Network Working Group G. Mirsky Internet-Draft X. Min Intended status: Standards Track ZTE Corp. Expires: October 15, 2017 A. Pan W. Luo Ericsson April 13, 2017 Two-Way Active Measurement Protocol (TWAMP) Light Data Model draft-mirsky-ippm-twamp-light-yang-08 Abstract This document specifies the data model for implementations of Session-Sender and Session-Reflector for Two-Way Active Measurement Protocol (TWAMP) Light mode using YANG. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on October 15, 2017. Copyright Notice Copyright (c) 2017 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of Mirsky, et al. Expires October 15, 2017 [Page 1] Internet-Draft TWAMP Light data model April 2017 the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1. Conventions used in this document . . . . . . . . . . . . 2 1.1.1. Requirements Language . . . . . . . . . . . . . . . . 2 2. Scope, Model, and Applicability . . . . . . . . . . . . . . . 3 2.1. Data Model Parameters . . . . . . . . . . . . . . . . . . 3 2.1.1. Session-Sender . . . . . . . . . . . . . . . . . . . 3 2.1.2. Session-Reflector . . . . . . . . . . . . . . . . . . 4 3. Data Model . . . . . . . . . . . . . . . . . . . . . . . . . 4 3.1. Tree Diagram . . . . . . . . . . . . . . . . . . . . . . 5 3.2. YANG Module . . . . . . . . . . . . . . . . . . . . . . . 8 4. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 24 5. Security Considerations . . . . . . . . . . . . . . . . . . . 24 6. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 24 7. References . . . . . . . . . . . . . . . . . . . . . . . . . 24 7.1. Normative References . . . . . . . . . . . . . . . . . . 24 7.2. Informative References . . . . . . . . . . . . . . . . . 25 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 26 1. Introduction The Two-Way Active Measurement Protocol (TWAMP) [RFC5357] can be used to measure performance parameters of IP networks such as latency, jitter, and packet loss by sending test packets and monitoring their experience in the network. The [RFC5357] defines two protocols, TWAMP Control and TWAMP Test, and a profile of TWAMP Test, TWAMP Light. The TWAMP Light is known to have many implementations though no common management framework being defined, thus leaving some aspects of test packet processing to interpretation. The goal of this document is to collect analyze these variations; describe common model while allowing for extensions in the future. This document defines such a TWAMP data model and specifies it formally using the YANG data modeling language [RFC6020]. 1.1. Conventions used in this document 1.1.1. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. Mirsky, et al. Expires October 15, 2017 [Page 2] Internet-Draft TWAMP Light data model April 2017 2. Scope, Model, and Applicability The scope of this document includes model of the TWAMP Light as defined in Appendix I of [RFC5357]. This mode of TWAMP Light will be referred in this document as Stateless. Another mode, where the Session-Reflector is aware of the state of the TWAMP test session and thus can independently count reflected test packets, referred as Stateful. This document benefits from earlier attempt to define TWAMP MIB in [I-D.elteto-ippm-twamp-mib] and from TWAMP YANG model defined in [I-D.ietf-ippm-twamp-yang]. Figure 1 updates TWAMP-Light reference model presented in Appendix I [RFC5357] for the scenario when instantiation of a TWAMP-Test session between Session-Sender and Session-Reflector controlled by communication between a Configuration Client as a manager and Configuration Servers as agents of the configuration session. o----------------------------------------------------------o | Config client | o----------------------------------------------------------o || || || NETCONF/RESTCONF || || || o-------------------o o-------------------o | Config server | | Config server | | | | | +-------------------+ +-------------------+ | Session-Sender | <--- TWAMP-Test ---> | Session-Reflector | +-------------------+ +-------------------+ Figure 1: TWAMP Light Reference Model 2.1. Data Model Parameters This section describes all the parameters of the the TWAMP-Light data model. 2.1.1. Session-Sender The twamp-light-session-sender container holds items that are related to the configuration of the TWAMP-Light Session-Sender logical entity. The twamp-light-session-sender-state container holds information about the state of the particular TWAMP-Light test session. Mirsky, et al. Expires October 15, 2017 [Page 3] Internet-Draft TWAMP Light data model April 2017 RPCs twamp-sender-start and twamp-sender-stop respectively start and stop the referenced by session-id TWAMP-Light test session. 