Network Working Group R. Bush Internet-Draft IIJ Intended status: Standards Track R. Austein Expires: August 24, 2010 ISC February 20, 2010 The RPKI/Router Protocol draft-ymbk-rpki-rtr-protocol-05 Abstract In order to formally validate the origin ASes of BGP announcements, routers need a simple but reliable mechanism to receive RPKI [I-D.ietf-sidr-arch] or analogous prefix origin data from a trusted cache. This document describes a protocol to deliver validated prefix origin data to routers over ssh. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. Status of this Memo This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79. This document may not be modified, and derivative works of it may not be created, and it may not be published except as an Internet-Draft. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on August 24, 2010. Bush & Austein Expires August 24, 2010 [Page 1] Internet-Draft The RPKI/Router Protocol February 2010 Copyright Notice Copyright (c) 2010 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Deployment Structure . . . . . . . . . . . . . . . . . . . . . 4 3. Operational Overview . . . . . . . . . . . . . . . . . . . . . 4 4. Protocol Data Units (PDUs) . . . . . . . . . . . . . . . . . . 5 4.1. Serial Notify . . . . . . . . . . . . . . . . . . . . . . 6 4.2. Serial Query . . . . . . . . . . . . . . . . . . . . . . . 6 4.3. Reset Query . . . . . . . . . . . . . . . . . . . . . . . 7 4.4. Cache Response . . . . . . . . . . . . . . . . . . . . . . 7 4.5. IPv4 Prefix . . . . . . . . . . . . . . . . . . . . . . . 8 4.6. IPv6 Prefix . . . . . . . . . . . . . . . . . . . . . . . 9 4.7. End of Data . . . . . . . . . . . . . . . . . . . . . . . 9 4.8. Cache Reset . . . . . . . . . . . . . . . . . . . . . . . 10 4.9. Error Report . . . . . . . . . . . . . . . . . . . . . . . 10 4.10. Fields of a PDU . . . . . . . . . . . . . . . . . . . . . 11 5. Protocol Sequences . . . . . . . . . . . . . . . . . . . . . . 12 5.1. Start or Restart . . . . . . . . . . . . . . . . . . . . . 12 5.2. Typical Exchange . . . . . . . . . . . . . . . . . . . . . 13 5.3. No Incremental Update Available . . . . . . . . . . . . . 14 5.4. Cache has No Data Available . . . . . . . . . . . . . . . 14 6. SSH Transport . . . . . . . . . . . . . . . . . . . . . . . . 15 7. Router-Cache Set-Up . . . . . . . . . . . . . . . . . . . . . 15 8. Deployment Scenarios . . . . . . . . . . . . . . . . . . . . . 16 9. Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . 17 10. Security Considerations . . . . . . . . . . . . . . . . . . . 17 11. Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 12. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 19 13. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 19 14. References . . . . . . . . . . . . . . . . . . . . . . . . . . 19 14.1. Normative References . . . . . . . . . . . . . . . . . . . 19 14.2. Informative References . . . . . . . . . . . . . . . . . . 20 Bush & Austein Expires August 24, 2010 [Page 2] Internet-Draft The RPKI/Router Protocol February 2010 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 20 Bush & Austein Expires August 24, 2010 [Page 3] Internet-Draft The RPKI/Router Protocol February 2010 1. Introduction In order to formally validate the origin ASes of BGP announcements, routers need a simple but reliable mechanism to receive RPKI [I-D.ietf-sidr-arch] or analogous formally validated prefix origin data from a trusted cache. This document describes a protocol to deliver validated prefix origin data to routers over ssh. Section 2 describes the deployment structure and Section 3 then presents an operational overview. The binary payloads of the protocol are formally described in Section 4, and the expected PDU sequences are described in Section 5. And the transport protocol is described in Section 6. Section 7 details how routers and caches are configured to connect and authenticate. Section 8 describes likely deployment scenarios. The traditional security and IANA considerations end the document. 2. Deployment Structure Deployment of the RPKI to reach routers has a three level structure as follows: Global RPKI: The authoritative data of the RPKI are published in a distributed set of servers, RPKI publication repositories, e.g. the IANA, RIRs, NIRs, and ISPs, see [I-D.ietf-sidr-repos-struct]. Local Caches: A local set of one or more collected and verified non- authoritative caches. A relying party, e.g. router or other client, MUST have a formally authenticated trust relationship with, and a secure transport channel to, any non-authoritative cache(s) it uses. Routers: A router fetches data from a local cache using the protocol described in this document. It is said to be a client of the cache. There are mechanisms for the router to assure itself of the authenticity of the cache and to authenticate itself to the cache. 