This is a purely informative rendering of an RFC that includes verified errata. This rendering may not be used as a reference.

The following 'Verified' errata have been incorporated in this document: EID 576, EID 577
Network Working Group                                          J. Postel
Request for Comments:  792                                           ISI
                                                          September 1981
Updates:  RFCs 777, 760
Updates:  IENs 109, 128

                   INTERNET CONTROL MESSAGE PROTOCOL

                         DARPA INTERNET PROGRAM
                         PROTOCOL SPECIFICATION



Introduction

   The Internet Protocol (IP) [1] is used for host-to-host datagram
   service in a system of interconnected networks called the
   Catenet [2].  The network connecting devices are called Gateways.
   These gateways communicate between themselves for control purposes
   via a Gateway to Gateway Protocol (GGP) [3,4].  Occasionally a
   gateway or destination host will communicate with a source host, for
   example, to report an error in datagram processing.  For such
   purposes this protocol, the Internet Control Message Protocol (ICMP),
   is used.  ICMP, uses the basic support of IP as if it were a higher
   level protocol, however, ICMP is actually an integral part of IP, and
   must be implemented by every IP module.

   ICMP messages are sent in several situations:  for example, when a
   datagram cannot reach its destination, when the gateway does not have
   the buffering capacity to forward a datagram, and when the gateway
   can direct the host to send traffic on a shorter route.

   The Internet Protocol is not designed to be absolutely reliable.  The
   purpose of these control messages is to provide feedback about
   problems in the communication environment, not to make IP reliable.
   There are still no guarantees that a datagram will be delivered or a
   control message will be returned.  Some datagrams may still be
   undelivered without any report of their loss.  The higher level
   protocols that use IP must implement their own reliability procedures
   if reliable communication is required.

   The ICMP messages typically report errors in the processing of
   datagrams.  To avoid the infinite regress of messages about messages
   etc., no ICMP messages are sent about ICMP messages.  Also ICMP messages are only sent about errors in handling fragment zero of 
fragmented datagrams.  (Fragment zero has the fragment offset equal
zero).
EID 576 (Verified) is as follows:

Section: 99In the Introduction, fourth paragraph, it says:

Original Text:

Also ICMP messages are only sent about errors in handling fragment zero of
fragemented datagrams.  (Fragment zero has the fragment offeset equal
zero).

Corrected Text:

