Network Working Group M. Wasserman Internet-Draft Painless Security Intended status: Standards Track F. Baker Expires: June 13, 2011 Cisco Systems December 10, 2010 IPv6-to-IPv6 Network Prefix Translation draft-mrw-nat66-02 Abstract This document describes a stateless, transport-agnostic IPv6-to-IPv6 Network Prefix Translation (NPTv6) function that provides the address independence benefit associated with IPv4-to-IPv4 NAT (NAT44), and in addition provides a 1:1 relationship between addresses in the "inside" and "outside" prefixes, preserving end to end reachability at the network layer. Requirements Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on June 13, 2011. Copyright Notice Copyright (c) 2010 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Wasserman & Baker Expires June 13, 2011 [Page 1] Internet-Draft NPTv6 December 2010 Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1. What is Address Independence? . . . . . . . . . . . . . . 4 1.2. NPTv6 Applicability . . . . . . . . . . . . . . . . . . . 6 2. NPTv6 Overview . . . . . . . . . . . . . . . . . . . . . . . . 7 2.1. NPTv6: the simplest case . . . . . . . . . . . . . . . . . 7 2.2. NPTv6 between peer networks . . . . . . . . . . . . . . . 8 2.3. NPTv6 redundnacy and load-sharing . . . . . . . . . . . . 9 2.4. NPTv6 multihoming . . . . . . . . . . . . . . . . . . . . 9 2.5. Mapping with No Per-Flow State . . . . . . . . . . . . . . 10 2.6. Checksum-Neutral Mapping . . . . . . . . . . . . . . . . . 10 3. NPTv6 Algorithmic Specification . . . . . . . . . . . . . . . 11 3.1. NPTv6 configuration calculations . . . . . . . . . . . . . 11 3.2. NPTv6 translation, internal network to external network . 11 3.3. NPTv6 translation, external network to internal network . 12 3.4. NPTv6 with a /48 or shorter prefix . . . . . . . . . . . . 12 3.5. NPTv6 with a /49 or longer prefix . . . . . . . . . . . . 12 3.6. /48 Prefix Mapping Example . . . . . . . . . . . . . . . . 13 3.7. Address Mapping for Longer Prefixes . . . . . . . . . . . 13 4. Implications of Network Address Translator Behavioral Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.1. Prefix Configuration and generation . . . . . . . . . . . 14 4.2. NAT Behavioral Requirements . . . . . . . . . . . . . . . 15 5. Implications for Applications . . . . . . . . . . . . . . . . 15 6. A Note on Port Mapping . . . . . . . . . . . . . . . . . . . . 16 7. Security Considerations . . . . . . . . . . . . . . . . . . . 16 8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 17 9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 17 10. Change Log . . . . . . . . . . . . . . . . . . . . . . . . . . 17 10.1. Changes Between draft-mrw-behave-nat66-00 and -01 . . . . 17 10.2. Changes between *behave-nat66-01 and -02 . . . . . . . . . 17 10.3. Changes between *behave-nat66-02 and *nat66-00 . . . . . . 18 10.4. Changes between *nat66-00 and *nat66-01 . . . . . . . . . 18 11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 19 11.1. Normative References . . . . . . . . . . . . . . . . . . . 19 11.2. Informative References . . . . . . . . . . . . . . . . . . 19 Appendix A. Why GSE? . . . . . . . . . . . . . . . . . . . . . . 20 Wasserman & Baker Expires June 13, 2011 [Page 2] Internet-Draft NPTv6 December 2010 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 22 Wasserman & Baker Expires June 13, 2011 [Page 3] Internet-Draft NPTv6 December 2010 1. Introduction This document describes a stateless IPv6-to-IPv6 Network Prefix Translation (NPTv6) function, designed to provide address independence to the edge network. It is transport-agnostic with respect to transports that don't checksum the IP header, such as SCTP or DCCP, and to transports that use the TCP/UDP pseudo-header and checksum [RFC1071]. This has several ramifications: o Any security benefit that NAT44 might offer is not present in NPTv6, necessitating the use of a firewall to obtain those benefits if desired. An example of such a firewall is described in [I-D.ietf-v6ops-cpe-simple-security]. o End to end reachability is preserved, although the address used "inside" the edge network differs from the address used "outside" the edge network. This has implications for application referrals and other uses of Internet layer addresses. o If there are multiple identically-configured prefix translators between two networks, there is no need for them to exchange dynamic state, as there is no dynamic state - the algorithmic translation will be identical across each of them. The network can therefore asymmetrically route, load-share, and fail-over among them without issue. o Since translation is 1:1 at the network layer, there is no need to modify port numbers or other transport parameters. 