3. Operational Overview A router establishes and keeps open an authenticated connection to a cache with which it has an client/server relationship. It is configured with a semi-ordered list of caches, and establishes a connection to the highest preference cache that accepts one. Periodically, the router sends to the cache the serial number of the Bush & Austein Expires August 24, 2010 [Page 4] Internet-Draft The RPKI/Router Protocol February 2010 highest numbered data record it has received from that cache, i.e. the router's current serial number. When a router establishes a new connection to a cache, or wishes to reset a current relationship, it sends a Reset Query. The Cache responds with all data records which have serial numbers greater than that in the router's query. This may be the null set, in which case the End of Data PDU is still sent. Note that 'greater' must take wrap-around into account, see [RFC1982]. When the router has received all data records from the cache, it sets its current serial number to that of the serial number in the End of Data PDU. When the cache updates its database, it sends a Notify message to every currently connected router. This is a hint that now would be a good time for the router to poll for an update, but is only a hint. The protocol requires the router to poll for updates periodically in any case. Strictly speaking, a router could track a cache simply by asking for a complete data set every time it updates, but this would be very inefficient. The serial number based incremental update mechanism allows an efficient transfer of just the data records which have changed since last update. As with any update protocol based on incremental transfers, the router must be prepared to fall back to a full transfer if for any reason the cache is unable to provide the necessary incremental data. Unlike some incremental transfer protocols, this protocol requires the router to make an explicit request to start the fallback process; this is deliberate, as the cache has no way of knowing whether the router has also established sessions with other caches that may be able to provide better service. 4. Protocol Data Units (PDUs) The exchanges between the cache and the router are sequences of exchanges of the following PDUs according to the rules described in Section 5. Bush & Austein Expires August 24, 2010 [Page 5] Internet-Draft The RPKI/Router Protocol February 2010 4.1. Serial Notify The cache notifies the router that the cache has new data. 0 8 16 24 31 .-------------------------------------------. | Protocol | PDU | | | Version | Type | reserved = zero | | 0 | 0 | | +-------------------------------------------+ | | | Length | | | +-------------------------------------------+ | | | Serial Number | | | `-------------------------------------------' 4.2. Serial Query Serial Query: The router sends Serial Query to ask the cache for all payload PDUs which have serial numbers higher than the serial number in the Serial Query. The cache replys to this query with a Cache Response PDU (Section 4.4) if the cache has a record of the changes since the serial number specified by the router. If there have been no changes since the router last queried, the cache responds with an End Of Data PDU. If the cache does not have the data needed to update the router, perhaps because its records do not go back to the Serial Number in the Serial Query, then cache responds with a Cache Reset PDU (Section 4.8). 0 8 16 24 31 .-------------------------------------------. | Protocol | PDU | | | Version | Type | reserved = zero | | 0 | 1 | | +-------------------------------------------+ | | | Length=12 | | | +-------------------------------------------+ | | | Serial Number | | | `-------------------------------------------' Bush & Austein Expires August 24, 2010 [Page 6] Internet-Draft The RPKI/Router Protocol February 2010 4.3. Reset Query Reset Query: The router tells the cache that it wants to receive the total active, current, non-withdrawn, database. The cache responds with a Cache Response PDU (Section 4.4). 0 8 16 24 31 .