PCE Working Group S. Sivabalan Internet-Draft C. Filsfils Intended status: Standards Track S. Previdi Expires: October 25, 2015 Cisco Systems, Inc. J. Tantsura Ericsson J. Hardwick Metaswitch Networks M. Nanduri Microsoft Corporation April 23, 2015 Carrying Binding Label/Segment-ID in PCE-based Networks. draft-sivabalan-pce-binding-label-sid-00.txt Abstract It is possible to associate a binding label to RSVP-TE signaled Traffic Engineering Label Switching Path or binding Segment-ID (SID) to Segment Routed Traffic Engineering path. Such a binding label/SID can be used by an upstream node for steering traffic into the appropriate TE path to enforce TE policies. This document proposes an approach for reporting binding label/SID to Path Computation Element (PCE) for supporting PCE-based Traffic Engineering policies. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on October 25, 2015. Sivabalan, et al. Expires October 25, 2015 [Page 1] Internet-Draft Binding Label/Segment-ID April 2015 Copyright Notice Copyright (c) 2015 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. Path Binding TLV . . . . . . . . . . . . . . . . . . . . . . . 5 4. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5. Security Considerations . . . . . . . . . . . . . . . . . . . . 6 6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . . 6 7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 7 8. Normative References . . . . . . . . . . . . . . . . . . . . . 7 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 8 Sivabalan, et al. Expires October 25, 2015 [Page 2] Internet-Draft Binding Label/Segment-ID April 2015 1. Introduction A PCE can compute Traffic Engineering paths (TE paths) through a network that are subject to various constraints. Currently, TE paths are either set up using the RSVP-TE signaling protocol or Segment Routed (SR). We refer to such paths as RSVP-TE paths and SR-TE paths respectively in this document. Similar to assigning label to a Forwarding Equivalence Class (FEC) via Label Distribution Protocol (LDP), a binding label can be assigned to a RSVP-TE LSP. If the topmost label of an incoming packet is the binding label, the packet is steered onto the RSVP-TE LSP. As such, any upstream node can use binding labels to steer the packets that it originates to appropriate TE LSPs to enforce TE policy. Similarly, a binding SID (see [I-D.ietf-isis-segment-routing-extensions] and [I-D.ietf-ospf-segment-routing-extensions]) can be used to enforce TE policy with SR-TE path. Note that if an SR-TE path is represented as a forwarding-adjacency, then the corresponding adjacency SID can be used as the binding SID. In such case, the path is advertised using the routing protocols as described in [RFC5440]. The binding SID provides an alternate mechanism without additional overhead on routing protocols. [RFC5440] describes the Path Computation Element Protocol (PCEP) for communication between a Path Computation Client (PCC) and a PCE or between a pair of PCEs.[I-D.ietf-pce-stateful-pce] specifies extension to PCEP that allows a PCC to delegate its LSPs to a PCE. The PCE can then update the state of LSPs delegated to it. [I-D.ietf-pce-pce-initiated-lsp] specifies a mechanism allowing a PCE to dynamically instantiate an LSP on a PCC by sending the path and characteristics of the LSP. The PCEP extension to setup and maintain SR-TE paths is specified in [I-D.ietf-pce-segment-routing]. Binding label/SID has local significance to the ingress node of the corresponding TE path. When a stateful PCE is deployed for setting up TE paths, it may be desirable to report the binding label or SID to the PCE for the purpose of enforcing end-to-end TE policy. A sample Data Center (DC) use-case is illustrated in the following diagram. In the MPLS DC network, an SR LSP (without traffic engineering) is established using a prefix SID advertised by BGP (see [I-D.keyupate-idr-bgp-prefix-sid]). In IP/MPLS WAN, an SR-TE LSP is setup