INTERNET-DRAFT B. Jewell October 5, 1999 D. Chuang 3Com, Inc. Definitions of Managed Objects for the Virtual Router Redundancy Protocol Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet- Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This internet draft expires on April 5, 2000. Abstract This specification defines an extension to the Management Information Base (MIB) for use with SNMP-based network management. In particular, it defines objects for configuring, monitoring, and controlling routers that employ the Virtual Router Redundancy Protocol (VRRP) [17]. This memo specifies a MIB module in a manner that is compliant with SMIv2 [5], and semantically identical to the SMIv1 definitions [2]. draft-ietf-vrrp-mib-09.txt [Page 1] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 Table of Contents 1 The SNMP Network Management Framework ................. 3 2 Overview .............................................. 4 2.1 VRRP MIB Structure .................................. 4 2.2 Virtual Router Redundancy Protocol .................. 4 2.3 VRRP MIB Table Design ............................... 5 2.3.1 Relation to Interface Group ....................... 5 2.4 VRRP Scenarios ...................................... 5 2.4.1 Scenario #1 ....................................... 6 2.4.2 Scenario #2 ....................................... 8 3 Definitions ........................................... 11 4 Security Considerations ............................... 31 5 Acknowledgements ...................................... 32 6 References ............................................ 32 7 Authors' Addresses .................................... 34 8 Intellectural Property Statement....................... 34 9 Full Copyright Statement............................... 35 draft-ietf-vrrp-mib-09.txt [Page 2] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 1. The SNMP Management Framework The SNMP Management Framework presently consists of five major components: o An overall architecture, described in RFC 2571 [1]. o Mechanisms for describing and naming objects and events for the purpose of management. The first version of this Structure of Management Information (SMI) is called SMIv1 and described in RFC 1155 [2], RFC 1212 [3] and RFC 1215 [4]. The second version, called SMIv2, is described in RFC 2578 [5], RFC 2579 [6] and RFC 2580 [7]. o Message protocols for transferring management information. The first version of the SNMP message protocol is called SNMPv1 and described in RFC 1157 [8]. A second version of the SNMP message protocol, which is not an Internet standards track protocol, is called SNMPv2c and described in RFC 1901 [9] and RFC 1906 [10]. The third version of the message protocol is called SNMPv3 and described in RFC 1906 [10], RFC 2572 [11] and RFC 2574 [12]. o Protocol operations for accessing management information. The first set of protocol operations and associated PDU formats is described in RFC 1157 [8]. A second set of protocol operations and associated PDU formats is described in RFC 1905 [13]. o A set of fundamental applications described in RFC 2573 [14] and the view-based access control mechanism described in RFC 2575 [15]. A more detailed introduction to the current SNMP Management Framework can be found in RFC 2570 [16]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the mechanisms defined in the SMI. This memo specifies a MIB module that is compliant to the SMIv2. A MIB conforming to the SMIv1 can be produced through the appropriate translations. The resulting translated MIB must be semantically equivalent, except where objects or events are omitted because no translation is possible (use of Counter64). Some machine readable information in SMIv2 will be converted into textual descriptions in SMIv1 during the translation process. However, this loss of machine readable information is not considered to change the semantics of the MIB. draft-ietf-vrrp-mib-09.txt [Page 3] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 2. Overview This memo identifies the set of objects for configuring, monitoring, and controlling the Virtual Router Redundancy Protocol (VRRP), as defined in RFC 2338 [17]. VRRP specifies an election protocol that will allow one or more associated IP addresses to be assumed by another router in the event of a failure of the IP address(es) owner. Thus, IP traffic from a host using a failed router as a default gateway is transparently fowarded by the VRRP router that has assumed control. VRRP provides redundancy in routed networks without requiring configuration of dynamic routing or router discovery protocols on every end-host. Since the VRRP protocol is intended for use with IPv4 routers only, this MIB uses the SYNTAX for IP addresses which is specific to IPv4. Thus, changes will be required for this MIB to interoperate in an IPv6 environment. 2.1. VRRP MIB Structure The VRRP MIB contains three conformance groups: - vrrpOperations Group: Objects related to VRRP router's configuration and control. - vrrpStatistics Group: Objects containing information useful in monitoring the operation of VRRP routers. - vrrpNotifications Group: Consists of objects and definitions for use in SNMP notifications sent by VRRP routers. Tables in the MIB include the following: (1) The vrrpOperTable, which contains objects that define the operational characteristics of a VRRP router. Rows in this table correspond to instances of virtual routers. (2) The vrrpAssoIpAddrTable, which contains the addresses of the virtual router(s) that a given VRRP router is backing up. (3) The vrrpRouterStatsTable which contains the operating statistics for a VRRP router. draft-ietf-vrrp-mib-09.txt [Page 4] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 2.2. Virtual Router Redundancy Protocol This MIB is based on the following characteristics of VRRP as defined in the VRRP specification [17]. - A "VRRP router" is one that is configured to run the VRRP protocol in conjunction with one or more other VRRP routers attached to a LAN. - A VRRP router can be running one or more instances of a virtual router. - A "virtual router" is an abstraction which consists of two or more physical routers associated by a Virtual Router Identifier (VRID). - An instance of a virtual router (on a physical VRRP router), can be uniquely identified by a combination of the 'ifIndex' [18] and "Virtual Router Identifier" (VRID). - For each VRID there is a set of one or more "associated IP addresses" that are backed-up by the virtual router. 