SUIT B. Moran Internet-Draft H. Tschofenig Intended status: Informational Arm Limited Expires: January 9, 2020 H. Birkholz Fraunhofer SIT July 08, 2019 SUIT CBOR manifest serialisation format draft-moran-suit-manifest-05 Abstract This specification describes the format of a manifest. A manifest is a bundle of metadata about the firmware for an IoT device, where to find the firmware, the devices to which it applies, and cryptographic information protecting the manifest. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on January 9, 2020. Copyright Notice Copyright (c) 2019 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of Moran, et al. Expires January 9, 2020 [Page 1] Internet-Draft Firmware Manifest Format July 2019 the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. This document may contain material from IETF Documents or IETF Contributions published or made publicly available before November 10, 2008. The person(s) controlling the copyright in some of this material may not have granted the IETF Trust the right to allow modifications of such material outside the IETF Standards Process. Without obtaining an adequate license from the person(s) controlling the copyright in such materials, this document may not be modified outside the IETF Standards Process, and derivative works of it may not be created outside the IETF Standards Process, except to format it for publication as an RFC or to translate it into languages other than English. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Conventions and Terminology . . . . . . . . . . . . . . . . . 4 3. Distributing firmware . . . . . . . . . . . . . . . . . . . . 5 4. Workflow of a device applying a firmware update . . . . . . . 5 5. SUIT manifest goals . . . . . . . . . . . . . . . . . . . . . 6 6. SUIT manifest design overview . . . . . . . . . . . . . . . . 7 6.1. Manifest Design Evaluation . . . . . . . . . . . . . . . 8 6.2. Severable Elements . . . . . . . . . . . . . . . . . . . 9 6.3. Conventions . . . . . . . . . . . . . . . . . . . . . . . 9 6.4. Payloads . . . . . . . . . . . . . . . . . . . . . . . . 9 7. Manifest Structure . . . . . . . . . . . . . . . . . . . . . 10 7.1. Outer wrapper . . . . . . . . . . . . . . . . . . . . . . 11 7.2. Manifest . . . . . . . . . . . . . . . . . . . . . . . . 13 7.3. SUIT_Dependency . . . . . . . . . . . . . . . . . . . . . 16 7.4. SUIT_Component_Reference . . . . . . . . . . . . . . . . 17 7.5. Manifest Parameters . . . . . . . . . . . . . . . . . . . 17 7.5.1. SUIT_Parameter_Strict_Order . . . . . . . . . . . . . 19 7.5.2. SUIT_Parameter_Coerce_Condition_Failure . . . . . . . 20 7.6. SUIT_Parameter_Encryption_Info . . . . . . . . . . . . . 20 7.7. SUIT_Parameter_Compression_Info . . . . . . . . . . . . . 20 7.8. SUIT_Parameter_Unpack_Info . . . . . . . . . . . . . . . 20 7.9. SUIT_Parameters CDDL . . . . . . . . . . . . . . . . . . 21 7.10. SUIT_Command_Sequence . . . . . . . . . . . . . . . . . . 22 7.11. SUIT_Condition . . . . . . . . . . . . . . . . . . . . . 24 7.11.1. Identifier Conditions . . . . . . . . . . . . . . . 25 7.11.2. suit-condition-image-match . . . . . . . . . . . . . 25 7.11.3. suit-condition-image-not-match . . . . . . . . . . . 25 7.11.4. suit-condition-use-before . . . . . . . . . . . . . 25 7.11.5. suit-condition-minimum-battery . . . . . . . . . . . 25 7.11.6. suit-condition-update-authorised . . . . . . . . . . 26 7.11.7. suit-condition-version . . . . . . . . . . . . . . . 26 Moran, et al. Expires January 9, 2020 [Page 2] Internet-Draft Firmware Manifest Format July 2019 7.11.8. SUIT_Condition_Custom . . . . . . . . . . . . . . . 27 7.11.9. Identifiers . . . . . . . . . . . . . . . . . . . . 27 7.11.10. SUIT_Condition CDDL . . . . . . . . . . . . . . . . 29 7.12. SUIT_Directive . . . . . . . . . . . . . . . . . . . . . 29 7.12.1. suit-directive-set-component-index . . . . . . . . . 30 7.12.2. suit-directive-set-dependency-index . . . . . . . . 31 7.12.3. suit-directive-abort . . . . . . . . . . . . . . . . 31 7.12.4. suit-directive-run-sequence . . . . . . . . . . . . 31 7.12.5. suit-directive-try-each . . . . . . . . . . . . . . 32 7.12.6. suit-directive-process-dependency . . . . . . . . . 32 7.12.7. suit-directive-set-parameters . . . . . . . . . . . 33 7.12.8. suit-directive-override-parameters . . . . . . . . . 33 7.12.9. suit-directive-fetch . . . . . . . . . . . . . . . . 34 7.12.10. suit-directive-copy . . . . . . . . . . . . . . . . 34 7.12.11. suit-directive-swap . . . . . . . . . . . . . . . . 35 7.12.12. suit-directive-run . . . . . . . . . . . . . . . . . 35 7.12.13. suit-directive-wait . . . . . . . . . . . . . . . . 36 7.12.14. SUIT_Directive CDDL . . . . . . . . . . . . . . . . 37 8. Dependency processing . . . . . . . . . . . . . . . . . . . . 39 9. Access Control Lists . . . . . . . . . . . . . . . . . . . . 40 10. SUIT digest container . . . . . . . . . . . . . . . . . . . . 40 11. Creating conditional sequences . . . . . . . . . . . . . . . 41 12. Full CDDL . . . . . . . . . . . . . . . . . . . . . . . . . . 43 13. Examples . . . . . . . . . . . . . . . . . . . . . . . . . . 48 13.1. Example 0: . . . . . . . . . . . . . . . . . . . . . . . 48 13.2. Example 1: . . . . . . . . . . . . . . . . . . . . . . . 49 13.3. Example 2: . . . . . . . . . . . . . . . . . . . . . . . 52 13.4. Example 3: . . . . . . . . . . . . . . . . . . . . . . . 54 13.5. Example 4: . . . . . . . . . . . . . . . . . . . . . . . 57 13.6. Example 5: . . . . . . . . . . . . . . . . . . . . . . . 61 13.7. Example 6: . . . . . . . . . . . . . . . . . . . . . . . 65 14. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 68 15. Security Considerations . . . . . . . . . . . . . . . . . . . 68 16. Mailing List Information . . . . . . . . . . . . . . . . . . 69 17. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 69 18. References . . . . . . . . . . . . . . . . . . . . . . . . . 69 18.1. Normative References . . . . . . . . . . . . . . . . . . 69 18.2. Informative References . . . . . . . . . . . . . . . . . 70 18.3. URIs . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 71 1. Introduction A firmware update mechanism is an essential security feature for IoT devices to deal with vulnerabilities. While the transport of firmware images to the devices themselves is important there are already various techniques available, such as the Lightweight Machine-to-Machine (LwM2M) protocol offering device management of IoT Moran, et al. Expires January 9, 2020 [Page 3] Internet-Draft Firmware Manifest Format July 2019 devices. Equally important is the inclusion of meta-data about the conveyed firmware image (in the form of a manifest) and the use of end-to-end security protection to detect modifications and (optionally) to make reverse engineering more difficult. End-to-end security allows the author, who builds the firmware image, to be sure that no other party (including potential adversaries) can install firmware updates on IoT devices without adequate privileges. This authorization process is ensured by the use of dedicated symmetric or asymmetric keys installed on the IoT device: for use cases where only integrity protection is required it is sufficient to install a trust anchor on the IoT device. For confidentiality protected firmware images it is additionally required to install either one or multiple symmetric or asymmetric keys on the IoT device. Starting security protection at the author is a risk mitigation technique so firmware images and manifests can be stored on untrusted respositories; it also reduces the scope of a compromise of any repository or intermediate system to be no worse than a denial of service. It is assumed that the reader is familiar with the high-level firmware update architecture [Architecture]. The SUIT manifest is heavily optimised for consumption by constrained devices. This means that it is not constructed as a conventional descriptive document. Instead, of describing what an update IS, it describes what a recipient should DO. While the SUIT manifest is informed by and optimised for firmware update use cases, there is nothing in the [Information] that restricts its use to only firmware use cases. Software update and delivery of arbitrary data can equally be managed by SUIT-based metadata. 2. Conventions and Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. - SUIT: Sofware Update for the Internet of Things, the IETF working group for this standard. - Payload: A piece of information to be delivered. Typically Firmware for the purposes of SUIT. - Resource: A piece of information that is used to construct a payload. Moran, et al. Expires January 9, 2020 [Page 4] Internet-Draft Firmware Manifest Format July 2019 - Manifest: A piece of information that describes one or more payloads, one or more resources, and the processors needed to transform resources into payloads. - Update: One or more manifests that describe one or more payloads. - Update Authority: The owner of a cryptographic key used to sign updates, trusted by recipient devices. - Recipient: The system, typically an IoT device, that receives a manifest. - Condition: A test for a property of the Recipient or its components. - Directive: An action for the Recipient to perform. - Command: A Condition or a Directive. - Trusted Execution: A process by which a system ensures that only trusted code is executed, for example secure boot. 3. Distributing firmware Distributing firmware in a multi-party environment is a difficult operation. Each party requires a different subset of data. Some data may not be accessible to all parties. Multiple signatures may be required from parties with different authorities. This topic is covered in more depth in [Architecture]. 4. Workflow of a device applying a firmware update The manifest is designed to work with a pull parser, where each section of the manifest is used in sequence. The expected workflow for a device installing an update can be broken down into 5 steps: 1. Verify the signature of the manifest 2. Verify the applicability of the manifest 3. Resolve dependencies 4. Fetch payload(s) 5. Install payload(s) When installation is complete, similar information can be used for validating and running images in a further three steps: Moran, et al. Expires January 9, 2020 [Page 5] Internet-Draft Firmware Manifest Format July 2019 1. Verify image(s) 2. Load image(s) 3. Run image(s) When multiple manifests are used for an update, each manifest's steps occur in a lockstep fashion; all manifests have dependency resolution performed before any manifest performs a payload fetch, etc. 5. SUIT manifest goals The manifest described in this document is intended to meet several goals, as described below. 1. Meet the requirements defined in [Information]. 2. Simple to parse on a constrained node 3. Simple to process on a constrained node 4. Compact encoding 5. Comprehensible by an intermediate system 6. Expressive enough to enable advanced use cases on advanced nodes 7. Extensible The SUIT manifest can be used for a variety of purposes throughout its lifecycle. The manifest allows: 1. the Firmware Author to reason about releasing a firmware. 2. the Network Operator to reason about compatibility of a firmware. 3. the Device Operator to reason about the impact of a firmware. 4. the Device Operator to manage distribution of firmware to devices. 5. the Plant Manager to reason about timing and acceptance of firmware updates. 6. the device to reason about the authority & authenticity of a firmware prior to installation. 7. the device to reason about the applicability of a firmware. Moran, et al. Expires January 9, 2020 [Page 6] Internet-Draft Firmware Manifest Format July 2019 8. the device to reason about the installation of a firmware. 9. the device to reason about the authenticity & encoding of a firmware at boot. Each of these uses happens at a different stage of the manifest lifecycle, so each has different requirements. 6. SUIT manifest design overview In order to provide flexible behaviour to constrained devices, while still allowing more powerful devices to use their full capabilities, the SUIT manifest encodes the required behaviour of a Recipient device. Behaviour is encoded as a specialised byte code, contained in a CBOR list. This promotes a flat encoding, which simplifies the parser. The information encoded by this byte code closely matches the operations that a device will perform, which promotes ease of processing. The core operations used by most update and trusted execution operations are represented in the byte code. The byte code can be extended by registering new operations. The specialised byte code approach gives benefits equivalent to those provided by a scripting language or conventional byte code, with two substantial differences. First, the language is extremely high level, consisting of only the operations that a device may perform during update and trusted execution of a firmware image. Second, the language specifies behaviours in a linearised form, without reverse branches. Conditional processing is supported, and parallel and out- of-order processing may be performed by sufficiently capable devices. By structuring the data in this way, the manifest processor becomes a very simple engine that uses a pull parser to interpret the manifest. This pull parser invokes a series of command handlers that evaluate a Condition or execute a Directive. Most data is structured in a highly regular pattern, which simplifies the parser. The results of this allow a Recipient to implement a very small parser for constrained applications. If needed, such a parser also allows the Recipient to perform complex updates with reduced overhead. Conditional execution of commands allows a simple device to perform important decisions at validation-time. Dependency handling is vastly simplified as well. Dependencies function like subroutines of the language. When a manifest has a dependency, it can invoke that dependency's commands and modify their behaviour by setting parameters. Because some parameters come with security implications, the dependencies also have a mechanism to reject modifications to parameters on a fine-grained level. Moran, et al. Expires January 9, 2020 [Page 7] Internet-Draft Firmware Manifest Format July 2019 Developing a robust permissions system works in this model too. The Recipient can use a simple ACL that is a table of Identities and Component Identifier permissions to ensure that only manifests authenticated by the appropriate identity have access to operate on a component. Capability reporting is similarly simplified. A Recipient can report the Commands, Parameters, Algorithms, and Component Identifiers that it supports. This is sufficiently precise for a manifest author to create a manifest that the Recipient can accept. The simplicity of design in the Recipient due to all of these benefits allows even a highly constrained platform to use advanced update capabilities. 