<?xml version="1.0" encoding="UTF-8"?>
<!-- edited with XMLSPY v5 rel. 3 U (http://www.xmlspy.com)
     by Daniel M Kohn (private) -->

<!DOCTYPE rfc SYSTEM "rfc2629.dtd" [
    <!ENTITY rfc2119 PUBLIC '' 
      'http://xml.resource.org/public/rfc/bibxml/reference.RFC.2119.xml'>
    <!ENTITY rfc4690 PUBLIC '' 
      'http://xml.resource.org/public/rfc/bibxml/reference.RFC.4690.xml'>
]>

<rfc category="std" ipr="trust200902" docName="draft-nishida-sctp-failover-00">

<?xml-stylesheet type='text/xsl' href='rfc2629.xslt' ?>

<?rfc toc="yes" ?>
<?rfc symrefs="yes" ?>
<?rfc sortrefs="yes"?>
<?rfc iprnotified="no" ?>
<?rfc strict="yes" ?>

    <front>
        <title abbrev="SCTP Quick Failover">
               Quick Failover Algorithm in SCTP
	</title>

        <author initials='Y.N' surname="Nishida" fullname='Yoshifumi Nishida'>
	  <organization> WIDE Project
            </organization>
	  <address><postal>
<street>Endo 5322</street>
<city>Fujisawa</city> <region>Kanagawa </region><code>252-8520</code>
<country>Japan</country>
	    </postal>
	  <email>nishida@wide.ad.jp</email>
	  </address>
        </author>
        <date/>
        <abstract><t>
   One of the major advantages in SCTP is supporting multi-homing communication. 
   If an multi-homed end-point has redundant network connections, sctp sessions can 
   have a good chance to survive from network failures by migrating inactive 
   network to active one. 
   However, if we follow the SCTP standard, there can be significant delay for the
   network migration. During this migration period, SCTP cannot transmit much data to the 
   destination. This issue drastically impairs the usability of SCTP in some situations. 
   This memo describes the issue of SCTP failover mechanism and discuss its solutions 
   which require minimal modification to the current standard.
         </t></abstract>
    </front>

    <middle>
   <section title="Introduction">
          <t>
   Multihoming support is one of the major advantage of SCTP which is not supported in
   other transport protocols such as TCP or UDP. If an multi-homed end-point has redundant 
   network connections, SCTP sessions can survive from the network failures by migrating 
   inactive path to active one. 
   This feature can be expected to be a driving force for deploying SCTP, however, because of 
   minor issues in the SCTP specification, most of SCTP sessions will have significant delay 
   to failover and will cause significant performance degradation during the failover process. 
   We believe this issue is impairing the usability of SCTP and it is important 
   to address it to make SCTP more efficient and attractive.
         </t>
          <t>
   In this memo, we describes the issue of SCTP failover process and discuss the solutions.
   Our main focus is to propose a solution that does not require major modification to the
   current standard. Using Concurrent Multipath Transfer (CMT) <xref target="IYENGAR06" /> 
   which allows SCTP utilize multiple path simultaneously for data transmission can be an 
   another approach to solve this issue. 
   CMT with sophisticated multi-homing communication control may bring the ideal solution, 
   however, it might require to add a lot of additional functions to the 
   current standard. In addition, some may not want concurrent data transfer feature, 
   but want to use smooth failover feature in SCTP. 
   From this reason, we believe the proposals in this document can be useful and meaningful.
	 </t>
	</section>

   <section title="Conventions and Terminology">
      <t>
	  The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
	  "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
	  document are to be interpreted as described in <xref target="RFC2119"/>.
	  </t>

      <t>
	  Since this document describes a potential risk in NewReno, it uses the same 
	  terminology and definitions in RFC4690. <xref target="RFC4690"/>.
	  </t>

	</section>

   <section title="Issue in SCTP Path Management Process">
          <t>
   SCTP can utilize multiple IP addresses for single SCTP association.
   Each SCTP endpoint exchanges the list of available addresses on the node during initial 
   negotiation. After this, endpoints select one address from the list and define this 
   as the destination of the primary path. Basically, SCTP sends all data through this 
   primary path for normal data transmissions. Also, it sends heartbeat packets to other 
   (non-primary) destinations at a certain interval to check the reachability of the path. 
  </t><t>
   If sender has multiple active destination addresses, it can retransmit data to 
   non-primary destination address when the transmission to the primary times out.
  </t><t>
   When sender receives the acknowledgment for data or heartbeat packets from one of the
   destination addresses, it considers the destination is active. If it fails to receive
   acknowledgments, the error count for the address is increased. 
   If the error counter exceeds the protocol parameter 'Path.Max.Retrans', SCTP endpoint 
   considers the address is inactive.
  </t><t>
   The failover process of SCTP is initiated when the primary path becomes inactive 
   (error counter for the primacy path exceeds Path.Max.Retrans). If the primary path is 
   marked inactive, SCTP chooses new destination address from one of the active destinations 
   and start using this address to send data.
   If the primary path becomes active again, SCTP uses the primary destination for subsequent 
   data transmissions and stop using non-primary one.
  </t><t>

