464XLAT/MAT-T OptimizationThe IPv6 CompanyMolino de la Navata, 75La Navata - GalapagarMadrid28420Spainjordi.palet@theipv6company.comhttp://www.theipv6company.com/TelecentroArgentinaadegidio@telecentro.net.arv6ops
IPv6, DNSSEC, NAT64, DNS64, 464XLAT, MAP-T, CDN, Cache, Optimization
IP/ICMP Translation Algorithm (SIIT) can be used to
provide access for IPv4-only hosts or applications to
IPv4-only or dual-stack destinations over IPv6-only
infrastructure. In that case, the traffic flows are
translated twice: first from IPv4 to IPv6 (stateless
NAT46 at the ingress point to the IPv6-only infrastructure)
and then from IPv6 back to IPv4 (stateful NAT64,
at the egress point). When the destination is IPv6-enabled,
the second translation might be avoided. This document
describes a possible optimization to 464XLAT and MAP-T
to avoid translating IPv6 flows back to IPv4 if the
destination is reachable over IPv6. The proposed solution
would significantly reduce the NAT64 utilization in
the operator's network, increasing the performance.Different transition mechanisms, typically in the group of the so-called
IPv6-only with IPv4aaS (IPv4-as-a-Service), such as 464XLAT ()
or MAP-T (), allow IPv4-only hosts or applications to
connect with IPv4 services in Internet over IPv6-only infrastructure,
by means of a stateless NAT46 SIIT
(IP/ICMP Translation Algorithm) as described by .This is done by the implementation of SIIT at the CE (Customer Edge) Router
or sometimes at the end-device, for example, the UE (User Equipment) in cellular
networks. This functionality is the CLAT (Customer Translator)
in the case of 464XLAT, while in the case of MAP-T is called NAT46.The NAT46/CLAT (WAN side) is connected by IPv6-only to the operator network,
which in turn, will have a reverse translation, the NAT64 (),
known as PLAT (Provider Translator) in the case of 464XLAT. This allows to
translate the IPv6 flow back to IPv4, in order to forward it to Internet.In both cases (NAT46 and NAT64), the translation of the packet headers
is done using the IP/ICMP translation algorithm defined in .
Translation between IPv4 and IPv6 addresses is done as per .
The NAT64 prefix should be discovered by the CE by one or more of the existing
mechanisms (,
or ), and sometimes it is pre-configured at
the CE to the WKP.The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP14
when, and only when, they appear in all capitals, as shown here.In the case of 464XLAT, a DNS64 () is (optionally)
in charge of the synthesis of AAAA records from the A records,
so the NAT64 can be used without the need of doing a double-translation
by means of the NAT46/CLAT.However, the DNS64 is not useful for the IPv4-only hosts or
applications in the LANs, as they will not be able to use the AAAA records,
so they are always forced to use the double-translation.This is the expected behavior, as the original design of NAT64 was
targeted to connect IPv6-only devices (using DNS) to IPv4-only services.
464XLAT expanded the solution to also allow IPv4-only devices
(even if not using DNS) to connect to IPv4-only services by means of
IPv6-only access networks.The optimization solutions presented by this document try to avoid
this double-translation, in the cases when the Internet services,
are already IPv6-enabled. So, in those cases, if the NAT46 already translated
the IPv4 flow to IPv6, it doesn't look necessary to translate this
back to IPv4.A typical 464XLAT deployment is depicted in .Examples of a topology shown on the above picture includes:An IPv6-only residential access network where the CE Router
(with NAT46/CLAT) supports Dual-Stack in the customer LANs.An IPv6-only cellular network where a UE uses the NAT46/CLAT
for dual-stack internal applications and other hosts connected
via tethering.If the operator is providing direct access, for example,
to Content Delivery Networks (CDNs), caches, or other resources,
and they are dual-stacked, the situation can be described as shown in
.In this case if the flows initiated in the LANs come from
IPv4-only hosts or applications, even if the destination resources
are IPv6-enabled, the double-translation is enforced,
which has the following consequences:More traffic needs to pass thru the NAT64 devices.More NAT64 devices may be needed to handle the additional traffic.Additional usage of IPv4 addresses.Additional state at the NAT64 devices.Additional logging, its relevant storage and processing resources.Increasing of delay and reduction of traffic performance.Unnecessary point(s) of failure for that traffic.Clearly, all those aspects have impact in both, CapEx and OpEx.