2.1.1.1. Controls for Test Session and Preformance Metric Calculation The data model supports several scenarios for Session-Sender to excute test sessions and calculate performance metrics: The test mode in which the test packets are sent unbound in time at defined by the parameter 'interval' in the twamp-light-session- sender container frquency is referred as continuous mode. Perfomance metrics in the continuous mode are calculated at period defined by the parameter 'measurement-interval'. The test mode that has specific number of the test packets configured for the test session in the 'number-of-packets' parameter is referred as periodic mode. The test session may be repeated by the Session-Sender with the same parameters. The 'repeat' parameter defines number of tests and the 'repeat- interval' - the interval between the consequitive tests. The perfomance metrics are calculated after each test session when the interval defined by the 'session-timeout' expires. 2.1.2. Session-Reflector The twamp-light-session-reflector container holds items that are related to the configuration of the TWAMP-Light Session-Reflector logical entity. The twamp-light-session-reflector-state container holds Session- Reflector state data for the particular TWAMP-Light test session. 3. Data Model Creating TWAMP-Light data model presents number of challenges and among them is identification of a test-session at Session-Reflector. A Session-Reflector MAY require only as little as its IP and UDP port number in received TWAMP-Test packet to spawn new test session. More so, to test processing of Class-of-Service along the same route in Equal Cost Multi-Path environment Session-Sender may run TWAMP test sessions concurrently using the same source IP address, source UDP port number, destination IP address, and destination UDP port number. Thus the only parameter that can be used to differentiate these test sessions would be DSCP value. The DSCP field may get re-marked along the path and without use of [RFC7750] that will go undetected, but by using five-tuple instead of four-tuple as a key we can ensure that TWAMP test packets that are considered as different test sessions follow the same path even in ECMP environments. Mirsky, et al. Expires October 15, 2017 [Page 4] Internet-Draft TWAMP Light data model April 2017 3.1. Tree Diagram module: ietf-twamp-light +--rw twamp-light | +--rw twamp-light-session-sender {session-sender-light}? | | +--rw sender-light-enable? enable | | +--rw test-session* [session-id] | | +--rw session-id uint32 | | +--rw test-session-enable? enable | | +--rw number-of-packets? union | | +--rw packet-padding-size? uint32 | | +--rw interval? uint32 | | +--rw session-timeout? uint32 | | +--rw measurement-interval? uint32 | | +--rw repeat? union | | +--rw repeat-interval? uint32 | | +--rw dscp-value? inet:dscp | | +--rw test-session-relector-mode? session-reflector-mode | | +--rw sender-ip inet:ip-address | | +--rw sender-udp-port inet:port-number | | +--rw reflector-ip inet:ip-address | | +--rw reflector-udp-port inet:port-number | | +--rw authentication-params! {twamp-light-authentication}? | | +--rw key-chain? kc:key-chain-ref | +--rw twamp-light-session-reflector {session-reflector-light}? | +--rw reflector-light-enable? enable | +--rw ref-wait? uint32 | +--rw reflector-light-mode-state? session-reflector-mode | +--rw test-session* [session-id] | +--rw session-id uint32 | +--rw dscp-handling-mode? session-dscp-mode | +--rw dscp-value? inet:dscp | +--rw sender-ip inet:ip-address | +--rw sender-udp-port inet:port-number | +--rw reflector-ip inet:ip-address | +--rw reflector-udp-port inet:port-number | +--rw authentication-params! {twamp-light-authentication}? | +--rw key-chain? kc:key-chain-ref +--ro twamp-light-state +--ro twamp-light-session-sender-state {session-sender-light}? | +--ro test-session-state* [session-id] | +--ro session-id uint32 | +--ro sender-session-state? enumeration | +--ro current-stats | | +--ro start-time yang:date-and-time | | +--ro number-of-packets? uint32 Mirsky, et al. Expires October 15, 2017 [Page 5] Internet-Draft TWAMP Light data model April 2017 | | +--ro packet-padding-size? uint32 | | +--ro interval? uint32 | | +--ro duplicate-packets? uint32 | | +--ro reordered-packets? uint32 | | +--ro sender-ip inet:ip-address | | +--ro sender-udp-port inet:port-number | | +--ro reflector-ip inet:ip-address | | +--ro reflector-udp-port inet:port-number | | +--ro dscp? inet:dscp | | +--ro sent-packets? uint32 | | +--ro rcv-packets? uint32 | | +--ro sent-packets-error? uint32 | | +--ro rcv-packets-error? uint32 | | +--ro last-sent-seq? uint32 | | +--ro last-rcv-seq? uint32 | | +--ro two-way-delay | | | +--ro delay | | | | +--ro min? yang:gauge32 | | | | +--ro max? yang:gauge32 | | | | +--ro avg? yang:gauge32 | | | +--ro delay-variation | | | +--ro min? uint32 | | | +--ro max? uint32 | | | +--ro avg? uint32 | | +--ro one-way-delay-far-end | | | +--ro delay | | | | +--ro min? yang:gauge32 | | | | +--ro max? yang:gauge32 | | | | +--ro avg? yang:gauge32 | | | +--ro delay-variation | | | +--ro min? uint32 | | | +--ro max? uint32 | | | +--ro avg? uint32 | | +--ro one-way-delay-near-end | | | +--ro delay | | | | +--ro min? yang:gauge32 | | | | +--ro max? yang:gauge32 | | | | +--ro avg? yang:gauge32 | | | +--ro delay-variation | | | +--ro min? uint32 | | | +--ro max? uint32 | | | +--ro avg? uint32 | | +--ro two-way-loss | | | +--ro loss-count? int32 | | | +--ro loss-ratio? percentage | | +--ro one-way-loss-far-end | | | +--ro loss-count? int32 | | | +--ro loss-ratio? percentage Mirsky, et al. Expires October 15, 2017 [Page 6] Internet-Draft TWAMP Light data model April 2017 | | +--ro one-way-loss-near-end | | +--ro loss-count? int32 | | +--ro loss-ratio? percentage | +--ro history-stats* [id] | +--ro id uint32 | +--ro end-time yang:date-and-time | +--ro number-of-packets? uint32 | +--ro packet-padding-size? uint32 | +--ro interval? uint32 | +--ro duplicate-packets? uint32 | +--ro reordered-packets? uint32 | +--ro loss-packets? uint32 | +--ro sender-ip inet:ip-address | +--ro sender-udp-port inet:port-number | +--ro reflector-ip inet:ip-address | +--ro reflector-udp-port inet:port-number | +--ro dscp? inet:dscp | +--ro sent-packets? uint32 | +--ro rcv-packets? uint32 | +--ro sent-packets-error? uint32 | +--ro rcv-packets-error? uint32 | +--ro last-sent-seq? uint32 | +--ro last-rcv-seq? uint32 | +--ro two-way-delay | | +--ro delay | | | +--ro min? yang:gauge32 | | | +--ro max? yang:gauge32 | | | +--ro avg? yang:gauge32 | | +--ro delay-variation | | +--ro min? uint32 | | +--ro max? uint32 | | +--ro avg? uint32 | +--ro one-way-delay-far-end | | +--ro delay | | | +--ro min? yang:gauge32 | | | +--ro max? yang:gauge32 | | | +--ro avg? yang:gauge32 | | +--ro delay-variation | | +--ro min? uint32 | | +--ro max? uint32 | | +--ro avg? uint32 | +--ro one-way-delay-near-end | +--ro delay | | +--ro min? yang:gauge32 | | +--ro max? yang:gauge32 | | +--ro avg? yang:gauge32 | +--ro delay-variation | +--ro min? uint32 Mirsky, et al. Expires October 15, 2017 [Page 7] Internet-Draft TWAMP Light data model April 2017 | +--ro max? uint32 | +--ro avg? uint32 +--ro twamp-light-session-reflector-state \ | {session-reflector-light}? +--ro reflector-light-admin-status boolean +--ro test-session-state* [session-id] +--ro session-id uint32 +--ro sent-packets? uint32 +--ro rcv-packets? uint32 +--ro sent-packets-error? uint32 +--ro rcv-packets-error? uint32 +--ro last-sent-seq? uint32 +--ro last-rcv-seq? uint32 +--ro sender-ip inet:ip-address +--ro sender-udp-port inet:port-number +--ro reflector-ip inet:ip-address +--ro reflector-udp-port inet:port-number rpcs: +---x twamp-sender-start | +---w input | +---w session-id uint32 +---x twamp-sender-stop +---w input +---w session-id uint32 3.2. YANG Module file "ietf-twamp-light@2017-04-13.yang" module ietf-twamp-light { namespace "urn:ietf:params:xml:ns:yang:ietf-twamp-light"; //namespace need to be assigned by IANA prefix "ietf-twamp-light"; import ietf-inet-types { prefix inet; } import ietf-yang-types { prefix yang; } import ietf-key-chain { prefix kc; } organization "IETF IPPM (IP Performance Metrics) Working Group"; Mirsky, et al. Expires October 15, 2017 [Page 8] Internet-Draft TWAMP Light data model April 2017 contact "draft-mirsky-ippm-twamp-light-yang@tools.ietf.org"; description "TWAMP Light Data Model"; revision "2017-04-13" { description "08 version. Appendix I RFC 5357 is covered."; reference "RFC 5357"; } feature session-sender-light { description "This feature relates to the device functions as the TWAMP Light Session-Sender"; } feature session-reflector-light { description "This feature relates to the device functions as the TWAMP Light Session-Reflector"; } feature twamp-light-authentication { description "TWAMP Light authentication supported"; } typedef enable { type boolean; description "enable"; } typedef session-reflector-mode { type enumeration { enum stateful { description "When the Session-Reflector is stateful, i.e. is aware of TWAMP-Test session state."; } enum stateless { description "When the Session-Reflector is stateless, i.e. is not aware of the state of TWAMP-Test session."; } } description "State of the Session-Reflector"; Mirsky, et al. Expires October 15, 2017 [Page 9] Internet-Draft TWAMP Light data model April 2017 } typedef session-dscp-mode { type enumeration { enum copy-received-value { description "Use DSCP value copied from received TWAMP test packet of the test session."; } enum use-configured-value { description "Use DSCP value configured for this test session on the Session-Reflector."; } } description "DSCP handling mode by Session-Reflector."; } typedef percentage { type decimal64 { fraction-digits 5; } description "Percentage"; } grouping maintenance-statistics { description "Maintenance statistics grouping"; leaf sent-packets { type uint32; description "Packets sent"; } leaf rcv-packets { type uint32; description "Packets received"; } leaf sent-packets-error { type uint32; description "Packets sent error"; } leaf rcv-packets-error { type uint32; description "Packets received error"; } leaf last-sent-seq { type uint32; description "Last sent sequence number"; } Mirsky, et al. Expires October 15, 2017 [Page 10] Internet-Draft TWAMP Light data model April 2017 leaf last-rcv-seq { type uint32; description "Last received sequence number"; } } grouping delay-statistics { description "Delay statistics grouping"; container delay { description "Packets transmitted delay"; leaf min { type yang:gauge32; units microseconds; description "Min of Packets transmitted delay"; } leaf max { type yang:gauge32; units microseconds; description "Max of Packets transmitted delay"; } leaf avg { type yang:gauge32; units microseconds; description "Avg of Packets transmitted delay"; } } container delay-variation { description "Packets transmitted delay variation"; leaf min { type uint32; units microseconds; description "Min of Packets transmitted delay variation"; } leaf max { type uint32; units microseconds; description "Max of Packets transmitted delay variation"; } leaf avg { Mirsky, et al. Expires October 15, 2017 [Page 11] Internet-Draft TWAMP Light data model April 2017 type uint32; units microseconds; description "Avg of Packets transmitted delay variation"; } } } grouping packet-loss-statistics { description "Grouping for Packet Loss statistics"; leaf loss-count { type int32; description "Number of lost packets."; } leaf loss-ratio { type percentage; description "Ratio of packets lost to packets sent."; } } grouping session-light-parameters { description "Parameters common among Session-Sender and Session-Reflector"; leaf sender-ip { type inet:ip-address; mandatory true; description "Sender IP address"; } leaf sender-udp-port { type inet:port-number { range "49152..65535"; } mandatory true; description "Sender UDP port number"; } leaf reflector-ip { type inet:ip-address; mandatory true; description "Reflector IP address"; } leaf reflector-udp-port { type inet:port-number{ range "49152..65535"; Mirsky, et al. Expires October 15, 2017 [Page 12] Internet-Draft TWAMP Light data model April 2017 } mandatory true; description "Reflector UDP port number"; } } grouping session-light-auth-params { description "Grouping for TWAMP Light authentication parameters"; container authentication-params { if-feature twamp-light-authentication; presence "Enables TWAMP Light authentication"; description "Parameters for TWAMP Light authentication"; leaf key-chain { type kc:key-chain-ref; description "Name of key-chain"; } } } /*Configuration Data*/ container twamp-light { description "Top level container for TWAMP-Light configuration"; container twamp-light-session-sender { if-feature session-sender-light; description "TWAMP-Light Session-Sender container"; leaf sender-light-enable { type enable; default "true"; description "Whether this network element is enabled to act as TWAMP-Light Sender"; } list test-session { key "session-id"; unique "sender-ip sender-udp-port reflector-ip" +" reflector-udp-port dscp-value"; description "This structure is a container of test session managed objects"; leaf session-id { type uint32; Mirsky, et al. Expires October 15, 2017 [Page 13] Internet-Draft TWAMP Light data model April 2017 description "Session ID"; } leaf test-session-enable { type enable; default "true"; description "Whether this TWAMP Test session