1.1. What is Address Independence? For the purposes of this document, IPv6 Address Independence consists of the following set of properties: From the perspective of the edge network: * The IPv6 addresses used inside the local network (for interfaces, access lists, and logs) do not need to be renumbered if the upstream network changes a site's external prefix. * The IPv6 addresses used inside the edge network (for interfaces, access lists, and logs) or within other upstream networks (such as when multihoming) do not need to be renumbered when a site adds, drops, or changes upstream networks. Wasserman & Baker Expires June 13, 2011 [Page 4] Internet-Draft NPTv6 December 2010 * It is not necessary for an administration to convince an upstream network to route its internal IPv6 prefixes, or for it to advertise prefixes derived from other upstream networks into it. * Unless it wants to optimize routing between multiple upstream networks in the process of multihoming, there is therefore no need for a BGP exchange with the upstream network. From the perspective of the upstream network: * IPv6 addresses used by the edge network are guaranteed to have a provider-allocated prefix, eliminating the need and concern for BCP 38 [RFC2827] ingress filtering and the advertisement of customer-specific prefixes. Thus, address independence has ramifications for the edge network, networks it directly connects with (especially its upstream networks), and for the Internet as a whole. The desire for address independence has been a primary driver for IPv4 NAT deployment in medium to large-sized enterprise networks, including NAT deployments in enterprises that have plenty of IPv4 provider-independent address space (from IPv4 "swamp space"). It has also been a driver for edge networks to become members of RIR communities, seeking to obtain BGP Autonomous System Numbers and provider-independent prefixes, and as a result has been one of the drivers of the explosion of the IPv4 route table. Service providers have stated that the lack of address independence from their customers has been a negative incentive to deployment, due to the impact of customer routing expected in their networks. The Local Network Protection [RFC4864] document discusses a related concept called "Address Autonomy" as a benefit of NAT44. [RFC4864] indicates that address autonomy can be achieved by the simultaneous use of global addresses on all nodes within a site that need external connectivity, and Unique Local Addresses (ULAs) [RFC4193] for all internal communication. However, this solution fails to meet the requirement for address independence, because if an ISP renumbering event occurs, all of the hosts, routers, DHCP servers, ACLs, firewalls and other internal systems that are configured with global addresses from the ISP will need to be renumbered before global connectivity is fully restored. The use of IPv6 Provider Independent (PI) addresses has also been suggested as a means to fulfill the address independence requirement. However, this solution requires that an enterprise qualify to receive a PI assignment and persuade their ISP to install specific routes for the enterprise's PI addresses. There are a number of practical Wasserman & Baker Expires June 13, 2011 [Page 5] Internet-Draft NPTv6 December 2010 issues with this approach, especially if there is a desire to route to a number of geographically and topologically diverse set of sites, which can sometimes involve coordinating with several ISPs to route portions of a single PI prefix. These problems have caused numerous enterprises with plenty of IPv4 swamp space to choose to use IPv4 NAT for part, or substantially all, of their internal network instead of using their provider-independent address space. 1.2. NPTv6 Applicability NPTv6 provides a simple and compelling solution to meet the Address Independence requirement in IPv6. The address independence benefit stems directly from the translation function of the network prefix translator. To avoid as many of the issues associated with NAT44 as possible, NPTv6 is defined to include a two-way, checksum-neutral, algorithmic translation function, and nothing else. NPTv6 does not include a port mapping function, and the defined address mapping mechanism is checksum-neutral. This avoids the need for a NPTv6 Translator to re-write transport layer headers, making it feasible to deploy new or improved transport layer protocols without upgrading NPTv6 Translators. Because NPTv6 does not involve re- writing transport-layer headers, NPTv6 will not interfere with encryption of the full IP payload in many cases. The default NPTv6 address mapping mechanism is purely algorithmic, so NPTv6 translators do not need to maintain per-node or per-connection state, allowing deployment of more robust and adaptive networks than can be deployed using NAT44. Since the default NPTv6 mapping can be performed in either direction, it does not interfere with inbound connection establishment, thus allowing internal nodes to participate in direct Peer-to-Peer applications without the application layer overhead one finds in many IPv4 Peer-to-Peer applications. Although NPTv6 compares favorably to NAT44 in several ways, it does not eliminate all of the architectural problems associated with IPv4 NAT, as described in [RFC2993]. NPTv6 involves modifying IP headers in transit, so it is not compatible with security mechanisms, such as the IPsec Authentication Header, that provide integrity protection for the IP header. NPTv6 may interfere with the use of application protocols that transmit IP addresses in the application-specific portion of the IP packet. These applications currently require application layer gateways (ALGs) to work correctly through NAT44 devices, and similar ALGs may be required for these applications to work through NPTv6 Translators. The use of separate internal and external prefixes creates complexity for DNS deployment, due the desire for internal nodes to communicate with other internal nodes using internal addresses, while external nodes need to obtain Wasserman & Baker Expires June 13, 2011 [Page 6] Internet-Draft NPTv6 December 2010 external addresses to communicate with the same nodes. This frequently results in the deployment of "split DNS", which may add complexity to network configuration. There are significant technical impacts associated with the deployment of any prefix translation mechanism, including NPTv6, and we strongly encourage anyone who is considering the implementation or deployment of NPTv6 to read [RFC4864], and to carefully consider the alternatives described in that document, some of which may cause fewer problems than NPTv6. 