This is extremely important when considering that most of the time,
the contents stored in CDNs, caches, and so on, is there for a good
reason: It is frequently accessed resources and/or big. Examples such
as video, audio, software and updates, are very common. So, this
optimization can be highly impacting in many networks.If the hosts or applications in the customer LAN are IPv6-capable,
then the access to the CDNs, caches or other resources, will be made
in an optimized way, by means of IPv6-only, not using the NAT64,
as depicted in
.However, if the hosts or applications are IPv4-only, for example,
many SmartTVs and Set-Top-Boxes available today, a non-optimal
double translation will occur (NAT46 at the CLAT and NAT64 at the PLAT),
as illustrated in .Clearly, this is a non-optimal situation, as it means that even if
there is a dual-stack service, the NAT46/CLAT translated IPv4 to IPv6 traffic
flow, is unnecessarily translated back to IPv4, traversing the stateful
NAT64. This has a direct impact in the need to scale the NAT64 beyond
what will be actually needed, if possible solutions, in order to keep
using the IPv6 path towards those services, are considered.As shown in the , this is
also the case for many other services, not just CDNs or caches,
such as VoIP access to the relevant operator infrastructure,
which may be also dual-stack. This is true as well for many other
dual-stack or IPv6-enabled services, which may be directly reachable
from the operator infrastructure, even if they are not part of it,
for example peering agreements, services in IXs, etc. In general,
this will become a more frequent situation for many other services,
which are not yet dual-stack.Moreover, it is already well-known that many CDN/caches, already offer
in case of IPv4 via CGN, routing mechanisms so the private IPv4 addresses
behing the CGN can access access directly the CDN/caches without
requiring the CGN translation. That means that IPv6-only with IPv4aaS
solutions are in a clear disadvantage without the optimization as suggested
in this document.For simplicity, across the rest of this document, references to
CDNs/caches, should be understood, unless otherwise stated, as any
dual-stacked resources.This document looks into different possible solution approaches in order
to optimize the IPv4-only SIIT translation providing a direct path to
IPv6-capable services, as depicted in .Because the IPv4-only devices will not be able to query for AAAA records,
the NAT46/CLAT/CE will translate the IPv4 addresses from the A record for the
CDN/cache destination, using the WKP or NSP, as configured by the operator.If the CDN/cache provider is able to configure, in the relevant interfaces
of the CDN/caches, the same IPv6 addresses that will naturally result as the
translated destination addresses for the queried A records,
preceded by the WKP or NSP, then having more specific routing prefixes,
will result in traffic to those destinations being directly forwarded
towards those interfaces, instead of needing to traverse the NAT64.For example, let's suppose a provider using the WKP (64:ff9b::/96) and a
SmartTV querying for www.example.com:Note: Examples using text representation as per Section 2.3 of
and IPv4 documentation addresses following .It should be remarked that this approach requires that the path
to the destination is configured in such way (i.e., more specific routing prefixes),
that doesn't traverse the NAT64 devices.Because the WKP is non-routable, this solution will only be possible if the
CDN/cache is in the same ASN as the provider network, or somehow interconnected
without routing thru Internet.This solution has the additional drawback of the operational
complexity/issues added to the operation of the CDN/cache,
and the need to synchronize any IPv4 interface address changes
with the relevant IPv6 ones, and possibly with routing.If the NAT46/CLAT/CE, as commonly is the case, is also a DNS proxy/stub
resolver, it is possible to modify the behavior and create an "internal"
interaction among both of them.This approach uses the existing IPv4 and IPv6
addresses in the A and AAAA records, respectively, so no additional
complexity/issues added to the CDN/caches operations.The following sub-sections detail this approach and provide
a step-by-step example case.This optimization MUST be enabled by default, but only when the
WAN link is IPv6-only and the NAT46/CLAT is being used. Note that the
NAT64/CLAT can only be used if the NAT64 prefix has been discovered.
