Network Working Group Luca Martini Internet Draft Cisco Systems, Inc. Expiration Date: August 2005 Nasser El-Aawar Level 3 Communications, LLC. Steve Vogelsang Daniel Tappan John Shirron Eric C. Rosen Toby Smith Alex Hamilton Laurel Networks, Inc. Jayakumar Jayakumar Cisco Systems, Inc. Vasile Radoaca Dimitri Stratton Vlachos Nortel Networks Mazu Networks, Inc. Andrew G. Malis Chris Liljenstolpe Vinai Sirkay Cable & Wireless Vivace Networks, Inc. Giles Heron Dave Cooper PacketExchange Ltd. Global Crossing Kireeti Kompella Juniper Networks February 2005 Transport of Layer 2 Frames Over MPLS draft-martini-l2circuit-trans-mpls-16.txt Status of this Memo By submitting this Internet-Draft, we certify that any applicable patent or other IPR claims of which we are aware have been disclosed, or will be disclosed, and any of which we become aware will be disclosed, in accordance with RFC 3668. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." Martini, et al. [Page 1] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 The list of current Internet-Drafts can be accessed at http://www.ietf.org/1id-abstracts.html The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Abstract This document describes methods for transporting the Protocol Data Units (PDUs) of layer 2 protocols such as Frame Relay, ATM AAL5, Ethernet, and providing a SONET circuit emulation service across an MPLS network. Martini, et al. [Page 2] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 Table of Contents 1 Specification of Requirements .......................... 3 2 Introduction ........................................... 4 3 Tunnel Labels and VC Labels ............................ 4 4 Protocol-Specific Details .............................. 6 4.1 Frame Relay ............................................ 6 4.2 ATM .................................................... 6 4.2.1 ATM AAL5 VCC Transport ................................. 6 4.2.2 ATM Transparent Cell Transport ......................... 6 4.2.3 ATM VCC and VPC Cell Transport ......................... 7 4.2.4 OAM Cell Support ....................................... 7 4.2.5 ILMI Support ........................................... 8 4.3 Ethernet VLAN .......................................... 8 4.4 Ethernet ............................................... 8 4.5 HDLC ................................................... 8 4.6 PPP .................................................... 9 5 LDP .................................................... 9 5.1 Interface Parameters Field ............................. 11 5.2 C Bit handling procedures .............................. 12 5.2.1 VC types for which the control word is REQUIRED ........ 12 5.2.2 VC types for which the control word is NOT mandatory ... 12 5.2.3 Status codes ........................................... 16 5.3 LDP label Withdrawal procedures ........................ 16 5.4 Sequencing Considerations .............................. 16 5.4.1 Label Mapping Advertisements ........................... 17 5.4.2 Label Mapping Release .................................. 17 6 IANA Considerations .................................... 17 7 Security Considerations ................................ 18 8 Full Copyright Statement ............................... 18 9 Intellectual Property Statement ........................ 18 10 References ............................................. 19 11 Author Information ..................................... 20 1. Specification of Requirements The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119. Martini, et al. [Page 3] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 2. Introduction In an MPLS network, it is possible to carry the Protocol Data Units (PDUs) of layer 2 protocols by prepending an MPLS label stack to these PDUs. This document specifies the necessary label distribution procedures for accomplishing this using the encapsulation methods in [7]. We restrict discussion to the case of point-to-point transport. QoS related issues are not discussed in this draft. This document describes methods for transporting a number of protocols; in some cases, transporting a particular protocol may have several modes of operation. Each of these protocols and/or modes may be implemented independently. An accompanying document [8] also describes a method for transporting time division multiplexed (TDM) digital signals (TDM circuit emulation) over a packet-oriented MPLS network. The transmission system for circuit-oriented TDM signals is the Synchronous Optical Network (SONET)[5]/Synchronous Digital Hierarchy (SDH) [6]. To support TDM traffic, which includes voice, data, and private leased line service, the MPLS network must emulate the circuit characteristics of SONET/SDH payloads. MPLS labels and a new circuit emulation header are used to encapsulate TDM signals and provide the Circuit Emulation Service over MPLS (CEM). 