Network File System Version 4 C. Lever, Ed. Internet-Draft Oracle Obsoletes: 5667 (if approved) August 25, 2016 Intended status: Standards Track Expires: February 26, 2017 Network File System (NFS) Upper Layer Binding To RPC-Over-RDMA draft-ietf-nfsv4-rfc5667bis-02 Abstract This document specifies Upper Layer Bindings of Network File System (NFS) protocol versions to RPC-over-RDMA transports. These bindings are required to enable RPC-based protocols to use direct data placement on RPC-over-RDMA transports. This document obsoletes RFC 5667. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on February 26, 2017. Copyright Notice Copyright (c) 2016 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of Lever Expires February 26, 2017 [Page 1] Internet-Draft NFS On RPC-Over-RDMA August 2016 the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1. Changes Since RFC 5667 . . . . . . . . . . . . . . . . . 3 1.2. Extending This Upper Layer Binding . . . . . . . . . . . 4 1.3. Requirements Language . . . . . . . . . . . . . . . . . . 4 2. Conveying NFS Operations On RPC-Over-RDMA Transports . . . . 4 2.1. Use Of The Read List . . . . . . . . . . . . . . . . . . 4 2.2. Use Of The Write List . . . . . . . . . . . . . . . . . . 4 2.3. Construction Of Individual Chunks . . . . . . . . . . . . 5 2.4. Use Of Long Calls And Replies . . . . . . . . . . . . . . 5 3. NFS Versions 2 And 3 Upper Layer Binding . . . . . . . . . . 5 4. NFS Version 4 Upper Layer Binding . . . . . . . . . . . . . . 6 4.1. DDP-Eligibility . . . . . . . . . . . . . . . . . . . . . 6 4.2. Reply Size Estimation . . . . . . . . . . . . . . . . . . 7 4.3. NFS Version 4 COMPOUND Considerations . . . . . . . . . . 7 4.4. NFS Version 4 Callback . . . . . . . . . . . . . . . . . 9 5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 9 6. Security Considerations . . . . . . . . . . . . . . . . . . . 10 7. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 10 8. References . . . . . . . . . . . . . . . . . . . . . . . . . 10 8.1. Normative References . . . . . . . . . . . . . . . . . . 10 8.2. Informative References . . . . . . . . . . . . . . . . . 11 Author's Address . . . . . . . . . . . . . . . . . . . . . . . . 12 1. Introduction An RPC-over-RDMA transport, such as defined in [I-D.ietf-nfsv4-rfc5666bis], may employ direct data placement to transmit large data payloads associated with RPC transactions. Each RPC-over-RDMA transport header conveys lists of memory locations corresponding to XDR data items defined in an Upper Layer Protocol (such as NFS). To facilitate interoperation, RPC client and server implementations must agree in advance on what XDR data items in which RPC procedures are eligible for direct data placement (DDP). This document contains material required of Upper Layer Bindings, as specified in [I-D.ietf-nfsv4-rfc5666bis], for the following NFS protocol versions: o NFS Version 2 [RFC1094] o NFS Version 3 [RFC1813] o NFS Version 4.0 [RFC7530] Lever Expires February 26, 2017 [Page 2] Internet-Draft NFS On RPC-Over-RDMA August 2016 o NFS Version 4.1 [RFC5661] o NFS Version 4.2 [I-D.ietf-nfsv4-minorversion2] 1.1. Changes Since RFC 5667 Corrections and updates made necessary by new language in [I-D.ietf-nfsv4-rfc5666bis] have been introduced. For example, references to deprecated features of RPC-over-RDMA Version One, such as RDMA_MSGP, and the use of the Read list for handling RPC replies, has been removed. The term "mapping" has been replaced with the term "binding" or "Upper Layer Binding" throughout the document. Material that duplicates what is in [I-D.ietf-nfsv4-rfc5666bis] has been deleted. Material required by [I-D.ietf-nfsv4-rfc5666bis] for Upper Layer Bindings that was not present in [RFC5667] has been added, including discussion of how each NFS version properly estimates the maximum size of RPC replies. The following changes have been made, relative to [RFC5667]: o Ambiguous or erroneous uses of RFC2119 terms have been corrected. o References to specific data movement mechanisms have been made generic or removed. o References to obsolete RFCs have been replaced. o Technical corrections have been made. For example, the mention of 12KB and 36KB inline thresholds have been removed. The reference to a non-existant NFS version 4 SYMLINK operation has been replaced with