-------------------------------------------. | Protocol | PDU | | | Version | Type | reserved = zero | | 0 | 2 | | +-------------------------------------------+ | | | Length=8 | | | `-------------------------------------------' 4.4. Cache Response Cache Response: The cache responds with zero or more payload PDUs. When replying to a Serial Query request (Section 4.2), the cache sends the set of all data records it has with serial numbers greater than that sent by the client router. When replying to a Reset Query, the cache sends the set of all data records it has; in this case the withdraw/announce field in the payload PDUs MUST have the value 1 (announce). 0 8 16 24 31 .-------------------------------------------. | Protocol | PDU | | | Version | Type | reserved = zero | | 0 | 3 | | +-------------------------------------------+ | | | Length=8 | | | `-------------------------------------------' Bush & Austein Expires August 24, 2010 [Page 7] Internet-Draft The RPKI/Router Protocol February 2010 4.5. IPv4 Prefix 0 8 16 24 31 .-------------------------------------------. | Protocol | PDU | | | Version | Type | Color | | 0 | 4 | | +-------------------------------------------+ | | | Length=20 | | | +-------------------------------------------+ | | Prefix | Max | Data | | Flags | Length | Length | Source | | | 0..32 | 0..32 | RPKI/IRR | +-------------------------------------------+ | | | IPv4 prefix | | | +-------------------------------------------+ | | | Autonomous System Number | | | `-------------------------------------------' Due to the nature of the RPKI and the IRR, there can be multiple identical IPvX PDUs. Hence the router will likely keep an internal ref-count on each IPvX PDU. In the RPKI, nothing prevents a signing certificate from issuing two identical ROAs, and nothing prohibits the existence of two identical route: or route6: objects in the IRR. In this case there would be no semantic difference between the objects, merely a process redundancy. In the RPKI, there is also an actual need for what will appear to the router as identical IPvX PDUs. This occurs when an upstream certificate is being reissued or a site is changing providers, often a 'make and break' situation. The ROA is identical in the router sense, i.e. has the same {prefix, len, max-len, asn}, but has a different validation path in the RPKI. This is important to the RPKI, but not to the router. The lowest order bit of the Flags field is 1 for an announcement and 0 for a withdrawal. Bush & Austein Expires August 24, 2010 [Page 8] Internet-Draft The RPKI/Router Protocol February 2010 4.6. IPv6 Prefix 0 8 16 24 31 .-------------------------------------------. | Protocol | PDU | | | Version | Type | Color | | 0 | 6 | | +-------------------------------------------+ | | | Length=40 | | | +-------------------------------------------+ | | Prefix | Max | Data | | Flags | Length | Length | Source | | | 0..128 | 0..128 | RPKI/IRR | +-------------------------------------------+ | | +--- ---+ | | +--- IPv6 prefix ---+ | | +--- ---+ | | +-------------------------------------------+ | | | Autonomous System Number | | | `-------------------------------------------' 4.7. End of Data End of Data: Cache tells router it has no more data for the request. 0 8 16 24 31 .-------------------------------------------. | Protocol | PDU | | | Version | Type | reserved = zero | | 0 | 7 | | +-------------------------------------------+ | | | Length=12 | | | +-------------------------------------------+ | | | Serial Number | | | `-------------------------------------------' Bush & Austein Expires August 24, 2010 [Page 9] Internet-Draft The RPKI/Router Protocol February 2010 4.8. Cache Reset The cache may respond to a Serial Query informing the router that the cache cannot provide an incremental update starting from the serial number specified by the router. The router must decide whether to issue a Reset Query or switch to a different cache. 0 8 16 24 31 .-------------------------------------------. | Protocol | PDU | | | Version | Type | reserved = zero | | 0 | 8 | | +-------------------------------------------+ | | | Length=8 | | | `-------------------------------------------' 4.9. Error Report This PDU is used by either party to report an error to the other. If the error is not associated with any particular PDU, the Erroneous PDU field should be empty and the Length of Encapsulated PDU field should be zero. The diagnostic text is optional, if not present the Length of Error Text field should be zero. If error text is present, it SHOULD be a string in US-ASCII, for maximum portability; if non-US-ASCII characters are absolutely required, the error text MUST use UTF-8 encoding. Bush & Austein Expires August 24, 2010 [Page 10] Internet-Draft The RPKI/Router Protocol February 2010 0 8 16 24 31 .