3. Tunnel Labels and VC Labels Suppose it is desired to transport layer 2 PDUs from ingress LSR R1 to egress LSR R2, across an intervening MPLS network. We assume that there is an LSP from R1 to R2. That is, we assume that R1 can cause a packet to be delivered to R2 by pushing some label onto the packet and sending the result to one of its adjacencies. Call this label the "tunnel label", and the corresponding LSP the "tunnel LSP". The tunnel LSP merely gets packets from R1 to R2, the corresponding label doesn't tell R2 what to do with the payload, and in fact if penultimate hop popping is used, R2 may never even see the corresponding label. (If R1 itself is the penultimate hop, a tunnel label may not even get pushed on.) Thus if the payload is not an IP packet, there must be a label, which becomes visible to R2, that tells R2 how to treat the received packet. Call this label the "VC label". So when R1 sends a layer 2 PDU to R2, it first pushes a VC label on its label stack, and then (if R1 is not adjacent to R2) pushes on a tunnel label. The tunnel label gets the MPLS packet from R1 to R2; the VC label is not visible until the MPLS packet reaches R2. R2's Martini, et al. [Page 4] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 disposition of the packet is based on the VC label. Note that the tunnel could be a GRE encapsulated MPLS tunnel between R1 and R2. In this case R1 would be adjacent to R2, and only the VC label would be used, and the intervening network need only carry IP packets. If the payload of the MPLS packet is, for example, an ATM AAL5 PDU, the VC label will generally correspond to a particular ATM VC at R2. That is, R2 needs to be able to infer from the VC label the outgoing interface and the VPI/VCI value for the AAL5 PDU. If the payload is a Frame Relay PDU, then R2 needs to be able to infer from the VC label the outgoing interface and the DLCI value. If the payload is an Ethernet frame, then R2 needs to be able to infer from the VC label the outgoing interface, and perhaps the VLAN identifier. This process is unidirectional, and will be repeated independently for bidirectional operation. It is REQUIRED to assign the same VC ID, and VC type for a given circuit in both directions. The group ID (see below) MUST NOT be required to match in both directions. The transported frame MAY be modified when it reaches the egress router. If the header of the transported layer 2 frame is modified, this MUST be done at the egress LSR only. Note that the VC label must always be at the bottom of the label stack, and the tunnel label, if present, must be immediately above the VC label. Of course, as the packet is transported across the MPLS network, additional labels may be pushed on (and then popped off) as needed. Even R1 itself may push on additional labels above the tunnel label. If R1 and R2 are directly adjacent LSRs, then it may not be necessary to use a tunnel label at all. This document does not specify a method for distributing the tunnel label or any other labels that may appear above the VC label on the stack. Any acceptable method of MPLS label distribution will do. This document does specify a method for assigning and distributing the VC label. Static label assignment MAY be used, and implementations SHOULD provide support for this. When signaling is used, the VC label MUST be distributed from R2 to R1 using LDP in the downstream unsolicited mode; this requires that an LDP session be created between R1 and R2. It should be noted that this LDP session is not necessarily transported along the same path as the Layer 2 PDUs. [1] In addition, when using LDP to distribute the VC label, liberal label retention mode SHOULD be used. However, as required in [1], the label request operation (mainly used by conservative label retention mode) MUST be implemented. VC labels MUST be allocated from the per-platform label space. Martini, et al. [Page 5] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 Note that this technique allows an unbounded number of layer 2 "VCs" to be carried together in a single "tunnel". Thus it scales quite well in the network backbone. While this document currently defines the emulation of Frame Relay and ATM PVC services, it specifically does not preclude future enhancements to support switched service (SVC and SPVC) emulation. 