYPE SYNTAX INTEGER (0..8) MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the actual bit in error (0 through 7) within the errored byte of the XID. The value 8 indicates that this object has no meaning. For values in the range 0-7, this object corresponds to byte 4 of the XID Negotiation (X'22') control vector." ::= { appnLsStatusEntry 13 } appnLsStatusDlcType OBJECT-TYPE SYNTAX IANAifType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of DLC interface, distinguished according to the protocol immediately 'below' this layer." ::= { appnLsStatusEntry 14 } appnLsStatusLocalAddr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Local address, represented as a DisplayString." ::= { appnLsStatusEntry 15 } appnLsStatusRemoteAddr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Remote address, represented as a DisplayString." ::= { appnLsStatusEntry 16 } Expires October 01, 1996 [Page 43] Internet Draft SNANAU APPN MIB April 1996 -- ********************************************************************* -- APPN Virtual Routing Node Information -- appnVrnTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnVrnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table relates a virtual routing node to an APPN port." ::= { appnVrnInfo 1 } appnVrnEntry OBJECT-TYPE SYNTAX AppnVrnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by the virtual routing node name, TG number, and port name. There will be a matching entry in the appnLocalTgTable to represent status and characteristics of the TG representing each virtual routing node definition." INDEX { appnVrnName, appnVrnTgNum, appnVrnPortName } ::= { appnVrnTable 1 } AppnVrnEntry ::= SEQUENCE { appnVrnName DisplayString, appnVrnTgNum INTEGER, appnVrnPortName DisplayString } appnVrnName OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Administratively assigned name of the virtual routing node. This is a fully qualified name, and matches the appnLocalTgDest name in the appnLocalTgTable." ::= { appnVrnEntry 1 } appnVrnTgNum OBJECT-TYPE Expires October 01, 1996 [Page 44] Internet Draft SNANAU APPN MIB April 1996 SYNTAX INTEGER(0..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Number associated with the transmission group representing this virtual routing node definition." ::= { appnVrnEntry 2 } appnVrnPortName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..10)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the port this virtual routing node definition is defined to." ::= { appnVrnEntry 3 } -- ************** The APPN Topology Group ****************************** appnNn OBJECT IDENTIFIER ::= { appnObjects 2 } appnNnTopo OBJECT IDENTIFIER ::= { appnNn 1 } appnNnTopology OBJECT IDENTIFIER ::= { appnNn 2 } -- This group is used to represent the entire APPN network-node topology -- including network nodes, virtual routing nodes and all TGs associated -- with these nodes. -- -- Network nodes -- The APPN topology database consists of information about every APPN -- network node in this network node's topology subnetwork. This -- information is learned over time as each network node exchanges -- topology information with the network nodes adjacent to it. The -- database consists of information about each node, and information -- about all of the transmission groups used by these nodes. -- -- Virtual routing nodes -- Information about virtual routing nodes (representing connection -- networks) is treated in the same way as information about network -- nodes, and is replicated at each network node. For a virtual routing -- node, the node name is the only meaningful information. The other -- node objects use default values. Each node that has defined -- a TG with this virtual routing node as the destination also defines a Expires October 01, 1996 [Page 45] Internet Draft SNANAU APPN MIB April 1996 -- TG on this virtual routing node. There is a TG record for each node -- that uses this virtual routing node. -- -- The APPN node table represents node information from the APPN topology -- database, with the Flow Reduction Sequence Number (FRSN) and APPN CP -- fully qualified name serving as the index. The FRSN is the agent's -- relative time stamp of an update to the network topology database. -- After collecting the entire database once, a management application -- can montior the 'appnNnFrsn' objects to detect a change in the -- database, and retrieve only updates using GET NEXT commands -- starting from the last retrieved node and TG entries. -- -- The format of the actual APPN topology database is as follows: -- -- Node table (entry for each node in network) -- TG table (entry for each TG owned by node) -- -- Due to SNMP's ASN.1 limitations, we cannot represent the TG table -- within the node table in this way. We define separate tables for -- nodes and TGs, adding the node name to each TG entry to provide a -- means of correlating the TG with its originating node. appnNnTopoMaxNodes OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of node entries allowed in the APPN topology database. It is an implementation choice whether to count only network-node entries, or to count all node entries. If the number of node entries exceeds this value, APPN will issue an Alert and the node can no longer participate as a network node. The value 0 indicates that the local node has no defined limit, and the number of node entries is bounded only by memory." ::= { appnNnTopo 1 } appnNnTopoCurNumNodes OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current number of node entries in this node's topology database. It is an implementation choice whether to count only network-node entries, or to count all node entries. If this value exceeds the maximum number of nodes allowed Expires October 01, 1996 [Page 46] Internet Draft SNANAU APPN MIB April 1996 (appnNnTopoMaxNodes, if that field in not 0), APPN Alert CPDB002 is issued." ::= { appnNnTopo 2 } appnNnTopoNodePurges OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of topology node records purged from this node's topology database since the node was last re-initialized." ::= { appnNnTopo 3 } appnNnTopoTgPurges OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of topology TG records purged from this node's topology database since the node was last re-initialized." ::= { appnNnTopo 4 } appnNnTopoTotalTduWars OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of TDU wars detected by this node since its last initialization." ::= { appnNnTopo 5 } -- APPN network node topology table (using FRSN as index) -- This table describes every APPN network node and virtual routing node -- represented in this node's topology database. appnNnTopologyFRTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnNnTopologyFREntry MAX-ACCESS not-accessible STATUS current Expires October 01, 1996 [Page 47] Internet Draft SNANAU APPN MIB April 1996 DESCRIPTION "Portion of the APPN topology database that describes all of the APPN network nodes and virtual routing nodes known to this node." ::= { appnNnTopology 3 } appnNnTopologyFREntry OBJECT-TYPE SYNTAX AppnNnTopologyFREntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The FRSN and the fully qualified node name are used to index this table." INDEX {appnNnNodeFRFrsn, appnNnNodeFRName} ::= { appnNnTopologyFRTable 1 } AppnNnTopologyFREntry ::= SEQUENCE { appnNnNodeFRFrsn Integer32, appnNnNodeFRName DisplayString, appnNnNodeFREntryTimeLeft INTEGER, appnNnNodeFRType INTEGER, appnNnNodeFRRsn Integer32, appnNnNodeFRRouteAddResist INTEGER, appnNnNodeFRCongested INTEGER, appnNnNodeFRIsrDepleted INTEGER, appnNnNodeFRQuiescing INTEGER, appnNnNodeFRGateway INTEGER, appnNnNodeFRCentralDirectory INTEGER, appnNnNodeFRIsr INTEGER, appnNnNodeFRGarbageCollect INTEGER, appnNnNodeFRHprSupport INTEGER, appnNnNodeFRPeriBorderSup INTEGER, appnNnNodeFRInterchangeSup INTEGER, appnNnNodeFRExteBorderSup INTEGER } appnNnNodeFRFrsn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible Expires October 01, 1996 [Page 48] Internet Draft SNANAU APPN MIB April 1996 STATUS current DESCRIPTION "Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last relative time this resource was updated at the agent node." ::= { appnNnTopologyFREntry 1 } appnNnNodeFRName OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Administratively assigned network name that is locally defined at each network node in the format NetId.CpName." ::= { appnNnTopologyFREntry 2 } appnNnNodeFREntryTimeLeft OBJECT-TYPE SYNTAX INTEGER (0..15) UNITS "days" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of days before deletion of this network node entry. Range is 0-15. 0 indicates this entry will be deleted in this or the next garbage collection cycle." ::= { appnNnTopologyFREntry 3 } appnNnNodeFRType OBJECT-TYPE SYNTAX INTEGER { networkNode(1), virtualRoutingNode(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of APPN node." ::= { appnNnTopologyFREntry 4 } appnNnNodeFRRsn OBJECT-TYPE SYNTAX Integer32 Expires October 01, 1996 [Page 49] Internet Draft SNANAU APPN MIB April 1996 MAX-ACCESS read-only STATUS current DESCRIPTION "Resource sequence number, which is assigned and controlled by the network node that owns this resource. An odd number indicates that information about the resource is inconsistent. This object corresponds to cv4580, bytes 2-5." ::= { appnNnTopologyFREntry 5 } appnNnNodeFRRouteAddResist OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Route addition resistance. This administratively assigned value indicates the relative desirability of using this node for intermediate session traffic. The value, which can be any integer 0-255, is used in route computation. The lower the value, the more desirable the node is for intermediate routing. This object corresponds to cv4580, byte 6." ::= { appnNnTopologyFREntry 6 } appnNnNodeFRCongested OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this node is congested. This node is not be included in route selection by other nodes when this congestion exists. This object corresponds to cv4580, byte 7, bit 0." ::= { appnNnTopologyFREntry 7 } appnNnNodeFRIsrDepleted OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION Expires October 01, 1996 [Page 50] Internet Draft SNANAU APPN MIB April 1996 "Indicates whether intermediate session routing resources are depleted. This node is not included in intermediate route selection by other nodes when resources are depleted. This object corresponds to cv4580, byte 7, bit 1." ::= { appnNnTopologyFREntry 8 } appnNnNodeFRQuiescing OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the node is quiescing. This node is not included in route selection by other nodes when the node is quiescing. This object corresponds to cv4580, byte 7, bit 5." ::= { appnNnTopologyFREntry 9 } appnNnNodeFRGateway OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the node provide gateway services. This object corresponds to cv4580, byte 8, bit 0." ::= { appnNnTopologyFREntry 10 } appnNnNodeFRCentralDirectory OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the node supports central directory services. This object corresponds to cv4580, byte 8, bit 1." ::= { appnNnTopologyFREntry 11 } Expires October 01, 1996 [Page 51] Internet Draft SNANAU APPN MIB April 1996 appnNnNodeFRIsr OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the node supports intermediate session routing (ISR). This object corresponds to cv4580, byte 8, bit 2." ::= { appnNnTopologyFREntry 12 } appnNnNodeFRGarbageCollect OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the node has been marked for garbage collection (deletion from the topology database) upon the next garbage collection cycle. This object corresponds to cv4580, byte 7, bit 3." ::= { appnNnTopologyFREntry 13 } appnNnNodeFRHprSupport OBJECT-TYPE SYNTAX INTEGER { noHprSupport(1), hprBaseOnly(2), rtpTower(3), controlFlowsOverRtpTower(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates this node's level of support for high performance routing (HPR). This object corresponds to cv4580, byte 9, bits 3-4." ::= { appnNnTopologyFREntry 14 } appnNnNodeFRPeriBorderSup OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current Expires October 01, 1996 [Page 52] Internet Draft SNANAU APPN MIB April 1996 DESCRIPTION "Indicates whether this node has peripheral border node support. This object corresponds to cv4580, byte 9, bit 0." ::= { appnNnTopologyFREntry 15 } appnNnNodeFRInterchangeSup OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this node has interchange node support. This object corresponds to cv4580, byte 9, bit 1." ::= { appnNnTopologyFREntry 16 } appnNnNodeFRExteBorderSup OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this node has extended border node support. This object corresponds to cv4580, byte 9, bit 2." ::= { appnNnTopologyFREntry 17 } --APPN transmission group (TG) table -- This table describes the TGs associated with all the APPN network -- nodes known to this node. The originating (owning) node for each -- TG is repeated here to provide a means of correlating the TGs with -- the nodes. appnNnTgTopologyFRTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnNnTgTopologyFREntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Portion of the APPN topology database that describes all of Expires October 01, 1996 [Page 53] Internet Draft SNANAU APPN MIB April 1996 the APPN transmissions groups between nodes in the database." ::= { appnNnTopology 4 } appnNnTgTopologyFREntry OBJECT-TYPE SYNTAX AppnNnTgTopologyFREntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by four columns: FRSN, TG owner fully qualified node name, TG destination fully qualified node name, and TG number." INDEX {appnNnTgFRFrsn, appnNnTgFROwner, appnNnTgFRDest, appnNnTgFRNum} ::= { appnNnTgTopologyFRTable 1 } AppnNnTgTopologyFREntry ::= SEQUENCE { appnNnTgFRFrsn Integer32, appnNnTgFROwner DisplayString, appnNnTgFRDest DisplayString, appnNnTgFRNum INTEGER, appnNnTgFREntryTimeLeft INTEGER, appnNnTgFRDestVirtual INTEGER, appnNnTgFRDlcData OCTET STRING, appnNnTgFRRsn Integer32, appnNnTgFROperational INTEGER, appnNnTgFRQuiescing INTEGER, appnNnTgFRCpCpSession INTEGER, appnNnTgFREffCap OCTET STRING, appnNnTgFRConnCost INTEGER, appnNnTgFRByteCost INTEGER, appnNnTgFRSecurity INTEGER, appnNnTgFRDelay OCTET STRING, appnNnTgFRUsr1 INTEGER, appnNnTgFRUsr2 INTEGER, appnNnTgFRUsr3 INTEGER, appnNnTgFRGarbageCollect INTEGER, appnNnTgFRSubareaNum Integer32, Expires October 01, 1996 [Page 54] Internet Draft SNANAU APPN MIB April 1996 appnNnTgFRHprSup INTEGER, appnNnTgFRDestHprTrans INTEGER, appnNnTgFRTypeIndicator INTEGER, appnNnTgFRIntersubnet INTEGER } appnNnTgFRFrsn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last time this resource was updated at this node." ::= { appnNnTgTopologyFREntry 1 } appnNnTgFROwner OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Administratively assigned name for the originating node for this TG. The format is NetId.CpName and is the same name specified in the node table." ::= { appnNnTgTopologyFREntry 2 } appnNnTgFRDest OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Administratively assigned fully qualified network name for the destination node for this TG." ::= { appnNnTgTopologyFREntry 3 } appnNnTgFRNum OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION Expires October 01, 1996 [Page 55] Internet Draft SNANAU APPN MIB April 1996 "Number associated with this transmission group. Range is 0-255." ::= { appnNnTgTopologyFREntry 4 } appnNnTgFREntryTimeLeft OBJECT-TYPE SYNTAX INTEGER (0..15) UNITS "days" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of days before deletion of this network node TG entry if it is not operational or has an odd (inconsistent) RSN. Range is 0-15." ::= { appnNnTgTopologyFREntry 5 } appnNnTgFRDestVirtual OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the destination node is a virtual routing node." ::= { appnNnTgTopologyFREntry 6 } appnNnTgFRDlcData OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "DLC specific data related to the link connection network. Examples: Token-Ring - MAC/SAP X.25 Switched - dial digits X.21 Switched - dial digits Circuit Switch - dial digits" ::= { appnNnTgTopologyFREntry 7 } appnNnTgFRRsn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current Expires October 01, 1996 [Page 56] Internet Draft SNANAU APPN MIB April 1996 DESCRIPTION "Current owning node's resource sequence number for this resource. An odd number indicates that information about the resource is inconsistent. This object corresponds to cv47, bytes 2-5" ::= { appnNnTgTopologyFREntry 8 } appnNnTgFROperational OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the transmission group is operational. This object corresponds to cv47, byte 6, bit 0." ::= { appnNnTgTopologyFREntry 9 } appnNnTgFRQuiescing OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the transmission group is quiescing. This object corresponds to cv47, byte 6, bit 2." ::= { appnNnTgTopologyFREntry 10 } appnNnTgFRCpCpSession OBJECT-TYPE SYNTAX INTEGER { supportedUnknownStatus(1), supportedActive(2), notSupported(3), supportedNotActive(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether CP-CP sessions are supported and active on this TG. Some nodes in the network are not able to differentiate support and status of CP-CP sessions, and thus may report the 'supportedUnknownStatus' value. Expires October 01, 1996 [Page 57] Internet Draft SNANAU APPN MIB April 1996 This object corresponds to cv47, byte 6, bits 3-4." ::= { appnNnTgTopologyFREntry 11 } appnNnTgFREffCap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-only STATUS current DESCRIPTION "Effective capacity for this TG. This is an administratively assigned value derived from the link bandwidth and maximum load factor. It is encoded in the same way as byte 7 of cv47, and represents a floating-point number in units of 300 bits per second." ::= { appnNnTgTopologyFREntry 12 } appnNnTgFRConnCost OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Cost per connect time. This is an administratively assigned value representing the relative cost per unit of time to use this TG. Range is from 0, which means no cost, to 255, which indicates maximum cost. This object corresponds to cv47, byte 13." ::= { appnNnTgTopologyFREntry 13 } appnNnTgFRByteCost OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Cost per connect time. This is an administratively assigned value representing the relative cost of transmitting a byte over this TG. Range is from 0, which means no cost, to 255, which indicates maximum cost. Expires October 01, 1996 [Page 58] Internet Draft SNANAU APPN MIB April 1996 This object corresponds to cv47, byte 14." ::= { appnNnTgTopologyFREntry 14 } appnNnTgFRSecurity OBJECT-TYPE SYNTAX INTEGER { nonsecure(1), -- X'01' publicSwitchedNetwork(32), -- X'20' undergroundCable(64), -- X'40' secureConduit(96), -- X'60' guardedConduit(128), -- X'80' encrypted(160), -- X'A0' guardedRadiation(192) -- X'C0' } MAX-ACCESS read-only STATUS current DESCRIPTION "Administratively assigned security level of this TG. If a network needs security values other than the architecturally defined ones listed here, one of the three user-defined characteristics may be used to specify the required additional security values. This object corresponds to cv47, byte 16." ::= { appnNnTgTopologyFREntry 15 } appnNnTgFRDelay OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-only STATUS current DESCRIPTION "Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in microseconds, using the same encoding scheme used in cv47 in a topology update. Some of the more common values, along with their encoded hex values, are: minimum(0), X'00' negligible(384), X'4C' terrestrial(9216), X'71' packet(147456), X'91' long(294912), X'99' maximum(2013265920) X'FF' Expires October 01, 1996 [Page 59] Internet Draft SNANAU APPN MIB April 1996 This is an administratively assigned value associated with this TG. This object corresponds to cv47, byte 17." ::= { appnNnTgTopologyFREntry 16 } appnNnTgFRUsr1 OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "First user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG. This object corresponds to cv47, byte 19." ::= { appnNnTgTopologyFREntry 17 } appnNnTgFRUsr2 OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Second user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG. This object corresponds to cv47, byte 20." ::= { appnNnTgTopologyFREntry 18 } appnNnTgFRUsr3 OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Third user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG. This object corresponds to cv47, byte 21." ::= { appnNnTgTopologyFREntry 19 } appnNnTgFRGarbageCollect OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only Expires October 01, 1996 [Page 60] Internet Draft SNANAU APPN MIB April 1996 STATUS current DESCRIPTION "Indicates whether the TG has been marked for garbage collection (deletion from the topology database) upon the next garbage collection cycle. This object corresponds to cv47, byte 6, bit 1." ::= { appnNnTgTopologyFREntry 20 } appnNnTgFRSubareaNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The subarea number associated with this TG. This object corresponds to cv4680, bytes m+2 through m+5." ::= { appnNnTgTopologyFREntry 21 } appnNnTgFRHprSup OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether or not high performance routing (HPR) is supported over this TG. This object corresponds to cv4680, byte m+1, bit 2." ::= { appnNnTgTopologyFREntry 22 } appnNnTgFRDestHprTrans OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the destination node supports high performance routing (HPR) transport tower. This object corresponds to cv4680, byte m+1, bit 7." ::= { appnNnTgTopologyFREntry 23 } appnNnTgFRTypeIndicator OBJECT-TYPE Expires October 01, 1996 [Page 61] Internet Draft SNANAU APPN MIB April 1996 SYNTAX INTEGER { unknown(1), appnOrBfTg(2), interchangeTg(3), virtualRouteTg(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the type