Also ICMP messages are only sent about errors in handling fragment zero of
fragmented datagrams.  (Fragment zero has the fragment offset equal
zero).
Notes:
RFC 792 Message Formats ICMP messages are sent using the basic IP header. The first octet of the data portion of the datagram is a ICMP type field; the value of this field determines the format of the remaining data. Any field labeled "unused" is reserved for later extensions and must be zero when sent, but receivers should not use these fields (except to include them in the checksum). Unless otherwise noted under the individual format descriptions, the values of the internet header fields are as follows: Version 4 IHL Internet header length in 32-bit words. Type of Service 0 Total Length Length of internet header and data in octets. Identification, Flags, Fragment Offset Used in fragmentation, see [1]. Time to Live Time to live in seconds; as this field is decremented at each machine in which the datagram is processed, the value in this field should be at least as great as the number of gateways which this datagram will traverse. Protocol ICMP = 1 Header Checksum The 16 bit one's complement of the one's complement sum of all 16 bit words in the header. For computing the checksum, the checksum field should be zero. This checksum may be replaced in the future. [Page 2] September 1981 RFC 792 Source Address The address of the gateway or host that composes the ICMP message. Unless otherwise noted, this can be any of a gateway's addresses. Destination Address The address of the gateway or host to which the message should be sent. RFC 792 Destination Unreachable Message 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Code | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | unused | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Internet Header + 64 bits of Original Data Datagram | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ IP Fields: Destination Address The source network and address from the original datagram's data. ICMP Fields: Type 3 Code 0 = net unreachable; 1 = host unreachable; 2 = protocol unreachable; 3 = port unreachable; 4 = fragmentation needed and DF set; 5 = source route failed. Checksum The checksum is the 16-bit ones's complement of the one's complement sum of the ICMP message starting with the ICMP Type. For computing the checksum , the checksum field should be zero. This checksum may be replaced in the future. Internet Header + 64 bits of Data Datagram The internet header plus the first 64 bits of the original [Page 4] September 1981 RFC 792 datagram's data. This data is used by the host to match the message to the appropriate process. If a higher level protocol uses port numbers, they are assumed to be in the first 64 data bits of the original datagram's data. Description If, according to the information in the gateway's routing tables, the network specified in the internet destination field of a datagram is unreachable, e.g., the distance to the network is infinity, the gateway may send a destination unreachable message to the internet source host of the datagram. In addition, in some networks, the gateway may be able to determine if the internet destination host is unreachable. Gateways in these networks may send destination unreachable messages to the source host when the destination host is unreachable. If, in the destination host, the IP module cannot deliver the datagram because the indicated protocol module or process port is not active, the destination host may send a destination unreachable message to the source host. Another case is when a datagram must be fragmented to be forwarded by a gateway yet the Don't Fragment flag is on. In this case the gateway must discard the datagram and may return a destination unreachable message. Codes 0, 1, 4, and 5 may be received from a gateway. Codes 2 and 3 may be received from a host. RFC 792 Time Exceeded Message 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Code | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | unused | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Internet Header + 64 bits of Original Data Datagram | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ IP Fields: Destination Address The source network and address from the original datagram's data. ICMP Fields: Type 11 Code 0 = time to live exceeded in transit; 1 = fragment reassembly time exceeded. Checksum The checksum is the 16-bit ones's complement of the one's complement sum of the ICMP message starting with the ICMP Type. For computing the checksum , the checksum field should be zero. This checksum may be replaced in the future. Internet Header + 64 bits of Data Datagram The internet header plus the first 64 bits of the original datagram's data. This data is used by the host to match the message to the appropriate process. If a higher level protocol uses port numbers, they are assumed to be in the first 64 data bits of the original datagram's data. Description If the gateway processing a datagram finds the time to live field [Page 6] September 1981 RFC 792 is zero it must discard the datagram. The gateway may also notify the source host via the time exceeded message. If a host reassembling a fragmented datagram cannot complete the reassembly due to missing fragments within its time limit it discards the datagram, and it may send a time exceeded message. If fragment zero is not available then no time exceeded need be sent at all. Code 0 may be received from a gateway. Code 1 may be received from a host. RFC 792 Parameter Problem Message 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Code | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Pointer | unused | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Internet Header + 64 bits of Original Data Datagram | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ IP Fields: Destination Address The source network and address from the original datagram's data. ICMP Fields: Type 12 Code 0 = pointer indicates the error. Checksum The checksum is the 16-bit ones's complement of the one's complement sum of the ICMP message starting with the ICMP Type. For computing the checksum , the checksum field should be zero. This checksum may be replaced in the future. Pointer If code = 0, identifies the octet where an error was detected. Internet Header + 64 bits of Data