4. Protocol-Specific Details 4.1. Frame Relay The Frame Relay PDUs are encapsulated according to the procedures defined in [7]. The MPLS edge LSR MUST provide Frame Relay PVC status signaling to the Frame Relay network. If the MPLS edge LSR detects a service affecting condition as defined in [2] Q.933 Annex A.5 sited in IA FRF1.1, it MUST withdraw the label that corresponds to the frame relay DLCI. The Egress LSR SHOULD generate the corresponding errors and alarms as defined in [2] on the egress Frame relay VC. 4.2. ATM 4.2.1. ATM AAL5 VCC Transport ATM AAL5 CSPS-SDUs are encapsulated according to [7] ATM AAL5 CPCS- SDU mode. This mode allows the transport of ATM AAL5 CSPS-SDUs traveling on a particular ATM PVC across the MPLS network to another ATM PVC. 4.2.2. ATM Transparent Cell Transport This mode is similar to the Ethernet port mode. Every cell that is received at the ingress ATM port on the ingress LSR, R1, is encapsulated according to [7], ATM cell mode, and sent across the LSP to the egress LSR, R2. This mode allows an ATM port to be connected to only one other ATM port. [7] allows for grouping of multiple cells into a single MPLS frame. Grouping of ATM cells is OPTIONAL for transmission at the ingress LSR, R1. If the Egress LSR R2 supports cell concatenation the ingress LSR, R1, should only concatenate cells up to the "Maximum Number of concatenated ATM cells" parameter received as part of the FEC element. Martini, et al. [Page 6] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 4.2.3. ATM VCC and VPC Cell Transport This mode is similar to the ATM AAL5 VCC transport except that cells are transported. Every cell that is received on a pre-defined ATM PVC, or ATM PVP, at the ingress ATM port on the ingress LSR, R1, is encapsulated according to [7], ATM cell mode, and sent across the LSP to the egress LSR R2. Grouping of ATM cells is OPTIONAL for transmission at the ingress LSR, R1. If the Egress LSR R2 supports cell concatenation the ingress LSR, R1, MUST only concatenate cells up to the "Maximum Number of concatenated ATM cells in a frame" parameter received as part of the FEC element. 4.2.4. OAM Cell Support OAM cells MAY be transported on the VC LSP. When the LSR is operating in AAL5 CPCS-SDU transport mode if it does not support transport of ATM cells, the LSR MUST discard incoming MPLS frames on an ATM VC LSP that contain a VC label with the T bit set [7]. When operating in AAL5 SDU transport mode an LSR that supports transport of OAM cells using the T bit defined in [7], or an LSR operating in any of the three cell transport modes MUST follow the procedures outlined in [9] section 8 for mode 0 only, in addition to the applicable procedures specified in [6]. 4.2.4.1. OAM Cell Emulation Mode AN LSR that does not support transport of OAM cells across an LSP MAY provide OAM support on ATM PVCs using the following procedures: A pair of LSRs MAY emulate a bidrectional ATM VC by two uni- directional LSPs. If an F5 end-to-end OAM cell is received from a ATM VC, by either LSR that is transporting this ATM VC, with a loopback indication value of 1, and the LSR has a label mapping for the ATM VC, then the LSR MUST decrement the loopback indication value and loop back the cell on the ATM VC. Otherwise the loopback cell MUST be discarded by the LSR. The ingress LSR, R1, may also optionally be configured to periodically generate F5 end-to-end loopback OAM cells on a VC. If the LSR fails to receive a response to an F5 end-to-end loopback OAM cell for a pre-defined period of time it MUST withdraw the label mapping for the VC. If an ingress LSR, R1, receives an AIS F5 OAM cell, fails to receive a pre-defined number of the End-to-End loop OAM cells, or a physical interface goes down, it MUST withdraw the label mappings for all VCs Martini, et al. [Page 7] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 associated with the failure. When a VC label mapping is withdrawn, the egress LSR, R2, MUST generate AIS F5 OAM cells on the VC associated with the withdrawn label mapping. In this mode it is very useful to apply a unique group ID to each interface. In the case where a physical interface goes down, a wild card label withdraw can be sent to all LDP neighbors, greatly reducing the signaling response time. 4.2.5. ILMI Support An MPLS edge LSR MAY provide an ATM ILMI to the ATM edge switch. If an ingress LSR receives an ILMI message indicating that the ATM edge switch has deleted a VC, or if the physical interface goes down, it MUST withdraw the label mappings for all VCs associated with the failure. When a VC label mapping is withdrawn, the egress LSR SHOULD notify its client of this failure by deleting the VC using ILMI. 4.3. Ethernet VLAN The Ethernet frame will be encapsulated according to the procedures in [12]. It should be noted that if the VLAN identifier is modified by the egress LSR, according to the procedures outlined above, the Ethernet spanning tree protocol might fail to work properly. If the LSR detects a failure on the Ethernet physical port, or the port is administratively disabled, it MUST withdraw the label mappings for all VCs associated with the port. 4.4. Ethernet The Ethernet frame will be encapsulated according to the procedures in [12]. If the LSR detects a failure on the Ethernet physical port, or the port is administratively disabled, the corresponding VC label mapping MUST be withdrawn. 