Network Working Group G. Li Internet-Draft Huawei Technologies Obsoletes: draft-jiang-asymmetric- S. Jiang ipv6-04 (if approved) Huawei Technologies Co., Ltd Intended status: Informational D. Eastlake 3rd Expires: August 24, 2021 Futurewei February 20, 2021 Native Short Addresses for the Internet Edge draft-li-native-short-addresses-00 Abstract This document describes a new approach to IP header compression including native short addresses adoption for use in scenarios where minimizing packet size is crucial but routing performance must be maximised. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on August 24, 2021. Copyright Notice Copyright (c) 2021 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of Li, et al. Expires August 24, 2021 [Page 1] Internet-Draft Native Short Addresses February 2021 the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 12. References . . . . . . . . . . . . . . . . . . . . . . . . . 7 Appendix A. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 8 1. The large address space of IPv6 is essential for the massive expansion of the network edge that will be caused by "Internet of Things" (IoT) technology over low-power or 5G links. However, the size of a raw IPv6 packet header causes difficulty due to the small maximum transmission units (MTU) allowed by typical low-power, low- cost link layers. For 5G, the importance of header overhead in small packets is discussed in [NGMN-5G]. Thus header compression, including address compression, is an important issue. This decreases the size of raw packets, but compressed IP addresses are not routeable except by decompressing them completely in every forwarding node. There are two issues here. The first is the extra computation resource needed for compressing or decompressing in constrained IoT nodes. The second is that full-length IPv6 routing will consume more memory to store routing tables and packet queues (assuming that routing is not bypassed by tunnelling). Such resource consumption is very undesirable in constrained nodes with limited storage, CPU power, and battery capacity. To mitigate these issues, here we propose a solution enabling the shortening of IPv6 addresses inside packets, and the routing of packets according to short addresses, without needing the overhead of a decompression step prior to route lookup. Considering that the scale and size of edge networks may vary widely, different lengths of short address can be used in different domains. Li, et al. Expires August 24, 2021 [Page 2] Internet-Draft Native Short Addresses February 2021 As an illustrative example, consider an edge network which is known to never require more than a few hundred nodes, which in most cases will communicate either with each other, or with application layer gateways to the rest of the Internet. Rather than needing 128-bit addresses, such a network could very well operate with 16-bit addresses. Also, it could very likely operate without needing enhancements such as differentiated services, ECN or flow labels. If only IPv6 is supported, the version number field is pointless. There is no reason for IPv6 packets within such a network to contain 40-byte headers as specified in [RFC8200]. Therefore, the useful information could be carried in 8 bytes (see Figure 1). Furthermore, routers within the edge network can route packets directly on 16-bit addresses, reducing RIB and FIB sizes and the lookup time. +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Payload Length | Next Header | Hop Limit | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Address | Destination Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 1 This work is distinct from previous work on address compression [RFC6282] [RFC7400]. Although those solutions tackle the problem of small MTU size, they do not address the problem of decompression overhead. This work is also distinct from the work on static context header compression [RFC8724], as discussed in more detail below. Finally, this work is distinct from the 6LoWPAN Routing Header [RFC8138], which can support truncated addresses in a different way. 2. The use of IPv6 naturally implies 128-bit addresses for both source and destination. However, this address size is huge by the standards of IoT edge networks. We propose the use of a context parameter to indicate the effective length of the IP address for every node in a local domain. If the effective length is N bits, then all addresses in the domain are assumed to be preceded by a common prefix of 128-N bits, when a full size IPv6 address is needed. Any node in the domain that needs the full address, such as a gateway node to the Internet, can therefore easily synthesize it. If a client communicates with a