This allows the users to get CEs from the retail and take advantage of
the optimization, without requiring any configuration.The CE MUST support a way to completely disable the optimization,
in order to allow the operator to turn it off in case it is required.It is expected as well, that the NAT64/CLAT is only enabled
if the WAN link is IPv6-only.The goal is to ensure that only IPv4-only hosts are optimized.
Towards that, the CE MUST use ARP and ND (and their relevant caches, if
the information of a hosts has been already learnt) each time a new
host starts a connection. If it is possible to bind the same MAC
address to both an IPv4 and IPv6 address, then the host is not IPv4-only
(it may be IPv6-only or dual-stack), and MUST NOT be optimized.The CE MUST maintain a table of IPv4-only hosts and ensure that if any
IPv4-only hosts become IPv6-enabled, it is properly handled.This mechanism to detect IPv4-only hosts has two drawbacks:If a subscriber has intermediate dual-stack routers in between
the IPv4-only host and the NAT46/CLAT, the IPv4-only hosts will be detected
as dual-stack, so no optimization will be performed. This is not the most
common scenario, as typically the devices that are more relevant to the
optimization (in terms of those that generate more IPv4-only traffic) are
directly attached to the CE, or in bridged interfaces.If a host is dual-stack, but has some IPv4-only applications, because the host
will be detected as dual-stack, none of the applications will be optimized.
This is a good trade-off, considering the most important traffic to optimize
is typically coming from real IPv4-only devices such as old SmartTVs/STBs.
Furthermore, this avoid breaking other mechanisms present only in dual-stack
hosts, such as Happy Eyeballs and simplifies
troubleshooting.It needs to be remarked that, if the detection of the IPv4-only host
is done incorrectly (either not detecting it or by a false detection),
the goal is that no harm is caused. In the worst case,
optimization MUST NOT be performed.In the case of an IPv4-only detected host,
the DNS proxy/stub resolver MUST actually perform an additional
AAAA query, unless the information is already present in the
Additional Section, as per Section 3 of .Note that the NAT46/CLAT MUST already know the WKP or NSP being used in
that network. If the response contains at least one IPv6 address not using
the WKP/NSP, it means that the destination is IPv6-enabled
(because at least one of the IPv6 addresses is not synthesized). This
means that it is possible for the NAT46/CLAT, to create an
Explicit Address Mapping ().In the case of an IPv4-only detected host, the CE DNS proxy MUST only
return the answer to an A query once any of the following happens:An answer to the AAAA query has been received.A SERVFAIL has been received.The "Resolution Delay" has passed.The Resolution Delay MUST be set to the same value (50 milliseconds)
as indicated by Happy Eyeballs .An EAM Table (EAMT used for short, across the rest of this document)
MUST be created/maintained automatically by the NAT46/CLAT,
which is responsible to prioritize any available entries in the EAMT,
versus the use of any synthetic AAAA.The EAMT entry MUST only be created if all the following conditions are met:There is not already EAMT entry for the same pair of MAC/destination IPv4 address/prefix.The source host is IPv4-only.The DNS proxy is ready to return the A answer (according to
).There is at least one non-synthesized AAAA response.If DNSSEC is available, the response has been locally validated
or the AD bit has been set by a trusted resolver, as per .This avoids a slight NAT64 overload and flapping between
destination addresses (IPv4/IPv6), which may impact some applications,
at the cost of a small extra delay for the initial communication setup,
when the EAMT entry doesn't yet exist.Each EAMT entry MUST contain, the fields already described
in and a few new extensions (as per
section 3.1 of ):ID: EAMT Entry Index (optional).MAC address: Identify the host to which this EAMT entry belongs.Destination IPv4 address/prefix: By default, the prefix length is 32 bits.Destination IPv6 address/prefix: By default, the prefix length is 128 bits.