Datagram The internet header plus the first 64 bits of the original datagram's data. This data is used by the host to match the message to the appropriate process. If a higher level protocol uses port numbers, they are assumed to be in the first 64 data bits of the original datagram's data. [Page 8] September 1981 RFC 792 Description If the gateway or host processing a datagram finds a problem with the header parameters such that it cannot complete processing the datagram it must discard the datagram. One potential source of such a problem is with incorrect arguments in an option. The gateway or host may also notify the source host via the parameter problem message. This message is only sent if the error caused the datagram to be discarded. The pointer identifies the octet of the original datagram's header where the error was detected (it may be in the middle of an option). For example, 1 indicates something is wrong with the Type of Service, and (if there are options present) 20 indicates something is wrong with the type code of the first option. Code 0 may be received from a gateway or a host. RFC 792 Source Quench Message 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Code | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | unused | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Internet Header + 64 bits of Original Data Datagram | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ IP Fields: Destination Address The source network and address of the original datagram's data. ICMP Fields: Type 4 Code 0 Checksum The checksum is the 16-bit ones's complement of the one's complement sum of the ICMP message starting with the ICMP Type. For computing the checksum , the checksum field should be zero. This checksum may be replaced in the future. Internet Header + 64 bits of Data Datagram The internet header plus the first 64 bits of the original datagram's data. This data is used by the host to match the message to the appropriate process. If a higher level protocol uses port numbers, they are assumed to be in the first 64 data bits of the original datagram's data. Description A gateway may discard internet datagrams if it does not have the buffer space needed to queue the datagrams for output to the next network on the route to the destination network. If a gateway [Page 10] September 1981 RFC 792 discards a datagram, it may send a source quench message to the internet source host of the datagram. A destination host may also send a source quench message if datagrams arrive too fast to be processed. The source quench message is a request to the host to cut back the rate at which it is sending traffic to the internet destination. The gateway may send a source quench message for every message that it discards. On receipt of a source quench message, the source host should cut back the rate at which it is sending traffic to the specified destination until it no longer receives source quench messages from the gateway. The source host can then gradually increase the rate at which it sends traffic to the destination until it again receives source quench messages. The gateway or host may send the source quench message when it approaches its capacity limit rather than waiting until the capacity is exceeded. This means that the data datagram which triggered the source quench message may be delivered. Code 0 may be received from a gateway or a host. RFC 792 Redirect Message 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Code | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Gateway Internet Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Internet Header + 64 bits of Original Data Datagram | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ IP Fields: Destination Address The source network and address of the original datagram's data. ICMP Fields: Type 5 Code 0 = Redirect datagrams for the Network. 1 = Redirect datagrams for the Host. 2 = Redirect datagrams for the Type of Service and Network. 3 = Redirect datagrams for the Type of Service and Host. Checksum The checksum is the 16-bit ones's complement of the one's complement sum of the ICMP message starting with the ICMP Type. For computing the checksum , the checksum field should be zero. This checksum may be replaced in the future. Gateway Internet Address Address of the gateway to which traffic for the network specified in the internet destination network field of the original datagram's data should be sent. [Page 12] September 1981 RFC 792 Internet Header + 64 bits of Data Datagram The internet header plus the first 64 bits of the original datagram's data. This data is used by the host to match the message to the appropriate process. If a higher level protocol uses port numbers, they are assumed to be in the first 64 data bits of the original datagram's data. Description The gateway sends a redirect message to a host in the following situation. A gateway, G1, receives an internet datagram from a host on a network to which the gateway is attached. The gateway, G1, checks its routing table and obtains the address of the next gateway, G2, on the route to the datagram's internet destination network, X. If G2 and the host identified by the internet source address of the datagram are on the same network, a redirect message is sent to the host. The redirect message advises the host to send its traffic for network X directly to gateway G2 as this is a shorter path to the destination. The gateway forwards the original datagram's data to its internet destination. For datagrams with the IP source route options and the gateway address in the destination address field, a redirect message is not sent even if there is a better route to the ultimate destination than the next address in the source route. Codes 0, 1, 2, and 3 may be received from a gateway. RFC 792 Echo or Echo Reply Message 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Code | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Identifier | Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Data ... +-+-+-+-+- IP Fields: Addresses The address of the source in an echo message will be the destination of the echo reply message. To form an echo reply message, the source and destination addresses are simply reversed, the type code changed to 0, and the checksum recomputed. ICMP Fields: Type
EID 577 (Verified) is as follows:

Section: 99On p. 16 and 18, it says:

Original Text:

   IP Fields:

   Type

Corrected Text:

   ICMP Fields:

   Type
Notes:
On page 16, the section 'Timestamp and Timestamp Reply Messages' has
the header 'IP Fields:' - first mentioned after the graph and then
again after 'Addresses'. The second one should actually be 'ICMP
Fields:'. This error also occurs in the discussion of the
'Information Request and Information Reply Message' on page 18.

The second 'IP Fields:' section of these two sets of message
descriptions are really talking about fields in the ICMP header not
the IP header.

[This report was updated 2009-03-11 to specify the original and corrected text, as indicated by Nikolai Malykh.]
8 for echo message; 0 for echo reply message. Code 0 Checksum The checksum is the 16-bit ones's complement of the one's complement sum of the ICMP message starting with the ICMP Type. For computing the checksum , the checksum field should be zero. If the total length is odd, the received data is padded with one octet of zeros for computing the checksum. This checksum may be replaced in the future. Identifier If code = 0, an identifier to aid in matching echos and replies, may be zero. Sequence Number [Page 14] September 1981 RFC 792 If code = 0, a sequence number to aid in matching echos and replies, may be zero. Description The data received in the echo message must be returned in the echo reply message. The identifier and sequence number may be used by the echo sender to aid in matching the replies with the echo requests. For example, the identifier might be used like a port in TCP or UDP to identify a session, and the sequence number might be incremented on each echo request sent. The echoer returns these same values in the echo reply. Code 0 may be received from a gateway or a host. RFC 792 Timestamp or Timestamp Reply Message 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Code | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Identifier | Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Originate Timestamp | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Receive Timestamp | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Transmit Timestamp | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ IP Fields: Addresses The address of the source in a timestamp message will be the destination of the timestamp reply message. To form a timestamp reply message, the source and destination addresses are simply reversed, the type code changed to 14, and the checksum recomputed. IP Fields: Type 13 for timestamp message; 14 for timestamp reply message. Code 0 Checksum The checksum is the 16-bit ones's complement of the one's complement sum of the ICMP message starting with the ICMP Type. For computing the checksum , the checksum field should be zero. This checksum may be replaced in the future. Identifier [Page 16] September 1981 RFC 792 If code = 0, an identifier to aid in matching timestamp and replies, may be zero. Sequence Number If code = 0, a sequence number to aid in matching timestamp and replies, may be zero. Description The data received (a timestamp) in the message is returned in the reply together with an additional timestamp. The timestamp is 32 bits of milliseconds since midnight UT. One use of these timestamps is described by Mills [5]. The Originate Timestamp is the time the sender last touched the message before sending it, the Receive Timestamp is the time the echoer first touched it on receipt, and the Transmit Timestamp is the time the echoer last touched the message on sending it. If the time is not available in miliseconds or cannot be provided with respect to midnight UT then any time can be inserted in a timestamp provided the high order bit of the timestamp is also set to indicate this non-standard value. The identifier and sequence number may be used by the echo sender to aid in matching the replies with the requests. For example, the identifier might be used like a port in TCP or UDP to identify a session, and the sequence number might be incremented on each request sent. The destination returns these same values in the reply. Code 0 may be received from a gateway or a host. RFC 792 Information Request or Information Reply Message 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Code | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Identifier | Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ IP Fields: Addresses The address of the source in a information request message will be the destination of the information reply message. To form a information reply message, the source and destination addresses are simply reversed, the type code changed to 16, and the checksum recomputed. IP Fields: Type 15 for information request message; 16 for information reply message. Code 0 Checksum The checksum is the 16-bit ones's complement of the one's complement sum of the ICMP message starting with the ICMP Type. For computing the checksum , the checksum field should be zero. This checksum may be replaced in the future. Identifier If code = 0, an identifier to aid in matching request and replies, may be zero. Sequence Number If code = 0, a sequence number to aid in matching request and replies, may be zero. [Page 18] September 1981 RFC 792 Description This message may be sent with the source network in the IP header source and destination address fields zero (which means "this" network). The replying IP module should send the reply with the addresses fully specified. This message is a way for a host to find out the number of the network it is on. The identifier and sequence number may be used by the echo sender to aid in matching the replies with the requests. For example, the identifier might be used like a port in TCP or UDP to identify a session, and the sequence number might be incremented on each request sent. The destination returns these same values in the reply. Code 0 may be received from a gateway or a host. RFC 792 Summary of Message Types 0 Echo Reply 3 Destination Unreachable 4 Source Quench 5 Redirect 8 Echo 11 Time Exceeded 12 Parameter Problem 13 Timestamp 14 Timestamp Reply 15 Information Request 16 Information Reply [Page 20] September 1981 RFC 792 References [1] Postel, J. (ed.), "Internet Protocol - DARPA Internet Program Protocol Specification," RFC 791, USC/Information Sciences Institute, September 1981. [2] Cerf, V., "The Catenet Model for Internetworking," IEN 48, Information Processing Techniques Office, Defense Advanced Research Projects Agency, July 1978. [3] Strazisar, V., "Gateway Routing: An Implementation Specification", IEN 30, Bolt Beranek and Newman, April 1979. [4] Strazisar, V., "How to Build a Gateway", IEN 109, Bolt Beranek and Newman, August 1979. [5] Mills, D., "DCNET Internet Clock Service," RFC 778, COMSAT Laboratories, April 1981.