6.1. Manifest Design Evaluation To evaluate this design, it is compared to the goals stated above. Goal evaluation: 1. Each command and condition is anchored to a manifest information element in [Information] 2. The use of a byte code encourages flat encoding and reduces nesting depth. This promotes a simple encoding. 3. The encoded information closely matches the operations that a device will perform, making the format easy to process. 4. Encoding efficiency exceeds 50% when compared to raw data. 5. Tooling will be required to reason about the manifest. 6. The core operations used by most update and trusted execution operations are represented in the byte code. The use cases listed in [Information] are enabled. 7. Registration of new standard byte code identifiers enables extension in a comprehensible way. The manifest described by this document meets the stated goals. Meeting goal 5-comprehensible by intermediate systems-will require additional tooling or a division of metadata. Moran, et al. Expires January 9, 2020 [Page 8] Internet-Draft Firmware Manifest Format July 2019 6.2. Severable Elements Because the manifest can be used by different actors at different times, some parts of the manifest can be removed without affecting later stages of the lifecycle. This is called "Severing." Severing of information is achieved by separating that information from the signed container so that removing it does not affect the signature. This means that ensuring authenticity of severable parts of the manifest is a requirement for the signed portion of the manifest. Severing some parts makes it possible to discard parts of the manifest that are no longer necessary. This is important because it allows the storage used by the manifest to be greatly reduced. For example, no text size limits are needed if text is removed from the manifest prior to delivery to a constrained device. Elements are made severable by removing them from the manifest, encoding them in a bstr, and placing a SUIT_Digest of the bstr in the manifest so that they can still be authenticated. The SUIT_Digest typically consumes 4 bytes more than the size of the raw digest, therefore elements smaller than (Digest Bits)/8 + 4 SHOULD never be severable. Elements larger than (Digest Bits)/8 + 4 MAY be severable, while elements that are much larger than (Digest Bits)/8 + 4 SHOULD be severable. 6.3. Conventions The map indices in this encoding are reset to 1 for each map within the structure. This is to keep the indices as small as possible. The goal is to keep the index objects to single bytes (CBOR positive integers 1-23). Wherever enumerations are used, they are started at 1. This allows detection of several common software errors that are caused by uninitialised variables. Positive numbers in enumerations are reserved for IANA registration. Negative numbers are used to identify application-specific implementations. CDDL names are hyphenated and CDDL structures follow the convention adopted in COSE [RFC8152]: SUIT_Structure_Name. 6.4. Payloads Payloads can take many forms, for example, binary, hex, s-record, elf, binary diff, PEM certificate, CBOR Web Token, serialised configuration. These payloads fall into two broad categories: those that require installation-time unpacking and those that do not. Binary, PEM certificate, and CBOR Web Token do not require installation-time unpacking. Hex, s-record, and serialised Moran, et al. Expires January 9, 2020 [Page 9] Internet-Draft Firmware Manifest Format July 2019 configuration require installation-time unpacking. Elf may or may not require unpacking depending on the target. Some payloads cannot be directly converted to a writable binary stream. Hex, s-record, and elf may contain gaps and they have no guarantee of monotonic increase of address, which makes pre- processing them into a binary stream difficult on constrained platforms. Serialised configuration may be unpacked into a configuration database, which makes it impossible to preprocess into a binary stream, suitable for direct writing. Where a specialised unpacking algorithm is needed, a digest is not always calculable over an installed payload. For example, an elf, s-record or hex file may contain gaps that can contain any data, while not changing whether or not an installed payload is valid. Serialised configuration may update only some device data rather than all of it. This means that the digest cannot always be calculated over an installed payload when a specialised installer is used. This presents two problems for the manifest: first, it must indicate that a specialised installer is needed and, second, it cannot provide a hash of the payload that is checkable after installation. These two problems are resolved in two ways: 1. Payloads that need a specialised installer must indicate this in suit-payload-info-unpack. 2. Payloads that need specialised verification must indicate this in the SUIT_Parameter_Image_Digest by indicating a SUIT_Digest algorithm that correctly validates their information. 7. Manifest Structure The manifest is divided into several sections in a hierarchy as follows: 1. The outer wrapper 1. The authentication wrapper 2. The manifest 1. Critical Information 2. Information shared by all command sequences 1. List of dependencies Moran, et al. Expires January 9, 2020 [Page 10] Internet-Draft Firmware Manifest Format July 2019 2. List of payloads 3. List of payloads in dependencies 4. Common list of conditions, directives 3. Dependency resolution Reference or list of conditions, directives 4. Payload fetch Reference or list of conditions, directives 5. Installation Reference or list of conditions, directives 6. Verification conditions/directives 7. Load conditions/directives 8. Run conditions/directives 9. Text / Reference 10. COSWID / Reference 3. Dependency resolution conditions/directives 4. Payload fetch conditions/directives 5. Installation conditions/directives 6. Text 7. COSWID / Reference 8. Intermediate Certificate(s) / CWTs 9. Inline Payload(s) 7.1. Outer wrapper This object is a container for the other pieces of the manifest to provide a common mechanism to find each of the parts. All elements of the outer wrapper are contained in bstr objects. Wherever the manifest references an object in the outer wrapper, the bstr is included in the digest calculation. The CDDL that describes the wrapper is below Moran, et al. Expires January 9, 2020 [Page 11] Internet-Draft Firmware Manifest Format July 2019 SUIT_Outer_Wrapper = { suit-authentication-wrapper => bstr .cbor SUIT_Authentication_Wrapper / nil, $SUIT_Manifest_Wrapped, ? suit-dependency-resolution => bstr .cbor SUIT_Command_Sequence, ? suit-payload-fetch => bstr .cbor SUIT_Command_Sequence, ? suit-install => bstr .cbor SUIT_Command_Sequence, ? suit-text-external => bstr .cbor SUIT_Text_Info, ? suit-coswid-external => bstr .cbor COSWID } SUIT_Authentication_Wrapper = [ + (COSE_Mac_Tagged / COSE_Sign_Tagged / COSE_Mac0_Tagged / COSE_Sign1_Tagged)] SUIT_Encryption_Wrapper = COSE_Encrypt_Tagged / COSE_Encrypt0_Tagged SUIT_Manifest_Wrapped //= (suit-manifest => bstr .cbor SUIT_Manifest) SUIT_Manifest_Wrapped //= ( suit-manifest-encryption-info => bstr .cbor SUIT_Encryption_Wrapper, suit-manifest-encrypted => bstr ) All elements of the outer wrapper must be wrapped in a bstr to minimize the complexity of the code that evaluates the cryptographic integrity of the element and to ensure correct serialisation for integrity and authenticity checks. The suit-authentication-wrapper contains a list of 1 or more cryptographic authentication wrappers for the core part of the manifest. These are implemented as COSE_Mac_Tagged or COSE_Sign_Tagged blocks. The Manifest is authenticated by these blocks in "detached payload" mode. The COSE_Mac_Tagged and COSE_Sign_Tagged blocks are described in RFC 8152 [RFC8152] and are beyond the scope of this document. The suit-authentication-wrapper MUST come first in the SUIT_Outer_Wrapper, regardless of canonical encoding of CBOR. All validators MUST reject any SUIT_Outer_Wrapper that begins with any element other than a suit-authentication- wrapper. A manifest that has not had authentication information added MUST still contain the suit-authentication-wrapper element, but the content MUST be nil. The outer wrapper MUST contain only one of - a plaintext manifest: SUIT_Manifest - an encrypted manifest: both a SUIT_Encryption_Wrapper and the ciphertext of a manifest. Moran, et al. Expires January 9, 2020 [Page 12] Internet-Draft Firmware Manifest Format July 2019 When the outer wrapper contains SUIT_Encryption_Wrapper, the suit- authentication-wrapper MUST authenticate the plaintext of suit- manifest-encrypted. suit-manifest contains a SUIT_Manifest structure, which describes the payload(s) to be installed and any dependencies on other manifests. suit-manifest-encryption-info contains a SUIT_Encryption_Wrapper, a COSE object that describes the information required to decrypt a ciphertext manifest. suit-manifest-encrypted contains a ciphertext manifest. Each of suit-dependency-resolution, suit-payload-fetch, and suit- payload-installation contain the severable contents of the identically named portions of the manifest, described in Section 7.2. suit-text contains all the human-readable information that describes any and all parts of the manifest, its payload(s) and its resource(s). suit-coswid contains a Concise Software Identifier. This may be discarded by the recipient if not needed. 7.2. Manifest The manifest describes the critical metadata for the referenced payload(s). In addition, it contains: 1. a version number for the manifest structure itself 2. a sequence number 3. a list of dependencies 4. a list of components affected 5. a list of components affected by dependencies 6. a reference for each of the severable blocks. 7. a list of actions that the recipient should perform. The following CDDL fragment defines the manifest. Moran, et al. Expires January 9, 2020 [Page 13] Internet-Draft Firmware Manifest Format July 2019 SUIT_Manifest = { suit-manifest-version => 1, suit-manifest-sequence-number => uint, suit-common => bstr .cbor SUIT_Common, ? suit-dependency-resolution => Digest / bstr .cbor SUIT_Command_Sequence, ? suit-payload-fetch => Digest / bstr .cbor SUIT_Command_Sequence, ? suit-install => Digest / bstr .cbor SUIT_Command_Sequence ? suit-validate => bstr .cbor SUIT_Command_Sequence ? suit-load => bstr .cbor SUIT_Command_Sequence ? suit-run => bstr .cbor SUIT_Command_Sequence ? suit-text-info => Digest / bstr .cbor SUIT_Text_Map ? suit-coswid => Digest / bstr .cbor COSWID } SUIT_Common = { ? suit-dependencies => bstr .cbor [ + SUIT_Dependency ], ? suit-components => bstr .cbor [ + SUIT_Component_Identifier ], ? suit-dependency-components => bstr .cbor [ + SUIT_Component_Reference ], ? suit-common-sequence => bstr .cbor SUIT_Command_Sequence, } Several fields in the Manifest can be either a CBOR structure or a SUIT_Digest. In each of these cases, the SUIT_Digest provides for a severable field. Severable fields are RECOMMENDED to implement. In particular, text SHOULD be severable, since most useful text elements occupy more space than a SUIT_Digest, but are not needed by recipient devices. Because SUIT_Digest is a CBOR Array and each severable element is a CBOR bstr, it is straight-forward for a recipient to determine whether an element is been severable. The key used for a severable element is the same in the SUIT_Manifest and in the SUIT_Outer_Wrapper so that a recipient can easily identify the correct data in the outer wrapper. The suit-manifest-version indicates the version of serialisation used to encode the manifest. Version 1 is the version described in this document. suit-manifest-version is REQUIRED. The suit-manifest-sequence-number is a monotonically increasing anti- rollback counter. It also helps devices to determine which in a set of manifests is the "root" manifest in a given update. Each manifest MUST have a sequence number higher than each of its dependencies. Each recipient MUST reject any manifest that has a sequence number lower than its current sequence number. It MAY be convenient to use a UTC timestamp in seconds as the sequence number. suit-manifest- sequence-number is REQUIRED. suit-common encodes all the information that is shared between each of the command sequences, including: suit-dependencies, suit- Moran, et al. Expires January 9, 2020 [Page 14] Internet-Draft Firmware Manifest Format July 2019 components, suit-dependency-components, and suit-common-sequence. suit-common is REQUIRED to implement. suit-dependencies is a list of SUIT_Dependency blocks that specify manifests that must be present before the current manifest can be processed. suit-dependencies is OPTIONAL to implement. In order to distinguish between components that are affected by the current manifest and components that are affected by a dependency, they are kept in separate lists. Components affected by the current manifest only list the component identifier. Components affected by a dependency include the component identifier and the index of the dependency that defines the component. suit-components is a list of SUIT_Component blocks that specify the component identifiers that will be affected by the content of the current manifest. suit-components is OPTIONAL, but at least one manifest MUST contain a suit-components block. suit-dependency-components is a list of SUIT_Component_Reference blocks that specify component identifiers that will be affected by the