server that is in the local domain, short addresses will be used end-to-end. Li, et al. Expires August 24, 2021 [Page 3] Internet-Draft Native Short Addresses February 2021 The address length parameter may be needed by every node in the domain. It can be spread by various techniques: The solution operates by shortening IP address fields to save overhead. To enhance this, we propose a new field named Flexible Header Encoding (FHE). It consists of 8 bits, each indicating whether the corresponding IPv6 header field [RFC8200] exists. The "Version" field is a special case. In the context of FHE, all packets are presumed to be IPv6 so the normal version field has no purpose. The Modified Version field, if present, has the following encoded meanings: All fields, including the Modified Version field, follow the FHE in the same order as in [RFC8200], with no padding. There are no alignment requirements, but when a packet is decompressed to a normal IPv6 format, padding options as defined in RFC8200 must be inserted. Compared to the illustrative example in Figure 1, the actual packet size would therefore be 10 bytes, a considerable improvement on the standard 40 bytes. This method of shortening packets by using the FHE header is called Asymmetric IPv6. One implication of the above is that the source and destination addresses may be elided completely if they are implicit. Sourceless packets were originally suggested in [Crowcroft]. Figure 2 illustrates an example of the FHE format. In this example the traffic class, flow label and source address are elided, and the destination address is truncated to 16 bits. The modified version field could be 0b0001 or 0b0010. FHE octet Modified +-+-+-+-+-+-+-+-+ Version |1 0 0 1 1 1 0 1| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0 0 0 1| Payload Length | Next Header | Hop | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Limit | Truncated Destination Address | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | + Transport payload | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+......... Figure 2 Li, et al. Expires August 24, 2021 [Page 4] Internet-Draft Native Short Addresses February 2021 Note that Asymmetric IPv6 does not contain any special handling for IPv6 fragmentation, which will operate exactly as described in [RFC8200], with Asymmetric IPv6 applied to each fragment packet. However, we assume that in IoT deployment scenarios, packets whose length exceeds the IPv6 minimum link MTU before applying Asymmetric IPv6 will be rare. If the underlying link layer cannot carry complete packets even after applying Asymmetric IPv6 compression, an adaptation layer will be necessary exactly as for normal IPv6. 3. Truncated intra-domain addresses will be used to identify nodes inside the domain. When a packet is sent from an IoT node to an external IPv6 host , the node's intra-domain address, which is unique in the domain, will be carried in the source address field. When the packet is forwarded outside the domain by a gateway, the intra-domain address will be transformed to a complete IPv6 address. To achieve this, the gateway should will maintain a globally routeable prefix for all the nodes in the domain. When a packet with an intra-domain source address is received, the gateway extracts this address and concatenates it to the prefix to form a standard, globally unique IPv6 address. Vice versa, when IPv6 packets are received from the Internet, the prefix will be removed to recover the intra-domain short address. There are two options for handling the addresses of external hosts within the domain. One is to use their full IPv6 addresses via Modified Version codes 0b0000 and 0b0001. The other is effectively a specialized form of Network Address Translation. Here, the gateway will maintain a dynamic mapping table between synthetic intra-domain addresses and IPv6 addresses. As packets are received, the gateway performs the appropriate mapping. The transformation must be checksum-neutral for the transport layer, so the methods designed for NAT46 should be adapted [RFC6145]. It is an engineering choice whether this method is preferable to carrying full 128-bit addresses on the IOT side. Which type of resource is more expensive should be seriously considered to choose the appropriate ways, e.g. computing, memory, or transmiting in various resource-constrained IoT networks. 