INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 Definitions of Supplemental Managed Objects for the SONET/SDH Interface Type July 1998 Ken Chapman Argon Networks, Inc. 25 Porter Road Littleton, MA 01460 kchapman@argon.com 1. Status of this Memo This document is an Internet Draft. Internet Drafts are working documents of the Internet Engineering Task Force (IETF), its Areas, and its Working Groups. Note that other groups may also distribute working documents as Internet Drafts. Internet Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet Drafts as reference material or to cite them other than as a "work in progress". To learn the current status of any Internet Draft, please check the "1id-abstracts.txt" listing contained in the Internet Drafts Shadow Directories on ftp.ietf.org (US East Coast), nic.nordu.net (Europe), ftp.isi.edu (US West Coast), or munnari.oz.au (Pacific Rim). 2. Abstract This memo defines an experimental portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes supplemental objects used for managing SONET and SDH interfaces. This document is a companion document to the definitions of managed objects and supplemental managed objects for the DS1/E1, DS2/E2, DS3/E3 and SONET/SDH interface types: Expires January 1999 [Page 1] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 [1], [2], [3], [4] and [5]. This MIB is designed to provide support for ASNI T1.231- 1997 [6] standard information not already supported by . Support for this MIB is optional. This memo specifies a MIB module in a manner that is both compliant to the SNMPv2 SMI, and semantically identical to the peer SNMPv1 definitions. This memo does not specify a standard for the Internet community. 3. The SNMP Network Management Framework The SNMP Network Management Framework presently consists of three major components. They are: o the SMI, described in RFC 1902 [7] - the mechanisms used for describing and naming objects for the purpose of management. o the MIB-II, STD 17, RFC 1213 [8] - the core set of managed objects for the Internet suite of protocols. o the protocol, RFC 1157 [9] and/or RFC 1905 [10], - the protocol for accessing managed objects. The Framework permits new objects to be defined for the purpose of experimentation and evaluation. 3.1. Object Definitions Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the subset of Abstract Syntax Notation One (ASN.1) defined in the SMI. In particular, each object type is named by an OBJECT IDENTIFIER, an administratively assigned name. The object type together with an object instance serves to uniquely identify a specific instantiation of the object. For human convenience, we often use a textual string, termed the descriptor, to also refer to the object type. Expires January 1999 [Page 2] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 4. Overview This document supplements . In particular, it supports the following performance monitoring informtion as defined in ASNI T1.231-1997: o Application specific and optional SONET performance primitives and parameters (clause 8). o Previous 1-day register and Recent 1-day registers (clause 9.1.2.1). o Time stamps associated with all registers (clause 9.1.5.1). o Reset of any register(s) (clause 9.1.5.1). o Beginning of day register (clause 9.1.5.1). o Settable thresholds (clause 9.1.5.2). o Settable default thresholds (clause 9.1.5.2). 5. Definitions SONET-Supplemental-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, transmission FROM SNMPv2-SMI TruthValue, DateAndTime FROM SNMPv2-TC OBJECT-GROUP, NOTIFICATION-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB HourOfDay, PerfDayCount FROM PerfHistSup-TC sonetMediumEntry, sonetSectionCurrentEntry, sonetSectionIntervalEntry, sonetLineCurrentEntry, sonetLineIntervalEntry, sonetFarEndLineCurrentEntry, sonetFarEndLineIntervalEntry, sonetPathCurrentEntry, sonetPathIntervalEntry, sonetFarEndPathCurrentEntry, sonetFarEndPathIntervalEntry, sonetVTCurrentEntry, sonetVTIntervalEntry, sonetFarEndVTCurrentEntry, Expires January 1999 [Page 3] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetFarEndVTIntervalEntry FROM SONET-MIB ifIndex FROM IF-MIB; sonetSupplementalMIB MODULE-IDENTITY LAST-UPDATED "9807131752Z" -- 13-Jul-98 1:52 PM EST ORGANIZATION "Argon Networks, Inc." CONTACT-INFO " Ken Chapman Postal: Argon Networks, Inc. 25 Porter Road Littleton, MA 01460 USA Phone: +1 978 486 0665 Fax: +1 978 486 9379 Email: KChapman@Argon.com" DESCRIPTION "This MIB module provides extensions to the SONET-MIB (RFC nnnn) objects. It provides definitions for management information that supports those parts of ANSI T1.231-1997 that are not covered by the SONET-MIB." ::= { transmission xx } -- ********************************************************************* -- Note to RFC editor: Assign a number for xx from IANA when publishing -- this MIB as an RFC. -- ********************************************************************* -- This is the MIB extension module for the SONET objects sonetSupObjects OBJECT IDENTIFIER ::= { sonetSupplementalMIB 1 } sonetSupObjectsPath OBJECT IDENTIFIER ::= { sonetSupplementalMIB 2 } sonetSupObjectsVT OBJECT IDENTIFIER ::= { sonetSupplementalMIB 3 } -- groups in the SONET MIB extension module sonetSupConfig OBJECT IDENTIFIER ::= { sonetSupObjects 1 } sonetSupMedium OBJECT IDENTIFIER ::= { sonetSupObjects 2 } sonetSupSection OBJECT IDENTIFIER ::= { sonetSupObjects 3 } sonetSupLine OBJECT IDENTIFIER ::= { sonetSupObjects 4 } sonetSupFarEndLine OBJECT IDENTIFIER ::= { sonetSupObjects 5 } sonetSupPath OBJECT IDENTIFIER ::= { sonetSupObjectsPath 1 } sonetSupFarEndPath OBJECT IDENTIFIER ::= { sonetSupObjectsPath 2 } sonetSupVT OBJECT IDENTIFIER ::= { sonetSupObjectsVT 1 } sonetSupFarEndVT OBJECT IDENTIFIER ::= { sonetSupObjectsVT 2 } Expires January 1999 [Page 4] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 -- ********************************************************************* -- SONET Configuration group object definitions. -- These objects apply to all SONET interfaces. -- ********************************************************************* sonetResetAllCounters OBJECT-TYPE SYNTAX INTEGER { resetCounters(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this variable to 1 will cause all of the counters (performance regsters) on all of the SONET interfaces in the Network Element (agent) to be initialized to zero (0)." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupConfig 1 } sonetStartOfDay OBJECT-TYPE SYNTAX HourOfDay MAX-ACCESS read-write STATUS current DESCRIPTION "The time of day that marks the beginning of each 1-day interval used in the performance monitoring parameters for all SONET interfaces in the NE. This time is on an hour boundary." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." DEFVAL { '00'H } -- Midnight, local time ::= { sonetSupConfig 2 } sonetThresholdTrapEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2), off(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable indicates whether threshold traps should be generated for SONET interfaces. This setting applies to the entire Network Element. When this variable is in the enabled(1) state, then all traps are enabled; when this variable is in the disabled(2) state, all traps are disabled; when this variable is in the off(3) state then traps are enabled or disabled on a per port basis via the sonetPortThresholdTrapEnable variable." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { off } ::= { sonetSupConfig 3 } Expires January 1999 [Page 5] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 -- ********************************************************************* -- Extension to the sonetMedimTable found in the SONET-MIB. -- ********************************************************************* sonetSupMediumTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSupMediumEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Extensions to the SONET Medium table." ::= { sonetSupMedium 1 } sonetSupMediumEntry OBJECT-TYPE SYNTAX SonetSupMediumEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An extension to an entry in the SONET Medium table." AUGMENTS { sonetMediumEntry } ::= { sonetSupMediumTable 1 } SonetSupMediumEntry ::= SEQUENCE { sonetPortThresholdTrapEnable INTEGER, sonetMediumDayTimeElapsed INTEGER, sonetMediumValidDays INTEGER, sonetMediumInvalidDays INTEGER, sonetMediumResetCounters INTEGER, sonetMediumCurrentStartTime DateAndTime, sonetMediumCurrentLOSSs PerfCurrentCount } sonetPortThresholdTrapEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2), oncePerInterval(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable indicates whether threshold traps should be generated for the SONET port associated with this interface. This variable applies to all of the SONET layers associated with this interface and any Path or VT interfaces which are layered on this interface. This variable is only valid if the sonetThresholdTrapEnable variable is not implemented or is in the off(3) state." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { disabled } ::= { sonetSupMediumEntry 1 } Expires January 1999 [Page 6] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetMediumDayTimeElapsed OBJECT-TYPE SYNTAX INTEGER (0..86409) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds that have elapsed since the beginning of the current 1-day perfromance history interval." ::= { sonetSupMediumEntry 2 } sonetMediumValidDays OBJECT-TYPE SYNTAX INTEGER (0..32) MAX-ACCESS read-only STATUS current DESCRIPTION "The oldest interval number for which data is available. The value will normally be n, where n is the number of intervals supported by this agent. However, some intervals will not be available if the interface was brought online within the last n days, in which case the value will be the number of 1-day intervals since the interface has been online (including the current interval). It is also possible that some intervals are unavailable in the case where the agent is a proxy." ::= { sonetSupMediumEntry 3 } sonetMediumInvalidDays OBJECT-TYPE SYNTAX INTEGER (0..32) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of intervals supported by the agent for which no data is available for the interface." ::= { sonetSupMediumEntry 4 } sonetMediumResetCounters OBJECT-TYPE SYNTAX INTEGER { current15Minute(1), current1day(2), all(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This varible provides the capability to initialize SONET media layer performance counters to zero (0)." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupMediumEntry 5 } Expires January 1999 [Page 7] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetMediumCurrentStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which the current 15-minute interval of physical media measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupMediumEntry 6 } sonetMediumCurrentLOSSs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The physical media loss of signal (LOS) seconds count (LOSS) is the number of 1-second intervals containing one or more loss of signal defects which were encountered by a SONET interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.1." ::= { sonetSupMediumEntry 7 } -- ********************************************************************* -- The 15-minute interval history table for physical media related -- performance prameters. -- ********************************************************************* sonetMediumIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetMediumIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET Medium Interval Table." ::= { sonetSupMedium 2 } sonetMediumIntervalEntry OBJECT-TYPE SYNTAX SonetMediumIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET Medium Interval table." INDEX { ifIndex, sonetMediumIntervalNumber } ::= { sonetMediumIntervalTable 1 } SonetMediumIntervalEntry ::= Expires January 1999 [Page 8] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SEQUENCE { sonetMediumIntervalNumber INTEGER, sonetMediumIntervalStartTime DateAndTime, sonetMediumIntervalValidData TruthValue, sonetMediumIntervalLOSSs PerfIntervalCount } sonetMediumIntervalNumber OBJECT-TYPE SYNTAX INTEGER (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed (previous) 15-minute interval, and the interval identified by n is the interval immediately preceding the one identified by n-1." REFERENCE "ANSI T1.231-1997 clause 9.1.2.1." ::= { sonetMediumIntervalEntry 1 } sonetMediumIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 15 minutes, or (b) some data is missing (e.g., when a near-end defect prevents some far-end data from being collected)." REFERENCE "ANSI T1.231-1997 clause 9.1.2.2." ::= { sonetMediumIntervalEntry 2 } sonetMediumIntervalStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which this 15-minute interval of physical media measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetMediumIntervalEntry 3 } sonetMediumIntervalLOSSs OBJECT-TYPE Expires January 1999 [Page 9] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The physical media loss of signal (LOS) seconds count (LOSS) is the number of 1-second intervals containing one or more loss of signal defects which were encountered by a SONET interface in the 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.1." ::= { sonetMediumIntervalEntry 4 } -- ********************************************************************* -- The 1-day interval history table for physical media related -- perfomance prameters. -- ********************************************************************* sonetMediumDayTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetMediumDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET Medium Interval Table." ::= { sonetSupMedium 3 } sonetMediumDayEntry OBJECT-TYPE SYNTAX SonetMediumDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET Medium Interval table." INDEX { ifIndex, sonetMediumDayNumber } ::= { sonetMediumDayTable 1 } SonetMediumDayEntry ::= SEQUENCE { sonetMediumDayNumber INTEGER, sonetMediumDayStartTime DateAndTime, sonetMediumDayValidData TruthValue, sonetMediumDayLOSSs PerfDayCount } sonetMediumDayNumber OBJECT-TYPE SYNTAX INTEGER (1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION Expires January 1999 [Page 10] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 "A number which identifies the 1-day interval for which the set of physical media related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval." REFERENCE "ANSI T1.231-1997 clause 9.1.2.1." ::= { sonetMediumDayEntry 1 } sonetMediumDayValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is missing (e.g., when a near-end defect prevents some far-end data from being collected)." REFERENCE "ANSI T1.231-1997 clause 9.1.2.2." ::= { sonetMediumDayEntry 2 } sonetMediumDayStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which this 1-day interval of physical media measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetMediumDayEntry 3 } sonetMediumDayLOSSs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The physical media loss of signal (LOS) seconds count (LOSS) is the number of 1-second intervals containing one or more loss of signal defects which were encountered by a SONET interface in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.1." ::= { sonetMediumDayEntry 4 } Expires January 1999 [Page 11] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 -- ********************************************************************* -- SONET Section group object definitions. -- -- SONET Section default threshold value object definitions. -- These default values apply to all section interfaces. -- ********************************************************************* sonetSectionDefaultThresholdTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSectionDefaultThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of default thresholds for SONET section counters." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSupSection 1 } sonetSectionDefaultThresholdEntry OBJECT-TYPE SYNTAX SonetSectionDefaultThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table of default thresholds. The table has a variable for each counter type and accumulation period combination, but uses an index to indetify the digital signal rate. The agent must provide a set of default threshold values for all rates that the NE supports. The agent may make these variables read-only." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." INDEX { sonetSectionDefaultThresholdRate } ::= { sonetSectionDefaultThresholdTable 1 } SonetSectionDefaultThresholdEntry ::= SEQUENCE { sonetSectionDefaultThresholdRate INTEGER, sonetSectionDefaultCVThreshold INTEGER, sonetSectionDefaultESThreshold INTEGER, sonetSectionDefaultESAThreshold INTEGER, sonetSectionDefaultESBThreshold INTEGER, sonetSectionDefaultSESThreshold INTEGER, sonetSectionDefaultSEFSThreshold INTEGER, sonetSectionDefaultDayCVThreshold INTEGER, sonetSectionDefaultDayESThreshold INTEGER, sonetSectionDefaultDayESAThreshold INTEGER, sonetSectionDefaultDayESBThreshold INTEGER, sonetSectionDefaultDaySESThreshold INTEGER, sonetSectionDefaultDaySEFSThreshold INTEGER } Expires January 1999 [Page 12] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetSectionDefaultThresholdRate OBJECT-TYPE SYNTAX INTEGER { oc1(1), oc3(2), oc12(3), oc24(4), oc48(5), oc192(6) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The digital signal rate for which the default threshold values apply." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSectionDefaultThresholdEntry 1 } sonetSectionDefaultCVThreshold OBJECT-TYPE SYNTAX INTEGER (1..16383) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET CV-S counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSectionDefaultThresholdEntry 2 } sonetSectionDefaultESThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ES-S counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSectionDefaultThresholdEntry 3 } sonetSectionDefaultESAThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESA-S counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSectionDefaultThresholdEntry 4 } Expires January 1999 [Page 13] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetSectionDefaultESBThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESB-S counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSectionDefaultThresholdEntry 5 } sonetSectionDefaultSESThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET SES-S counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSectionDefaultThresholdEntry 6 } sonetSectionDefaultSEFSThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET SEFS-S counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSectionDefaultThresholdEntry 7 } sonetSectionDefaultDayCVThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET CV-S counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSectionDefaultThresholdEntry 8 } sonetSectionDefaultDayESThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ES-S counter 15-minute interval thresholds." Expires January 1999 [Page 14] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSectionDefaultThresholdEntry 9 } sonetSectionDefaultDayESAThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESA-S counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSectionDefaultThresholdEntry 10 } sonetSectionDefaultDayESBThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESB-S counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSectionDefaultThresholdEntry 11 } sonetSectionDefaultDaySESThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET SES-S counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSectionDefaultThresholdEntry 12 } sonetSectionDefaultDaySEFSThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET SEFS-S counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSectionDefaultThresholdEntry 13 } -- ********************************************************************* -- SONET Section threshold value object definitions. This table is an -- extension to the sonetSectionCurrentTable found in the SONET-MIB. Expires January 1999 [Page 15] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 -- ********************************************************************* sonetSectionThresholdTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSectionThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of trap threshold values for SONET section counters." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSupSection 2 } sonetSectionThresholdEntry OBJECT-TYPE SYNTAX SonetSectionThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table of SONET Section trap thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." AUGMENTS { sonetSectionCurrentEntry } ::= { sonetSectionThresholdTable 1 } SonetSectionThresholdEntry ::= SEQUENCE { sonetSectionCurrentCVThreshold INTEGER, sonetSectionCurrentESThreshold INTEGER, sonetSectionCurrentESAThreshold INTEGER, sonetSectionCurrentESBThreshold INTEGER, sonetSectionCurrentSESThreshold INTEGER, sonetSectionCurrentSEFSThreshold INTEGER, sonetSectionDayCVThreshold INTEGER, sonetSectionDayESThreshold INTEGER, sonetSectionDayESAThreshold INTEGER, sonetSectionDayESBThreshold INTEGER, sonetSectionDaySESThreshold INTEGER, sonetSectionDaySEFSThreshold INTEGER } sonetSectionCurrentCVThreshold OBJECT-TYPE SYNTAX INTEGER (0..16383) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval CV-S counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } Expires January 1999 [Page 16] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 ::= { sonetSectionThresholdEntry 1 } sonetSectionCurrentESThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval ES-S counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetSectionThresholdEntry 2 } sonetSectionCurrentESAThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval ESA-S counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetSectionThresholdEntry 3 } sonetSectionCurrentESBThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval ESB-S counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetSectionThresholdEntry 4 } sonetSectionCurrentSESThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval SES-S counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." Expires January 1999 [Page 17] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 DEFVAL { 0 } ::= { sonetSectionThresholdEntry 5 } sonetSectionCurrentSEFSThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval SEFS-S counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetSectionThresholdEntry 6 } sonetSectionDayCVThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current day CV-S counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetSectionThresholdEntry 7 } sonetSectionDayESThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current day ES-S counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetSectionThresholdEntry 8 } sonetSectionDayESAThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current day ESA-S counter. A value of zero indicates that the default threshold value is to be used." Expires January 1999 [Page 18] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetSectionThresholdEntry 9 } sonetSectionDayESBThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current day ESB-S counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetSectionThresholdEntry 10 } sonetSectionDaySESThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current day SES-S counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetSectionThresholdEntry 11 } sonetSectionDaySEFSThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current day SEFS-S counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetSectionThresholdEntry 12 } -- ********************************************************************* -- Extensions to the sonetSectionCurrentTable found in the SONET-MIB. -- ********************************************************************* sonetSupSectionCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSupSectionCurrentEntry MAX-ACCESS not-accessible Expires January 1999 [Page 19] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 STATUS current DESCRIPTION "Various extensions to the SONET Section Current table." ::= { sonetSupSection 3 } sonetSupSectionCurrentEntry OBJECT-TYPE SYNTAX SonetSupSectionCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Extensions to an entry in the SONET Section Current table." AUGMENTS { sonetSectionCurrentEntry } ::= { sonetSupSectionCurrentTable 1 } SonetSupSectionCurrentEntry ::= SEQUENCE { sonetSectionSevereErrorThreshold Integer32, sonetSectionResetCounters INTEGER, sonetSectionCurrentStartTime DateAndTime, sonetSectionCurrentESAs PerfCurrentCount, sonetSectionCurrentESBs PerfCurrentCount } sonetSectionSevereErrorThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of section errors in a 1-second interval at which point the condition is counted as a severe error. The value of this variable should correspond to the value indicated by sonetSESthresholdSet in the SONET-MIB. If sonetSESthresholdSet is set to other(1), this variable is the soul source of this information." REFERENCE "ANSI T1.231-1997 clause 8.4.2.5." ::= { sonetSupSectionCurrentEntry 1 } sonetSectionResetCounters OBJECT-TYPE SYNTAX INTEGER { current15Minute(1), current1day(2), all(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This varible provides the capability to initialize SONET Expires January 1999 [Page 20] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 section layer performance counters to zero (0) on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupSectionCurrentEntry 2 } sonetSectionCurrentStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which the current 15-minute interval of section measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupSectionCurrentEntry 3 } sonetSectionCurrentESAs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The section errored second type A (ESA-S) count is the number of 1-second intervals containing one BIP-8 error (B1 byte) and no SEF or LOS defects which were encountered by a SONET interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.2.3." ::= { sonetSupSectionCurrentEntry 4 } sonetSectionCurrentESBs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The section errored second type B (ESB-S) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold BIP-8 errors (B1 byte), and no SEF or LOS defects which were encountered by a SONET interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.2.4." ::= { sonetSupSectionCurrentEntry 5 } -- ******************************************************************* -- Extension to the sonetSectionIntervalTable found in the SONET-MIB. -- ******************************************************************* sonetSupSectionIntervalTable OBJECT-TYPE Expires January 1999 [Page 21] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SYNTAX SEQUENCE OF SonetSupSectionIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The extension to the SONET Section Interval table to add more counters." ::= { sonetSupSection 14 } sonetSupSectionIntervalEntry OBJECT-TYPE SYNTAX SonetSupSectionIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An extension to an entry in the SONET Section Interval table." AUGMENTS { sonetSectionIntervalEntry } ::= { sonetSupSectionIntervalTable 1 } SonetSupSectionIntervalEntry ::= SEQUENCE { sonetSectionIntervalStartTime DateAndTime, sonetSectionIntervalESAs PerfIntervalCount, sonetSectionIntervalESBs PerfIntervalCount } sonetSectionIntervalStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which this 15-minute interval of section measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupSectionIntervalEntry 1 } sonetSectionIntervalESAs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The section errored second type A (ESA-S) count is the number of 1-second intervals containing one BIP-8 error (B1 byte) and no SEF or LOS defects which were encountered by a SONET interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.2.3." ::= { sonetSupSectionIntervalEntry 2 } Expires January 1999 [Page 22] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetSectionIntervalESBs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The section errored second type B (ESB-S) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold BIP-8 errors (B1 byte), and no SEF or LOS defects which were encountered by a SONET interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.2.4." ::= { sonetSupSectionIntervalEntry 3 } -- ********************************************************************* -- The SONET Section Day Table. -- ********************************************************************* sonetSectionDayTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSectionDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET Section Day table. Contains various statistics collected by each SONET Section over multiple 1-day intervals of operation." ::= { sonetSupSection 15 } sonetSectionDayEntry OBJECT-TYPE SYNTAX SonetSectionDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET Section Day table." INDEX { ifIndex, sonetSectionDayNumber } ::= { sonetSectionDayTable 1 } SonetSectionDayEntry ::= SEQUENCE { sonetSectionDayNumber INTEGER, sonetSectionDayStartTime DateAndTime, sonetSectionDayValidData TruthValue, sonetSectionDayCVs PerfDayCount, sonetSectionDayESs PerfDayCount, sonetSectionDayESAs PerfDayCount, sonetSectionDayESBs PerfDayCount, sonetSectionDaySESs PerfDayCount, Expires January 1999 [Page 23] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetSectionDaySEFSs PerfDayCount } sonetSectionDayNumber OBJECT-TYPE SYNTAX INTEGER (1..33) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number which identifies the 1-day interval for which the set of section related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval." REFERENCE "ANSI T1.231-1997 clause 9.1.2.1." ::= { sonetSectionDayEntry 1 } sonetSectionDayStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which this 1-day interval of sections measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSectionDayEntry 2 } sonetSectionDayValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is missing." REFERENCE "ANSI T1.231-1997 clause 9.1.2.2." ::= { sonetSectionDayEntry 3 } sonetSectionDayCVs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION Expires January 1999 [Page 24] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 "The section code violation (CV-S) count is the number of BIP-8 errors which were detected at the SONET section layer interface in a previous 1-day interval. Each section BIP-8 can detect up to eight errors per STS-N frame, with each error incrementing the CV counter. CVs for the section layer are collected using the BIP-8 in the B1 byte located in the section overhead of STS-1 number 1." REFERENCE "ANSI T1.231-1997 clause 8.4.2.1.1." ::= { sonetSectionDayEntry 4 } sonetSectionDayESs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The section errored second (ES-S) count is the number of 1-second intervals containing one or more BIP-8 error (B1 byte), one or more SEF defects, or one or more LOS defects which were encountered by the SONET section layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.2.2." ::= { sonetSectionDayEntry 5 } sonetSectionDayESAs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The section errored second type A (ESA-S) count is the number of 1-second intervals containing one BIP-8 error (B1 byte) and no SEF or LOS defects which were encountered by the SONET section layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.2.3." ::= { sonetSectionDayEntry 6 } sonetSectionDayESBs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The section errored second type B (ESB-S) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold BIP-8 errors (B1 byte), and no SEF or LOS defects which were encountered by the SONET section layer interface in the current 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.2.4." ::= { sonetSectionDayEntry 7 } Expires January 1999 [Page 25] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetSectionDaySESs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The section severely errored second (SES-S) count is the number of 1-second intervals containing sonetSevereErrorThreshold or more BIP-8 errors (B1 byte), one or more SEF defects, or one or more LOS defects which were encountered by the SONET section layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.2.5." ::= { sonetSectionDayEntry 8 } sonetSectionDaySEFSs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The section severely errored frame second (SEFS-S) count is the number of 1-second intervals containing one or more SEF defects which were encountered by the SONET section layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.2.6." ::= { sonetSectionDayEntry 9 } -- ********************************************************************* -- SONET Line group object definitions. -- -- SONET Line default threshold value object definitions. These -- default values apply to both near-end and far-end line interfaces. -- ********************************************************************* sonetLineDefaultThresholdTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetLineDefaultThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of default thresholds for SONET Line counters." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSupLine 1 } sonetLineDefaultThresholdEntry OBJECT-TYPE SYNTAX SonetLineDefaultThresholdEntry MAX-ACCESS not-accessible STATUS current Expires January 1999 [Page 26] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 DESCRIPTION "An entry in the table of default thresholds. The table has a variable for each counter type and accumulation period combination, but uses indexes to indetify the digital signal direction and rate. The agent must provide a set of default threshold values for all rates that the NE supports. The agent may make these variables read-only." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." INDEX { sonetLineDefaultThresholdDirection, sonetLineDefaultThresholdRate } ::= { sonetLineDefaultThresholdTable 1 } SonetLineDefaultThresholdEntry ::= SEQUENCE { sonetLineDefaultThresholdDirection INTEGER, sonetLineDefaultThresholdRate INTEGER, sonetLineDefaultCVThreshold INTEGER, sonetLineDefaultESThreshold INTEGER, sonetLineDefaultESAThreshold INTEGER, sonetLineDefaultESBThreshold INTEGER, sonetLineDefaultSESThreshold INTEGER, sonetLineDefaultAISSThreshold INTEGER, sonetLineDefaultUASThreshold INTEGER, sonetLineDefaultDayCVThreshold INTEGER, sonetLineDefaultDayESThreshold INTEGER, sonetLineDefaultDayESAThreshold INTEGER, sonetLineDefaultDayESBThreshold INTEGER, sonetLineDefaultDaySESThreshold INTEGER, sonetLineDefaultDayAISSThreshold INTEGER, sonetLineDefaultDayUASThreshold INTEGER } sonetLineDefaultThresholdDirection OBJECT-TYPE SYNTAX INTEGER { nearEnd(1), farEnd(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The digital signal direction for which the default threshold values apply." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 1 } sonetLineDefaultThresholdRate OBJECT-TYPE SYNTAX INTEGER { Expires January 1999 [Page 27] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 vt1dot5(1), vtg(2), oc1(3), oc3(4), oc12(5), oc24(6), oc48(7), oc192(8) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The digital signal rate for which the default threshold values apply." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 2 } sonetLineDefaultCVThreshold OBJECT-TYPE SYNTAX INTEGER (1..16383) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET CV-L and CV-LFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 3 } sonetLineDefaultESThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ES-L and ES-LFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 4 } sonetLineDefaultESAThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESA-L and ESA-LFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 5 } Expires January 1999 [Page 28] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetLineDefaultESBThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESB-L and ESB-LFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 6 } sonetLineDefaultSESThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET SES-L and SES-LFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 7 } sonetLineDefaultAISSThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET AISS-L and AISS-LFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 8 } sonetLineDefaultUASThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET UAS-L and UAS-LFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 9 } sonetLineDefaultDayCVThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET CV-L and CV-LFE counter 15-minute interval thresholds." Expires January 1999 [Page 29] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 10 } sonetLineDefaultDayESThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ES-L and ES-LFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 11 } sonetLineDefaultDayESAThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESA-L and ESA-LFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 12 } sonetLineDefaultDayESBThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESB-L and ESB-LFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 13 } sonetLineDefaultDaySESThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET SES-L and SES-LFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 14 } sonetLineDefaultDayAISSThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current Expires January 1999 [Page 30] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 DESCRIPTION "The default value for SONET AISS-L and AISS-LFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 15 } sonetLineDefaultDayUASThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET UAS-L and UAS-LFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetLineDefaultThresholdEntry 16 } -- ********************************************************************* -- SONET Line threshold value object definitions. This table is an -- extension to the sonetLineCurrentTable found in the SONET-MIB. -- ********************************************************************* sonetLineThresholdTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetLineThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of trap threshold values for SONET Line counters." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSupLine 2 } sonetLineThresholdEntry OBJECT-TYPE SYNTAX SonetLineThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table of SONET Line trap thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." AUGMENTS { sonetLineCurrentEntry } ::= { sonetLineThresholdTable 1 } SonetLineThresholdEntry ::= SEQUENCE { sonetLineCurrentCVThreshold INTEGER, sonetLineCurrentESThreshold INTEGER, sonetLineCurrentESAThreshold INTEGER, sonetLineCurrentESBThreshold INTEGER, Expires January 1999 [Page 31] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetLineCurrentSESThreshold INTEGER, sonetLineCurrentAISSThreshold INTEGER, sonetLineCurrentUASThreshold INTEGER, sonetLineDayCVThreshold INTEGER, sonetLineDayESThreshold INTEGER, sonetLineDayESAThreshold INTEGER, sonetLineDayESBThreshold INTEGER, sonetLineDaySESThreshold INTEGER, sonetLineDayAISSThreshold INTEGER, sonetLineDayUASThreshold INTEGER } sonetLineCurrentCVThreshold OBJECT-TYPE SYNTAX INTEGER (0..16383) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval CV-L and CV-LFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetLineThresholdEntry 1 } sonetLineCurrentESThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval ES-L and ES-LFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetLineThresholdEntry 2 } sonetLineCurrentESAThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval ESA-L and ESA-LFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetLineThresholdEntry 3 } Expires January 1999 [Page 32] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetLineCurrentESBThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval ESB-L and ESB-LFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetLineThresholdEntry 4 } sonetLineCurrentSESThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval SES-L and SES-LFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetLineThresholdEntry 5 } sonetLineCurrentAISSThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval AISS-L and AISS-LFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetLineThresholdEntry 6 } sonetLineCurrentUASThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval UAS-L and UAS-LFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetLineThresholdEntry 7 } Expires January 1999 [Page 33] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetLineDayCVThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current day CV-L and CV-LFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetLineThresholdEntry 8 } sonetLineDayESThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current day ES-L and ES-LFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetLineThresholdEntry 9 } sonetLineDayESAThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current day ESA-L and ESA-LFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetLineThresholdEntry 10 } sonetLineDayESBThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current day ESB-L and ESB-LFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetLineThresholdEntry 11 } Expires January 1999 [Page 34] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetLineDaySESThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current day SES-L and SES-LFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetLineThresholdEntry 12 } sonetLineDayAISSThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current day AISS-L and AISS-LFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetLineThresholdEntry 13 } sonetLineDayUASThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current day UAS-L and UAS-LFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetLineThresholdEntry 14 } -- ********************************************************************* -- Extension to the sonetLineCurrentTable found in the SONET-MIB. -- ********************************************************************* sonetSupLineCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSupLineCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Various extension to the SONET Line Current table." ::= { sonetSupLine 3 } Expires January 1999 [Page 35] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetSupLineCurrentEntry OBJECT-TYPE SYNTAX SonetSupLineCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Extensions to an entry in the SONET Line Current table." AUGMENTS { sonetLineCurrentEntry } ::= { sonetSupLineCurrentTable 1 } SonetSupLineCurrentEntry ::= SEQUENCE { sonetLineSevereErrorThreshold Integer32, sonetLineResetCounters INTEGER, sonetLineCurrentStartTime DateAndTime, sonetLineCurrentFCs PerfCurrentCount, sonetLineCurrentESAs PerfCurrentCount, sonetLineCurrentESBs PerfCurrentCount, sonetLineCurrentAISSs PerfCurrentCount } sonetLineSevereErrorThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of line errors in a 1-second interval at which point the condition is counted as a severe error. The value of this variable should correspond to the value indicated by sonetSESthresholdSet in the SONET-MIB. If sonetSESthresholdSet is set to other(1), this variable is the soul source of this information. This value applies to all near-end and far-end line SES counters." REFERENCE "ANSI T1.231-1997 Table 16." ::= { sonetSupLineCurrentEntry 1 } sonetLineResetCounters OBJECT-TYPE