2. NPTv6 Overview NPTv6 may be implemented in an IPv6 router to map one IPv6 address prefix to another IPv6 prefix as each IPv6 packet transits the router. A router that implements a NPTv6 prefix translation function is referred to as an NPTv6 Translator. 2.1. NPTv6: the simplest case In its simplest form, a NPTv6 Translator interconnects two network links, one of which is an "internal" network link attached to a leaf network within a single administrative domain, and the other of which is an "external" network with connectivity to the global Internet. All of the hosts on the internal network will use addresses from a single, locally-routed prefix, and those addresses will be translated to/from addresses in a globally-routable prefix as IP packets transit the NPTv6 Translator. The lengths of these two prefixes will be functionally the same; if they differ, the longer of the two will limit the ability to use subnets in the shorter. External Network: Prefix = 2001:0DB8:0001:/48 -------------------------------------- | | +-------------+ | NPTv6 | | Translator | +-------------+ | | -------------------------------------- Internal Network: Prefix = FD01:0203:0405:/48 Figure 1: A simple translator Figure 1 shows a NPTv6 Translator attached to two networks. In this Wasserman & Baker Expires June 13, 2011 [Page 7] Internet-Draft NPTv6 December 2010 example, the internal network uses IPv6 Unique Local Addresses (ULAs) [RFC4193] to represent the internal IPv6 nodes, and the external network uses globally routable IPv6 addresses to represent the same nodes. When a NPTv6 Translator forwards packets in the "outbound" direction, from the internal network to the external network, NPTv6 overwrites the IPv6 source prefix (in the IPv6 header) with a corresponding external prefix. When packets are forwarded in the "inbound" direction, from the external network to the internal network, the IPv6 destination prefix is overwritten with a corresponding prefix internal prefix. Using the prefixes shown in the diagram above, as an IP packet passes through the NPTv6 Translator in the outbound direction, the source prefix (FD01:0203:0405:/48) will be overwritten with the external prefix (2001:0DB8:0001:/48). In an inbound packet, the destination prefix (2001:0DB8:0001:/48) will be overwritten with the internal prefix (FD01:0203:0405:/48). In both cases, it is the local IPv6 prefix that is overwritten; the remote IPv6 prefix remains unchanged. Nodes on the internal network are said to be "behind" the NPTv6 Translator. 2.2. NPTv6 between peer networks NPTv6 can also be used between two private networks. In these cases, both networks may use ULA prefixes, with each subnet in one network mapped into a corresponding subnet in the other network, and vice versa. Or, each network may use ULA prefixes for internal addressing, and global unicast addresses on the other network. Internal Prefix = FD01:4444:5555:/48 -------------------------------------- V | External Prefix V | 2001:0DB8:6666:/48 V +---------+ ^ V | NPTv6 | ^ V | Device | ^ V +---------+ ^ External Prefix | ^ 2001:0DB8:0001:/48 | ^ -------------------------------------- Internal Prefix = FD01:0203:0405:/48 Figure 2: Flow of Information in Translation Wasserman & Baker Expires June 13, 2011 [Page 8] Internet-Draft NPTv6 December 2010 2.3. NPTv6 redundnacy and load-sharing In some cases, more than one NPTv6 Translator may be attached to a network, as show in Figure 3. In such cases, NPTv6 Translators are configured with the same internal and external prefixes. Since there is only one translation, even though there are multiple translators, they map only one external address (prefix and IID) to the internal address. External Network: Prefix = 2001:0DB8:0001:/48 -------------------------------------- | | | | +-------------+ +-------------+ | NPTv6 | | NPTv6 | | Translator | | Translator | | #1 | | #2 | +-------------+ +-------------+ | | | | -------------------------------------- Internal Network: Prefix = FD01:0203:0405:/48 Figure 3: Parallel Translators 2.4. NPTv6 multihoming External Network #1: External Network #2: Prefix = 2001:0DB8:0001:/48 Prefix = 2001:0DB8:5555:/48 --------------------------- -------------------------- | | | | +-------------+ +-------------+ | NPTv6 | | NPTv6 | | Translator | | Translator | | #1 | | #2 | +-------------+ +-------------+ | | | | -------------------------------------- Internal Network: Prefix = FD01:0203:0405:/48 Figure 4: Parallel Translators with different upstream networks When multihoming, NPTv6 Translators are attached to an internal network, as show in Figure 4, but connected to different external networks. In such cases, NPTv6 Translators are configured with the same internal prefix, but different external prefixes. Since there Wasserman & Baker Expires June 13, 2011 [Page 9] Internet-Draft NPTv6 December 2010 are multiple translations, they map multiple external addresses (prefix and IID) to the common internal address. A system within the edge network is unable to determine which external address it is using. Multihoming in this sense has one negative feature as compared with multihoming with a provider-independent address; when routes change between NPTv6 Translators, since the upstream network changes, the prefix used in shifting sessions changes. This obviously causes them to fail. This is not expected to be a major real issue, however, in networks where routing is generally stable. 