2.3. VRRP MIB Table Design The tables in the VRRP MIB are structured with the assumption that a VRRP network management application would likely be designed to display information or provide configuration about a VRRP router on a "per-virtual-router basis". Thus, the tables defined in the MIB consist of conceptual rows which are grouped in a manner to present a view of individual virtual routers with a minimal number of SNMP operations. 2.3.1. Relation to Interface Group (RFC 2233) [18]. Since a router can be participating in VRRP on one or more physical interfaces, "ifIndex" is used as an index into the tables defined in the VRRP MIB. 2.4. VRRP Scenarios The following section provides examples of how some of the objects in this MIB are instantiated for two different VRRP scenarios. draft-ietf-vrrp-mib-09.txt [Page 5] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 KEY: ---- The labels in the following tables and diagrams correspond to the actual MIB objects as follows: if = vrrpOperIfIndex VrId = vrrpOperVrId State = vrrpOperState Prior = vrrpOperPriority AddrCnt = vrrpOperIpAddrCount IpAddr = vrrpOperMasterIpAddr RowStat = vrrpOperRowStatus 2.4.1. VRRP Scenario #1 The following figure shows a simple network with two VRRP routers configured with two virtual routers. This sample topology is taken from the VRRP specification [17]. Addresses in '()' indicate the IP address of the default gateway for a given host, H1 - H4. In the diagram, "Interface" is used in the context defined in IF-MIB [18]. VRID=1 VRID=2 +-----+ +-----+ | MR1 | | MR2 | | & | | & | | BR2 | | BR1 | +-----+ +-----+ IP A ---------->* *<---------- IP B Interface=I1 | | Interface=I2 | | | | ------------------+------------+-----+--------+--------+--------+-- ^ ^ ^ ^ | | | | (IP A) (IP A) (IP A) (IP A) | | | | +--+--+ +--+--+ +--+--+ +--+--+ | H1 | | H2 | | H3 | | H4 | +-----+ +-----+ +--+--+ +--+--+ draft-ietf-vrrp-mib-09.txt [Page 6] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 ----- MIB Tables For VRRP Router "IP A": ----- vrrpOperTable ------------- | if | VrId | State | Prior | AddrCnt | IpAddr | ... | RowStat | +----+------+-------+-------+---------+--------+-( )-+---------+ | | | | | | | | | | I1 | 01 | M | 255 | 1 | A | | active | | | | | | | | | | +----+------+-------+-------+---------+--------+-( )-+---------+ | | | | | | | | | | I1 | 02 | B | 1-254 | 1 | B | | active | | | | | | | | | | +----+------+-------+-------+---------+--------+-( )-+---------+ vrrpAssoIpAddrTable ------------------- | if | VrId | IP | RowStat | +----+------+-------+---------+ | | | | | | I1 | 01 | A | active | | | | | | +----+------+-------+---------+ | | | | | | I1 | 02 | B | active | | | | | | +----+------+-------+---------+ draft-ietf-vrrp-mib-09.txt [Page 7] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 ----- MIB Tables For VRRP Router "IP B": ----- vrrpOperTable ------------- | if | VrId | State | Prior | AddrCnt | IpAddr | ... | RowStat | +----+------+-------+-------+---------+--------+-( )-+---------+ | | | | | | | | | | I2 | 01 | B | 1-254 | 1 | A | | active | | | | | | | | | | +----+------+-------+-------+---------+--------+-( )-+---------+ | | | | | | | | | | I2 | 02 | M | 255 | 1 | B | | active | | | | | | | | | | +----+------+-------+-------+---------+--------+-( )-+---------+ vrrpAssoIpAddrTable ------------------- | if | VrId | IP | RowStat | +----+------+-------+---------+ | | | | | | I2 | 01 | A | active | | | | | | +----+------+-------+---------+ | | | | | | I2 | 02 | B | active | | | | | | +----+------+-------+---------+ NOTES: 1) "I1" and "I2" are used to designate IF indices on each respective router. 2) For "State": M = Master; B = Backup. 3) In the vrrpOperTable, a "priority" of 255 indicates that the respective router owns the IP address, e.g., this IP address is native to the router (i.e., "the IP Address Owner" [17]). 2.4.2. VRRP Scenario #2 The following figure shows a simple network with two virtual routers. Here, a single interface has been configured with two IP addresses. Again, addresses in () indicate the IP address of the default gateway for a given host, H1 - H2. draft-ietf-vrrp-mib-09.txt [Page 8] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 VRID=1 VRID=2 +-----+ +-----+ | MR1 | | MR2 | | & | | & | | BR2 | | BR1 | +-----+ +-----+ IP A ---------->* *<---------- IP B IP C | | Interface=I2 Interface=I1 | | | | | | ------------------+------------+-----+--------+ ^ ^ | | (IP A) (IP B) | | +--+--+ +--+--+ | H1 | | H2 | +-----+ +-----+ ----- MIB Tables For VRRP Router "IP A": ----- vrrpOperTable ------------- | if | VrId | State | Prior | AddrCnt | IpAddr | ... | RowStat | +----+------+-------+-------+---------+--------+-( )-+---------+ | | | | | | | | | | I1 | 01 | M | 255 | 2 | A | | active | | | | | | | | | | +----+------+-------+-------+---------+--------+-( )-+---------+ | | | | | | | | | | I1 | 02 | B | 1-254 | 1 | B | | active | | | | | | | | | | +----+------+-------+-------+---------+--------+-( )-+---------+ draft-ietf-vrrp-mib-09.txt [Page 9] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 vrrpAssoIpAddrTable ------------------- | if | VrId | IP | RowStat | +----+------+-------+---------+ | | | | | | I1 | 01 | A | active | | | | | | +----+------+-------+---------+ | | | | | | I1 | 01 | C | active | | | | | | +----+------+-------+---------+ | | | | | | I1 | 02 | B | active | | | | | | +----+------+-------+---------+ ----- MIB Tables For VRRP Router "IP B": ----- vrrpOperTable ------------- | if | VrId | State | Prior | AddrCnt | IpAddr | ... | RowStat | +----+------+-------+-------+---------+--------+-( )-+---------+ | | | | | | | | | | I2 | 01 | B | 1-254 | 2 | A | | active | | | | | | | | | | +----+------+-------+-------+---------+--------+-( )-+---------+ | | | | | | | | | | I2 | 02 | M | 255 | 1 | B | | active | | | | | | | | | | +----+------+-------+-------+---------+--------+-( )-+---------+ draft-ietf-vrrp-mib-09.txt [Page 10] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 vrrpAssoIpAddrTable ------------------- | if | VrId | IP | RowStat | +----+------+-------+---------+ | | | | | | I2 | 01 | A | active | | | | | | +----+------+-------+---------+ | | | | | | I2 | 01 | C | active | | | | | | +----+------+-------+---------+ | | | | | | I2 | 02 | B | active | | | | | | +----+------+-------+---------+ draft-ietf-vrrp-mib-09.txt [Page 11] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 3. Definitions VRRP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, Integer32, IpAddress, mib-2 FROM SNMPv2-SMI TEXTUAL-CONVENTION, RowStatus, MacAddress, TruthValue, TimeStamp FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ifIndex FROM IF-MIB; vrrpMIB MODULE-IDENTITY LAST-UPDATED "9910050900Z" ORGANIZATION "IETF VRRP Working Group" CONTACT-INFO "Brian R. Jewell Postal: 3Com Corporation 5400 BayFront