   An issue in this failover process is that it usually takes significant amount of time
   before SCTP switches to the new destination. Let's say the primary path on a multi-homed
   host becomes unavailable and the RTO value for the primary path at that time is around 1 
   second, it usually takes over 30 seconds before SCTP starts to use the secondary path.
   This is because the recommended value for Path.Max.Retrans in the standard is 5, 
   which requires 5 consecutive timeouts before failover takes place
   Before SCTP switches to the secondary address, SCTP keeps trying to send packets to 
   the primary and only retransmitted packets sent to the secondary can be reached 
   at the receiver.
   This slow failover process can cause significant performance degradation and 
   will not be acceptable in some situations.
   </t></section>

<section title="Solutions for Smooth Failover">
 <t>
   The following approach are conceivable for the solutions of this issue.
</t>
 <section title="Reduce Path.Max.Retrans">
   <t>
   If we choose smaller value for Path.Max.Retrans, we can shorten the duration of failover 
   process. In fact, this is recommended in some research results
   <xref target="JUNGMAIER02"/>
   <xref target="GRINNEMO04"/>
   <xref target="FALLON08"/>.
   For example, if we set Path.Max.Retrans to 0, SCTP switches to another destination on a 
   single timeout. However, smaller value for Path.Max.Retrans might cause spurious failover 
   which might cause bouncing paths. 
   In addition, if we use smaller value for Path.Max.Retrans, we may also need to choose 
   smaller value for 'Association.Max.Retrans'. The Association.Max.Retrans indicates the
   threshold for the total number of consecutive error count for the entire SCTP association. 
   If the total of the error count for all paths exceeds this value, the endpoint considers 
   the peer endpoint unreachable and terminates the association. 
   According to the Section 8.2 in RFC4960, we should avoid having the value of 
   Association.Max.Retrans larger than the summation of the Path.Max.Retrans of 
   all the destination addresses. Otherwise, even if all the destination addresses become 
   inactive, the endpoint still considers the peer endpoint reachable. 
   The behavior in this situation is not defined in the RFC and depends on each implementation.
   In order to avoid inconsistent behavior between implementations, we had better use smaller 
   value for Association.Max.Retrans. 
   However, if we choose smaller value for Association.Max.Retrans, associations will prone 
   to be terminated with minor congestion.

  </t><t>
   Another issue is that the interval of heartbeat packet: 'HB.interval' may not be small.
   (recommended value is 30 seconds)  This means once failover takes place, an endpoint 
   might need a certain amount of time to use the primary path again. This can cause 
   undesirable effects in case of spurious failover. If we choose smaller value for HB.interval,
   the traffic used for path probing in a session will be increased.