2.5. Mapping with No Per-Flow State When NPTv6 is used as described in this document, no per-node or per- flow state is maintained in the NPTv6 Translator. Both inbound and outbound packets are translated algorithmically, using only information found in the IPv6 header. Due to this property, NPTv6's two-way, algorithmic address mapping can support both outbound and inbound connection establishment without the need for state-priming or rendezvous mechanisms, or the maintenance of mapping state. This is a significant improvement over NAT44 devices, but it also has significant security implications which are described in the Security Considerations section. 2.6. Checksum-Neutral Mapping When a change is made to one of the IP header fields in the IPv6 pseudo-header checksum (such as one of the IP addresses), the checksum field in the transport layer header may become invalid. Fortunately, an incremental change in the area covered by the Internet standard checksum [RFC1071] will result in a well-defined change to the checksum value [RFC1624]. So, a checksum change caused by modifying part of the area covered by the checksum can be corrected by making a complementary change to a different 16-bit field covered by the same checksum. The NPTv6 mapping mechanisms described in this document are checksum- neutral, which means that they result in IP headers that will generate the same IPv6 pseudo-header checksum when the checksum is calculated using the standard Internet checksum algorithm [RFC1071]. Any changes that are made during translation of the IPv6 prefix are offset by changes to other parts of the IPv6 address. This results in transport layers that use the Internet checksum (such as TCP and UDP) calculating the same IPv6 pseudo header checksum for both the internal and external forms of the same packet, which avoids the need for the NPTv6 Translator to modify those transport layer headers to correct the checksum value. Wasserman & Baker Expires June 13, 2011 [Page 10] Internet-Draft NPTv6 December 2010 3. NPTv6 Algorithmic Specification The [RFC4291] IPv6 Address is reproduced for clarity in Figure 5. 0 15 16 31 32 47 48 63 64 79 80 95 96 111 112 127 +-------+-------+-------+-------+-------+-------+-------+-------+ | Routing Prefix |Subnet| Interface Identifier (IID) | +-------+-------+-------+-------+-------+-------+-------+-------+ Figure 5: Enumeration of the IPv6 Address [RFC4291] 3.1. NPTv6 configuration calculations When an NPTv6 Translation function is configured, it is configured with o one or more "internal" interfaces with their "internal" routing domain prefixes, and o one or more "external" interfaces with their "external" routing domain prefixes. In the simple case, there is one of each. If a single router provides NPTv6 translation services between a multiplicity of domains (as might be true when multihoming), each internal/external pair must be thought of as a separate NPTv6 Translator from the perspective of this specification. When an NPTv6 Translator is configured, the translation function first ensures that the internal and external prefixes are the same length, if necessary by extending the shorter of the two with zeroes. These two prefixes will be used in the prefix translation function described in Section 3.2 and Section 3.3. They are then zero-extended to /64, for the purposes of a calculation. The translation function calculates the ones-complement sum of the 16 bit words of the /64 external prefix and the /64 internal prefix. It then calculates the difference between these values: external minus internal. This value, called the "adjustment", is effectively constant for the lifetime of the NPTv6 Translator configuration, and used in per-packet processing. 3.2. NPTv6 translation, internal network to external network When a datagram passes through the NPTv6 Translator from an internal to an external network, its IPv6 Source Address is changed in two ways: Wasserman & Baker Expires June 13, 2011 [Page 11] Internet-Draft NPTv6 December 2010 o The internal prefix is overwritten with the external prefix, and o A 16-bit word of the address has the "adjustment" added to it using one's complement arithmetic. If the result is 0xFFFF, it is overwritten as zero. The choice of word is as specified in Section 3.4 or Section 3.5 as appropriate. 