Only non-synthesized addresses are allowed.TTL: It MUST be set to the minimum value from the AAAA/A RR pair.
In normal conditions the TTL for both A and AAAA records, of a given FQDN,
should be the same, so this ensures a proper behavior if there is any DNS mismatch.FQDN: The one that originated the A query for this EAMT entry.
Required in order to ensure a correct detection of cases such as
the use of reverse-proxy with a single IPv4 address to multiple
IPv6 addresses.Valid/Stale/Invalid: When set to Stale, means that this EAMT entry MUST NOT
be used for new connections. When set to Invalid, means that this EAMT entry
can be deleted, unless the Auto/Static bit is also set.Auto/Static: When set to 1, means that this EAMT entry has been
manually/statically configured, for example by means of an explicit
configuration (GUI, CLI, provisioning system, etc.).Note that allowing destination IPv4 and IPv6 prefixes, together with the
Valid/Stale/Invalid and Auto/Static flags, allows manual explicit optimization
and non-optimization configuration for specific parts of Internet.When a new EAMT entry is first automatically created,
it is flagged as "Valid" and "Auto".
If a subsequent A query, with a different FQDN,
results in an IPv4 address that has already an EAMT entry and a
different IPv6 address, it means that some reverse-proxy or similar
functionality is being used by the IPv6-enabled service.
In this case, the existing EAMT entry will be marked as "Stale".
No new EAMT entry is created for that IPv4 address. Otherwise,
the optimization will only allow to access the first set of IPv4/IPv6/FQDN,
which may break the access to other FQDN that share the same IPv4 address
and different IPv6 addresses.In this case the EAMT entry will still become "Invalid" according the TTL, which
allows to re-enable optimization if a new query for the A record has changed
the situation. For example, maybe the reverse-proxy has been removed,
or there is now only a single app using it, so at the time being,
the optimization is again possible without creating troubles to other hosts.An EAMT entry marked as "Stale" or "Invalid", only affects the
relevant host. Other hosts may have their own EAMT entries or they are using
the regular NAT46/CLAT+NAT64 path (without the optimization).Following this approach, if there is a valid EAMT entry, for a given pair
of source-MAC-address/IPv4-destination, the IPv6-native path pointed by the
IPv6 address of that EAMT entry, will take precedence versus the NAT64 path,
so the traffic will not be forwarded to the NAT64.However, this is not sufficient to ensure that individual applications
are able to keep existing connections. In many cases, audio and video
streaming may use a single TCP connection lasting from minutes to hours.
Instead, the CDN TTLs may be configured in the range from 10 to 300 seconds
in order to allow new resolutions to switch quickly and to handle large
recursive resolvers (with hundreds of thousands of clients behind them).Consequently, the EAMT entries MUST NOT be used directly to establish
a forwarding path, but instead, MUST be used to create a stateful NAT entry for
the 4-tuple for the duration of the session/connection. This means that
to implement the optimization the NAT46 MUST be stateful. Typically, stateful
NAT46 are implemented by means of a stateful NAT44 (which often
maybe hardware off-loaded), followed by a stateless NAT46. If the SoC/code
is able to do stateless NAT46, this still could be used when the optimization
is disabled.An EATM entry with the Auto/Static bit set, MUST NOT be automatically
modified.An EAMT entry with the Auto/Static bit clear, MUST be set to Stale in case of:TTL time-out.Or the conditions for creation of the EAMT entry ()
aren't longer met.Entries in Stale state MUST be set to Invalid once existing
connections time-out.The Invalid EAMT entries MUST be deleted, unless the Auto/Static bit is set.