of the TG. This object corresponds to cv4680, byte m+1, bits 3-4." ::= { appnNnTgTopologyFREntry 24 } appnNnTgFRIntersubnet OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the transmission group is an intersubnet link, which defines a border between subnetworks. This object corresponds to cv4680, byte m+1, bit 5." ::= { appnNnTgTopologyFREntry 25 } -- ************** The APPN Local Topology Group ************************ -- This MIB Group represents the local topology maintained in -- both APPN end nodes and network nodes. It consists of two -- tables: -- - a table containing information about all of the TGs owned -- by this node, which is implemented by all node types. -- - a table containing all of the information known to this node -- about the TGs owned by its end nodes, which is implemented only -- by network nodes. appnLocalTopology OBJECT IDENTIFIER ::= { appnObjects 3 } -- APPN Local Transmission Group (TG) table -- This table describes the TGs associated with this node only. appnLocalTgTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnLocalTgEntry MAX-ACCESS not-accessible STATUS current Expires October 01, 1996 [Page 62] Internet Draft SNANAU APPN MIB April 1996 DESCRIPTION "TG Table describes all of the TGs owned by this node. The TG destination can be a virtual node, network node, LEN node, or end node." ::= { appnLocalTopology 1 } appnLocalTgEntry OBJECT-TYPE SYNTAX AppnLocalTgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by the destination CPname and the TG number." INDEX {appnLocalTgDest, appnLocalTgNum} ::= { appnLocalTgTable 1 } AppnLocalTgEntry ::= SEQUENCE { appnLocalTgDest DisplayString, appnLocalTgNum INTEGER, appnLocalTgDestVirtual INTEGER, appnLocalTgDlcData OCTET STRING, appnLocalTgPortName DisplayString, appnLocalTgQuiescing INTEGER, appnLocalTgOperational INTEGER, appnLocalTgCpCpSession INTEGER, appnLocalTgEffCap OCTET STRING, appnLocalTgConnCost INTEGER, appnLocalTgByteCost INTEGER, appnLocalTgSecurity INTEGER, appnLocalTgDelay OCTET STRING, appnLocalTgUsr1 INTEGER, appnLocalTgUsr2 INTEGER, appnLocalTgUsr3 INTEGER, appnLocalTgHprSup INTEGER, appnLocalTgIntersubnet INTEGER } appnLocalTgDest OBJECT-TYPE Expires October 01, 1996 [Page 63] Internet Draft SNANAU APPN MIB April 1996 SYNTAX DisplayString (SIZE (3..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Administratively assigned name of the destination node for this TG. This is the fully qualified name of a network node, end node, LEN node, or virtual routing node." ::= { appnLocalTgEntry 1 } appnLocalTgNum OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Number associated with this transmission group." ::= { appnLocalTgEntry 2 } appnLocalTgDestVirtual OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the destination node for this TG is a virtual routing node." ::= { appnLocalTgEntry 3 } appnLocalTgDlcData OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "DLC-specific data related to the link connection network. Examples: Token-Ring - MAC/SAP X.25 Switched - dial digits X.21 Switched - dial digits Circuit Switch - dial digits" ::= { appnLocalTgEntry 4 } appnLocalTgPortName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..10)) Expires October 01, 1996 [Page 64] Internet Draft SNANAU APPN MIB April 1996 MAX-ACCESS read-only STATUS current DESCRIPTION "Administratively assigned name for the local port associated with this TG. A zero-length string indicates that this value is unknown." ::= { appnLocalTgEntry 5 } appnLocalTgQuiescing OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the transmission group is quiescing." ::= { appnLocalTgEntry 6 } appnLocalTgOperational OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the transmission group is operational." ::= { appnLocalTgEntry 7 } appnLocalTgCpCpSession OBJECT-TYPE SYNTAX INTEGER { supportedUnknownStatus(1), supportedActive(2), notSupported(3), supportedNotActive(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether CP-CP sessions are supported and active on this TG. Some nodes in the network are not able to differentiate support and status of CP-CP sessions, and thus may report the 'supportedUnknownStatus' value." ::= { appnLocalTgEntry 8 } appnLocalTgEffCap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) Expires October 01, 1996 [Page 65] Internet Draft SNANAU APPN MIB April 1996 MAX-ACCESS read-only STATUS current DESCRIPTION "Effective capacity for this TG. This is an administratively assigned value derived from the link bandwidth and maximum load factor. It is encoded in the same way as byte 7 of cv47, and represents a floating-point number in units of 300 bits per second." ::= { appnLocalTgEntry 9 } appnLocalTgConnCost OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255." ::= { appnLocalTgEntry 10 } appnLocalTgByteCost OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Relative cost of transmitting a byte over this link. Range is from 0 (lowest cost) to 255." ::= { appnLocalTgEntry 11 } appnLocalTgSecurity OBJECT-TYPE SYNTAX INTEGER { nonsecure(1), -- X'01' publicSwitchedNetwork(32), -- X'20' undergroundCable(64), -- X'40' secureConduit(96), -- X'60' guardedConduit(128), -- X'80' encrypted(160), -- X'A0' guardedRadiation(192) -- X'C0' } MAX-ACCESS read-only STATUS current DESCRIPTION Expires October 01, 1996 [Page 66] Internet Draft SNANAU APPN MIB April 1996 "Administratively assigned security level of this TG. If a network needs security values other than the architecturally defined ones listed here, one of the three user-defined characteristics may be used to specify the required additional security values." ::= { appnLocalTgEntry 12 } appnLocalTgDelay OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-only STATUS current DESCRIPTION "Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in microseconds, using the same encoding scheme used in cv47 in a topology update. Some of the more common values, along with their encoded hex values, are: minimum(0), X'00' negligible(384), X'4C' terrestrial(9216), X'71' packet(147456), X'91' long(294912), X'99' maximum(2013265920) X'FF' This is an administratively assigned value associated with this TG. This object corresponds to cv47, byte 17." ::= { appnLocalTgEntry 13 } appnLocalTgUsr1 OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "First user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG." ::= { appnLocalTgEntry 14 } appnLocalTgUsr2 OBJECT-TYPE SYNTAX INTEGER (0..255) Expires October 01, 1996 [Page 67] Internet Draft SNANAU APPN MIB April 1996 MAX-ACCESS read-only STATUS current DESCRIPTION "Second user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG." ::= { appnLocalTgEntry 15 } appnLocalTgUsr3 OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Third user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG." ::= { appnLocalTgEntry 16 } appnLocalTgHprSup OBJECT-TYPE SYNTAX INTEGER { noHprSupport(1), hprBaseOnly(2), rtpTower(3), controlFlowsOverRtpTower(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the level of high performance routing (HPR) support over this TG ." ::= { appnLocalTgEntry 17 } appnLocalTgIntersubnet OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the transmission group is an intersubnet link (defines a border between subnetworks)." ::= { appnLocalTgEntry 18 } -- APPN Local End Node Transmission Group (TG) table -- This table describes the TGs associated with all of the end nodes Expires October 01, 1996 [Page 68] Internet Draft SNANAU APPN MIB April 1996 -- known to this node. appnLocalEnTgTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnLocalEnTgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table describing all of the TGs owned by the end nodes known to this node via TG registration. This node does not represent its own view of the TG on behalf of the partner node in this table. The TG destination can be a virtual routing node, network node, or end node." ::= { appnLocalTopology 2 } appnLocalEnTgEntry OBJECT-TYPE SYNTAX AppnLocalEnTgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table requires multiple indexes to uniquely identify each TG. They are originating CPname, destination CPname, and the TG number." INDEX {appnLocalEnTgOrigin, appnLocalEnTgDest, appnLocalEnTgNum} ::= { appnLocalEnTgTable 1 } AppnLocalEnTgEntry ::= SEQUENCE { appnLocalEnTgOrigin DisplayString, appnLocalEnTgDest DisplayString, appnLocalEnTgNum INTEGER, appnLocalEnTgEntryTimeLeft INTEGER, appnLocalEnTgDestVirtual INTEGER, appnLocalEnTgDlcData OCTET STRING, appnLocalEnTgOperational INTEGER, appnLocalEnTgCpCpSession INTEGER, appnLocalEnTgEffCap OCTET STRING, appnLocalEnTgConnCost INTEGER, appnLocalEnTgByteCost INTEGER, appnLocalEnTgSecurity INTEGER, Expires October 01, 1996 [Page 69] Internet Draft SNANAU APPN MIB April 1996 appnLocalEnTgDelay OCTET STRING, appnLocalEnTgUsr1 INTEGER, appnLocalEnTgUsr2 INTEGER, appnLocalEnTgUsr3 INTEGER } appnLocalEnTgOrigin OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Administratively assigned name of the origin node for this TG. This is a fully qualified network name." ::= { appnLocalEnTgEntry 1 } appnLocalEnTgDest OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Administratively assigned name of the destination node for this TG. This is the fully qualified name of a network node, end node, LEN node, or virtual routing node." ::= { appnLocalEnTgEntry 2 } appnLocalEnTgNum OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Number associated with this transmission group." ::= { appnLocalEnTgEntry 3 } appnLocalEnTgEntryTimeLeft OBJECT-TYPE SYNTAX INTEGER (0..15) UNITS "days" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of days before deletion of this end node TG entry. Range is 0-15." ::= { appnLocalEnTgEntry 4 } Expires October 01, 1996 [Page 70] Internet Draft SNANAU APPN MIB April 1996 appnLocalEnTgDestVirtual OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the destination node is a virtual routing node." ::= { appnLocalEnTgEntry 5 } appnLocalEnTgDlcData OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "DLC-specific data related to the link connection network. Examples: Token-Ring - MAC/SAP X.25 Switched - dial digits X.21 Switched - dial digits Circuit Switch - dial digits" ::= { appnLocalEnTgEntry 6 } appnLocalEnTgOperational OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the transmission group is operational." ::= { appnLocalEnTgEntry 7 } appnLocalEnTgCpCpSession OBJECT-TYPE SYNTAX INTEGER { supportedUnknownStatus(1), supportedActive(2), notSupported(3), supportedNotActive(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether CP-CP sessions are supported and active on this TG. Some nodes in the network are not able to Expires October 01, 1996 [Page 71] Internet Draft SNANAU APPN MIB April 1996 differentiate support and status of CP-CP sessions, and thus may report the 'supportedUnknownStatus' value." ::= { appnLocalEnTgEntry 8 } appnLocalEnTgEffCap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-only STATUS current DESCRIPTION "Effective capacity for this TG. This is an administratively assigned value derived from the link bandwidth and maximum load factor. It is encoded in the same way as byte 7 of cv47, and represents a floating-point number in units of 300 bits per second." ::= { appnLocalEnTgEntry 9 } appnLocalEnTgConnCost OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255." ::= { appnLocalEnTgEntry 10 } appnLocalEnTgByteCost OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Relative cost of transmitting a byte over this link. Range is from 0, which means no cost, to 255." ::= { appnLocalEnTgEntry 11 } appnLocalEnTgSecurity OBJECT-TYPE SYNTAX INTEGER { nonsecure(1), -- X'01' publicSwitchedNetwork(32), -- X'20' undergroundCable(64), -- X'40' secureConduit(96), -- X'60' Expires October 01, 1996 [Page 72] Internet Draft SNANAU APPN MIB April 1996 guardedConduit(128), -- X'80' encrypted(160), -- X'A0' guardedRadiation(192) -- X'C0' } MAX-ACCESS read-only STATUS current DESCRIPTION "Administratively assigned security level of this TG. If a network needs security values other than the architecturally defined ones listed here, one of the three user-defined characteristics may be used to specify the required additional security values." ::= { appnLocalEnTgEntry 12 } appnLocalEnTgDelay OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-only STATUS current DESCRIPTION "Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in microseconds, using the same encoding scheme used in cv47 in a topology update. Some of the more common values, along with their encoded hex values, are: minimum(0), X'00' negligible(384), X'4C' terrestrial(9216), X'71' packet(147456), X'91' long(294912), X'99' maximum(2013265920) X'FF' This is an administratively assigned value associated with this TG. This object corresponds to cv47, byte 17." ::= { appnLocalEnTgEntry 13 } appnLocalEnTgUsr1 OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION Expires October 01, 1996 [Page 73] Internet Draft SNANAU APPN MIB April 1996 "First user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG." ::= { appnLocalEnTgEntry 14 } appnLocalEnTgUsr2 OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Second user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG." ::= { appnLocalEnTgEntry 15 } appnLocalEnTgUsr3 OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Third user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG." ::= { appnLocalEnTgEntry 16 } -- ************** The APPN Directory Group ***************************** appnDir OBJECT IDENTIFIER ::= { appnObjects 4 } appnDirPerf OBJECT IDENTIFIER ::= { appnDir 1 } -- The APPN Directory Group -- The APPN Directory Database -- Each APPN network node maintains directories containing information on -- which LUs (applications) are available and where they are located. -- LUs can be located in an APPN network node or in any of its attached -- end nodes. appnDirMaxCaches OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of cache entries allowed. This is an administratively assigned value." Expires October 01, 1996 [Page 74] Internet Draft SNANAU APPN MIB April 1996 ::= { appnDirPerf 1 } appnDirCurCaches OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current number of cache entries." ::= { appnDirPerf 2 } appnDirCurHomeEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current number of home entries." ::= { appnDirPerf 3 } appnDirRegEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current number of registered entries." ::= { appnDirPerf 4 } appnDirInLocates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of directed Locates received since the node was last re-initialized." ::= { appnDirPerf 5 } appnDirInBcastLocates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of broadcast Locates received since the node was last re-initialized." Expires October 01, 1996 [Page 75] Internet Draft SNANAU APPN MIB April 1996 ::= { appnDirPerf 6 } appnDirOutLocates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of directed Locates sent since the node was last re-initialized." ::= { appnDirPerf 7 } appnDirOutBcastLocates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of broadcast Locates sent since the node was last re-initialized." ::= { appnDirPerf 8 } appnDirNotFoundLocates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of directed Locates returned with a 'not found' since the node was last re-initialized." ::= { appnDirPerf 9 } appnDirNotFoundBcastLocates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of broadcast Locates returned with a 'not found' since the node was last re-initialized." ::= { appnDirPerf 10 } appnDirLocateOutstands OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current Expires October 01, 1996 [Page 76] Internet Draft SNANAU APPN MIB April 1996 DESCRIPTION "Current number of outstanding Locates, both directed and broadcast. This value varies. A value of zero indicates that no Locates are unanswered." ::= { appnDirPerf 11 } --APPN Directory table -- This table contains information about all known LUs. appnDirTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnDirEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing information about all known LUs." ::= { appnDir 2 } appnDirEntry OBJECT-TYPE SYNTAX AppnDirEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by the LU name." INDEX {appnDirLuName} ::= { appnDirTable 1 } AppnDirEntry ::= SEQUENCE { appnDirLuName DisplayString, appnDirNnServerName DisplayString, appnDirLuOwnerName DisplayString, appnDirLuLocation INTEGER, appnDirType INTEGER } appnDirLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION Expires October 01, 1996 [Page 77] Internet Draft SNANAU APPN MIB April 1996 "Fully qualified network LU name in the domain of the serving network node. Entries take one of three forms: - Explicit entries do not contain the character '*'. - Partial wildcard entries have the form 'ccc*', where 'c' represents a character in a legal SNA LuName. - A full wildcard entry consists of the single character '*" ::= { appnDirEntry 1 } appnDirNnServerName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "Fully qualified control point (CP) name of the network node server. For unassociated end node entries, a string of length 0 is returned." ::= { appnDirEntry 2 } appnDirLuOwnerName OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "Fully qualified CP name of the node at which the LU is located. This name is the same as the serving NN name when the LU is located at a network node. It is also the same as the fully qualified LU name when this is the control point LU for this node." ::= { appnDirEntry 3 } appnDirLuLocation OBJECT-TYPE SYNTAX INTEGER { local(1), --Local domain(2), --Domain xdomain(3) --Cross Domain } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the location of the LU with respect to the local node." Expires October 01, 1996 [Page 78] Internet Draft SNANAU APPN MIB April 1996 ::= { appnDirEntry 4 } appnDirType OBJECT-TYPE SYNTAX INTEGER { home(1), --defined as home entry cache(2), --learned over time registered(3) --registered by end node } MAX-ACCESS read-only STATUS current DESCRIPTION "Directory types are: 1 - Home The LU is in the domain of the local node, and the LU information has been configured at the local node. 2 - Cache The LU has previously been located by a broadcast search, and the location information has been saved. 3 - Registered The LU is at an end node that is in the domain of the local network node. Registered entries are registered by the served end node." ::= { appnDirEntry 5 } -- ************** The APPN Class of Service Group ********************** appnCos OBJECT IDENTIFIER ::= { appnObjects 5 } -- The APPN Class of Service (COS) -- Class of Service is a means of expressing the quality of routes and -- the transmission priority of traffic that flows on these routes. -- The quality of routes is specified by two tables, a COS weight table -- for TGs and a COS weight table for nodes. Values in these COS tables -- are administratively assigned at each APPN node, with seven default -- tables specified by the APPN architecture. -- ********************************************************************* appnCosModeTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnCosModeEntry MAX-ACCESS not-accessible STATUS current Expires October 01, 1996 [Page 79] Internet Draft SNANAU APPN MIB April 1996 DESCRIPTION "Table representing all of the defined mode names for this node. The table contains the matching COS name for each mode name." ::= { appnCos 1 } appnCosModeEntry OBJECT-TYPE SYNTAX AppnCosModeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by the mode name." INDEX {appnCosModeName} ::= { appnCosModeTable 1 } AppnCosModeEntry ::= SEQUENCE { appnCosModeName DisplayString, appnCosModeCosName DisplayString } appnCosModeName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Administratively assigned name for this mode." ::= { appnCosModeEntry 1 } appnCosModeCosName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Administratively assigned name for this class of service." ::= { appnCosModeEntry 2 } -- ********************************************************************* appnCosNameTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnCosNameEntry Expires October 01, 1996 [Page 80] Internet Draft SNANAU APPN MIB April 1996 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table mapping all of the defined class-of-service names for this node to their network transmission priorities." ::= { appnCos 2 } appnCosNameEntry OBJECT-TYPE SYNTAX AppnCosNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The COS name is the index to this table." INDEX {appnCosName} ::= { appnCosNameTable 1 } AppnCosNameEntry ::= SEQUENCE { appnCosName DisplayString, appnCosTransPriority INTEGER } appnCosName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Administratively assigned name for this class of service." ::= { appnCosNameEntry 1 } appnCosTransPriority OBJECT-TYPE SYNTAX INTEGER { low(1), --X'01' medium(2), --X'02' high(3), --X'03' network(4) --X'04' } MAX-ACCESS read-only STATUS current DESCRIPTION "Transmission priority for this class of service." Expires October 01, 1996 [Page 81] Internet Draft SNANAU APPN MIB April 1996 ::= { appnCosNameEntry 2 } -- ********************************************************************* appnCosNodeRowTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnCosNodeRowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains all node-row information for all classes of service defined in this node." ::= { appnCos 3 } appnCosNodeRowEntry OBJECT-TYPE SYNTAX AppnCosNodeRowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A node entry for a given class of service." INDEX {appnCosNodeRowName, appnCosNodeRowIndex} ::= { appnCosNodeRowTable 1 } AppnCosNodeRowEntry ::= SEQUENCE { appnCosNodeRowName DisplayString, appnCosNodeRowIndex INTEGER, appnCosNodeRowWgt DisplayString, appnCosNodeRowResistMin INTEGER, appnCosNodeRowResistMax INTEGER, appnCosNodeRowMinCongestAllow INTEGER, appnCosNodeRowMaxCongestAllow INTEGER } appnCosNodeRowName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Administratively assigned name for this class of service." ::= { appnCosNodeRowEntry 1 } Expires October 01, 1996 [Page 82] Internet Draft SNANAU APPN MIB April 1996 appnCosNodeRowIndex OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Subindex under appnCosNodeRowName, corresponding to a row in the node table for the class of service identified in appnCosNodeRowName. For each class of service, this subindex orders rows in the appnCosNodeRowTable in the same order as that used for route calculation in the APPN node." ::= { appnCosNodeRowEntry 2 } appnCosNodeRowWgt OBJECT-TYPE SYNTAX DisplayString (SIZE (1..