3.3. NPTv6 translation, external network to internal network When a datagram passes through the NPTv6 Translator from an internal to an external network, its IPv6 Destination Address is changed in two ways: o The external prefix is overwritten with the internal prefix, and o A 16-bit word of the address has the "adjustment" subtracted from it (bitwise inverted and added to it) it using one's complement arithmetic. If the result is 0xFFFF, it is overwritten as zero. The choice of word is as specified in Section 3.4 or Section 3.5 as appropriate. 3.4. NPTv6 with a /48 or shorter prefix When a NPTv6 Translator is configured with internal and external prefixes that are 48 bits in length (a /48) or shorter, the adjustment MUST be added to or subtracted from bits 48..63 of the address. This mapping results in no modification of the Interface Identifier (IID), which is held in the lower half of the IPv6 address, so it will not interfere with future protocols that may use unique IIDs for node identification. NPTv6 Translator implementations MUST implement the /48 mapping. 3.5. NPTv6 with a /49 or longer prefix When a NPTv6 Translator is configured with internal and external prefixes that are longer than 48 bits in length (such as a /52, /56, or /60), the adjustment must be added to or subtracted from one of the words in bits 64..79, 80..95, 96..111, or 112..127 of the address. While the choice of word is immaterial as long as it is consistent, for consistency's sake, these words MUST be inspected in that sequence, and the first that is not initially 0xFFFF chosen. NPTv6 Translator implementations SHOULD implement the mapping for longer prefixes. Wasserman & Baker Expires June 13, 2011 [Page 12] Internet-Draft NPTv6 December 2010 3.6. /48 Prefix Mapping Example For the network shown in Figure 1, the Internal Prefix is FD01:0203: 0405:/48, and the External Prefix is 2001:0DB8:0001:/48 If a node with internal address FD01:0203:0405:0001::1234 sends an outbound packet through the NPTv6 Translator, the resulting external address will be 2001:0DB8:0001:D550::1234. The resulting address is obtained by calculating the checksum of both the internal and external 48-bit prefixes, subtracting the internal prefix from the external prefix using one's complement arithmetic to calculate the "adjustment", and adding the adjustment to the 16-bit subnet field (in this case 0x0001). To show the work: The one's complement checksum of FD01:0203:0405 is 0xFCF5. The one's complement checksum of 2001:0DB8:0001 is 0xD245. Using one's complement math, 0xD245 - 0xFCF5 = 0xD54F. The subnet in the original packet is 0x0001. Using one's complement math, 0x0001 + 0xD54F = 0xD550. Since 0xD550 != 0xFFFF, it is not changed to 0x0000. So, the value 0xD550 is written in the 16-bit subnet area, resulting in a mapped external address of 2001:0DB8:0001:D550::1234. When a response packet is received, it will contain the destination address 2001:0DB8:0001:D550::0001, which will be mapped using the inverse mapping algorithm, back to FD01:0203:0405:0001::1234. In this case, the difference between the two prefixes will be calculated as follows: Using one's complement math, 0xFCF5 - 0xD245 = 0x2AB0. The subnet in the original packet = 0xD550. Using one's complement math, 0xD550 + 0x2AB0 = 0x0001. Since 0x0001 != 0xFFFF, it is not changed to 0x0000. So the value 0x0001 is written into the subnet field, and the internal value of the subnet field is properly restored. 3.7. Address Mapping for Longer Prefixes If the prefix being mapped is longer than 48 bits, the algorithm is slightly more complex. A common case will be that the internal and external prefixes are of different length. In such a case, the shorter prefix is zero-extended to the length of the longer as described in Section 3.1 for the purposes of overwriting the prefix. Then, they are both zero-extended to 64 bits to facilitate one's Wasserman & Baker Expires June 13, 2011 [Page 13] Internet-Draft NPTv6 December 2010 complement arithmetic. The "adjustment" is calculated using those 64 bit prefixes. For example if the internal prefix is a /48 ULA and the external prefix is a /56 provider-allocated prefix, the ULA becomes a /56 with zeros in bits 48..55. For purposes of one's complement arithmetic, they are then both zero-extended to 64 bits. A side-effect of this is that a subset of the subnets possible in the shorter prefix are untranslatable. While the security value of this is debatable, the administration may choose to use them for subnets that it knows need no external accessibility. We then find the first word in the IID that does not have the value 0xFFFF, trying bits 64..79, and then 80..95, 96..111, and finally 112..127. We perform the same calculation (with the same proof of correctness) as in Section 3.6, but applying it to that word. Although any 16-bit portion of an IPv6 IID could contain 0xFFFF, an IID of all-ones is a reserved anycast identifier that should not be used on the network [RFC2526]. If a NPTv6 Translator discovers a packet with an IID of all-zeros while performing address mapping, that packet MUST be dropped, and an ICMPv6 Parameter Problem error SHOULD be generated [RFC4443]. Note: this mechanism does involve modification of the IID; it may not be compatible with future mechanisms that use unique IIDs for node identification. 