This allows users/operators to set explicit rules for diagnostics or
resolution of issues in special situations.Using the same example as in the previous approach:The following is an example of the CE behavior after the previous case
has already created an EAMT entry and a reverse-proxy is detected:A query for www.example.net A RR is receivedwww.example.net A 192.0.2.1www.example.net AAAA 2001:db8::e:e:f:fA conflict has been detectedThe existing EAMT entry for 192.0.2.1 is set to StaleIf multiple A/AAAA RRs are available, any of them
could be chosen and the optimization will not present
any different result to the hosts compared with a situation where
the optimization is not used.Existing DNS proxy/stub resolvers already implement mechanisms
for DNS Load Balancing (). This don't need to
be modified to implement the optimization if some degree of randomness
is already secured.To secure sufficient randomness, a possible algorithm shall ensure
that different EAMT entries (for different hosts) are permuted randomly
among different A/AAAA records on the A/AAAA RR set.464XLAT can be deployed/used with and without a DNS64.
However, as indicated in ,
the EAMT entry is only created when the service is IPv6-enabled,
because the optimization is only relevant for destinations which
already have AAAA records. In those cases DNS64 is not relevant.Because the EAMT entries are only created when the NAT46/CLAT/CE
proxy/stub DNS is being used, any hosts or applications that don't
use DNS, will not create the relevant entries.They will not be optimized unless EAMT entries are statically
configured.Hosts or applications may use DNS servers from other networks.
For a complete description of reasons for that, refer to
Section 4.4 of .
In the case the DNS is modified, or some hosts or applications
use other DNS servers, the possible scenarios and the implications are:Devices configured to use a DNS proxy/resolver
which is not the CE/NAT46/CLAT (as it is the case for some
consumer electronics). In this case this optimization
will not work, because the EAMT entry will not be created based
on their own flows. Nevertheless, the EAMT entry may be manually
created. However, the lack of EAMT entry, will not impact negatively
in the user’s hosts/applications (the optimization is not performed).
It should be noticed that users commonly, don't change the
configuration of devices such as SmartTVs or STBs
(if they do, some other functionalities, such as CDN/caches
optimizations may not work as well), so this only happens
typically if the vendor is doing it on-purpose
and for good well-known reasons.DNS privacy/encryption. Hosts or applications that use
mechanisms for DNS privacy/encryption, such as DoT
(, ),
DoH () or DoQ
(), will not make use
of the stub/proxy resolver, so the same considerations as
for the previous case applies.Users that modify the DNS in their Operating Systems.
This is quite frequent, however commonly Operating Systems
are dual-stack, so aren't part of the problem statement
described by this document and will not be adversely affected.Users that modify the DNS in the CE. This is less common.
In this case, this optimization is not adversely affected,
because it doesn't depend on the operator DNS, it works only
based on the internal CE interaction between the NAT46/CLAT
and the stub/proxy resolver. Note that it may be affected
if the operator offers different "DNS views" or "split DNS",
however this is not related to this optimization and will
anyway impact in the other possible operator optimizations
(i.e. CDN/cache features).Combinations of the above ones. No further impact is
observed, beyond the ones already described.If a dual-stack host is being detected as IPv4-only, is because it is
not responding to the CE ND messages, so by all means, should be considered,
at the time being, as IPv4-only, and consequently EAMT entries will be
created and traffic will be optimized for IPv4 flows.However, if this hosts suddenly become IPv6-enabled (or dual-stack), the
relevant EAMT entries must be flagged by the CE as "Stale". The host will
be able to complete the connections and the entries will be marked as "Invalid"
and deleted.Anyway, those EAMT entries, while "Valid", may not be actually used by
the dual-stack hosts, because those hosts or applications should prefer IPv6,
so most probably was either a temporary failure or done on-purpose
(user, troubleshooting). If the host is preferring IPv4 for connecting to the
CDN/cache or IPv6-enabled service, it will be actually using the
NAT46/CLAT, including the EAMT entry and consequently IPv6,
so this mechanism will be correcting an undesirable behavior.
This may be also a special case, which actually seems to be an
incoherent host or application implementation.Happy Eyeballs is only enabled in dual-stack hosts.