-------------------------------------------. | Protocol | PDU | | | Version | Type | Error Number | | 0 | 10 | | +-------------------------------------------+ | | | Length | | | +-------------------------------------------+ | | | Length of Encapsulated PDU | | | +-------------------------------------------+ | | ~ Copy of Erroneous PDU ~ | | +-------------------------------------------+ | | | Length of Error Text | | | +-------------------------------------------+ | | | Arbitrary Text | | of | ~ Error Diagnostic Message ~ | | `-------------------------------------------' 4.10. Fields of a PDU PDUs contain the following data elements: Protocol Version: A cardinal, currently 0, denoting the version of this protocol. Serial Number: The serial number of the RPKI Cache when this ROA was received from the cache's up-stream cache server or gathered from the global RPKI. A cache increments its serial number when completing an rcynic from a parent cache. See [RFC1982] on DNS Serial Number Arithmetic for too much detail on serial number arithmetic. Length: A 32 bit cardinal which has as its value the count of the bytes in the entire PDU, including the eight bytes of header which end with the length field. Bush & Austein Expires August 24, 2010 [Page 11] Internet-Draft The RPKI/Router Protocol February 2010 Color: An arbitrary 16 bit field that might be used in some way. Flags: The lowest order bit of the Flags field is 1 for an announcement and 0 for a withdrawal, whether this PDU announces a new right to announce the prefix or withdraws a previously announced right. A withdraw effectively deletes one previously announced IPvX Prefix PDU with the exact same Prefix, Length, Max- Len, ASN, Data Source, and Color. Prefix Length: A cardinal denoting the shortest prefix allowed for the prefix. Max Length: A cardinal denoting the longest prefix allowed by the prefix. This MUST NOT be less than the Prefix Length element. Data Source: A cardinal denoting the source of the data, e.g. for RPKI data, it is 0, for IRR data it is 1. Prefix: The IPv4 or IPv6 prefix of the ROA. Autonomous System Number: ASN allowed to announce this prefix, a 32 bit cardinal. 5. Protocol Sequences The sequences of PDU transmissions fall into three conversations as follows: 5.1. Start or Restart Cache Router ~ ~ | <----- Reset Query -------- | R requests data | | | ----- Cache Response -----> | C confirms request | ------- IPvX Prefix ------> | C sends zero or more | ------- IPvX Prefix ------> | IPv4 and IPv6 Prefix | ------- IPvX Prefix ------> | Payload PDUs | ------ End of Data ------> | C sends End of Data | | and sends new serial ~ ~ When a transport session is first established, the router sends a Reset Query and the cache responds with a data sequence of all data it contains. This Reset Query sequence is also used when the router receives a Bush & Austein Expires August 24, 2010 [Page 12] Internet-Draft The RPKI/Router Protocol February 2010 Cache Reset, chooses a new cache, or fears that it has otherwise lost its way. To limit the length of time a cache must keep the data necessary to generate incremental updates, a router MUST send either a Serial Query or a Reset Query no less frequently than once an hour. This also acts as a keep alive at the application layer. 5.2. Typical Exchange Cache Router ~ ~ | -------- Notify ----------> | (optional) | | | <----- Serial Query ------- | R requests data | | | ----- Cache Response -----> | C confirms request | ------- IPvX Prefix ------> | C sends zero or more | ------- IPvX Prefix ------> | IPv4 and IPv6 Prefix | ------- IPvX Prefix ------> | Payload PDUs | ------ End of Data ------> | C sends End of Data | | and sends new serial ~ ~ The cache server SHOULD send a notify PDU with its current serial number when the cache's serial changes, with the expectation that the router MAY then issue a serial query earlier than it otherwise might. This is analogous to DNS NOTIFY in [RFC1996]. The cache SHOULD rate limit Serial Notifies to no more frequently than one per minute. When the transport layer is up and either a timer has gone off in the router, or the cache has sent a Notify, the router queries for new data by sending a Serial Query, and the cache sends all data newer than the serial in