4. Implications of Network Address Translator Behavioral Requirements 4.1. Prefix Configuration and generation NPTv6 Translators MUST support manual configuration of internal and external prefixes, and MUST NOT place any restrictions on those prefixes except that they be valid IPv6 unicast prefixes as described in [RFC4291]. NPTv6 Translators that do not have a manually configured internal prefix SHOULD randomly generate a ULA prefix for the internal network and advertise that prefix in router advertisements. NPTv6 Translators with more than one internal interface SHOULD assign a (non-0xFFFF) subnet number to each link, and include the subnet number in router advertisements on the corresponding link. NPTv6 Translators that generate a ULA prefix MUST generate the prefix using a random number as described in RFC4291 [RFC4193], and SHOULD store the randomly generated prefix in non-volatile storage for continued use. Wasserman & Baker Expires June 13, 2011 [Page 14] Internet-Draft NPTv6 December 2010 4.2. NAT Behavioral Requirements NPTv6 Translators MUST support hairpinning behavior, as defined in the NAT Behavioral Requirements for UDP document [RFC4787]. This means that when a NPTv6 Translator receives a packet on the internal interface that has a destination address that matches the site's external prefix, it will translate the packet and forward it internally. This allows internal nodes to reach other internal nodes using their external, global addresses when necessary. Conceptually, the datagram leaves the domain (is translated as described in Section 3.2), and returns (is again translated as described in Section 3.3). As a result, the datagram exchange will be through the NPTv6 Translator in both directions for the lifetime of the session. The alternative would be to require the NPTv6 Translator to drop the datagram, forcing the sender to use the correct internal prefix for its peer. Performing only the external- to-internal translation results in the datagram being sent from the untranslated internal address of the source to the translated and therefore internal address of its peer, which would enable the session to bypass the NPTv6 Translator for future datagrams. It would also mean that the original sender would be unlikely to recognize the response when it arrived. Because NPTv6 does not perform port mapping and uses a one-to-one, reversible mapping algorithm, none of the other NAT behavioral requirements apply to NPTv6. 5. Implications for Applications The use of NPTv6 Transition technology makes a capability available to Applications (and the networks that contain them) that is not readily possible in a NAT44 network. This is the ability to position an externally-accessible application within the "internal" network. In an IPv4 network using NAT44, externally-accessible application must be positioned on systems with global addresses, forcing the edge network to obtain global address allocation; if the application can be in the translated routing domain, it automatically has an address in each of its upstream prefixes without the edge network obtaining such. However, there must be a means for the application to know what addresses are usable. Reasons include at least advertisement in DNS (which might be done statically if DNS is directly maintained by the administration, or from the end system if Dynamic DNS is in use). If referrals and other uses of network layer addressing do not use names, then the application needs a means to determine what addresses are relevant, whether from DNS or another means. Wasserman & Baker Expires June 13, 2011 [Page 15] Internet-Draft NPTv6 December 2010 The means of address discovery is not within the scope of this specification. 6. A Note on Port Mapping In addition to overwriting IP addresses when packets are forwarded, NAPT44 devices overwrite the source port number in outbound traffic, and the destination port number in inbound traffic. This mechanism is called "port mapping". The major benefit of port mapping is that it allows multiple computers to share a single IPv4 address. A large number of internal IPv4 addresses (typically from the 10.0.0.0/8 prefix) can be mapped into a single external, globally routable IPv4 address, with the local port number used to identify which internal node should receive each inbound packet. This address amplification feature should not be needed in IPv6. Since port mapping requires re-writing a portion of the transport layer header, it requires NAPT44 devices to be aware of all of the transport protocols that they forward, thus stifling the development of new and improved transport protocols and preventing the use of IPsec encryption. Modifying the transport layer header is incompatible with security mechanisms that encrypt the full IP payload, and restricts the NAPT44 to forwarding transport layers that use weak checksum algorithms that are easily recalculated in routers. Since there is significant detriment caused by modifying transport layer headers and very little, if any, benefit to the use of port mapping in IPv6, NPTv6 Translators that comply with this specification MUST NOT perform port mapping. 