SYNTAX INTEGER { nearEndCurrent15Minute(1), nearEndCurrent1day(2), farEndCurrent15Minute(3), farEndCurrent1day(4), all(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "This varible provides the capability to initialize SONET Expires January 1999 [Page 36] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 near-end and far-end line layer performance counters to zero (0) on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupLineCurrentEntry 2 } sonetLineCurrentStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which the current 15-minute interval of near-end line measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupLineCurrentEntry 3 } sonetLineCurrentFCs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The near-end line failure count (FC-L) is the number of occurences of near-end line failure events encountered by the SONET line layer interface in the current 15-minute interval. A near-end line failure event begins when an AIS-L failure is declared; a near-end line failure event ends when the AIS-L failure is cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.7.1." ::= { sonetSupLineCurrentEntry 4 } sonetLineCurrentESAs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The line errored second type A (ESA-L) count is the number of 1-second intervals containing one EDC error (B2 byte) and no AIS-L defects which were encountered by the SONET line layer interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.3.1.3." ::= { sonetSupLineCurrentEntry 5 } sonetLineCurrentESBs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION Expires January 1999 [Page 37] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 "The line errored second type B (ESB-L) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold EDC errors (B2 byte), and no AIS-L defects which were encountered by the SONET line layer interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.3.1.4." ::= { sonetSupLineCurrentEntry 6 } sonetLineCurrentAISSs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The line AIS second (AISS-L) is a count of 1-second intervals containing one or more alarm indication signal (AIS-L) defects which were encountered by the SONET line layer interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.3.1.7." ::= { sonetSupLineCurrentEntry 7 } -- ******************************************************************* -- Extension to the sonetLineIntervalTable found in the SONET-MIB. -- ******************************************************************* sonetSupLineIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSupLineIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The extension to the SONET Line Interval table to add more counters." ::= { sonetSupLine 4 } sonetSupLineIntervalEntry OBJECT-TYPE SYNTAX SonetSupLineIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An extension to an entry in the SONET Line Interval table." AUGMENTS { sonetLineIntervalEntry } ::= { sonetSupLineIntervalTable 1 } SonetSupLineIntervalEntry ::= SEQUENCE { sonetLineIntervalStartTime DateAndTime, Expires January 1999 [Page 38] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetLineIntervalFCs PerfIntervalCount, sonetLineIntervalESAs PerfIntervalCount, sonetLineIntervalESBs PerfIntervalCount, sonetLineIntervalAISSs PerfIntervalCount } sonetLineIntervalStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which this 15-minute interval of measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupLineIntervalEntry 1 } sonetLineIntervalFCs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The near-end line failure count (FC-L) is the number of occurences of near-end line failure events encountered by the SONET line layer interface in a previous 15-minute interval. A near-end line failure event begins when an AIS-L failure is declared; a near-end line failure event ends when the AIS-L failure is cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.7.1." ::= { sonetSupLineIntervalEntry 2 } sonetLineIntervalESAs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The line errored second type A (ESA-L) count is the number of 1-second intervals containing one EDC error (B2 byte) and no AIS-L defects which were encountered by the SONET line layer interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.3.1.3." ::= { sonetSupLineIntervalEntry 3 } sonetLineIntervalESBs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION Expires January 1999 [Page 39] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 "The line errored second type B (ESB-L) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold EDC errors (B2 byte), and no AIS-L defects which were encountered by the SONET line layer interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.3.1.4." ::= { sonetSupLineIntervalEntry 4 } sonetLineIntervalAISSs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The line AIS second (AISS-L) is a count of 1-second intervals containing one or more alarm indication signal (AIS-L) defects which were encountered by the SONET line layer interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.3.1.7." ::= { sonetSupLineIntervalEntry 5 } -- ******************************************************************* -- The SONET Line Day Table. -- ******************************************************************* sonetLineDayTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetLineDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET Line Day table. Contains various statistics collected by each SONET line over multiple 1-day intervals of operation." ::= { sonetSupLine 5 } sonetLineDayEntry OBJECT-TYPE SYNTAX SonetLineDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET Line Day table." INDEX { ifIndex, sonetLineDayNumber } ::= { sonetLineDayTable 1 } SonetLineDayEntry ::= SEQUENCE { sonetLineDayNumber INTEGER, Expires January 1999 [Page 40] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetLineDayStartTime DateAndTime, sonetLineDayValidData TruthValue, sonetLineDayFCs PerfDayCount, sonetLineDayCVs PerfDayCount, sonetLineDayESs PerfDayCount, sonetLineDayESAs PerfDayCount, sonetLineDayESBs PerfDayCount, sonetLineDaySESs PerfDayCount, sonetLineDayAISSs PerfDayCount, sonetLineDayUASs PerfDayCount } sonetLineDayNumber OBJECT-TYPE SYNTAX INTEGER (1..33) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number which identifies the 1-day interval for which the set of near-end line related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval." REFERENCE "ANSI T1.231-1997 clause 9.1.2.1." ::= { sonetLineDayEntry 1 } sonetLineDayStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which this 1-day interval of near-end line measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetLineDayEntry 2 } sonetLineDayValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is Expires January 1999 [Page 41] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 missing." REFERENCE "ANSI T1.231-1997 clause 9.1.2.2." ::= { sonetLineDayEntry 3 } sonetLineDayFCs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The near-end line failure count (FC-L) is the number of occurences of near-end line failure events encountered by the SONET line layer interface in a previous 1-day interval. A near-end line failure event begins when an AIS-L failure is declared; a near-end line failure event ends when the AIS-L failure is cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.7.1." ::= { sonetLineDayEntry 4 } sonetLineDayCVs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The line code violation (CV-L) count is the number of BIP-8 errors which were detected at the SONET line layer interface in a previous 1-day interval. Each line BIP-8 can detect up to eight errors per STS-1 frame, with each error incrementing the CV counter. CVs for the line layer are collected using the BIP-8s in the B2 byte located in the line overhead of STS-1. (Since all CVs on an STS-N line are counted together, this is equivalent to counting each error in the BIP-8N contained in the B2 bytes of the STS-N line overhead.) Thus, on an STS-N signal, up to 8 x N CVs may occure in each STS-N frame." REFERENCE "ANSI T1.231-1997 clause 8.4.3.1.1.1." ::= { sonetLineDayEntry 5 } sonetLineDayESs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The line errored second (ES-L) count is the number of 1-second intervals containing one or more EDC error (B2 byte), or one or more AIS-L defects which were encountered by the SONET line layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.3.1.2." Expires January 1999 [Page 42] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 ::= { sonetLineDayEntry 6 } sonetLineDayESAs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The line errored second type A (ESA-L) count is the number of 1-second intervals containing one EDC error (B2 byte) and no AIS-L defects which were encountered by the SONET line layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.3.1.3." ::= { sonetLineDayEntry 7 } sonetLineDayESBs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The line errored second type B (ESB-L) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold EDC errors (B2 byte), and no AIS-L defects which were encountered by the SONET line layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.3.1.4." ::= { sonetLineDayEntry 8 } sonetLineDaySESs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The line severely errored second (SES-L) is a count of 1-second intervals containing sonetSevereErrorThreshold or more EDC errors (B2 byte) or one or more AIS-L defects which were encountered by the SONET line layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.3.1.5." ::= { sonetLineDayEntry 9 } sonetLineDayUASs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The line unavailable second (UAS-L) is a count of 1-second intervals for which the SONET line was unavailable during a Expires January 1999 [Page 43] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 previous 1-day interval. The SONET line becomes unavailable at the onset of 10 contiguous SES-Ls. The 10 SES-Ls are included in unavailable time. Once unavailable, the SONET line becomes available at the onset of 10 contiguous seconds with no SES-Ls. The 10 seconds with no SES-Ls are excluded from unavailable time." REFERENCE "ANSI T1.231-1997 clause 8.4.3.1.6." ::= { sonetLineDayEntry 10 } sonetLineDayAISSs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The line AIS second (AISS-L) is a count of 1-second intervals containing one or more alarm indication signal (AIS-L) defects which were encountered by the SONET line layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.3.1.7." ::= { sonetLineDayEntry 11 } -- ******************************************************************* -- Extension to the sonetFarEndLineCurrentTable found in the -- SONET-MIB. -- ******************************************************************* sonetSupFarEndLineCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSupFarEndLineCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The extension to the SONET Far End Line Current table to add more counters." ::= { sonetSupFarEndLine 1 } sonetSupFarEndLineCurrentEntry OBJECT-TYPE SYNTAX SonetSupFarEndLineCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An extension to an entry in the SONET Far End Line Current table." AUGMENTS { sonetFarEndLineCurrentEntry } ::= { sonetSupFarEndLineCurrentTable 1 } SonetSupFarEndLineCurrentEntry ::= Expires January 1999 [Page 44] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SEQUENCE { sonetFarEndLineCurrentStartTime DateAndTime, sonetFarEndLineCurrentFCs PerfCurrentCount, sonetFarEndLineCurrentESAs PerfCurrentCount, sonetFarEndLineCurrentESBs PerfCurrentCount, sonetFarEndLineCurrentAISSs PerfCurrentCount } sonetFarEndLineCurrentStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which the current 15-minute interval of far-end line measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupFarEndLineCurrentEntry 1 } sonetFarEndLineCurrentFCs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line failure count (FC-LFE) is the number of occurences of far-end line failure events detected by the SONET line layer interface in the current 15-minute interval. A far-end line failure event begins when the remote failure indication (RFI-L) failure is declared; a far-end line failure event ends when the RFI-L failure is cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.7.4." ::= { sonetSupFarEndLineCurrentEntry 2 } sonetFarEndLineCurrentESAs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line errored second type A (ESA-LFE) count is the number of 1-second intervals containing one REDC-L and no RDI-L defects which were detected by the SONET line layer interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.4.1." ::= { sonetSupFarEndLineCurrentEntry 3 } sonetFarEndLineCurrentESBs OBJECT-TYPE SYNTAX PerfCurrentCount Expires January 1999 [Page 45] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line errored second type B (ESB-LFE) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold REDC-Ls, and no RDI-L defects which were detected by the SONET line layer interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.4.1." ::= { sonetSupFarEndLineCurrentEntry 4 } sonetFarEndLineCurrentAISSs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line AIS second (AISS-LFE) is a count of 1-second intervals containing one or more RDI-L defects which were detected by the SONET line layer interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.4.1." ::= { sonetSupFarEndLineCurrentEntry 5 } -- ******************************************************************* -- Extension to the sonetFarEndLineIntervalTable found in the -- SONET-MIB. -- ******************************************************************* sonetSupFarEndLineIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSupFarEndLineIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The extension to the SONET Far End Line Interval table to add more counters." ::= { sonetSupFarEndLine 2 } sonetSupFarEndLineIntervalEntry OBJECT-TYPE SYNTAX SonetSupFarEndLineIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An extension to an entry in the SONET Far End Line Interval table." AUGMENTS { sonetFarEndLineIntervalEntry } ::= { sonetSupFarEndLineIntervalTable 1 } Expires January 1999 [Page 46] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SonetSupFarEndLineIntervalEntry ::= SEQUENCE { sonetFarEndLineIntervalStartTime DateAndTime, sonetFarEndLineIntervalFCs PerfIntervalCount, sonetFarEndLineIntervalESAs PerfIntervalCount, sonetFarEndLineIntervalESBs PerfIntervalCount, sonetFarEndLineIntervalAISSs PerfIntervalCount } sonetFarEndLineIntervalStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which this 15-minute interval of far-end line measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupFarEndLineIntervalEntry 1 } sonetFarEndLineIntervalFCs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line failure count (FC-LFE) is the number of occurences of far-end line failure events detected by the SONET line layer interface in a previous 15-minute interval. A far-end line failure event begins when the remote failure indication (RFI-L) failure is declared; a far-end line failure event ends when the RFI-L failure is cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.7.4." ::= { sonetSupFarEndLineIntervalEntry 2 } sonetFarEndLineIntervalESAs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line errored second type A (ESA-LFE) count is the number of 1-second intervals containing one REDC-L and no RDI-L defects which were detected by the SONET line layer interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.4.1." ::= { sonetSupFarEndLineIntervalEntry 3 } sonetFarEndLineIntervalESBs OBJECT-TYPE Expires January 1999 [Page 47] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line errored second type B (ESB-LFE) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold REDC-Ls, and no RDI-L defects which were detected by the SONET line layer interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.4.1." ::= { sonetSupFarEndLineIntervalEntry 4 } sonetFarEndLineIntervalAISSs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line AIS second (AISS-LFE) is a count of 1-second intervals containing one or more RDI-L defects which were detected by the SONET line layer interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.4.1." ::= { sonetSupFarEndLineIntervalEntry 5 } -- ******************************************************************* -- The SONET Far End Line Day Table. -- ******************************************************************* sonetFarEndLineDayTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetFarEndLineDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET Far End Line Day table. Contains various statistics collected by each SONET line over multiple 1-day intervals of operation." ::= { sonetSupFarEndLine 3 } sonetFarEndLineDayEntry OBJECT-TYPE SYNTAX SonetFarEndLineDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET Far End Line Day table." INDEX { ifIndex, sonetFarEndLineDayNumber } ::= { sonetFarEndLineDayTable 1 } Expires January 1999 [Page 48] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SonetFarEndLineDayEntry ::= SEQUENCE { sonetFarEndLineDayNumber INTEGER, sonetFarEndLineDayStartTime DateAndTime, sonetFarEndLineDayValidData TruthValue, sonetFarEndLineDayFCs PerfDayCount, sonetFarEndLineDayCVs PerfDayCount, sonetFarEndLineDayESs PerfDayCount, sonetFarEndLineDayESAs PerfDayCount, sonetFarEndLineDayESBs PerfDayCount, sonetFarEndLineDaySESs PerfDayCount, sonetFarEndLineDayUASs PerfDayCount, sonetFarEndLineDayAISSs PerfDayCount } sonetFarEndLineDayNumber OBJECT-TYPE SYNTAX INTEGER (1..33) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number which identifies the 1-day interval for which the set of far-end line related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval." REFERENCE "ANSI T1.231-1997 clause 9.1.2.1." ::= { sonetFarEndLineDayEntry 1 } sonetFarEndLineDayStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which this 1-day interval of far-end line measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetFarEndLineDayEntry 2 } sonetFarEndLineDayValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) Expires January 1999 [Page 49] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is missing (e.g., when a near-end defect prevents some far-end data from being collected)." REFERENCE "ANSI T1.231-1997 clause 9.1.2.2." ::= { sonetFarEndLineDayEntry 3 } sonetFarEndLineDayFCs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line failure count (FC-LFE) is the number of occurences of far-end line failure events detected by the SONET line layer interface in a previous 1-day interval. A far-end line failure event begins when the remote failure indication (RFI-L) failure is declared; a far-end line failure event ends when the RFI-L failure is cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.7.4." ::= { sonetFarEndLineDayEntry 4 } sonetFarEndLineDayCVs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line code violation (CV-LFE) count is the number of REI-Ls which were detected at the SONET line layer interface in a previous 1-day interval. For EC-1 or OC-1, REI-L is bits 5 to 8 of the M0 byte; for EC-N or OC-N (N>2), M1 byte." REFERENCE "ANSI T1.231-1997 clause 8.4.4.1." ::= { sonetFarEndLineDayEntry 5 } sonetFarEndLineDayESs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line errored second (ES-LFE) count is the number of 1-second intervals containing one or more REDC-Ls, or one or more RDI-L defects which were encountered by the SONET line layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.4.1." ::= { sonetFarEndLineDayEntry 6 } sonetFarEndLineDayESAs OBJECT-TYPE Expires January 1999 [Page 50] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line errored second type A (ESA-LFE) count is the number of 1-second intervals containing one REDC-L and no RDI-L defects which were detected by the SONET line layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.4.1." ::= { sonetFarEndLineDayEntry 7 } sonetFarEndLineDayESBs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line errored second type B (ESB-LFE) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold REDC-Ls, and no RDI-L defects which were detected by the SONET line layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.4.1." ::= { sonetFarEndLineDayEntry 8 } sonetFarEndLineDaySESs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line severely errored second (SES-LFE) is a count of 1-second intervals containing sonetSevereErrorThreshold or more REDC-Ls or one or more RDI-L defects which were detected by the SONET line layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.4.1." ::= { sonetFarEndLineDayEntry 9 } sonetFarEndLineDayUASs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line unavailable second (UAS-LFE) is a count of 1-second intervals for which the SONET line was unavailable during a previous 1-day interval. The SONET line becomes unavailable at the onset of 10 contiguous SES-LEFs. The 10 SES-LEFs are included in unavailable time. Once unavailable, the SONET line becomes available at the onset of 10 contiguous Expires January 1999 [Page 51] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 seconds with no SES-LEFs. The 10 seconds with no SES-LEFs are excluded from unavailable time." REFERENCE "ANSI T1.231-1997 clause 8.4.4.1." ::= { sonetFarEndLineDayEntry 10 } sonetFarEndLineDayAISSs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end line AIS second (AISS-LFE) is a count of 1-second intervals containing one or more RDI-L defects which were detected by the SONET line layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.4.1." ::= { sonetFarEndLineDayEntry 11 } -- ********************************************************************* -- SONET STS-Path group object definitions. -- -- SONET STS-Path default threshold value object definitions. These -- default values apply to both near-end and far-end Path interfaces. -- ********************************************************************* sonetPathDefaultThresholdTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetPathDefaultThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of default thresholds for SONET Path counters." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSupPath 1 } sonetPathDefaultThresholdEntry OBJECT-TYPE SYNTAX SonetPathDefaultThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table of default thresholds. The table has a variable for each counter type and accumulation period combination, but uses indexes to indetify the digital signal direction and rate. The agent must provide a set of default threshold values for all rates that the NE supports. The agent may make these variables read-only." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." INDEX { sonetPathDefaultThresholdDirection, Expires January 1999 [Page 52] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetPathDefaultThresholdRate } ::= { sonetPathDefaultThresholdTable 1 } SonetPathDefaultThresholdEntry ::= SEQUENCE { sonetPathDefaultThresholdDirection INTEGER, sonetPathDefaultThresholdRate INTEGER, sonetPathDefaultCVThreshold INTEGER, sonetPathDefaultESThreshold INTEGER, sonetPathDefaultESAThreshold INTEGER, sonetPathDefaultESBThreshold INTEGER, sonetPathDefaultSESThreshold INTEGER, sonetPathDefaultUASThreshold INTEGER, sonetPathDefaultPPJCGenThreshold INTEGER, sonetPathDefaultNPJCGenThreshold INTEGER, sonetPathDefaultPPJCDetThreshold INTEGER, sonetPathDefaultNPJCDetThreshold INTEGER, sonetPathDefaultPJCSGenThreshold INTEGER, sonetPathDefaultPJCSDetThreshold INTEGER, sonetPathDefaultPJCDiffThreshold INTEGER, sonetPathDefaultDayCVThreshold INTEGER, sonetPathDefaultDayESThreshold INTEGER, sonetPathDefaultDayESAThreshold INTEGER, sonetPathDefaultDayESBThreshold INTEGER, sonetPathDefaultDaySESThreshold INTEGER, sonetPathDefaultDayUASThreshold INTEGER, sonetPathDefaultDayPPJCGenThreshold INTEGER, sonetPathDefaultDayNPJCGenThreshold INTEGER, sonetPathDefaultDayPPJCDetThreshold INTEGER, sonetPathDefaultDayNPJCDetThreshold INTEGER, sonetPathDefaultDayPJCSGenThreshold INTEGER, sonetPathDefaultDayPJCSDetThreshold INTEGER, sonetPathDefaultDayPJCDiffThreshold INTEGER } sonetPathDefaultThresholdDirection OBJECT-TYPE SYNTAX INTEGER { nearEnd(1), farEnd(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The digital signal direction for which the default threshold values apply." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 1 } Expires January 1999 [Page 53] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetPathDefaultThresholdRate OBJECT-TYPE SYNTAX INTEGER { sts1(1), sts3(2), sts12(3), sts24(4), sts48(5), sts192(6) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The path digital signal rate for which the default threshold values apply." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 2 } sonetPathDefaultCVThreshold OBJECT-TYPE SYNTAX INTEGER (1..16383) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET CV-P and CV-PFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 3 } sonetPathDefaultESThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ES-P and ES-PFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 4 } sonetPathDefaultESAThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESA-P and ESA-PFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 5 } Expires January 1999 [Page 54] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetPathDefaultESBThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESB-P and ESB-PFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 6 } sonetPathDefaultSESThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET SES-P and SES-PFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 7 } sonetPathDefaultUASThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET UAS-P and UAS-PFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 8 } sonetPathDefaultPPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PPJC-PGen counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 9 } sonetPathDefaultNPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET NPJC-PGen counter 15-minute interval thresholds." Expires January 1999 [Page 55] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 10 } sonetPathDefaultPPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PPJC-PDet counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 11 } sonetPathDefaultNPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET NPJC-PDet counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 12 } sonetPathDefaultPJCSGenThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PJCS-PGen counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 13 } sonetPathDefaultPJCSDetThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PJCS-PDet counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 14 } sonetPathDefaultPJCDiffThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current Expires January 1999 [Page 56] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 DESCRIPTION "The default value for SONET PJCDiff-P counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 15 } sonetPathDefaultDayCVThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET CV-P and CV-PFE counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 16 } sonetPathDefaultDayESThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ES-P and ES-PFE counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 17 } sonetPathDefaultDayESAThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESA-P and ESA-PFE counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 18 } sonetPathDefaultDayESBThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESB-P and ESB-PFE counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 19 } sonetPathDefaultDaySESThreshold OBJECT-TYPE Expires January 1999 [Page 57] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SYNTAX INTEGER (1..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET SES-P and SES-PFE counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 20 } sonetPathDefaultDayUASThreshold OBJECT-TYPE SYNTAX INTEGER (1..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET UAS-P and UAS-PFE counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 21 } sonetPathDefaultDayPPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (1..16777215) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PPJC-PGen counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 22 } sonetPathDefaultDayNPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (1..16777215) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET NPJC-PGen counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 23 } sonetPathDefaultDayPPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (1..16777215) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PPJC-PDet counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." Expires January 1999 [Page 58] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 ::= { sonetPathDefaultThresholdEntry 24 } sonetPathDefaultDayNPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (1..16777215) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET NPJC-PDet counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 25 } sonetPathDefaultDayPJCSGenThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PJCS-PGen counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 26 } sonetPathDefaultDayPJCSDetThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PJCS-PDet counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 27 } sonetPathDefaultDayPJCDiffThreshold OBJECT-TYPE SYNTAX INTEGER (1..16777215) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PJCDiff-P counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetPathDefaultThresholdEntry 28 } -- ********************************************************************* -- SONET Path threshold value object definitions. This table is an -- extension to the sonetPathCurrentTable found in the SONET-MIB. -- ********************************************************************* Expires January 1999 [Page 59] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetPathThresholdTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetPathThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of trap threshold values for SONET Path counters." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSupPath 2 } sonetPathThresholdEntry OBJECT-TYPE SYNTAX SonetPathThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table of SONET Path trap thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." AUGMENTS { sonetPathCurrentEntry } ::= { sonetPathThresholdTable 1 } SonetPathThresholdEntry ::= SEQUENCE { sonetPathCurrentCVThreshold INTEGER, sonetPathCurrentESThreshold INTEGER, sonetPathCurrentESAThreshold INTEGER, sonetPathCurrentESBThreshold INTEGER, sonetPathCurrentSESThreshold INTEGER, sonetPathCurrentUASThreshold INTEGER, sonetPathCurrentPPJCGenThreshold INTEGER, sonetPathCurrentNPJCGenThreshold INTEGER, sonetPathCurrentPPJCDetThreshold INTEGER, sonetPathCurrentNPJCDetThreshold INTEGER, sonetPathCurrentPJCSGenThreshold INTEGER, sonetPathCurrentPJCSDetThreshold INTEGER, sonetPathCurrentPJCDiffThreshold INTEGER, sonetPathDayCVThreshold INTEGER, sonetPathDayESThreshold INTEGER, sonetPathDayESAThreshold INTEGER, sonetPathDayESBThreshold INTEGER, sonetPathDaySESThreshold INTEGER, sonetPathDayUASThreshold INTEGER, sonetPathDayPPJCGenThreshold INTEGER, sonetPathDayNPJCGenThreshold INTEGER, sonetPathDayPPJCDetThreshold INTEGER, sonetPathDayNPJCDetThreshold INTEGER, sonetPathDayPJCSGenThreshold INTEGER, sonetPathDayPJCSDetThreshold INTEGER, sonetPathDayPJCDiffThreshold INTEGER Expires January 1999 [Page 60] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 } sonetPathCurrentCVThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval CV-P and CV-PFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 1 } sonetPathCurrentESThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval ES-P and ES-PFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 2 } sonetPathCurrentESAThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval ESA-P and ESA-PFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 3 } sonetPathCurrentESBThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval ESB-P and ESB-PFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." Expires January 1999 [Page 61] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 DEFVAL { 0 } ::= { sonetPathThresholdEntry 4 } sonetPathCurrentSESThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval SES-P and SES-PFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 5 } sonetPathCurrentUASThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval UAS-P and UAS-PFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 6 } sonetPathCurrentPPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval PPJC-PGen counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 7 } sonetPathCurrentNPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval NPJC-PGen counter. A value of zero indicates that the default threshold value is to be used." Expires January 1999 [Page 62] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 8 } sonetPathCurrentPPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval PPJC-PDet counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 9 } sonetPathCurrentNPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval NPJC-PDet counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 10 } sonetPathCurrentPJCSGenThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval PJCS-PGen counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 11 } sonetPathCurrentPJCSDetThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval PJCS-PDet counter. A value of zero indicates that the Expires January 1999 [Page 63] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 12 } sonetPathCurrentPJCDiffThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval PJCDiff-P counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 13 } sonetPathDayCVThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day CV-P and CV-PFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 14 } sonetPathDayESThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day ES-P and ES-PFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 15 } sonetPathDayESAThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day Expires January 1999 [Page 64] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 ESA-P and ESA-PFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 16 } sonetPathDayESBThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day ESB-P and ESB-PFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 17 } sonetPathDaySESThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day SES-P and SES-PFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 18 } sonetPathDayUASThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day UAS-P and UAS-PFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 19 } sonetPathDayPPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION Expires January 1999 [Page 65] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 "The trap threshold value for the interface's current 1-day interval PPJC-PGen counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 20 } sonetPathDayNPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day interval NPJC-PGen counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 21 } sonetPathDayPPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day interval PPJC-PDet counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 22 } sonetPathDayNPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day interval NPJC-PDet counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 23 } sonetPathDayPJCSGenThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current Expires January 1999 [Page 66] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 DESCRIPTION "The trap threshold value for the interface's current 1-day interval PJCS-PGen counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 24 } sonetPathDayPJCSDetThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day interval PJCS-PDet counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 25 } sonetPathDayPJCDiffThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day interval PJCDiff-P counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetPathThresholdEntry 26 } -- ********************************************************************* -- Extension to the sonetPathCurrentTable found in the SONET-MIB. -- ********************************************************************* sonetSupPathCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSupPathCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Extension to the SONET Path Current table." ::= { sonetSupPath 3 } sonetSupPathCurrentEntry OBJECT-TYPE SYNTAX SonetSupPathCurrentEntry MAX-ACCESS not-accessible Expires January 1999 [Page 67] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 STATUS current DESCRIPTION "Various extensions to an entry in the SONET Path Current table." AUGMENTS { sonetPathCurrentEntry } ::= { sonetSupPathCurrentTable 1 } SonetSupPathCurrentEntry ::= SEQUENCE { sonetPathSevereErrorThreshold Integer32, sonetPathResetCounters INTEGER, sonetPathCurrentStartTime DateAndTime, sonetPathCurrentFCs PerfCurrentCount, sonetPathCurrentESAs PerfCurrentCount, sonetPathCurrentESBs PerfCurrentCount, sonetPathCurrentPPJCGens PerfCurrentCount, sonetPathCurrentNPJCGens PerfCurrentCount, sonetPathCurrentPPJCDets PerfCurrentCount, sonetPathCurrentNPJCDets PerfCurrentCount, sonetPathCurrentPJCSGens PerfCurrentCount, sonetPathCurrentPJCSDets PerfCurrentCount, sonetPathCurrentPJCDiffs PerfCurrentCount } sonetPathSevereErrorThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of STS-path EDC errors (B3 byte) in a 1-second interval at which point the condition is counted as a severe error. The value of this variable should correspond to the value indicated by sonetSESthresholdSet in the SONET-MIB. If sonetSESthresholdSet is set to other(1), this variable is the soul source of this information. This value applies to all near-end and far-end path SES counters." REFERENCE "ANSI T1.231-1997 clause 8.4.5.5." ::= { sonetSupPathCurrentEntry 1 } sonetPathResetCounters OBJECT-TYPE SYNTAX INTEGER { nearEndCurrent15Minute(1), nearEndCurrent1day(2), farEndCurrent15Minute(3), farEndCurrent1day(4), all(5) } Expires January 1999 [Page 68] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 MAX-ACCESS read-write STATUS current DESCRIPTION "This varible provides the capability to initialize SONET near-end and far-end STS-path layer performance counters to zero (0) on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupPathCurrentEntry 2 } sonetPathCurrentStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which the current 15-minute interval of near-end STS-path measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupPathCurrentEntry 3 } sonetPathCurrentFCs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The near-end path failure count (FC-P) is the number of occurences of near-end path failure events encountered by the SONET path layer interface in the current 15-minute interval. A near-end path failure event begins when the first of any of LOP-P, AIS-P, TIM-P or UNEQ-P failures is declared; a near-end path failure event ends when all LOP-P, AIS-P, TIM-P and UNEQ-P failures have cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.8.1." ::= { sonetSupPathCurrentEntry 4 } sonetPathCurrentESAs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path errored second type A (ESA-P) count is the number of 1-second intervals containing one EDC error (B3 byte) and no AIS-P, LOP-P, TIM-P or UNEQ-P defects which were encountered by the SONET path layer interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.3." ::= { sonetSupPathCurrentEntry 5 } Expires January 1999 [Page 69] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetPathCurrentESBs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path errored second type B (ESB-P) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold EDC errors (B3 byte), and no AIS-P, LOP-P, TIM-P or UNEQ-P defects which were encountered by the SONET path layer interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.4." ::= { sonetSupPathCurrentEntry 6 } sonetPathCurrentPPJCGens OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PPJC-PGen is a count of STS-path positive pointer justifications generated by the NE in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.1." ::= { sonetSupPathCurrentEntry 7 } sonetPathCurrentNPJCGens OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The NPJC-PGen is a count of STS-path negative pointer justifications generated by the NE in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.2." ::= { sonetSupPathCurrentEntry 8 } sonetPathCurrentPPJCDets OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PPJC-PDet is a count of STS-path positive pointer justifications detected by the NE in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.3." ::= { sonetSupPathCurrentEntry 9 } sonetPathCurrentNPJCDets OBJECT-TYPE Expires January 1999 [Page 70] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The NPJC-PGen is a count of STS-path negative pointer justifications detected by the NE in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.4." ::= { sonetSupPathCurrentEntry 10 } sonetPathCurrentPJCSGens OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCS-PGen is a count of 1-second intervals containing one or more STS-path pointer justification movements generated by the NE in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.8." ::= { sonetSupPathCurrentEntry 11 } sonetPathCurrentPJCSDets OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCS-PDet is a count of 1-second intervals containing one or more STS-path pointer justification movements detected by the NE in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.9." ::= { sonetSupPathCurrentEntry 12 } sonetPathCurrentPJCDiffs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCDiff-P is the absolute value of the difference between the net number of detected pointer movement counts and the net number of generated pointer movement counts in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.10." ::= { sonetSupPathCurrentEntry 13 } -- ******************************************************************* -- Extension to the sonetPathIntervalTable found in the SONET-MIB. Expires January 1999 [Page 71] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 -- ******************************************************************* sonetSupPathIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSupPathIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The extension to the SONET Path Interval table to add more counters." ::= { sonetSupPath 4 } sonetSupPathIntervalEntry OBJECT-TYPE SYNTAX SonetSupPathIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An extension to an entry in the SONET Path Interval table." AUGMENTS { sonetPathIntervalEntry } ::= { sonetSupPathIntervalTable 1 } SonetSupPathIntervalEntry ::= SEQUENCE { sonetPathIntervalStartTime DateAndTime, sonetPathIntervalFCs PerfIntervalCount, sonetPathIntervalESAs PerfIntervalCount, sonetPathIntervalESBs PerfIntervalCount, sonetPathIntervalPPJCGens PerfIntervalCount, sonetPathIntervalNPJCGens PerfIntervalCount, sonetPathIntervalPPJCDets PerfIntervalCount, sonetPathIntervalNPJCDets PerfIntervalCount, sonetPathIntervalPJCSGens PerfIntervalCount, sonetPathIntervalPJCSDets PerfIntervalCount, sonetPathIntervalPJCDiffs PerfIntervalCount } sonetPathIntervalStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which this 15-minute interval of measurements began on this STS-path." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupPathIntervalEntry 1 } sonetPathIntervalFCs OBJECT-TYPE Expires January 1999 [Page 72] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The near-end path failure count (FC-P) is the number of occurences of near-end path failure events encountered by the SONET path layer interface in a previous 15-minute interval. A near-end path failure event begins when the first of any of LOP-P, AIS-P, TIM-P or UNEQ-P failures is declared; a near-end path failure event ends when all LOP-P, AIS-P, TIM-P and UNEQ-P failures have cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.8.1." ::= { sonetSupPathIntervalEntry 2 } sonetPathIntervalESAs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path errored second type A (ESA-P) count is the number of 1-second intervals containing one EDC error (B3 byte) and no AIS-P, LOP-P, TIM-P or UNEQ-P defects which were encountered by the SONET path layer interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.3." ::= { sonetSupPathIntervalEntry 3 } sonetPathIntervalESBs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path errored second type B (ESB-P) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold EDC errors (B3 byte) and no AIS-P, LOP-P, TIM-P or UNEQ-P defects which were encountered by the SONET path layer interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.4." ::= { sonetSupPathIntervalEntry 4 } sonetPathIntervalPPJCGens OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PPJC-PGen is a count of STS-path positive pointer justifications generated by the NE in the previous or recent Expires January 1999 [Page 73] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.1." ::= { sonetSupPathIntervalEntry 5 } sonetPathIntervalNPJCGens OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The NPJC-PGen is a count of STS-path negative pointer justifications generated by the NE in the previous or recent 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.2." ::= { sonetSupPathIntervalEntry 6 } sonetPathIntervalPPJCDets OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PPJC-PDet is a count of STS-path positive pointer justifications detected by the NE in the previous or recent 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.3." ::= { sonetSupPathIntervalEntry 7 } sonetPathIntervalNPJCDets OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The NPJC-PGen is a count of STS-path negative pointer justifications detected by the NE in the previous or recent 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.4." ::= { sonetSupPathIntervalEntry 8 } sonetPathIntervalPJCSGens OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCS-PGen is a count of 1-second intervals containing one or more STS-path pointer justification movements generated by the NE in the previous or recent 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.8." ::= { sonetSupPathIntervalEntry 9 } Expires January 1999 [Page 74] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetPathIntervalPJCSDets OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCS-PDet is a count of 1-second intervals containing one or more STS-path pointer justification movements detected by the NE in the previous or recent 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.9." ::= { sonetSupPathIntervalEntry 10 } sonetPathIntervalPJCDiffs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCDiff-P is the absolute value of the difference between the net number of detected pointer movement counts and the net number of generated pointer movement counts in the previous or recent 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.10." ::= { sonetSupPathIntervalEntry 11 } -- ******************************************************************* -- The SONET Path Day Table. -- ******************************************************************* sonetPathDayTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetPathDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET Path Day table. Contains performance statistics collected by each SONET Path over multiple 1-day intervals of operation." ::= { sonetSupPath 17 } sonetPathDayEntry OBJECT-TYPE SYNTAX SonetPathDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET Path Day table." INDEX { ifIndex, sonetPathDayNumber } ::= { sonetPathDayTable 1 } Expires January 1999 [Page 75] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SonetPathDayEntry ::= SEQUENCE { sonetPathDayNumber INTEGER, sonetPathDayStartTime DateAndTime, sonetPathDayValidData TruthValue, sonetPathDayFCs PerfDayCount, sonetPathDayCVs PerfDayCount, sonetPathDayESs PerfDayCount, sonetPathDayESAs PerfDayCount, sonetPathDayESBs PerfDayCount, sonetPathDaySESs PerfDayCount, sonetPathDayUASs PerfDayCount, sonetPathDayPPJCGens PerfDayCount, sonetPathDayNPJCGens PerfDayCount, sonetPathDayPPJCDets PerfDayCount, sonetPathDayNPJCDets PerfDayCount, sonetPathDayPJCSGens PerfDayCount, sonetPathDayPJCSDets PerfDayCount, sonetPathDayPJCDiffs PerfDayCount } sonetPathDayNumber OBJECT-TYPE SYNTAX INTEGER (1..33) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number which identifies the 1-day interval for which the set of near-end path related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval." REFERENCE "ANSI T1.231-1997 clause 9.1.2.1." ::= { sonetPathDayEntry 1 } sonetPathDayStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which the 1-day interval of measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.2.1." ::= { sonetPathDayEntry 2 } sonetPathDayValidData OBJECT-TYPE Expires January 1999 [Page 76] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is missing." REFERENCE "ANSI T1.231-1997 clause 9.1.2.2." ::= { sonetPathDayEntry 3 } sonetPathDayFCs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The near-end path failure count (FC-P) is the number of occurences of near-end path failure events encountered by the SONET path layer interface in a previous 1-day interval. A near-end path failure event begins when the first of any of LOP-P, AIS-P, TIM-P or UNEQ-P failures is declared; a near-end path failure event ends when all LOP-P, AIS-P, TIM-P and UNEQ-P failures have cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.8.1." ::= { sonetPathDayEntry 4 } sonetPathDayCVs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path code violation (CV-P) count is the number of BIP-8 errors which were detected at the STS-path layer interface in a previous 1-day interval. CVs for the path layer are collected using the BIP-8 in the B3 byte located in the STS-path overhead." REFERENCE "ANSI T1.231-1997 clause 8.4.5.1.1." ::= { sonetPathDayEntry 5 } sonetPathDayESs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path errored second (ES-P) count is the number of 1-second Expires January 1999 [Page 77] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 intervals containing one or more EDC error (B3 byte), or one or more AIS-P, LOP-P, TIM-P or UNEQ-P defects which were encountered by the SONET path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.2." ::= { sonetPathDayEntry 6 } sonetPathDayESAs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path errored second type A (ESA-P) count is the number of 1-second intervals containing one EDC error (B3 byte) and no AIS-P, LOP-P, TIM-P or UNEQ-P defects which were encountered by the SONET path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.3." ::= { sonetPathDayEntry 7 } sonetPathDayESBs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path errored second type B (ESB-P) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold EDC errors (B3 byte) and no AIS-P, LOP-P, TIM-P or UNEQ-P defects which were encountered by the SONET path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.4." ::= { sonetPathDayEntry 8 } sonetPathDaySESs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path severely errored second (SES-P) is a count of 1-second intervals containing sonetSevereErrorThreshold or more EDC error (B3 byte), or one or more AIS-P, LOP-P, TIM-P or UNEQ-P defects which were encountered by the SONET path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.5." ::= { sonetPathDayEntry 9 } sonetPathDayUASs OBJECT-TYPE SYNTAX PerfDayCount Expires January 1999 [Page 78] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 MAX-ACCESS read-only STATUS current DESCRIPTION "The path unavailable second (UAS-P) is a count of 1-second intervals for which the SONET STS-path was unavailable during a previous 1-day interval. The SONET STS-path becomes unavailable at the onset of 10 contiguous SES-Ps. The 10 SES-Ps are included in unavailable time. Once unavailable, the SONET STS-path becomes available at the onset of 10 contiguous seconds with no SES-Ps. The 10 seconds with no SES-Ps are excluded from unavailable time." REFERENCE "ANSI T1.231-1997 clause 8.4.5.6." ::= { sonetPathDayEntry 10 } sonetPathDayPPJCGens OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PPJC-PGen is a count of STS-path positive pointer justifications generated by the NE in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.1." ::= { sonetPathDayEntry 11 } sonetPathDayNPJCGens OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The NPJC-PGen is a count of STS-path negative pointer justifications generated by the NE in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.2." ::= { sonetPathDayEntry 12 } sonetPathDayPPJCDets OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PPJC-PDet is a count of STS-path positive pointer justifications detected by the NE in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.3." ::= { sonetPathDayEntry 13 } sonetPathDayNPJCDets OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only Expires January 1999 [Page 79] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 STATUS current DESCRIPTION "The NPJC-PGen is a count of STS-path negative pointer justifications detected by the NE in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.4." ::= { sonetPathDayEntry 14 } sonetPathDayPJCSGens OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCS-PGen is a count of 1-second intervals containing one or more STS-path pointer justification movements generated by the NE in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.8." ::= { sonetPathDayEntry 15 } sonetPathDayPJCSDets OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCS-PDet is a count of 1-second intervals containing one or more STS-path pointer justification movements detected by the NE in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.9." ::= { sonetPathDayEntry 16 } sonetPathDayPJCDiffs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCDiff-P is the absolute value of the difference between the net number of detected pointer movement counts and the net number of generated pointer movement counts in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.10." ::= { sonetPathDayEntry 17 } -- ******************************************************************* -- Extension to the sonetFarEndPathCurrentTable found in the -- SONET-MIB. -- ******************************************************************* Expires January 1999 [Page 80] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetSupFarEndPathCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSupFarEndPathCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The extension to the SONET Far End Path Current table to add more counters." ::= { sonetSupFarEndPath 1 } sonetSupFarEndPathCurrentEntry OBJECT-TYPE SYNTAX SonetSupFarEndPathCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An extension to an entry in the SONET Far End Path Current table." AUGMENTS { sonetFarEndPathCurrentEntry } ::= { sonetSupFarEndPathCurrentTable 1 } SonetSupFarEndPathCurrentEntry ::= SEQUENCE { sonetFarEndPathCurrentStartTime DateAndTime, sonetFarEndPathCurrentFCs PerfCurrentCount, sonetFarEndPathCurrentESAs PerfCurrentCount, sonetFarEndPathCurrentESBs PerfCurrentCount } sonetFarEndPathCurrentStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which the current 15-minute interval of measurements began on this Far End Path." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupFarEndPathCurrentEntry 1 } sonetFarEndPathCurrentFCs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path failure count (FC-PFE) is the number of occurences of far-end path failure events detected by the SONET STS-path layer interface in the current 15-minute interval. A far-end path failure event begins when the first of any remote failure indication (RFI-P, RFI-P server, or RFI-P connectivity) Expires January 1999 [Page 81] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 failure is declared; a far-end path failure event ends when all RFI-P, RFI-P server, or RFI-P connectivity failures are cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.8.2." ::= { sonetSupFarEndPathCurrentEntry 2 } sonetFarEndPathCurrentESAs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path errored second type A (ESA-PFE) count is the number of 1-second intervals containing one REDC-P and no RDI-P, ERDI-P server or ERDI-P connectivity defects which were detected by the SONET STS-path layer interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetSupFarEndPathCurrentEntry 3 } sonetFarEndPathCurrentESBs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path errored second type B (ESB-PFE) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold REDC-Ps and no RDI-P, ERDI-P server or ERDI-P connectivity defects which were detected by the SONET STS-path layer interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetSupFarEndPathCurrentEntry 4 } -- ******************************************************************* -- Extension to the sonetFarEndPathIntervalTable found in the -- SONET-MIB. -- ******************************************************************* sonetSupFarEndPathIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSupFarEndPathIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The extension to the SONET Far End Path Interval table to add more counters." ::= { sonetSupFarEndPath 2 } Expires January 1999 [Page 82] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetSupFarEndPathIntervalEntry OBJECT-TYPE SYNTAX SonetSupFarEndPathIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An extension to an entry in the SONET Far End Path Interval table." AUGMENTS { sonetFarEndPathIntervalEntry } ::= { sonetSupFarEndPathIntervalTable 1 } SonetSupFarEndPathIntervalEntry ::= SEQUENCE { sonetFarEndPathIntervalStartTime DateAndTime, sonetFarEndPathIntervalFCs PerfIntervalCount, sonetFarEndPathIntervalESAs PerfIntervalCount, sonetFarEndPathIntervalESBs PerfIntervalCount } sonetFarEndPathIntervalStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which this 15-minute interval of far-end path measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupFarEndPathIntervalEntry 1 } sonetFarEndPathIntervalFCs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path failure count (FC-PFE) is the number of occurences of far-end path failure events detected by the SONET STS-path layer interface in a previous 15-minute interval. A far-end path failure event begins when the first of any remote failure indication (RFI-P, RFI-P server, or RFI-P connectivity) failure is declared; a far-end path failure event ends when all RFI-P, RFI-P server, or RFI-P connectivity failures are cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.8.2." ::= { sonetSupFarEndPathIntervalEntry 2 } sonetFarEndPathIntervalESAs OBJECT-TYPE SYNTAX PerfIntervalCount Expires January 1999 [Page 83] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path errored second type A (ESA-PFE) count is the number of 1-second intervals containing one REDC-P and no RDI-P, ERDI-P server or ERDI-P connectivity defects which were detected by the SONET STS-path layer interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetSupFarEndPathIntervalEntry 3 } sonetFarEndPathIntervalESBs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path errored second type B (ESB-PFE) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold REDC-Ps, and no RDI-P, ERDI-P server or ERDI-P connectivity defects which were detected by the SONET STS-path layer interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetSupFarEndPathIntervalEntry 4 } -- ******************************************************************* -- The SONET Far End Path Day Table. -- ******************************************************************* sonetFarEndPathDayTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetFarEndPathDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET Far End Path Day table. Contains various statistics collected by each SONET Far End Path over multiple 1-day intervals of operation." ::= { sonetSupFarEndPath 3 } sonetFarEndPathDayEntry OBJECT-TYPE SYNTAX SonetFarEndPathDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET Far End Path Day table." INDEX { ifIndex, sonetFarEndPathDayNumber } ::= { sonetFarEndPathDayTable 1 } Expires January 1999 [Page 84] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SonetFarEndPathDayEntry ::= SEQUENCE { sonetFarEndPathDayNumber INTEGER, sonetFarEndPathDayStartTime DateAndTime, sonetFarEndPathDayValidData TruthValue, sonetFarEndPathDayFCs PerfDayCount, sonetFarEndPathDayCVs PerfDayCount, sonetFarEndPathDayESs PerfDayCount, sonetFarEndPathDayESAs PerfDayCount, sonetFarEndPathDayESBs PerfDayCount, sonetFarEndPathDaySESs PerfDayCount, sonetFarEndPathDayUASs PerfDayCount } sonetFarEndPathDayNumber OBJECT-TYPE SYNTAX INTEGER (1..4) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number which identifies the 1-day interval for which the set of far-end path related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval." REFERENCE "ANSI T1.231-1997 clause 9.1.2.1." ::= { sonetFarEndPathDayEntry 1 } sonetFarEndPathDayStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which the current interval of measurements began." REFERENCE "ANSI T1.231-1997 clause 9.1.2.1." ::= { sonetFarEndPathDayEntry 2 } sonetFarEndPathDayValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise Expires January 1999 [Page 85] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is missing (e.g., when a near-end defect prevents some far-end data from being collected)." REFERENCE "ANSI T1.231-1997 clause 9.1.2.2." ::= { sonetFarEndPathDayEntry 3 } sonetFarEndPathDayFCs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path failure count (FC-PFE) is the number of occurences of far-end path failure events detected by the SONET STS-path layer interface in a previous 1-day interval. A far-end path failure event begins when the first of any remote failure indication (RFI-P, RFI-P server, or RFI-P connectivity) failure is declared; a far-end path failure event ends when all RFI-P, RFI-P server, or RFI-P connectivity failures are cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.8.2." ::= { sonetFarEndPathDayEntry 4 } sonetFarEndPathDayCVs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path code violation (CV-PFE) count is the number of REI-Ps (bit 1-4 in G1 byte) which were detected at the SONET STS-path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetFarEndPathDayEntry 5 } sonetFarEndPathDayESs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path errored second (ES-PFE) count is the number of 1-second intervals containing one or more REDC-P, or one or more RDI-P, ERDI-P server or ERDI-P connectivity defects which were encountered by the SONET STS-path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetFarEndPathDayEntry 6 } Expires January 1999 [Page 86] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetFarEndPathDayESAs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path errored second type A (ESA-PFE) count is the number of 1-second intervals containing one REDC-P and no RDI-P, ERDI-P server or ERDI-P connectivity defects which were detected by the SONET STS-path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetFarEndPathDayEntry 7 } sonetFarEndPathDayESBs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path errored second type B (ESB-PFE) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold REDC-Ps and no RDI-P, ERDI-P server or ERDI-P connectivity defects which were detected by the SONET STS-path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetFarEndPathDayEntry 8 } sonetFarEndPathDaySESs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path severely errored second (SES-PFE) is a count of 1-second intervals containing sonetSevereErrorThreshold or more REDC-Ps or one or more RDI-P, ERDI-P server or ERDI-P connectivity defects which were detected by the SONET STS-path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5." ::= { sonetFarEndPathDayEntry 9 } sonetFarEndPathDayUASs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path unavailable second (UAS-PFE) is a count of 1-second intervals for which the SONET STS-path was unavailable during a previous 1-day interval. The SONET STS-path becomes Expires January 1999 [Page 87] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 unavailable at the onset of 10 contiguous SES-PFEs. The 10 SES-PFEs are included in unavailable time. Once unavailable, the SONET STS-path becomes available at the onset of 10 contiguous seconds with no SES-PFEs. The 10 seconds with no SES-PFEs are excluded from unavailable time." REFERENCE "ANSI T1.231-1997 clause 8.4.5.1." ::= { sonetFarEndPathDayEntry 10 } -- ********************************************************************* -- SONET VT-Path group object definitions. -- -- SONET VT-Path default threshold value object definitions. These -- default values apply to both near-end and far-end Path interfaces. -- ********************************************************************* sonetVTDefaultThresholdTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetVTDefaultThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of default thresholds for SONET Path counters." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSupVT 1 } sonetVTDefaultThresholdEntry OBJECT-TYPE SYNTAX SonetVTDefaultThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table of default thresholds. The table has a variable for each counter type and accumulation period combination, but uses indexes to indetify the digital signal direction and rate. The agent must provide a set of default threshold values for all rates that the NE supports. The agent may make these variables read-only." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." INDEX { sonetVTDefaultThresholdDirection, sonetVTDefaultThresholdRate } ::= { sonetVTDefaultThresholdTable 1 } SonetVTDefaultThresholdEntry ::= SEQUENCE { sonetVTDefaultThresholdDirection INTEGER, sonetVTDefaultThresholdRate INTEGER, sonetVTDefaultCVThreshold INTEGER, sonetVTDefaultESThreshold INTEGER, Expires January 1999 [Page 88] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetVTDefaultESAThreshold INTEGER, sonetVTDefaultESBThreshold INTEGER, sonetVTDefaultSESThreshold INTEGER, sonetVTDefaultUASThreshold INTEGER, sonetVTDefaultPPJCGenThreshold INTEGER, sonetVTDefaultNPJCGenThreshold INTEGER, sonetVTDefaultPPJCDetThreshold INTEGER, sonetVTDefaultNPJCDetThreshold INTEGER, sonetVTDefaultPJCSGenThreshold INTEGER, sonetVTDefaultPJCSDetThreshold INTEGER, sonetVTDefaultPJCDiffThreshold INTEGER, sonetVTDefaultDayCVThreshold INTEGER, sonetVTDefaultDayESThreshold INTEGER, sonetVTDefaultDayESAThreshold INTEGER, sonetVTDefaultDayESBThreshold INTEGER, sonetVTDefaultDaySESThreshold INTEGER, sonetVTDefaultDayUASThreshold INTEGER, sonetVTDefaultDayPPJCGenThreshold INTEGER, sonetVTDefaultDayNPJCGenThreshold INTEGER, sonetVTDefaultDayPPJCDetThreshold INTEGER, sonetVTDefaultDayNPJCDetThreshold INTEGER, sonetVTDefaultDayPJCSGenThreshold INTEGER, sonetVTDefaultDayPJCSDetThreshold INTEGER, sonetVTDefaultDayPJCDiffThreshold INTEGER } sonetVTDefaultThresholdDirection OBJECT-TYPE SYNTAX INTEGER { nearEnd(1), farEnd(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The digital signal direction for which the default threshold values apply." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 1 } sonetVTDefaultThresholdRate OBJECT-TYPE SYNTAX INTEGER { vt1dot5(1), vtg(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION Expires January 1999 [Page 89] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 "The path digital signal rate for which the default threshold values apply." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 2 } sonetVTDefaultCVThreshold OBJECT-TYPE SYNTAX INTEGER (1..16383) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET CV-V and CV-VFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 3 } sonetVTDefaultESThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ES-V and ES-VFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 4 } sonetVTDefaultESAThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESA-V and ESA-VFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 5 } sonetVTDefaultESBThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESB-V and ESB-VFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 6 } sonetVTDefaultSESThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) Expires January 1999 [Page 90] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET SES-V and SES-VFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 7 } sonetVTDefaultUASThreshold OBJECT-TYPE SYNTAX INTEGER (1..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET UAS-V and UAS-VFE counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 8 } sonetVTDefaultPPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PPJC-VGen counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 9 } sonetVTDefaultNPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET NPJC-VGen counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 10 } sonetVTDefaultPPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PPJC-VDet counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 11 } Expires January 1999 [Page 91] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetVTDefaultNPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET NPJC-VDet counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 12 } sonetVTDefaultPJCSGenThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PJCS-VGen counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 13 } sonetVTDefaultPJCSDetThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PJCS-VDet counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 14 } sonetVTDefaultPJCDiffThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PJCDiff-V counter 15-minute interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 15 } sonetVTDefaultDayCVThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET CV-V and CV-VFE counter 1-day interval thresholds." Expires January 1999 [Page 92] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 16 } sonetVTDefaultDayESThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ES-V and ES-VFE counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 17 } sonetVTDefaultDayESAThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESA-V and ESA-VFE counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 18 } sonetVTDefaultDayESBThreshold OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET ESB-V and ESB-VFE counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 19 } sonetVTDefaultDaySESThreshold OBJECT-TYPE SYNTAX INTEGER (1..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET SES-V and SES-VFE counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 20 } sonetVTDefaultDayUASThreshold OBJECT-TYPE SYNTAX INTEGER (1..4095) MAX-ACCESS read-write STATUS current Expires January 1999 [Page 93] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 DESCRIPTION "The default value for SONET UAS-V and UAS-VFE counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 21 } sonetVTDefaultDayPPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (1..16777215) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PPJC-VGen counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 22 } sonetVTDefaultDayNPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (1..16777215) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET NPJC-VGen counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 23 } sonetVTDefaultDayPPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (1..16777215) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PPJC-VDet counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 24 } sonetVTDefaultDayNPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (1..16777215) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET NPJC-VDet counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 25 } sonetVTDefaultDayPJCSGenThreshold OBJECT-TYPE Expires January 1999 [Page 94] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PJCS-VGen counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 26 } sonetVTDefaultDayPJCSDetThreshold OBJECT-TYPE SYNTAX INTEGER (1..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PJCS-VDet counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 27 } sonetVTDefaultDayPJCDiffThreshold OBJECT-TYPE SYNTAX INTEGER (1..16777215) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value for SONET PJCDiff-V counter 1-day interval thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetVTDefaultThresholdEntry 28 } -- ********************************************************************* -- SONET Path threshold value object definitions. This table is an -- extension to the sonetVTCurrentTable found in the SONET-MIB. -- ********************************************************************* sonetVTThresholdTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetVTThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of trap threshold values for SONET Path counters." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSupVT 2 } sonetVTThresholdEntry OBJECT-TYPE SYNTAX SonetVTThresholdEntry MAX-ACCESS not-accessible Expires January 1999 [Page 95] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 STATUS current DESCRIPTION "An entry in the table of SONET Path trap thresholds." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." AUGMENTS { sonetVTCurrentEntry } ::= { sonetVTThresholdTable 1 } SonetVTThresholdEntry ::= SEQUENCE { sonetVTCurrentCVThreshold INTEGER, sonetVTCurrentESThreshold INTEGER, sonetVTCurrentESAThreshold INTEGER, sonetVTCurrentESBThreshold INTEGER, sonetVTCurrentSESThreshold INTEGER, sonetVTCurrentUASThreshold INTEGER, sonetVTCurrentPPJCGenThreshold INTEGER, sonetVTCurrentNPJCGenThreshold INTEGER, sonetVTCurrentPPJCDetThreshold INTEGER, sonetVTCurrentNPJCDetThreshold INTEGER, sonetVTCurrentPJCSGenThreshold INTEGER, sonetVTCurrentPJCSDetThreshold INTEGER, sonetVTCurrentPJCDiffThreshold INTEGER, sonetVTDayCVThreshold INTEGER, sonetVTDayESThreshold INTEGER, sonetVTDayESAThreshold INTEGER, sonetVTDayESBThreshold INTEGER, sonetVTDaySESThreshold INTEGER, sonetVTDayUASThreshold INTEGER, sonetVTDayPPJCGenThreshold INTEGER, sonetVTDayNPJCGenThreshold INTEGER, sonetVTDayPPJCDetThreshold INTEGER, sonetVTDayNPJCDetThreshold INTEGER, sonetVTDayPJCSGenThreshold INTEGER, sonetVTDayPJCSDetThreshold INTEGER, sonetVTDayPJCDiffThreshold INTEGER } sonetVTCurrentCVThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval CV-V and CV-VFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } Expires January 1999 [Page 96] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 ::= { sonetVTThresholdEntry 1 } sonetVTCurrentESThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval ES-V and ES-VFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 2 } sonetVTCurrentESAThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval ESA-V and ESA-VFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 3 } sonetVTCurrentESBThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval ESB-V and ESB-VFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 4 } sonetVTCurrentSESThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval SES-V and SES-VFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." Expires January 1999 [Page 97] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 DEFVAL { 0 } ::= { sonetVTThresholdEntry 5 } sonetVTCurrentUASThreshold OBJECT-TYPE SYNTAX INTEGER (0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval UAS-V and UAS-VFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 6 } sonetVTCurrentPPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval PPJC-VGen counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 7 } sonetVTCurrentNPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval NPJC-VGen counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 8 } sonetVTCurrentPPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval PPJC-VDet counter. A value of zero indicates that the default threshold value is to be used." Expires January 1999 [Page 98] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 9 } sonetVTCurrentNPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval NPJC-VDet counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 10 } sonetVTCurrentPJCSGenThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval PJCS-VGen counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 11 } sonetVTCurrentPJCSDetThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval PJCS-VDet counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 12 } sonetVTCurrentPJCDiffThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 15-minute interval PJCDiff-V counter. A value of zero indicates that the Expires January 1999 [Page 99] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 13 } sonetVTDayCVThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day CV-V and CV-VFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 14 } sonetVTDayESThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day ES-V and ES-VFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 15 } sonetVTDayESAThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day ESA-V and ESA-VFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 16 } sonetVTDayESBThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day Expires January 1999 [Page 100] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 ESB-V and ESB-VFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 17 } sonetVTDaySESThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day SES-V and SES-VFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 18 } sonetVTDayUASThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day UAS-V and UAS-VFE counters. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 19 } sonetVTDayPPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day interval PPJC-VGen counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 20 } sonetVTDayNPJCGenThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION Expires January 1999 [Page 101] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 "The trap threshold value for the interface's current 1-day interval NPJC-VGen counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 21 } sonetVTDayPPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day interval PPJC-VDet counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 22 } sonetVTDayNPJCDetThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day interval NPJC-VDet counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 23 } sonetVTDayPJCSGenThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day interval PJCS-VGen counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 24 } sonetVTDayPJCSDetThreshold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current Expires January 1999 [Page 102] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 DESCRIPTION "The trap threshold value for the interface's current 1-day interval PJCS-VDet counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 25 } sonetVTDayPJCDiffThreshold OBJECT-TYPE SYNTAX INTEGER (0..1048575) MAX-ACCESS read-write STATUS current DESCRIPTION "The trap threshold value for the interface's current 1-day interval PJCDiff-V counter. A value of zero indicates that the default threshold value is to be used." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." DEFVAL { 0 } ::= { sonetVTThresholdEntry 26 } -- ********************************************************************* -- Extension to the sonetVTCurrentTable found in the SONET-MIB. -- ********************************************************************* sonetSupVTCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSupVTCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Extension to the SONET Path Current table." ::= { sonetSupVT 3 } sonetSupVTCurrentEntry OBJECT-TYPE SYNTAX SonetSupVTCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Various extensions to an entry in the SONET Path Current table." AUGMENTS { sonetVTCurrentEntry } ::= { sonetSupVTCurrentTable 1 } SonetSupVTCurrentEntry ::= SEQUENCE { sonetVTSevereErrorThreshold Integer32, sonetVTResetCounters INTEGER, sonetVTCurrentStartTime DateAndTime, Expires January 1999 [Page 103] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetVTCurrentFCs PerfCurrentCount, sonetVTCurrentESAs PerfCurrentCount, sonetVTCurrentESBs PerfCurrentCount, sonetVTCurrentPPJCGens PerfCurrentCount, sonetVTCurrentNPJCGens PerfCurrentCount, sonetVTCurrentPPJCDets PerfCurrentCount, sonetVTCurrentNPJCDets PerfCurrentCount, sonetVTCurrentPJCSGens PerfCurrentCount, sonetVTCurrentPJCSDets PerfCurrentCount, sonetVTCurrentPJCDiffs PerfCurrentCount } sonetVTSevereErrorThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of VT-path EDC errors (V5 byte) in a 1-second interval at which point the condition is counted as a severe error. The value of this variable should correspond to the value indicated by sonetSESthresholdSet in the SONET-MIB. If sonetSESthresholdSet is set to other(1), this variable is the soul source of this information. This value applies to all near-end and far-end path SES counters." REFERENCE "ANSI T1.231-1997 clause 8.4.5.5." ::= { sonetSupVTCurrentEntry 1 } sonetVTResetCounters OBJECT-TYPE SYNTAX INTEGER { nearEndCurrent15Minute(1), nearEndCurrent1day(2), farEndCurrent15Minute(3), farEndCurrent1day(4), all(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "This varible provides the capability to initialize SONET near-end and far-end VT-path layer performance counters to zero (0) on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupVTCurrentEntry 2 } sonetVTCurrentStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only Expires January 1999 [Page 104] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 STATUS current DESCRIPTION "This variable indicates the date and time at which the current 15-minute interval of near-end VT-path measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupVTCurrentEntry 3 } sonetVTCurrentFCs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The near-end path failure count (FC-V) is the number of occurences of near-end path failure events encountered by the SONET path layer interface in the current 15-minute interval. A near-end path failure event begins when the first of any of LOP-V, AIS-V or UNEQ-V failures is declared; a near-end path failure event ends when all LOP-V, AIS-V and UNEQ-V failures have cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.8.1." ::= { sonetSupVTCurrentEntry 4 } sonetVTCurrentESAs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path errored second type A (ESA-V) count is the number of 1-second intervals containing one EDC error (V5 byte) and no AIS-V, LOP-V or UNEQ-V defects which were encountered by the SONET path layer interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.3." ::= { sonetSupVTCurrentEntry 5 } sonetVTCurrentESBs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path errored second type B (ESB-V) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold EDC errors (V5 byte), and no AIS-V, LOP-V or UNEQ-V defects which were encountered by the SONET path layer interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.4." Expires January 1999 [Page 105] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 ::= { sonetSupVTCurrentEntry 6 } sonetVTCurrentPPJCGens OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PPJC-VGen is a count of VT-path positive pointer justifications generated by the NE in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.1." ::= { sonetSupVTCurrentEntry 7 } sonetVTCurrentNPJCGens OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The NPJC-VGen is a count of VT-path negative pointer justifications generated by the NE in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.2." ::= { sonetSupVTCurrentEntry 8 } sonetVTCurrentPPJCDets OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PPJC-VDet is a count of VT-path positive pointer justifications detected by the NE in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.3." ::= { sonetSupVTCurrentEntry 9 } sonetVTCurrentNPJCDets OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The NPJC-VGen is a count of VT-path negative pointer justifications detected by the NE in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.4." ::= { sonetSupVTCurrentEntry 10 } sonetVTCurrentPJCSGens OBJECT-TYPE Expires January 1999 [Page 106] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCS-VGen is a count of 1-second intervals containing one or more VT-path pointer justification movements generated by the NE in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.8." ::= { sonetSupVTCurrentEntry 11 } sonetVTCurrentPJCSDets OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCS-VDet is a count of 1-second intervals containing one or more VT-path pointer justification movements detected by the NE in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.9." ::= { sonetSupVTCurrentEntry 12 } sonetVTCurrentPJCDiffs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCDiff-V is the absolute value of the difference between the net number of detected pointer movement counts and the net number of generated pointer movement counts in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.10." ::= { sonetSupVTCurrentEntry 13 } -- ******************************************************************* -- Extension to the sonetVTIntervalTable found in the SONET-MIB. -- ******************************************************************* sonetSupVTIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSupVTIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The extension to the SONET Path Interval table to add more counters." ::= { sonetSupVT 4 } Expires January 1999 [Page 107] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetSupVTIntervalEntry OBJECT-TYPE SYNTAX SonetSupVTIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An extension to an entry in the SONET Path Interval table." AUGMENTS { sonetVTIntervalEntry } ::= { sonetSupVTIntervalTable 1 } SonetSupVTIntervalEntry ::= SEQUENCE { sonetVTIntervalStartTime DateAndTime, sonetVTIntervalFCs PerfIntervalCount, sonetVTIntervalESAs PerfIntervalCount, sonetVTIntervalESBs PerfIntervalCount, sonetVTIntervalPPJCGens PerfIntervalCount, sonetVTIntervalNPJCGens PerfIntervalCount, sonetVTIntervalPPJCDets PerfIntervalCount, sonetVTIntervalNPJCDets PerfIntervalCount, sonetVTIntervalPJCSGens PerfIntervalCount, sonetVTIntervalPJCSDets PerfIntervalCount, sonetVTIntervalPJCDiffs PerfIntervalCount } sonetVTIntervalStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which this 15-minute interval of measurements began on this VT-path." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupVTIntervalEntry 1 } sonetVTIntervalFCs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The near-end path failure count (FC-V) is the number of occurences of near-end path failure events encountered by the SONET path layer interface in a previous 15-minute interval. A near-end path failure event begins when the first of any of LOP-V, AIS-V or UNEQ-V failures is declared; a near-end path failure event ends when all LOP-V, AIS-V and UNEQ-V failures have cleared." Expires January 1999 [Page 108] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 REFERENCE "ANSI T1.231-1997 clause 8.3.8.1." ::= { sonetSupVTIntervalEntry 2 } sonetVTIntervalESAs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path errored second type A (ESA-V) count is the number of 1-second intervals containing one EDC error (V5 byte) and no AIS-V, LOP-V or UNEQ-V defects which were encountered by the SONET path layer interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.3." ::= { sonetSupVTIntervalEntry 3 } sonetVTIntervalESBs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path errored second type B (ESB-V) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold EDC errors (V5 byte) and no AIS-V, LOP-V or UNEQ-V defects which were encountered by the SONET path layer interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.4." ::= { sonetSupVTIntervalEntry 4 } sonetVTIntervalPPJCGens OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PPJC-VGen is a count of VT-path positive pointer justifications generated by the NE in the previous or recent 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.1." ::= { sonetSupVTIntervalEntry 5 } sonetVTIntervalNPJCGens OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The NPJC-VGen is a count of VT-path negative pointer justifications generated by the NE in the previous or recent Expires January 1999 [Page 109] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.2." ::= { sonetSupVTIntervalEntry 6 } sonetVTIntervalPPJCDets OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PPJC-VDet is a count of VT-path positive pointer justifications detected by the NE in the previous or recent 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.3." ::= { sonetSupVTIntervalEntry 7 } sonetVTIntervalNPJCDets OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The NPJC-VGen is a count of VT-path negative pointer justifications detected by the NE in the previous or recent 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.4." ::= { sonetSupVTIntervalEntry 8 } sonetVTIntervalPJCSGens OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCS-VGen is a count of 1-second intervals containing one or more VT-path pointer justification movements generated by the NE in the previous or recent 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.8." ::= { sonetSupVTIntervalEntry 9 } sonetVTIntervalPJCSDets OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCS-VDet is a count of 1-second intervals containing one or more VT-path pointer justification movements detected by the NE in the previous or recent 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.9." ::= { sonetSupVTIntervalEntry 10 } Expires January 1999 [Page 110] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetVTIntervalPJCDiffs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCDiff-V is the absolute value of the difference between the net number of detected pointer movement counts and the net number of generated pointer movement counts in the previous or recent 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.10." ::= { sonetSupVTIntervalEntry 11 } -- ******************************************************************* -- The SONET Path Day Table. -- ******************************************************************* sonetVTDayTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetVTDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET Path Day table. Contains performance statistics collected by each SONET Path over multiple 1-day intervals of operation." ::= { sonetSupVT 17 } sonetVTDayEntry OBJECT-TYPE SYNTAX SonetVTDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET Path Day table." INDEX { ifIndex, sonetVTDayNumber } ::= { sonetVTDayTable 1 } SonetVTDayEntry ::= SEQUENCE { sonetVTDayNumber INTEGER, sonetVTDayStartTime DateAndTime, sonetVTDayValidData TruthValue, sonetVTDayFCs PerfDayCount, sonetVTDayCVs PerfDayCount, sonetVTDayESs PerfDayCount, sonetVTDayESAs PerfDayCount, sonetVTDayESBs PerfDayCount, sonetVTDaySESs PerfDayCount, Expires January 1999 [Page 111] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetVTDayUASs PerfDayCount, sonetVTDayPPJCGens PerfDayCount, sonetVTDayNPJCGens PerfDayCount, sonetVTDayPPJCDets PerfDayCount, sonetVTDayNPJCDets PerfDayCount, sonetVTDayPJCSGens PerfDayCount, sonetVTDayPJCSDets PerfDayCount, sonetVTDayPJCDiffs PerfDayCount } sonetVTDayNumber OBJECT-TYPE SYNTAX INTEGER (1..33) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number which identifies the 1-day interval for which the set of near-end path related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval." REFERENCE "ANSI T1.231-1997 clause 9.1.2.1." ::= { sonetVTDayEntry 1 } sonetVTDayStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which the 1-day interval of measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.2.1." ::= { sonetVTDayEntry 2 } sonetVTDayValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is missing." REFERENCE "ANSI T1.231-1997 clause 9.1.2.2." Expires January 1999 [Page 112] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 ::= { sonetVTDayEntry 3 } sonetVTDayFCs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The near-end path failure count (FC-V) is the number of occurences of near-end path failure events encountered by the SONET path layer interface in a previous 1-day interval. A near-end path failure event begins when the first of any of LOP-V, AIS-V or UNEQ-V failures is declared; a near-end path failure event ends when all LOP-V, AIS-V and UNEQ-V failures have cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.8.1." ::= { sonetVTDayEntry 4 } sonetVTDayCVs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path code violation (CV-V) count is the number of BIP-2 errors which were detected at the VT-path layer interface in a previous 1-day interval. CVs for the path layer are collected using the BIP-2 in the V5 byte located in the VT-path overhead." REFERENCE "ANSI T1.231-1997 clause 8.4.5.1.1." ::= { sonetVTDayEntry 5 } sonetVTDayESs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path errored second (ES-V) count is the number of 1-second intervals containing one or more EDC error (V5 byte), or one or more AIS-V, LOP-V or UNEQ-V defects which were encountered by the SONET path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.2." ::= { sonetVTDayEntry 6 } sonetVTDayESAs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current Expires January 1999 [Page 113] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 DESCRIPTION "The path errored second type A (ESA-V) count is the number of 1-second intervals containing one EDC error (V5 byte) and no AIS-V, LOP-V or UNEQ-V defects which were encountered by the SONET path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.3." ::= { sonetVTDayEntry 7 } sonetVTDayESBs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path errored second type B (ESB-V) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold EDC errors (V5 byte) and no AIS-V, LOP-V or UNEQ-V defects which were encountered by the SONET path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.4." ::= { sonetVTDayEntry 8 } sonetVTDaySESs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path severely errored second (SES-V) is a count of 1-second intervals containing sonetSevereErrorThreshold or more EDC error (V5 byte), or one or more AIS-V, LOP-V or UNEQ-V defects which were encountered by the SONET path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.5." ::= { sonetVTDayEntry 9 } sonetVTDayUASs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The path unavailable second (UAS-V) is a count of 1-second intervals for which the SONET VT-path was unavailable during a previous 1-day interval. The SONET VT-path becomes unavailable at the onset of 10 contiguous SES-Vs. The 10 SES-Vs are included in unavailable time. Once unavailable, the SONET VT-path becomes available at the onset of 10 contiguous seconds with no SES-Vs. The 10 seconds with no SES-Vs are excluded from unavailable time." Expires January 1999 [Page 114] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 REFERENCE "ANSI T1.231-1997 clause 8.4.5.6." ::= { sonetVTDayEntry 10 } sonetVTDayPPJCGens OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PPJC-VGen is a count of VT-path positive pointer justifications generated by the NE in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.1." ::= { sonetVTDayEntry 11 } sonetVTDayNPJCGens OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The NPJC-VGen is a count of VT-path negative pointer justifications generated by the NE in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.2." ::= { sonetVTDayEntry 12 } sonetVTDayPPJCDets OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PPJC-VDet is a count of VT-path positive pointer justifications detected by the NE in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.3." ::= { sonetVTDayEntry 13 } sonetVTDayNPJCDets OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The NPJC-VGen is a count of VT-path negative pointer justifications detected by the NE in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.7.4." ::= { sonetVTDayEntry 14 } sonetVTDayPJCSGens OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current Expires January 1999 [Page 115] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 DESCRIPTION "The PJCS-VGen is a count of 1-second intervals containing one or more VT-path pointer justification movements generated by the NE in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.8." ::= { sonetVTDayEntry 15 } sonetVTDayPJCSDets OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCS-VDet is a count of 1-second intervals containing one or more VT-path pointer justification movements detected by the NE in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.9." ::= { sonetVTDayEntry 16 } sonetVTDayPJCDiffs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The PJCDiff-V is the absolute value of the difference between the net number of detected pointer movement counts and the net number of generated pointer movement counts in the 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5.10." ::= { sonetVTDayEntry 17 } -- ******************************************************************* -- Extension to the sonetFarEndVTCurrentTable found in the -- SONET-MIB. -- ******************************************************************* sonetSupFarEndVTCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSupFarEndVTCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The extension to the SONET Far End Path Current table to add more counters." ::= { sonetSupFarEndVT 1 } sonetSupFarEndVTCurrentEntry OBJECT-TYPE SYNTAX SonetSupFarEndVTCurrentEntry Expires January 1999 [Page 116] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 MAX-ACCESS not-accessible STATUS current DESCRIPTION "An extension to an entry in the SONET Far End Path Current table." AUGMENTS { sonetFarEndVTCurrentEntry } ::= { sonetSupFarEndVTCurrentTable 1 } SonetSupFarEndVTCurrentEntry ::= SEQUENCE { sonetFarEndVTCurrentStartTime DateAndTime, sonetFarEndVTCurrentFCs PerfCurrentCount, sonetFarEndVTCurrentESAs PerfCurrentCount, sonetFarEndVTCurrentESBs PerfCurrentCount } sonetFarEndVTCurrentStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which the current 15-minute interval of measurements began on this Far End Path." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupFarEndVTCurrentEntry 1 } sonetFarEndVTCurrentFCs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path failure count (FC-VFE) is the number of occurences of far-end path failure events detected by the SONET VT-path layer interface in the current 15-minute interval. A far-end path failure event begins when the first of any remote failure indication (RFI-V, RFI-V server, or RFI-V connectivity) failure is declared; a far-end path failure event ends when all RFI-V, RFI-V server, or RFI-V connectivity failures are cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.8.2." ::= { sonetSupFarEndVTCurrentEntry 2 } sonetFarEndVTCurrentESAs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION Expires January 1999 [Page 117] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 "The far-end path errored second type A (ESA-VFE) count is the number of 1-second intervals containing one REDC-V and no RDI-V, ERDI-V server or ERDI-V connectivity defects which were detected by the SONET VT-path layer interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetSupFarEndVTCurrentEntry 3 } sonetFarEndVTCurrentESBs OBJECT-TYPE SYNTAX PerfCurrentCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path errored second type B (ESB-VFE) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold REDC-Vs and no RDI-V, ERDI-V server or ERDI-V connectivity defects which were detected by the SONET VT-path layer interface in the current 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetSupFarEndVTCurrentEntry 4 } -- ******************************************************************* -- Extension to the sonetFarEndVTIntervalTable found in the -- SONET-MIB. -- ******************************************************************* sonetSupFarEndVTIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetSupFarEndVTIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The extension to the SONET Far End Path Interval table to add more counters." ::= { sonetSupFarEndVT 2 } sonetSupFarEndVTIntervalEntry OBJECT-TYPE SYNTAX SonetSupFarEndVTIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An extension to an entry in the SONET Far End Path Interval table." AUGMENTS { sonetFarEndVTIntervalEntry } ::= { sonetSupFarEndVTIntervalTable 1 } SonetSupFarEndVTIntervalEntry ::= Expires January 1999 [Page 118] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 SEQUENCE { sonetFarEndVTIntervalStartTime DateAndTime, sonetFarEndVTIntervalFCs PerfIntervalCount, sonetFarEndVTIntervalESAs PerfIntervalCount, sonetFarEndVTIntervalESBs PerfIntervalCount } sonetFarEndVTIntervalStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which this 15-minute interval of far-end path measurements began on this interface." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupFarEndVTIntervalEntry 1 } sonetFarEndVTIntervalFCs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path failure count (FC-VFE) is the number of occurences of far-end path failure events detected by the SONET VT-path layer interface in a previous 15-minute interval. A far-end path failure event begins when the first of any remote failure indication (RFI-V, RFI-V server, or RFI-V connectivity) failure is declared; a far-end path failure event ends when all RFI-V, RFI-V server, or RFI-V connectivity failures are cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.8.2." ::= { sonetSupFarEndVTIntervalEntry 2 } sonetFarEndVTIntervalESAs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path errored second type A (ESA-VFE) count is the number of 1-second intervals containing one REDC-V and no RDI-V, ERDI-V server or ERDI-V connectivity defects which were detected by the SONET VT-path layer interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetSupFarEndVTIntervalEntry 3 } Expires January 1999 [Page 119] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetFarEndVTIntervalESBs OBJECT-TYPE SYNTAX PerfIntervalCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path errored second type B (ESB-VFE) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold REDC-Vs, and no RDI-V, ERDI-V server or ERDI-V connectivity defects which were detected by the SONET VT-path layer interface in a previous 15-minute interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetSupFarEndVTIntervalEntry 4 } -- ******************************************************************* -- The SONET Far End Path Day Table. -- ******************************************************************* sonetFarEndVTDayTable OBJECT-TYPE SYNTAX SEQUENCE OF SonetFarEndVTDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SONET Far End Path Day table. Contains various statistics collected by each SONET Far End Path over multiple 1-day intervals of operation." ::= { sonetSupFarEndVT 3 } sonetFarEndVTDayEntry OBJECT-TYPE SYNTAX SonetFarEndVTDayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the SONET Far End Path Day table." INDEX { ifIndex, sonetFarEndVTDayNumber } ::= { sonetFarEndVTDayTable 1 } SonetFarEndVTDayEntry ::= SEQUENCE { sonetFarEndVTDayNumber INTEGER, sonetFarEndVTDayStartTime DateAndTime, sonetFarEndVTDayValidData TruthValue, sonetFarEndVTDayFCs PerfDayCount, sonetFarEndVTDayCVs PerfDayCount, sonetFarEndVTDayESs PerfDayCount, sonetFarEndVTDayESAs PerfDayCount, sonetFarEndVTDayESBs PerfDayCount, Expires January 1999 [Page 120] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetFarEndVTDaySESs PerfDayCount, sonetFarEndVTDayUASs PerfDayCount } sonetFarEndVTDayNumber OBJECT-TYPE SYNTAX INTEGER (1..4) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number which identifies the 1-day interval for which the set of far-end VT-path related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval." REFERENCE "ANSI T1.231-1997 clause 9.1.2.1." ::= { sonetFarEndVTDayEntry 1 } sonetFarEndVTDayStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the date and time at which the current interval of measurements began." REFERENCE "ANSI T1.231-1997 clause 9.1.2.1." ::= { sonetFarEndVTDayEntry 2 } sonetFarEndVTDayValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is missing (e.g., when a near-end defect prevents some far-end data from being collected)." REFERENCE "ANSI T1.231-1997 clause 9.1.2.2." ::= { sonetFarEndVTDayEntry 3 } sonetFarEndVTDayFCs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only Expires January 1999 [Page 121] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 STATUS current DESCRIPTION "The far-end path failure count (FC-VFE) is the number of occurences of far-end path failure events detected by the SONET VT-path layer interface in a previous 1-day interval. A far-end path failure event begins when the first of any remote failure indication (RFI-V, RFI-V server, or RFI-V connectivity) failure is declared; a far-end path failure event ends when all RFI-V, RFI-V server, or RFI-V connectivity failures are cleared." REFERENCE "ANSI T1.231-1997 clause 8.3.8.2." ::= { sonetFarEndVTDayEntry 4 } sonetFarEndVTDayCVs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path code violation (CV-VFE) count is the number of REI-Vs (bit 1-4 in G1 byte) which were detected at the SONET VT-path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetFarEndVTDayEntry 5 } sonetFarEndVTDayESs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path errored second (ES-VFE) count is the number of 1-second intervals containing one or more REDC-V, or one or more RDI-V, ERDI-V server or ERDI-V connectivity defects which were encountered by the SONET VT-path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetFarEndVTDayEntry 6 } sonetFarEndVTDayESAs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path errored second type A (ESA-VFE) count is the number of 1-second intervals containing one REDC-V and no RDI-V, ERDI-V server or ERDI-V connectivity defects which were detected by the SONET VT-path layer interface in a previous 1-day interval." Expires January 1999 [Page 122] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetFarEndVTDayEntry 7 } sonetFarEndVTDayESBs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path errored second type B (ESB-VFE) is a count of 1-second intervals containing more than one but less than sonetSevereErrorThreshold REDC-Vs and no RDI-V, ERDI-V server or ERDI-V connectivity defects which were detected by the SONET VT-path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.6." ::= { sonetFarEndVTDayEntry 8 } sonetFarEndVTDaySESs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path severely errored second (SES-VFE) is a count of 1-second intervals containing sonetSevereErrorThreshold or more REDC-Vs or one or more RDI-V, ERDI-V server or ERDI-V connectivity defects which were detected by the SONET VT-path layer interface in a previous 1-day interval." REFERENCE "ANSI T1.231-1997 clause 8.4.5." ::= { sonetFarEndVTDayEntry 9 } sonetFarEndVTDayUASs OBJECT-TYPE SYNTAX PerfDayCount MAX-ACCESS read-only STATUS current DESCRIPTION "The far-end path unavailable second (UAS-VFE) is a count of 1-second intervals for which the SONET VT-path was unavailable during a previous 1-day interval. The SONET VT-path becomes unavailable at the onset of 10 contiguous SES-VFEs. The 10 SES-VFEs are included in unavailable time. Once unavailable, the SONET VT-path becomes available at the onset of 10 contiguous seconds with no SES-VFEs. The 10 seconds with no SES-VFEs are excluded from unavailable time." REFERENCE "ANSI T1.231-1997 clause 8.4.5.1." ::= { sonetFarEndVTDayEntry 10 } -- ********************************************************************* Expires January 1999 [Page 123] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 -- SONET notification and notification information definitions. -- ********************************************************************* sonetTrap OBJECT IDENTIFIER ::= { sonetSupObjects 6 } sonetTraps OBJECT IDENTIFIER ::= { sonetSupObjects 7 } sonetCounterId OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only -- accessible-for-notify STATUS current DESCRIPTION "The OBJECT IDENTIFIER of the instance of the SONET counter that has crossed its threshold." REFERENCE "ANSI T1.231-1997 clause 9.1.3." ::= { sonetTrap 1 } sonetCounterValue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only -- accessible-for-notify STATUS current DESCRIPTION "The current value of the SONET counter that has crossed its threshold." REFERENCE "ANSI T1.231-1997 clause 9.1.3." ::= { sonetTrap 2 } sonetThresholdCrossing NOTIFICATION-TYPE OBJECTS { sonetCounterId, sonetCounterValue } STATUS current DESCRIPTION "This notification signifies that a counter has crossed its designated threshold. The term 'threshold crossing' means that a threshold has been reached or exceeded. A threshold crossing alert message (trap) signifies a performance degredation at or above the preset threshold value." REFERENCE "ANSI T1.231-1997 clause 9.1.3." ::= { sonetTraps 1 } -- ******************************************************************* -- Conformance information -- ******************************************************************* sonetSupConformance OBJECT IDENTIFIER ::= { sonetSupplementalMIB 4 } sonetSupGroups OBJECT IDENTIFIER ::= { sonetSupConformance 1 } Expires January 1999 [Page 124] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetSupCompliances OBJECT IDENTIFIER ::= { sonetSupConformance 2 } -- ******************************************************************* -- MIB groupings - units of conformance -- ******************************************************************* sonetResetCountersGroup OBJECT-GROUP OBJECTS { sonetResetAllCounters, sonetMediumResetCounters, sonetSectionResetCounters, sonetLineResetCounters, sonetPathResetCounters, sonetVTResetCounters } STATUS current DESCRIPTION "The group of parameters used to reset the SONET counters." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupGroups 1 } sonetThresholdGroup OBJECT-GROUP OBJECTS { sonetThresholdTrapEnable, sonetPortThresholdTrapEnable, sonetSectionDefaultCVThreshold, sonetSectionDefaultESThreshold, sonetSectionDefaultESAThreshold, sonetSectionDefaultESBThreshold, sonetSectionDefaultSESThreshold, sonetSectionDefaultSEFSThreshold, sonetSectionCurrentCVThreshold, sonetSectionCurrentESThreshold, sonetSectionCurrentESAThreshold, sonetSectionCurrentESBThreshold, sonetSectionCurrentSESThreshold, sonetSectionCurrentSEFSThreshold, sonetLineDefaultCVThreshold, sonetLineDefaultESThreshold, sonetLineDefaultESAThreshold, sonetLineDefaultESBThreshold, sonetLineDefaultSESThreshold, sonetLineDefaultAISSThreshold, sonetLineDefaultUASThreshold, sonetLineCurrentCVThreshold, sonetLineCurrentESThreshold, sonetLineCurrentESAThreshold, sonetLineCurrentESBThreshold, sonetLineCurrentSESThreshold, Expires January 1999 [Page 125] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetLineCurrentAISSThreshold, sonetLineCurrentUASThreshold } STATUS current DESCRIPTION "SONET extensions to support thresholding and alerting on current 15-minute intervals." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSupGroups 2 } sonetDayThresholdGroup OBJECT-GROUP OBJECTS { sonetSectionDefaultDayCVThreshold, sonetSectionDefaultDayESThreshold, sonetSectionDefaultDayESAThreshold, sonetSectionDefaultDayESBThreshold, sonetSectionDefaultDaySESThreshold, sonetSectionDefaultDaySEFSThreshold, sonetSectionDayCVThreshold, sonetSectionDayESThreshold, sonetSectionDayESAThreshold, sonetSectionDayESBThreshold, sonetSectionDaySESThreshold, sonetSectionDaySEFSThreshold, sonetLineDefaultDayCVThreshold, sonetLineDefaultDayESThreshold, sonetLineDefaultDayESAThreshold, sonetLineDefaultDayESBThreshold, sonetLineDefaultDaySESThreshold, sonetLineDefaultDayAISSThreshold, sonetLineDefaultDayUASThreshold, sonetLineDayCVThreshold, sonetLineDayESThreshold, sonetLineDayESAThreshold, sonetLineDayESBThreshold, sonetLineDaySESThreshold, sonetLineDayAISSThreshold, sonetLineDayUASThreshold } STATUS current DESCRIPTION "SONET extensions to support thresholding and alerting on current 1-day intervals." REFERENCE "ANSI T1.231-1997 clause 9.1.5.2." ::= { sonetSupGroups 3 } sonetStartTimeGroup OBJECT-GROUP OBJECTS { sonetMediumCurrentStartTime, sonetMediumIntervalStartTime, sonetSectionCurrentStartTime, Expires January 1999 [Page 126] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetSectionIntervalStartTime, sonetLineCurrentStartTime, sonetLineIntervalStartTime, sonetFarEndLineCurrentStartTime, sonetFarEndLineIntervalStartTime, sonetPathCurrentStartTime, sonetPathIntervalStartTime, sonetFarEndPathCurrentStartTime, sonetFarEndPathIntervalStartTime, sonetVTCurrentStartTime, sonetVTIntervalStartTime, sonetFarEndVTCurrentStartTime, sonetFarEndVTIntervalStartTime } STATUS current DESCRIPTION "The SONET 15-minute interval time-stamp group." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupGroups 4 } sonetStartOfDayGroup OBJECT-GROUP OBJECTS { sonetStartOfDay } STATUS current DESCRIPTION "The start-of-day variable." REFERENCE "ANSI T1.231-1997 clause 9.1.5.1." ::= { sonetSupGroups 5 } sonetSupMediumGroup OBJECT-GROUP OBJECTS { sonetMediumCurrentLOSSs, sonetMediumIntervalValidData, sonetMediumIntervalLOSSs } STATUS current DESCRIPTION "The medium-related extensions to the SONET MIB." ::= { sonetSupGroups 6 } sonetMediumDayGroup OBJECT-GROUP OBJECTS { sonetMediumDayTimeElapsed, sonetMediumValidDays, sonetMediumInvalidDays, sonetMediumDayStartTime, sonetMediumDayValidData, sonetMediumDayLOSSs } STATUS current DESCRIPTION "The objects which are used to present the SONET Media 1-day interval counters." Expires January 1999 [Page 127] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 ::= { sonetSupGroups 7 } sonetSupSectionGroup OBJECT-GROUP OBJECTS { sonetSectionSevereErrorThreshold, sonetSectionCurrentESAs, sonetSectionCurrentESBs, sonetSectionIntervalESAs, sonetSectionIntervalESBs } STATUS current DESCRIPTION "The section-related extensions to the SONET MIB." ::= { sonetSupGroups 8 } sonetSectionDayGroup OBJECT-GROUP OBJECTS { sonetSectionDayStartTime, sonetSectionDayValidData, sonetSectionDayCVs, sonetSectionDayESs, sonetSectionDayESAs, sonetSectionDayESBs, sonetSectionDaySESs, sonetSectionDaySEFSs } STATUS current DESCRIPTION "The objects which are used to present the SONET Section 1-day interval counters." ::= { sonetSupGroups 9 } sonetSupLineGroup OBJECT-GROUP OBJECTS { sonetLineSevereErrorThreshold, sonetLineCurrentFCs, sonetLineCurrentESAs, sonetLineCurrentESBs, sonetLineCurrentAISSs, sonetLineIntervalFCs, sonetLineIntervalESAs, sonetLineIntervalESBs, sonetLineIntervalAISSs } STATUS current DESCRIPTION "The line-related extensions to the SONET MIB." ::= { sonetSupGroups 10 } sonetLineDayGroup OBJECT-GROUP OBJECTS { sonetLineDayStartTime, sonetLineDayValidData, sonetLineDayFCs, Expires January 1999 [Page 128] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetLineDayCVs, sonetLineDayESs, sonetLineDayESAs, sonetLineDayESBs, sonetLineDaySESs, sonetLineDayAISSs, sonetLineDayUASs } STATUS current DESCRIPTION "The objects which are used to present the SONET Line 1-day interval counters." ::= { sonetSupGroups 11 } sonetSupFarEndLineGroup OBJECT-GROUP OBJECTS { sonetFarEndLineCurrentFCs, sonetFarEndLineCurrentESAs, sonetFarEndLineCurrentESBs, sonetFarEndLineCurrentAISSs, sonetFarEndLineIntervalFCs, sonetFarEndLineIntervalESAs, sonetFarEndLineIntervalESBs, sonetFarEndLineIntervalAISSs } STATUS current DESCRIPTION "The far end line-related extensions to the SONET MIB." ::= { sonetSupGroups 12 } sonetFarEndLineDayGroup OBJECT-GROUP OBJECTS { sonetFarEndLineDayStartTime, sonetFarEndLineDayValidData, sonetFarEndLineDayFCs, sonetFarEndLineDayCVs, sonetFarEndLineDayESs, sonetFarEndLineDayESAs, sonetFarEndLineDayESBs, sonetFarEndLineDaySESs, sonetFarEndLineDayAISSs, sonetFarEndLineDayUASs } STATUS current DESCRIPTION "The objects which are used to present the SONET Far End Line 1-day interval counters." ::= { sonetSupGroups 13 } sonetPathThresholdGroup OBJECT-GROUP OBJECTS { sonetPathDefaultCVThreshold, sonetPathDefaultESThreshold, Expires January 1999 [Page 129] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetPathDefaultESAThreshold, sonetPathDefaultESBThreshold, sonetPathDefaultSESThreshold, sonetPathDefaultUASThreshold, sonetPathDefaultPPJCGenThreshold, sonetPathDefaultNPJCGenThreshold, sonetPathDefaultPPJCDetThreshold, sonetPathDefaultNPJCDetThreshold, sonetPathDefaultPJCSGenThreshold, sonetPathDefaultPJCSDetThreshold, sonetPathDefaultPJCDiffThreshold, sonetPathCurrentCVThreshold, sonetPathCurrentESThreshold, sonetPathCurrentESAThreshold, sonetPathCurrentESBThreshold, sonetPathCurrentSESThreshold, sonetPathCurrentUASThreshold, sonetPathCurrentPPJCGenThreshold, sonetPathCurrentNPJCGenThreshold, sonetPathCurrentPPJCDetThreshold, sonetPathCurrentNPJCDetThreshold, sonetPathCurrentPJCSGenThreshold, sonetPathCurrentPJCSDetThreshold, sonetPathCurrentPJCDiffThreshold } STATUS current DESCRIPTION "The extensions to the SONET MIB to provide path 15-minute interval thresholds." ::= { sonetSupGroups 14 } sonetPathDayThresholdGroup OBJECT-GROUP OBJECTS { sonetPathDefaultDayCVThreshold, sonetPathDefaultDayESThreshold, sonetPathDefaultDayESAThreshold, sonetPathDefaultDayESBThreshold, sonetPathDefaultDaySESThreshold, sonetPathDefaultDayUASThreshold, sonetPathDefaultDayPPJCGenThreshold, sonetPathDefaultDayNPJCGenThreshold, sonetPathDefaultDayPPJCDetThreshold, sonetPathDefaultDayNPJCDetThreshold, sonetPathDefaultDayPJCSGenThreshold, sonetPathDefaultDayPJCSDetThreshold, sonetPathDefaultDayPJCDiffThreshold, sonetPathDayCVThreshold, sonetPathDayESThreshold, sonetPathDayESAThreshold, Expires January 1999 [Page 130] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetPathDayESBThreshold, sonetPathDaySESThreshold, sonetPathDayUASThreshold, sonetPathDayPPJCGenThreshold, sonetPathDayNPJCGenThreshold, sonetPathDayPPJCDetThreshold, sonetPathDayNPJCDetThreshold, sonetPathDayPJCSGenThreshold, sonetPathDayPJCSDetThreshold, sonetPathDayPJCDiffThreshold } STATUS current DESCRIPTION "The extensions to the SONET MIB to provide path 1-day interval thresholds." ::= { sonetSupGroups 15 } sonetSupPathGroup OBJECT-GROUP OBJECTS { sonetPathSevereErrorThreshold, sonetPathCurrentFCs, sonetPathCurrentESAs, sonetPathCurrentESBs, sonetPathCurrentPPJCGens, sonetPathCurrentNPJCGens, sonetPathCurrentPPJCDets, sonetPathCurrentNPJCDets, sonetPathCurrentPJCSGens, sonetPathCurrentPJCSDets, sonetPathCurrentPJCDiffs, sonetPathIntervalFCs, sonetPathIntervalESAs, sonetPathIntervalESBs, sonetPathIntervalPPJCGens, sonetPathIntervalNPJCGens, sonetPathIntervalPPJCDets, sonetPathIntervalNPJCDets, sonetPathIntervalPJCSGens, sonetPathIntervalPJCSDets, sonetPathIntervalPJCDiffs } STATUS current DESCRIPTION "The extensions to the sonetPathCurrentTable and the sonetPathIntervalTable." ::= { sonetSupGroups 16 } sonetPathDayGroup OBJECT-GROUP OBJECTS { sonetPathDayStartTime, sonetPathDayValidData, Expires January 1999 [Page 131] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetPathDayFCs, sonetPathDayCVs, sonetPathDayESs, sonetPathDayESAs, sonetPathDayESBs, sonetPathDaySESs, sonetPathDayUASs, sonetPathDayPPJCGens, sonetPathDayNPJCGens, sonetPathDayPPJCDets, sonetPathDayNPJCDets, sonetPathDayPJCSGens, sonetPathDayPJCSDets, sonetPathDayPJCDiffs } STATUS current DESCRIPTION "The objects which are used to present the SONET Path 1-day interval counters." ::= { sonetSupGroups 17 } sonetSupFarEndPathGroup OBJECT-GROUP OBJECTS { sonetFarEndPathCurrentFCs, sonetFarEndPathCurrentESAs, sonetFarEndPathCurrentESBs, sonetFarEndPathIntervalFCs, sonetFarEndPathIntervalESAs, sonetFarEndPathIntervalESBs } STATUS current DESCRIPTION "The extensions to the sonetFarEndPathIntervalTable." ::= { sonetSupGroups 18 } sonetFarEndPathDayGroup OBJECT-GROUP OBJECTS { sonetFarEndPathDayStartTime, sonetFarEndPathDayValidData, sonetFarEndPathDayFCs, sonetFarEndPathDayCVs, sonetFarEndPathDayESs, sonetFarEndPathDayESAs, sonetFarEndPathDayESBs, sonetFarEndPathDaySESs, sonetFarEndPathDayUASs } STATUS current DESCRIPTION "The objects which are used to present the SONET Far End Path 1-day interval counters." ::= { sonetSupGroups 19 } Expires January 1999 [Page 132] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetVTThresholdGroup OBJECT-GROUP OBJECTS { sonetVTDefaultCVThreshold, sonetVTDefaultESThreshold, sonetVTDefaultESAThreshold, sonetVTDefaultESBThreshold, sonetVTDefaultSESThreshold, sonetVTDefaultUASThreshold, sonetVTDefaultPPJCGenThreshold, sonetVTDefaultNPJCGenThreshold, sonetVTDefaultPPJCDetThreshold, sonetVTDefaultNPJCDetThreshold, sonetVTDefaultPJCSGenThreshold, sonetVTDefaultPJCSDetThreshold, sonetVTDefaultPJCDiffThreshold, sonetVTCurrentCVThreshold, sonetVTCurrentESThreshold, sonetVTCurrentESAThreshold, sonetVTCurrentESBThreshold, sonetVTCurrentSESThreshold, sonetVTCurrentUASThreshold, sonetVTCurrentPPJCGenThreshold, sonetVTCurrentNPJCGenThreshold, sonetVTCurrentPPJCDetThreshold, sonetVTCurrentNPJCDetThreshold, sonetVTCurrentPJCSGenThreshold, sonetVTCurrentPJCSDetThreshold, sonetVTCurrentPJCDiffThreshold } STATUS current DESCRIPTION "The extensions to the SONET MIB to provide path 15-minute interval thresholds." ::= { sonetSupGroups 20 } sonetVTDayThresholdGroup OBJECT-GROUP OBJECTS { sonetVTDefaultDayCVThreshold, sonetVTDefaultDayESThreshold, sonetVTDefaultDayESAThreshold, sonetVTDefaultDayESBThreshold, sonetVTDefaultDaySESThreshold, sonetVTDefaultDayUASThreshold, sonetVTDefaultDayPPJCGenThreshold, sonetVTDefaultDayNPJCGenThreshold, sonetVTDefaultDayPPJCDetThreshold, sonetVTDefaultDayNPJCDetThreshold, sonetVTDefaultDayPJCSGenThreshold, sonetVTDefaultDayPJCSDetThreshold, sonetVTDefaultDayPJCDiffThreshold, Expires January 1999 [Page 133] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetVTDayCVThreshold, sonetVTDayESThreshold, sonetVTDayESAThreshold, sonetVTDayESBThreshold, sonetVTDaySESThreshold, sonetVTDayUASThreshold, sonetVTDayPPJCGenThreshold, sonetVTDayNPJCGenThreshold, sonetVTDayPPJCDetThreshold, sonetVTDayNPJCDetThreshold, sonetVTDayPJCSGenThreshold, sonetVTDayPJCSDetThreshold, sonetVTDayPJCDiffThreshold } STATUS current DESCRIPTION "The extensions to the SONET MIB to provide path 1-day interval thresholds." ::= { sonetSupGroups 21 } sonetSupVTGroup OBJECT-GROUP OBJECTS { sonetVTSevereErrorThreshold, sonetVTCurrentFCs, sonetVTCurrentESAs, sonetVTCurrentESBs, sonetVTCurrentPPJCGens, sonetVTCurrentNPJCGens, sonetVTCurrentPPJCDets, sonetVTCurrentNPJCDets, sonetVTCurrentPJCSGens, sonetVTCurrentPJCSDets, sonetVTCurrentPJCDiffs, sonetVTIntervalFCs, sonetVTIntervalESAs, sonetVTIntervalESBs, sonetVTIntervalPPJCGens, sonetVTIntervalNPJCGens, sonetVTIntervalPPJCDets, sonetVTIntervalNPJCDets, sonetVTIntervalPJCSGens, sonetVTIntervalPJCSDets, sonetVTIntervalPJCDiffs } STATUS current DESCRIPTION "The extensions to the sonetVTCurrentTable and the sonetVTIntervalTable." ::= { sonetSupGroups 22 } Expires January 1999 [Page 134] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 sonetVTDayGroup OBJECT-GROUP OBJECTS { sonetVTDayStartTime, sonetVTDayValidData, sonetVTDayFCs, sonetVTDayCVs, sonetVTDayESs, sonetVTDayESAs, sonetVTDayESBs, sonetVTDaySESs, sonetVTDayUASs, sonetVTDayPPJCGens, sonetVTDayNPJCGens, sonetVTDayPPJCDets, sonetVTDayNPJCDets, sonetVTDayPJCSGens, sonetVTDayPJCSDets, sonetVTDayPJCDiffs } STATUS current DESCRIPTION "The objects which are used to present the SONET Path 1-day interval counters." ::= { sonetSupGroups 23 } sonetSupFarEndVTGroup OBJECT-GROUP OBJECTS { sonetFarEndVTCurrentFCs, sonetFarEndVTCurrentESAs, sonetFarEndVTCurrentESBs, sonetFarEndVTIntervalFCs, sonetFarEndVTIntervalESAs, sonetFarEndVTIntervalESBs } STATUS current DESCRIPTION "The extensions to the sonetFarEndVTIntervalTable." ::= { sonetSupGroups 24 } sonetFarEndVTDayGroup OBJECT-GROUP OBJECTS { sonetFarEndVTDayStartTime, sonetFarEndVTDayValidData, sonetFarEndVTDayFCs, sonetFarEndVTDayCVs, sonetFarEndVTDayESs, sonetFarEndVTDayESAs, sonetFarEndVTDayESBs, sonetFarEndVTDaySESs, sonetFarEndVTDayUASs } STATUS current DESCRIPTION Expires January 1999 [Page 135] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 "The objects which are used to present the SONET Far End VT-path 1-day interval counters." ::= { sonetSupGroups 25 } sonetNotificationInformationGroup OBJECT-GROUP OBJECTS { sonetCounterId, sonetCounterValue } STATUS current DESCRIPTION "The notification information objects used by the threshold trap." ::= { sonetSupGroups 26 } sonetNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { sonetThresholdCrossing } STATUS current DESCRIPTION "The notification used to indicate threshold crossings." ::= { sonetSupGroups 27 } sonetSupCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The supplemental compliance statement for SONET interfaces. This assumes compliance with sonetCompliance2 in the SONET-MIB." MODULE -- this module GROUP sonetResetCountersGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetThresholdGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetDayThresholdGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetStartTimeGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetStartOfDayGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetSupMediumGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetMediumDayGroup DESCRIPTION "Implementation of the group is optional." Expires January 1999 [Page 136] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 GROUP sonetSupSectionGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetSectionDayGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetSupLineGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetLineDayGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetSupFarEndLineGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetFarEndLineDayGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetPathThresholdGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetPathDayThresholdGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetSupPathGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetPathDayGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetSupFarEndPathGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetFarEndPathDayGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetVTThresholdGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetVTDayThresholdGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetSupVTGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetVTDayGroup DESCRIPTION Expires January 1999 [Page 137] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 "Implementation of the group is optional." GROUP sonetSupFarEndVTGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetFarEndVTDayGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetNotificationInformationGroup DESCRIPTION "Implementation of the group is optional." GROUP sonetNotificationsGroup DESCRIPTION "Implementation of the group is optional." ::= { sonetSupCompliances 1 } END 6. Acknowledgments This document is not a product of an IETF Working Group. 7. References [1] Fowler, D., "Definitions of Managed Objects for the DS1, E1, DS2 and E2 Interface Types", , Newbridge Networks, Wed Feb 11 19:26:27 EST 1998. [2] Greene, M., "Definitions of Supplemental Managed Objects for the DS1, E1, DS2 and E2 Interface Types", , Ascom Nexion, May 31, 1996. [3] Fowler, D., "Definitions of Managed Objects for the DS3/E3 Interface Type", , Newbridge Networks, Tue Feb 24 09:53:17 EST 1998. [4] Gonda, R., "Definitions of Supplemental Managed Objects for the DS3/E3 Interface Type", , Cascade Communication Corporation, Thu Oct 17 14:05:52 EDT 1996. [5] Tesink, K., "Definitions of Managed Objects for the SONET/SDH Interface Type", , Bell Communications Research, August 26, 1996. Expires January 1999 [Page 138] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 [6] ANSI Standards Committee T1 - Telecommunications, "American National Standard for Telecommunications -- Digital Hierarchy -- Layer 1 In-Service Digital Transmission Performance Monitoring", ANSI T1.231-1997, October 20, 1997. [7] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure of Management Information for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC1902, SNMP Research,Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. [8] McCloghrie, K., and M. Rose, Editors, "Management Information Base for Network Management of TCP/IP-based internets: MIB-II", STD 17, RFC 1213, Hughes LAN Systems, Performance Systems International, March 1991. [9] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network Management Protocol", RFC 1157, SNMP Research, Performance Systems International, Performance Systems International, MIT Laboratory for Computer Science, May 1990. [10] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC1905, SNMP Research,Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. 8. Security Considerations Security issues are not discussed in this memo. 9. Author's Address Ken Chapman Argon Networks, Inc. 25 Porter Road Littleton, MA 01460 Phone: (978) 486-0665 x146 EMail: kchapman@argon.com Expires January 1999 [Page 139] INTERNET-DRAFT Supplemental SONET/SDH MIB July 1998 Table of Contents 1 Status of this Memo ............................................. 1 2 Abstract ........................................................ 1 3 The SNMP Network Management Framework ........................... 2 3.1 Object Definitions ............................................ 2 4 Overview ........................................................ 3 5 Definitions ..................................................... 3 6 Acknowledgments ................................................. 138 7 References ...................................................... 138 8 Security Considerations ......................................... 139 9 Author's Address ................................................ 139 Expires January 1999 [Page 140]