Plaza Santa Clara, California 95052 Tel: +1 408 326 6173 E-Mail: bjewell@3com.com" DESCRIPTION "This MIB describes objects used for managing Virtual Router Redundancy Protocol (VRRP) routers." REVISION "9910050900Z" -- 05 Oct 1999 DESCRIPTION "Initial version as published in RFC xxxx (number to be assigned)." ::= { mib-2 68 } draft-ietf-vrrp-mib-09.txt [Page 12] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 -- ******************************************************************* -- Textual Conventions -- ******************************************************************* VrId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A number which, along with an interface index (ifIndex), serves to uniquely identify a virtual router on a given VRRP router. A set of one or more associated addresses is assigned to a VRID." SYNTAX Integer32 (1..255) -- ******************************************************************* -- VRRP MIB Groups -- ******************************************************************* vrrpOperations OBJECT IDENTIFIER ::= { vrrpMIB 1 } vrrpStatistics OBJECT IDENTIFIER ::= { vrrpMIB 2 } vrrpConformance OBJECT IDENTIFIER ::= { vrrpMIB 3 } -- ******************************************************************* -- Start of MIB objects -- ******************************************************************* vrrpNodeVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value identifies the particular version of the VRRP supported by this node." ::= { vrrpOperations 1 } vrrpNotificationCntl OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether the VRRP-enabled router will generate SNMP traps for events defined in this MIB. 'Enabled' results in SNMP traps; 'disabled', no traps are sent." DEFVAL { enabled } ::= { vrrpOperations 2 } draft-ietf-vrrp-mib-09.txt [Page 13] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 -- ******************************************************************* -- VRRP Operations Table -- ******************************************************************* vrrpOperTable OBJECT-TYPE SYNTAX SEQUENCE OF VrrpOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of 'vrrpOperEntry' items." ::= { vrrpOperations 3 } vrrpOperEntry OBJECT-TYPE SYNTAX VrrpOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the vrrpOperTable containing the operational characteristics of a virtual router. On a VRRP router, a given virtual router is identified by a combination of the IF index and VRID. Rows in the table cannot be modified unless the value of `vrrpOperAdminState' is `disabled' and the `vrrpOperState' has transitioned to `initialize'." INDEX { ifIndex, vrrpOperVrId } ::= { vrrpOperTable 1 } draft-ietf-vrrp-mib-09.txt [Page 14] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 VrrpOperEntry ::= SEQUENCE { vrrpOperVrId VrId, vrrpOperVirtualMacAddr MacAddress, vrrpOperState INTEGER, vrrpOperAdminState INTEGER, vrrpOperPriority Integer32, vrrpOperIpAddrCount Integer32, vrrpOperMasterIpAddr IpAddress, vrrpOperPrimaryIpAddr IpAddress, vrrpOperAuthType INTEGER, vrrpOperAuthKey OCTET STRING, vrrpOperAdvertisementInterval Integer32, vrrpOperPreemptMode TruthValue, vrrpOperVirtualRouterUpTime TimeStamp, vrrpOperProtocol INTEGER, vrrpOperRowStatus RowStatus } vrrpOperVrId OBJECT-TYPE SYNTAX VrId MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object contains the Virtual Router Identifier (VRID)." ::= { vrrpOperEntry 1 } draft-ietf-vrrp-mib-09.txt [Page 15] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 vrrpOperVirtualMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The virtual MAC address of the virtual router. Although this object can be derived from the 'vrrpOperVrId' object, it is defined so that it is easily obtainable by a management application and can be included in VRRP-related SNMP traps." ::= { vrrpOperEntry 2 } vrrpOperState OBJECT-TYPE SYNTAX INTEGER { initialize(1), backup(2), master(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current state of the virtual router. This object has three defined values: - `initialize', which indicates that all the virtual router is waiting for a startup event. - `backup', which indicates the virtual router is monitoring the availability of the master router. - `master', which indicates that the virtual router is forwarding packets for IP addresses that are associated with this router. Setting the `vrrpOperAdminState' object (below) initiates transitions in the value of this object." ::= { vrrpOperEntry 3 } draft-ietf-vrrp-mib-09.txt [Page 16] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 vrrpOperAdminState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object will enable/disable the virtual router function. Setting the value to `up', will transition the state of the virtual router from `initialize' to `backup' or `master', depending on the value of `vrrpOperPriority'. Setting the value to `down', will transition the router from `master' or `backup' to `initialize'. State transitions may not be immediate; they sometimes depend on other factors, such as the interface (IF) state. The `vrrpOperAdminState' object must be set to `down' prior to modifying the other read-create objects in the conceptual row. The value of the `vrrpOperRowStatus' object (below) must be `active', signifying that the conceptual row is valid (i.e., the objects are correctly set), in order for this object to be set to `up'." DEFVAL { down } ::= { vrrpOperEntry 4 } draft-ietf-vrrp-mib-09.txt [Page 17] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 vrrpOperPriority OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the priority to be used for the virtual router master election process. Higher values imply higher priority. A priority of '0', although not settable, is sent by the master router to indicate that this router has ceased to particpate in VRRP and a backup virtual router should transition to become a new master. A priority of 255 is used for the router that owns the associated IP address(es)." DEFVAL { 100 } ::= { vrrpOperEntry 5 } vrrpOperIpAddrCount OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IP addresses that are associated with this virtual router. This number is equal to the number of rows in the vrrpAssoIpAddrTable that correspond to a given IF index/VRID pair." ::= { vrrpOperEntry 6 } vrrpOperMasterIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The master router's real (primary) IP address. This is the IP address listed as the source in VRRP advertisement last received by this virtual router." ::= { vrrpOperEntry 7 } draft-ietf-vrrp-mib-09.txt [Page 18] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 vrrpOperPrimaryIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "In the case where there is more than one IP address for a given `ifIndex', this object is used to specify the IP address that will become the `vrrpOperMasterIpAddr', should the virtual router transition from backup to master. If this object is set to 0.0.0.0, the IP address which is numerically lowest will be selected." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { vrrpOperEntry 8 } vrrpOperAuthType OBJECT-TYPE SYNTAX INTEGER { noAuthentication(1), -- VRRP protocol exchanges are not -- authenticated. simpleTextPassword(2), -- Exchanges are authenticated by a -- clear text password. ipAuthenticationHeader(3) -- Exchanges are authenticated using -- the IP authentication header. } MAX-ACCESS read-create STATUS current DESCRIPTION "Authentication type used for VRRP protocol exchanges between virtual routers. This value of this object is the same for a given ifIndex." DEFVAL { noAuthentication } ::= { vrrpOperEntry 9 } vrrpOperAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The Authentication Key. This object is set according to the value of the 'vrrpOperAuthType' object ('simpleTextPassword' or 'ipAuthenticationHeader'). If the length of the value is less than 16 octets, the agent will left adjust and zero fill to 16 octets. The value of this object is the same for a given ifIndex. When read, vrrpOperAuthKey always returns an Octet String of length zero." ::= { vrrpOperEntry 10 } draft-ietf-vrrp-mib-09.txt [Page 19] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 vrrpOperAdvertisementInterval OBJECT-TYPE SYNTAX Integer32 (1..255) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The time interval, in seconds, between sending advertisement messages. Only the master router sends VRRP advertisements." DEFVAL { 1 } ::= { vrrpOperEntry 11 } vrrpOperPreemptMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Controls whether a higher priority virtual router will preempt a lower priority master." DEFVAL { true } ::= { vrrpOperEntry 12 } vrrpOperVirtualRouterUpTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This is the value of the `sysUpTime' object when this virtual router (i.e., the `vrrpOperState') transitioned out of `initialized'." ::= { vrrpOperEntry 13 } vrrpOperProtocol OBJECT-TYPE SYNTAX INTEGER { ip (1), bridge (2), decnet (3), other (4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The particular protocol being controlled by this Virtual Router." DEFVAL { ip } ::= { vrrpOperEntry 14 } draft-ietf-vrrp-mib-09.txt [Page 20] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 vrrpOperRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status variable, used in accordance to installation and removal conventions for conceptual rows. The rowstatus of a currently active row in the vrrpOperTable is constrained by the operational state of the corresponding virtual router. When `vrrpOperRowStatus' is set to active(1), no other objects in the conceptual row, with the exception of `vrrpOperAdminState', can be modified. Prior to setting the `vrrpOperRowStatus' object from `active' to a different value, the `vrrpOperAdminState' object must be set to `down' and the `vrrpOperState' object be transitioned to `initialize'. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the `vrrpOperRowStatus' column will be read as notReady(3). In particular, a newly created row cannot be made active(1) until (minimally) the corresponding instance of `vrrpOperVrId' has been set and there is at least one active row in the `vrrpAssoIpAddrTable' defining an associated IP address for the virtual router." ::= { vrrpOperEntry 15 } -- ******************************************************************* -- VRRP Associated IP Address Table -- ******************************************************************* vrrpAssoIpAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF VrrpAssoIpAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of addresses associated with this virtual router." ::= { vrrpOperations 4 } draft-ietf-vrrp-mib-09.txt [Page 21] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 vrrpAssoIpAddrEntry OBJECT-TYPE SYNTAX VrrpAssoIpAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table contains an IP address that is associated with a virtual router. The number of rows for a given ifIndex and VrId will equal the number of IP addresses associated (e.g., backed up) by the virtual router (equivalent to 'vrrpOperIpAddrCount'). Rows in the table cannot be modified unless the value of `vrrpOperAdminState' is `disabled' and the `vrrpOperState' has transitioned to `initialize'." INDEX { ifIndex, vrrpOperVrId, vrrpAssoIpAddr } ::= { vrrpAssoIpAddrTable 1 } VrrpAssoIpAddrEntry ::= SEQUENCE { vrrpAssoIpAddr IpAddress, vrrpAssoIpAddrRowStatus RowStatus } vrrpAssoIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The assigned IP addresses that a virtual router is responsible for backing up." ::= { vrrpAssoIpAddrEntry 1 } draft-ietf-vrrp-mib-09.txt [Page 22] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 vrrpAssoIpAddrRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status variable, used according to installation and removal conventions for conceptual rows. Setting this object to active(1) or createAndGo(4) results in the addition of an associated address for a virtual router. Destroying the entry or setting it to notInService(2) removes the associated address from the virtual router. The use of other values is implementation-dependent." ::= { vrrpAssoIpAddrEntry 2 } -- ******************************************************************* -- VRRP Router Statistics -- ******************************************************************* vrrpRouterChecksumErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP packets received with an invalid VRRP checksum value." ::= { vrrpStatistics 1 } vrrpRouterVersionErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP packets received with an unknown or unsupported version number." ::= { vrrpStatistics 2 } vrrpRouterVrIdErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP packets received with an invalid VRID for this virtual router." ::= { vrrpStatistics 3 } draft-ietf-vrrp-mib-09.txt [Page 23] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 -- ******************************************************************* -- VRRP Router Statistics Table -- ******************************************************************* vrrpRouterStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF VrrpRouterStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of virtual router statistics." ::= { vrrpStatistics 4 } vrrpRouterStatsEntry OBJECT-TYPE SYNTAX VrrpRouterStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing statistics information about a given virtual router." AUGMENTS { vrrpOperEntry } ::= { vrrpRouterStatsTable 1 } draft-ietf-vrrp-mib-09.txt [Page 24] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 VrrpRouterStatsEntry ::= SEQUENCE { vrrpStatsBecomeMaster Counter32, vrrpStatsAdvertiseRcvd Counter32, vrrpStatsAdvertiseIntervalErrors Counter32, vrrpStatsAuthFailures Counter32, vrrpStatsIpTtlErrors Counter32, vrrpStatsPriorityZeroPktsRcvd Counter32, vrrpStatsPriorityZeroPktsSent Counter32, vrrpStatsInvalidTypePktsRcvd Counter32, vrrpStatsAddressListErrors Counter32, vrrpStatsInvalidAuthType Counter32, vrrpStatsAuthTypeMismatch Counter32, vrrpStatsPacketLengthErrors Counter32 } vrrpStatsBecomeMaster OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times that this virtual router's state has transitioned to MASTER." ::= { vrrpRouterStatsEntry 1 } vrrpStatsAdvertiseRcvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP advertisements received by this virtual router." ::= { vrrpRouterStatsEntry 2 } draft-ietf-vrrp-mib-09.txt [Page 25] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 vrrpStatsAdvertiseIntervalErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP advertisement packets received for which the advertisement interval is different than the one configured for the local virtual router." ::= { vrrpRouterStatsEntry 3 } vrrpStatsAuthFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP packets received that do not pass the authentication check." ::= { vrrpRouterStatsEntry 4 } vrrpStatsIpTtlErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP packets received by the virtual router with IP TTL (Time-To-Live) not equal to 255." ::= { vrrpRouterStatsEntry 5 } vrrpStatsPriorityZeroPktsRcvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP packets received by the virtual router with a priority of '0'." ::= { vrrpRouterStatsEntry 6 } vrrpStatsPriorityZeroPktsSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VRRP packets sent by the virtual router with a priority of '0'." ::= { vrrpRouterStatsEntry 7 } draft-ietf-vrrp-mib-09.txt [Page 26] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 vrrpStatsInvalidTypePktsRcvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of VRRP packets received by the virtual router with an invalid value in the 'type' field." ::= { vrrpRouterStatsEntry 8 } vrrpStatsAddressListErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received for which the address list does not match the locally configured list for the virtual router." ::= { vrrpRouterStatsEntry 9 } vrrpStatsInvalidAuthType OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with an unknown authentication type." ::= { vrrpRouterStatsEntry 10 } vrrpStatsAuthTypeMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with 'Auth Type' not equal to the locally configured authentication method (`vrrpOperAuthType')." ::= { vrrpRouterStatsEntry 11 } vrrpStatsPacketLengthErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a packet length less than the length of the VRRP header." ::= { vrrpRouterStatsEntry 12 } draft-ietf-vrrp-mib-09.txt [Page 27] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 -- ******************************************************************* -- Trap Definitions -- ******************************************************************* vrrpNotifications OBJECT IDENTIFIER ::= { vrrpMIB 0 } vrrpTrapPacketSrc OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The IP address of an inbound VRRP packet. Used by vrrpTrapAuthFailure trap." ::= { vrrpOperations 5 } vrrpTrapAuthErrorType OBJECT-TYPE SYNTAX INTEGER { invalidAuthType (1), authTypeMismatch (2), authFailure (3) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Potential types of configuration conflicts. Used by vrrpAuthFailure trap." ::= { vrrpOperations 6 } vrrpTrapNewMaster NOTIFICATION-TYPE OBJECTS { vrrpOperMasterIpAddr } STATUS current DESCRIPTION "The newMaster trap indicates that the sending agent has transitioned to 'Master' state." ::= { vrrpNotifications 1 } draft-ietf-vrrp-mib-09.txt [Page 28] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 vrrpTrapAuthFailure NOTIFICATION-TYPE OBJECTS { vrrpTrapPacketSrc, vrrpTrapAuthErrorType } STATUS current DESCRIPTION "A vrrpAuthFailure trap signifies that a packet has been received from a router whose authentication key or authentication type conflicts with this router's authentication key or authentication type. Implementation of this trap is optional." ::= { vrrpNotifications 2 } -- ******************************************************************* -- Conformance Information -- ******************************************************************* vrrpMIBCompliances OBJECT IDENTIFIER ::= { vrrpConformance 1 } vrrpMIBGroups OBJECT IDENTIFIER ::= { vrrpConformance 2 } -- ................................................................... -- Compliance Statements -- ................................................................... vrrpMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The core compliance statement for all VRRP implementations." MODULE -- this module MANDATORY-GROUPS { vrrpOperGroup, vrrpStatsGroup } OBJECT vrrpOperPriority WRITE-SYNTAX Integer32 (1..255) DESCRIPTION "SETable values are from 1 to 255." ::= { vrrpMIBCompliances 1 } draft-ietf-vrrp-mib-09.txt [Page 29] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 -- ................................................................... -- Conformance Groups -- ................................................................... vrrpOperGroup OBJECT-GROUP OBJECTS { vrrpNodeVersion, vrrpNotificationCntl, vrrpOperVirtualMacAddr, vrrpOperState, vrrpOperAdminState, vrrpOperPriority, vrrpOperIpAddrCount, vrrpOperMasterIpAddr, vrrpOperPrimaryIpAddr, vrrpOperAuthType, vrrpOperAuthKey, vrrpOperAdvertisementInterval, vrrpOperPreemptMode, vrrpOperVirtualRouterUpTime, vrrpOperProtocol, vrrpOperRowStatus, vrrpAssoIpAddrRowStatus } STATUS current DESCRIPTION "Conformance group for VRRP operations." ::= { vrrpMIBGroups 1 } draft-ietf-vrrp-mib-09.txt [Page 30] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 vrrpStatsGroup OBJECT-GROUP OBJECTS { vrrpRouterChecksumErrors, vrrpRouterVersionErrors, vrrpRouterVrIdErrors, vrrpStatsBecomeMaster, vrrpStatsAdvertiseRcvd, vrrpStatsAdvertiseIntervalErrors, vrrpStatsAuthFailures, vrrpStatsIpTtlErrors, vrrpStatsPriorityZeroPktsRcvd, vrrpStatsPriorityZeroPktsSent, vrrpStatsInvalidTypePktsRcvd, vrrpStatsAddressListErrors, vrrpStatsInvalidAuthType, vrrpStatsAuthTypeMismatch, vrrpStatsPacketLengthErrors } STATUS current DESCRIPTION "Conformance group for VRRP statistics." ::= { vrrpMIBGroups 2 } vrrpTrapGroup OBJECT-GROUP