7. Security Considerations When NPTv6 is deployed using either of the two-way, algorithmic mappings defined in the document, it allows direct inbound connections to internal nodes. While this can be viewed as a benefit of NPTv6 vs. NAT44, it does open internal nodes to attacks that would be more difficult in a NAT44 network. Although this situation is not substantially worse, from a security standpoint, than running IPv6 with no NAT, some enterprises may assume that a NPTv6 Translator will offer similar protection to a NAT44 device. For this reason, it is RECOMMENDED that NPTv6 Translators also implement firewall functionality such as described in [I-D.ietf-v6ops-cpe-simple-security], with appropriate configuration options including turning it on or off. Wasserman & Baker Expires June 13, 2011 [Page 16] Internet-Draft NPTv6 December 2010 8. IANA Considerations This document has no IANA considerations. 9. Acknowledgements The checksum-neutral algorithmic address mapping described in this document is based on e-mail written by Iljtsch Van Beijnum. The following people provided advice or review comments that substantially improved this document: Jari Arrko, Iljtsch Van Beijnum, Remi Depres, Tony Hain, Ed Jankiewicz, Dave Thaler, Mark Townsley, and Steve Blake. This document was written using the xml2rfc tool described in RFC 2629 [RFC2629]. 10. Change Log 10.1. Changes Between draft-mrw-behave-nat66-00 and -01 There were several minor changes made between the *behave-nat66-00 and -01 versions of this draft: o Added Fred Baker as a co-author. o Minor mathematical corrections. o Added AH to paragraph on NAT security issues. o Added additional NAT topologies to overview (diagrams TBD). 10.2. Changes between *behave-nat66-01 and -02 There were further changes made between *behave-nat66-01 and -02: o Removed topology hiding mechanism. o Added diagrams. o Made minor updates based on mailing list feedback. o Added discussion of IPv6 SAF document. o Added applicability section. Wasserman & Baker Expires June 13, 2011 [Page 17] Internet-Draft NPTv6 December 2010 o Added discussion of Address Independence requirement. o Added hairpinning requirement and discussion of applicability of other NAT behavioral requirements. 10.3. Changes between *behave-nat66-02 and *nat66-00 There were further changes made between behave-nat66-02 and nat66-02: o Added mapping for prefixes longer than /48. o Change draft name to remove reference to the behave WG. o Resolved various open issues and fixed typos. 10.4. Changes between *nat66-00 and *nat66-01 o Change the acronym "NAT66" to "NPTv6", so people don't read "NAT" and MEGO. o Change the term used to refer to the function from "NAT66 device" to "NPTv6 Translator". It's not a "device" function, it's a function that is applied between two interfaces. Consider a router with two upstreams and two legs in the local network; it will not translate between the local legs, but will translate to and from each upstream, and be configured differently for each of the two ISPs. o Comment specifically on the security aspects. o Comment specifically on the application issues raised on this list. o Comment specifically on multihoming, load-sharing, and asymmetric routing. o Spell out the hairpinning requirement and its implications. o Spell out the service provider side of Address Independence. o 00 focuses on the edge's view o Detail the algorithm in a manner clearer to the implementor (I think) o Spell out the case for GSE-style DMZs between the edge and the transit network, which is about the implications for the global routing table. Wasserman & Baker Expires June 13, 2011 [Page 18] Internet-Draft NPTv6 December 2010 o Refer to xref target="I-D.ietf-v6ops-cpe-simple-security"/>. 11. References 11.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2526] Johnson, D. and S. Deering, "Reserved IPv6 Subnet Anycast Addresses", RFC 2526, March 1999. [RFC4193] Hinden, R. and B. Haberman, "Unique Local IPv6 Unicast Addresses", RFC 4193, October 2005. [RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 4291, February 2006. [RFC4443] Conta, A., Deering, S., and M. Gupta, "Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification", RFC 4443, March 2006. [RFC4787] Audet, F. and C. Jennings, "Network Address Translation (NAT) Behavioral Requirements for Unicast UDP", BCP 127, RFC 4787, January 2007. 11.2. Informative References [GSE] O'Dell, M., "GSE - An Alternate Addressing Architecture for IPv6", February 1997, . [I-D.ietf-v6ops-cpe-simple-security] Woodyatt, J., "Recommended Simple Security Capabilities in Customer Premises Equipment for Providing Residential IPv6 Internet Service", draft-ietf-v6ops-cpe-simple-security-16 (work in progress), October 2010. [RFC1071] Braden, R., Borman, D., Partridge, C., and W. Plummer, "Computing the Internet checksum", RFC 1071, September 1988. [RFC1624] Rijsinghani, A., "Computation of the Internet Checksum via Incremental Update", RFC 1624, May 1994. [RFC2629] Rose, M., "Writing I-Ds and RFCs using XML", RFC 2629, June 1999. Wasserman & Baker Expires June 13, 2011 [Page 19] Internet-Draft NPTv6 December 2010 [RFC2827] Ferguson, P. and D. Senie, "Network Ingress Filtering: Defeating Denial of Service Attacks which employ IP Source Address Spoofing", BCP 38, RFC 2827, May 2000. [RFC2993] Hain, T., "Architectural Implications of NAT", RFC 2993, November 2000. [RFC4864] Van de Velde, G., Hain, T., Droms, R., Carpenter, B., and E. Klein, "Local Network Protection for IPv6", RFC 4864, May 2007. Appendix A. Why GSE? For the purpose of this discussion, let us over-simplify the Internet's structure by distinguishing between two broad classes of networks: transit and edge. A "transit network", in this context, is a network that provides connectivity services to other networks. Its