NFS version 4 CREATE(NF4LNK). The discussion of NFS version 4 COMPOUND handling has been completed. o An IANA Considerations Section has replaced the "Port Usage Considerations" Section. o Code excerpts have been removed, and figures have been modernized. o Language inconsistent with or contradictory to [I-D.ietf-nfsv4-rfc5666bis] has been removed from Sections 2 and 3, and both Sections have been combined into Section 2 in the present document. o An explicit discussion of NFSv4.0 and NFSv4.1 backchannel operation will replace the previous treatment of callback operations. No NFSv4.x callback operation is DDP-eligible. Lever Expires February 26, 2017 [Page 3] Internet-Draft NFS On RPC-Over-RDMA August 2016 o The binding for NFSv4.1 has been completed. No DDP-eligible operations exist in NFSv4.1 that did not exist in NFSv4.0. o A binding for NFSv4.2 has been added that includes discussion of new data-bearing operations like READ_PLUS. 1.2. Extending This Upper Layer Binding As stated earlier, RPC programs such as NFS are required to have an Upper Layer Binding specification to interoperate on RPC-over-RDMA transports [I-D.ietf-nfsv4-rfc5666bis]. The Upper Layer Binding specified in this document can be extended to cover versions of the NFS version 4 protocol specified after NFS version 4 minor version 2 via standards action. This includes NFSv4 extensions that are documented separately from a new minor version. 1.3. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. 2. Conveying NFS Operations On RPC-Over-RDMA Transports Definitions of terminology and a general discussion of how RPC-over- RDMA is used to convey RPC transactions can be found in [I-D.ietf-nfsv4-rfc5666bis]. In this section, these general principals are applied to the specifics of the NFS protocol. 2.1. Use Of The Read List The Read list in each RPC-over-RDMA transport header represents a set of memory regions containing DDP-eligible NFS argument data. Large data items, such as the data payload of an NFS WRITE request, are referenced by the Read list. The server places these directly into its memory. XDR unmarshaling code on the NFS server identifies the correspondence between Read chunks and particular NFS arguments via the chunk Position value encoded in each Read chunk. 2.2. Use Of The Write List The Write list in each RPC-over-RDMA transport header represents a set of memory regions that can receive DDP-eligible NFS result data. Large data items such as the payload of an NFS READ request are referenced by the Write list. The server places these directly into client memory. Lever Expires February 26, 2017 [Page 4] Internet-Draft NFS On RPC-Over-RDMA August 2016 Each Write chunk corresponds to a specific XDR data item in an NFS reply. This document specifies how NFS client and server implementations identify the correspondence between Write chunks and XDR results. 2.3. Construction Of Individual Chunks Each Read chunk is represented as a list of segments at the same XDR Position, and each Write chunk is represented as an array of segments. An NFS client thus has the flexibility to advertise a set of discontiguous memory regions in which to send or receive a single DDP-eligible data item. 2.4. Use Of Long Calls And Replies Small RPC messages are conveyed using RDMA Send operations which are of limited size. If an NFS request is too large to be conveyed via an RDMA Send, and there are no DDP-eligible data items that can be removed, an NFS client must send the request using a Long Call. The entire NFS request is sent in a special Read chunk called a Position- Zero Read chunk. If a client predicts that the maximum size of an NFS reply is too large to be conveyed via an RDMA Send, it provides a Reply chunk in the RPC-over-RDMA transport header conveying the NFS request. The server can place the entire NFS reply in the Reply chunk. These special chunks are described in more detail in [I-D.ietf-nfsv4-rfc5666bis]. 