the Serial Query. To limit the length of time a cache must keep old withdraws, a router MUST send either a Serial Query or a Reset Query no less frequently than once an hour. Bush & Austein Expires August 24, 2010 [Page 13] Internet-Draft The RPKI/Router Protocol February 2010 5.3. No Incremental Update Available Cache Router ~ ~ | <----- Serial Query ------ | R requests data | ------- Cache Reset ------> | C cannot supply update | | from specified serial | <------ Reset Query ------- | R requests new data | ----- Cache Response -----> | C confirms request | ------- IPvX Prefix ------> | C sends zero or more | ------- IPvX Prefix ------> | IPv4 and IPv6 Prefix | ------- IPvX Prefix ------> | Payload PDUs | ------ End of Data ------> | C sends End of Data | | and sends new serial ~ ~ The cache may respond to a Serial Query with a Cache Reset, informing the router that the cache cannot supply an incremental update from the serial number specified by the router. This might be because the cache has lost state, or because the router has waited too long between polls and the cache has cleaned up old data that it no longer believes it needs, or because the cache has run out of storage space and had to expire some old data early. Regardless of how this state arose, the cache replies with a Cache Reset to tell the router that it cannot honor the request. When a router receives this, the router SHOULD attempt to connect to any more preferred caches in its cache list. If there are no more preferred caches it MUST issue a Reset Query and get an entire new load from the cache 5.4. Cache has No Data Available Cache Router ~ ~ | <----- Serial Query ------ | R requests data | ---- Error Report PDU ----> | C cannot supply update ~ ~ Cache Router ~ ~ | <----- Reset Query ------- | R requests data | ---- Error Report PDU ----> | C cannot supply update ~ ~ The cache may respond to either a Serial Query or a Reset Query informing the router that the cache cannot supply any update at all. The most likely cause is that the cache has lost state, perhaps due to a restart, and has not yet recovered. While it is possible that a cache might go into such a state without dropping any of its active Bush & Austein Expires August 24, 2010 [Page 14] Internet-Draft The RPKI/Router Protocol February 2010 sessions, a router is more likely to see this behavior when it initially connects and issues a Reset Query while the cache is still rebuilding its database. When a router receives this kind of error, the router SHOULD attempt to connect to any other caches in its cache list, in preference order. If no other caches are available, the router MUST issue periodic Reset Queries until it gets a new usable load from the cache 6. SSH Transport The transport layer session between a router and a cache carries the binary Protocol Data Units (PDUs) in a persistent SSH session. To run over SSH, the client router first establishes an SSH transport connection using the SSH transport protocol, and the client and server exchange keys for message integrity and encryption. The client then invokes the "ssh-userauth" service to authenticate the application, as described in the SSH authentication protocol RFC 4252 [RFC4252]. Once the application has been successfully authenticated, the client invokes the "ssh-connection" service, also known as the SSH connection protocol. After the ssh-connection service is established, the client opens a channel of type "session", which results in an SSH session. Once the SSH session has been established, the application invokes the application transport as an SSH subsystem called "rpki-rtr". Subsystem support is a feature of SSH version 2 (SSHv2) and is not included in SSHv1. Running this protocol as an SSH subsystem avoids the need for the application to recognize shell prompts or skip over extraneous information, such as a system message that is sent at shell start-up. It is assumed that the router and cache have exchanged keys out of band by some reasonably secured means. 