Network Working Group Cheenu Srinivasan Internet Draft Tachion Networks, Inc. Expires: September 2001 Arun Viswanathan Force10 Networks, Inc. Thomas D. Nadeau Cisco Systems, Inc. March 2, 2001 MPLS Traffic Engineering Management Information Base Using SMIv2 draft-ietf-mpls-te-mib-06.txt Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Abstract This memo defines an experimental portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects for Multi-Protocol Label Switching (MPLS) [MPLSArch] based traffic engineering. 1. Introduction This memo defines an experimental portion of the Management Information Base (MIB) for use with network management Srinivasan et al. Expires September 2001 [Page 1] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 protocols in the Internet community. In particular, it describes managed objects for modeling a Multi-Protocol Label Switching (MPLS) [MPLSArch] based traffic engineering. This MIB should be used in conjunction with the companion document [LSRMIB] for MPLS based traffic engineering configuration and management. Comments should be made directly to the MPLS mailing list at mpls@uu.net. This memo does not, in its draft form, specify a standard for the Internet community. 2. Terminology This document uses terminology from the MPLS architecture document [MPLSArch] and MPLS Label Switch Router MIB [LSRMIB]. Some frequently used terms are described next. An explicitly routed LSP (ERLSP) is referred to as an MPLS tunnel. It consists of one in-segment and/or one out- segment at the ingress/egress LSRs, each segment being associated with one MPLS interface. These are also referred to as tunnel segments. Additionally, at an intermediate LSR, we model a connection as consisting of one or more in-segments and/or one or more out-segments. The binding or interconnection between in-segments and out- segments in performed using a cross-connect. These objects are defined in the MPLS Label Switch Router MIB [LSRMIB]. 3. The SNMP Management Framework The SNMP Management Framework presently consists of five major components: - An overall architecture, described in RFC 2271 [SNMPArch]. - Mechanisms for describing and naming objects and events for the purpose of management. The first version of this Structure of Management Information (SMI) is called SMIv1 and described in RFC 1155 [SMIv1], RFC 1212 [SNMPv1MIBDef] and RFC 1215 [SNMPv1Traps]. The second version, called SMIv2, is described in RFC 1902 [SMIv2], RFC 1903 [SNMPv2TC] and RFC 1904 [SNMPv2Conf]. - Message protocols for transferring management information. The first version of the SNMP message Srinivasan et al. Expires September 2001 [Page 2] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 protocol is called SNMPv1 and described in RFC 1157 [SNMPv1]. A second version of the SNMP message protocol, which is not an Internet standards track protocol, is called SNMPv2c and described in RFC 1901 [SNMPv2c] and RFC 1906 [SNMPv2TM]. The third version of the message protocol is called SNMPv3 and described in RFC 1906 [SNMPv2TM], RFC 2272 [SNMPv3MP] and RFC 2574 [SNMPv3USM]. - Protocol operations for accessing management information. The first set of protocol operations and associated PDU formats is described in RFC 1157 [SNMPv1]. A second set of protocol operations and associated PDU formats is described in RFC 1905 [SNMPv2PO]. - A set of fundamental applications described in RFC 2273 [SNMPv3App] and the view-based access control mechanism described in RFC 2575 [SNMPv3VACM]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the mechanisms defined in the SMI. This memo specifies a MIB module that is compliant to the SMIv2. A MIB conforming to the SMIv1 can be produced through the appropriate translations. The resulting translated MIB must be semantically equivalent, except where objects or events are omitted because no translation is possible (use of Counter64). Some machine- readable information in SMIv2 will be converted into textual descriptions in SMIv1 during the translation process. However, this loss of machine-readable information is not considered to change the semantics of the MIB. 3.1. Object Definitions Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the subset of Abstract Syntax Notation One (ASN.1) defined in the SMI. In particular, each object type is named by an OBJECT IDENTIFIER, an administratively assigned name. The object type together with an object instance serves to uniquely identify a specific instantiation of the object. For human convenience, we often use a textual string, termed the descriptor, to also refer to the object type. Srinivasan et al. Expires September 2001 [Page 3] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 4. Feature List The MPLS traffic engineering MIB is designed to satisfy the following requirements and constraints. - The MIB supports configuration of point-to-point unidirectional tunnels. - MPLS tunnels need not be interfaces, but it is possible to configure a tunnel as an interface. - The MIB supports manually configured MPLS tunnels as well as those set up via any MPLS signaling protocol. - The MIB supports persistent as well as non-persistent tunnels. 5. Outline Traffic engineering support for MPLS tunnels requires the following configuration. - Setting up MPLS tunnels along with appropriate configuration parameters. - Configuring tunnel loose and strict source routed hops. These actions may need to be accompanied with corresponding actions using [LSRMIB] to establish and configure tunnel segments, if this is done manually. Also, the in-segment and out-segment performance tables, mplsInSegmentPerfTable and mplsOutSegmentPerfTable [LSRMIB], should be used to determine performance of the tunnels and tunnel segments. 5.1. Summary of Traffic Engineering MIB The MIB objects for performing these actions consist of the following tables. - Tunnel table (mplsTunnelTable) for setting up MPLS tunnels. - Resource table (mplsTunnelResourceTable) for setting up the tunnel resources. - CRLDP resource table (mplsTunnelCRLDPResTable) for specifying resource objects applicable to tunnels signaled using CRLDP. Srinivasan et al. Expires September 2001 [Page 4] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 - Tunnel hop table (mplsTunnelHopTable) for configuring strict and loose source routed MPLS tunnels hops. When a tunnel is signaled via a MPLS signaling protocol, the mplsTunnelARHopTable gives the actual list of hops traversed by the tunnel as reported by the signaling protocol. These tables are described in the subsequent sections. 6. Brief Description of MIB Objects The objects described in this section support the functionality described in documents [RSVPTun][CR-LDP]. The tables support both manually configured and signaled tunnels. 6.1. mplsTunnelTable The mplsTunnelTable allows new MPLS tunnels to be created between an MPLS LSR and a remote endpoint, and existing tunnels to be reconfigured or removed. Note that we only support point-to-point tunnel segments, although multi- point-to-point and point-to-multi-point connections are supported by an LSR acting as a cross-connect. Each MPLS tunnel can thus have one out-segment originating at an LSR and/or one in-segment terminating at that LSR. mplsTunnelTable does not define the in and out segments forming the tunnel. Instead, these are defined by creating rows in the in-segment and out-segment tables, defining relationships in the cross-connect table and referring to these rows in the mplsTunnelTable using a cross-connect index, mplsTunnelXCIndex. These segment and cross-connect related objects are defined in [LSRMIB]. 6.2. mplsTunnelResourceTable mplsTunnelResourceTable is used to indicate the resources required for a tunnel. Multiple tunnels may share the same resources by pointing to the same entry in this table. Tunnels that do not share resources must point to separate entries in this table. 6.3. mplsTunnelHopTable Srinivasan et al. Expires September 2001 [Page 5] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 mplsTunnelHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsTunnelTable, when it is established via signaling. Multiple tunnels may share the same hops by pointing to the same entry in this table. Each row also has a secondary index, mplsTunnelHopIndex, corresponding to the next hop of this tunnel. The scalar mplsTunnelMaxHops indicates the maximum number of hops that can be specified on each tunnel supported by this LSR. 6.4. mplsTunnelARHopTable mplsTunnelARHopTable is used to indicate the actual hops traversed by a tunnel as reported by the MPLS signaling protocol after the tunnel is setup. The support of this table is optional since not all MPLS signaling protocol may support this feature. 6.5. mplsTunnelCHoptable mplsTunnelCHopTable lists the actual hops computed by a constraint-based routing algorithm based on the mplsTunnelHopTable. The support of this table is optional since not all implementations may support computation of hop list using a constraint-based routing protocol. 6.6. mplsTunnelPerfTable mplsTunnelPerfTable provides several counters to measure the performance of the MPLS tunnels. This table auguments mplsTunnelTable. 6.7. mplsTunnelCRLDPResTable mplsTunnelCRLDPResTable contains resource information for those tunnels that are signaled using CRLDP. This is a sparse extension to mplsTunnelResourceTable and is also indexed by mplsTunnelResourceIndex. As with mplsTunnelResourceTable, multiple tunnels may share the same resources by pointing to the same entry in this table. Tunnels that do not share resources must point to separate entries in this table. 