content of a dependency of the current manifest. suit-dependency- components is OPTIONAL. suit-common-sequence is a SUIT_Command_Sequence to execute prior to executing any other command sequence. Typical actions in suit- common-sequence include setting expected device identity and image digests when they are conditional (see Section 11 for more information on conditional sequences). suit-common-sequence is RECOMMENDED. suit-dependency-resolution is a SUIT_Command_Sequence to execute in order to perform dependency resolution. Typical actions include configuring URIs of dependency manifests, fetching dependency manifests, and validating dependency manifests' contents. suit- dependency-resolution is REQUIRED when suit-dependencies is present. suit-payload-fetch is a SUIT_Command_Sequence to execute in order to obtain a payload. Some manifests may include these actions in the suit-install section instead if they operate in a streaming installation mode. This is particularly relevant for constrained devices without any temporary storage for staging the update. suit- payload-fetch is OPTIONAL. suit-install is a SUIT_Command_Sequence to execute in order to install a payload. Typical actions include verifying a payload stored in temporary storage, copying a staged payload from temporary storage, and unpacking a payload. suit-install is OPTIONAL. Moran, et al. Expires January 9, 2020 [Page 15] Internet-Draft Firmware Manifest Format July 2019 suit-validate is a SUIT_Command_Sequence to execute in order to validate that the result of applying the update is correct. Typical actions involve image validation and manifest validation. suit- validate is REQUIRED. If the manifest contains dependencies, one process-dependency invocation per dependency or one process- dependency invocation targeting all dependencies SHOULD be present in validate. suit-load is a SUIT_Command_Sequence to execute in order to prepare a payload for execution. Typical actions include copying an image from permanent storage into RAM, optionally including actions such as decryption or decompression. suit-load is OPTIONAL. suit-run is a SUIT_Command_Sequence to execute in order to run an image. suit-run typically contains a single instruction: either the "run" directive for the bootable manifest or the "process dependencies" directive for any dependents of the bootable manifest. suit-run is OPTIONAL. Only one manifest in an update may contain the "run" directive. suit-text-info is a digest that uniquely identifies the content of the Text that is packaged in the OuterWrapper. text is OPTIONAL. suit-coswid is a digest that uniquely identifies the content of the concise-software-identifier that is packaged in the OuterWrapper. coswid is OPTIONAL. 7.3. SUIT_Dependency SUIT_Dependency specifies a manifest that describes a dependency of the current manifest. The following CDDL describes the SUIT_Dependency structure. SUIT_Dependency = { suit-dependency-digest => SUIT_Digest, ? suit-dependency-prefix => SUIT_Component_Identifier, } The suit-dependency-digest specifies the dependency manifest uniquely by identifying a particular Manifest structure. The digest is calculated over the Manifest structure instead of the COSE Sig_structure or Mac_structure. This means that a digest may need to be calculated more than once, however this is necessary to ensure that removing a signature from a manifest does not break dependencies due to missing signature elements. This is also necessary to support the trusted intermediary use case, where an intermediary re-signs the Moran, et al. Expires January 9, 2020 [Page 16] Internet-Draft Firmware Manifest Format July 2019 Manifest, removing the original signature, potentially with a different algorithm, or trading COSE_Sign for COSE_Mac. The suit-dependency-prefix element contains a SUIT_Component_Identifier. This specifies the scope at which the dependency operates. This allows the dependency to be forwarded on to a component that is capable of parsing its own manifests. It also allows one manifest to be deployed to multiple dependent devices without those devices needing consistent component hierarchy. This element is OPTIONAL. 7.4. SUIT_Component_Reference The SUIT_Component_Reference describes an image that is defined by another manifest. This is useful for overriding the behaviour of another manifest, for example by directing the recipient to look at a different URI for the image or by changing the expected format, such as when a gateway performs decryption on behalf of a constrained device. The following CDDL describes the SUIT_Component_Reference. SUIT_Component_Reference = { suit-component-identifier => SUIT_Component_Identifier, suit-component-dependency-index => uint } 7.5. Manifest Parameters Many conditions and directives require additional information. That information is contained within parameters that can be set in a consistent way. Parameters MUST only be: 1. Integers 2. Byte strings 3. Booleans This allows reduction of manifest size and replacement of parameters from one manifest to the next. Byte strings MAY contain CBOR-encoded objects. The defined manifest parameters are described below. +--------+-------+------+---------------+----------+----------------+ | Parame | CBOR | Defa | Scope | Name | Description | | ter | Type | ult | | | | | Code | | | | | | +--------+-------+------+---------------+----------+----------------+ | 1 | boole | True | Global | Strict | Requires that | | | an | | | Order | the manifest | Moran, et al. Expires January 9, 2020 [Page 17] Internet-Draft Firmware Manifest Format July 2019 | | | | | | is processed | | | | | | | in a strictly | | | | | | | linear | | | | | | | fashion. Set | | | | | | | to 0 to enable | | | | | | | parallel | | | | | | | handling of | | | | | | | manifest | | | | | | | directives. | | | | | | | | | 2 | boole | Fals | Command | Coerce C | Coerces the | | | an | e | Segment | ondition | success code | | | | | | Failure | of a command | | | | | | | segment to | | | | | | | success even | | | | | | | when aborted | | | | | | | due to a | | | | | | | condition | | | | | | | failure. | | | | | | | | | 3 | bstr | nil | Component/Glo | Vendor | A RFC4122 UUID | | | | | bal | ID | representing | | | | | | | the vendor of | | | | | | | the device or | | | | | | | component | | | | | | | | | 4 | bstr | nil | Component/Glo | Class ID | A RFC4122 UUID | | | | | bal | | representing | | | | | | | the class of | | | | | | | the device or | | | | | | | component | | | | | | | | | 5 | bstr | nil | Component/Glo | Device | A RFC4122 UUID | | | | | bal | ID | representing | | | | | | | the device or | | | | | | | component | | | | | | | | | 6 | bstr | nil | Component/Dep | URI | A URI from | | | | | endency | | which to fetch | | | | | | | a resource | | | | | | | | | 7 | bstr | nil | Component/Dep | Encrypti | A COSE object | | | | | endency | on Info | defining the | | | | | | | encryption | | | | | | | mode of a | | | | | | | resource | | | | | | | | | 8 | bstr | nil | Component | Compress | A SUIT_Compres | Moran, et al. Expires January 9, 2020 [Page 18] Internet-Draft Firmware Manifest Format July 2019 | | | | | ion Info | sion_Info | | | | | | | object | | | | | | | | | 9 | bstr | nil | Component | Unpack | A SUIT_Unpack_ | | | | | | Info | Info object | | | | | | | | | 10 | uint | nil | Component | Source C | A Component | | | | | | omponent | Index | | | | | | | | | 11 | bstr | nil | Component/Dep | Image | A SUIT_Digest | | | | | endency | Digest | | | | | | | | | | 12 | bstr | nil | Component/Dep | Image | Integer size | | | | | endency | Size | | | | | | | | | | 24 | bstr | nil | Component/Dep | URI List | A CBOR encoded | | | | | endency | | list of ranked | | | | | | | URIs | | | | | | | | | 25 | boole | Fals | Component/Dep | URI List | A CBOR encoded | | | an | e | endency | Append | list of ranked | | | | | | | URIs | | | | | | | | | nint | int/b | nil | Custom | Custom P | Application- | | | str | | | arameter | defined | | | | | | | parameter | +--------+-------+------+---------------+----------+----------------+ CBOR-encoded object parameters are still wrapped in a bstr. This is because it allows a parser that is aggregating parameters to reference the object with a single pointer and traverse it without understanding the contents. This is important for modularisation and division of responsibility within a pull parser. The same consideration does not apply to Conditions and Directives because those elements are invoked with their arguments immediately 7.5.1. SUIT_Parameter_Strict_Order The Strict Order Parameter allows a manifest to govern when directives can be executed out-of-order. This allows for systems that have a sensitivity to order of updates to choose the order in which they are executed. It also allows for more advanced systems to parallelise their handling of updates. Strict Order defaults to True. It MAY be set to False when the order of operations does not matter. When arriving at the end of a command sequence, ALL commands MUST have completed, regardless of the state of SUIT_Parameter_Strict_Order. If SUIT_Parameter_Strict_Order is Moran, et al. Expires January 9, 2020 [Page 19] Internet-Draft Firmware Manifest Format July 2019 returned to True, ALL preceding commands MUST complete before the next command is executed. 7.5.2. SUIT_Parameter_Coerce_Condition_Failure When executing a command sequence inside SUIT_Run_Sequence and a condition failure occurs, the manifest processor aborts the sequence. If Coerce Condition Failure is True, it returns Success. Otherwise, it returns the original condition failure. SUIT_Parameter_Coerce_Condition_Failure is scoped to the enclosing SUIT_Directive_Run_Sequence. Its value is discarded when SUIT_Directive_Run_Sequence terminates. 7.6. SUIT_Parameter_Encryption_Info Encryption Info defines the mechanism that Fetch or Copy should use to decrypt the data they transfer. SUIT_Parameter_Encryption_Info is encoded as a COSE_Encrypt_Tagged or a COSE_Encrypt0_Tagged, wrapped in a bstr 7.7. SUIT_Parameter_Compression_Info Compression Info defines any information that is required for a device to perform decompression operations. Typically, this includes the algorithm identifier. SUIT_Parameter_Compression_Info is defined by the following CDDL: SUIT_Compression_Info = { suit-compression-algorithm => SUIT_Compression_Algorithms ? suit-compression-parameters => bstr } SUIT_Compression_Algorithms /= SUIT_Compression_Algorithm_gzip SUIT_Compression_Algorithms /= SUIT_Compression_Algorithm_bzip2 SUIT_Compression_Algorithms /= SUIT_Compression_Algorithm_deflate SUIT_Compression_Algorithms /= SUIT_Compression_Algorithm_LZ4 SUIT_Compression_Algorithms /= SUIT_Compression_Algorithm_lzma 7.8. SUIT_Parameter_Unpack_Info SUIT_Unpack_Info defines the information required for a device to interpret a packed format, such as elf, hex, or binary diff. SUIT_Unpack_Info is defined by the following CDDL: Moran, et al. Expires January 9, 2020 [Page 20] Internet-Draft Firmware Manifest Format July 2019 SUIT_Unpack_Info = { suit-unpack-algorithm => SUIT_Unpack_Algorithms ? suit-unpack-parameters => bstr } SUIT_Unpack_Algorithms //= SUIT_Unpack_Algorithm_Delta SUIT_Unpack_Algorithms //= SUIT_Unpack_Algorithm_Hex SUIT_Unpack_Algorithms //= SUIT_Unpack_Algorithm_Elf 7.9. SUIT_Parameters CDDL The following CDDL describes all SUIT_Parameters. Moran, et al. Expires January 9, 2020 [Page 21] Internet-Draft Firmware Manifest Format July 2019 SUIT_Parameters //= (suit-parameter-strict-order => bool) SUIT_Parameters //= (suit-parameter-coerce-condition-failure => bool) SUIT_Parameters //= (suit-parameter-vendor-id => bstr) SUIT_Parameters //= (suit-parameter-class-id => bstr) SUIT_Parameters //= (suit-parameter-device-id => bstr) SUIT_Parameters //= (suit-parameter-uri => bstr) SUIT_Parameters //= (suit-parameter-encryption-info => bstr .cbor SUIT_Encryption_Info) SUIT_Parameters //= (suit-parameter-compression-info => bstr .cbor SUIT_Compression_Info) SUIT_Parameters //= (suit-parameter-unpack-info => bstr .cbor SUIT_Unpack_Info) SUIT_Parameters //= (suit-parameter-source-component => bstr .cbor SUIT_Component_Identifier) SUIT_Parameters //= (suit-parameter-image-digest => bstr .cbor SUIT_Digest) SUIT_Parameters //= (suit-parameter-image-size => uint) SUIT_Parameters //= (suit-parameter-uri-list => bstr .cbor SUIT_URI_List) SUIT_Parameters //= (suit-parameter_custom => int/bool/bstr) SUIT_URI_List = [ + [priority: int, uri: tstr] ] SUIT_Encryption_Info= COSE_Encrypt_Tagged/COSE_Encrypt0_Tagged SUIT_Compression_Info = { suit-compression-algorithm => SUIT_Compression_Algorithms ? suit-compression-parameters => bstr } SUIT_Compression_Algorithms /= SUIT_Compression_Algorithm_gzip SUIT_Compression_Algorithms /= SUIT_Compression_Algorithm_bzip2 SUIT_Compression_Algorithms /= SUIT_Compression_Algorithm_deflate SUIT_Compression_Algorithms /= SUIT_Compression_Algorithm_LZ4 SUIT_Compression_Algorithms /= SUIT_Compression_Algorithm_lzma SUIT_Unpack_Info = { suit-unpack-algorithm => SUIT_Unpack_Algorithms ? suit-unpack-parameters => bstr } SUIT_Unpack_Algorithms //= SUIT_Unpack_Algorithm_Delta SUIT_Unpack_Algorithms //= SUIT_Unpack_Algorithm_Hex SUIT_Unpack_Algorithms //= SUIT_Unpack_Algorithm_Elf 7.10. SUIT_Command_Sequence A SUIT_Command_Sequence defines a series of actions that the recipient MUST take to accomplish a particular goal. These goals are defined in the manifest and include: 1. Dependency Resolution 2. Payload Fetch Moran, et al. Expires January 9, 2020 [Page 22] Internet-Draft Firmware Manifest Format July 2019 3. Payload Installation 4. Image Validation 5. Image Loading 6. Run or Boot Each of these follows exactly the same structure to ensure that the parser is as simple as possible. Lists of commands are constructed from two kinds of element: 1. Conditions that MUST be true-any failure is treated as a failure of the update/load/boot 2. Directives that MUST be executed. The lists of commands are logically structured into sequences of zero or more conditions followed by zero or more directives. The *logical* structure is described by the following CDDL: Command_Sequence = { conditions => [ * Condition], directives => [ * Directive] } This introduces significant complexity in the parser, however, so the structure is flattened to make parsing simpler: SUIT_Command_Sequence = [ + (SUIT_Condition/SUIT_Directive) ] Each condition and directive is composed of: 1. A command code identifier 2. An argument block Argument blocks are defined for each type of command. Many conditions and directives apply to a given component, and these generally grouped together. Therefore, a special command to set the current component index is provided with a matching command to set the current dependency index. This index is a numeric index into the component ID tables defined at the beginning of the document. For the purpose of setting the index, the two component ID tables are considered to be concatenated together. Moran, et al. Expires January 9, 2020 [Page 23] Internet-Draft Firmware Manifest Format July 2019 To facilitate optional conditions, a special directive is provided. It runs several new lists of conditions/directives, one after another, that are contained as an argument to the directive. By default, it assumes that a failure of a condition should not indicate a failure of the update/boot, but a parameter is provided to override this behaviour. 