4.5. HDLC HDLC frames are encapsulated according to the procedures in [7]. If the MPLS edge LSR detects that the physical link has failed, or the port is adminstratively disabled, it MUST withdraw the label mapping that corresponds to the HDLC link. Martini, et al. [Page 8] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 4.6. PPP PPP frames are encapsulated according to the procedures in [7]. If the MPLS edge LSR detects that the physical link has failed, or the port is adminstratively disabled, it MUST withdraw the label mapping that corresponds to the PPP link. 5. LDP The VC label bindings are distributed using the LDP downstream unsolicited mode described in [1]. The LSRs will establish an LDP session using the Extended Discovery mechanism described in [1, section 2.4.2 and 2.5], for this purpose a new type of FEC element is defined. The FEC element type is 128. [note1] Only a single VC FEC element MUST be advertised per LDP VC label. The Virtual Circuit FEC element, is defined as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | VC tlv |C| VC Type |VC info Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Group ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | VC ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Interface parameters | | " | | " | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ - VC Type A 15 bit quantity containing a value which represents the type of VC. Assigned Values are: VC Type Description 0x0001 Frame Relay DLCI 0x0002 ATM AAL5 VCC transport 0x0003 ATM transparent cell transport 0x0004 Ethernet VLAN 0x0005 Ethernet 0x0006 HDLC 0x0007 PPP 0x8008 CEM [8] Martini, et al. [Page 9] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 0x0009 ATM VCC cell transport 0x000A ATM VPC cell transport - Control word bit (C) The highest order bit (C) of the VC type is used to flag the presence of a control word ( defined in [7] ) as follows: bit 15 = 1 control word present on this VC. bit 15 = 0 no control word present on this VC. Please see the section "C Bit handling procedures" for further explenation. - VC information length Length of the VC ID field and the interface parameters field in octets. If this value is 0, then it references all VCs using the specified group ID and there is no VC ID present, nor any interface parameters. - Group ID An arbitrary 32 bit value which represents a group of VCs that is used to create groups in the VC space. The group ID is intended to be used as a port index, or a virtual tunnel index. To simplify configuration a particular VC ID at ingress could be part of the virtual tunnel for transport to the egress router. The Group ID is very useful to send wild card label withdrawals to remote LSRs upon physical port failure. - VC ID A non zero 32-bit connection ID that together with the VC type, identifies a particular VC. - Interface parameters This variable length field is used to provide interface specific parameters, such as interface MTU. Martini, et al. [Page 10] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 5.1. Interface Parameters Field This field specifies interface specific parameters. When aplicable, it MUST be used to validate that the LSRs, and the ingress and egress ports at the edges of the circuit, have the necessary capabilities to interoperate with each other. The field structure is defined as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Parameter ID | Length | Variable Length Value | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Variable Length Value | | " | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The parameter ID is defined as follows: Parameter ID Length Description 0x01 4 Interface MTU in octets. 0x02 4 Maximum Number of concatenated ATM cells. 0x03 up to 82 Optional Interface Description string. 0x04 4 CEM [8] Payload Bytes. 0x05 4 CEM options. The Length field is defined as the length of the interface parameter including the parameter id and length field itself. Processing of the interface parameters should continue when encounting unknown interface parameters and they MUST be silently ignored. - Interface MTU A 2 octet value indicating the MTU in octets. This is the Maximum Transmission Unit, excluding encapsulation overhead, of the egress packet interface that will be transmitting the decapsulated PDU that is received from the MPLS network. This parameter is applicable only to VC types 1, 2, 4, 5, 6, and 7, and is REQUIRED for these VC types. If this parameter does not match in both directions of a specific VC, that VC MUST NOT be enabled. - Maximum Number of concatenated ATM cells A 2 octet value specifying the maximum number of concatenated ATM cells that can be processed as a single PDU by the egress LSR. An ingress LSR transmitting concatenated cells on this VC can Martini, et al. [Page 11] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 concatenate a number of cells up to the value of this parameter, but MUST NOT exceed it. This parameter is applicable only to VC types 3, 9, and 0x0a, and is REQUIRED for these VC types. This parameter does not need to match in both directions of a specific VC. - Optional