  </t><t>
   The advantage of turning Path.Max.Retrans is that it requires no modification to the current 
   standard, although it needs to ignore several recommendations. 
   In addition, some research results indicate path bouncing caused by spurious failover 
   does not cause serious problems. We discuss the effect of path bouncing 
   in the section 5. 
    </t>
   </section>
 <section title="Introduce Potential Failure Status in Failure Detection Algorithm">
   <t>
   As seen above, one difficulty of tuning Path.Max.Retrans is that it is required to
   meet the following two inconsistent requirements. 
   <list style="symbols">
    <t>
    In order to respond network failure quickly, we need to mark a path as inactive as
    soon as we detect failure.
    </t>
    <t>
    In order to make an association persistent and robust against network failure, 
    we need to be conservative to mark a path as inactive.
    </t>
   </list>
   </t>
   <t>
   To satisfy these requirements, we propose to introduce "Potential Failure" state
   in failure detection algorithm in SCTP. Potential Failure state is the intermediate
   state between Active and Inactive. It indicates that the path is possibly inactive,
   but not confirmed yet. By using this state, SCTP can respond network failure quickly,
   while it can preserve a conservative policy of marking path as inactive.
   The idea of using Potential Failure state is originally proposed in <xref target="NATARAJAN08" />
   for CMT. 
   </t>
   <t>
   In this algorithm, when sender receives the acknowledgment for data or heartbeat packets 
   from one of the destination addresses, it considers the destination is Active. 
   If it fails to receive acknowledgments, SCTP endpoint increment the error count for the path
   and marks the path as Potential Failure.
   (we might need to have new threshold value for error counter to be conservative 
    to migrate from Active to Potential Failure. But, we choose this way for now)
   </t>
   <t>
   If the primary path is marked Potential Failure, SCTP chooses new destination address 
   from one of the active destinations and start using this address to send data. 
   SCTP endpoints should not send any data packet to paths in Potential Failure state,
   however, it can send heartbeat packets at a certain interval. To allow quick recover from
   Potential Failure state, we also propose to introduce a new protocol parameter 
   'PFHB.Interval'. PFHB.interval is used to determine the interval of heartbeat packets.
   It is recommended that a heartbeat packet is sent once per RTO of each destination address 
   plus PFHB.interval with jittering of +/- 50% of the RTO value. 
   It is also recommended to use relatively smaller value than HB.interval for PFHB.interval.
   </t>
   <t>
   If the heartbeat is answered, SCTP marks the path Active again. If unanswered, 
   SCTP increments the error count and use an exponential backoff algorithm to 
   increase the RTO. If the error count exceeds Path.Max.Retrans, the path is marked 
   as Inactive. If all paths become Potential Failure state, SCTP endpoint should not
   send any data to its peer, while it can send heartbeat packets. Except the use of
   PFHB.interval, other rules of sending heartbeats are completely the same as 
   those of the standard.
   </t>
   <t>
   The advantage of this approach is that we can keep the same values for 
   Path.Max.Retrans, Association.Max.Retrans and HB.interval used in the current implementations,
   while it can respond network failure quickly.
   In addition, new transmission algorithm becomes effective only when the path is 
   in Potential Failure state. When the primary path is in Active or Inactive, the behavior 
   is completely the same as that of the current standard. Hence, the influences
   of the algorithm will be limited.
  </t>
 </section>
</section>

<section title="Discussion">
<section title="Effect of Path Bouncing">
<t>
   The methods described above can accelerate failover process. 
   Hence, it might introduce path bouncing effect which keeps changing the data transmission
   path frequently. This sounds harmful for data transfer, however several research results
   indicate that there is no serious problem with SCTP in terms of path bouncing effect
   <xref target="CARO04" />
   <xref target="CARO05" />.
</t>
<t>
   There are two main reasons for this. First, SCTP is basically designed for multipath 
   communication, which means SCTP maintains all path related parameters (cwnd, ssthresh, 
   RTT, error count, etc) per each destination address. These parameters cannot be affected 
   by path bouncing.  
   In addition, when SCTP migrates to another path, it starts with minimal cwnd because of 
   slow-start. Hence, there is little chance for packet reordering or duplicating.
</t>
<t>
   Second, even if all communication paths between end-nodes share the same bottleneck, 
   the proposed method does not make situations worse. In case of congestion, the current 
   standard tries to transmit data packets to the primary during failover, while the 
   proposed method tries to explore other destinations.
   In any case, the same amount of data packets sent to the same bottleneck. 
</t>
</section>

<section title="Permanent Failover">
<t>
   When primary path becomes active again after failover, SCTP migrates back to the
   primary path. After this, SCTP starts data transfer with minimal cwnd. This is 
   because SCTP must perform slow-start when it migrates to new path. 
   However, this might degrade the communication performance in case that the performance 
   of the alternative path is relatively good. 
   In order to mitigate this effect of slow-start, permanent failover was proposed in 
   <xref target="CARO02"/>.
   Permanent failover allows SCTP to remain the alternative path even if the primacy path
   becomes active again. 
   This approach can improve performance in some cases, however, it will require more
   detail analysis since it might impact on SCTP failover algorithm.
   Since we prefer to keep the current behavior of the standard as possible,
   we recommend not to take this approach for now.
</t>
</section>
</section>

<section title="Security Considerations">
  <t>
   There are no new security considerations introduced in this document.
  </t>
</section>
<section title="IANA Considerations">
	  <t>
   This document does not create any new registries or modify the rules
   for any existing registries managed by IANA.
	  </t>
 </section>
    </middle>