using the PCE. The list of SIDs of the SR-TE LSP is {A, B, C, D}. The gateway node 1 (which is the PCC) allocates a binding SID X and reports it to the PCE. In order for the access node to steer the traffic over the SR-TE LSP, the PCE passes the SID stack {Y, X} where Y is the prefix SID of the gateway node-1 to the access node. In the absence of the binding SID X, the PCE should pass the SID stack {Y, Sivabalan, et al. Expires October 25, 2015 [Page 3] Internet-Draft Binding Label/Segment-ID April 2015 A, B, C, D} to the access node. This example also illustrates the additional benefit of using the binding SID to reduce the number of SIDs imposed on the access nodes with a limited forwarding capacity. SID stack {Y, X} +-----+ _ _ _ _ _ _ _ _ _ _ _ _ _ _| PCE | | +-----+ | ^ | | Binding | .-----. | SID (X) .-----. | ( ) | ( ) V .--( )--. | .--( )--. +------+ ( ) +-------+ ( ) +-------+ |Access|_( MPLS DC Network )_|Gateway|_( IP/MPLS WAN )_|Gateway| | Node | ( ==============> ) |Node-1 | ( ================> ) |Node-2 | +------+ ( SR path ) +-------+ ( SR-TE path ) +-------+ '--( )--' Prefix '--( )--' ( ) SID of ( ) '-----' Node-1 '-----' is Y SIDs for SR-TE LSP: {A, B, C, D} Figure 1: A sample Use-case of Binding SID In this document, we introduce a new OPTIONAL TLV that a PCC can use in order to report the binding label associated with a TE LSP. This TLV is intended for TE LSPs established using RSVP-TE, SR, or any other future method. Also, in the case of SR-TE LSPs, the TLV can carry an MPLS label binding (for SR-TE path with MPLS data-plane) or a binding SID (e.g., IPv6 address for SR-TE paths with IPv6 data- plane). However, use of this TLV for non-MPLS label binding will be described in separate document(s). 2. Terminology The following terminologies are used in this document: LER: Label Edge Router. LSP: Label Switched Path. Sivabalan, et al. Expires October 25, 2015 [Page 4] Internet-Draft Binding Label/Segment-ID April 2015 LSR: Label Switching Router. PCC: Path Computation Client. PCE: Path Computation Element PCEP: Path Computation Element Protocol. SID: Segment ID. SR: Segment Routing. TLV: Type, Length, and Value. 3. Path Binding TLV The new optional TLV is called "TE-PATH-BINDING TLV" whose format is shown in the diagram below is defined to carry binding label or SID for a TE path. This TLV is associated with the LSP object specified in ([I-D.ietf-pce-stateful-pce]). The type of this TLV is to be allocated by IANA. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Binding Type (BT) | Binding Value | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ Binding Value (continued) (variable length) ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 2: TE-PATH-BINDING TLV TE-PATH-BINDING TLV is a generic TLV such that it is able to carry MPLS label binding as well as other types of future bindings (e.g., IPv6 SR path). The one octet Binding Type (BT) field identifies the type of binding included in the TLV. This document specifies the following BT value: o BT = 0: MPLS label (default). 4. Operation The binding value is allocated by PCC and reported to PCE via PCRpt message. If a PCE does not recognize the TE-PATH-BINDING TLV, it Sivabalan, et al. Expires October 25, 2015 [Page 5] Internet-Draft Binding Label/Segment-ID April 2015 MUST ignore the TLV in accordance with ([RFC5440]). If a PCE recognizes the TLV but does not support the TLV, it MUST send PCErr with Error-Type = 2 (Capability not supported). If a TE-PATH-BINDING TLV is absent in PCRpt message, PCE MUST assume that the corresponding LSP does not have any binding. If there are more than one PATH-BINDING TLVs, only the first TLV MUST be processed and the rest MUST be silently ignored. If PCE recognizes an invalid binding value (e.g., label value from the reserved label space when MPLS label binding is used), it MUST send the PCE error message with Error-Type = 10 ("Reception of an invalid object") and Error Value = TBD ("Bad label value") as specified in [I-D.ietf-pce-segment-routing]. If a PCC receives TE-PATH-BINDING TLV in any message, it MUST close the corresponding PCEP session with the reason "Reception of a malformed PCEP message" according ([RFC5440]). Similarly, if a PCE receives a TE-PATH-BINDING TLV in any message other than a PCRpt or if the TE-PATH-BINDING TLV is associated with any object other than LSP object, the PCE MUST close the corresponding PCEP session with the reason "Reception of a malformed PCEP message" according ([RFC5440]). If a PCC wants to withdraw or modify a previously reported binding value, it MUST send a PCRpt message without any TE-PATH-BINDING TLV and with the TE-PATH-BINDING TLV containing the new binding value respectively. 5. Security Considerations No additional security measure is required. 6. IANA Considerations IANA is requested to allocate a new TLV type (recommended value is 31)for TE-PATH-BINDING TLV specified in this document. This document requests that a registry is created to manage the value of the Binding Type field in the TE-PATH-BINDING TLV. Sivabalan, et al. Expires October 25, 2015 [Page 6] Internet-Draft Binding Label/Segment-ID April 2015 Value Description Reference 0 MPLS Label This document 7. Acknowledgements 8. Normative References [I-D.ietf-isis-segment-routing-extensions] Previdi, S., Filsfils, C., Bashandy, A., Gredler, H., Litkowski, S., Decraene, B., and J. Tantsura, "IS-IS Extensions for Segment Routing", draft-ietf-isis-segment-routing-extensions-03 (work in progress), October 2014. [I-D.ietf-ospf-segment-routing-extensions] Psenak, P., Previdi, S., Filsfils, C., Gredler, H., Shakir, R., Henderickx, W., and J. Tantsura, "OSPF Extensions for Segment Routing", draft-ietf-ospf-segment-routing-extensions-04 (work in progress), February 2015. [I-D.ietf-pce-pce-initiated-lsp] Crabbe, E., Minei, I., Sivabalan, S., and R. Varga, "PCEP Extensions for PCE-initiated LSP Setup in a Stateful PCE Model", draft-ietf-pce-pce-initiated-lsp-04 (work in progress), April 2015. [I-D.ietf-pce-segment-routing] Sivabalan, S., Medved, J., Filsfils, C., Crabbe, E., Lopez, V., Tantsura, J., Henderickx, W., and J. Hardwick, "PCEP Extensions for Segment Routing", draft-ietf-pce-segment-routing-03 (work in progress), April 2015. [I-D.ietf-pce-stateful-pce] Crabbe, E., Minei, I., Medved, J., and R. Varga, "PCEP Extensions for Stateful PCE", draft-ietf-pce-stateful-pce-11 (work in progress), April 2015. [I-D.keyupate-idr-bgp-prefix-sid] Patel, K., Ray, S., Previdi, S., and C. Filsfils, "Segment Routing Prefix SID extensions for BGP", draft-keyupate-idr-bgp-prefix-sid-01 (work in progress), April 2015. Sivabalan, et al. Expires October 25, 2015 [Page 7] Internet-Draft Binding Label/Segment-ID April 2015 [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC4206] Kompella, K. and Y. Rekhter, "Label Switched Paths (LSP) Hierarchy with Generalized Multi-Protocol Label Switching (GMPLS) Traffic Engineering (TE)", RFC 4206, October 2005. [RFC5440] Vasseur, JP. and JL. Le Roux, "Path Computation Element (PCE) Communication Protocol (PCEP)", RFC 5440, March 2009. Authors' Addresses Siva Sivabalan Cisco Systems, Inc. 2000 Innovation Drive Kanata, Ontario K2K 3E8 Canada Email: msiva@cisco.com Clarence Filsfils Cisco Systems, Inc. Pegasus Parc De kleetlaan 6a, DIEGEM BRABANT 1831 BELGIUM Email: cfilsfil@cisco.com Stefano Previdi Cisco Systems, Inc. Via Del Serafico, 200 Rome, Rome 00142 Italy Email: sprevidi@cisco.com Sivabalan, et al. Expires October 25, 2015 [Page 8] Internet-Draft Binding Label/Segment-ID April 2015 Jeff Tantsura Ericsson 300 Holger Way San Jose, CA 95134 USA Email: jeff.tantsura@ericsson.com Jonathan Hardwick Metaswitch Networks 100 Church Street Enfield, Middlesex UK Email: Jonathan.Hardwick@metaswitch.com Mohan Nanduri Microsoft Corporation One Microsoft Way Redmond, WA 98052 USA Email: mnanduri@microsoft.com Sivabalan, et al. Expires October 25, 2015 [Page 9]