7. Router-Cache Set-Up A cache has the public authentication data for each router it is configured to support. A router may be configured to peer with a selection of caches, and a cache may be configured to support a selection of routers. So each must have the name of each peer and authentication data for each. In addition, in a router, this list has a non-unique preference value Bush & Austein Expires August 24, 2010 [Page 15] Internet-Draft The RPKI/Router Protocol February 2010 for each server in order of preference. The client router attempts to establish a session with each potential serving cache in preference order, and then starts to load data from the highest preference cache to which it can connect and authenticate. The router's list of caches has the following elements: Preference: A cardinal denoting the router's preference to use that cache, the lower the value the more preferred. Name: The IP Address or fully qualified domain name of the cache. Key: The public ssh key of the cache. MyKey: The private ssh key of this client. As caches can not be rigorously synchronous, a client which changes servers can not combine data from different parent caches. Therefore, when a lower preference cache becomes available, if resources allow, it would be prudent for the client to start a new buffer for that cache's data, and only switch to those data when that buffer is fully up to date. 8. Deployment Scenarios For illustration, we present three likely deployment scenarios. Small End Site: The small multi-homed end site may wish to outsource the RPKI cache to one or more of their upstream ISPs. They would exchange authentication material with the ISP using some out of band mechanism, and their router(s) would connect to one or more up-streams' caches. The ISPs would likely deploy caches intended for customer use separately from the caches with which their own BGP speakers peer. Large End Site: A larger multi-homed end site might run one or more caches, arranging them in a hierarchy of client caches, each fetching from a serving cache which is closer to the global RPKI. They might configure fall-back peerings to up-stream ISP caches. ISP Backbone: A large ISP would likely have one or more redundant caches in each major PoP, and these caches would fetch from each other in an ISP-dependent topology so as not to place undue load on the global RPKI publication infrastructure. Experience with large DNS cache deployments has shown that complex topologies are ill-advised as it is easy to make errors in the graph, e.g. not maintaining a loop-free condition. Bush & Austein Expires August 24, 2010 [Page 16] Internet-Draft The RPKI/Router Protocol February 2010 Of course, these are illustrations and there are other possible deployment strategies. It is expected that minimizing load on the global RPKI servers will be a major consideration. To keep load on global RPKI services from unnecessary peaks, it is recommended that primary caches which load from the distributed global RPKI not do so all at the same times, e.g. on the hour. Choose a random time, perhaps the ISP's AS number modulo 60 and jitter the inter-fetch timing. 9. Error Codes This section contains a preliminary list of error codes. The authors expect additions to this section during development of the initial implementations. Eventually, these error codes will probably need to reside in an IANA registry. 0: Reserved. 1: Internal Error: The party reporting the error experienced some kind of internal error unrelated to protocol operation (ran out of memory, a coding assertion failued, etcetera). 2: No Data Available: The cache believes itself to be in good working order, but is unable to answer either a Serial Query or a Reset Query because it has no useful data available at this time. This is likely to be a temporary error, and most likely indicates that the cache has not yet completed pulling down an initial current data set from the global RPKI system after some kind of event that invalidated whatever data it might have previously held (reboot, network partition, etcetera). 10. Security Considerations As this document describes a security protocol, many aspects of security interest are described in the relevant sections. This section points out issues which may not be obvious in other sections. Cache Validation: In order for a collection of caches as described in Section 8 to guarantee a consistent view, they need to be given consistent trust anchors to use in their internal validation process. Distribution of a consistent trust anchor is assumed to be out of band. Bush & Austein Expires August 24, 2010 [Page 17] Internet-Draft The RPKI/Router Protocol February 2010 Cache Peer Identification: As the router initiates an ssh transport session to a cache which it identifies by either IP address or fully qualified domain name, a DNS or address spoofing attack could make the correct cache unreachable. No session would be established, as the authorization keys would