7.11. SUIT_Condition Conditions are used to define mandatory properties of a system in order for an update to be applied. They can be pre-conditions or post-conditons of any directive or series of directives, depending on where they are placed in the list. Conditions include: +----------------+-------------------+----------------------------+ | Condition Code | Condition Name | Argument Type | +----------------+-------------------+----------------------------+ | 1 | Vendor Identifier | nil | | | | | | 2 | Class Identifier | nil | | | | | | 3 | Image Match | nil | | | | | | 4 | Use Before | Unsigned Integer timestamp | | | | | | 5 | Component Offset | Unsigned Integer | | | | | | 24 | Device Identifier | nil | | | | | | 25 | Image Not Match | nil | | | | | | 26 | Minimum Battery | Unsigned Integer | | | | | | 27 | Update Authorised | Integer | | | | | | 28 | Version | List of Integers | | | | | | nint | Custom Condition | bstr | +----------------+-------------------+----------------------------+ Each condition MUST report a success code on completion. If a condition reports failure, then the current sequence of commands MUST terminate. If a recipient encounters an unknown Condition Code, it MUST report a failure. Positive Condition numbers are reserved for IANA registration. Negative numbers are reserved for proprietary, application-specific directives. Moran, et al. Expires January 9, 2020 [Page 24] Internet-Draft Firmware Manifest Format July 2019 7.11.1. Identifier Conditions There are three identifier-based conditions: suit-condition-vendor- identifier, suit-condition-class-identifier, and suit-condition- device-identifier. Each of these conditions match a RFC 4122 [RFC4122] UUID that MUST have already been set as a parameter. The installing device MUST match the specified UUID in order to consider the manifest valid. These identifiers MAY be scoped by component. The recipient uses the ID parameter that has already been set using the Set Parameters directive. If no ID has been set, this condition fails. suit-condition-class-identifier and suit-condition-vendor- identifier are REQUIRED to implement. suit-condition-device- identifier is OPTIONAL to implement. 7.11.2. suit-condition-image-match Verify that the current component matches the digest parameter for the current component. The digest is verified against the digest specified in the Component's parameters list. If no digest is specified, the condition fails. suit-condition-image-match is REQUIRED to implement. 7.11.3. suit-condition-image-not-match Verify that the current component does not match the supplied digest. If no digest is specified, then the digest is compared against the digest specified in the Components list. If no digest is specified and the component is not present in the Components list, the condition fails. suit-condition-image-not-match is OPTIONAL to implement. 7.11.4. suit-condition-use-before Verify that the current time is BEFORE the specified time. suit- condition-use-before is used to specify the last time at which an update should be installed. One argument is required, encoded as a POSIX timestamp, that is seconds after 1970-01-01 00:00:00. Timestamp conditions MUST be evaluated in 64 bits, regardless of encoded CBOR size. suit-condition-use-before is OPTIONAL to implement. 7.11.5. suit-condition-minimum-battery suit-condition-minimum-battery provides a mechanism to test a device's battery level before installing an update. This condition is for use in primary-cell applications, where the battery is only ever discharged. For batteries that are charged, suit-directive-wait Moran, et al. Expires January 9, 2020 [Page 25] Internet-Draft Firmware Manifest Format July 2019 is more appropriate, since it defines a "wait" until the battery level is sufficient to install the update. suit-condition-minimum- battery is specified in mWh. suit-condition-minimum-battery is OPTIONAL to implement. 7.11.6. suit-condition-update-authorised Request Authorisation from the application and fail if not authorised. This can allow a user to decline an update. Argument is an integer priority level. Priorities are application defined. suit- condition-update-authorised is OPTIONAL to implement. 7.11.7. suit-condition-version suit-condition-version allows comparing versions of firmware. Verifying image digests is preferred to version checks because digests are more precise. The image can be compared as: - Greater - Greater or Equal - Equal - Lesser or Equal - Lesser Versions are encoded as a CBOR list of integers. Comparisons are done on each integer in sequence. Comparison stops after all integers in the list defined by the manifest have been consumed OR after a non-equal match has occured. For example, if the manifest defines a comparison, "Equal [1]", then this will match all version sequences starting with 1. If a manifest defines both "Greater or Equal [1,0]" and "Lesser [1,10]", then it will match versions 1.0.x up to, but not including 1.10. The following CDDL describes SUIT_Condition_Version_Argument Moran, et al. Expires January 9, 2020 [Page 26] Internet-Draft Firmware Manifest Format July 2019 SUIT_Condition_Version_Argument = [ suit-condition-version-comparison: SUIT_Condition_Version_Comparison_Types, suit-condition-version-comparison: SUIT_Condition_Version_Comparison_Value ] SUIT_Condition_Version_Comparison_Types /= SUIT_Condition_Version_Comparison_Greater SUIT_Condition_Version_Comparison_Types /= SUIT_Condition_Version_Comparison_Greater_Equal SUIT_Condition_Version_Comparison_Types /= SUIT_Condition_Version_Comparison_Equal SUIT_Condition_Version_Comparison_Types /= SUIT_Condition_Version_Comparison_Lesser_Equal SUIT_Condition_Version_Comparison_Types /= SUIT_Condition_Version_Comparison_Lesser SUIT_Condition_Version_Comparison_Greater = 1 SUIT_Condition_Version_Comparison_Greater_Equal = 2 SUIT_Condition_Version_Comparison_Equal = 3 SUIT_Condition_Version_Comparison_Lesser_Equal = 4 SUIT_Condition_Version_Comparison_Lesser = 5 SUIT_Condition_Version_Comparison_Value = [+int] While the exact encoding of versions is application-defined, semantic versions map conveniently. For example, - 1.2.3 = [1,2,3] - 1.2-rc3 = [1,2,-1,3] - 1.2-beta = [1,2,-2] - 1.2-alpha = [1,2,-3] - 1.2-alpha4 = [1,2,-3,4] suit-condition-version is OPTIONAL to implement. 7.11.8. SUIT_Condition_Custom SUIT_Condition_Custom describes any proprietary, application specific condition. This is encoded as a negative integer, chosen by the firmware developer, and a bstr that encodes the parameters passed to the system that evaluates the condition matching that integer. SUIT_Condition_Custom is OPTIONAL to implement. 7.11.9. Identifiers Many conditions use identifiers to determine whether a manifest matches a given recipient or not. These identifiers are defined to be RFC 4122 [RFC4122] UUIDs. These UUIDs are explicitly NOT human- readable. They are for machine-based matching only. Moran, et al. Expires January 9, 2020 [Page 27] Internet-Draft Firmware Manifest Format July 2019 A device may match any number of UUIDs for vendor or class identifier. This may be relevant to physical or software modules. For example, a device that has an OS and one or more applications might list one Vendor ID for the OS and one or more additional Vendor IDs for the applications. This device might also have a Class ID that must be matched for the OS and one or more Class IDs for the applications. A more complete example: A device has the following physical components: 1. A host MCU 2. A WiFi module This same device has three software modules: 1. An operating system 2. A WiFi module interface driver 3. An application Suppose that the WiFi module's firmware has a proprietary update mechanism and doesn't support manifest processing. This device can report four class IDs: 1. hardware model/revision 2. OS 3. WiFi module model/revision 4. Application This allows the OS, WiFi module, and application to be updated independently. To combat possible incompatibilities, the OS class ID can be changed each time the OS has a change to its API. This approach allows a vendor to target, for example, all devices with a particular WiFi module with an update, which is a very powerful mechanism, particularly when used for security updates. 7.11.9.1. Creating UUIDs: UUIDs MUST be created according to RFC 4122 [RFC4122]. UUIDs SHOULD use versions 3, 4, or 5, as described in RFC4122. Versions 1 and 2 do not provide a tangible benefit over version 4 for this application. The RECOMMENDED method to create a vendor ID is: Vendor ID = UUID5(DNS_PREFIX, vendor domain name) The RECOMMENDED method to create a class ID is: Class ID = UUID5(Vendor ID, Class-Specific-Information) Moran, et al. Expires January 9, 2020 [Page 28] Internet-Draft Firmware Manifest Format July 2019 Class-specific information is composed of a variety of data, for example: - Model number - Hardware revision - Bootloader version (for immutable bootloaders) 7.11.10. SUIT_Condition CDDL The following CDDL describes SUIT_Condition: SUIT_Condition //= (suit-condition-vendor-identifier, nil) SUIT_Condition //= (suit-condition-class-identifier, nil) SUIT_Condition //= (suit-condition-device-identifier, nil) SUIT_Condition //= (suit-condition-image-match, nil) SUIT_Condition //= (suit-condition-image-not-match, nil) SUIT_Condition //= (suit-condition-use-before, uint) SUIT_Condition //= (suit-condition-minimum-battery, uint) SUIT_Condition //= (suit-condition-update-authorised, int) SUIT_Condition //= (suit-condition-version, SUIT_Condition_Version_Argument) SUIT_Condition //= (suit-condition-component-offset, uint) SUIT_Condition //= (suit-condition-custom, bstr) SUIT_Condition_Version_Argument = [ suit-condition-version-comparison: SUIT_Condition_Version_Comparison_Types, suit-condition-version-comparison: SUIT_Condition_Version_Comparison_Value ] SUIT_Condition_Version_Comparison_Types /= suit-condition-version-comparison-greater SUIT_Condition_Version_Comparison_Types /= suit-condition-version-comparison-greater-equal SUIT_Condition_Version_Comparison_Types /= suit-condition-version-comparison-equal SUIT_Condition_Version_Comparison_Types /= suit-condition-version-comparison-lesser-equal SUIT_Condition_Version_Comparison_Types /= suit-condition-version-comparison-lesser SUIT_Condition_Version_Comparison_Value = [+int] 7.12. SUIT_Directive Directives are used to define the behaviour of the recipient. Directives include: Moran, et al. Expires January 9, 2020 [Page 29] Internet-Draft Firmware Manifest Format July 2019 +----------------+----------------------+ | Directive Code | Directive Name | +----------------+----------------------+ | 12 | Set Component Index | | | | | 13 | Set Dependency Index | | | | | 14 | Abort | | | | | 15 | Try Each | | | | | 16 | Reserved | | | | | 17 | Reserved | | | | | 18 | Process Dependency | | | | | 19 | Set Parameters | | | | | 20 | Override Parameters | | | | | 21 | Fetch | | | | | 22 | Copy | | | | | 23 | Run | | | | | 29 | Wait | | | | | 30 | Run Sequence | | | | | 31 | Run with Arguments | | | | | 32 | Swap | +----------------+----------------------+ When a Recipient executes a Directive, it MUST report a success code. If the Directive reports failure, then the current Command Sequence MUST terminate. 7.12.1. suit-directive-set-component-index Set Component Index defines the component to which successive directives and conditions will apply. The supplied argument MUST be either a boolean or an unsigned integer index into the concatenation of suit-components and suit-dependency-components. If the following directives apply to ALL components, then the boolean value "True" is used instead of an index. True does not apply to dependency Moran, et al. Expires January 9, 2020 [Page 30] Internet-Draft Firmware Manifest Format July 2019 components. If the following directives apply to NO components, then the boolean value "False" is used. When suit-directive-set- dependency-index is used, suit-directive-set-component-index = False is implied. When suit-directive-set-component-index is used, suit- directive-set-dependency-index = False is implied. The following CDDL describes the argument to suit-directive-set- component-index. SUIT_Directive_Set_Component_Index_Argument = uint/bool 7.12.2. suit-directive-set-dependency-index Set Dependency Index defines the manifest to which successive directives and conditions will apply. The supplied argument MUST be either a boolean or an unsigned integer index into the dependencies. If the following directives apply to ALL dependencies, then the boolean value "True" is used instead of an index. If the following directives apply to NO dependencies, then the boolean value "False" is used. When suit-directive-set-component-index is used, suit- directive-set-dependency-index = False is implied. When suit- directive-set-dependency-index is used, suit-directive-set-component- index = False is implied. Typical operations that require suit-directive-set-dependency-index include setting a source URI, invoking "Fetch," or invoking "Process Dependency" for an individual dependency. The following CDDL describes the argument to suit-directive-set- dependency-index. SUIT_Directive_Set_Manifest_Index_Argument = uint/bool 7.12.3. suit-directive-abort Unconditionally fail. This operation is typically used in conjunction with suit-directive-try-each. 7.12.4. suit-directive-run-sequence To enable conditional commands, and to allow several strictly ordered sequences to be executed out-of-order, suit-directive-run-sequence allows the manifest processor to execute its argument as a SUIT_Command_Sequence. The argument must be wrapped in a bstr. When a sequence is executed, any failure of a condition causes immediate termination of the sequence. Moran, et al. Expires January 9, 2020 [Page 31] Internet-Draft Firmware Manifest Format July 2019 The following CDDL describes the SUIT_Run_Sequence argument. SUIT_Directive_Run_Sequence_Argument = bstr .cbor SUIT_Command_Sequence When suit-directive-run-sequence completes, it forwards the last status code that occurred in the sequence. If the Coerce on Condition Failure parameter is true, then suit-directive-run-sequence only fails when a directive in the argument sequence fails. SUIT_Parameter_Coerce_Condition_Failure defaults to False when suit- directive-run-sequence begins. Its value is discarded when suit- directive-run-sequence terminates. 