3. NFS Versions 2 And 3 Upper Layer Binding An NFS client MAY send a single Read chunk to supply opaque file data for an NFS WRITE procedure, or the pathname for an NFS SYMLINK procedure. For all other NFS procedures, NFS servers MUST ignore Read chunks that have a non-zero value in their Position fields, and Read chunks beyond the first in the Read list. Similarly, an NFS client MAY provide a single Write chunk to receive either opaque file data from an NFS READ procedure, or the pathname from an NFS READLINK procedure. NFS servers MUST ignore the Write list for any other NFS procedure, and any Write chunks beyond the first in the Write list. There are no NFS version 2 or 3 procedures that have DDP-eligible data items in both their Call and Reply. However, when an NFS client sends a Long Call or Reply, it MAY provide a combination of Read Lever Expires February 26, 2017 [Page 5] Internet-Draft NFS On RPC-Over-RDMA August 2016 list, Write list, and/or a Reply chunk in the same RPC-over-RDMA header. If an NFS client has not provided enough bytes in a Read list to match the size of a DDP-eligible NFS argument data item, or if an NFS client has not provided enough Write list resources to handle an NFS WRITE or READLINK reply, or if the client has not provided a large enough Reply chunk to convey an NFS reply, the server MUST return one of: o An RPC-over-RDMA message of type RDMA_ERROR, with the rdma_xid field set to the XID of the matching NFS Call, and the rdma_error field set to ERR_CHUNK; or o An RPC message with the mtype field set to REPLY, the stat field set to MSG_ACCEPTED, and the accept_stat field set to GARBAGE_ARGS. NFS clients already successfully estimate the maximum reply size of each operation in order to provide an adequate set of buffers to receive each NFS reply. An NFS client provides a Reply chunk when the maximum possible reply size is larger than the client's responder inline threshold. 4. NFS Version 4 Upper Layer Binding This specification applies to NFS Version 4.0 [RFC7530], NFS Version 4.1 [RFC5661], and NFS Version 4.2 [I-D.ietf-nfsv4-minorversion2]. It also applies to the callback protocols associated with each of these minor versions. 4.1. DDP-Eligibility An NFS client MAY send a Read chunk to supply opaque file data for a WRITE operation or the pathname for a CREATE(NF4LNK) operation in an NFS version 4 COMPOUND procedure. An NFS client MUST NOT send a Read chunk that corresponds with any other XDR data item in any other NFS version 4 operation in an NFS version 4 COMPOUND procedure, or in an NFS version 4 NULL procedure. Similarly, an NFS client MAY provide a Write chunk to receive either opaque file data from a READ operation, NFS4_CONTENT_DATA from a READ_PLUS operation, or the pathname from a READLINK operation in an NFS version 4 COMPOUND procedure. An NFS client MUST NOT provide a Write chunk that corresponds with any other XDR data item in any other NFS version 4 operation in an NFS version 4 COMPOUND procedure, or in an NFS version 4 NULL procedure. Lever Expires February 26, 2017 [Page 6] Internet-Draft NFS On RPC-Over-RDMA August 2016 There is no prohibition against an NFS version 4 COMPOUND procedure constructed with both a READ and WRITE operation, say. Thus it is possible for NFS version 4 COMPOUND procedures to use both the Read list and Write list simultaneously. An NFS client MAY provide a Read list and a Write list in the same transaction if it is sending a Long Call or Reply. If an NFS client has not provided enough bytes in a Read list to match the size of a DDP-eligible NFS argument data item, or if an NFS client has not provided enough Write list resources to handle a WRITE or READLINK operation, or if the client has not provided a large enough Reply chunk to convey an NFS reply, the server MUST return one of: o An RPC-over-RDMA message of type RDMA_ERROR, with the rdma_xid field set to the XID of the matching NFS Call, and the rdma_error field set to ERR_CHUNK; or o An RPC message with the mtype field set to REPLY, the stat field set to MSG_ACCEPTED, and the accept_stat field set to GARBAGE_ARGS. 4.2. Reply Size Estimation An NFS client provides a Reply chunk when the maximum possible reply size is larger than the client's responder inline threshold. NFS clients successfully estimate the maximum reply size of most operations in order to provide an adequate set of buffers to receive each NFS reply. There are certain NFSv4 data items whose size cannot be reliably estimated by clients, however, because there is no protocol-specified size limit on these structures. These include but are not limited to opaque types such as the attrlist4 field; fields containing ACLs such as fattr4_acl, fattr4_dacl, fattr4_sacl; fields in the fs_locations4 and fs_locations_info4 data structures; and opaque fields loc_body, loh_body, da_addr_body, lou_body, lrf_body, fattr_layout_types and fs_layout_types, which pertain to pNFS layout metadata. 