Consequently, it is not affected by this optimization because both, as the
host should not be detected as IPv4-only, following .If Happy Eyeballs triggers a fallback to IPv4 for a given host, it will be
actually using IPv4 without the optimization, which in turn, uses the IPv6-only
WAN link of the NAT46/CLAT/CE. So even if Happy Eyeballs is present, IPv4 is expected
to be slower than native IPv6 itself due to delays added by the
NAT46/CLAT+NAT64 translations. This optimization reduces those delays by
eliminating the second translation (NAT64) for IPv4-only detected hosts.However, there may be cases where this may be understood as problematic.
The possible reasons why Happy Eyeballs may trigger an IPv4 fallback, in the
case of IPv6-only access networks with IPv4aaS, in general, can be classified as:Failure at the CE or customer LANs. It may happen that the CE or other devices
in the customer LANs are showing erratic behaviors or malfunctions. It is difficult
to believe that this happens only with IPv6, and if that's the case Happy Eyeballs
will not resolve the issue, because IPv4 is provided as a service on top of IPv6.Complete failure of the IPv6-only link or IPv6-only operator's infrastructure
(up to the NAT64). In this case, IPv4 will not work for that subscriber. Happy Eyeballs
will not resolve the issue, and instead will only be adding some extra delay
(the attempt to fallback to IPv4 before timing-out).Complete failure of both IPv4 and IPv6 links behind the operator's NAT64 towards
the destination. In this case, typically both, IPv4 and IPv6 will fail (in many
cases, they are dual-stack links, not different links). Again, Happy Eyeballs
will also fail to resolve the issue.Complete failure only in the IPv6 links behind the operator's NAT64 towards
the destination. This is less frequent, bus still miss-configured AAAA RRs, or
diverse paths for IPv4 and IPv6 together with outages or IPv6-only routing issues,
could generate this problem. In this case, Happy Eyeballs could resolve the issue,
however. It will work because the optimization is not enabled for dual-stack hosts.Partial failure: Slower IPv6 vs IPv4 path end-to-end. In general, the added
delay of the IPv4 translations and NATs across the path, increases the chances that
IPv4 is slower than IPv6. However, it may happen that there is some IPv6 specific
link congestion or packet dropping, that generates the reverse situation, so IPv4
become faster than IPv6. Because the optimization is not being used for dual-stack
hosts, Happy Eyeballs will be resolving the issue.In summary, the optimization will not change the Happy Eyeballs behaviour.
Furthermore, it should be observed that IPv6 failures will also impact other
operators (even if not using the optimization), and especially those using
only NAT64+DNS64 instead of 464XLAT, or even more, any IPv6-only hosts and
applications in any operator network across the entire Internet.
It looks like it is very important to make sure that, as
IPv6 is more prevalent, there is a better monitoring and failures are detected
ASAP, instead of being hidden by Happy Eyeballs, specially in IPv6-only networks.