7.12.5. suit-directive-try-each This command runs several suit-directive-run-sequence one after another, in a strict order. Use this command to implement a "try/ catch-try/catch" sequence. Manifest processors MAY implement this command. SUIT_Parameter_Coerce_Condition_Failure is initialised to True at the beginning of each sequence. If one sequence aborts due to a condition failure, the next is started. If no sequence completes without condition failure, then suit-directive-try-each returns an error. If a particular application calls for all sequences to fail and still continue, then an empty sequence (nil) can be added to the Try Each Argument. The following CDDL describes the SUIT_Try_Each argument. SUIT_Directive_Try_Each_Argument = [ + bstr .cbor SUIT_Command_Sequence, nil / bstr .cbor SUIT_Command_Sequence ] 7.12.6. suit-directive-process-dependency Execute the commands in the common section of the current dependency, followed by the commands in the equivalent section of the current dependency. For example, if the current section is "fetch payload," this will execute "common" in the current dependency, then "fetch payload" in the current dependency. Once this is complete, the command following suit-directive-process-dependency will be processed. If the current dependency is False, this directive has no effect. If the current dependency is True, then this directive applies to all Moran, et al. Expires January 9, 2020 [Page 32] Internet-Draft Firmware Manifest Format July 2019 dependencies. If the current section is "common," this directive MUST have no effect. When SUIT_Process_Dependency completes, it forwards the last status code that occurred in the dependency. The argument to suit-directive-process-dependency is defined in the following CDDL. SUIT_Directive_Process_Dependency_Argument = nil 7.12.7. suit-directive-set-parameters suit-directive-set-parameters allows the manifest to configure behaviour of future directives by changing parameters that are read by those directives. When dependencies are used, suit-directive-set- parameters also allows a manifest to modify the behaviour of its dependencies. Available parameters are defined in Section 7.5. If a parameter is already set, suit-directive-set-parameters will skip setting the parameter to its argument. This provides the core of the override mechanism, allowing dependent manifests to change the behaviour of a manifest. The argument to suit-directive-set-parameters is defined in the following CDDL. SUIT_Directive_Set_Parameters_Argument = {+ SUIT_Parameters} N.B.: A directive code is reserved for an optimisation: a way to set a parameter to the contents of another parameter, optionally with another component ID. 7.12.8. suit-directive-override-parameters suit-directive-override-parameters replaces any listed parameters that are already set with the values that are provided in its argument. This allows a manifest to prevent replacement of critical parameters. Available parameters are defined in Section 7.5. The argument to suit-directive-override-parameters is defined in the following CDDL. SUIT_Directive_Override_Parameters_Argument = {+ SUIT_Parameters} Moran, et al. Expires January 9, 2020 [Page 33] Internet-Draft Firmware Manifest Format July 2019 7.12.9. suit-directive-fetch suit-directive-fetch instructs the manifest processor to obtain one or more manifests or payloads, as specified by the manifest index and component index, respectively. suit-directive-fetch can target one or more manifests and one or more payloads. suit-directive-fetch retrieves each component and each manifest listed in component-index and manifest-index, respectively. If component-index or manifest-index is True, instead of an integer, then all current manifest components/manifests are fetched. The current manifest's dependent-components are not automatically fetched. In order to pre-fetch these, they MUST be specified in a component-index integer. suit-directive-fetch typically takes no arguments unless one is needed to modify fetch behaviour. If an argument is needed, it must be wrapped in a bstr. suit-directive-fetch reads the URI or URI List parameter to find the source of the fetch it performs. The behaviour of suit-directive-fetch can be modified by setting one or more of SUIT_Parameter_Encryption_Info, SUIT_Parameter_Compression_Info, SUIT_Parameter_Unpack_Info. These three parameters each activate and configure a processing step that can be applied to the data that is transferred during suit-directive- fetch. The argument to suit-directive-fetch is defined in the following CDDL. SUIT_Directive_Fetch_Argument = nil/bstr 7.12.10. suit-directive-copy suit-directive-copy instructs the manifest processor to obtain one or more payloads, as specified by the component index. suit-directive- copy retrieves each component listed in component-index, respectively. If component-index is True, instead of an integer, then all current manifest components are copied. The current manifest's dependent-components are not automatically copied. In order to copy these, they MUST be specified in a component-index integer. The behaviour of suit-directive-copy can be modified by setting one or more of SUIT_Parameter_Encryption_Info, SUIT_Parameter_Compression_Info, SUIT_Parameter_Unpack_Info. These Moran, et al. Expires January 9, 2020 [Page 34] Internet-Draft Firmware Manifest Format July 2019 three parameters each activate and configure a processing step that can be applied to the data that is transferred during suit-directive- copy. *N.B.* Fetch and Copy are very similar. Merging them into one command may be appropriate. suit-directive-copy reads its source from SUIT_Parameter_Source_Component. The argument to suit-directive-copy is defined in the following CDDL. SUIT_Directive_Copy_Argument = nil 7.12.11. suit-directive-swap suit-directive-swap instructs the manifest processor to move the source to the destination and the destination to the source simultaneously. Swap has nearly identical semantics to suit- directive-copy except that suit-directive-swap replaces the source with the current contents of the destination in an application- defined way. If SUIT_Parameter_Compression_Info or SUIT_Parameter_Encryption_Info are present, they must be handled in a symmetric way, so that the source is decompressed into the destination and the destination is compressed into the source. The source is decrypted into the destination and the destination is encrypted into the source. suit-directive-swap is OPTIONAL to implement. 7.12.12. suit-directive-run suit-directive-run directs the manifest processor to transfer execution to the current Component Index. When this is invoked, the manifest processor MAY be unloaded and execution continues in the Component Index. Arguments provided to Run are forwarded to the executable code located in Component Index, in an application- specific way. For example, this could form the Linux Kernel Command Line if booting a linux device. If the executable code at Component Index is constructed in such a way that it does not unload the manifest processor, then the manifest processor may resume execution after the executable completes. This allows the manifest processor to invoke suitable helpers and to verify them with image conditions. The argument to suit-directive-run is defined in the following CDDL. SUIT_Directive_Run_Argument = nil/bstr Moran, et al. Expires January 9, 2020 [Page 35] Internet-Draft Firmware Manifest Format July 2019 7.12.13. suit-directive-wait suit-directive-wait directs the manifest processor to pause until a specified event occurs. Some possible events include: 1. Authorisation 2. External Power 3. Network availability 4. Other Device Firmware Version 5. Time 6. Time of Day 7. Day of Week The following CDDL defines the encoding of these events. SUIT_Wait_Events //= (suit-wait-event-authorisation => int) SUIT_Wait_Events //= (suit-wait-event-power => int) SUIT_Wait_Events //= (suit-wait-event-network => int) SUIT_Wait_Events //= (suit-wait-event-other-device-version => SUIT_Wait_Event_Argument_Other_Device_Version) SUIT_Wait_Events //= (suit-wait-event-time => uint); Timestamp SUIT_Wait_Events //= (suit-wait-event-time-of-day => uint); Time of Day (seconds since 00:00:00) SUIT_Wait_Events //= (suit-wait-event-day-of-week => uint); Days since Sunday SUIT_Wait_Event_Argument_Authorisation = int ; priority SUIT_Wait_Event_Argument_Power = int ; Power Level SUIT_Wait_Event_Argument_Network = int ; Network State SUIT_Wait_Event_Argument_Other_Device_Version = [ other-device: bstr, other-device-version: [+int] ] SUIT_Wait_Event_Argument_Time = uint ; Timestamp SUIT_Wait_Event_Argument_Time_Of_Day = uint ; Time of Day (seconds since 00:00:00) SUIT_Wait_Event_Argument_Day_Of_Week = uint ; Days since Sunday Moran, et al. Expires January 9, 2020 [Page 36] Internet-Draft Firmware Manifest Format July 2019 7.12.14. SUIT_Directive CDDL The following CDDL describes SUIT_Directive: Moran, et al. Expires January 9, 2020 [Page 37] Internet-Draft Firmware Manifest Format July 2019 SUIT_Directive //= (suit-directive-set-component-index, uint/bool) SUIT_Directive //= (suit-directive-set-dependency-index, uint/bool) SUIT_Directive //= (suit-directive-run-sequence, bstr .cbor SUIT_Command_Sequence) SUIT_Directive //= (suit-directive-try-each, SUIT_Directive_Try_Each_Argument) SUIT_Directive //= (suit-directive-process-dependency, nil) SUIT_Directive //= (suit-directive-set-parameters, {+ SUIT_Parameters}) SUIT_Directive //= (suit-directive-override-parameters, {+ SUIT_Parameters}) SUIT_Directive //= (suit-directive-fetch, nil) SUIT_Directive //= (suit-directive-copy, nil) SUIT_Directive //= (suit-directive-run, nil) SUIT_Directive //= (suit-directive-wait, { + SUIT_Wait_Events }) SUIT_Directive //= (suit-directive-run-with-arguments, bstr) SUIT_Directive_Try_Each_Argument = [ + bstr .cbor SUIT_Command_Sequence, nil / bstr .cbor SUIT_Command_Sequence ] SUIT_Wait_Events //= (suit-wait-event-authorisation => int) SUIT_Wait_Events //= (suit-wait-event-power => int) SUIT_Wait_Events //= (suit-wait-event-network => int) SUIT_Wait_Events //= (suit-wait-event-other-device-version => SUIT_Wait_Event_Argument_Other_Device_Version) SUIT_Wait_Events //= (suit-wait-event-time => uint); Timestamp SUIT_Wait_Events //= (suit-wait-event-time-of-day => uint); Time of Day (seconds since 00:00:00) SUIT_Wait_Events //= (suit-wait-event-day-of-week => uint); Days since Sunday SUIT_Wait_Event_Argument_Authorisation = int ; priority SUIT_Wait_Event_Argument_Power = int ; Power Level SUIT_Wait_Event_Argument_Network = int ; Network State SUIT_Wait_Event_Argument_Other_Device_Version = [ other-device: bstr, other-device-version: [+int] ] SUIT_Wait_Event_Argument_Time = uint ; Timestamp SUIT_Wait_Event_Argument_Time_Of_Day = uint ; Time of Day (seconds since 00:00:00) SUIT_Wait_Event_Argument_Day_Of_Week = uint ; Days since Sunday Moran, et al. Expires January 9, 2020 [Page 38] Internet-Draft Firmware Manifest Format July 2019 8. Dependency processing Dependencies need careful handling on constrained systems. A dependency tree that is too deep can cause recursive handling to overflow stack space. Systems that parse all dependencies into an object tree can easily fill up available memory. Too many dependencies can overrun available storage space. The dependency handling system in this document is designed to address as many of these problems as possible. Dependencies MAY be addressed in one of three ways: 1. Iterate by component 2. Iterate by manifest 3. Out-of-order Because each manifest has a list of components and a list of components defined by its dependencies, it is possible for the manifest processor to handle one component at a time, traversing the manifest tree once for each listed component. This, however consumes significant processing power. Alternatively, it is possible for a device with sufficient memory to accumulate all parameters for all listed component IDs. This will naturally consume more memory, but it allows the device to process the manifests in a single pass. It is expected that the simplest and most power sensitive devices will use option 2, with a fixed maximum number of components. Advanced devices may make use of the Strict Order parameter and enable parallel processing of some segments, or it may reorder some segments. To perform parallel processing, once the Strict Order parameter is set to False, the device may fork a process for each command until the Strict Order parameter is returned to True or the command sequence ends. Then, it joins all forked processes before continuing processing of commands. To perform out-of-order processing, a similar approach is used, except the device consumes all commands after the Strict Order parameter is set to False, then it sorts these commands into its preferred order, invokes them all, then continues