7. Application of the Interface Group to MPLS Tunnels Srinivasan et al. Expires September 2001 [Page 6] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 The Interfaces Group of MIB II defines generic managed objects for managing interfaces. This memo contains the media-specific extensions to the Interfaces Group for managing MPLS Tunnels as logical interfaces. This memo assumes the interpretation of the Interfaces Group to be in accordance with [IFMIB] which states that the interfaces table (ifTable) contains information on the managed resource's interfaces and that each sub-layer below the internetwork layer of a network interface is considered an interface. Thus, the MPLS interface is represented as an entry in the ifTable. The interrelation of entries in the ifTable is defined by Interfaces Stack Group defined in [IFMIB]. When using MPLS Tunnels as interfaces, the interface stack table might appear as follows: +------------------------------------------------+ | MPLS-Tunnel-interface ifType = mplsTunnel(150) | +------------------------------------------------+ | MPLS-interface ifType = mpls(166) | +------------------------------------------------+ | Underlying Layer | +------------------------------------------------+ In the above diagram, "Underlying Layer" refers to the ifIndex of any interface type, which has been defined for MPLS interworking. Examples include ATM, Frame Relay, Ethernet, etc. 7.1. Support of the MPLS Tunnel Interface by ifTable Some specific interpretations of ifTable for those MPLS tunnels represented as interfaces follow: Object Use for the MPLS tunnel. ifIndex Each MPLS tunnel is represented by an ifEntry. ifDescr Description of the MPLS tunnel. ifType The value that is allocated for MPLS tunnel is 150. ifSpeed The total bandwidth in bits per second for use by the MPLS tunnel. Srinivasan et al. Expires September 2001 [Page 7] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 ifPhysAddress Unused. ifAdminStatus See [IFMIB]. ifOperStatus Assumes the value down(2) if the MPLS tunnel is down. ifLastChange See [IFMIB]. ifInOctets The number of octets received over the MPLS tunnel. ifOutOctets The number of octets transmitted over the MPLS tunnel. ifInErrors The number of labeled packets dropped due to uncorrectable errors. ifInUnknownProtos The number of received packets discarded during packet header validation, including packets with unrecognized label values. ifOutErrors See [IFMIB]. ifName Textual name (unique on this system) of the MPLS tunnel or an octet string of zero length. ifLinkUpDownTrapEnable Default is disabled (2). ifConnectorPresent Set to false (2). ifHighSpeed See [IFMIB]. ifHCInOctets The 64-bit version of ifInOctets; supported if required by the compliance statements in [IFMIB]. ifHCOutOctets The 64-bit version of ifOutOctets; supported if required by the compliance statements in [IFMIB]. ifAlias The non-volatile 'alias' name for the MPLS tunnel as specified by a network manager. Srinivasan et al. Expires September 2001 [Page 8] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 8. Example of Tunnel Setup This section contains an example of which MIB objects should be modified if one would like to create a best effort, loosely routed, unidirectional traffic engineered tunnel, which spans two hops of a simple network. Note that these objects should be created on the "head-end" LSR. In mplsTunnelTable: { mplsTunnelIndex = 1, mplsTunnelInstance = 1, mplsTunnelIngressLSRId = 123.123.125.1, mplsTunnelEgressLSRId = 123.123.126.1, mplsTunnelName = "My first tunnel", mplsTunnelDescr = "Here to there", mplsTunnelIsIf = true (1), mplsTunnelXCPointer = mplsXCIndex.2.0.0.15, mplsTunnelSignallingProto = none (1), mplsTunnelSetupPrio = 0, mplsTunnelHoldingPrio = 0, mplsTunnelSessionAttributes = 0, mplsTunnelOwner = snmp (1), mplsTunnelLocalProtectInUse = false (0), mplsTunnelResourcePointer = mplsTunnelResourceIndex.5, mplsTunnelInstancePriority = 1, mplsTunnelHopTableIndex = 1, mplsTunnelPrimaryInstance = 0, mplsTunnelIncludeAnyAffinity = 0, mplsTunnelIncludeAllAffinity = 0, mplsTunnelExcludeAllAffinity = 0, mplsTunnelPathInUse = 1, mplsTunnelRole = head(1), mplsTunnelRowStatus = createAndGo (4) } In mplsTunnelResourceTable: { mplsTunnelResourceIndex = 5, mplsTunnelResourceMaxRate = 0, mplsTunnelResourceMeanRate = 0, mplsTunnelResourceMaxBurstSize = 0, mplsTunnelResourceRowStatus = createAndGo (4) } The next two instances of mplsTunnelHopEntry are used to denote the hops this tunnel will take across the network. The following denotes the beginning of the network, or the Srinivasan et al. Expires September 2001 [Page 9] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 first hop. We have used the fictitious LSR identified by "123.123.125.1" as our example head-end router. In mplsTunnelHopTable: { mplsTunnelHopListIndex = 1, mplsTunnelPathOptionIndex = 1, mplsTunnelHopIndex = 1, mplsTunnelHopAddrType = 1, mplsTunnelHopIpv4Addr = 123.123.125.1, mplsTunnelHopIpv4PrefixLen = 9, mplsTunnelHopType = loose (2), mplsTunnelHopRowStatus = createAndGo (4) } The following denotes the end of the network, or the last hop in our example. We have used the fictitious LSR identified by "123.123.126.1" as our end router. In mplsTunnelHopTable: { mplsTunnelHopListIndex = 1, mplsTunnelPathOptionIndex = 1, mplsTunnelHopIndex = 2, mplsTunnelHopAddrType = 1, mplsTunnelHopIpv4Addr = 123.123.126.1, mplsTunnelHopIpv4PrefixLen = 9, mplsTunnelHopType = loose (2), mplsTunnelHopRowStatus = createAndGo (4) } 9. The Use of RowPointer RowPointer is a textual convention used to identify a conceptual row in an SNMP Table by pointing to one of its objects. In this MIB, in mplsTunnelTable, the objects mplsTunnelXCPointer and mplsTunnelResourcePointer are of type RowPointer. The object mplsTunnelXCPointer points to a specific entry in the mplsXCTable [LSRMIB]. This entry in the mplsXCTable is the associated LSP for the given MPLS tunnel entry. The object mplsTunnelResourcePointer points to a specific entry in a traffic parameter table. An example of such a traffic parameter table is mplsTunnelResourceTable. It indicates a specific instance of a traffic parameter entry that is associated with a given MPLS tunnel entry. 10. MPLS Traffic Engineering MIB Definitions Srinivasan et al. Expires September 2001 [Page 10] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 MPLS-TE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, experimental, Integer32, Unsigned32, Counter32, Counter64, TimeTicks, TimeStamp FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, TruthValue, RowStatus, RowPointer, StorageType, DisplayString FROM SNMPv2-TC InterfaceIndexOrZero FROM IF-MIB MplsBitRate, MplsBurstSize, MplsLSPID FROM MPLS-LSR-MIB InetAddressIPv4, InetAddressIPv6 FROM INET-ADDRESS-MIB; mplsTeMIB MODULE-IDENTITY LAST-UPDATED "200103021200Z" -- March 2, 2001 12:00:00 EST ORGANIZATION "Multiprotocol Label Switching (MPLS) Working Group" CONTACT-INFO " Cheenu Srinivasan Postal: Tachion Networks, Inc. Monmouth Park Corporate Center I Building C, 185 Monmouth Park Highway West Long Branch, NJ 07764 Tel: +1-732-542-7750 x1234 Email: cheenu@tachion.com Arun Viswanathan Postal: Force10 Networks, Inc. 1440 McCarthy Blvd Milpitas, CA 95035 Tel: +1-408-571-3516 Email: arun@force10networks.com Thomas D. Nadeau Postal: Cisco Systems, Inc. 250 Apollo Drive Srinivasan et al. Expires September 2001 [Page 11] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 Chelmsford, MA 01824 Tel: +1-978-244-3051 Email: tnadeau@cisco.com" DESCRIPTION "This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: Extensions to RSVP for LSP Tunnels, Awduche et al, Internet Draft , August 2000; Constraint-Based LSP Setup using LDP, B. Jamoussi, Internet Draft , July 2000; Requirements for Traffic Engineering Over MPLS, Awduche, D., J. Malcolm, J., Agogbua, J., O'Dell, M., J. McManus, , September 1999." -- Revision history. REVISION "200103021200Z" -- 2 March 2001 12:00:00 EST DESCRIPTION "Updates based on MPLS WG last call feedback." REVISION "200011211200Z" -- 21 November 2000 12:00:00 EST DESCRIPTION "Updates based on MPLS WG feedback." REVISION "200007141200Z" -- 14 July 2000 12:00:00 EST DESCRIPTION "Updates based on MPLS WG feedback." REVISION "200005261200Z" -- 26 May 2000 12:00:00 EST DESCRIPTION "Updates based on MPLS WG feedback." REVISION "200003031200Z" -- 3 March 2000 12:00:00 EST DESCRIPTION "Updates based on MPLS WG feedback." REVISION "199907161200Z" -- 16 July 1999 12:00:00 EST DESCRIPTION "Initial draft version." ::= { experimental 95 } -- Textual Conventions. MplsTunnelIndex ::= TEXTUAL-CONVENTION STATUS current Srinivasan et al. Expires September 2001 [Page 12] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 DESCRIPTION "Index into mplsTunnelTable." SYNTAX Integer32 (1..65535) MplsTunnelInstanceIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Instance index into mplsTunnelTable." SYNTAX Unsigned32 (0..65535) MplsTunnelAffinity ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Include-any, include-all, or exclude-all constraint for link selection." SYNTAX Unsigned32 MplsLsrId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A unique identifier for an MPLS LSR. This MAY represent an IpV4 address." SYNTAX Unsigned32 MplsPathIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A unique identifier used to identify a specific path used by a tunnel." SYNTAX Unsigned32 MplsPathIndexOrZero ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A unique identifier used to identify a specific path used by a tunnel. If this value is set to 0, it indicates that no path is in use." SYNTAX Unsigned32 -- Top level components of this MIB. -- tables, scalars mplsTeScalars OBJECT IDENTIFIER ::= { mplsTeMIB 1 } mplsTeObjects OBJECT IDENTIFIER ::= { mplsTeMIB 2 } -- traps mplsTeNotifications OBJECT IDENTIFIER ::= { mplsTeMIB 3 } mplsTeNotifyPrefix OBJECT IDENTIFIER ::= { mplsTeNotifications 0 } Srinivasan et al. Expires September 2001 [Page 13] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 -- conformance mplsTeConformance OBJECT IDENTIFIER ::= { mplsTeMIB 4 } -- MPLS Tunnel scalars. mplsTunnelConfigured OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of tunnels configured on this device. A tunnel is considered configured if the mplsTunnelRowStatus is active(1)." ::= { mplsTeScalars 1 } mplsTunnelActive OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of tunnels active on this device. A tunnel is considered active if the mplsTunnelOperStatus is up(1)." ::= { mplsTeScalars 2 } mplsTunnelTEDistProto OBJECT-TYPE SYNTAX BITS { other (0), ospf (1), isis (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The traffic engineering distribution protocol(s) used by this LSR. Note that an LSR may support more than one distribution protocol simultaneously." ::= { mplsTeScalars 3 } mplsTunnelMaxHops OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of hops that can be specified for a tunnel on this device." ::= { mplsTeScalars 4 } Srinivasan et al. Expires September 2001 [Page 14] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 -- End of MPLS Tunnel scalars. -- MPLS tunnel table. mplsTunnelIndexNext OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the next appropriate value to be used for mplsTunnelIndex when creating entries in mplsTunnelTable. If the number of unassigned entries is exhausted, a retrival operation will return a value of 0. This object may also return a value of 0 when the LSR is unable to accept conceptual row creation, for example, if the mplsTunnelTable is implemented as read-only. To obtain the value of mplsTunnelIndex for a new entry, the manager must first issue a management protocol retrieval operation to obtain the current value of this object. The agent should modify the value to reflect the next unassigned index after each retrieval operation. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse." ::= { mplsTeObjects 1 } mplsTunnelTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsTunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The mplsTunnelTable allows new MPLS tunnels to be created between an LSR and a remote endpoint, and existing tunnels to be reconfigured or removed. Note that only point-to-point tunnel segments are supported, although multi-point-to-point and point- to-multi-point connections are supported by an LSR acting as a cross-connect. Each MPLS tunnel can thus have one out-segment originating at this LSR and/or one in-segment terminating at this LSR." ::= { mplsTeObjects 2 } mplsTunnelEntry OBJECT-TYPE SYNTAX MplsTunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION Srinivasan et al. Expires September 2001 [Page 15] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 "An entry in this table represents an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling protocol. Whenever a new entry is created with mplsTunnelIsIf set to true(1), then a corresponding entry is created in ifTable as well (see RFC 2233). The ifType of this entry is mplsTunnel(150)." REFERENCE "1. RFC 2233 - The Interfaces Group MIB using SMIv2, McCloghrie, K., and F. Kastenholtz, Nov. 1997 2. RFC 1700 - Assigned Numbers, Reynolds, J. and J. Postel, Oct. 1994" INDEX { mplsTunnelIndex, mplsTunnelInstance, mplsTunnelIngressLSRId, mplsTunnelEgressLSRId } ::= { mplsTunnelTable 1 } MplsTunnelEntry ::= SEQUENCE { mplsTunnelIndex MplsTunnelIndex, mplsTunnelInstance MplsTunnelInstanceIndex, mplsTunnelIngressLSRId MplsLsrId, mplsTunnelEgressLSRId MplsLsrId, mplsTunnelName DisplayString, mplsTunnelDescr DisplayString, mplsTunnelIsIf TruthValue, mplsTunnelIfIndex InterfaceIndexOrZero, mplsTunnelXCPointer RowPointer, mplsTunnelSignallingProto INTEGER, mplsTunnelSetupPrio INTEGER, mplsTunnelHoldingPrio INTEGER, mplsTunnelSessionAttributes BITS, mplsTunnelOwner INTEGER, mplsTunnelLocalProtectInUse TruthValue, mplsTunnelResourcePointer RowPointer, mplsTunnelInstancePriority Unsigned32, mplsTunnelHopTableIndex MplsPathIndexOrZero, mplsTunnelARHopTableIndex MplsPathIndexOrZero, mplsTunnelCHopTableIndex MplsPathIndexOrZero, mplsTunnelPrimaryInstance MplsTunnelInstanceIndex, mplsTunnelPrimaryTimeUp TimeTicks, mplsTunnelPathChanges Counter32, mplsTunnelLastPathChange TimeTicks, mplsTunnelCreationTime TimeStamp, mplsTunnelStateTransitions Counter32, mplsTunnelIncludeAnyAffinity MplsTunnelAffinity, mplsTunnelIncludeAllAffinity MplsTunnelAffinity, mplsTunnelExcludeAllAffinity MplsTunnelAffinity, mplsTunnelPathInUse MplsPathIndexOrZero, mplsTunnelRole INTEGER, Srinivasan et al. Expires September 2001 [Page 16] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 mplsTunnelTotalUpTime TimeTicks, mplsTunnelInstanceUpTime TimeTicks, mplsTunnelAdminStatus INTEGER, mplsTunnelOperStatus INTEGER, mplsTunnelRowStatus RowStatus, mplsTunnelStorageType StorageType } mplsTunnelIndex OBJECT-TYPE SYNTAX MplsTunnelIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Uniquely identifies this row." ::= { mplsTunnelEntry 1 } mplsTunnelInstance OBJECT-TYPE SYNTAX MplsTunnelInstanceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Uniquely identifies an instance of a tunnel. It is useful to identify multiple instances of tunnels for the purposes of backup and parallel tunnels." ::= { mplsTunnelEntry 2 } mplsTunnelIngressLSRId OBJECT-TYPE SYNTAX MplsLsrId MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The purpose of this object is to uniquely identity a tunnel within a network. When the MPLS signalling protoocol is rsvp(2) this value should mimic the Extended Tunnel Id field in the Session object. When the MPLS signalling protoocol is crldp(3) this value should mimic the Ingress LSR Router ID field in the LSPID TLV object." REFERENCE "1. RSVP-TE: Extensions to RSVP for LSP Tunnels, Awduche et al, Internet Draft , August 2000., 2. Constraint-Based LSP Setup using LDP, Jamoussi, Internet Draft , July 2000." ::= { mplsTunnelEntry 3 } mplsTunnelEgressLSRId OBJECT-TYPE SYNTAX MplsLsrId MAX-ACCESS accessible-for-notify Srinivasan et al. Expires September 2001 [Page 17] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 STATUS current DESCRIPTION "Specifies the egress LSR Id." ::= { mplsTunnelEntry 4 } mplsTunnelName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSRÆs console port. If mplsTunnelIsIf is set to true then the ifName of the interface corresponding to this tunnel should have a value equal to mplsTunnelName. Also see the description of ifName in RFC 2233." REFERENCE "RFC 2233 - The Interfaces Group MIB using SMIv2, McCloghrie, K., and F. Kastenholtz, Nov. 1997" ::= { mplsTunnelEntry 5 } mplsTunnelDescr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "A textual string containing information about the tunnel. If there is no description this object contains a zero length string." ::= { mplsTunnelEntry 6 } mplsTunnelIsIf OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Denotes whether or not this tunnel corresponds to an interface represented in the interfaces group table. Note that if this variable is set to true then the ifName of the interface corresponding to this tunnel should have a value equal to mplsTunnelName. Also see the description of ifName in RFC 2233." REFERENCE "RFC 2233 - The Interfaces Group MIB using SMIv2, McCloghrie, K., and F. Kastenholtz, Nov. 1997" DEFVAL { false } ::= { mplsTunnelEntry 7 } Srinivasan et al. Expires September 2001 [Page 18] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 mplsTunnelIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "If mplsTunnelIsIf is set to true, then this value contains the LSR-assigned ifIndex which corresponds to an entry in the interfaces table. Otherwise this variable should contain the value of zero indicating that a valid ifIndex was not assigned to this tunnel interface." REFERENCE "RFC 2233 - The Interfaces Group MIB using SMIv2, McCloghrie, K., and F. Kastenholtz, Nov. 1997" ::= { mplsTunnelEntry 8 } mplsTunnelXCPointer OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-create STATUS current DESCRIPTION "This variable points to a row in the mplsXCTable. This table identifies the segments that compose this tunnel, their characteristics, and relationships to each other. A value of zeroDotZero indicates that no LSP has been associated with this tunnel yet." REFERENCE "Srinivasan, C., Viswanathan, A., and T. Nadeau, MPLS Label Switch Router Management Information Base Using SMIv2, Internet Draft , July 2000." ::= { mplsTunnelEntry 9 } mplsTunnelSignallingProto OBJECT-TYPE SYNTAX INTEGER { none(1), rsvp(2), crldp(3), other(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The signaling protocol, if any, which was used to setup this tunnel." DEFVAL { none } ::= { mplsTunnelEntry 10 } mplsTunnelSetupPrio OBJECT-TYPE Srinivasan et al. Expires September 2001 [Page 19] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the setup priority of this tunnel." REFERENCE "1. RSVP-TE: Extensions to RSVP for LSP Tunnels, Awduche et al, Internet Draft , August 2000., 2. Constraint-Based LSP Setup using LDP, Jamoussi, Internet Draft , July 2000." ::= { mplsTunnelEntry 11 } mplsTunnelHoldingPrio OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the holding priority for this tunnel." REFERENCE "1. RSVP-TE: Extensions to RSVP for LSP Tunnels, Awduche et al, Internet Draft , August 2000., 2. Constraint-Based LSP Setup using LDP, Jamoussi, Internet Draft , July 2000." ::= { mplsTunnelEntry 12 } mplsTunnelSessionAttributes OBJECT-TYPE SYNTAX BITS { fastReroute (0), mergingPermitted (1), isPersistent (2), isPinned (3), recordRoute(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "This bitmask indicates optional session values for this tunnel. The following describes these bitfields: fastRerouteThis flag indicates that the any tunnel hop may choose to reroute this tunnel without tearing it down. This flag permits transit routers to use a local repair mechanism which may result in violation of the explicit routing of this tunnel. When a fault is detected on an adjacent downstream Srinivasan et al. Expires September 2001 [Page 20] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 link or node, a transit router can reroute traffic for fast service restoration. mergingPermitted This flag permits transit routers to merge this session with other RSVP sessions for the purpose of reducing resource overhead on downstream transit routers, thereby providing better network scalability. isPersistent Indicates whether this tunnel should be restored automatically after a failure occurs. isPinned This flag indicates whether the loose- routed hops of this tunnel are to be pinned. recordRouteThis flag indicates whether or not the signaling protocol should remember the tunnel path after it has been signaled." REFERENCE "1. RSVP-TE: Extensions to RSVP for LSP Tunnels, Awduche et al, Internet Draft , August 2000." DEFVAL { 0 } ::= { mplsTunnelEntry 13 } mplsTunnelOwner OBJECT-TYPE SYNTAX INTEGER { admin(1), -- represents all management entities rsvp(2), crldp(3), policyAgent(4), other(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates which protocol created and is responsible for managing this tunnel. Values rsvp(2) and crldp(3) should not be used at the head-end of a MPLS tunnel." ::= { mplsTunnelEntry 14 } mplsTunnelLocalProtectInUse OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates that the local repair mechanism is in use to maintain this tunnel (usually in the face of an Srinivasan et al. Expires September 2001 [Page 21] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 outage of the link it was previously routed over)." ::= { mplsTunnelEntry 15 } mplsTunnelResourcePointer OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-create STATUS current DESCRIPTION "This variable represents a pointer to the traffic parameter specification for this tunnel. This value may point at an entry in the mplsTunnelResourceEntry to indicate which mplsTunnelResourceEntry is to be assigned to this segment. This value may optionally point at an externally defined traffic parameter specification table. A value of zeroDotZero indicates best- effort treatment. By having the same value of this object, two or more segments can indicate resource sharing." ::= { mplsTunnelEntry 16 } mplsTunnelInstancePriority OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This value indicates which priority, in descending order, with 0 indicating the lowest priority, within a group of tunnel instances. A group of tunnel instances is defined as a set of tunnels with the same mplsTunnelIndex in this table, but with a different mplsTunnelInstance. Tunnel group priorities are used to denote the priority at which a particular tunnel instance will supercede another. Instances of tunnels containing the same mplsTunnelInstancePriority will be used for load sharing." DEFVAL { 0 } ::= { mplsTunnelEntry 17 } mplsTunnelHopTableIndex OBJECT-TYPE SYNTAX MplsPathIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "Index into the mplsTunnelHopTable entry that specifies the explicit route hops for this tunnel." ::= { mplsTunnelEntry 18 } mplsTunnelARHopTableIndex OBJECT-TYPE Srinivasan et al. Expires September 2001 [Page 22] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 SYNTAX MplsPathIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "Index into the mplsTunnelARHopTable entry that specifies the actual hops traversed by the tunnel." ::= { mplsTunnelEntry 19 } mplsTunnelCHopTableIndex OBJECT-TYPE SYNTAX MplsPathIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "Index into the mplsTunnelCHopTable entry that specifies the computed hops traversed by the tunnel." ::= { mplsTunnelEntry 20 } mplsTunnelPrimaryInstance OBJECT-TYPE SYNTAX MplsTunnelInstanceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the instance index of the primary instance of this tunnel." ::= { mplsTunnelEntry 21 } mplsTunnelPrimaryTimeUp OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the total time the primary instance of this tunnel has been active. The primary instance of this tunnel is defined in mplsTunnelPrimaryInstance." ::= { mplsTunnelEntry 22 } mplsTunnelPathChanges OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the number of times the paths has changed for this tunnel." ::= { mplsTunnelEntry 23 } mplsTunnelLastPathChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only Srinivasan et al. Expires September 2001 [Page 23] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 STATUS current DESCRIPTION "Specifies the time since the last path change for this tunnel." ::= { mplsTunnelEntry 24 } mplsTunnelCreationTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the value of SysUpTime when the first instance of this tunnel came into existence." ::= { mplsTunnelEntry 25 } mplsTunnelStateTransitions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the number of times the state of this tunnel instance has changed." ::= { mplsTunnelEntry 26 } mplsTunnelIncludeAnyAffinity OBJECT-TYPE SYNTAX MplsTunnelAffinity MAX-ACCESS read-create STATUS current DESCRIPTION "A link satisfies the include-any constraint if and only if the constraint is zero, or the link and the constraint have a resource class in common." REFERENCE "RSVP-TE: Extensions to RSVP for LSP Tunnels, draft-ietf-mpls-rsvp-lsp-tunnel-07.txt" ::= { mplsTunnelEntry 27 } mplsTunnelIncludeAllAffinity OBJECT-TYPE SYNTAX MplsTunnelAffinity MAX-ACCESS read-create STATUS current DESCRIPTION "A link satisfies the include-all constraint if and only if the link contains all of the adminstrative groups specified in the constraint." REFERENCE "RSVP-TE: Extensions to RSVP for LSP Tunnels, draft-ietf-mpls-rsvp-lsp-tunnel-07.txt" ::= { mplsTunnelEntry 28 } mplsTunnelExcludeAllAffinity OBJECT-TYPE Srinivasan et al. Expires September 2001 [Page 24] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 SYNTAX MplsTunnelAffinity MAX-ACCESS read-create STATUS current DESCRIPTION "A link satisfies the exclude-all constraint if and only if the link contains none of the adminstrative groups specifie in the constraint." REFERENCE "RSVP-TE: Extensions to RSVP for LSP Tunnels, draft-ietf-mpls-rsvp-lsp-tunnel-07.txt" ::= { mplsTunnelEntry 29 } mplsTunnelPathInUse OBJECT-TYPE SYNTAX MplsPathIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "This value denotes the configured path that was chosen for this tunnel. This value reflects the secondary index into the TunnelHopTable. This path may not exactly match the one in the ARHopTable due to the fact that some CSPF modification may have taken place. See the ARHopTable for the actual path being taken by the tunnel. A value of zero denotes that no path is currently in use or available." ::= { mplsTunnelEntry 30 } mplsTunnelRole OBJECT-TYPE SYNTAX INTEGER { head(1), transit(2), tail(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "This value signifies the role that this tunnel entry/instance represents. This value MUST be set to head(1) at the originating point of the tunnel. This value MUST be set to transit(2) at transit points along the tunnel, if transit points are supported. This value MUST be set to tail(3) at the terminating point of the tunnel if tunnel tails are supported." ::= { mplsTunnelEntry 31 } mplsTunnelTotalUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-create STATUS current DESCRIPTION "This value represents the aggregate up time for all instances of this tunnel, if available. If this value is unavailable, it MUST return a value of 0." Srinivasan et al. Expires September 2001 [Page 25] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 ::= { mplsTunnelEntry 32 } mplsTunnelInstanceUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-create STATUS current DESCRIPTION "This value identifies the total time that this tunnel instance's operStatus has been Up(1)." ::= { mplsTunnelEntry 33 } mplsTunnelAdminStatus OBJECT-TYPE SYNTAX INTEGER { -- ready to pass packets up(1), down(2), -- in some test mode testing(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the desired operational status of this tunnel." ::= { mplsTunnelEntry 34 } mplsTunnelOperStatus OBJECT-TYPE SYNTAX INTEGER { -- ready to pass packets up(1), down(2), -- in some test mode testing(3), -- status cannot be determined unknown(4), dormant(5), -- some component is missing notPresent(6), -- down due to the state of -- lower layer interfaces lowerLayerDown(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the actual operational status of this tunnel, which is typically but not limited to, a function of the state of individual segments of this tunnel." ::= { mplsTunnelEntry 35 } Srinivasan et al. Expires September 2001 [Page 26] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 mplsTunnelRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table." ::= { mplsTunnelEntry 36 } mplsTunnelStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this object." ::= { mplsTunnelEntry 37 } -- End of mplsTunnelTable mplsTunnelHopListIndexNext OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for mplsTunnelHopListIndex when creating entries in the mplsTunnelHopTable. If the number of unassigned entries is exhausted, a retrival operation will return a value of 0. This object may also return a value of 0 when the LSR is unable to accept conceptual row creation, for example, if the mplsTunnelHopTable is implemented as read-only. To obtain the value of mplsTunnelHopListIndex for a new entry in the mplsTunnelHopTable, the manager issues a management protocol retrieval operation to obtain the current value of mplsTunnelHopIndex. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse." ::= { mplsTeObjects 3 } mplsTunnelHopTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsTunnelHopEntry MAX-ACCESS not-accessible STATUS current Srinivasan et al. Expires September 2001 [Page 27] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 DESCRIPTION "The mplsTunnelHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsTunnelTable, when it is established via signaling, for the outgoing direction of the tunnel. Each row in this table is indexed by mplsTunnelHopListIndex. Each row also has a secondary index mplsTunnelHopIndex corresponding to the next hop that this row corresponds to. The first row in the table is the first hop after the origination point of the tunnel. In case we want to specify a particular interface on the originating LSR of an outgoing tunnel by which we want packets to exit the LSR, we specify this as the first hop for this tunnel in mplsTunnelHopTable." ::= { mplsTeObjects 4 } mplsTunnelHopEntry OBJECT-TYPE SYNTAX MplsTunnelHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents a tunnel hop. An entry is created by a network administrator for signaled ERLSP set up by an MPLS signaling protocol." INDEX { mplsTunnelHopListIndex, mplsTunnelHopPathOptionIndex, mplsTunnelHopIndex } ::= { mplsTunnelHopTable 1 } MplsTunnelHopEntry ::= SEQUENCE { mplsTunnelHopListIndex MplsPathIndex, mplsTunnelHopPathOptionIndex MplsPathIndex, mplsTunnelHopIndex MplsPathIndex, mplsTunnelHopAddrType INTEGER, mplsTunnelHopIpv4Addr InetAddressIPv4, mplsTunnelHopIpv4PrefixLen Unsigned32, mplsTunnelHopIpv6Addr InetAddressIPv6, mplsTunnelHopIpv6PrefixLen Unsigned32, mplsTunnelHopAsNumber Unsigned32, mplsTunnelHopLspId MplsLSPID, mplsTunnelHopType INTEGER, mplsTunnelHopIncludeExclude INTEGER, mplsTunnelHopPathOptionName DisplayString, mplsTunnelHopEntryPathComp INTEGER, mplsTunnelHopRowStatus RowStatus, mplsTunnelHopStorageType StorageType } Srinivasan et al. Expires September 2001 [Page 28] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 mplsTunnelHopListIndex OBJECT-TYPE SYNTAX MplsPathIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Primary index into this table identifying a particular explicit route object." ::= { mplsTunnelHopEntry 1 } mplsTunnelHopPathOptionIndex OBJECT-TYPE SYNTAX MplsPathIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Secondary index into this table identifying a particular group of hops representing a particular configured path. This is otherwise known as a path option." ::= { mplsTunnelHopEntry 2 } mplsTunnelHopIndex OBJECT-TYPE SYNTAX MplsPathIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Secondary index into this table identifying a particular hop." ::= { mplsTunnelHopEntry 3 } mplsTunnelHopAddrType OBJECT-TYPE SYNTAX INTEGER { ipV4(1), ipV6(2), asNumber(3), lspid(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Denotes the address type of this tunnel hop." DEFVAL { ipV4 } ::= { mplsTunnelHopEntry 4 } mplsTunnelHopIpv4Addr OBJECT-TYPE SYNTAX InetAddressIPv4 MAX-ACCESS read-create STATUS current DESCRIPTION "If mplsTunnelHopAddrType is set to ipV4(1), then this value will contain the IPv4 address of this Srinivasan et al. Expires September 2001 [Page 29] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 hop. If mplsTunnelHopAddrType is set to lspid(4), then this value will contain the Ingress LSR Router ID of the Tunnel. This object is otherwise insignificant and should contain a value of 0." ::= { mplsTunnelHopEntry 5 } mplsTunnelHopIpv4PrefixLen OBJECT-TYPE SYNTAX Unsigned32 (0..32) MAX-ACCESS read-create STATUS current DESCRIPTION "If mplsTunnelHopAddrType is ipV4(1), then the prefix length for this hop's IPv4 address is contained herein. This object is otherwise insignificant and should contain a value of 0." ::= { mplsTunnelHopEntry 6 } mplsTunnelHopIpv6Addr OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-create STATUS current DESCRIPTION "If the mplsTunnelHopAddrType is set to ipV6(2), then this variable contains the IPv6 address of this hop. This object is otherwise insignificant and should contain a value of 0." ::= { mplsTunnelHopEntry 7 } mplsTunnelHopIpv6PrefixLen OBJECT-TYPE SYNTAX Unsigned32 (0..128) MAX-ACCESS read-create STATUS current DESCRIPTION "If mplsTunnelHopAddrType is set to ipV6(2), this value will contain the prefix length for this hop's IPv6 address. This object is otherwise insignificant and should contain a value of 0." ::= { mplsTunnelHopEntry 8 } mplsTunnelHopAsNumber OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "If mplsTunnelHopAddrType is set to asNumber(3), then this value will contain the AS number of