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Weight to be associated with the nodes that fit the criteria specified by this node row. This value can either be a character representation of an integer, or a formula for calculating the weight." ::= { appnCosNodeRowEntry 3 } appnCosNodeRowResistMin OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum route addition resistance value for this node. Range of values is 0-255. The lower the value, the more desirable the node is for intermediate routing." ::= { appnCosNodeRowEntry 4 } appnCosNodeRowResistMax OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum route addition resistance value for this node. Range of values is 0-255. The lower the value, the more Expires October 01, 1996 [Page 83] Internet Draft SNANAU APPN MIB April 1996 desirable the node is for intermediate routing." ::= { appnCosNodeRowEntry 5 } appnCosNodeRowMinCongestAllow OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether low congestion will be tolerated. The minimum and maximum parameters will allow specifying either low-congested, high-congested, or either to be used." ::= { appnCosNodeRowEntry 6 } appnCosNodeRowMaxCongestAllow OBJECT-TYPE SYNTAX INTEGER {yes(1), no(2)} MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether high congestion will be tolerated. The minimum and maximum parameters will allow specifying either low-congested, high-congested, or either to be used." ::= { appnCosNodeRowEntry 7 } -- ********************************************************************* appnCosTgRowTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnCosTgRowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table containing all the TG-row information for all classes of service defined in this node." ::= { appnCos 4 } appnCosTgRowEntry OBJECT-TYPE SYNTAX AppnCosTgRowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A TG entry for a given class of service." INDEX Expires October 01, 1996 [Page 84] Internet Draft SNANAU APPN MIB April 1996 {appnCosTgRowName, appnCosTgRowIndex} ::= { appnCosTgRowTable 1 } AppnCosTgRowEntry ::= SEQUENCE { appnCosTgRowName DisplayString, appnCosTgRowIndex INTEGER, appnCosTgRowWgt DisplayString, appnCosTgRowEffCapMin OCTET STRING, appnCosTgRowEffCapMax OCTET STRING, appnCosTgRowConnCostMin INTEGER, appnCosTgRowConnCostMax INTEGER, appnCosTgRowByteCostMin INTEGER, appnCosTgRowByteCostMax INTEGER, appnCosTgRowSecurityMin INTEGER, appnCosTgRowSecurityMax INTEGER, appnCosTgRowDelayMin OCTET STRING, appnCosTgRowDelayMax OCTET STRING, appnCosTgRowUsr1Min INTEGER, appnCosTgRowUsr1Max INTEGER, appnCosTgRowUsr2Min INTEGER, appnCosTgRowUsr2Max INTEGER, appnCosTgRowUsr3Min INTEGER, appnCosTgRowUsr3Max INTEGER } appnCosTgRowName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Administratively assigned name for this class of service." ::= { appnCosTgRowEntry 1 } appnCosTgRowIndex OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Subindex under appnCosTgRowName, corresponding to a row in the TG table for the class of service identified in appnCosTgRowName. For each class of service, this subindex orders rows in the Expires October 01, 1996 [Page 85] Internet Draft SNANAU APPN MIB April 1996 appnCosTgRowTable in the same order as that used for route calculation in the APPN node." ::= { appnCosTgRowEntry 2 } appnCosTgRowWgt OBJECT-TYPE SYNTAX DisplayString (SIZE (1..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Weight to be associated with the TGs that fit the criteria specified by this TG row. This value can either be a character representation of an integer, or a formula for calculating the weight." ::= { appnCosTgRowEntry 3 } appnCosTgRowEffCapMin OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum acceptable speed for this class of service. This value is derived from the link bandwidth and maximum load factor. It is encoded in the same way as byte 7 of cv47, and represents a floating-point number in units of 300 bits per second." ::= { appnCosTgRowEntry 4 } appnCosTgRowEffCapMax OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum acceptable speed for this class of service. This value is derived from the link bandwidth and maximum load factor. It is encoded in the same way as byte 7 of cv47, and represents a floating-point number in units of 300 bits per second." ::= { appnCosTgRowEntry 5 } Expires October 01, 1996 [Page 86] Internet Draft SNANAU APPN MIB April 1996 appnCosTgRowConnCostMin OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum acceptable cost per connect time for this class of service. Cost per connect time: a value representing the relative cost per unit of time to use this TG. Range is from 0, which means no cost, to 255." ::= { appnCosTgRowEntry 6 } appnCosTgRowConnCostMax OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum acceptable cost per connect time for this class of service. Cost per connect time: a value representing the relative cost per unit of time to use this TG. Range is from 0, which means no cost, to 255." ::= { appnCosTgRowEntry 7 } appnCosTgRowByteCostMin OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum acceptable cost per byte transmitted for this class of service. Cost per byte transmitted: a value representing the relative cost per unit of time to use this TG. Range is from 0, which means no cost, to 255." ::= { appnCosTgRowEntry 8 } appnCosTgRowByteCostMax OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current Expires October 01, 1996 [Page 87] Internet Draft SNANAU APPN MIB April 1996 DESCRIPTION "Maximum acceptable cost per byte transmitted for this class of service. Cost per byte transmitted: a value representing the relative cost of transmitting a byte over this TG. Range is from 0, which means no cost, to 255." ::= { appnCosTgRowEntry 9 } appnCosTgRowSecurityMin OBJECT-TYPE SYNTAX INTEGER { nonsecure(1), -- X'01' publicSwitchedNetwork(32), -- X'20' undergroundCable(64), -- X'40' secureConduit(96), -- X'60' guardedConduit(128), -- X'80' encrypted(160), -- X'A0' guardedRadiation(192) -- X'C0' } MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum acceptable security for this class of service. If a network needs security values other than the architecturally defined ones listed here, one of the three user-defined characteristics may be used to specify the required additional security values." ::= { appnCosTgRowEntry 10 } appnCosTgRowSecurityMax OBJECT-TYPE SYNTAX INTEGER { nonsecure(1), -- X'01' publicSwitchedNetwork(32), -- X'20' undergroundCable(64), -- X'40' secureConduit(96), -- X'60' guardedConduit(128), -- X'80' encrypted(160), -- X'A0' guardedRadiation(192) -- X'C0' } MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum acceptable security for this class of service. Expires October 01, 1996 [Page 88] Internet Draft SNANAU APPN MIB April 1996 If a network needs security values other than the architecturally defined ones listed here, one of the three user-defined characteristics may be used to specify the required additional security values." ::= { appnCosTgRowEntry 11 } appnCosTgRowDelayMin OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum acceptable propagation delay for this class of service. Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in microseconds, using the same encoding scheme used in cv47 in a topology update. Some of the more common values, along with their encoded hex values, are: minimum(0), X'00' negligible(384), X'4C' terrestrial(9216), X'71' packet(147456), X'91' long(294912), X'99' maximum(2013265920) X'FF' " ::= { appnCosTgRowEntry 12 } appnCosTgRowDelayMax OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum acceptable propagation delay for this class of service. Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in microseconds, using the same encoding scheme used in cv47 in a topology update. Some of the more common values, along with their encoded hex values, are: minimum(0), X'00' Expires October 01, 1996 [Page 89] Internet Draft SNANAU APPN MIB April 1996 negligible(384), X'4C' terrestrial(9216), X'71' packet(147456), X'91' long(294912), X'99' maximum(2013265920) X'FF' " ::= { appnCosTgRowEntry 13 } appnCosTgRowUsr1Min OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum acceptable value for this user-defined characteristic." ::= { appnCosTgRowEntry 14 } appnCosTgRowUsr1Max OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum acceptable value for this user-defined characteristic." ::= { appnCosTgRowEntry 15 } appnCosTgRowUsr2Min OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum acceptable value for this user-defined characteristic." ::= { appnCosTgRowEntry 16 } appnCosTgRowUsr2Max OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum acceptable value for this user-defined characteristic." Expires October 01, 1996 [Page 90] Internet Draft SNANAU APPN MIB April 1996 ::= { appnCosTgRowEntry 17 } appnCosTgRowUsr3Min OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Minimum acceptable value for this user-defined characteristic." ::= { appnCosTgRowEntry 18 } appnCosTgRowUsr3Max OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum acceptable value for this user-defined characteristic." ::= { appnCosTgRowEntry 19 } -- ********************************************************************* -- Intermediate Session Information -- ********************************************************************* appnSessIntermediate OBJECT IDENTIFIER ::= { appnObjects 6 } -- ********************************************************************* -- Intermediate Session Information Global Objects -- --------------------------------------------------------------------- -- The following simple objects allow the collection of intermediate -- session Information to be started and stopped. -- ********************************************************************* appnIsInGlobal OBJECT IDENTIFIER ::= { appnSessIntermediate 1 } appnIsInGlobeCtrAdminStatus OBJECT-TYPE SYNTAX INTEGER { notActive(1), active(2), ready(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Object by which a Management Station can deactivate or activate capture of intermediate-session counter data and Expires October 01, 1996 [Page 91] Internet Draft SNANAU APPN MIB April 1996 names, by