Interface Description string This arbitrary, OPTIONAL, interface description string can be used to send an administrative description text string to the remote LSR. This parameter is OPTIONAL, and is applicable to all VC types. The interface description parameter string length is variable, and can be from 0 to 80 octets. - Payload Bytes A 2 octet value indicating the the number of TDM payload octets contained in all packets on the CEM stream, from 48 to 1,023 octets. All of the packets in a given CEM stream have the same number of payload bytes. Note that there is a possibility that the packet size may exceed the SPE size in the case of an STS-1 SPE, which could cause two pointers to be needed in the CEM header, since the payload may contain two J1 bytes for consecutive SPEs. For this reason, the number of payload bytes must be less than or equal to 783 for STS-1 SPEs. - CEM Options. An optional 16 Bit value of CEM Flags. See [8] for the definition of the bit values. 5.2. C Bit handling procedures 5.2.1. VC types for which the control word is REQUIRED The Label Mapping messages which are sent in order to set up these VCs MUST have c=1. When a Label Mapping message for a VC of one of these types is received, and c=0, a Label Release MUST be sent, with an "Illegal C-bit" status code. In this case, the VC will not come up. 5.2.2. VC types for which the control word is NOT mandatory If a system is capable of sending and receiving the control word on VC types for which the control word is not mandatory, then each such VC endpoint MUST be configurable with a parameter that specifies whether the use of the control word is PREFERRED or NOT PREFERRED. Martini, et al. [Page 12] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 For each VC, there MUST be a default value of this parameter. This specification does NOT state what the default value should. If a system is NOT capable of sending and receiving the control word on VC types for which the control word is not mandatory, then it behaves as exactly as if it were configured for the use of the control word to be NOT PREFERRED. If a Label Mapping message for the VC has already been received, but no Label Mapping message for the VC has yet been sent, then the procedure is the following: -i. If the received Label Mapping message has c=0, send a Label Mapping message with c=0, and the control word is not used. -ii. If the received Label Mapping message has c=1, and the VC is locally configured such that the use of the control word is preferred, then send a Label Mapping message with c=1, and the control word is used. -iii. If the received Label Mapping message has c=1, and the VC is locally configured such that the use of the control word is not preferred or the control word is not supported, then act as if no Label Mapping message for the VC had been received (i.e., proceed to the next paragraph). If a Label Mapping message for the VC has not already been received (or if the received Label Mapping message had c=1 and either local configuration says that the use of the control word is not preferred or the control word is not supported), then send a Label Mapping message in which the c bit is set to correspond to the locally configured preference for use of the control word. (I.e., set c=1 if locally configured to prefer the control word, set c=0 if locally configured to prefer not to use the control word or if the control word is not supported). The next action depends on what control message is next received for that VC. The possibilities are: -i. A Label Mapping message with the same c bit value as specified in the Label Mapping message that was sent. VC setup is now complete, and the control word is used if c=1 but not used if c=0. -ii. A Label Mapping message with c=1, but the Label Mapping message that was sent has c=0. In this case, ignore the received Label Mapping message, and continue to wait for the next control message for the VC. -iii. A Label Mapping message with c=0, but the Label Mapping message that was sent has c=1. In this case, send a Label Withdraw message with a "Wrong c-bit" status code, followed by a Label Mapping message that has c=0. VC setup is now complete, and the control word is not used. Martini, et al. [Page 13] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 -iv. A Label Withdraw message with the "Wrong c-bit" status code. Treat as a normal Label Withdraw, but do not respond. Continue to wait for the next control message for the VC. If at any time after a Label Mapping message has been received, a corresponding Label Withdraw or Release is received, the action taken is the same as for any Label Withdraw or Release that might be received at any time. If both endpoints prefer the use of the control word, this procedure will cause it to be used. If either endpoint prefers not to use the control word, or does not support the control word, this procedure will cause it not to be used. If