OBJECTS { vrrpTrapPacketSrc, vrrpTrapAuthErrorType } STATUS current DESCRIPTION "Conformance group for objects contained in VRRP notifications." ::= { vrrpMIBGroups 3 } vrrpNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { vrrpTrapNewMaster, vrrpTrapAuthFailure } STATUS current DESCRIPTION "The VRRP MIB Notification Group." ::= { vrrpMIBGroups 4 } END draft-ietf-vrrp-mib-09.txt [Page 31] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 4. Security Considerations There are a number of management objects defined in this MIB that have a MAX-ACCESS clause of read-write or read-create. Such objects may be considered sensitive or vulnerable to security attacks in some networking environments. The support for SET operations in a non- secure environment without proper protection can have a negative effect on VRRP router operations. A number of objects in the vrrpOperTable possess the read-create attribute. Manipulation of these objects is capable of affecting the operation of a virtual router. Specific examples of this include, but are not limited to: o The vrrpOperAdminState object which could be used to disable a virtual router. o The vrrpOperPrimaryIpAddr object which, if compromised, could allow assignment of an invalid IP address to a master router. o The authentication type/key related objects which could potentially render the VRRP security mechanisms ineffective. Of additional concern is the ability to disable the transmission of traps. This would nullify the capability of a virtual router to provide notification in the event of an authentication failure. SNMPv1 by itself is not a secure environment. Even if the network itself is secure (for example by using IPSec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB. It is recommended that the implementers consider the security features as provided by the SNMPv3 framework. Specifically, the use of the User-based Security Model RFC 2574 [RFC2574] and the View- based Access Control Model RFC 2575 [RFC2575] is recommended. It is then a customer/user responsibility to ensure that the SNMP entity giving access to an instance of this MIB, is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. draft-ietf-vrrp-mib-09.txt [Page 32] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 5. Acknowledgements The authors would like to thank Danny Mitzel, Venkat Prasad, Al Pham, Robert Hinden, Venkat Prasad, Barbera Denny, Fred Baker, Jeff Case, Flavio Fernandes, Acee Lindem, Scott Barvick, and Bert Wijnen for their comments and suggestions. 6. References [1] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for Describing SNMP Management Frameworks", RFC 2571, Cabletron Systems, Inc., BMC Software, Inc., IBM T. J. Watson Research, April 1999 [2] Rose, M., and K. McCloghrie, "Structure and Identification of Management Information for TCP/IP-based Internets", RFC 1155, STD 16, Performance Systems International, Hughes LAN Systems, May 1990 [3] Rose, M., and K. McCloghrie, "Concise MIB Definitions", RFC 1212, STD 16, Performance Systems International, Hughes LAN Systems, March 1991 [4] M. Rose, "A Convention for Defining Traps for use with the SNMP", RFC 1215, Performance Systems International, March 1991 [5] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M., and S. Waldbusser, "Structure of Management Information Version 2 (SMIv2)", RFC 2578, STD 58, Cisco Systems, SNMPinfo, TU Braunschweig, SNMP Research, First Virtual Holdings, International Network Services, April 1999 [6] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M., and S. Waldbusser, "Textual Conventions for SMIv2", RFC 2579, STD 58, Cisco Systems, SNMPinfo, TU Braunschweig, SNMP Research, First Virtual Holdings, International Network Services, April 1999 [7] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M., and S. Waldbusser, "Conformance Statements for SMIv2", RFC 2580, STD 58, Cisco Systems, SNMPinfo, TU Braunschweig, SNMP Research, First Virtual Holdings, International Network Services, April 1999 [8] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network Management Protocol", RFC 1157, STD 15, SNMP Research, Performance Systems International, Performance Systems International, MIT Laboratory for Computer Science, May 1990. draft-ietf-vrrp-mib-09.txt [Page 33] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 [9] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Introduction to Community-based SNMPv2", RFC 1901, SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. [10] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1906, SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. [11] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)", RFC 2572, SNMP Research, Inc., Cabletron Systems, Inc., BMC Software, Inc., IBM T. J. Watson Research, April 1999 [12] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", RFC 2574, IBM T. J. Watson Research, April 1999 [13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1905, SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. [14] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC 2573, SNMP Research, Inc., Secure Computing Corporation, Cisco Systems, April 1999 [15] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", RFC 2575, IBM T. J. Watson Research, BMC Software, Inc., Cisco Systems, Inc., April 1999 [16] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction to Version 3 of the Internet-standard Network Management Framework", RFC 2570, SNMP Research, Inc., TIS Labs at Network Associates, Inc., Ericsson, Cisco Systems, April 1999 [17] Knight, S., Weaver, D., Whipple, D., Hinden, R., Mitzel, D., Hunt, P., Higginson, P., Shand, M., Lindem, A., "Virtual Router Redundancy Protocol", RFC 2338. [18] McCloghrie, K., and F. Kastenholz, "The Interfaces Group MIB using SMIv2", RFC 2233, Cisco Systems, November 1997. draft-ietf-vrrp-mib-09.txt [Page 34] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 7. Authors' Addresses Brian R. Jewell 3Com, Inc. 5400 Bayfront Plaza Santa Clara, CA 95052 US Phone: +1 326 764 6173 EMail: bjewell@3com.com David Chuang 3Com, Inc. 5400 Bayfront Plaza Santa Clara, CA 95052 US Phone: +1 408 326 6610 EMail: david_chuang@3com.com 8. Intellectural Property Statement The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards- related documentation can be found in BCP-11. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementors or users of this specification can be obtained from the IETF Secretariat. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director. draft-ietf-vrrp-mib-09.txt [Page 35] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 9. Full Copyright Statement Copyright (C) The Internet Society (1999). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implmentation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. draft-ietf-vrrp-mib-09.txt [Page 36] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 -- ------------------------------------------------------------------- -- Change Log -- ------------------------------------------------------------------- NOTE TO RFC EDITOR: This section tracks changes made during revisions of this document. It should be deleted when the document is published as an RFC. * Aug/Sept/Oct 1999: Changes in 9th rev. (draft-ietf-vrrp-mib-09.txt): - Changed description for "vrrpTrapNewMaster" object. - Removed the "ifIndex" and "vrrpOperVrId" objects from the "vrrpTrapNewMaster" trap. This is because these objects are already present in the trap in the form of table indices. The "vrrpOperMasterIpAddr" object has replaced these in the trap. - As above, removed the "ifIndex" and "vrrpOperVrId" objects from the "vrrpTrapAuthFailure" trap. - Changed the DESCRIPTION clause of the MODULE-IDENTITY statement. - Added REVISION and secondary DESCRIPTION clauses to MODULE- IDENTITY macro. - Removed REFERENCE and DEFVAL clauses from the definition of the "vrrpNodeVersion" object. - Added IMPORT for NOTIFICATION-GROUP. - Since last sub ID of trap must be 0 (RFC2578), "vrrp- Notifications" has been redefined as {vrrpMIB 0} and traps defined directly under it. As per this change, the "vrrpTraps" object has been eliminated. Definition of the vrrpNotifications object was also moved to the "Trap Definitions" section of the MIB. - Both the "vrrpOperVrId" and "vrrpOperAssoIpAddr" were removed from the "vrrpOperGroup" definition. Since these are both not-accessible objects, this eliminates MIB compiler warnings. - Added new "vrrpNotificationGroup" NOTIFICATION-GROUP which contains the VRRP MIB traps. - Added WRITE-SYNTAX for "vrrpOperPriority" in Conformance section. This excludes setting of '0'. - Added UNITS clause to "vrrpOperAdvertisementInterval" - Changed (or removed) "SNMPv2" references to "SMIv2". - In section 2.1, changed bullet item from "traps" to "notifications". - In section 2.2, changed "IF Index" to ifIndex". - Changed label in MODULE-IDENTITY from "vrrp" to "vrrpMIB". - Added required Intellectual Property Statement (Section 8) and a Full Copyright Statement (Section 9). - Renamed "vrrpTrapsCntl" to "vrrpNotificationCntl" for consistancy with recent RFC's. - ------- - Removed redundant "vrrpMIB" definition (after MODULE-IDENTITY statement) that was causing compile errors. draft-ietf-vrrp-mib-09.txt [Page 37] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 - Removed "{}" from WRITE-SYNTAX of "vrrpMIBCompliance", as this was causing compile errors. - Added " vrrpTrapGroup" definition to contain objects used exclusively in VRRP traps. This eliminates compiler warnings. - Reference #18 (RFC1213 - IF MIB) was removed, as RFC 2233 has obsoleted it. - Reference #22 ("Instructions to RFC Authors") was removed. - Rewrote to DESCRIPTION for "vrrpOperRowStatus" to eliminate redundant wording that can be found in the RowStatus TC (RFC2579). - Added text to the DESCRIPTION of the "vrrpOperAdminState" explaining how it is decided whether to transition a VR to "backup" or "master". - ------- - Removed references [18], [19], [20] (RFC1902, RFC 1903, RFC 1904, respectively), as these have been obsoleted by newer documents. Reference [21] was renumbered to [18], accordingly. - Changed reference from [18] to [5], as per aforementioned change. - Changed reference to "MIB-II" to "IF-MIB". - Moved the OIDs for the "vrrpTrapPacketSrc" and "vrrpTrapAuthErrorType" objects under the "vrrpOperations" (vrrp 1) branch. This is to distinguish the OIDs of these objects from the "vrrpNotifications" OIDs. As part of this change, the OIDs for the two VRRP notifications were decremented accordingly. - Added disclaimer to Overview section regarding that IP addresses in this MIB are IPv4 specific and will not be compatible in an IPv6 environment. * June 1999: Changes in 8th revision (draft-ietf-vrrp-mib-08.txt): - Changed inport of "ifIndex" from RFC 1213 to IF-MIB. - Added new IANA assigned MIB OID (68). * June 1999: Changes in 7th revision (draft-ietf-vrrp-mib-07.txt): - Added MIB Boilerplate for "The SNMP Management Framework" section. - Added "Security Considerations" section - Removed references to "SNMPv2" in header and footers. * May, 1999: Changes in 6th revision (draft-ietf-vrrp-mib-06.txt): - Removed description of how "vrrpOperVirtualMacAddr" is specifed draft-ietf-vrrp-mib-09.txt [Page 38] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 as per changes to the VRRP Spec (addition of Token Ring). - Added citiations for RFC 1903 and RFC 1904 in references. - Modifed reference to RFC 1573, which has been obsoleted by RFC 2233. * March, 1999: Changes in 5th revision (draft-ietf-vrrp-mib-05.txt): - Objects under "vrrpRouterStatsEntry" were renumbered. OID's became out-of-sequence due to changes made in the last revision (04). - Format of section numbers was changed ('.' added) to be consistant with other RFC's. - Changed the type of "vrrpNodeVersion" from INTEGER to Integer32. Also made DEFVAL (for this object) a decimal number. - A few spelling and typographical corrections were made. - Revisions were made to the format of some of the references to make then more concise and consistant. - Reworded the Overview section to attempt to make the description of VRRP more in-line with the VRRP RFC. * January, 1999: Changes in 4th revision (draft-ietf-vrrp-mib-04.txt): - "vrrpNodeVersion" SYNTAX changed from OCTET STRING to INTEGER. - Removed the REFERENCE clause from "vrrpOperVirtualMacAddr", as it was deemed redundant. - The range of vrrpOperAddrCount was changed from (1..255) to (0..255). This reflects the fact that a row might be created in the vrrpOperTable *prior* to creating a row in the vrrpAssoIpAddrTable. - Removed DEFVAL clause from "vrrpOperAuthKey" as unnecessary. - Moved the following objects out of the "vrrpRouterStatsTable" to become "global" VRRP router objects: "vrrpStatsChecksunErrors", "vrrpStatsVersionErrors", "vrrpStatsVrIdErrors". Each of these was renamed "vrrpRouter*", accordingly (since they are no longer members of the vrrpRouterStatsTable. The reason for this change is that, when any of these events occur, attempting to map the packet, with possible corruption of the VRID (or other fields), into a row of the vrrpRouterStatsTable would be risky, at best. - Removed "vrrpOperVirtualMacAddr" from the "vrrpTrapNewMaster". Since the virtual MAC can be derived from the VR ID, this was extra payload in the trap. - removed "vrrpTrapConfigErrorType" and "vrrpTrapPacketSrc" from conformance groups, as these are not mandatory objects. - Added new object, "vrrpOperPrimaryIpAddr" to vrrpOperTable. This object allows for designation of the vrrp IP primary address on an interface with multiple IP addresses, should this draft-ietf-vrrp-mib-09.txt [Page 39] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 virtual router transition from backup to master. - Changed vrrpRouterStatsEntry to AUGMENT the vrrpOperEntry, since there is a one-to-one correspondence between these two objects and they are indexed with identical parmeters. - Addded new object, vrrpStatsPacketLengthErrors, to the statistics table. - Changed the description for "vrrpStatsSecurityViolations" to apply to *all* types of authentication failures, as opposed to cleartext auth failures only, which it previously stated. - Renamed "vrrpTrapConfigErrorType" object to "vrrpTrapAuthErrorType" and added a new enumeration for "authentication failures". - Renamed "vrrpStatsAuthTypeErrors" to "vrrpStatsAuthTypeMismatch". - Renamed "vrrpStatsSecurityViolations" to " vrrpStats- AuthenticationFailures" * November, 1998: Changes in 3rd revision (draft-ietf-vrrp-mib-03.txt): - Changed name of "vrrpAssoIpAddrStatus" object to "vrrpAssoIpAddrRowStatus" for consistancy with similar object in vrrpOperTable. - Changed name of "vrrpOperControl" object to "vrrpOperAdminState" and enhanced description clause. - Renumbered the objects in both the vrrpOperTable and vrrpAssoIpAddrTable. The first objects in the tables started with an OID of '2', when they should have started with '1'. - Changed the name of "vrrpStatsUnknownAuthType" to "vrrpStatsInvalidAuthType" as per suggestion that it was more concise. - Rewrote the descriptions for the table Entry objects and the rowstatus objects to make the process of row creation and deletion more clear. Each enumeration of the rowstatus object in the "vrrpOperTable" is now clearly explained. - Changed MAX-ACCESS to "read-create" on the "vrrpOperAuthType" and "vrrpOperAuthKey" objects. This was done with the assumption the the VRRP RFC will change to make these attributes defined on a "per-virtual-router-basis" as was proposed at the August (1998) IETF Meeting. * July, 1998: Changes in 2nd revision (draft-ietf-vrrp-mib-02.txt): - A number of changes were made to the textual content of the draft as per feedback received at the last WG meeting. These changes were too numerous to document individually in this section. - The size of the "vrrpNodeVersion" object has been changed from 2 octets to 1 octet. draft-ietf-vrrp-mib-09.txt [Page 40] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 - References to obsoleted RFC's have been replaced by references to later documents. Notably, references to RFC's 1442, 1443 and 1444 have been replaced by RFC 1902, RFC 1903 and RFC 1904, respectively. - The description for the "vrrpOperControl" was changed to reflect the fact that a virtual router does not necessarily transition directly from initialize state -> backup state. The description for the "vrrpStatsBecomeMaster" was also changed to more accurately convey this fact. - The SYNTAX of the "vrrpOperIpAddrCount" was changed to reflect the fact that a virtual router can support only up to 255 backup IP addresses. - Descriptions for vrrpOperAuthType and vrrpOperAuthKey expanded to indicate the per-interface assignment. - SYNTAX of vrrpOperPreemptMode object changed from INTEGER to 'truthValue' - The OIDs for the VRRP traps were fixed; incorrect ident- ifiers ('vrrpOperations') had been used in OID assignments. - The SYNTAX for the 'vrrpOperPriority' object was corrected to indicate that this can have a value of '0'. - The vrrpOperHMACMD5Key object was deleted. It was combined with the vrrpOperAuthKey object, whose SYNTAX was adjusted accordingly. - OID for 'vrrpTraps' changed to '{ vrrpNotifications 1 }' - The 'vrrpStatsPasswdSecurityViolations' and 'vrrpStatsHmac- SecurityViolations' objects have been combined into a single 'vrrpStatsSecurityViolations' object; this was suggested to avoid redundancy. - As per the last WG meeting, the 'vrrpAssoIpAddrIndex' object has been deleted from the 'vrrpAssoIpAddrTable'and replaced by 'vrrpAssoIpAddr'. - Removed references to 'vrrpAssoIpAddrIndex' in samples. - Added new object 'vrrpOperProtocol' to 'VrrpOperEntry'. - MAX-ACCESS for the 'vrrpOperVrId' object changed to 'not-accessible', as per RFC1902 (auxilary objects). - SYNTAX for 'vrrpOperVirtualRouterUpTime' changed to 'TimeStamp'. - Added importation of 'TruthValue'and 'TimeStamp' to accomodate changes listed above. Deleted importation of 'TimeTicks'. - Changed MAX-ACCESS to 'accessible-for-notify' for 'vrrpTrapPacketSrc' and 'vrrpTrapConfigErrorType' objects. - In the sample tables, the "if" values were incorrect for the sample tables for "IP B" (they used to read "I1"). - MAX-ACCESS for 'vrrpOperAuthType' and 'vrrpOperAuthKey' changed to 'read-only', since these objects are defined on a per-interface basis. - Overall review and editing of Section 5.0 (References) with deletion of references not used in this document. Also, added draft-ietf-vrrp-mib-09.txt [Page 41] INTERNET-DRAFT VRRP MIB Management Objects October 5, 1999 reference '9'. Concerns: --------- - Keep the 'vrrpTrapAuthFailure' trap? - Remove 'vrrpTrapPacketSrc' and 'vrrpTrapConfigErrorType' from compliances? Only used for 'vrrpTrapAuthFailure' trap. * 3/4/1998: Changes in 1st revision (draft-ietf-vrrp-mib-01.txt): - Overall review and editing of document text and object descriptions from feedback received at December 1997 IETF meeting. More specifically the changes made along these lines include the following: -- Cleaned up Section 5.0 ("References") and validated. -- Modifed diagram for VRRP Scenario #2 (Section 2.4.2). -- VRRP Overview (Section 2.0) rewritten to be more in-line with latest revision (05) of VRRP RFC Draft. -- Description of "VrId" Textual convention rewritten. - MAX-ACCESS of vrrpTrapCntl object changed to "read-write". - Changed SYNTAX of "vrrpOperVirtualMacAddr" object from "PhyAddress" to "MacAddress". - Changed the syntax of the "vrrpOperPriority" object so upper value can be 255. - Change MAX-ACCESS for "vrrpOperAuthType" object from read-only to read-create. - Added three new objects to "vrrpRouterStatsTable": "vrrpStatsAddressListErrors", "vrrpStatsUnknownAuthType" and "vrrpStatsAuthTypeErrors". - Removed "vrrpStatsUnknownPacketType" object, as it was redundant (with "vrrpStatsInvalidPacketType"). - Removed the "vrrpOperIfIndex" object to use "ifIndex" (which is actually equivalent) instead. * 11/19/97 (vft-ietf-vrrp-mib-00.txt) - Initial Draft draft-ietf-vrrp-mib-09.txt [Page 42]