4.3. NFS Version 4 COMPOUND Considerations An NFS version 4 COMPOUND procedure supplies arguments for a sequence of operations, and returns results from that sequence. A client MAY construct an NFS version 4 COMPOUND procedure that uses more than one chunk in either the Read list or Write list. The NFS client provides XDR Position values in each Read chunk to disambiguate which chunk is associated with which XDR data item. Lever Expires February 26, 2017 [Page 7] Internet-Draft NFS On RPC-Over-RDMA August 2016 However NFS server and client implementations must agree in advance on how to pair Write chunks with returned result data items. The mechanism specified in [I-D.ietf-nfsv4-rfc5666bis]) is applied here: o The first chunk in the Write list MUST be used by the first READ or READLINK operation in an NFS version 4 COMPOUND procedure. The next Write chunk is used by the next READ or READLINK, and so on. o If there are more READ or READLINK operations than Write chunks, then any remaining operations MUST return their results inline. o If an NFS client presents a Write chunk, then the corresponding READ or READLINK operation MUST return its data by placing data into that chunk. o If the Write chunk has zero RDMA segments, or if the total size of the segments is zero, then the corresponding READ or READLINK operation MUST return its result inline. The following example shows a Write list with three Write chunks, A, B, and C. The server consumes the provided Write chunks by writing the results of the designated operations in the compound request, READ and READLINK, back to each chunk. Write list: A --> B --> C NFS version 4 COMPOUND request: PUTFH LOOKUP READ PUTFH LOOKUP READLINK PUTFH LOOKUP READ | | | v v v A B C If the client does not want to have the READLINK result returned directly, it provides a zero-length array of segment triplets for buffer B or sets the values in the segment triplet for buffer B to zeros to indicate that the READLINK result must be returned inline. Unlike NFS versions 2 and 3, the maximum size of an NFS version 4 COMPOUND is not bounded. However, typical NFS version 4 clients rarely issue such problematic requests. In practice, NFS version 4 clients behave in much more predictable ways. Rsize and wsize apply to COMPOUND operations by capping the total amount of data payload allowed in each COMPOUND. An extension to NFS version 4 supporting a Lever Expires February 26, 2017 [Page 8] Internet-Draft NFS On RPC-Over-RDMA August 2016 comprehensive exchange of upper-layer message size parameters is part of [RFC5661]. 4.4. NFS Version 4 Callback The NFS version 4 protocols support server-initiated callbacks to notify clients of events such as recalled delegations. There are no DDP-eligible data items in callback protocols associated with NFSv4.0, NFSv4.1, or NFSv4.2. In NFS version 4.1 and 4.2, callback operations may appear on the same connection as one used for NFS version 4 client requests. NFS version 4 clients and servers MUST use the mechanism described in [I-D.ietf-nfsv4-rpcrdma-bidirection] when backchannel operations are conveyed on RPC-over-RDMA transports. 5. IANA Considerations NFS use of direct data placement introduces a need for an additional NFS port number assignment for networks that share traditional UDP and TCP port spaces with RDMA services. The iWARP [RFC5041] [RFC5040] protocol is such an example (InfiniBand is not). NFS servers for versions 2 and 3 [RFC1094] [RFC1813] traditionally listen for clients on UDP and TCP port 2049, and additionally, they register these with the portmapper and/or rpcbind [RFC1833] service. However, [RFC7530] requires NFS servers for version 4 to listen on TCP port 2049, and they are not required to register. An NFS version 2 or version 3 server supporting RPC-over-RDMA on such a network and registering itself with the RPC portmapper MAY choose an arbitrary port, or MAY use the alternative well-known port number for its RPC-over-RDMA service. The chosen port MAY be registered with the RPC portmapper under the netid assigned