this hop. This object is otherwise insignificant and should contain a value of 0 to indicate this fact." ::= { mplsTunnelHopEntry 9 } Srinivasan et al. Expires September 2001 [Page 30] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 mplsTunnelHopLspId OBJECT-TYPE SYNTAX MplsLSPID MAX-ACCESS read-create STATUS current DESCRIPTION "If mplsTunnelHopAddrType is set to lspid(4), then this value will contain the LSPID of a tunnel of this hop. The present tunnel being configured is ætunneledÆ through this hop (using label stacking). This object is otherwise insignificant and should contain a value of 0 to indicate this fact." ::= { mplsTunnelHopEntry 10 } mplsTunnelHopType OBJECT-TYPE SYNTAX INTEGER { strict(1), loose(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Denotes whether this tunnel hop is routed in a strict or loose fashion." ::= { mplsTunnelHopEntry 11 } mplsTunnelHopIncludeExclude OBJECT-TYPE SYNTAX INTEGER { include(1), exclude(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "If this value is set to include(1), then this indicates that this hop must be included in the tunnel's path. If this value is set to exclude(2), then this hop must be avoided when calculating the path for this tunnel. The default value of this object is include(1), so that by default all indicated hops are included in the CSPF path computation." DEFVAL { include } ::= { mplsTunnelHopEntry 12 } mplsTunnelHopPathOptionName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The description of this series of hops as they Srinivasan et al. Expires September 2001 [Page 31] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 relate to the specified path option." ::= { mplsTunnelHopEntry 13 } mplsTunnelHopEntryPathComp OBJECT-TYPE SYNTAX INTEGER { dynamic(1), -- CSPF computed explicit(2) -- strict hop } MAX-ACCESS read-create STATUS current DESCRIPTION "If this value is set to dynamic, then the user should only specify the source and destination of the path and expect that the CSPF will calculate the remainder of the path. If this value is set to explicit, the user should specify the entire path for the tunnel to take. This path may contain strict or loose hops. Each hop along a specific path should have this object set to the same value" ::= { mplsTunnelHopEntry 14 } mplsTunnelHopRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table." ::= { mplsTunnelHopEntry 15 } mplsTunnelHopStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this object." ::= { mplsTunnelHopEntry 16 } -- End of mplsTunnelHopTable -- Begin of mplsTunnelResourceTable mplsTunnelResourceIndexNext OBJECT-TYPE SYNTAX Unsigned32 (0.. 2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the next appropriate value to Srinivasan et al. Expires September 2001 [Page 32] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 be used for mplsTunnelResourceIndex when creating entries in the mplsTunnelResourceTable. If the number of unassigned entries is exhausted, a retrival operation will return a value of 0. This object may also return a value of 0 when the LSR is unable to accept conceptual row creation, for example, if the mplsTunnelTable is implemented as read-only. To obtain the mplsTunnelResourceIndex value for a new entry, the manager must first issue a management protocol retrieval operation to obtain the current value of this object. The agent should modify the value to reflect the next unassigned index after each retrieval operation. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse." ::= { mplsTeObjects 5 } mplsTunnelResourceTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsTunnelResourceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The mplsTunnelResourceTable allows a manager to specify which resources are desired for an MPLS tunnel. This table also allows several tunnels to point to a single entry in this table, implying that these tunnels should share resources." ::= { mplsTeObjects 6 } mplsTunnelResourceEntry OBJECT-TYPE SYNTAX MplsTunnelResourceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents a set of resources for an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by any MPLS signaling protocol." INDEX { mplsTunnelResourceIndex } ::= { mplsTunnelResourceTable 1 } MplsTunnelResourceEntry ::= SEQUENCE { mplsTunnelResourceIndex Unsigned32, mplsTunnelResourceMaxRate MplsBitRate, mplsTunnelResourceMeanRate MplsBitRate, mplsTunnelResourceMaxBurstSize MplsBurstSize, mplsTunnelResourceMeanBurstSize MplsBurstSize, mplsTunnelResourceExcessBurstSize MplsBurstSize, mplsTunnelResourceFrequency INTEGER, Srinivasan et al. Expires September 2001 [Page 33] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 mplsTunnelResourceWeight Unsigned32, mplsTunnelResourceRowStatus RowStatus, mplsTunnelResourceStorageType StorageType } mplsTunnelResourceIndex OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Uniquely identifies this row." ::= { mplsTunnelResourceEntry 1 } mplsTunnelResourceMaxRate OBJECT-TYPE SYNTAX MplsBitRate UNITS "bits per second" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum rate in bits/second. Note that setting mplsTunnelResourceMaxRate, mplsTunnelResourceMeanRate, and mplsTunnelResourceMaxBurstSize to 0 indicates best- effort treatment. This object is copied to an instance of mplsTrafficParamMaxRate in mplsTrafficParamTable the OID of which is copied into the corresponding mplsInSegmentTrafficParamPtr." REFERENCE "Srinivasan, C., Viswanathan, A., and T. Nadeau, MPLS Label Switch Router Management Information Base Using SMIv2, Internet Draft , July 2000." ::= { mplsTunnelResourceEntry 2 } mplsTunnelResourceMeanRate OBJECT-TYPE SYNTAX MplsBitRate UNITS "bits per second" MAX-ACCESS read-create STATUS current DESCRIPTION "This object is copied into an instance of mplsTrafficParamMeanRate in the mplsTrafficParamTable. The OID of this table entry is then copied into the corresponding mplsInSegmentTrafficParamPtr. When resource allocation is performed as requested by this TSpec object, it is copied into an entry in mplsTrafficParamTable [LSRMIB]: Srinivasan et al. Expires September 2001 [Page 34] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 mplsTunnelInMeanRate to mplsTrafficParamMeanRate. The OID of this entry is copied to mplsInSegmentTrafficParamPtr of the corresponding in-segment entry." REFERENCE "Srinivasan, C., Viswanathan, A., and T. Nadeau, MPLS Label Switch Router Management Information Base Using SMIv2, Internet Draft , July 2000." ::= { mplsTunnelResourceEntry 3 } mplsTunnelResourceMaxBurstSize OBJECT-TYPE SYNTAX MplsBurstSize UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum burst size in bytes. This object is copied to mplsInSegmentMaxBurstSize of the corresponding in-segment. When resource allocation is performed as requested by this TSpec object, it is copied into an entry in mplsTrafficParamTable [LSRMIB]: mplsTunnelInMaxBurstSize to mplsTrafficParamMaxBurstSize. The OID of this entry is copied to mplsInSegmentTrafficParamPtr of the corresponding in-segment entry." REFERENCE "Srinivasan, C., Viswanathan, A., and T. Nadeau, MPLS Label Switch Router Management Information Base Using SMIv2, Internet Draft , July 2000." ::= { mplsTunnelResourceEntry 4 } mplsTunnelResourceMeanBurstSize OBJECT-TYPE SYNTAX MplsBurstSize UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "The mean burst size in bytes. The implementations which do not implement this variable must return 0 for this value and must not allow a user to set this value." ::= { mplsTunnelResourceEntry 5 } mplsTunnelResourceExcessBurstSize OBJECT-TYPE SYNTAX MplsBurstSize Srinivasan et al. Expires September 2001 [Page 35] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "The Excess burst size in bytes. The implementations which do not implement this variable must return 0 for this value and must not allow a user to set this value." REFERENCE "CR-LDP Specification, Section 4.3." ::= { mplsTunnelResourceEntry 6 } mplsTunnelResourceFrequency OBJECT-TYPE SYNTAX INTEGER { unspecified(1), frequent(2), veryFrequent(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The granularity of the availability of committed rate. The implementations which do not implement this variable must return unspecified(1) for this value and must not allow a user to set this value." REFERENCE "CR-LDP Specification, Section 4.3." ::= { mplsTunnelResourceEntry 7 } mplsTunnelResourceWeight OBJECT-TYPE SYNTAX Unsigned32(0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The relative weight for using excess bandwidth above its committed rate. The value of 0 means that weight is not applicable for the CR-LSP." REFERENCE "CR-LDP Specification, Section 4.3." ::= { mplsTunnelResourceEntry 8 } mplsTunnelResourceRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table." ::= { mplsTunnelResourceEntry 9 } Srinivasan et al. Expires September 2001 [Page 36] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 mplsTunnelResourceStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this object." ::= { mplsTunnelResourceEntry 10 } -- End mplsTunnelResourceTable -- Tunnel Actual Route Hop table. mplsTunnelARHopTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsTunnelARHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The mplsTunnelARHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsTunnelTable, as reported by the MPLS signaling protocol, for the outgoing direction of the tunnel. Each row in this table is indexed by mplsTunnelARHopListIndex. Each row also has a secondary index mplsTunnelARHopIndex, corresponding to the next hop that this row corresponds to. The first row in the table is the first hop after the origination point of the tunnel. In case we want to specify a particular interface on the originating LSR of an outgoing tunnel by which we want packets to exit the LSR, we specify this as the first hop for this tunnel in mplsTunnelARHopTable. Please note that since the information necessary to build entries within this table are not provided by some MPLS signaling protocols, implementation of this table is optional. Furthermore, since the information in this table is actually provided by the MPLS signaling protocol after the path has been set-up, the entries in this table are provided only for observation, and hence, all variables in this table are accessible exclusively as read-only." ::= { mplsTeObjects 7 } mplsTunnelARHopEntry OBJECT-TYPE SYNTAX MplsTunnelARHopEntry MAX-ACCESS not-accessible STATUS current Srinivasan et al. Expires September 2001 [Page 37] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 DESCRIPTION "An entry in this table represents a tunnel hop. An entry is created by a network administrator for signaled ERLSP set up by an MPLS signaling protocol." INDEX { mplsTunnelARHopListIndex, mplsTunnelARHopIndex } ::= { mplsTunnelARHopTable 1 } MplsTunnelARHopEntry ::= SEQUENCE { mplsTunnelARHopListIndex MplsPathIndex, mplsTunnelARHopIndex MplsPathIndex, mplsTunnelARHopAddrType