is enabled"; } leaf number-of-packets { type union { type uint32 { range 1..4294967294 { description "The overall number of UDP test packet to be transmitted by the sender for this test session"; } } type enumeration { enum forever { description "Indicates that the test session SHALL be run *forever*."; } } } default 10; description "This value determines if the TWAMP-Test session is bound by number of test packets or not."; } leaf packet-padding-size { type uint32; default 27; description "Size of the Packet Padding. Suggested to run Path MTU Discovery to avoid packet fragmentation in IPv4 and packet blackholing in IPv6"; } leaf interval { type uint32; units microseconds; description "Time interval between transmission of two Mirsky, et al. Expires October 15, 2017 [Page 14] Internet-Draft TWAMP Light data model April 2017 consecutive packets in the test session in microseconds"; } leaf session-timeout { when "../number-of-packets != 'forever'" { description "Test session timeout only valid if the test mode is periodic."; } type uint32; units "seconds"; default 900; description "The timeout value for the Session-Sender to collect outstanding reflected packets."; } leaf measurement-interval { when "../number-of-packets = 'forever'" { description "Valid only when the test to run forever, i.e. continiously."; } type uint32; units "seconds"; default 60; description "Interval to calculate performance metric when the test mode is 'continuous'."; } leaf repeat { type union { type uint32 { range 0..4294967294; } type enumeration { enum forever { description "Indicates that the test session SHALL be repeated *forever* using the information in repeat-interval parameter, and SHALL NOT decrement the value."; } } } Mirsky, et al. Expires October 15, 2017 [Page 15] Internet-Draft TWAMP Light data model April 2017 default 0; description "This value determines if the TWAMP-Test session must be repeated. When a test session has completed, the repeat parameter is checked. The default value of 0 indicates that the session MUST NOT be repeated. If the repeat value is 1 through 4,294,967,294 then the test session SHALL be repeated using the information in repeat-interval parameter. The implementation MUST decrement the value of repeat after determining a repeated session is expected."; } leaf repeat-interval { when "../repeat != 0"; type uint32; units seconds; default 0; description "This parameter determines the timing of repeated TWAMP-Test sessions when repeat is more than 0."; } leaf dscp-value { type inet:dscp; default 0; description "DSCP value to be set in the test packet."; } leaf test-session-relector-mode { type session-reflector-mode; default "stateless"; description "The mode of TWAMP-Reflector for the test session."; } uses session-light-parameters; uses session-light-auth-params; } } container twamp-light-session-reflector { if-feature session-reflector-light; description "TWAMP-Light Session-Reflector container"; leaf reflector-light-enable { type enable; Mirsky, et al. Expires October 15, 2017 [Page 16] Internet-Draft TWAMP Light data model April 2017 default "true"; description "Whether this network element is enabled to act as TWAMP-Light Reflector"; } leaf ref-wait { type uint32 { range 1..604800; } units seconds; default 900; description "REFWAIT(TWAMP test session timeout in seconds), the default value is 900"; } leaf reflector-light-mode-state { type session-reflector-mode; default stateless; description "The state of the mode of the TWAMP-Light Session-Reflector"; } list test-session { key "session-id"; unique "sender-ip sender-udp-port reflector-ip" +" reflector-udp-port"; description "This structure is a container of test session managed objects"; leaf session-id { type uint32; description "Session ID"; } leaf dscp-handling-mode { type session-dscp-mode; default copy-received-value; description "Session-Reflector handling of DSCP: - use value copied from received TWAMP-Test packet; - use value explicitly configured"; } leaf dscp-value { Mirsky, et al. Expires October 15, 2017 [Page 17] Internet-Draft TWAMP Light data model April 2017 when "../dscp-handling-mode = 'use-configured-value'"; type inet:dscp; default 0; description "DSCP value to be set in the reflected packet if dscp-handling-mode is set to use-configured-value."; } uses session-light-parameters; uses session-light-auth-params; } } } /*Operational state data nodes*/ container twamp-light-state{ config "false"; description "Top level container for TWAMP-Light state data"; container