one endpoint prefers to use the control word but the other does not, the one that prefers not to use it is has no extra protocol to execute, it just waits for a Label Mapping message that has c=0. The following diagram illustrate the above procedures: Martini, et al. [Page 14] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 ------------------ Y | Received Label | N -------| Mapping Msg? |-------------- | ------------------ | | | -------------- | | | | | | | ------- ------- | | C=0 | | C=1 | | ------- ------- | | | | | | | | ---------------- | | | Control Word | N | | | Capable? |----------- | | ---------------- | | | Y | | | | | | | | ---------------- | | | | Control Word | N | | | | Preferred? |---- | | | ---------------- | | | | Y | | | | | | | | ---------------- | | | | | Control Word | | | | | | Preferred? | | | | | ---------------- | | | | N | Y | | | | | | | Send Send Send Send Send Send C=0 C=1 C=0 C=0 C=0 C=1 | | | | | | | | ---------------------------------- | If receive the same as sent, | | VC setup is complete. If not: | ---------------------------------- | | | | | | | | ------------------- ----------- | Receive | | Receive | | C=1 | | C=0 | ------------------- ----------- | | | | Wait for the Send next message Wrong C-Bit Martini, et al. [Page 15] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 | | Send Label Mapping Message with C=0 5.2.3. Status codes RFC 3036 has a range of Status Code values which are assigned by IANA on a First Come, First Served basis. These are in the range 0x20000000-0x3effffff [note 2]. The following new status codes are defined: 0x20000001 "Illegal C-Bit" 0x20000002 "Wrong C-Bit" 5.3. LDP label Withdrawal procedures As mentioned above the Group ID field can be used to withdraw all VC labels associated with a particular group ID. This procedure is OPTIONAL, and if it is implemented the LDP label withdraw message should be as follows: the VC information length field is set to 0, the VC ID field is not present, and the interface paramenters field is not present. For the purpose of this document this is called the "wild card withdraw procedure", and all LSRs implementing this design are REQUIRED to accept such a withdraw message, but are not required to send it. The interface parameters field MUST NOT be present in any LDP VC label withdrawal message or release message. A wildcard release message MUST include only the group ID.A Label Release message initiated from the imposition router must always include the VC ID. 5.4. Sequencing Considerations In the case where the router considers the sequence number field in the control word, it is important to note the following when advertising labels Martini, et al. [Page 16] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 5.4.1. Label Mapping Advertisements After a label has been withdrawn by the disposition router and/or released by the imposition router, care must be taken to not re- advertise (re-use) the released label until the disposition router can be reasonably certain that old packets containing the released label no longer persist in the MPLS network. This precaution is required to prevent the imposition router from restarting packet forwarding with sequence number of 1 when it receives the same label mapping if there are still older packets persisting in the network with sequence number between 1 and 32768. For example, if there is a packet with sequence number=n where n is in the interval[1,32768] travelling through the network, it would be possible for the disposition router to receive that packet after it re-advertises the label. Since the label has been released by the imposition router, the disposition router SHOULD be expecting the next packet to arrive with sequence number to be 1. Receipt of a packet with sequence number equal to n will result in n packets potentially being rejected by the disposition router until the imposition router imposes a sequence number of n+1 into a packet. Possible methods to avoid this is for the disposition router to always advertise a different VC label, or for the disposition router to wait for a sufficient time before attempting to re-advertised a recently released label. This is only an issue when sequence number processing at the disposition router is enabled. 