setting the value to notActive(1) or active(2), respectively. The value ready(3) has no meaning on a set operation; it is returned in response to a get operation if no set operation has been directed to this object. The counters referred to here are the eight objects in the AppnIsInTable, from appnIsInP2SFmdPius through appnIsInS2PNonFmdBytes. The names are the four objects in this table, from appnIsInPriLuName through appnIsInCosName. Setting this object to the following values has the following effects: notActive(1) stop collecting counter data. If a counter is queried, it returns the value 0. Collection of names may, but need not be, disabled. active(2) start collecting counter data. If it is supported, collection of names is enabled." ::= { appnIsInGlobal 1 } appnIsInGlobeCtrOperStatus OBJECT-TYPE SYNTAX INTEGER { notActive(1), active(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether or not the intermediate session counters are active. The counters referred to here are the eight objects in the AppnIsInTable, from appnIsInP2SFmdPius through appnIsInS2PNonFmdBytes. These eight counters are of type Integer32 rather than Counter32 because when this object enters the notActive state, either because a Management Station has set appnInInGlobeCtrAdminStatus to notActive or because of a locally-initiated transition, the counters are all reset to 0. The values for this object are: notActive(1): collection of counters is not active; if it is queried, a counter returns the value 0. active(2): collection of counters is active." Expires October 01, 1996 [Page 92] Internet Draft SNANAU APPN MIB April 1996 ::= { appnIsInGlobal 2 } appnIsInGlobeCtrStatusTime OBJECT-TYPE SYNTAX TimeTicks UNITS "hundredths of a second" MAX-ACCESS read-only STATUS current DESCRIPTION "The time since the appnIsInGlobeCtrOperStatus object last changed, measured in hundredths of a second. This time can be used to identify when this change occurred in relation to other events in the agent, such as the last time the APPN node was re-initialized." ::= { appnIsInGlobal 3 } appnIsInGlobeRscv OBJECT-TYPE SYNTAX INTEGER { notActive(1), active(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the current RSCV collection option in effect, and allows a Management Station to change the option. The values for this object are: notActive(1): collection of route selection control vectors is not active. active(2): collection of route selection control vectors is active." ::= { appnIsInGlobal 4 } appnIsInGlobeRscvTime OBJECT-TYPE SYNTAX TimeTicks UNITS "hundredths of a second" MAX-ACCESS read-only STATUS current DESCRIPTION "The time since the appnIsInGlobeRscv object last changed, measured in hundredths of a second. This time can be used to identify when this change occurred in relation to other events in the agent, such as the last time the APPN node was Expires October 01, 1996 [Page 93] Internet Draft SNANAU APPN MIB April 1996 re-initialized." ::= { appnIsInGlobal 5 } appnIsInGlobeActSess OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of currently active intermediate sessions." ::= { appnIsInGlobal 6 } appnIsInGlobeHprBfActSess OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of currently active HPR intermediate sessions." ::= { appnIsInGlobal 7 } -- ********************************************************************* -- Intermediate Session Information Table -- --------------------------------------------------------------------- -- This table contains information on intermediate sessions -- which are currently active. -- ********************************************************************* appnIsInTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnIsInEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Intermediate Session Information Table" ::= { appnSessIntermediate 2 } appnIsInEntry OBJECT-TYPE SYNTAX AppnIsInEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of Intermediate Session Information Table." INDEX Expires October 01, 1996 [Page 94] Internet Draft SNANAU APPN MIB April 1996 { appnIsInFqCpName, appnIsInPcid } ::= { appnIsInTable 1 } AppnIsInEntry ::= SEQUENCE { appnIsInFqCpName DisplayString, appnIsInPcid OCTET STRING, appnIsInSessState INTEGER, appnIsInPriLuName DisplayString, appnIsInSecLuName DisplayString, appnIsInModeName DisplayString, appnIsInCosName DisplayString, appnIsInTransPriority INTEGER, appnIsInSessType INTEGER, appnIsInSessUpTime TimeTicks, appnIsInCtrUpTime TimeTicks, appnIsInP2SFmdPius Integer32, appnIsInS2PFmdPius Integer32, appnIsInP2SNonFmdPius Integer32, appnIsInS2PNonFmdPius Integer32, appnIsInP2SFmdBytes Integer32, appnIsInS2PFmdBytes Integer32, appnIsInP2SNonFmdBytes Integer32, appnIsInS2PNonFmdBytes Integer32, appnIsInPsAdjCpName DisplayString, appnIsInPsAdjTgNum INTEGER, appnIsInPsSendMaxBtuSize INTEGER, appnIsInPsSendPacingType INTEGER, appnIsInPsSendRpc Gauge32, appnIsInPsSendNxWndwSize Gauge32, appnIsInPsRecvPacingType INTEGER, appnIsInPsRecvRpc Gauge32, appnIsInPsRecvNxWndwSize Gauge32, appnIsInSsAdjCpName DisplayString, appnIsInSsAdjTgNum INTEGER, appnIsInSsSendMaxBtuSize INTEGER, appnIsInSsSendPacingType INTEGER, appnIsInSsSendRpc Gauge32, appnIsInSsSendNxWndwSize Gauge32, appnIsInSsRecvPacingType INTEGER, Expires October 01, 1996 [Page 95] Internet Draft SNANAU APPN MIB April 1996 appnIsInSsRecvRpc Gauge32, appnIsInSsRecvNxWndwSize Gauge32, appnIsInRouteInfo OCTET STRING, appnIsInRtpNceId OCTET STRING, appnIsInRtpTcid OCTET STRING } appnIsInFqCpName OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The network-qualified control point name of the node at which the session and PCID originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. For DLUR resources, it is the name of the owning SSCP. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name." ::= { appnIsInEntry 1 } appnIsInPcid OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The procedure correlation identifier (PCID) of a session. It is an 8-octet value assigned by the primary LU." ::= { appnIsInEntry 2 } appnIsInSessState OBJECT-TYPE SYNTAX INTEGER { inactive(1), pendactive(2), active(3), pendinact(4) } MAX-ACCESS read-write STATUS current DESCRIPTION Expires October 01, 1996 [Page 96] Internet Draft SNANAU APPN MIB April 1996 "Indicates the state of the session: 1. session is pending inactive 2. session is pending active 3. session is active 4. session is inactive Active sessions can be deactivated by setting this object to inactive." ::= { appnIsInEntry 3 } appnIsInPriLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The primary LU name of the session. A zero-length string indicates that this name is not available." ::= { appnIsInEntry 4 } appnIsInSecLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The secondary LU name of the session. A zero-length string indicates that this name is not available." ::= { appnIsInEntry 5 } appnIsInModeName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The mode name used for this session. A zero-length string indicates that this name is not available." ::= { appnIsInEntry 6 } appnIsInCosName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-only STATUS current Expires October 01, 1996 [Page 97] Internet Draft SNANAU APPN MIB April 1996 DESCRIPTION "The Class of Service (COS) name used for this session. A zero-length string indicates that this name is not available." ::= { appnIsInEntry 7 } appnIsInTransPriority OBJECT-TYPE SYNTAX INTEGER { low(1), --X'01' medium(2), --X'02' high(3), --X'03' network(4) --X'04' } MAX-ACCESS read-only STATUS current DESCRIPTION "Transmission priority for this class of service. Values are: - low - medium - high - network " ::= { appnIsInEntry 8 } appnIsInSessType OBJECT-TYPE SYNTAX INTEGER { unknown(1), lu62(2), lu0thru3(3), lu62dlur(4), lu0thru3dlur(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of intermediate session. Defined values are unknown The session type is not known. lu62 A session between LUs of type 6.2 (as indicated by the LU type in Bind) lu0thru3 A session between LUs of type 0, 1, 2, or 3 (as indicated by the LU type in Bind) Expires October 01, 1996 [Page 98] Internet Draft SNANAU APPN MIB April 1996 lu62dlur A session between LUs of type 6.2 (as indicated by the LU type in Bind). One of the LUs is a dependent LU supported by the dependent LU requester (DLUR) function at this node. lu0thru3dlur A session between LUs of type 0, 1, 2, or 3 (as indicated by the LU type in Bind) One of the LUs is a dependent LU supported by the dependent LU requester (DLUR) function at this node." ::= { appnIsInEntry 9 } appnIsInSessUpTime OBJECT-TYPE SYNTAX TimeTicks UNITS "hundredths of a second" MAX-ACCESS read-only STATUS current DESCRIPTION "Length of time the session has been active, measured in hundredths of a second." ::= { appnIsInEntry 10 } appnIsInCtrUpTime OBJECT-TYPE SYNTAX TimeTicks UNITS "hundredths of a second" MAX-ACCESS read-only STATUS current DESCRIPTION "Length of time the session counters have been active, measured in hundredths of a second." ::= { appnIsInEntry 11 } appnIsInP2SFmdPius OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of FMD PIUs sent from the Primary LU to the Secondary LU since the counters were last activated." ::= { appnIsInEntry 12 } Expires October 01, 1996 [Page 99] Internet Draft SNANAU APPN MIB April 1996 appnIsInS2PFmdPius OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of FMD PIUs sent from the Secondary LU to the Primary LU since the counters were last activated." ::= { appnIsInEntry 13 } appnIsInP2SNonFmdPius OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of non-FMD PIUs sent from the Primary LU to the Secondary LU since the counters were last activated." ::= { appnIsInEntry 14 } appnIsInS2PNonFmdPius OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of non-FMD PIUs sent from the Secondary LU to the Primary LU since the counters were last activated." ::= { appnIsInEntry 15 } appnIsInP2SFmdBytes OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of FMD bytes sent from the Primary LU to the Secondary LU since the counters were last activated." ::= { appnIsInEntry 16 } appnIsInS2PFmdBytes OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of FMD bytes sent from the Secondary LU to the Primary Expires October 01, 1996 [Page 100] Internet Draft SNANAU APPN MIB April 1996 LU since the counters were last activated." ::= { appnIsInEntry 17 } appnIsInP2SNonFmdBytes OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of non-FMD bytes sent from the Primary LU to the Secondary LU since the counters were last activated." ::= { appnIsInEntry 18 } appnIsInS2PNonFmdBytes OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of non-FMD bytes sent from the Secondary LU to the Primary LU since the counters were last activated." ::= { appnIsInEntry 19 } appnIsInPsAdjCpName OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The primary stage adjacent CP name of this session." ::= { appnIsInEntry 20 } appnIsInPsAdjTgNum OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The primary stage adjacent transmission group (TG) number associated with this session." ::= { appnIsInEntry 21 } appnIsInPsSendMaxBtuSize OBJECT-TYPE SYNTAX INTEGER (99..32767) UNITS "bytes" Expires October 01, 1996 [Page 101] Internet Draft SNANAU APPN MIB April 1996 MAX-ACCESS read-only STATUS current DESCRIPTION "The primary stage maximum basic transmission unit (BTU) size for sending data." ::= { appnIsInEntry 22 } appnIsInPsSendPacingType OBJECT-TYPE SYNTAX INTEGER { fixed(1), adaptive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The primary stage type of pacing being used for sending data." ::= { appnIsInEntry 23 } appnIsInPsSendRpc OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The primary stage send residual pace count. This represents the primary stage number of MU's that can still be sent in the current session window." ::= { appnIsInEntry 24 } appnIsInPsSendNxWndwSize OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The primary stage size of the next window which will be used to send data." ::= { appnIsInEntry 25 } appnIsInPsRecvPacingType OBJECT-TYPE SYNTAX INTEGER { fixed(1), adaptive(2) Expires October 01, 1996 [Page 102] Internet Draft SNANAU APPN MIB April 1996 } MAX-ACCESS read-only STATUS current DESCRIPTION "The primary stage type of pacing being used for receiving data." ::= { appnIsInEntry 26 } appnIsInPsRecvRpc OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The primary stage receive residual pace count. This represents the primary stage number of MU's that can still be received in the current session window." ::= { appnIsInEntry 27 } appnIsInPsRecvNxWndwSize OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The primary stage size of the next window which will be used to receive data." ::= { appnIsInEntry 28 } appnIsInSsAdjCpName OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The secondary stage adjacent CP name of this session." ::= { appnIsInEntry 29 } appnIsInSsAdjTgNum OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The secondary stage adjacent transmission group (TG) number associated with this session." Expires October 01, 1996 [Page 103] Internet Draft SNANAU APPN MIB April 1996 ::= { appnIsInEntry 30 } appnIsInSsSendMaxBtuSize OBJECT-TYPE SYNTAX INTEGER (99..32767) UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "The secondary stage maximum basic transmission unit (BTU) size for sending data." ::= { appnIsInEntry 31 } appnIsInSsSendPacingType OBJECT-TYPE SYNTAX INTEGER { fixed(1), adaptive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The secondary stage type of pacing being used for sending data." ::= { appnIsInEntry 32 } appnIsInSsSendRpc OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The secondary stage send residual pace count. This represents the secondary stage number of MU's that can still be sent in the current session window." ::= { appnIsInEntry 33 } appnIsInSsSendNxWndwSize OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The secondary stage size of the next window which will be used to send data." ::= { appnIsInEntry 34 } Expires October 01, 1996 [Page 104] Internet Draft SNANAU APPN MIB April 1996 appnIsInSsRecvPacingType OBJECT-TYPE SYNTAX INTEGER { fixed(1), adaptive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The secondary stage type of pacing being used for receiving data." ::= { appnIsInEntry 35 } appnIsInSsRecvRpc OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The secondary stage send residual pace count. This represents the secondary stage number of MU's that can still be received in the current session window." ::= { appnIsInEntry 36 } appnIsInSsRecvNxWndwSize OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The secondary stage size of the next window which will be used to receive data." ::= { appnIsInEntry 37 } appnIsInRouteInfo OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The route selection control vector (RSCV x'2B') used for this session. It is present for APPN nodes; but is not present for LEN nodes. The format of this vector is described in SNA Formats." ::= { appnIsInEntry 38 } Expires October 01, 1996 [Page 105] Internet Draft SNANAU APPN MIB April 1996 appnIsInRtpNceId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The HPR local Network Connection Endpoint of the session." ::= { appnIsInEntry 39 } appnIsInRtpTcid OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The RTP connection local TCID of the session." ::= { appnIsInEntry 40 } -- ********************************************************************* -- Intermediate Session RTP Table -- --------------------------------------------------------------------- -- This table contains information on intermediate sessions that are -- being transported on RTP connections by High Performance Routing (HPR) -- ********************************************************************* appnIsRtpTable OBJECT-TYPE SYNTAX SEQUENCE OF AppnIsRtpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table indicating how many ISR sessions are transported by each RTP connection." ::= { appnSessIntermediate 3 } appnIsRtpEntry OBJECT-TYPE SYNTAX AppnIsRtpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of Intermediate Session RTP Table." INDEX { appnIsRtpNceId, appnIsRtpTcid } ::= { appnIsRtpTable 1 } Expires October 01, 1996 [Page 106] Internet Draft SNANAU APPN MIB April 1996 AppnIsRtpEntry ::= SEQUENCE { appnIsRtpNceId OCTET STRING, appnIsRtpTcid OCTET STRING, appnIsRtpSessions Gauge32 } appnIsRtpNceId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The local Network Connection Endpoint of the RTP connection." ::= { appnIsRtpEntry 1 } appnIsRtpTcid OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The local TCID of the RTP connection." ::= { appnIsRtpEntry 2 } appnIsRtpSessions OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of intermediate sessions using this RTP connection." ::= { appnIsRtpEntry 3 } -- ********************************************************************* appnTraps OBJECT IDENTIFIER ::= { appnMIB 2 } -- ********************************************************************* alertTrap NOTIFICATION-TYPE OBJECTS { alertIdNumber, affectedObject } STATUS current DESCRIPTION "This trap carries a 32-bit SNA/MS Alert ID Number, as specified in SNA Formats." Expires October 01, 1996 [Page 107] Internet Draft SNANAU APPN MIB April 1996 ::= { appnTraps 1 } alertIdNumber OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4)) MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit SNA/MS Alert ID Number, as specified in SNA Formats." ::= { appnTraps 2 } affectedObject OBJECT-TYPE SYNTAX VariablePointer MAX-ACCESS read-only STATUS current DESCRIPTION "The MIB object associated with the Alert condition, if there is an object associated with it." ::= { appnTraps 3 } -- ********************************************************************* -- Conformance information -- ********************************************************************* appnConformance OBJECT IDENTIFIER ::= {appnMIB 3 } appnCompliances OBJECT IDENTIFIER ::= {appnConformance 1 } appnGroups OBJECT IDENTIFIER ::= {appnConformance 2 } -- Compliance statements appnCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the SNMPv2 entities which implement the APPN MIB." MODULE -- this module -- Unconditionally mandatory groups MANDATORY-GROUPS { appnGeneralConfGroup, appnPortConfGroup, appnLinkConfGroup, appnLocalTgConfGroup, appnDirTableConfGroup } Expires October 01, 1996 [Page 108] Internet Draft SNANAU APPN MIB April 1996 -- Conditionally mandatory groups GROUP appnNnUniqueConfGroup DESCRIPTION "The appnNnUniqueConfGroup is mandatory only for network nodes." GROUP appnEnUniqueConfGroup DESCRIPTION "The appnEnUniqueConfGroup is mandatory only for end nodes." GROUP appnVrnConfGroup DESCRIPTION "The appnVrnConfGroup is mandatory only for network nodes and end nodes that implement virtual routing node support." GROUP appnNnTopoConfGroup DESCRIPTION "The appnNnTopoConfGroup is mandatory only for network nodes." GROUP appnLocalEnTopoConfGroup DESCRIPTION "The appnLocalEnTopoConfGroup is mandatory only for network nodes." GROUP appnLocalDirPerfConfGroup DESCRIPTION "The appnLocalDirPerfConfGroup is mandatory only for network nodes and end nodes." GROUP appnCosConfGroup DESCRIPTION "The appnCosConfGroup is mandatory only for network nodes and end nodes." GROUP appnIntSessConfGroup DESCRIPTION "The appnIntSessConfGroup is mandatory only for network nodes." GROUP appnHprBaseConfGroup DESCRIPTION "The appnHprBaseConfGroup is mandatory only for nodes that implement the HPR base (APPN option Expires October 01, 1996 [Page 109] Internet Draft SNANAU APPN MIB April 1996 set 1400)." GROUP appnHprRtpConfGroup DESCRIPTION "The appnHprRtpConfGroup is mandatory only for nodes that implement the HPR RTP tower (APPN option set 1401)." GROUP appnHprCtrlFlowsRtpConfGroup DESCRIPTION "The appnHprCtrlFlowsRtpConfGroup is mandatory only for nodes that implement the HPR Control Flows over RTP tower (APPN option set 1402)." GROUP appnHprBfConfGroup DESCRIPTION "The appnHprBfConfGroup is mandatory only for nodes that implement the APPN/HPR boundary function." GROUP appnTrapConfGroup DESCRIPTION "Traps are optional for all nodes." ::= {appnCompliances 1 } -- Units of conformance appnGeneralConfGroup OBJECT-GROUP OBJECTS { appnNodeCpName, appnNodeMibVersion, appnNodeId, appnNodeType, appnNodeUpTime, appnNodeParallelTg, appnNodeAdaptiveBindPacing, appnNodeHprSupport } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPN general information and capabilities." ::= { appnGroups 1 } appnPortConfGroup OBJECT-GROUP OBJECTS { appnPortAdminState, Expires October 01, 1996 [Page 110] Internet Draft SNANAU APPN MIB April 1996 appnPortOperState, appnPortDlcType, appnPortPortType, appnPortSIMRIM, appnPortLsRole, appnPortNegotLs, appnPortDynamicLinkSupport, appnPortMaxRcvBtuSize, appnPortMaxIframeWindow, appnPortDefLsGoodXids, appnPortDefLsBadXids, appnPortDynLsGoodXids, appnPortDynLsBadXids, appnPortSpecific, appnPortDlcLocalAddr } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPN port information." ::= { appnGroups 2 } appnLinkConfGroup OBJECT-GROUP OBJECTS { appnLsAdminState, appnLsOperState, appnLsPortName, appnLsDlcType, appnLsDynamic, appnLsAdjCpName, appnLsAdjNodeType, appnLsTgNum, appnLsLimResource, appnLsActOnDemand, appnLsMigration, appnLsPartnerNodeId, appnLsCpCpSessionSupport, appnLsMaxSendBtuSize, appnLsInXidBytes, appnLsInMsgBytes, appnLsInXidFrames, appnLsInMsgFrames, appnLsOutXidBytes, appnLsOutMsgBytes, appnLsOutXidFrames, appnLsOutMsgFrames, Expires October 01, 1996 [Page 111] Internet Draft SNANAU APPN MIB April 1996 appnLsEchoRsps, appnLsCurrentDelay, appnLsMaxDelay, appnLsMinDelay, appnLsMaxDelayTime, appnLsGoodXids, appnLsBadXids, appnLsSpecific, appnLsActiveTime, appnLsCurrentStateTime, appnLsHprSup, appnLsLocalAddr, appnLsRemoteAddr, appnLsRemoteLsName, appnLsStatusTime, appnLsStatusLsName, appnLsStatusCpName, appnLsStatusPartnerId, appnLsStatusTgNum, appnLsStatusGeneralSense, appnLsStatusRetry, appnLsStatusEndSense, appnLsStatusXidLocalSense, appnLsStatusXidRemoteSense, appnLsStatusXidByteInError, appnLsStatusXidBitInError, appnLsStatusDlcType, appnLsStatusLocalAddr, appnLsStatusRemoteAddr } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPN link information." ::= { appnGroups 3 } appnLocalTgConfGroup OBJECT-GROUP OBJECTS { appnLocalTgDestVirtual, appnLocalTgDlcData, appnLocalTgPortName, appnLocalTgQuiescing, appnLocalTgOperational, appnLocalTgCpCpSession, appnLocalTgEffCap, appnLocalTgConnCost, Expires October 01, 1996 [Page 112] Internet Draft SNANAU APPN MIB April 1996 appnLocalTgByteCost, appnLocalTgSecurity, appnLocalTgDelay, appnLocalTgUsr1, appnLocalTgUsr2, appnLocalTgUsr3, appnLocalTgHprSup, appnLocalTgIntersubnet } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPN local TG information." ::= { appnGroups 4 } appnDirTableConfGroup OBJECT-GROUP OBJECTS { appnDirNnServerName, appnDirLuOwnerName, appnDirLuLocation, appnDirType } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of the APPN directory database." ::= { appnGroups 5 } appnNnUniqueConfGroup OBJECT-GROUP OBJECTS { appnNodeNnCentralDirectory, appnNodeNnTreeCache, appnNodeNnRouteAddResist, appnNodeNnIsr, appnNodeNnFrsn, appnNodeNnPeriBorderSup, appnNodeNnInterchangeSup, appnNodeNnExteBorderSup, appnNodeNnSafeStoreFreq, appnNodeNnRsn, appnNodeNnCongested, appnNodeNnIsrDepleted, appnNodeNnQuiescing, appnNodeNnGateway } STATUS current Expires October 01, 1996 [Page 113] Internet Draft SNANAU APPN MIB April 1996 DESCRIPTION "The appnNnUniqueConfGroup is mandatory only for network nodes." ::= { appnGroups 6 } appnEnUniqueConfGroup OBJECT-GROUP OBJECTS { appnNodeEnModeCosMap, appnNodeEnNnServer, appnNodeEnLuSearch } STATUS current DESCRIPTION "The appnEnUniqueConfGroup is mandatory only for end nodes." ::= { appnGroups 7 } appnVrnConfGroup OBJECT-GROUP OBJECTS { appnVrnPortName } STATUS current DESCRIPTION "The appnVrnConfGroup is mandatory only for network nodes and end nodes." ::= { appnGroups 8 } appnNnTopoConfGroup OBJECT-GROUP OBJECTS { appnNnTopoMaxNodes, appnNnTopoCurNumNodes, appnNnTopoNodePurges, appnNnTopoTgPurges, appnNnTopoTotalTduWars, appnNnNodeFREntryTimeLeft, appnNnNodeFRType, appnNnNodeFRRsn, appnNnNodeFRRouteAddResist, appnNnNodeFRCongested, appnNnNodeFRIsrDepleted, appnNnNodeFRQuiescing, appnNnNodeFRGateway, appnNnNodeFRCentralDirectory, appnNnNodeFRIsr, appnNnNodeFRGarbageCollect, appnNnNodeFRHprSupport, Expires October 01, 1996 [Page 114] Internet Draft SNANAU APPN MIB April 1996 appnNnNodeFRPeriBorderSup, appnNnNodeFRInterchangeSup, appnNnNodeFRExteBorderSup, appnNnTgFREntryTimeLeft, appnNnTgFRDestVirtual, appnNnTgFRDlcData, appnNnTgFRRsn, appnNnTgFROperational, appnNnTgFRQuiescing, appnNnTgFRCpCpSession, appnNnTgFREffCap, appnNnTgFRConnCost, appnNnTgFRByteCost, appnNnTgFRSecurity, appnNnTgFRDelay, appnNnTgFRUsr1, appnNnTgFRUsr2, appnNnTgFRUsr3, appnNnTgFRGarbageCollect, appnNnTgFRSubareaNum, appnNnTgFRHprSup, appnNnTgFRDestHprTrans, appnNnTgFRTypeIndicator, appnNnTgFRIntersubnet } STATUS current DESCRIPTION "The appnNnTopoConfGroup is mandatory only for network nodes." ::= { appnGroups 9 } appnLocalEnTopoConfGroup OBJECT-GROUP OBJECTS { appnLocalEnTgEntryTimeLeft, appnLocalEnTgDestVirtual, appnLocalEnTgDlcData, appnLocalEnTgOperational, appnLocalEnTgCpCpSession, appnLocalEnTgEffCap, appnLocalEnTgConnCost, appnLocalEnTgByteCost, appnLocalEnTgSecurity, appnLocalEnTgDelay, appnLocalEnTgUsr1, appnLocalEnTgUsr2, appnLocalEnTgUsr3 Expires October 01, 1996 [Page 115] Internet Draft SNANAU APPN MIB April 1996 } STATUS current DESCRIPTION "The appnLocalEnTopoConfGroup is mandatory only for network nodes." ::= { appnGroups 10 } appnLocalDirPerfConfGroup OBJECT-GROUP OBJECTS { appnDirMaxCaches, appnDirCurCaches, appnDirCurHomeEntries, appnDirRegEntries, appnDirInLocates, appnDirInBcastLocates, appnDirOutLocates, appnDirOutBcastLocates, appnDirNotFoundLocates, appnDirNotFoundBcastLocates, appnDirLocateOutstands } STATUS current DESCRIPTION "The appnLocalDirPerfConfGroup is mandatory only for network nodes and end nodes." ::= { appnGroups 11 } appnCosConfGroup OBJECT-GROUP OBJECTS { appnCosModeCosName, appnCosTransPriority, appnCosNodeRowWgt, appnCosNodeRowResistMin, appnCosNodeRowResistMax, appnCosNodeRowMinCongestAllow, appnCosNodeRowMaxCongestAllow, appnCosTgRowWgt, appnCosTgRowEffCapMin, appnCosTgRowEffCapMax, appnCosTgRowConnCostMin, appnCosTgRowConnCostMax, appnCosTgRowByteCostMin, appnCosTgRowByteCostMax, appnCosTgRowSecurityMin, appnCosTgRowSecurityMax, appnCosTgRowDelayMin, Expires October 01, 1996 [Page 116] Internet Draft SNANAU APPN MIB April 1996 appnCosTgRowDelayMax, appnCosTgRowUsr1Min, appnCosTgRowUsr1Max, appnCosTgRowUsr2Min, appnCosTgRowUsr2Max, appnCosTgRowUsr3Min, appnCosTgRowUsr3Max } STATUS current DESCRIPTION "The appnCosConfGroup is mandatory only for network nodes and end nodes." ::= { appnGroups 12 } appnIntSessConfGroup OBJECT-GROUP OBJECTS { appnIsInGlobeCtrAdminStatus, appnIsInGlobeCtrOperStatus, appnIsInGlobeCtrStatusTime, appnIsInGlobeRscv, appnIsInGlobeRscvTime, appnIsInGlobeActSess, appnIsInSessState, appnIsInPriLuName, appnIsInSecLuName, appnIsInModeName, appnIsInCosName, appnIsInTransPriority, appnIsInSessType, appnIsInSessUpTime, appnIsInCtrUpTime, appnIsInP2SFmdPius, appnIsInS2PFmdPius, appnIsInP2SNonFmdPius, appnIsInS2PNonFmdPius, appnIsInP2SFmdBytes, appnIsInS2PFmdBytes, appnIsInP2SNonFmdBytes, appnIsInS2PNonFmdBytes, appnIsInPsAdjCpName, appnIsInPsAdjTgNum, appnIsInPsSendMaxBtuSize, appnIsInPsSendPacingType, appnIsInPsSendRpc, appnIsInPsSendNxWndwSize, appnIsInPsRecvPacingType, Expires October 01, 1996 [Page 117] Internet Draft SNANAU APPN MIB April 1996 appnIsInPsRecvRpc, appnIsInPsRecvNxWndwSize, appnIsInSsAdjCpName, appnIsInSsAdjTgNum, appnIsInSsSendMaxBtuSize, appnIsInSsSendPacingType, appnIsInSsSendRpc, appnIsInSsSendNxWndwSize, appnIsInSsRecvPacingType, appnIsInSsRecvRpc, appnIsInSsRecvNxWndwSize, appnIsInRouteInfo } STATUS current DESCRIPTION "The appnIntSessConfGroup is mandatory only for network nodes." ::= { appnGroups 13 } appnHprBaseConfGroup OBJECT-GROUP OBJECTS { appnNodeHprIntRteSetups, appnNodeHprIntRteRejects, appnLsErrRecoSup, appnLsForAnrLabel, appnLsRevAnrLabel } STATUS current DESCRIPTION "The appnHprBaseConfGroup is mandatory only for nodes that implement the HPR base (APPN option set 1400)." ::= { appnGroups 14 } appnHprRtpConfGroup OBJECT-GROUP OBJECTS { appnNodeMaxSessPerRtpConn, appnNodeHprOrgRteSetups, appnNodeHprOrgRteRejects, appnNodeHprEndRteSetups, appnNodeHprEndRteRejects, appnLsBfNceId } STATUS current DESCRIPTION "The appnHprRtpConfGroup is mandatory only for Expires October 01, 1996 [Page 118] Internet Draft SNANAU APPN MIB April 1996 nodes that implement the HPR RTP tower (APPN option set 1401)." ::= { appnGroups 15 } appnHprCtrlFlowsRtpConfGroup OBJECT-GROUP OBJECTS { appnLsCpCpNceId, appnLsRouteNceId } STATUS current DESCRIPTION "The appnHprCtrlFlowsRtpConfGroup is mandatory only for nodes that implement the HPR Control Flows over RTP tower (APPN option set 1402)." ::= { appnGroups 16 } appnHprBfConfGroup OBJECT-GROUP OBJECTS { appnIsInGlobeHprBfActSess, appnIsInRtpNceId, appnIsInRtpTcid, appnIsRtpSessions } STATUS current DESCRIPTION "The appnHprBfConfGroup is mandatory only for nodes that implement the APPN/HPR boundary function." ::= { appnGroups 17 } appnTrapConfGroup OBJECT-GROUP OBJECTS { alertIdNumber, affectedObject } STATUS current DESCRIPTION "The appnTrapConfGroup is optional for all groups." ::= { appnGroups 18 } END Expires October 01, 1996 [Page 119] Internet Draft SNANAU APPN MIB April 1996 6. Acknowledgments This MIB module is the product of the IETF SNA NAU MIB WG and the AIW APPN/HPR MIBs SIG. Thanks to Wayne Clark, Cisco Systems; Jim Cobban, Nortel; Rich Daugherty, IBM Corporation; Mark Regan, Cisco Systems; and Leo Temoshenko, IBM Corporation, for their contributions and review. 7. References [1] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure of Management Information for version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1902, January 1996. [2] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual Conventions for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1903, January 1996. [3] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Conformance Statements for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1904, January 1996. [4] IBM, Systems Network Architecture Technical Overview, GC30-3073. [5] IBM, Systems Network Architecture APPN Architecture Reference, SC30-3422 [6] IBM, Systems Network Architecture Formats, SC30-3346. [7] Allen, M., Clouston, B., Kielczewski, Z., Kwan, W., and B. Moore, "Definition of Managed Objects for APPC", Wall Data Inc., Cisco Systems, Jupiter Technology Inc., IBM Corporation, December 1995. [8] Kielczewski, Z., Kostick D., and K. Shih, "Definition of Managed Objects for SNA NAUs using SMIv2", RFC 1666, Eicon Technology Corporation, Bell Communications Research, Novell, August 1994. [9] __, APPN-DLUR-MIB, IBM Corporation [10] Clouston, B., and B. Moore, HPR-MIB, August 1995. [11] SNA DLC Services MIB Working Group, Hilgeman, J., Nix, S., Bartky, A., and W. Clark, "Definitions of Managed Objects for SNA Data Link Control (SDLC) using SMIv2", RFC 1747, January 1995. URL: Expires October 01, 1996 [Page 120] Internet Draft SNANAU APPN MIB April 1996 ftp://ds.internic.net/rfc/rfc1747.txt [12] SNA DLC Services MIB Working Group, Berl, S., Nix, S., and W. Clark, "Definitions of Managed Objects for SNA Data Link Control: LLC", May 1995. [13] Chen, D., Gayek, P., and S. Nix, "Definitions of Managed Objects for Data Link Switching using SNMPv2", October 1995. Expires October 01, 1996 [Page 121] Internet Draft SNANAU APPN MIB April 1996 8. Security Considerations Security issues are not discussed in this memo. 9. Authors' Addresses Bob Clouston Cisco Systems 7025 Kit Creek Road P.O. Box 14987 Research Triangle Park, NC 27709, USA Tel: 1 919 472 2333 E-mail: clouston@cisco.com Bob Moore IBM Corporation 800 Park Offices Drive CNMA/664 P.O. Box 12195 Research Triangle Park, NC 27709, USA Tel: 1 919 254 4436 E-mail: remoore@ralvm6.vnet.ibm.com Expires October 01, 1996 [Page 122] Internet Draft SNANAU APPN MIB April 1996 10. Table of Contents 1. Status of this Memo .................................... 1 2. Introduction ........................................... 1 3. The SNMP Network Management Framework .................. 2 4. Overview ............................................... 2 4.1 APPN MIB structure .................................... 5 5. Definitions ............................................ 9 6. Acknowledgments ........................................ 120 7. References ............................................. 120 8. Security Considerations ................................ 122 9. Author's Addresses ...................................... 122 Expires October 01, 1996 [Page 123]