INTEGER, mplsTunnelARHopIpv4Addr InetAddressIPv4, mplsTunnelARHopIpv4PrefixLen Unsigned32, mplsTunnelARHopIpv6Addr InetAddressIPv6, mplsTunnelARHopIpv6PrefixLen Unsigned32, mplsTunnelARHopAsNumber Unsigned32, mplsTunnelARHopLspId MplsLSPID } mplsTunnelARHopListIndex OBJECT-TYPE SYNTAX MplsPathIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Primary index into this table identifying a particular recorded hop list." ::= { mplsTunnelARHopEntry 1 } mplsTunnelARHopIndex OBJECT-TYPE SYNTAX MplsPathIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Secondary index into this table identifying the particular hop." ::= { mplsTunnelARHopEntry 2 } mplsTunnelARHopAddrType OBJECT-TYPE SYNTAX INTEGER { ipV4(1), ipV6(2), asNumber(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Denotes the address type of this tunnel hop." DEFVAL { ipV4 } ::= { mplsTunnelARHopEntry 3 } Srinivasan et al. Expires September 2001 [Page 38] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 mplsTunnelARHopIpv4Addr OBJECT-TYPE SYNTAX InetAddressIPv4 MAX-ACCESS read-only STATUS current DESCRIPTION "If mplsTunnelARHopAddrType is set to ipV4(1), then this value will contain the IPv4 address of this hop. This object is otherwise insignificant and should contain a value of 0." ::= { mplsTunnelARHopEntry 4 } mplsTunnelARHopIpv4PrefixLen OBJECT-TYPE SYNTAX Unsigned32 (0..32) MAX-ACCESS read-only STATUS current DESCRIPTION "If mplsTunnelARHopAddrType is ipV4(1), then the prefix length for this hop's IPv4 address is contained herein. This object is otherwise insignificant and should contain a value of 0." ::= { mplsTunnelARHopEntry 5 } mplsTunnelARHopIpv6Addr OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-only STATUS current DESCRIPTION "If the mplsTunnelARHopAddrType is set to ipV6(2), then this variable contains the IPv6 address of this hop. This object is otherwise insignificant and should contain a value of 0." ::= { mplsTunnelARHopEntry 6 } mplsTunnelARHopIpv6PrefixLen OBJECT-TYPE SYNTAX Unsigned32 (0..128) MAX-ACCESS read-only STATUS current DESCRIPTION "If mplsTunnelARHopAddrType is set to ipV6(2), this value will contain the prefix length for this hop's IPv6 address. This object is otherwise insignificant and should contain a value of 0." ::= { mplsTunnelARHopEntry 7 } mplsTunnelARHopAsNumber OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION Srinivasan et al. Expires September 2001 [Page 39] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 "If mplsTunnelARHopAddrType is set to asNumber(3), then this value will contain the AS number of this hop. This object is otherwise insignificant and should contain a value of 0 to indicate this fact." ::= { mplsTunnelARHopEntry 8 } mplsTunnelARHopLspId OBJECT-TYPE SYNTAX MplsLSPID MAX-ACCESS read-only STATUS current DESCRIPTION "If mplsTunnelARHopAddrType is set to lspid(4), then this value will contain the LSP ID of this hop. This object is otherwise insignificant and should contain a value of 0 to indicate this fact." ::= { mplsTunnelARHopEntry 9 } -- End of mplsTunnelARHopTable -- Tunnel Computed Hop table. mplsTunnelCHopTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsTunnelCHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The mplsTunnelCHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsTunnelTable, as computed by a constraint- based routing protocol, based on the mplsTunnelHopTable for the outgoing direction of the tunnel. Each row in this table is indexed by mplsTunnelCHopListIndex. Each row also has a secondary index mplsTunnelCHopIndex, corresponding to the next hop that this row corresponds to. The first row in the table is the first hop after the origination point of the tunnel. In case we want to specify a particular interface on the originating LSR of an outgoing tunnel by which we want packets to exit the LSR, we specify this as the first hop for this tunnel in mplsTunnelCHopTable. Please note that since the information necessary to build entries within this table may not be supported by some LSRs, implementation of this table is optional. Furthermore, since the Srinivasan et al. Expires September 2001 [Page 40] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 information in this table is actually provided by routing protocol after the path has been computed, the entries in this table are provided only for observation, and hence, all variables in this table are accessible exclusively as read-only." ::= { mplsTeObjects 8 } mplsTunnelCHopEntry OBJECT-TYPE SYNTAX MplsTunnelCHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents a tunnel hop. An entry in this table is created by a constraint- based routing protocol based on the hops specified in the corresponding mplsTunnelHopTable." INDEX { mplsTunnelCHopListIndex, mplsTunnelCHopIndex } ::= { mplsTunnelCHopTable 1 } MplsTunnelCHopEntry ::= SEQUENCE { mplsTunnelCHopListIndex MplsPathIndex, mplsTunnelCHopIndex MplsPathIndex, mplsTunnelCHopAddrType INTEGER, mplsTunnelCHopIpv4Addr InetAddressIPv4, mplsTunnelCHopIpv4PrefixLen Unsigned32, mplsTunnelCHopIpv6Addr InetAddressIPv6, mplsTunnelCHopIpv6PrefixLen Unsigned32, mplsTunnelCHopAsNumber Unsigned32, mplsTunnelCHopType INTEGER } mplsTunnelCHopListIndex OBJECT-TYPE SYNTAX MplsPathIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Primary index into this table identifying a particular computed hop list." ::= { mplsTunnelCHopEntry 1 } mplsTunnelCHopIndex OBJECT-TYPE SYNTAX MplsPathIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Secondary index into this table identifying the particular hop." ::= { mplsTunnelCHopEntry 2 } mplsTunnelCHopAddrType OBJECT-TYPE Srinivasan et al. Expires September 2001 [Page 41] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 SYNTAX INTEGER { ipV4(1), ipV6(2), asNumber(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Denotes the address type of this tunnel hop." DEFVAL { ipV4 } ::= { mplsTunnelCHopEntry 3 } mplsTunnelCHopIpv4Addr OBJECT-TYPE SYNTAX InetAddressIPv4 MAX-ACCESS read-only STATUS current DESCRIPTION "If mplsTunnelCHopAddrType is set to ipV4(1), then this value will contain the IPv4 address of this hop. This object is otherwise insignificant and should contain a value of 0." ::= { mplsTunnelCHopEntry 4 } mplsTunnelCHopIpv4PrefixLen OBJECT-TYPE SYNTAX Unsigned32 (0..32) MAX-ACCESS read-only STATUS current DESCRIPTION "If mplsTunnelCHopAddrType is ipV4(1), then the prefix length for this hop's IPv4 address is contained herein. This object is otherwise insignificant and should contain a value of 0." ::= { mplsTunnelCHopEntry 5 } mplsTunnelCHopIpv6Addr OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-only STATUS current DESCRIPTION "If the mplsTunnelCHopAddrType is set to ipV6(2), then this variable contains the IPv6 address of this hop. This object is otherwise insignificant and should contain a value of 0." ::= { mplsTunnelCHopEntry 6 } mplsTunnelCHopIpv6PrefixLen OBJECT-TYPE SYNTAX Unsigned32 (0..128) MAX-ACCESS read-only STATUS current DESCRIPTION Srinivasan et al. Expires September 2001 [Page 42] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 "If mplsTunnelCHopAddrType is set to ipV6(2), this value will contain the prefix length for this hop's IPv6 address. This object is otherwise insignificant and should contain a value of 0." ::= { mplsTunnelCHopEntry 7 } mplsTunnelCHopAsNumber OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "If mplsTunnelCHopAddrType is set to asNumber(3), then this value will contain the AS number of this hop. This object is otherwise insignificant and should contain a value of 0 to indicate this fact." ::= { mplsTunnelCHopEntry 8 } mplsTunnelCHopType OBJECT-TYPE SYNTAX INTEGER { strict(1), loose(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Denotes whether this is tunnel hop is routed in a strict or loose fashion." ::= { mplsTunnelCHopEntry 9 } -- End of mplsTunnelCHopTable -- MPLS Tunnel Performance Table. mplsTunnelPerfTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsTunnelPerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides per-tunnel MPLS performance information." ::= { mplsTeObjects 9 } mplsTunnelPerfEntry OBJECT-TYPE SYNTAX MplsTunnelPerfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created by the LSR for every tunnel. Its is an extension to Srinivasan et al. Expires September 2001 [Page 43] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 mplsTunnelEntry." AUGMENTS { mplsTunnelEntry } ::= { mplsTunnelPerfTable 1 } MplsTunnelPerfEntry ::= SEQUENCE { mplsTunnelPerfPackets Counter32, mplsTunnelPerfHCPackets Counter64, mplsTunnelPerfErrors Counter32, mplsTunnelPerfBytes Counter32, mplsTunnelPerfHCBytes Counter64 } mplsTunnelPerfPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets forwarded by the tunnel." ::= { mplsTunnelPerfEntry 1 } mplsTunnelPerfHCPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "High capacity counter for number of packets forwarded by the tunnel." ::= { mplsTunnelPerfEntry 2 } mplsTunnelPerfErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of errored packets." ::= { mplsTunnelPerfEntry 3 } mplsTunnelPerfBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of bytes forwarded by the tunnel." ::= { mplsTunnelPerfEntry 4 } mplsTunnelPerfHCBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION Srinivasan et al. Expires September 2001 [Page 44] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 "High capacity counter for number of bytes forwarded by the tunnel." ::= { mplsTunnelPerfEntry 5 } -- End of mplsTunnelPerfTable -- CR-LDP Tunnel Resource Table mplsTunnelCRLDPResTable OBJECT-TYPE SYNTAX SEQUENCE OF MplsTunnelCRLDPResEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The mplsTunnelCRLDPResTable allows a manager to specify which CR-LDP-specific resources are desired for an MPLS tunnel if that tunnel is signaled using CR-LDP. Note that these attributes are in addition to those specified in mplsTunnelResourceTable. This table also allows several tunnels to point to a single entry in this table, implying that these tunnels should share resources." ::= { mplsTeObjects 10 } mplsTunnelCRLDPResEntry OBJECT-TYPE SYNTAX MplsTunnelCRLDPResEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents a set of resources for an MPLS tunnel established using CRLDP (mplsTunnelSignallingProto equal to crldp (3)). An entry can be created by a network administrator or by an SNMP agent as instructed by any MPLS signaling protocol." INDEX { mplsTunnelResourceIndex } ::= { mplsTunnelCRLDPResTable 1 } MplsTunnelCRLDPResEntry ::= SEQUENCE { mplsTunnelCRLDPResMeanBurstSize MplsBurstSize, mplsTunnelCRLDPResExcessBurstSize MplsBurstSize, mplsTunnelCRLDPResFrequency Integer32, mplsTunnelCRLDPResWeight Unsigned32, mplsTunnelCRLDPResFlags Unsigned32, mplsTunnelCRLDPResRowStatus RowStatus, mplsTunnelCRLDPResStorageType StorageType } mplsTunnelCRLDPResMeanBurstSize OBJECT-TYPE SYNTAX MplsBurstSize Srinivasan et al. Expires September 2001 [Page 45] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "The mean burst size in bytes." DEFVAL { 0 } ::= { mplsTunnelCRLDPResEntry 2 } mplsTunnelCRLDPResExcessBurstSize OBJECT-TYPE SYNTAX MplsBurstSize UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "The Excess burst size in bytes." REFERENCE "CR-LDP Specification, Section 4.3." DEFVAL { 0 } ::= { mplsTunnelCRLDPResEntry 3 } mplsTunnelCRLDPResFrequency OBJECT-TYPE SYNTAX INTEGER { unspecified(1), frequent(2), veryFrequent(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The granularity of the availability of committed rate." REFERENCE "CR-LDP Specification, Section 4.3." ::= { mplsTunnelCRLDPResEntry 4 } mplsTunnelCRLDPResWeight OBJECT-TYPE SYNTAX Unsigned32(0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The relative weight for using excess bandwidth above its committed rate. The value of 0 means that weight is not applicable for the CR-LSP." REFERENCE "CR-LDP Specification, Section 4.3." DEFVAL { 0 } ::= { mplsTunnelCRLDPResEntry 5 } mplsTunnelCRLDPResFlags OBJECT-TYPE SYNTAX Unsigned32 (0..63) Srinivasan et al. Expires September 2001 [Page 46] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 MAX-ACCESS read-create STATUS current DESCRIPTION "The value of the 1 byte Flags conveyed as part of the traffic parameters during the establishment of the CRLSP. The bits in this object are to be interpreted as follows. +--+--+--+--+--+--+--+--+ | Res |F6|F5|F4|F3|F2|F1| +--+--+--+--+--+--+--+--+ Res - These bits are reserved. Zero on transmission. Ignored on receipt. F1 - Corresponds to the PDR. F2 - Corresponds to the PBS. F3 - Corresponds to the CDR. F4 - Corresponds to the CBS. F5 - Corresponds to the EBS. F6 - Corresponds to the Weight. Each flag if is a Negotiable Flag corresponding to a Traffic Parameter. The Negotiable Flag value zero denotes Not Negotiable and value one denotes Negotiable." REFERENCE "Section 4.3, Constraint-Based LSP Setup using LDP, Jamoussi, et. al,, July 2000." DEFVAL { 0 } ::= { mplsTunnelCRLDPResEntry 6 } mplsTunnelCRLDPResRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table." ::= { mplsTunnelCRLDPResEntry 7 } mplsTunnelCRLDPResStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the storage type for this object." ::= { mplsTunnelCRLDPResEntry 8 } Srinivasan et al. Expires September 2001 [Page 47] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 -- Notifications. mplsTunnelTrapEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this object is true, then it enables the generation of mplsTunnelUp and mplsTunnelDown traps, otherwise these traps are not emitted." DEFVAL { false } ::= { mplsTeObjects 11 } mplsTunnelUp NOTIFICATION-TYPE OBJECTS { mplsTunnelIndex, mplsTunnelInstance, mplsTunnelIngressLSRId, mplsTunnelEgressLSRId, mplsTunnelAdminStatus, mplsTunnelOperStatus } STATUS current DESCRIPTION "This notification is generated when a mplsTunnelOperStatus object for one of the configured tunnels is about to leave the down state and transition into some other state (but not into the notPresent state). This other state is indicated by the included value of mplsTunnelOperStatus." ::= { mplsTeNotifyPrefix 1 } mplsTunnelDown NOTIFICATION-TYPE OBJECTS { mplsTunnelIndex, mplsTunnelInstance, mplsTunnelIngressLSRId, mplsTunnelEgressLSRId, mplsTunnelAdminStatus, mplsTunnelOperStatus } STATUS current DESCRIPTION "This notification is generated when a mplsTunnelOperStatus object for one of the configured tunnels is about to enter the down state from some other state (but not from the notPresent state). This other state is indicated by the Srinivasan et al. Expires September 2001 [Page 48] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 included value of mplsTunnelOperStatus." ::= { mplsTeNotifyPrefix 2 } mplsTunnelRerouted NOTIFICATION-TYPE OBJECTS { mplsTunnelIndex, mplsTunnelInstance, mplsTunnelIngressLSRId, mplsTunnelEgressLSRId, mplsTunnelAdminStatus, mplsTunnelOperStatus } STATUS current DESCRIPTION "This notification is generated when a tunnel is rerouted. If the actual path is used, then this object MAY contain the new path for this tunnel some time after this trap is issued by the agent." ::= { mplsTeNotifyPrefix 3 } mplsTunnelReoptimized NOTIFICATION-TYPE OBJECTS { mplsTunnelIndex, mplsTunnelInstance, mplsTunnelIngressLSRId, mplsTunnelEgressLSRId, mplsTunnelAdminStatus, mplsTunnelOperStatus } STATUS current DESCRIPTION "This notification is generated when a tunnel is reoptimized. If the actual path is used, then this object MAY contain the new path for this tunnel some time after this trap is issued by the agent." ::= { mplsTeNotifyPrefix 4 } -- End of notifications. -- Module compliance. mplsTeGroups OBJECT IDENTIFIER ::= { mplsTeConformance 1 } mplsTeCompliances OBJECT IDENTIFIER ::= { mplsTeConformance 2 } mplsTeModuleCompliance MODULE-COMPLIANCE STATUS current Srinivasan et al. Expires September 2001 [Page 49] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 DESCRIPTION "Compliance statement for agents that support the MPLS TE MIB." MODULE -- this module -- The mandatory group has to be implemented by all -- LSRs that originate/terminate ESLSPs/tunnels. -- In addition, depending on the type of tunnels -- supported, other groups become mandatory as -- explained below. MANDATORY-GROUPS { mplsTunnelGroup, mplsTunnelScalarGroup } GROUP mplsTunnelManualGroup DESCRIPTION "This group is mandatory for devices which support manual configuration of tunnels, in addition to mplsTunnelGroup. The following constraints apply: mplsTunnelSignallingProto should be at least read- only with a value of none(1)." GROUP mplsTunnelSignaledGroup DESCRIPTION "This group is mandatory for devices which support signaled tunnel set up, in addition to mplsTunnelGroup. The following constraints apply: mplsTunnelSignallingProto should be at least read- only returning a value of ldp(2), or rsvp(3)." GROUP mplsTunnelIsNotIntfcGroup DESCRIPTION "This group is mandatory for devices which support tunnels that are not interfaces, in addition to mplsTunnelGroup. The following constraints apply: mplsTunnelIsIf must at least be read-only returning false(1)." GROUP mplsTunnelIsIntfcGroup DESCRIPTION "This group is mandatory for devices which support tunnels that are interfaces, in addition to mplsTunnelGroup. The following constraints apply: mplsTunnelIsIf must at least be read-only returning true(2)." GROUP mplsTunnelOptionalGroup DESCRIPTION Srinivasan et al. Expires September 2001 [Page 50] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 "Objects in this group are optional." -- mplsTunnelTable OBJECT mplsTunnelName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelDescr MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelIsIf MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelIfIndex DESCRIPTION "Write access is not required." OBJECT mplsTunnelXCPointer MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelSignallingProto MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelSetupPrio MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelHoldingPrio MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelSessionAttributes MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelOwner MIN-ACCESS read-only Srinivasan et al. Expires September 2001 [Page 51] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 DESCRIPTION "Write access is not required." OBJECT mplsTunnelLocalProtectInUse MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelResourcePointer MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelInstancePriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelHopTableIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelPrimaryInstance MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelPrimaryTimeUp MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelPathChanges MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelLastPathChange MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelCreationTime MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelStateTransitions MIN-ACCESS read-only Srinivasan et al. Expires September 2001 [Page 52] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 DESCRIPTION "Write access is not required." OBJECT mplsTunnelARHopTableIndex DESCRIPTION "Write access is not required." OBJECT mplsTunnelCHopTableIndex DESCRIPTION "Write access is not required." OBJECT mplsTunnelAdminStatus SYNTAX INTEGER { up (1), down (2) } MIN-ACCESS read-only DESCRIPTION "Only up and down states must be supported. Write access is not required." OBJECT mplsTunnelOperStatus SYNTAX INTEGER { up (1), down (2) } DESCRIPTION "Only up and down states must be supported. Write access is not required." OBJECT mplsTunnelRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported. Write access is not required." OBJECT mplsTunnelStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other (1) needs to be supported." OBJECT mplsTunnelPathInUse MIN-ACCESS read-only DESCRIPTION "Read-only support is required." OBJECT mplsTunnelRole SYNTAX INTEGER { head(1) } MIN-ACCESS read-only Srinivasan et al. Expires September 2001 [Page 53] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 DESCRIPTION "Only support for head is required." OBJECT mplsTunnelTotalUpTime MIN-ACCESS read-only DESCRIPTION "Read-only support is required." OBJECT mplsTunnelInstanceUpTime MIN-ACCESS read-only DESCRIPTION "Read-only support is required." -- mplsTunnelHopTable OBJECT mplsTunnelHopAddrType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelHopIpv4Addr MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelHopIpv4PrefixLen MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelHopIpv6Addr MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelHopIpv6PrefixLen MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelHopAsNumber MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelHopLspId MIN-ACCESS read-only DESCRIPTION "Write access is not required." Srinivasan et al. Expires September 2001 [Page 54] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 OBJECT mplsTunnelHopType SYNTAX INTEGER { strict(1) } MIN-ACCESS read-only DESCRIPTION "loose(2) need not be supported. Write access is not required." OBJECT mplsTunnelHopIncludeExclude MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelHopPathOptionName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelHopEntryPathComp MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelHopRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported. Write access is not required." OBJECT mplsTunnelHopStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other (1) needs to be supported." -- mplsTunnelResourceTable OBJECT mplsTunnelResourceMaxRate MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelResourceMeanRate MIN-ACCESS read-only DESCRIPTION Srinivasan et al. Expires September 2001 [Page 55] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 "Write access is not required." OBJECT mplsTunnelResourceMaxBurstSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelResourceMeanBurstSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelResourceExcessBurstSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelResourceFrequency MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelResourceWeight MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelResourceRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported. Write access is not required." OBJECT mplsTunnelResourceStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other (1) needs to be supported." -- mplsTunnelPerfTable OBJECT mplsTunnelPerfPackets MIN-ACCESS read-only DESCRIPTION Srinivasan et al. Expires September 2001 [Page 56] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 "Write access is not required." OBJECT mplsTunnelPerfHCPackets MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelPerfErrors MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelPerfBytes MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT mplsTunnelPerfHCBytes MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { mplsTeCompliances 1 } -- Units of conformance. mplsTunnelGroup OBJECT-GROUP OBJECTS { mplsTunnelIndexNext, mplsTunnelName, mplsTunnelDescr, mplsTunnelOwner, mplsTunnelXCPointer, mplsTunnelIfIndex, mplsTunnelHopTableIndex, mplsTunnelARHopTableIndex, mplsTunnelCHopTableIndex, mplsTunnelAdminStatus, mplsTunnelOperStatus, mplsTunnelRowStatus, mplsTunnelTrapEnable, mplsTunnelStorageType, mplsTunnelConfigured, mplsTunnelActive, mplsTunnelPrimaryInstance, mplsTunnelPrimaryTimeUp, mplsTunnelPathChanges, mplsTunnelLastPathChange, mplsTunnelCreationTime, Srinivasan et al. Expires September 2001 [Page 57] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 mplsTunnelStateTransitions, mplsTunnelEgressLSRId, mplsTunnelIncludeAnyAffinity, mplsTunnelIncludeAllAffinity, mplsTunnelExcludeAllAffinity, mplsTunnelPerfPackets, mplsTunnelPerfHCPackets, mplsTunnelPerfErrors, mplsTunnelPerfBytes, mplsTunnelPerfHCBytes, mplsTunnelResourcePointer, mplsTunnelInstancePriority, mplsTunnelPathInUse, mplsTunnelRole, mplsTunnelTotalUpTime, mplsTunnelInstanceUpTime } STATUS current DESCRIPTION "Necessary, but not sufficient, set of objects to implement tunnels. In addition, depending on the type of the tunnels supported (for example, manually configured or signaled, persistent or non- persistent, etc.), the following other groups defined below are mandatory: mplsTunnelManualGroup and/or mplsTunnelSignaledGroup, mplsTunnelIsNotIntfcGroup and/or mplsTunnelIsIntfcGroup." ::= { mplsTeGroups 1 } mplsTunnelManualGroup OBJECT-GROUP OBJECTS { mplsTunnelSignallingProto } STATUS current DESCRIPTION "Object(s) needed to implement manually configured tunnels." ::= { mplsTeGroups 2 } mplsTunnelSignaledGroup OBJECT-GROUP OBJECTS { mplsTunnelSetupPrio, mplsTunnelHoldingPrio, mplsTunnelSignallingProto, mplsTunnelLocalProtectInUse, mplsTunnelSessionAttributes, mplsTunnelHopListIndexNext, mplsTunnelHopAddrType, mplsTunnelHopIpv4Addr, mplsTunnelHopIpv4PrefixLen, mplsTunnelHopIpv6Addr, Srinivasan et al. Expires September 2001 [Page 58] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 mplsTunnelHopIpv6PrefixLen, mplsTunnelHopAsNumber, mplsTunnelHopLspId, mplsTunnelHopType, mplsTunnelHopIncludeExclude, mplsTunnelHopPathOptionName, mplsTunnelHopEntryPathComp, mplsTunnelHopRowStatus, mplsTunnelHopStorageType } STATUS current DESCRIPTION "Object needed to implement signaled tunnels." ::= { mplsTeGroups 3 } mplsTunnelScalarGroup OBJECT-GROUP OBJECTS { mplsTunnelConfigured, mplsTunnelActive, mplsTunnelTEDistProto, mplsTunnelMaxHops } STATUS current DESCRIPTION "Scalar object needed to implement MPLS tunnels." ::= { mplsTeGroups 4 } mplsTunnelIsIntfcGroup OBJECT-GROUP OBJECTS { mplsTunnelIsIf } STATUS current DESCRIPTION "Objects needed to implement tunnels that are interfaces." ::= { mplsTeGroups 5 } mplsTunnelIsNotIntfcGroup OBJECT-GROUP OBJECTS { mplsTunnelIsIf } STATUS current DESCRIPTION "Objects needed to implement tunnels that are not interfaces." ::= { mplsTeGroups 6 } mplsTunnelOptionalGroup OBJECT-GROUP OBJECTS { mplsTunnelResourceIndexNext, mplsTunnelResourceMaxRate, mplsTunnelResourceMeanRate, mplsTunnelResourceMaxBurstSize, mplsTunnelResourceMeanBurstSize, Srinivasan et al. Expires September 2001 [Page 59] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 mplsTunnelResourceExcessBurstSize, mplsTunnelResourceFrequency, mplsTunnelResourceWeight, mplsTunnelResourceRowStatus, mplsTunnelResourceStorageType, mplsTunnelARHopAddrType, mplsTunnelARHopIpv4Addr, mplsTunnelARHopIpv4PrefixLen, mplsTunnelARHopIpv6Addr, mplsTunnelARHopIpv6PrefixLen, mplsTunnelARHopAsNumber, mplsTunnelCHopAddrType, mplsTunnelCHopIpv4Addr, mplsTunnelCHopIpv4PrefixLen, mplsTunnelCHopIpv6Addr, mplsTunnelCHopIpv6PrefixLen, mplsTunnelCHopAsNumber, mplsTunnelCHopType } STATUS current DESCRIPTION "The objects in this group are optional." ::= { mplsTeGroups 7 } mplsTunnelCRLDPResOptionalGroup OBJECT-GROUP OBJECTS { mplsTunnelCRLDPResMeanBurstSize, mplsTunnelCRLDPResExcessBurstSize, mplsTunnelCRLDPResFrequency, mplsTunnelCRLDPResWeight, mplsTunnelCRLDPResFlags, mplsTunnelCRLDPResRowStatus, mplsTunnelCRLDPResStorageType } STATUS current DESCRIPTION "Set of objects implemented for resources applicable for tunnels signaled using CR-LDP." ::= { mplsTeGroups 8 } mplsTeNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { mplsTunnelUp, mplsTunnelDown, mplsTunnelRerouted, mplsTunnelReoptimized } STATUS current DESCRIPTION "Set of notifications implemented in this module. Srinivasan et al. Expires September 2001 [Page 60] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 None is mandatory." ::= { mplsTeGroups 9 } -- End of MPLS-TE-MIB END 11. Security Considerations There are a number of management objects defined in this MIB that have a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. It is thus important to control even GET access to these objects and possibly to even encrypt the values of these object when sending them over the network via SNMP. Not all versions of SNMP provide features for such a secure environment. SNMPv1 by itself is not a secure environment. Even if the network itself is secure (for example by using IPSec [IPSEC]), there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB. It is recommended that the implementers consider the security features as provided by the SNMPv3 framework. Specifically, the use of the User-based Security Model [SNMPv3USM] and the View- based Access Control [SNMPv3VACM] is recommended. It is then a customer/user responsibility to ensure that the SNMP entity giving access to an instance of this MIB, is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 12. Acknowledgments We wish to thank Adrian Farrel, Eric Gray, Joan Cucchiara, Patrick Kerharo, Paul Langille and Mike Piecuch for their comments on this draft. 13. References [MPLSArch] Rosen, E., Viswanathan, A., and R. Callon, Srinivasan et al. Expires September 2001 [Page 61] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 "Multiprotocol Label Switching Architecture", Internet Draft , July 2000. [LSRMIB] Srinivasan, C., Viswanathan, A. and T. Nadeau, "MPLS Label Switch Router Management Information Base Using SMIv2", Internet Draft , July 2000. [LblStk] Rosen, E., Rekhter, Y., Tappan, D., Farinacci, D., Federokow, G., Li, T., and A. Conta, "MPLS Label Stack Encoding", Internet Draft , July 2000. [RSVPTun] Awaduche, D., Berger, L., Der-Haw, G., Li, T., Swallow, G., and V. Srinivasan, "Extensions to RSVP for LSP Tunnels", Internet Draft , August 2000. [CR-LDP] B. Jamoussi (Editor), "Constraint-Based LSP Setup using LDP", Internet Draft , July 2000. [Assigned] Reynolds, J., and J. Postel, "Assigned Numbers", RFC 1700, October 1994. See also: http://www.isi.edu/in- notes/iana/assignments/smi-numbers [SNMPArch] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for Describing SNMP Management Frameworks", RFC 2271, January 1998. [SMIv1] Rose, M., and K. McCloghrie, "Structure and Identification of Management Information for TCP/IP-based Internets", RFC 1155, May 1990. [SNMPv1MIBDef]Rose, M., and K. McCloghrie, "Concise MIB Definitions", RFC 1212, March 1991. [SNMPv1Traps] M. Rose, "A Convention for Defining Traps for use with the SNMP", RFC 1215, March 1991. [SMIv2] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure of Management Information for Version 2 of the Simple Srinivasan et al. Expires September 2001 [Page 62] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 Network Management Protocol (SNMPv2)", RFC 1902, January 1996. [SNMPv2TC] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual Conventions for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1903, SNMP Research, Inc., Cisco Systems, Inc., January 1996. [SNMPv2Conf] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Conformance Statements for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1904, January 1996. [SNMPv1] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network Management Protocol", RFC 1157, May 1990. [SNMPv2c] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Introduction to Community-based SNMPv2", RFC 1901, January 1996. [SNMPv2TM] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1906, January 1996. [SNMPv3MP] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)", RFC 2272, January 1998. [SNMPv3USM] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", RFC 2574, April 1999. [SNMPv2PO] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1905, January 1996. [SNMPv3App] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC 2273, January 1998. [SNMPv3VACM] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", RFC 2575, April 1999. Srinivasan et al. Expires September 2001 [Page 63] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 [IPSEC] Kent, S., and Atkinson, R., "Security Architecture for the Internet Protocol", RFC 2401, November 1998. [IFMIB] McCloghrie, K., and F. Kastenholtz, "The Interfaces Group MIB using SMIv2", RFC 2233, Nov. 1997. [INETADDRMIB] Daniele, M., Haberman, B., Routhier, S. and J. Schoenwaelder, "Textual Conventions for Internet Network Addresses", RFC 2851, June 2000. 14. Authors' Addresses Cheenu Srinivasan Tachion Networks, Inc. Monmouth Park Corporate Center I Building C, 185 Monmouth Park Highway West Long Branch, NJ 07764 Phone: +1-732-542-7750 x1234 Email: cheenu@tachion.com Arun Viswanathan Force10 Networks, Inc. 1440 McCarthy Blvd Milpitas, CA 95035 Phone: +1-408-571-3516 Email: arun@force10networks.com Thomas D. Nadeau Cisco Systems, Inc. 300 Apollo Drive Chelmsford, MA 01824 Phone: +1-978-244-3051 Email: tnadeau@cisco.com 15. Full Copyright Statement Copyright (C) The Internet Society (2000). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on Srinivasan et al. Expires September 2001 [Page 64] Internet Draft MPLS Traffic Engineering MIB 2 March 2001 all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Srinivasan et al. Expires September 2001 [Page 65]