not match. Transport Security: The RPKI relies on object, not server or transport, trust. I.e. the IANA root trust anchor is distributed to all caches through some out of band means, and can then be used by each cache to validate certificates and ROAs all the way down the tree. The inter-cache relationships are based on this object security model, hence the inter-cache transport can be lightly protected. But this protocol document assumes that the routers can not do the validation cryptography. Hence the last link, from cache to router, is secured by server authentication and transport level security. This is dangerous, as server authentication and transport have very different threat models than object security. So the strength of the trust relationship and the transport between the router(s) and the cache(s) are critical. You're betting your routing on this. While we can not say the cache must be on the same LAN, if only due to the issue of an enterprise wanting to off-load the cache task to their upstream ISP(s), locality, trust, and control are very critical issues here. The cache(s) really SHOULD be as close, in the sense of controlled and protected (against DDoS, MITM) transport, to the router(s) as possible. It also SHOULD be topologically close so that a minimum of validated routing data are needed to bootstrap a router's access to a cache. 11. Glossary The following terms are used with special meaning: Global RPKI: The authoritative data of the RPKI are published in a distributed set of servers at the IANA, RIRs, NIRs, and ISPs, see [I-D.ietf-sidr-repos-struct]. Non-authorative Cache: A coalesced copy of the RPKI which is periodically fetched/refreshed directly or indirectly from the global RPKI using the [rcynic] protocol/tools Bush & Austein Expires August 24, 2010 [Page 18] Internet-Draft The RPKI/Router Protocol February 2010 Cache: The rcynic system is used to gather the distributed data of the RPKI into a validated cache. Trusting this cache further is a matter between the provider of the cache and a relying party. Serial Number: A 32-bit monotonically increasing, cardinal which wraps from 2^32-1 to 0. It denotes the logical version of a cache. A cache increments the value by one when it successfully updates its data from a parent cache or from primary RPKI data. As a cache is rcynicing, new incoming data, and implicit deletes, are marked with the new serial but MUST not be sent until the fetch is complete. A serial number is not commensurate between caches, nor need it be maintained across resets of the cache server. See [RFC1982] on DNS Serial Number Arithmetic for too much detail on serial number arithmetic. 12. IANA Considerations This document requests the IANA to create a registry for PDU types. This document requests the IANA to create a registry for Error Codes. In addition, a registry for Version Numbers would be needed if new Version Number is defined in a new RFC. Note to RFC Editor: this section may be replaced on publication as an RFC. 13. Acknowledgments The authors wish to thank Steve Bellovin, Rex Fernando, Russ Housley, Pradosh Mohapatra, Sandy Murphy, Megumi Ninomiya, Robert Raszuk, John Scudder, Ruediger Volk, David Ward, and Bert Wijnen. 14. References 14.1. Normative References [RFC1982] Elz, R. and R. Bush, "Serial Number Arithmetic", RFC 1982, August 1996. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", RFC 2119, BCP 14, March 1997. [RFC4252] Ylonen, T. and C. Lonvick, "The Secure Shell (SSH) Authentication Protocol", RFC 4252, January 2006. Bush & Austein Expires August 24, 2010 [Page 19] Internet-Draft The RPKI/Router Protocol February 2010 [rcynic] Austein, R., "rcynic protocol", . 14.2. Informative References [I-D.ietf-sidr-arch] Lepinski, M. and S. Kent, "An Infrastructure to Support Secure Internet Routing", draft-ietf-sidr-arch-06 (work in progress), March 2009. [I-D.ietf-sidr-repos-struct] Huston, G., Loomans, R., and G. Michaelson, "A Profile for Resource Certificate Repository Structure", draft-ietf-sidr-repos-struct-01 (work in progress), October 2008. [RFC1996] Vixie, P., "A Mechanism for Prompt Notification of Zone Changes (DNS NOTIFY)", RFC 1996, August 1996. Authors' Addresses Randy Bush Internet Initiative Japan, Inc. 5147 Crystal Springs Bainbridge Island, Washington 98110 US Phone: +1 206 780 0431 x1 Email: randy@psg.com Rob Austein Internet Systems Consortium 950 Charter Street Redwood City, CA 94063 USA Email: sra@isc.org Bush & Austein Expires August 24, 2010 [Page 20]