It should be noticed also that in IPv6-only with IPv4aaS, the chances of
troubles in the IPv4 paths seem to be higher than in the IPv6,
as there are more translations, more devices, more delays,
while the optimization will precisely reduce them.When there is a need to troubleshoot IPv4 from the CE
LANs, it may happen that there is an EAMT entry forcing the flow
to a given destination(s) to use IPv6, which will distort the results,
unless the host being used is dual-stack (which is the most common situation).This can be avoided, using a CLI/GUI or provisioning procedure, to
either completely disable the optimization during the troubleshooting,
or create specific static EAMT entries, using the Valid/Stale/Invalid and
Auto/Static flags, as described in .Consequently, the CE MUST allow both, disabling the optimization
and the setup of manual/static EAMT entries.Instead of using the DNS proxy/stub resolver to create the EAMT entries,
the operator may push this table (or parts of it) into the CE/NAT46/CLAT, by using
configuration/management mechanisms.This solution has the advantage of not being affected by any DNS changes
from the user (the EAMT is created by the operator) and ensures a complete
control from the operator. However, it may impact the cases of devices with
a DNS configured by the vendor.In general, most of the considerations from the previous approach
will apply.One more advantage of this solution is that the EAMT pairs doesn't need
to match the "real" IPv4/IPv6 addresses available in the A/AAAA records, as shown
in the next example.EAMT may contain TTLs which probably are derived from DNS ones,
or alternatively, a global TTL for the full table.An alternative way to configure the table, is that the CE
is actually pulling the table (or parts of it) from the operator
infrastructure. In this case it will be mandatory that the entries
have individual TTLs, again probably derived from the DNS ones.This approach has three major drawbacks:CDNs are used to do frequent changes at the DNS level, so unless the CDNs
offer an API or equivalent convenient solution to keep updated the EAMT,
the operator will need to cache the most frequent FQDNs being resolved
in their own DNS and based on the TTLs, update the EAMT.It requires a new protocol, or an extension to existing ones,
in order to push or pull the EAMT updates.It may generate additional bandwidth utilization in the WAN links
for every CE when the EAMT needs to be update, even when a CE reboots.One of the issues with the IPv6 deployment, is that those services
which become IPv6-only in Internet, aren't reachable by IPv4-only hosts
and applications. This means that new content providers must support
dual-stack even for new services, even while IPv4 public addresses
aren't available.If NAT46/CLAT/DNS-proxy-EAM approach () is chosen,
it also offers the chance to resolve this issue. This is possible
if IPv6-only services get configured with an A resource record pointing to a
well-known IPv4 address despite they aren't actually connected to IPv4.
This is out of scope for this document, as it will require further work
and a reservation by IANA,
This will mean that those services will work fine if there is a NAT46/CLAT
supporting the optimization. This A RR has no negative impact if the NAT46/CLAT
doesn't exist, or it is not optimized, because is not reachable via IPv4-only,
so is not a different situation compared with not having an A RR.The result of this is equivalent to the approach taken by MAP-T
(Section 12.3 of ). However, it has the advantage
that the MAP-T approach is restricted to services in the MAP-T domain.In fact, it may become an incentive for the IPv6 deployment in Internet
services, as it provides the option to use a well-known IPv4 address
(maybe anycast) for the "non-valid" A RR, that points, in case of port 80/443
to a web page or service that returns a warning such as
"This service is only available if the network is
properly connected to Internet with IPv6".NAT46/CLAT/DNS-proxy-EAM approach () seems
the right solution for optimizing the access to dual-stack services, whether
they are located inside or outside the ISP. It is also the only approach which
has no additional requirements for the network operators
(both ISPs and CDN/cache operators).Having this type of optimization facilitates and increases the usage of
IPv6, even for IPv4-only hosts and applications, at the same time that
decreases the use of the NAT64.SIIT already has a SHOULD for EAM support, so it is not a high
additional burden the support required for existing implementations to be
updated for this optimization.This document does not have any new specific security considerations,
besides the ones already known for DNS64.Spoofed DNS responses could generate incorrect EAMT entries. However,
this seems not different than if the optimization is not in place and the
spoofed DNS responses are cached by the CE DNS proxy/stub resolver or
even by hosts in the CE LANs. It very much depends on how and where the
attack is actually performed.In both cases, 464XLAT and MAP-T, the CE device should contain a
DNS proxy/stub resolver, which is also required for the optimization.
Nevertheless, it is common that the user change
DNS settings. If it happens, in the case of MAP-T, the port-set is restricted
for an efficient public IPv4 address sharing, so the entropy of the source
ports is significantly lowered. In this case, theoretically MAP-T is
less resilient against cache poisoning () compared
with 464XLAT. However, an efficient cache poisoning attack requires that
the subscriber operates its own caching DNS server and the attack is
performed in the service provider network, so the chances of a successful
exploitation of this vulnerability are low.This document does not have any new specific IANA considerations.The authors would like to acknowledge the inputs of Erik Nygren,
Fred Baker, Martin Hunek, Chongfeng Xie, Fernando Gont,
Fernando Frediani, Jen Linkova, Eduard Vasilenko and Philip Homburg.