twamp-light-session-sender-state { if-feature session-sender-light; description "Session-Sender container for state data"; list test-session-state{ key "session-id"; description "This structure is a container of test session managed objects"; leaf session-id { type uint32; description "Session ID"; } leaf sender-session-state { type enumeration { enum active { description "Test session is active"; } enum ready { description "Test session is idle"; } } description "State of the particular TWAMP-Light test session at the sender"; } Mirsky, et al. Expires October 15, 2017 [Page 18] Internet-Draft TWAMP Light data model April 2017 container current-stats { description "This container contains the results for the current Measurement Interval in a Measurement session "; leaf start-time { type yang:date-and-time; mandatory true; description "The time that the current Measurement Interval started"; } leaf number-of-packets { type uint32; description "The overall number of UDP test packets to be transmitted by the sender for this test session"; } leaf packet-padding-size { type uint32; default 27; description "Size of the Packet Padding. Suggested to run Path MTU Discovery to avoid packet fragmentation in IPv4 and packet backholing in IPv6"; } leaf interval { type uint32; units microseconds; description "Time interval between transmission of two consecutive packets in the test session"; } leaf duplicate-packets { type uint32; description "Duplicate packets"; } leaf reordered-packets { type uint32; description "Reordered packets"; } uses session-light-parameters; leaf dscp { type inet:dscp; description "The DSCP value that was placed in the header of Mirsky, et al. Expires October 15, 2017 [Page 19] Internet-Draft TWAMP Light data model April 2017 TWAMP UDP test packets by the Session-Sender."; } uses maintenance-statistics; container two-way-delay { description "two way delay result of the test session"; uses delay-statistics; } container one-way-delay-far-end { description "one way delay far-end of the test session"; uses delay-statistics; } container one-way-delay-near-end { description "one way delay near-end of the test session"; uses delay-statistics; } container two-way-loss { description "two way loss count and ratio result of the test session"; uses packet-loss-statistics; } container one-way-loss-far-end { when "/twamp-light/twamp-light-session-sender/" +"test-session[session-id]/" +"test-session-relector-mode = 'stateful'" { description "One-way statistic is only valid id the session-reflector is in stateful mode."; } description "one way loss count and ratio far-end of the test session"; uses packet-loss-statistics; } container one-way-loss-near-end { when "/twamp-light/twamp-light-session-sender/" +"test-session[session-id]/" +"test-session-relector-mode = 'stateful'" { description "One-way statistic is only valid id the session-reflector is in stateful mode."; } description Mirsky, et al. Expires October 15, 2017 [Page 20] Internet-Draft TWAMP Light data model April 2017 "one way loss count and ratio near-end of the test session"; uses packet-loss-statistics; } } list history-stats { key id; description "This container contains the results for the history Measurement Interval in a Measurement session "; leaf id { type uint32; description "The identifier for the Measurement Interval within this session"; } leaf end-time { type yang:date-and-time; mandatory true; description "The time that the Measurement Interval ended"; } leaf number-of-packets { type uint32; description "The overall number of UDP test packets to be transmitted by the sender for this test session"; } leaf packet-padding-size { type uint32; default 27; description "Size of the Packet Padding. Suggested to run Path MTU Discovery to avoid packet fragmentation in IPv4 and packet blackholing in IPv6"; } leaf interval { type uint32; units microseconds; description "Time interval between transmission of two consecutive packets in the test session"; } leaf duplicate-packets { type uint32; Mirsky, et al. Expires October 15, 2017 [Page 21] Internet-Draft TWAMP Light data model April 2017 description "Duplicate packets"; } leaf reordered-packets { type uint32; description "Reordered packets"; } leaf loss-packets { type uint32; description "Loss packets"; } uses session-light-parameters; leaf dscp { type inet:dscp; description "The DSCP value that was placed in the header of TWAMP UDP test packets by the Session-Sender."; } uses maintenance-statistics; container two-way-delay{ description "two way delay result of the test session"; uses delay-statistics; } container one-way-delay-far-end{ description "one way delay far end of the test session"; uses delay-statistics; } container one-way-delay-near-end{ description "one way delay near end of the test session"; uses delay-statistics; } } } } container twamp-light-session-reflector-state { if-feature session-reflector-light; description "TWAMP-Light Session-Reflector container for state data"; leaf reflector-light-admin-status { type boolean; mandatory "true"; description Mirsky, et al. Expires October 15, 2017 [Page 22] Internet-Draft TWAMP Light data model April 2017 "Whether this network element is enabled to act as TWAMP-Light Reflector"; } list test-session-state { key "session-id"; description "This structure is a container of test session managed objects"; leaf session-id { type uint32; description "Session ID"; } uses maintenance-statistics; uses session-light-parameters; } } } rpc twamp-sender-start { description "start the configured sender session"; input { leaf session-id { type uint32; mandatory true; description "The session to be started"; } } } rpc twamp-sender-stop { description "stop the configured sender session"; input { leaf session-id { type uint32; mandatory true; description "The session to be stopped"; } } } } Mirsky, et al. Expires October 15, 2017 [Page 23] Internet-Draft TWAMP Light data model April 2017 4. IANA Considerations This document registers a URI in the IETF XML registry [RFC3688]. Following the format in [RFC3688], the following registration is requested to be made. URI: urn:ietf:params:xml:ns:yang:ietf-twamp-light Registrant Contact: The IPPM WG of the IETF. XML: N/A, the requested URI is an XML namespace. This document registers a YANG module in the YANG Module Names registry [RFC6020]. name: ietf-twamp-light namespace: urn:ietf:params:xml:ns:yang:ietf-twamp-light prefix: twamp reference: RFC XXXX 5. Security Considerations The configuration, state, action data defined in this document may be accessed via the NETCONF protocol [RFC6241]. SSH [RFC6242] is mandatory secure transport that is the lowest NETCONF layer. The NETCONF access control model [RFC6536] provides means to restrict access for particular NETCONF users to a pre-configured subset of all available NETCONF protocol operations and content. But, in general, this TWAMP Light YANG module does not change any underlying security issues that already may exist in [I-D.elteto-ippm-twamp-mib]. 6. Acknowledgements 7. References 7.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . Mirsky, et al. Expires October 15, 2017 [Page 24] Internet-Draft TWAMP Light data model April 2017 [RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, DOI 10.17487/RFC3688, January 2004, . [RFC5357] Hedayat, K., Krzanowski, R., Morton, A., Yum, K., and J. Babiarz, "A Two-Way Active Measurement Protocol (TWAMP)", RFC 5357, DOI 10.17487/RFC5357, October 2008, . [RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, October 2010, . [RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed., and A. Bierman, Ed., "Network Configuration Protocol (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011, . [RFC6242] Wasserman, M., "Using the NETCONF Protocol over Secure Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011, . [RFC6536] Bierman, A. and M. Bjorklund, "Network Configuration Protocol (NETCONF) Access Control Model", RFC 6536, DOI 10.17487/RFC6536, March 2012, . [RFC7750] Hedin, J., Mirsky, G., and S. Baillargeon, "Differentiated Service Code Point and Explicit Congestion Notification Monitoring in the Two-Way Active Measurement Protocol (TWAMP)", RFC 7750, DOI 10.17487/RFC7750, February 2016, . 7.2. Informative References [I-D.elteto-ippm-twamp-mib] Elteto, T. and G. Mirsky, "Two-Way Active Measurement Protocol (TWAMP) Management Information Base (MIB)", draft-elteto-ippm-twamp-mib-01 (work in progress), January 2014. [I-D.ietf-ippm-twamp-yang] Civil, R., Morton, A., Rahman, R., Jethanandani, M., and K. Pentikousis, "Two-Way Active Measurement Protocol (TWAMP) Data Model", draft-ietf-ippm-twamp-yang-03 (work in progress), February 2017. Mirsky, et al. Expires October 15, 2017 [Page 25] Internet-Draft TWAMP Light data model April 2017 Authors' Addresses Greg Mirsky ZTE Corp. Email: gregimirsky@gmail.com Xiao Min ZTE Corp. Email: xiao.min2@zte.com.cn Adrian Pan Ericsson Email: adrian.pan@ericsson.com Wei S Luo Ericsson Email: wei.s.luo@ericsson.com Mirsky, et al. Expires October 15, 2017 [Page 26]