by the requirement in [I-D.ietf-nfsv4-rfc5666bis]. An NFS version 4 server supporting RPC-over-RDMA on such a network MUST use the alternative well-known port number for its RPC-over-RDMA service. Clients SHOULD connect to this well-known port without consulting the RPC portmapper (as for NFSv4/TCP). The port number assigned to an NFS service over an RPC-over-RDMA transport is available from the IANA port registry [RFC3232]. Lever Expires February 26, 2017 [Page 9] Internet-Draft NFS On RPC-Over-RDMA August 2016 6. Security Considerations The RDMA transport for RPC [I-D.ietf-nfsv4-rfc5666bis] supports all RPC [RFC5531] security models, including RPCSEC_GSS [RFC2203] security and transport-level security. The choice of RDMA Read and RDMA Write to convey RPC argument and results does not affect this, since it only changes the method of data transfer. Specifically, the requirements of [I-D.ietf-nfsv4-rfc5666bis] ensure that this choice does not introduce new vulnerabilities. Because this document defines only the binding of the NFS protocols atop [I-D.ietf-nfsv4-rfc5666bis], all relevant security considerations are therefore to be described at that layer. 7. Acknowledgments The author gratefully acknowledges the work of Brent Callaghan and Tom Talpey on the original NFS Direct Data Placement specification [RFC5667]. The author also wishes to thank Bill Baker and Greg Marsden for their support of this work. Dave Noveck provided excellent review, constructive suggestions, and consistent navigational guidance throughout the process of drafting this document. Special thanks go to nfsv4 Working Group Chair Spencer Shepler and nfsv4 Working Group Secretary Thomas Haynes for their support. 8. References 8.1. Normative References [I-D.ietf-nfsv4-minorversion2] Haynes, T., "NFS Version 4 Minor Version 2", draft-ietf- nfsv4-minorversion2-41 (work in progress), January 2016. [I-D.ietf-nfsv4-rfc5666bis] Lever, C., Simpson, W., and T. Talpey, "Remote Direct Memory Access Transport for Remote Procedure Call, Version One", draft-ietf-nfsv4-rfc5666bis-07 (work in progress), May 2016. [I-D.ietf-nfsv4-rpcrdma-bidirection] Lever, C., "Bi-directional Remote Procedure Call On RPC- over-RDMA Transports", draft-ietf-nfsv4-rpcrdma- bidirection-05 (work in progress), June 2016. Lever Expires February 26, 2017 [Page 10] Internet-Draft NFS On RPC-Over-RDMA August 2016 [RFC1833] Srinivasan, R., "Binding Protocols for ONC RPC Version 2", RFC 1833, DOI 10.17487/RFC1833, August 1995, . [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC2203] Eisler, M., Chiu, A., and L. Ling, "RPCSEC_GSS Protocol Specification", RFC 2203, DOI 10.17487/RFC2203, September 1997, . [RFC5531] Thurlow, R., "RPC: Remote Procedure Call Protocol Specification Version 2", RFC 5531, DOI 10.17487/RFC5531, May 2009, . [RFC5661] Shepler, S., Ed., Eisler, M., Ed., and D. Noveck, Ed., "Network File System (NFS) Version 4 Minor Version 1 Protocol", RFC 5661, DOI 10.17487/RFC5661, January 2010, . [RFC7530] Haynes, T., Ed. and D. Noveck, Ed., "Network File System (NFS) Version 4 Protocol", RFC 7530, DOI 10.17487/RFC7530, March 2015, . 8.2. Informative References [RFC1094] Nowicki, B., "NFS: Network File System Protocol specification", RFC 1094, DOI 10.17487/RFC1094, March 1989, . [RFC1813] Callaghan, B., Pawlowski, B., and P. Staubach, "NFS Version 3 Protocol Specification", RFC 1813, DOI 10.17487/RFC1813, June 1995, . [RFC3232] Reynolds, J., Ed., "Assigned Numbers: RFC 1700 is Replaced by an On-line Database", RFC 3232, DOI 10.17487/RFC3232, January 2002, . [RFC5040] Recio, R., Metzler, B., Culley, P., Hilland, J., and D. Garcia, "A Remote Direct Memory Access Protocol Specification", RFC 5040, DOI 10.17487/RFC5040, October 2007, . Lever Expires February 26, 2017 [Page 11] Internet-Draft NFS On RPC-Over-RDMA August 2016 [RFC5041] Shah, H., Pinkerton, J., Recio, R., and P. Culley, "Direct Data Placement over Reliable Transports", RFC 5041, DOI 10.17487/RFC5041, October 2007, . [RFC5667] Talpey, T. and B. Callaghan, "Network File System (NFS) Direct Data Placement", RFC 5667, DOI 10.17487/RFC5667, January 2010, . Author's Address Charles Lever (editor) Oracle Corporation 1015 Granger Avenue Ann Arbor, MI 48104 USA Phone: +1 734 274 2396 Email: chuck.lever@oracle.com Lever Expires February 26, 2017 [Page 12]