processing. Moran, et al. Expires January 9, 2020 [Page 39] Internet-Draft Firmware Manifest Format July 2019 9. Access Control Lists To manage permissions in the manifest, there are three models that can be used. First, the simplest model requires that all manifests are authenticated by a single trusted key. This mode has the advantage that only a root manifest needs to be authenticated, since all of its dependencies have digests included in the root manifest. This simplest model can be extended by adding key delegation without much increase in complexity. A second model requires an ACL to be presented to the device, authenticated by a trusted party or stored on the device. This ACL grants access rights for specific component IDs or component ID prefixes to the listed identities or identity groups. Any identity may verify an image digest, but fetching into or fetching from a component ID requires approval from the ACL. A third model allows a device to provide even more fine-grained controls: The ACL lists the component ID or component ID prefix that an identity may use, and also lists the commands that the identity may use in combination with that component ID. 10. SUIT digest container RFC 8152 [RFC8152] provides containers for signature, MAC, and encryption, but no basic digest container. The container needed for a digest requires a type identifier and a container for the raw digest data. Some forms of digest may require additional parameters. These can be added following the digest. This structure is described by the following CDDL. The algorithms listed are sufficient for verifying integrity of Firmware Updates as of this writing, however this may change over time. Moran, et al. Expires January 9, 2020 [Page 40] Internet-Draft Firmware Manifest Format July 2019 SUIT_Digest = [ suit-digest-algorithm-id : $suit-digest-algorithm-ids, suit-digest-bytes : bytes, ? suit-digest-parameters : any ] digest-algorithm-ids /= algorithm-id-sha224 digest-algorithm-ids /= algorithm-id-sha256 digest-algorithm-ids /= algorithm-id-sha384 digest-algorithm-ids /= algorithm-id-sha512 digest-algorithm-ids /= algorithm-id-sha3-224 digest-algorithm-ids /= algorithm-id-sha3-256 digest-algorithm-ids /= algorithm-id-sha3-384 digest-algorithm-ids /= algorithm-id-sha3-512 algorithm-id-sha224 = 1 algorithm-id-sha256 = 2 algorithm-id-sha384 = 3 algorithm-id-sha512 = 4 algorithm-id-sha3-224 = 5 algorithm-id-sha3-256 = 6 algorithm-id-sha3-384 = 7 algorithm-id-sha3-512 = 8 11. Creating conditional sequences For some use cases, it is important to provide a sequence that can fail without terminating an update. For example, a dual-image XIP MCU may require an update that can be placed at one of two offsets. This has two implications, first, the digest of each offset will be different. Second, the image fetched for each offset will have a different URI. Conditional sequences allow this to be resolved in a simple way. The following JSON representation of a manifest demonstrates how this would be represented. It assumes that the bootloader and manifest processor take care of A/B switching and that the manifest is not aware of this distinction. { "structure-version" : 1, "sequence-number" : 7, "common" :{ "components" : [ [b'0'] ], "common-sequence" : [ { Moran, et al. Expires January 9, 2020 [Page 41] Internet-Draft Firmware Manifest Format July 2019 "directive-set-var" : { "size": 32567 }, }, { "try-each" : [ [ {"condition-component-offset" : ""}, { "directive-set-var": { "digest" : "" } } ], [ {"condition-component-offset" : ""}, { "directive-set-var": { "digest" : "" } } ], [{ "abort" : null }] ] } ] } "fetch" : [ { "try-each" : [ [ {"condition-component-offset" : ""}, { "directive-set-var": { "uri" : "" } } ], [ {"condition-component-offset" : ""}, { "directive-set-var": { "uri" : "" } } ], [{ "directive-abort" : null }] ] Moran, et al. Expires January 9, 2020 [Page 42] Internet-Draft Firmware Manifest Format July 2019 }, "fetch" : null ] } 12. Full CDDL In order to create a valid SUIT Manifest document the structure of the corresponding CBOR message MUST adhere to the following CDDL data definition. SUIT_Outer_Wrapper = { suit-authentication-wrapper => bstr .cbor SUIT_Authentication_Wrapper / nil, suit-manifest => bstr .cbor SUIT_Manifest, suit-dependency-resolution => bstr .cbor SUIT_Command_Sequence, suit-payload-fetch => bstr .cbor SUIT_Command_Sequence, suit-install => bstr .cbor SUIT_Command_Sequence, suit-text => bstr .cbor SUIT_Text_Map, suit-coswid => bstr .cbor concise-software-identity } suit-authentication-wrapper = 1 suit-manifest = 2 suit-dependency-resolution = 7 suit-payload-fetch = 8 suit-install = 9 suit-text = 13 suit-coswid = 14 SUIT_Authentication_Wrapper = [ * ( COSE_Mac_Tagged / COSE_Sign_Tagged / COSE_Mac0_Tagged / COSE_Sign1_Tagged)] COSE_Mac_Tagged = any COSE_Sign_Tagged = any COSE_Mac0_Tagged = any COSE_Sign1_Tagged = any COSE_Encrypt_Tagged = any COSE_Encrypt0_Tagged = any SUIT_Digest = [ suit-digest-algorithm-id : $suit-digest-algorithm-ids, suit-digest-bytes : bytes, ? suit-digest-parameters : any ] Moran, et al. Expires January 9, 2020 [Page 43] Internet-Draft Firmware Manifest Format July 2019 ; Named Information Hash Algorithm Identifiers suit-digest-algorithm-ids /= algorithm-id-sha256 suit-digest-algorithm-ids /= algorithm-id-sha256-128 suit-digest-algorithm-ids /= algorithm-id-sha256-120 suit-digest-algorithm-ids /= algorithm-id-sha256-96 suit-digest-algorithm-ids /= algorithm-id-sha256-64 suit-digest-algorithm-ids /= algorithm-id-sha256-32 suit-digest-algorithm-ids /= algorithm-id-sha384 suit-digest-algorithm-ids /= algorithm-id-sha512 suit-digest-algorithm-ids /= algorithm-id-sha3-224 suit-digest-algorithm-ids /= algorithm-id-sha3-256 suit-digest-algorithm-ids /= algorithm-id-sha3-384 suit-digest-algorithm-ids /= algorithm-id-sha3-512 SUIT_Manifest = { suit-manifest-version => 1, suit-manifest-sequence-number => uint, ? suit-dependencies => [ + SUIT_Dependency ], ? suit-components => [ + SUIT_Component ], ? suit-dependency-components => [ + SUIT_Component_Reference ], ? suit-common => bstr .cbor SUIT_Command_Sequence, ? suit-dependency-resolution => SUIT_Digest / bstr .cbor SUIT_Command_Sequence, ? suit-payload-fetch => SUIT_Digest / bstr .cbor SUIT_Command_Sequence, ? suit-install => SUIT_Digest / bstr .cbor SUIT_Command_Sequence ? suit-validate => bstr .cbor SUIT_Command_Sequence ? suit-load => bstr .cbor SUIT_Command_Sequence ? suit-run => bstr .cbor SUIT_Command_Sequence ? suit-text-info => SUIT_Digest / bstr .cbor SUIT_Text_Map ? suit-coswid => SUIT_Digest / bstr .cbor concise-software-identity } suit-manifest-version = 1 suit-manifest-sequence-number = 2 suit-dependencies = 3 suit-components = 4 suit-dependency-components = 5 suit-common = 6 suit-dependency-resolution = 7 suit-payload-fetch = 8 suit-install = 9 suit-validate = 10 suit-load = 11 suit-run = 12 suit-text-info = 13 suit-coswid = 14 concise-software-identity = any Moran, et al. Expires January 9, 2020 [Page 44] Internet-Draft Firmware Manifest Format July 2019 SUIT_Dependency = { suit-dependency-digest => SUIT_Digest, suit-dependency-prefix => SUIT_Component_Identifier, } suit-dependency-digest = 1 suit-dependency-prefix = 2 SUIT_Component_Identifier = [* bstr] SUIT_Component = { suit-component-identifier => SUIT_Component_Identifier, ? suit-component-size => uint, ? suit-component-digest => SUIT_Digest, } suit-component-identifier = 1 suit-component-size = 2 suit-component-digest = 3 SUIT_Component_Reference = { suit-component-identifier => SUIT_Component_Identifier, suit-component-dependency-index => uint } suit-component-dependency-index = 2 SUIT_Command_Sequence = [ + { SUIT_Condition // SUIT_Directive // SUIT_Command_Custom} ] SUIT_Command_Custom = (nint => bstr) SUIT_Condition //= (SUIT_Condition_Vendor_Identifier => RFC4122_UUID) ; SUIT_Condition_Vendor_Identifier SUIT_Condition //= (2 => RFC4122_UUID) ; SUIT_Condition_Class_Identifier SUIT_Condition //= (3 => RFC4122_UUID) ; SUIT_Condition_Device_Identifier SUIT_Condition //= (4 => SUIT_Digest) ; SUIT_Condition_Image_Match SUIT_Condition //= (5 => SUIT_Digest) ; SUIT_Condition_Image_Not_Match SUIT_Condition //= (6 => uint) ; SUIT_Condition_Use_Before SUIT_Condition //= (7 => uint) ; SUIT_Condition_Minimum_Battery SUIT_Condition //= (8 => int) ; SUIT_Condition_Update_Authorised SUIT_Condition //= (9 => SUIT_Condition_Version_Argument) ; SUIT_Condition_Version SUIT_Condition //= (10 => uint) ; SUIT_Condition_Component_Offset SUIT_Condition //= (nint => bstr) ; SUIT_Condition_Custom SUIT_Condition_Vendor_Identifier = 1 RFC4122_UUID = bstr .size 16 SUIT_Condition_Version_Argument = [ suit-condition-version-comparison: SUIT_Condition_Version_Comparison_Types, Moran, et al. Expires January 9, 2020 [Page 45] Internet-Draft Firmware Manifest Format July 2019 suit-condition-version-comparison: SUIT_Condition_Version_Comparison_Value ] SUIT_Condition_Version_Comparison_Types /= SUIT_Condition_Version_Comparison_Greater SUIT_Condition_Version_Comparison_Types /= SUIT_Condition_Version_Comparison_Greater_Equal SUIT_Condition_Version_Comparison_Types /= SUIT_Condition_Version_Comparison_Equal SUIT_Condition_Version_Comparison_Types /= SUIT_Condition_Version_Comparison_Lesser_Equal SUIT_Condition_Version_Comparison_Types /= SUIT_Condition_Version_Comparison_Lesser SUIT_Condition_Version_Comparison_Greater = 1 SUIT_Condition_Version_Comparison_Greater_Equal = 2 SUIT_Condition_Version_Comparison_Equal = 3 SUIT_Condition_Version_Comparison_Lesser_Equal = 4 SUIT_Condition_Version_Comparison_Lesser = 5 SUIT_Condition_Version_Comparison_Value = [+int] SUIT_Directive //= (11 => uint/bool) ; SUIT_Directive_Set_Component_Index SUIT_Directive //= (12 => uint/bool) ; SUIT_Directive_Set_Manifest_Index SUIT_Directive //= (13 => bstr .cbor SUIT_Command_Sequence) ; SUIT_Directive_Run_Sequence SUIT_Directive //= (14 => bstr .cbor SUIT_Command_Sequence) ; SUIT_Directive_Run_Sequence_Conditional SUIT_Directive //= (15 => nil) ; SUIT_Directive_Process_Dependency SUIT_Directive //= (16 => {+ SUIT_Parameters}) ; SUIT_Directive_Set_Parameters SUIT_Directive //= (19 => {+ SUIT_Parameters}) ; SUIT_Directive_Override_Parameters SUIT_Directive //= (20 => nil/bstr) ; SUIT_Directive_Fetch SUIT_Directive //= (21 => nil/bstr) ; SUIT_Directive_Copy SUIT_Directive //= (22 => nil/bstr) ; SUIT_Directive_Run SUIT_Directive //= (23 => { + SUIT_Wait_Events }) ; SUIT_Directive_Wait SUIT_Wait_Events //= (1 => SUIT_Wait_Event_Argument_Authorisation) SUIT_Wait_Events //= (2 => SUIT_Wait_Event_Argument_Power) SUIT_Wait_Events //= (3 => SUIT_Wait_Event_Argument_Network) SUIT_Wait_Events //= (4 => SUIT_Wait_Event_Argument_Other_Device_Version) SUIT_Wait_Events //= (5 => SUIT_Wait_Event_Argument_Time) SUIT_Wait_Events //= (6 => SUIT_Wait_Event_Argument_Time_Of_Day) SUIT_Wait_Events //= (7 => SUIT_Wait_Event_Argument_Day_Of_Week) SUIT_Wait_Event_Argument_Authorisation = int ; priority SUIT_Wait_Event_Argument_Power = int ; Power Level SUIT_Wait_Event_Argument_Network = int ; Network State SUIT_Wait_Event_Argument_Other_Device_Version = [ other-device: bstr, other-device-version: [+int] ] SUIT_Wait_Event_Argument_Time = uint ; Timestamp SUIT_Wait_Event_Argument_Time_Of_Day = uint ; Time of Day (seconds since 00:00:00) SUIT_Wait_Event_Argument_Day_Of_Week = uint ; Days since Sunday Moran, et al. Expires January 9, 2020 [Page 46] Internet-Draft Firmware Manifest Format July 2019 SUIT_Parameters //= (1 => bool) ; SUIT_Parameter_Strict_Order SUIT_Parameters //= (2 => bool) ; SUIT_Parameter_Coerce_Condition_Failure SUIT_Parameters //= (3 => bstr) ; SUIT_Parameter_Vendor_ID SUIT_Parameters //= (4 => bstr) ; SUIT_Parameter_Class_ID SUIT_Parameters //= (5 => bstr) ; SUIT_Parameter_Device_ID SUIT_Parameters //= (6 => bstr .cbor SUIT_URI_List) ; SUIT_Parameter_URI_List SUIT_Parameters //= (7 => bstr .cbor SUIT_Encryption_Info) ; SUIT_Parameter_Encryption_Info SUIT_Parameters //= (8 => bstr .cbor SUIT_Compression_Info) ; SUIT_Parameter_Compression_Info SUIT_Parameters //= (9 => bstr .cbor SUIT_Unpack_Info) ; SUIT_Parameter_Unpack_Info SUIT_Parameters //= (10 => bstr .cbor SUIT_Component_Identifier) ; SUIT_Parameter_Source_Component SUIT_Parameters //= (11 => bstr .cbor SUIT_Digest) ; SUIT_Parameter_Image_Digest SUIT_Parameters //= (12 => uint) ; SUIT_Parameter_Image_Size SUIT_Parameters //= (nint => int/bool/bstr) ; SUIT_Parameter_Custom SUIT_URI_List = [ + [priority: int, uri: tstr] ] SUIT_Encryption_Info = COSE_Encrypt_Tagged/COSE_Encrypt0_Tagged SUIT_Compression_Info = { suit-compression-algorithm => SUIT_Compression_Algorithms ? suit-compression-parameters => bstr } suit-compression-algorithm = 1 suit-compression-parameters = 2 SUIT_Compression_Algorithms /= SUIT_Compression_Algorithm_gzip SUIT_Compression_Algorithms /= SUIT_Compression_Algorithm_bzip2 SUIT_Compression_Algorithms /= SUIT_Compression_Algorithm_lz4 SUIT_Compression_Algorithms /= SUIT_Compression_Algorithm_lzma SUIT_Compression_Algorithm_gzip = 1 SUIT_Compression_Algorithm_bzip2 = 2 SUIT_Compression_Algorithm_deflate = 3 SUIT_Compression_Algorithm_lz4 = 4 SUIT_Compression_Algorithm_lzma = 7 SUIT_Unpack_Info = { suit-unpack-algorithm => SUIT_Unpack_Algorithms ? suit-unpack-parameters => bstr } suit-unpack-algorithm = 1 suit-unpack-parameters = 2 SUIT_Unpack_Algorithms /= SUIT_Unpack_Algorithm_Delta SUIT_Unpack_Algorithms /= SUIT_Unpack_Algorithm_Hex SUIT_Unpack_Algorithms /= SUIT_Unpack_Algorithm_Elf SUIT_Unpack_Algorithm_Delta = 1 SUIT_Unpack_Algorithm_Hex = 2 Moran, et al. Expires January 9, 2020 [Page 47] Internet-Draft Firmware Manifest Format July 2019 SUIT_Unpack_Algorithm_Elf = 3 SUIT_Text_Map = {int => tstr} 13. Examples The following examples demonstrate a small subset of the functionality of the manifest. However, despite this, even a simple manifest processor can execute most of these manifests. None of these examples include authentication. This is provided via RFC 8152 [RFC8152], and is omitted for clarity. 