5.4.2. Label Mapping Release In situations where the imposition router wants to restart forwarding of packets with sequence number 1, the router shall 1) Send to disposition router a label mapping release, and 2) Send to disposition router a label mapping request. When sequencing is supported, advertisement of a vc label in response to a label mapping request MUST also consider the issues discussed in 5.3.1 6. IANA Considerations As specified in this document, a Virtual Circuit FEC element contains the VC Type field. VC Type value 0 is reserved. VC Type values 1 through 10 are defined in this document. VC Type values 11 through 63 are to be assigned by IANA using the "IETF Consensus" policy defined in RFC2434. VC Type values 64 through 127 are to be assigned by IANA, using the "First Come First Served" policy defined in RFC2434. VC Type values 128 through 32767 are vendor-specific, and values in this range are not to be assigned by IANA. Martini, et al. [Page 17] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 As specified in this document, a Virtual Circuit FEC element contains the Interface Parameters field, which is a list of one or more parameters, and each parameter is identified by the Parameter ID field. Parameter ID value 0 is reserved. Parameter ID values 1 through 5 are defined in this document. Parameter ID values 6 through 63 are to be assigned by IANA using the "IETF Consensus" policy defined in RFC2434. Parameter ID values 64 through 127 are to be assigned by IANA, using the "First Come First Served" policy defined in RFC2434. Parameter ID values 128 through 255 are vendor- specific, and values in this range are not to be assigned by IANA. 7. Security Considerations This document does not affect the underlying security issues of MPLS. 8. Full Copyright Statement Copyright (C) The Internet Society (2004). This document is subject to the rights, licenses and restrictions contained in BCP 78 and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 9. Intellectual Property Statement The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at Martini, et al. [Page 18] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf- ipr@ietf.org. By submitting this Internet-Draft, I certify that any applicable patent or other IPR claims of which I am aware have been disclosed, or will be disclosed, and any of which I become aware will be disclosed, in accordance with RFC 3668. 10. References [1] "LDP Specification." L. Andersson, P. Doolan, N. Feldman, A. Fredette, B. Thomas. January 2001. RFC3036 [2] ITU-T Recommendation Q.933, and Q.922 Specification for Frame Mode Basic call control, ITU Geneva 1995 [3] "MPLS Label Stack Encoding", E. Rosen, Y. Rekhter, D. Tappan, G. Fedorkow, D. Farinacci, T. Li, A. Conta. RFC3032 [4] "IEEE 802.3ac-1998" IEEE standard specification. [5] American National Standards Institute, "Synchronous Optical Network Formats," ANSI T1.105-1995. [6] ITU Recommendation G.707, "Network Node Interface For The Synchronous Digital Hierarchy", 1996. [7] "Encapsulation Methods for Transport of Layer 2 Frames Over MPLS", draft-martini-l2circuit-encap-mpls-06.txt ( Work in progress ) [8] "SONET/SDH Circuit Emulation Service Over MPLS (CEM) Encapsulation", draft-malis-sonet-ces-mpls-05.txt ( Work in progress ) [9] "Frame Based ATM over SONET/SDH Transport (FAST)," 2000. [note1] FEC element type 128 is pending IANA approval. [note2] Status codes assigment is pending IANA approval. Martini, et al. [Page 19] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 11. Author Information Luca Martini Cisco Systems, Inc. 9155 East Nichols Avenue, Suite 400 Englewood, CO, 80112 e-mail: lmartini@cisco.com Nasser El-Aawar Level 3 Communications, LLC. 1025 Eldorado Blvd. Broomfield, CO, 80021 e-mail: nna@level3.net Giles Heron Tellabs Abbey Place 24-28 Easton Street High Wycombe Bucks HP11 1NT UK e-mail: giles.heron@tellabs.com Dimitri Stratton Vlachos Mazu Networks, Inc. 125 Cambridgepark Drive Cambridge, MA 02140 e-mail: d@mazunetworks.com Dan Tappan Cisco Systems, Inc. 250 Apollo Drive Chelmsford, MA, 01824 e-mail: tappan@cisco.com Jayakumar Jayakumar, Cisco Systems Inc. 225, E.Tasman, MS-SJ3/3, San Jose, CA, 95134 e-mail: jjayakum@cisco.com Martini, et al. [Page 20] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 Alex Hamilton, Cisco Systems Inc. 285 W. Tasman, MS-SJCI/3/4, San Jose, CA, 95134 e-mail: tahamilt@cisco.com Eric Rosen Cisco Systems, Inc. 250 Apollo Drive Chelmsford, MA, 01824 e-mail: erosen@cisco.com Steve Vogelsang Laurel Networks, Inc. Omega Corporate Center 1300 Omega Drive Pittsburgh, PA 15205 e-mail: sjv@laurelnetworks.com John Shirron Omega Corporate Center 1300 Omega Drive Pittsburgh, PA 15205 Laurel Networks, Inc. e-mail: jshirron@laurelnetworks.com Toby Smith Omega Corporate Center 1300 Omega Drive Pittsburgh, PA 15205 Laurel Networks, Inc. e-mail: tob@laurelnetworks.com Andrew G. Malis Tellabs 90 Rio Robles Dr. San Jose, CA 95134 e-mail: Andy.Malis@tellabs.com Martini, et al. [Page 21] Internet Draft draft-martini-l2circuit-trans-mpls-16.txt February 2005 Vinai Sirkay Vivace Networks, Inc. 2730 Orchard Parkway San Jose, CA 95134 e-mail: sirkay@technologist.com Vasile Radoaca Nortel Networks 600 Technology Park Billerica MA 01821 e-mail: vasile@nortelnetworks.com Chris Liljenstolpe Cable & Wireless 11700 Plaza America Drive Reston, VA 20190 e-mail: chris@cw.net Dave Cooper Global Crossing 960 Hamlin Court Sunnyvale, CA 94089 e-mail: dcooper@gblx.net Kireeti Kompella Juniper Networks 1194 N. Mathilda Ave Sunnyvale, CA 94089 e-mail: kireeti@juniper.net Martini, et al. [Page 22]