4. Routing mechanisms may readily be adapted to truncated address sizes. If there is routing with an FHE domain, we assume that the truncated address size will be split into a prefix and an interface identifier, but this will not be at the traditional /64 boundary. If routing between different length addresses is required, a suitably modified Li, et al. Expires August 24, 2021 [Page 5] Internet-Draft Native Short Addresses February 2021 Forwarding Information Base (FIB) structure is needed, as for any variable length addressing scheme. A truncated address needs to be virtually expanded to 128 bits at the router's inbound interface, although this may not be the physical implementation. A possible routing choice for IOT edge networks is RPL [RFC6550], although a more complete survey can be found in [Talwar]. 5. The simplest approach to address configuration is simply to run normal IPv6 procedures (SLAAC or DHCPv6), on the argument that this is a rare process and the overhead does not matter. If the truncated address size is less than 64 bits, it will be necessary to use shorter interface identifiers than normal, but this is not a major change. Once a node has acquired an IPv6 address and has learned the local address length parameter as outlined in Section 2, it can continue in FHE mode. 6. Although FHE nodes can only talk directly to each other, they are essentially a special form of IPv6 node and they can communicate with the whole IPv6 Internet via gateways. The complexity is not greater than 6LoWPAN. If appropriate, the 6LoWPAN adaptation layer [RFC4944] could be used, with a specific dispatch type. 7. Static Context Header Compression (SCHC) [RFC8724] is a powerful mechanism for reducing IPv6 packet size in an IoT application environment. In particular it includes a profile for UDP over IPv6, and a somewhat modified version of this profile could achieve much of what Asymmetric IPv6 proposes. In addition, SCHC provides support for fragmentation in the case of very small link MTUs. However, SCHC is by design static, and once a context is established the fields to be compressed do not change. Asymmetric IPv6 transmits the FHE and Modified Version bytes with every packet, so it provides dynamic choice as to which header elements are compressed or elided. In a context where the desirable compression is fixed, e.g. every address is the same length, the flow label is never used, etc., SCHC can used to the same effect as Asymmetric IPv6. However, if the behavior needs to be dynamic, the signaling power of the FHE and Modified Version bytes in Asymmetric IPv6 is needed. Further study is needed whether the advantages of the two mechanisms can be combined. Li, et al. Expires August 24, 2021 [Page 6] Internet-Draft Native Short Addresses February 2021 8. FHE is essentially only a non-cryptographic compression technique so it neither adds to nor reduces the intrinsic security of an IPv6 packet. The address length parameter is not a secret, since all nodes in the domain must know it. The mechanism for distributing this parameter must be no less secure than any other configuration mechanism in use. Address-based privacy issues must be considered in deciding on the address length. If the number of bits available for the interface identifier is significantly less than the 64 currently in use, address traceability and guessability will be affected. However, if the traffic with short addresses is confined to within the edge network, the privacy issue will be minimized. [RFC7721] and [RFC7217] should be consulted prior to deciding the address length. 9. This document makes no request of the IANA. NOTE IN DRAFT: If the solution of a 6LoWPAN dispatch type is adopted, a suitable assignment request will be added. 10. Brian Carpenter as one of the authors of draft-jiang-asymmetric-ipv6 directly contributes to the former draft's all sections, especially for polishing of introduction and solution's description. As his will, this draft absorbs most of the results and will go further regarding him as the most important contributor. 11. Useful comments were received from Uma Chunduri, Cheng Li, Pascal Thubert, Laurent Toutain and others. 12. References [Crowcroft] Crowcroft, J. and M. Bagnulo, "SNA: Sourceless Network Architecture", 2014. [NGMN-5G] Thibault, I., "5G Extreme Requirements: Operators' views on fundamental trade-offs", 2017. [Talwar] Talwar, M., "Routing Techniques and Protocols for Internet of Things: a Survey", 2015. Li, et al. Expires August 24, 2021 [Page 7] Internet-Draft Native Short Addresses February 2021 Appendix A. Authors' Addresses Guangpeng Li Huawei Technologies Q14, Huawei Campus No.156 Beiqing Road Hai-Dian District, Beijing 100095 P.R. China Email: liguangpeng@huawei.com Sheng Jiang Huawei Technologies Co., Ltd Q14, Huawei Campus, No.156 Beiqing Road Hai-Dian District, Beijing, 100095 P.R. China Email: jiangsheng@huawei.com Donald Eastlake 3rd Futurewei Technologies 2386 Panoramic Circle Apopka FL 32703 32703 United States of America Email: d3e3e3@gmail.com Li, et al. Expires August 24, 2021 [Page 8]