13.1. Example 0: Secure boot only. The following JSON shows the intended behaviour of the manifest. { "structure-version": 1, "sequence-number": 1, "run-image": [ { "directive-set-component": 0 }, { "condition-image": null }, { "directive-run": null } ], "common": { "common-sequence": [ { "directive-set-var": { "digest": "00112233445566778899aabbccddeeff" "0123456789abcdeffedcba9876543210", "size": 34768 } } ], "components": [ [ "Flash", 78848 ] ] } } Converted into the SUIT manifest, this produces: Moran, et al. Expires January 9, 2020 [Page 48] Internet-Draft Firmware Manifest Format July 2019 { / auth object / 1 : None / manifest / 3 : h'a40101020103583ca2024c818245466c6173684300340104' h'582a8213a20b582000112233445566778899aabbccddeeff' h'0123456789abcdeffedcba98765432100c1987d00c47860c' h'0003f617f6' \ { / structure-version / 1 : 1 / sequence-number / 2 : 1 / common / 3 : h'a2024c818245466c6173684300340104582a8213a20b58' h'2000112233445566778899aabbccddeeff0123456789ab' h'cdeffedcba98765432100c1987d0' \ { / components / 2 : h'818245466c61736843003401' \ [ [h'466c617368', h'003401'], ], / common / 4 : h'8213a20b582000112233445566778899aabbccddee' h'ff0123456789abcdeffedcba98765432100c1987d0' \ [ / set-vars / 19, { / digest / 11 :h'00112233445566778899aabbccddeeff01' h'23456789abcdeffedcba9876543210', / size / 12 : 34768 }, ], }, / run-image / 12 : h'860c0003f617f6' \ [ / set-component-index / 12, 0, / condition-image / 3, None, / run / 23, None, ], } } Total size of outer wrapper without COSE authentication object: 83 Outer: a201f603584da40101020103583ca2024c818245466c6173684300340104582a8213a20b 582000112233445566778899aabbccddeeff0123456789abcdeffedcba98765432100c19 87d00c47860c0003f617f6 13.2. Example 1: Simultaneous download and installation of payload. The following JSON shows the intended behaviour of the manifest. Moran, et al. Expires January 9, 2020 [Page 49] Internet-Draft Firmware Manifest Format July 2019 { "structure-version": 1, "sequence-number": 2, "apply-image": [ { "directive-set-component": 0 }, { "directive-set-var": { "uri": "http://example.com/file.bin" } }, { "directive-fetch": null } ], "common": { "common-sequence": [ { "directive-set-var": { "digest": "00112233445566778899aabbccddeeff" "0123456789abcdeffedcba9876543210", "size": 34768 } } ], "components": [ [ "Flash", 78848 ] ] } } Converted into the SUIT manifest, this produces: Moran, et al. Expires January 9, 2020 [Page 50] Internet-Draft Firmware Manifest Format July 2019 { / auth object / 1 : None / manifest / 3 : h'a40101020203583ca2024c818245466c6173684300340104' h'582a8213a20b582000112233445566778899aabbccddeeff' h'0123456789abcdeffedcba98765432100c1987d009582586' h'0c0013a106781b687474703a2f2f6578616d706c652e636f' h'6d2f66696c652e62696e15f6' \ { / structure-version / 1 : 1 / sequence-number / 2 : 2 / common / 3 : h'a2024c818245466c6173684300340104582a8213a20b58' h'2000112233445566778899aabbccddeeff0123456789ab' h'cdeffedcba98765432100c1987d0' \ { / components / 2 : h'818245466c61736843003401' \ [ [h'466c617368', h'003401'], ], / common / 4 : h'8213a20b582000112233445566778899aabbccddee' h'ff0123456789abcdeffedcba98765432100c1987d0' \ [ / set-vars / 19, { / digest / 11 :h'00112233445566778899aabbccddeeff01' h'23456789abcdeffedcba9876543210', / size / 12 : 34768 }, ], }, / apply-image / 9 : h'860c0013a106781b687474703a2f2f6578616d70' h'6c652e636f6d2f66696c652e62696e15f6' \ [ / set-component-index / 12, 0, / set-vars / 19, { / uri / 6 : http://example.com/file.bin }, / fetch / 21, None, ], } } Total size of outer wrapper without COSE authentication object: 114 Outer: a201f603586ca40101020203583ca2024c818245466c6173684300340104582a8213a20b 582000112233445566778899aabbccddeeff0123456789abcdeffedcba98765432100c19 87d0095825860c0013a106781b687474703a2f2f6578616d706c652e636f6d2f66696c65 2e62696e15f6 Moran, et al. Expires January 9, 2020 [Page 51] Internet-Draft Firmware Manifest Format July 2019 13.3. Example 2: Compatibility test, simultaneous download and installation, and secure boot. The following JSON shows the intended behaviour of the manifest. { "structure-version": 1, "sequence-number": 3, "common": { "common-sequence": [ { "directive-set-var": { "vendor-id": "fa6b4a53-d5ad-5fdf-be9d-e663e4d41ffe", "class-id": "1492af14-2569-5e48-bf42-9b2d51f2ab45", "digest": "00112233445566778899aabbccddeeff" "0123456789abcdeffedcba9876543210", "size": 34768 } }, { "condition-vendor-id": null }, { "condition-class-id": null } ], "components": [ [ "Flash", 78848 ] ] }, "apply-image": [ { "directive-set-component": 0 }, { "directive-set-var": { "uri": "http://example.com/file.bin" } }, { "directive-fetch": null } ], "run-image": [ { "directive-set-component": 0 }, { "condition-image": null }, { "directive-run": null } ] } Converted into the SUIT manifest, this produces: Moran, et al. Expires January 9, 2020 [Page 52] Internet-Draft Firmware Manifest Format July 2019 { / auth object / 1 : None / manifest / 3 : h'a501010203035864a2024c818245466c6173684300340104' h'58528613a40350fa6b4a53d5ad5fdfbe9de663e4d41ffe04' h'501492af1425695e48bf429b2d51f2ab450b582000112233' h'445566778899aabbccddeeff0123456789abcdeffedcba98' h'765432100c1987d001f602f6095825860c0013a106781b68' h'7474703a2f2f6578616d706c652e636f6d2f66696c652e62' h'696e15f60c47860c0003f617f6' \ { / structure-version / 1 : 1 / sequence-number / 2 : 3 / common / 3 : h'a2024c818245466c617368430034010458528613a40350' h'fa6b4a53d5ad5fdfbe9de663e4d41ffe04501492af1425' h'695e48bf429b2d51f2ab450b5820001122334455667788' h'99aabbccddeeff0123456789abcdeffedcba9876543210' h'0c1987d001f602f6' \ { / components / 2 : h'818245466c61736843003401' \ [ [h'466c617368', h'003401'], ], / common / 4 : h'8613a40350fa6b4a53d5ad5fdfbe9de663e4d41ffe' h'04501492af1425695e48bf429b2d51f2ab450b5820' h'00112233445566778899aabbccddeeff0123456789' h'abcdeffedcba98765432100c1987d001f602f6' \ [ / set-vars / 19, { / vendor-id / 3 : h'fa6b4a53d5ad5fdfbe9de663e4d41f' h'fe' / class-id / 4 : h'1492af1425695e48bf429b2d51f2ab45' / digest / 11 :h'00112233445566778899aabbccddeeff01' h'23456789abcdeffedcba9876543210', / size / 12 : 34768 }, / condition-vendor-id / 1, None, / condition-class-id / 2, None, ], }, / apply-image / 9 : h'860c0013a106781b687474703a2f2f6578616d70' h'6c652e636f6d2f66696c652e62696e15f6' \ [ / set-component-index / 12, 0, / set-vars / 19, { / uri / 6 : http://example.com/file.bin }, / fetch / 21, None, ], / run-image / 12 : h'860c0003f617f6' \ [ / set-component-index / 12, 0, / condition-image / 3, None, Moran, et al. Expires January 9, 2020 [Page 53] Internet-Draft Firmware Manifest Format July 2019 / run / 23, None, ], } } Total size of outer wrapper without COSE authentication object: 163 Outer: a201f603589da501010203035864a2024c818245466c617368430034010458528613a403 50fa6b4a53d5ad5fdfbe9de663e4d41ffe04501492af1425695e48bf429b2d51f2ab450b 582000112233445566778899aabbccddeeff0123456789abcdeffedcba98765432100c19 87d001f602f6095825860c0013a106781b687474703a2f2f6578616d706c652e636f6d2f 66696c652e62696e15f60c47860c0003f617f6 13.4. Example 3: Compatibility test, simultaneous download and installation, load from external storage, and secure boot. The following JSON shows the intended behaviour of the manifest. { "structure-version": 1, "sequence-number": 4, "common": { "common-sequence": [ { "directive-set-var": { "vendor-id": "fa6b4a53-d5ad-5fdf-be9d-e663e4d41ffe", "class-id": "1492af14-2569-5e48-bf42-9b2d51f2ab45" } }, { "directive-set-component": 0 }, { "directive-set-var": { "digest": "00112233445566778899aabbccddeeff" "0123456789abcdeffedcba9876543210", "size": 34768 } }, { "directive-set-component": 1 }, { "directive-set-var": { "digest": "00112233445566778899aabbccddeeff" "0123456789abcdeffedcba9876543210", "size": 34768 } Moran, et al. Expires January 9, 2020 [Page 54] Internet-Draft Firmware Manifest Format July 2019 }, { "condition-vendor-id": null }, { "condition-class-id": null } ], "components": [ [ "Flash", 78848 ], [ "RAM", 1024 ] ] }, "apply-image": [ { "directive-set-component": 0 }, { "directive-set-var": { "uri": "http://example.com/file.bin" } }, { "directive-fetch": null } ], "run-image": [ { "directive-set-component": 0 }, { "condition-image": null }, { "directive-set-component": 1 }, { "directive-set-var": { "source-index": 0 } }, { "directive-fetch": null }, { "condition-image": null }, { "directive-run": null } ] } Converted into the SUIT manifest, this produces: { / auth object / 1 : None / manifest / 3 : h'a50101020403589ba20254828245466c6173684300340182' h'4352414d4200040458818e13a20350fa6b4a53d5ad5fdfbe' h'9de663e4d41ffe04501492af1425695e48bf429b2d51f2ab' h'450c0013a20b582000112233445566778899aabbccddeeff' h'0123456789abcdeffedcba98765432100c1987d00c0113a2' Moran, et al. Expires January 9, 2020 [Page 55] Internet-Draft Firmware Manifest Format July 2019 h'0b582000112233445566778899aabbccddeeff0123456789' h'abcdeffedcba98765432100c1987d001f602f6095825860c' h'0013a106781b687474703a2f2f6578616d706c652e636f6d' h'2f66696c652e62696e15f60c518e0c0003f60c0113a10a00' h'15f603f617f6' \ { / structure-version / 1 : 1 / sequence-number / 2 : 4 / common / 3 : h'a20254828245466c61736843003401824352414d420004' h'0458818e13a20350fa6b4a53d5ad5fdfbe9de663e4d41f' h'fe04501492af1425695e48bf429b2d51f2ab450c0013a2' h'0b582000112233445566778899aabbccddeeff01234567' h'89abcdeffedcba98765432100c1987d00c0113a20b5820' h'00112233445566778899aabbccddeeff0123456789abcd' h'effedcba98765432100c1987d001f602f6' \ { / components / 2 : h'828245466c61736843003401824352414d4200' h'04' \ [ [h'466c617368', h'003401'], [h'52414d', h'0004'], ], / common / 4 : h'8e13a20350fa6b4a53d5ad5fdfbe9de663e4d41ffe' h'04501492af1425695e48bf429b2d51f2ab450c0013' h'a20b582000112233445566778899aabbccddeeff01' h'23456789abcdeffedcba98765432100c1987d00c01' h'13a20b582000112233445566778899aabbccddeeff' h'0123456789abcdeffedcba98765432100c1987d001' h'f602f6' \ [ / set-vars / 19, { / vendor-id / 3 : h'fa6b4a53d5ad5fdfbe9de663e4d41f' h'fe' / class-id / 4 : h'1492af1425695e48bf429b2d51f2ab45' }, / set-component-index / 12, 0, / set-vars / 19, { / digest / 11 :h'00112233445566778899aabbccddeeff01' h'23456789abcdeffedcba9876543210', / size / 12 : 34768 }, / set-component-index / 12, 1, / set-vars / 19, { / digest / 11 :h'00112233445566778899aabbccddeeff01' h'23456789abcdeffedcba9876543210', / size / 12 : 34768 }, / condition-vendor-id / 1, None, / condition-class-id / 2, None, ], Moran, et al. Expires January 9, 2020 [Page 56] Internet-Draft Firmware Manifest Format July 2019 }, / apply-image / 9 : h'860c0013a106781b687474703a2f2f6578616d70' h'6c652e636f6d2f66696c652e62696e15f6' \ [ / set-component-index / 12, 0, / set-vars / 19, { / uri / 6 : http://example.com/file.bin }, / fetch / 21, None, ], / run-image / 12 : h'8e0c0003f60c0113a10a0015f603f617f6' \ [ / set-component-index / 12, 0, / condition-image / 3, None, / set-component-index / 12, 1, / set-vars / 19, { / source-component / 10 : 0 }, / fetch / 21, None, / condition-image / 3, None, / run / 23, None, ], } } Total size of outer wrapper without COSE authentication object: 228 Outer: a201f60358dea50101020403589ba20254828245466c61736843003401824352414d4200 040458818e13a20350fa6b4a53d5ad5fdfbe9de663e4d41ffe04501492af1425695e48bf 429b2d51f2ab450c0013a20b582000112233445566778899aabbccddeeff0123456789ab cdeffedcba98765432100c1987d00c0113a20b582000112233445566778899aabbccddee ff0123456789abcdeffedcba98765432100c1987d001f602f6095825860c0013a106781b 687474703a2f2f6578616d706c652e636f6d2f66696c652e62696e15f60c518e0c0003f6 0c0113a10a0015f603f617f6 13.5. Example 4: Compatibility test, simultaneous download and installation, load and decompress from external storage, and secure boot. The following JSON shows the intended behaviour of the manifest. { "structure-version": 1, "sequence-number": 5, "common": { "common-sequence": [ { Moran, et al. Expires January 9, 2020 [Page 57] Internet-Draft Firmware Manifest Format July 2019 "directive-set-var": { "vendor-id": "fa6b4a53-d5ad-5fdf-be9d-e663e4d41ffe", "class-id": "1492af14-2569-5e48-bf42-9b2d51f2ab45" } }, { "directive-set-component": 0 }, { "directive-set-var": { "digest": "00112233445566778899aabbccddeeff" "0123456789abcdeffedcba9876543210", "size": 34768 } }, { "directive-set-component": 1 }, { "directive-set-var": { "digest": "0123456789abcdeffedcba9876543210" "00112233445566778899aabbccddeeff", "size": 34768 } }, { "condition-vendor-id": null }, { "condition-class-id": null } ], "components": [ [ "Flash", 78848 ], [ "RAM", 1024 ] ] }, "apply-image": [ { "directive-set-component": 0 }, { "directive-set-var": { "uri": "http://example.com/file.bin" } }, { "directive-fetch": null } ], "load-image": [ { "directive-set-component": 0 }, { "condition-image": null }, { "directive-set-component": 1 }, Moran, et al. Expires January 9, 2020 [Page 58] Internet-Draft Firmware Manifest Format July 2019 { "directive-set-var": { "source-index": 0, "compression-info": { "algorithm": "gzip" } } }, { "directive-copy": null } ], "run-image": [ { "condition-image": null }, { "directive-run": null } ] } Converted into the SUIT manifest, this produces: { / auth object / 1 : None / manifest / 3 : h'a60101020503589ba20254828245466c6173684300340182' h'4352414d4200040458818e13a20350fa6b4a53d5ad5fdfbe' h'9de663e4d41ffe04501492af1425695e48bf429b2d51f2ab' h'450c0013a20b582000112233445566778899aabbccddeeff' h'0123456789abcdeffedcba98765432100c1987d00c0113a2' h'0b58200123456789abcdeffedcba98765432100011223344' h'5566778899aabbccddeeff0c1987d001f602f6095825860c' h'0013a106781b687474703a2f2f6578616d706c652e636f6d' h'2f66696c652e62696e15f60b508a0c0003f60c0113a20841' h'f60a0016f60c458403f617f6' \ { / structure-version / 1 : 1 / sequence-number / 2 : 5 / common / 3 : h'a20254828245466c61736843003401824352414d420004' h'0458818e13a20350fa6b4a53d5ad5fdfbe9de663e4d41f' h'fe04501492af1425695e48bf429b2d51f2ab450c0013a2' h'0b582000112233445566778899aabbccddeeff01234567' h'89abcdeffedcba98765432100c1987d00c0113a20b5820' h'0123456789abcdeffedcba987654321000112233445566' h'778899aabbccddeeff0c1987d001f602f6' \ { / components / 2 : h'828245466c61736843003401824352414d4200' h'04' \ [ [h'466c617368', h'003401'], [h'52414d', h'0004'], ], / common / 4 : h'8e13a20350fa6b4a53d5ad5fdfbe9de663e4d41ffe' h'04501492af1425695e48bf429b2d51f2ab450c0013' Moran, et al. Expires January 9, 2020 [Page 59] Internet-Draft Firmware Manifest Format July 2019 h'a20b582000112233445566778899aabbccddeeff01' h'23456789abcdeffedcba98765432100c1987d00c01' h'13a20b58200123456789abcdeffedcba9876543210' h'00112233445566778899aabbccddeeff0c1987d001' h'f602f6' \ [ / set-vars / 19, { / vendor-id / 3 : h'fa6b4a53d5ad5fdfbe9de663e4d41f' h'fe' / class-id / 4 : h'1492af1425695e48bf429b2d51f2ab45' }, / set-component-index / 12, 0, / set-vars / 19, { / digest / 11 :h'00112233445566778899aabbccddeeff01' h'23456789abcdeffedcba9876543210', / size / 12 : 34768 }, / set-component-index / 12, 1, / set-vars / 19, { / digest / 11 :h'0123456789abcdeffedcba987654321000' h'112233445566778899aabbccddeeff', / size / 12 : 34768 }, / condition-vendor-id / 1, None, / condition-class-id / 2, None, ], }, / apply-image / 9 : h'860c0013a106781b687474703a2f2f6578616d70' h'6c652e636f6d2f66696c652e62696e15f6' \ [ / set-component-index / 12, 0, / set-vars / 19, { / uri / 6 : http://example.com/file.bin }, / fetch / 21, None, ], / load-image / 11 : h'8a0c0003f60c0113a20841f60a0016f6' \ [ / set-component-index / 12, 0, / condition-image / 3, None, / set-component-index / 12, 1, / set-vars / 19, { / unknown / 8 : h'f6' / source-component / 10 : 0 }, / copy / 22, None, ], / run-image / 12 : h'8403f617f6' \ [ / condition-image / 3, None, / run / 23, None, ], Moran, et al. Expires January 9, 2020 [Page 60] Internet-Draft Firmware Manifest Format July 2019 } } Total size of outer wrapper without COSE authentication object: 234 Outer: a201f60358e4a60101020503589ba20254828245466c61736843003401824352414d4200 040458818e13a20350fa6b4a53d5ad5fdfbe9de663e4d41ffe04501492af1425695e48bf 429b2d51f2ab450c0013a20b582000112233445566778899aabbccddeeff0123456789ab cdeffedcba98765432100c1987d00c0113a20b58200123456789abcdeffedcba98765432 1000112233445566778899aabbccddeeff0c1987d001f602f6095825860c0013a106781b 687474703a2f2f6578616d706c652e636f6d2f66696c652e62696e15f60b508a0c0003f6 0c0113a20841f60a0016f60c458403f617f6 13.6. Example 5: Compatibility test, download, installation, and secure boot. The following JSON shows the intended behaviour of the manifest. { "structure-version": 1, "sequence-number": 6, "common": { "common-sequence": [ { "directive-set-var": { "vendor-id": "fa6b4a53-d5ad-5fdf-be9d-e663e4d41ffe", "class-id": "1492af14-2569-5e48-bf42-9b2d51f2ab45" } }, { "directive-set-component": 0 }, { "directive-set-var": { "digest": "00112233445566778899aabbccddeeff" "0123456789abcdeffedcba9876543210", "size": 34768 } }, { "directive-set-component": 1 }, { "directive-set-var": { "digest": "0123456789abcdeffedcba9876543210" "00112233445566778899aabbccddeeff", "size": 34768 } }, Moran, et al. Expires January 9, 2020 [Page 61] Internet-Draft Firmware Manifest Format July 2019 { "condition-vendor-id": null }, { "condition-class-id": null } ], "components": [ [ "ext-Flash", 78848 ], [ "Flash", 1024 ] ] }, "apply-image": [ { "directive-set-component": 0 }, { "directive-set-var": { "uri": "http://example.com/file.bin" } }, { "directive-fetch": null } ], "load-image": [ { "directive-set-component": 1 }, { "condition-not-image": null }, { "directive-set-component": 0 }, { "condition-image": null }, { "directive-set-component": 1 }, { "directive-set-var": { "source-index": 0 } }, { "directive-fetch": null } ], "run-image": [ { "directive-set-component": 1 }, { "condition-image": null }, { "directive-run": null } ] } Converted into the SUIT manifest, this produces: { / auth object / 1 : None / manifest / 3 : h'a60101020603589ea202578282467b1b4595ab2143003401' Moran, et al. Expires January 9, 2020 [Page 62] Internet-Draft Firmware Manifest Format July 2019 h'8245466c6173684200040458818e13a20350fa6b4a53d5ad' h'5fdfbe9de663e4d41ffe04501492af1425695e48bf429b2d' h'51f2ab450c0013a20b582000112233445566778899aabbcc' h'ddeeff0123456789abcdeffedcba98765432100c1987d00c' h'0113a20b58200123456789abcdeffedcba98765432100011' h'2233445566778899aabbccddeeff0c1987d001f602f60958' h'25860c0013a106581b687474703a2f2f6578616d706c652e' h'636f6d2f66696c652e62696e15f60b528e0c011819f60c00' h'03f60c0113a10a0015f60c47860c0103f617f6' \ { / structure-version / 1 : 1 / sequence-number / 2 : 6 / common / 3 : h'a202578282467b1b4595ab21430034018245466c617368' h'4200040458818e13a20350fa6b4a53d5ad5fdfbe9de663' h'e4d41ffe04501492af1425695e48bf429b2d51f2ab450c' h'0013a20b582000112233445566778899aabbccddeeff01' h'23456789abcdeffedcba98765432100c1987d00c0113a2' h'0b58200123456789abcdeffedcba987654321000112233' h'445566778899aabbccddeeff0c1987d001f602f6' \ { / components / 2 : h'8282467b1b4595ab21430034018245466c6173' h'68420004' \ [ [h'7b1b4595ab21', h'003401'], [h'466c617368', h'0004'], ], / common / 4 : h'8e13a20350fa6b4a53d5ad5fdfbe9de663e4d41ffe' h'04501492af1425695e48bf429b2d51f2ab450c0013' h'a20b582000112233445566778899aabbccddeeff01' h'23456789abcdeffedcba98765432100c1987d00c01' h'13a20b58200123456789abcdeffedcba9876543210' h'00112233445566778899aabbccddeeff0c1987d001' h'f602f6' \ [ / set-vars / 19, { / vendor-id / 3 : h'fa6b4a53d5ad5fdfbe9de663e4d41f' h'fe' / class-id / 4 : h'1492af1425695e48bf429b2d51f2ab45' }, / set-component-index / 12, 0, / set-vars / 19, { / digest / 11 :h'00112233445566778899aabbccddeeff01' h'23456789abcdeffedcba9876543210', / size / 12 : 34768 }, / set-component-index / 12, 1, / set-vars / 19, { / digest / 11 :h'0123456789abcdeffedcba987654321000' h'112233445566778899aabbccddeeff', / size / 12 : 34768 Moran, et al. Expires January 9, 2020 [Page 63] Internet-Draft Firmware Manifest Format July 2019 }, / condition-vendor-id / 1, None, / condition-class-id / 2, None, ], }, / apply-image / 9 : h'860c0013a106581b687474703a2f2f6578616d70' h'6c652e636f6d2f66696c652e62696e15f6' \ [ / set-component-index / 12, 0, / set-vars / 19, { / uri / 6 : h'687474703a2f2f6578616d706c652e636f6d2f66' h'696c652e62696e' }, / fetch / 21, None, ], / load-image / 11 : h'8e0c011819f60c0003f60c0113a10a0015f6' \ [ / set-component-index / 12, 1, / condition-not-image / 25, None, / set-component-index / 12, 0, / condition-image / 3, None, / set-component-index / 12, 1, / set-vars / 19, { / source-component / 10 : 0 }, / fetch / 21, None, ], / run-image / 12 : h'860c0103f617f6' \ [ / set-component-index / 12, 1, / condition-image / 3, None, / run / 23, None, ], } } Total size of outer wrapper without COSE authentication object: 241 Outer: a201f60358eba60101020603589ea202578282467b1b4595ab21430034018245466c6173 684200040458818e13a20350fa6b4a53d5ad5fdfbe9de663e4d41ffe04501492af142569 5e48bf429b2d51f2ab450c0013a20b582000112233445566778899aabbccddeeff012345 6789abcdeffedcba98765432100c1987d00c0113a20b58200123456789abcdeffedcba98 7654321000112233445566778899aabbccddeeff0c1987d001f602f6095825860c0013a1 06581b687474703a2f2f6578616d706c652e636f6d2f66696c652e62696e15f60b528e0c 011819f60c0003f60c0113a10a0015f60c47860c0103f617f6 Moran, et al. Expires January 9, 2020 [Page 64] Internet-Draft Firmware Manifest Format July 2019 13.7. Example 6: Compatibility test, 2 images, simultaneous download and installation, and secure boot. The following JSON shows the intended behaviour of the manifest. { "structure-version": 1, "sequence-number": 7, "common": { "common-sequence": [ { "directive-set-var": { "vendor-id": "fa6b4a53-d5ad-5fdf-be9d-e663e4d41ffe", "class-id": "1492af14-2569-5e48-bf42-9b2d51f2ab45" } }, { "directive-set-component": 0 }, { "directive-set-var": { "digest": "00112233445566778899aabbccddeeff" "0123456789abcdeffedcba9876543210", "size": 34768 } }, { "directive-set-component": 1 }, { "directive-set-var": { "digest": "0123456789abcdeffedcba9876543210" "00112233445566778899aabbccddeeff", "size": 76834 } }, { "condition-vendor-id": null }, { "condition-class-id": null } ], "components": [ [ "Flash", 78848 ], [ "Flash", 132096 ] ] }, Moran, et al. Expires January 9, 2020 [Page 65] Internet-Draft Firmware Manifest Format July 2019 "apply-image": [ { "directive-set-component": 0 }, { "directive-set-var": { "uri": "http://example.com/file1.bin" } }, { "directive-set-component": 1 }, { "directive-set-var": { "uri": "http://example.com/file2.bin" } }, { "directive-set-component": true }, { "directive-fetch": null } ], "run-image": [ { "directive-set-component": true }, { "condition-image": null }, { "directive-set-component": 0 }, { "directive-run": null } ] } Converted into the SUIT manifest, this produces: { / auth object / 1 : None / manifest / 3 : h'a5010102070358a0a20257828245466c6173684300340182' h'45466c617368430004020458838e13a20350fa6b4a53d5ad' h'5fdfbe9de663e4d41ffe04501492af1425695e48bf429b2d' h'51f2ab450c0013a20b582000112233445566778899aabbcc' h'ddeeff0123456789abcdeffedcba98765432100c1987d00c' h'0113a20b58200123456789abcdeffedcba98765432100011' h'2233445566778899aabbccddeeff0c1a00012c2201f602f6' h'09584b8c0c0013a106781c687474703a2f2f6578616d706c' h'652e636f6d2f66696c65312e62696e0c0113a106781c6874' h'74703a2f2f6578616d706c652e636f6d2f66696c65322e62' h'696e0cf515f60c49880cf503f60c0017f6' \ { / structure-version / 1 : 1 / sequence-number / 2 : 7 / common / 3 : h'a20257828245466c617368430034018245466c61736843' h'0004020458838e13a20350fa6b4a53d5ad5fdfbe9de663' h'e4d41ffe04501492af1425695e48bf429b2d51f2ab450c' h'0013a20b582000112233445566778899aabbccddeeff01' h'23456789abcdeffedcba98765432100c1987d00c0113a2' h'0b58200123456789abcdeffedcba987654321000112233' Moran, et al. Expires January 9, 2020 [Page 66] Internet-Draft Firmware Manifest Format July 2019 h'445566778899aabbccddeeff0c1a00012c2201f602f6' \ { / components / 2 : h'828245466c617368430034018245466c617368' h'43000402' \ [ [h'466c617368', h'003401'], [h'466c617368', h'000402'], ], / common / 4 : h'8e13a20350fa6b4a53d5ad5fdfbe9de663e4d41ffe' h'04501492af1425695e48bf429b2d51f2ab450c0013' h'a20b582000112233445566778899aabbccddeeff01' h'23456789abcdeffedcba98765432100c1987d00c01' h'13a20b58200123456789abcdeffedcba9876543210' h'00112233445566778899aabbccddeeff0c1a00012c' h'2201f602f6' \ [ / set-vars / 19, { / vendor-id / 3 : h'fa6b4a53d5ad5fdfbe9de663e4d41f' h'fe' / class-id / 4 : h'1492af1425695e48bf429b2d51f2ab45' }, / set-component-index / 12, 0, / set-vars / 19, { / digest / 11 :h'00112233445566778899aabbccddeeff01' h'23456789abcdeffedcba9876543210', / size / 12 : 34768 }, / set-component-index / 12, 1, / set-vars / 19, { / digest / 11 :h'0123456789abcdeffedcba987654321000' h'112233445566778899aabbccddeeff', / size / 12 : 76834 }, / condition-vendor-id / 1, None, / condition-class-id / 2, None, ], }, / apply-image / 9 : h'8c0c0013a106781c687474703a2f2f6578616d70' h'6c652e636f6d2f66696c65312e62696e0c0113a1' h'06781c687474703a2f2f6578616d706c652e636f' h'6d2f66696c65322e62696e0cf515f6' \ [ / set-component-index / 12, 0, / set-vars / 19, { / uri / 6 : http://example.com/file1.bin }, / set-component-index / 12, 1, / set-vars / 19, { / uri / 6 : http://example.com/file2.bin }, Moran, et al. Expires January 9, 2020 [Page 67] Internet-Draft Firmware Manifest Format July 2019 / set-component-index / 12, True, / fetch / 21, None, ], / run-image / 12 : h'880cf503f60c0017f6' \ [ / set-component-index / 12, True, / condition-image / 3, None, / set-component-index / 12, 0, / run / 23, None, ], } } Total size of outer wrapper without COSE authentication object: 264 Outer: a201f603590101a5010102070358a0a20257828245466c617368430034018245466c6173 68430004020458838e13a20350fa6b4a53d5ad5fdfbe9de663e4d41ffe04501492af1425 695e48bf429b2d51f2ab450c0013a20b582000112233445566778899aabbccddeeff0123 456789abcdeffedcba98765432100c1987d00c0113a20b58200123456789abcdeffedcba 987654321000112233445566778899aabbccddeeff0c1a00012c2201f602f609584b8c0c 0013a106781c687474703a2f2f6578616d706c652e636f6d2f66696c65312e62696e0c01 13a106781c687474703a2f2f6578616d706c652e636f6d2f66696c65322e62696e0cf515 f60c49880cf503f60c0017f6 14. IANA Considerations Several registries will be required for: - standard Commands - standard Parameters - standard Algorithm identifiers - standard text values 15. Security Considerations This document is about a manifest format describing and protecting firmware images and as such it is part of a larger solution for offering a standardized way of delivering firmware updates to IoT devices. A more detailed discussion about security can be found in the architecture document [Architecture] and in [Information]. Moran, et al. Expires January 9, 2020 [Page 68] Internet-Draft Firmware Manifest Format July 2019 16. Mailing List Information The discussion list for this document is located at the e-mail address suit@ietf.org [1]. Information on the group and information on how to subscribe to the list is at https://www1.ietf.org/mailman/listinfo/suit [2] Archives of the list can be found at: https://www.ietf.org/mail- archive/web/suit/current/index.html [3] 17. Acknowledgements We would like to thank the following persons for their support in designing this mechanism: - Milosch Meriac - Geraint Luff - Dan Ros - John-Paul Stanford - Hugo Vincent - Carsten Bormann - Oeyvind Roenningstad - Frank Audun Kvamtroe - Krzysztof Chruściński - Andrzej Puzdrowski - Michael Richardson - David Brown - Emmanuel Baccelli 18. References 18.1. Normative References Moran, et al. Expires January 9, 2020 [Page 69] Internet-Draft Firmware Manifest Format July 2019 [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC4122] Leach, P., Mealling, M., and R. Salz, "A Universally Unique IDentifier (UUID) URN Namespace", RFC 4122, DOI 10.17487/RFC4122, July 2005, . [RFC8152] Schaad, J., "CBOR Object Signing and Encryption (COSE)", RFC 8152, DOI 10.17487/RFC8152, July 2017, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . 18.2. Informative References [Architecture] Moran, B., "A Firmware Update Architecture for Internet of Things Devices", January 2019, . [Information] Moran, B., "Firmware Updates for Internet of Things Devices - An Information Model for Manifests", January 2019, . [RFC6920] Farrell, S., Kutscher, D., Dannewitz, C., Ohlman, B., Keranen, A., and P. Hallam-Baker, "Naming Things with Hashes", RFC 6920, DOI 10.17487/RFC6920, April 2013, . 18.3. URIs [1] mailto:suit@ietf.org [2] https://www1.ietf.org/mailman/listinfo/suit [3] https://www.ietf.org/mail-archive/web/suit/current/index.html Moran, et al. Expires January 9, 2020 [Page 70] Internet-Draft Firmware Manifest Format July 2019 Authors' Addresses Brendan Moran Arm Limited EMail: Brendan.Moran@arm.com Hannes Tschofenig Arm Limited EMail: hannes.tschofenig@arm.com Henk Birkholz Fraunhofer SIT EMail: henk.birkholz@sit.fraunhofer.de Moran, et al. Expires January 9, 2020 [Page 71]