AS number may show up in a non-final position in BGP AS paths, or in the case of mobile and residential broadband networks, it may offer network services to smaller networks that can't justify RIR membership. An "edge network", in contrast, is any network that is not a transit network; it is the ultimate customer, and while it provides internal connectivity for its own use, it is in other respects is a consumer of transit services. In terms of routing, a network in the transit domain generally needs some way to make choices about how it routes to other networks; an edge network is generally quite satisfied with a simple default route. The [GSE] proposal, and as a result this proposal (which is similar to GSE in most respects and inspired by it), responds directly to current concerns in the RIR communities. Edge networks are used to an environment in IPv4 in which their addressing is disjoint from that of their upstream transit networks; it is either provider independent, or a network prefix translator makes their external address distinct from their internal address, and they like the distinction. In IPv6, there is a mantra that edge network addresses should be derived from their upstream, and if they have multiple upstreams, edge networks are expected to design their networks to use all of those prefixes equivalently. They see this as unnecessary and unwanted operational complexity, and are as a result pushing very hard in the RIR communities for provider independent addressing. Widespread use of provider independent addressing has a natural and perhaps unavoidable side-effect that is likely to be very expensive in the long term. It means that the routing table will enumerate the networks at the edge of the transit domain, the edge networks, rather than enumerating the transit domain. Per the CIDR Report, there are Wasserman & Baker Expires June 13, 2011 [Page 20] Internet-Draft NPTv6 December 2010 currently more than 36,000 Autonomous Systems being advertised in BGP, of which over 15,000 advertise only one prefix. There are in the neighborhood of 5000 AS's that show up in a non-final position in AS paths, and perhaps another 5000 networks whose AS numbers are terminal in more than one AS path. In other words, we have prefixes for some 36,000 transit and edge networks in the route table now, many of which arguably need an Autonomous System number only for multihoming. Current estimates suggest that we could easily see that be on the order of 10,000,000 within fifteen years. Tens of thousands of entries in the route table is very survivable; while our protocols and computers will likely do quite well with tens of millions of routes, the heat produced and power consumed by those routers, and the inevitable impact on the cost of those routers, is not a good outcome. To avoid having a massive and unscalable route table, we need to find a way that is politically acceptable and returns us to enumerating the transit domain, not the edge. There have been a number of proposals. As described, shim6 moves the complexity to the edge, and the edge is rebelling. Geographic addressing in essence forces ISPs to "own" geographic territory from a routing perspective, as otherwise there is no clue in the address as to what network a datagram should be delivered to in order to reach it. Metropolitan Addressing can imply regulatory authority, and even if it is implemented using internet exchange consortia, visits a great deal of complexity on the transit networks that directly serve the edge. The one that is likely to be most acceptable is any proposal that enables an edge network to be operationally independent of its upstreams, with no obligation to renumber when it adds, drops, or changes ISPs, and with no additional burden placed either on the ISP or the edge network as a result. From an application perspective, an additional operational requirement in the words of US NIST's Roadmap for the Smart Grid, is that "...the Network should enable an application in a particular domain to communicate with an application in any other domain in the information network, with proper management control over who and where applications can be interconnected." In other words, the structure of the network should allow for and enable appropriate access control, but the structure of the network should not inherently limit access. The GSE model, by statelessly translating the prefix between an edge network and its upstream transit network, accomplishes that with a minimum of fuss and bother. Stated in the simplest terms, it enables the edge network to behave as if it has a provider-independent prefix from a multihoming and renumbering perspective without the overhead Wasserman & Baker Expires June 13, 2011 [Page 21] Internet-Draft NPTv6 December 2010 of RIR membership or maintaining BGP connectivity, and it enables the transit networks to aggressively aggregate what are from their perspective provider-allocated customer prefixes, to maintain a rational-sized routing table. Authors' Addresses Margaret Wasserman Painless Security North Andover, MA 01845 USA Phone: +1 781 405 7464 Email: mrw@painless-security.com URI: http://www.painless-secuirty.com Fred Baker Cisco Systems Santa Barbara, California 93117 USA Phone: +1-408-526-4257 Email: fred@cisco.com Wasserman & Baker Expires June 13, 2011 [Page 22]