    <back>
        <references title='Normative References'> 
	  &rfc2119; 
	  &rfc4690; 
     <reference anchor="IYENGAR06" target="">
        <front>
            <title> Concurrent Multipath Transfer using SCTP Multihoming
   over Independent End-to-end Paths.</title>
            <author initials="J." surname="Iyengar" fullname="">
                <organization />
            </author>
            <author initials="P." surname="Amer" fullname="">
                <organization />
            </author>
            <author initials="R." surname="Stewart" fullname="">
                <organization />
            </author>
            <date month="10" year="2006" />
        </front>
        <seriesInfo name="IEEE/ACM Trans on Networking" value="14(5)" />
    </reference>

     <reference anchor="NATARAJAN08" target="">
        <front>
            <title> Concurrent Multipath Transfer using SCTP Multihoming: Introducing Potentially-failed Destination State
            </title>
            <author initials="P." surname="Natarajan" fullname="">
                <organization />
            </author>
            <author initials="N." surname="Ekiz" fullname="">
                <organization />
            </author>
            <author initials="J." surname="Iyengar" fullname="">
                <organization />
            </author>
            <author initials="P." surname="Amer" fullname="">
                <organization />
            </author>
            <author initials="R." surname="Stewart" fullname="">
                <organization />
            </author>
            <date month="5" year="2008" />
        </front>
        <seriesInfo name="IFIP Networking" value="" />
    </reference>

    <reference anchor="JUNGMAIER02" target="">
        <front>
            <title> On the use of SCTP in failover scenrarios 
            </title>
            <author initials="A." surname="Jungmaier" fullname="">
                <organization />
            </author>
            <author initials="E." surname="Rathgeb" fullname="">
                <organization />
            </author>
            <author initials="M." surname="Tuexen" fullname="">
                <organization />
            </author>
            <date month="7" year="2002" />
        </front>
        <seriesInfo name="World Multiconference on Systemics, Cybernetics and Informatics" value="" />
    </reference>

     <reference anchor="GRINNEMO04" target="">
        <front>
            <title> Peformance of SCTP-controlled failovers in M3UA-based SIGTRAN networks
            </title>
            <author initials="K-J" surname="Grinnemo" fullname="">
                <organization />
            </author>
            <author initials="A." surname="Brunstrom" fullname="">
                <organization />
            </author>
            <date month="4" year="2004" />
        </front>
        <seriesInfo name="Advanced Simulation Technologies Conference" value="" />
    </reference>


    <reference anchor="FALLON08" target="">
        <front>
            <title>  SCTP Switchover Performance Issues in WLAN Environments
            </title>
            <author initials="S." surname="Fallon" fullname="">
                <organization />
            </author>
            <author initials="P." surname="Jacob" fullname="">
                <organization />
            </author>
            <author initials="Y." surname="Qiao" fullname="">
                <organization />
            </author>
            <author initials="L." surname="Murphy" fullname="">
                <organization />
            </author>
            <author initials="E." surname="Fallon" fullname="">
                <organization />
            </author>
            <author initials="A." surname="Hanley" fullname="">
                <organization />
            </author>
            <date month="1" year="2008" />
        </front>
        <seriesInfo name="IEEE CCNC" value="2008" />
    </reference>

     <reference anchor="CARO04" target="">
        <front>
            <title> End-to-End Failover Thresholds for Transport Layer Multihoming
            </title>
            <author initials="A." surname="Caro Jr." fullname="">
                <organization />
            </author>
            <author initials="P." surname="Amer" fullname="">
                <organization />
            </author>
            <author initials="R." surname="Stewart" fullname="">
                <organization />
            </author>
            <date month="11" year="2004" />
        </front>
        <seriesInfo name="MILCOM 2004" value="" />
    </reference>

     <reference anchor="CARO05" target="">
        <front>
            <title> End-to-End Fault Tolerance using Transport Layer Multihoming
            </title>
            <author initials="A." surname="Caro Jr." fullname="">
                <organization />
            </author>
            <date month="1" year="2005" />
        </front>
        <seriesInfo name="Ph.D Thesis, University of Delaware" value="" />
    </reference>

     <reference anchor="CARO02" target="">
        <front>
            <title> A Two-level Threshold Recovery Mechanism for SCTP
            </title>
            <author initials="A." surname="Caro Jr." fullname="">
                <organization />
            </author>
            <author initials="J." surname="Iyengar" fullname="">
                <organization />
            </author>
            <author initials="P." surname="Amer" fullname="">
                <organization />
            </author>
            <author initials="G." surname="Heinz" fullname="">
                <organization />
            </author>
            <author initials="R." surname="Stewart" fullname="">
                <organization />
            </author>
            <date month="7" year="2002" />
        </front>
        <seriesInfo name="Tech report, CIS Dept, University of Delaware" value="" />
    </reference>

</references>
</back>

</rfc>
